From: Max Chou <[email protected]>
Add the support for RTL8852BT/RTL8852BE-VT BT controller on USB interface.
The necessary firmware will be submitted to linux-firmware project.
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 8 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=8520 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Max Chou <[email protected]>
---
changes in v2:
- Add the USB ID for RTL8852BT/RTL8852BE-VT
---
drivers/bluetooth/btrtl.c | 14 ++++++++++++++
drivers/bluetooth/btusb.c | 3 +++
2 files changed, 17 insertions(+)
diff --git a/drivers/bluetooth/btrtl.c b/drivers/bluetooth/btrtl.c
index 277d039ecbb4..cc50de69e8dc 100644
--- a/drivers/bluetooth/btrtl.c
+++ b/drivers/bluetooth/btrtl.c
@@ -69,6 +69,7 @@ enum btrtl_chip_id {
CHIP_ID_8852B = 20,
CHIP_ID_8852C = 25,
CHIP_ID_8851B = 36,
+ CHIP_ID_8852BT = 47,
};
struct id_table {
@@ -307,6 +308,15 @@ static const struct id_table ic_id_table[] = {
.fw_name = "rtl_bt/rtl8851bu_fw",
.cfg_name = "rtl_bt/rtl8851bu_config",
.hw_info = "rtl8851bu" },
+
+ /* 8852BT/8852BE-VT */
+ { IC_INFO(RTL_ROM_LMP_8852A, 0x87, 0xc, HCI_USB),
+ .config_needed = false,
+ .has_rom_version = true,
+ .has_msft_ext = true,
+ .fw_name = "rtl_bt/rtl8852btu_fw",
+ .cfg_name = "rtl_bt/rtl8852btu_config",
+ .hw_info = "rtl8852btu" },
};
static const struct id_table *btrtl_match_ic(u16 lmp_subver, u16 hci_rev,
@@ -645,6 +655,7 @@ static int rtlbt_parse_firmware(struct hci_dev *hdev,
{ RTL_ROM_LMP_8852A, 20 }, /* 8852B */
{ RTL_ROM_LMP_8852A, 25 }, /* 8852C */
{ RTL_ROM_LMP_8851B, 36 }, /* 8851B */
+ { RTL_ROM_LMP_8852A, 47 }, /* 8852BT */
};
if (btrtl_dev->fw_len <= 8)
@@ -1275,6 +1286,7 @@ void btrtl_set_quirks(struct hci_dev *hdev, struct btrtl_device_info *btrtl_dev)
case CHIP_ID_8852B:
case CHIP_ID_8852C:
case CHIP_ID_8851B:
+ case CHIP_ID_8852BT:
set_bit(HCI_QUIRK_VALID_LE_STATES, &hdev->quirks);
set_bit(HCI_QUIRK_WIDEBAND_SPEECH_SUPPORTED, &hdev->quirks);
@@ -1505,6 +1517,8 @@ MODULE_FIRMWARE("rtl_bt/rtl8852bs_fw.bin");
MODULE_FIRMWARE("rtl_bt/rtl8852bs_config.bin");
MODULE_FIRMWARE("rtl_bt/rtl8852bu_fw.bin");
MODULE_FIRMWARE("rtl_bt/rtl8852bu_config.bin");
+MODULE_FIRMWARE("rtl_bt/rtl8852btu_fw.bin");
+MODULE_FIRMWARE("rtl_bt/rtl8852btu_config.bin");
MODULE_FIRMWARE("rtl_bt/rtl8852cu_fw.bin");
MODULE_FIRMWARE("rtl_bt/rtl8852cu_fw_v2.bin");
MODULE_FIRMWARE("rtl_bt/rtl8852cu_config.bin");
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 7835170b1d66..a0a317bac095 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -553,6 +553,9 @@ static const struct usb_device_id quirks_table[] = {
{ USB_DEVICE(0x13d3, 0x3572), .driver_info = BTUSB_REALTEK |
BTUSB_WIDEBAND_SPEECH },
+ /* Realtek 8852BT/8852BE-VT Bluetooth devices */
+ { USB_DEVICE(0x0bda, 0x8520), .driver_info = BTUSB_REALTEK |
+ BTUSB_WIDEBAND_SPEECH },
/* Realtek Bluetooth devices */
{ USB_VENDOR_AND_INTERFACE_INFO(0x0bda, 0xe0, 0x01, 0x01),
.driver_info = BTUSB_REALTEK },
--
2.34.1
This is automated email and please do not reply to this email!
Dear submitter,
Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=812888
---Test result---
Test Summary:
CheckPatch PASS 0.58 seconds
GitLint PASS 0.19 seconds
SubjectPrefix PASS 0.06 seconds
BuildKernel PASS 27.79 seconds
CheckAllWarning PASS 30.53 seconds
CheckSparse PASS 35.69 seconds
CheckSmatch PASS 99.10 seconds
BuildKernel32 PASS 26.90 seconds
TestRunnerSetup PASS 433.16 seconds
TestRunner_l2cap-tester PASS 22.92 seconds
TestRunner_iso-tester PASS 44.56 seconds
TestRunner_bnep-tester PASS 6.77 seconds
TestRunner_mgmt-tester PASS 164.29 seconds
TestRunner_rfcomm-tester PASS 10.70 seconds
TestRunner_sco-tester PASS 14.26 seconds
TestRunner_ioctl-tester PASS 11.73 seconds
TestRunner_mesh-tester PASS 8.70 seconds
TestRunner_smp-tester PASS 9.57 seconds
TestRunner_userchan-tester PASS 7.26 seconds
IncrementalBuild PASS 25.65 seconds
---
Regards,
Linux Bluetooth
Hello:
This patch was applied to bluetooth/bluetooth-next.git (master)
by Luiz Augusto von Dentz <[email protected]>:
On Tue, 26 Dec 2023 19:45:17 +0800 you wrote:
> From: Max Chou <[email protected]>
>
> Add the support for RTL8852BT/RTL8852BE-VT BT controller on USB interface.
> The necessary firmware will be submitted to linux-firmware project.
>
> The device info from /sys/kernel/debug/usb/devices as below.
>
> [...]
Here is the summary with links:
- [v2] Bluetooth: btrtl: Add the support for RTL8852BT/RTL8852BE-VT
https://git.kernel.org/bluetooth/bluetooth-next/c/8f9bb7a1b81b
You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html