Does anyone know how to put a CSR Bluecore chip into continuous
transmit mode using hcitool?
Michael
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
_______________________________________________
Bluez-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-devel
On Fri, 23 Jun 2006, Brand, Chris wrote:
Hi Chris,
> I was looking at how to send the CSR "Enter Device Under Test Mode"
> command, which sounds like it may be related. I found the ogf, ocf and
> parameters in the CSR documentation (0x6, 0x3 and none, in this case).
> Then I used
> hcitool cmd 0x6 0x3
> To send that command to the chip.
This is something different. The device under test mode is intended to be
used with a Bluetooth Tester. When the device is in DUT mode it can be
controlled by a remote (Test) device. More specifics information about DUT
mode can be found in the BT spec.
Ciao,
Peter
> Using Tomcat but need to do more? Need to support web services, security?
> Get stuff done quickly with pre-integrated technology to make your job easier
> Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
> http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
> _______________________________________________
> Bluez-devel mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/bluez-devel
>
| Peter Wippich Voice: +49 30 46776411 |
| G&W Instruments GmbH fax: +49 30 46776419 |
| Gustav-Meyer-Allee 25, Geb. 12 Email: [email protected] |
| D-13355 Berlin / Germany |
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
_______________________________________________
Bluez-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-devel
> > Does anyone know how to put a CSR Bluecore chip into continuous
> > transmit mode using hcitool?
> >
> You can not do that using HCI Tool because this is a CSR
> specific low level testing command (may be you can figure our
> the necessary command sequence, but this will be very complicated).
>
> And as far as I know also the bccmd tool does not support CSR
> RF test commands.
This might be completely off-base, but it might not, so here goes...
I was looking at how to send the CSR "Enter Device Under Test Mode"
command, which sounds like it may be related. I found the ogf, ocf and
parameters in the CSR documentation (0x6, 0x3 and none, in this case).
Then I used
hcitool cmd 0x6 0x3
To send that command to the chip.
Chris
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
_______________________________________________
Bluez-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-devel
Hi Michael,
On Fri, 23 Jun 2006, Michael Frey wrote:
> Does anyone know how to put a CSR Bluecore chip into continuous
> transmit mode using hcitool?
>
You can not do that using HCI Tool because this is a CSR specific
low level testing command (may be you can figure our the necessary command
sequence, but this will be very complicated).
And as far as I know also the bccmd tool does not support CSR RF test
commands.
Ciao,
Peter
>
> Using Tomcat but need to do more? Need to support web services, security?
> Get stuff done quickly with pre-integrated technology to make your job easier
> Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
> http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
> _______________________________________________
> Bluez-devel mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/bluez-devel
>
| Peter Wippich Voice: +49 30 46776411 |
| G&W Instruments GmbH fax: +49 30 46776419 |
| Gustav-Meyer-Allee 25, Geb. 12 Email: [email protected] |
| D-13355 Berlin / Germany |
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
_______________________________________________
Bluez-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-devel
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Michael Frey wrote:
> Does anyone know how to put a CSR Bluecore chip into continuous
> transmit mode using hcitool?
Not with hcitool, check bccmd in the bluez-utils package.
- -Josh
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2.2 (GNU/Linux)
iD8DBQFEnAzqTS8i9jZYpL8RAm/YAJ9/3kIXLQwUZROKoJuQbFNtyC4UswCg3w3D
Z1sDtxlYvpX8qNf7sa7O3Vk=
=3/G+
-----END PGP SIGNATURE-----
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
_______________________________________________
Bluez-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-devel