2020-01-28 06:19:17

by Kalyani Akula

[permalink] [raw]
Subject: [PATCH V6 0/4] Add Xilinx's ZynqMP AES-GCM driver support

This patch set adds support for
- dt-binding docs for Xilinx ZynqMP AES driver
- Adds device tree node for ZynqMP AES driver
- Adds communication layer support for aes in zynqmp.c
- Adds Xilinx ZynqMP driver for AES Algorithm

NOTE: This patchset is based on Michal's branch
https://git.kernel.org/pub/scm/linux/kernel/git/soc/soc.git/log/?h=arm/drivers
because of possible merge conflict for 1/4 patch with below commit
commit 461011b1e1ab ("drivers: firmware: xilinx: Add support for feature check")

V6 Changes:
- Updated SPDX-License-Identifier in xlnx,zynqmp-aes.yaml.

V5 Changes :
- Moved arm64: zynqmp: Add Xilinx AES node from 2/4 to 4/4.
- Moved crypto: Add Xilinx AES driver patch from 4/4 to 3/4.
- Moved dt-bindings patch from 1/4 to 2/4
- Moved firmware: xilinx: Add ZynqMP aes API for AES patch from 3/4 to 1/4
- Converted dt-bindings from .txt to .yaml format.
- Corrected typo in the subject.
- Updated zynqmp-aes node to correct location.
- Replaced ARCH_ZYNQMP with ZYNQMP_FIRMWARE in Kconfig
- Removed extra new lines and added wherever necessary.
- Updated Signed-off-by sequence.
- Ran checkpatch for all patches in the series.

V4 Changes :
- Addressed review comments.

V3 Changes :
- Added software fallback in cases where Hardware doesn't have
the capability to handle the request.
- Removed use of global variable for storing the driver data.
- Enabled CONFIG_CRYPTO_MANAGER_EXTRA_TESTS=y and executed all
the kernel selftests. Also covered tests with tcrypt module.

V2 Changes :
- Converted RFC PATCH to PATCH
- Removed ALG_SET_KEY_TYPE that was added to support keytype
attribute. Taken using setkey interface.
- Removed deprecated BLKCIPHER in Kconfig
- Erased Key/IV from the buffer.
- Renamed zynqmp-aes driver to zynqmp-aes-gcm.
- Addressed few other review comments


Kalyani Akula (4):
firmware: xilinx: Add ZynqMP aes API for AES functionality
dt-bindings: crypto: Add bindings for ZynqMP AES-GCM driver
crypto: Add Xilinx AES driver
arm64: zynqmp: Add Xilinx AES node.

.../bindings/crypto/xlnx,zynqmp-aes.yaml | 37 ++
arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 4 +
drivers/crypto/Kconfig | 12 +
drivers/crypto/Makefile | 1 +
drivers/crypto/xilinx/Makefile | 2 +
drivers/crypto/xilinx/zynqmp-aes-gcm.c | 466 +++++++++++++++++++++
drivers/firmware/xilinx/zynqmp.c | 25 ++
include/linux/firmware/xlnx-zynqmp.h | 2 +
8 files changed, 549 insertions(+)
create mode 100644 Documentation/devicetree/bindings/crypto/xlnx,zynqmp-aes.yaml
create mode 100644 drivers/crypto/xilinx/Makefile
create mode 100644 drivers/crypto/xilinx/zynqmp-aes-gcm.c

--
1.9.5


2020-01-28 06:19:24

by Kalyani Akula

[permalink] [raw]
Subject: [PATCH V6 1/4] firmware: xilinx: Add ZynqMP aes API for AES functionality

Add ZynqMP firmware AES API to perform encryption/decryption of given data.

Signed-off-by: Kalyani Akula <[email protected]>
Acked-by: Michal Simek <[email protected]>
---

V5 Changes:
- Moved firmware: xilinx: Add ZynqMP aes API for AES patch from 3/4 to 1/4
- This patch (1/4) is based on below commit id because of possible merge conflict
commit 461011b1e1ab ("drivers: firmware: xilinx: Add support for feature check")
- Added newlines in between at the start and end of zynqmp_pm_aes_engine function

drivers/firmware/xilinx/zynqmp.c | 25 +++++++++++++++++++++++++
include/linux/firmware/xlnx-zynqmp.h | 2 ++
2 files changed, 27 insertions(+)

diff --git a/drivers/firmware/xilinx/zynqmp.c b/drivers/firmware/xilinx/zynqmp.c
index 0137bf3..20c084f 100644
--- a/drivers/firmware/xilinx/zynqmp.c
+++ b/drivers/firmware/xilinx/zynqmp.c
@@ -705,6 +705,30 @@ static int zynqmp_pm_set_requirement(const u32 node, const u32 capabilities,
qos, ack, NULL);
}

+/**
+ * zynqmp_pm_aes - Access AES hardware to encrypt/decrypt the data using
+ * AES-GCM core.
+ * @address: Address of the AesParams structure.
+ * @out: Returned output value
+ *
+ * Return: Returns status, either success or error code.
+ */
+static int zynqmp_pm_aes_engine(const u64 address, u32 *out)
+{
+ u32 ret_payload[PAYLOAD_ARG_CNT];
+ int ret;
+
+ if (!out)
+ return -EINVAL;
+
+ ret = zynqmp_pm_invoke_fn(PM_SECURE_AES, upper_32_bits(address),
+ lower_32_bits(address),
+ 0, 0, ret_payload);
+ *out = ret_payload[1];
+
+ return ret;
+}
+
static const struct zynqmp_eemi_ops eemi_ops = {
.get_api_version = zynqmp_pm_get_api_version,
.get_chipid = zynqmp_pm_get_chipid,
@@ -728,6 +752,7 @@ static int zynqmp_pm_set_requirement(const u32 node, const u32 capabilities,
.set_requirement = zynqmp_pm_set_requirement,
.fpga_load = zynqmp_pm_fpga_load,
.fpga_get_status = zynqmp_pm_fpga_get_status,
+ .aes = zynqmp_pm_aes_engine,
};

/**
diff --git a/include/linux/firmware/xlnx-zynqmp.h b/include/linux/firmware/xlnx-zynqmp.h
index e72eccf..5455830 100644
--- a/include/linux/firmware/xlnx-zynqmp.h
+++ b/include/linux/firmware/xlnx-zynqmp.h
@@ -82,6 +82,7 @@ enum pm_api_id {
PM_CLOCK_GETRATE,
PM_CLOCK_SETPARENT,
PM_CLOCK_GETPARENT,
+ PM_SECURE_AES = 47,
PM_FEATURE_CHECK = 63,
PM_API_MAX,
};
@@ -313,6 +314,7 @@ struct zynqmp_eemi_ops {
const u32 capabilities,
const u32 qos,
const enum zynqmp_pm_request_ack ack);
+ int (*aes)(const u64 address, u32 *out);
};

int zynqmp_pm_invoke_fn(u32 pm_api_id, u32 arg0, u32 arg1,
--
1.9.5

2020-01-28 06:19:58

by Kalyani Akula

[permalink] [raw]
Subject: [PATCH V6 2/4] dt-bindings: crypto: Add bindings for ZynqMP AES-GCM driver

Add documentation to describe Xilinx ZynqMP AES-GCM driver bindings.

Signed-off-by: Kalyani Akula <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Acked-by: Michal Simek <[email protected]>
---

V6 Changes:
- Updated SPDX-License-Identifier.

V5 Changes:
- Moved dt-bindings patch from 1/4 to 2/4
- Converted dt-bindings from .txt to .yaml format.

.../bindings/crypto/xlnx,zynqmp-aes.yaml | 37 ++++++++++++++++++++++
1 file changed, 37 insertions(+)
create mode 100644 Documentation/devicetree/bindings/crypto/xlnx,zynqmp-aes.yaml

diff --git a/Documentation/devicetree/bindings/crypto/xlnx,zynqmp-aes.yaml b/Documentation/devicetree/bindings/crypto/xlnx,zynqmp-aes.yaml
new file mode 100644
index 0000000..55dd6e3
--- /dev/null
+++ b/Documentation/devicetree/bindings/crypto/xlnx,zynqmp-aes.yaml
@@ -0,0 +1,37 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/crypto/xlnx,zynqmp-aes.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx ZynqMP AES-GCM Hardware Accelerator Device Tree Bindings
+
+maintainers:
+ - Kalyani Akula <[email protected]>
+ - Michal Simek <[email protected]>
+
+description: |
+ The ZynqMP AES-GCM hardened cryptographic accelerator is used to
+ encrypt or decrypt the data with provided key and initialization vector.
+
+properties:
+ compatible:
+ const: xlnx,zynqmp-aes
+
+required:
+ - compatible
+
+additionalProperties: false
+
+examples:
+ - |
+ firmware {
+ zynqmp_firmware: zynqmp-firmware {
+ compatible = "xlnx,zynqmp-firmware";
+ method = "smc";
+ xlnx_aes: zynqmp-aes {
+ compatible = "xlnx,zynqmp-aes";
+ };
+ };
+ };
+...
--
1.9.5

2020-01-28 06:20:00

by Kalyani Akula

[permalink] [raw]
Subject: [PATCH V6 3/4] crypto: Add Xilinx AES driver

This patch adds AES driver support for the Xilinx ZynqMP SoC.

Signed-off-by: Mohan Marutirao Dhanawade <[email protected]>
Signed-off-by: Kalyani Akula <[email protected]>
Acked-by: Michal Simek <[email protected]>
---

V5 Changes:
- Replaced ARCH_ZYNQMP with ZYNQMP_FIRMWARE in Kconfig
- Removed extra new lines.
- Moved crypto: Add Xilinx AES driver patch from 4/4 to 3/4.
- Updated Signed-off-by sequence.

V4 Changes :
- Addressed review comments.

V3 Changes :
- Added software fallback in cases where Hardware doesn't have
the capability to handle the request.
- Removed use of global variable for storing the driver data.

V2 Changes :
- Converted RFC PATCH to PATCH
- Removed ALG_SET_KEY_TYPE that was added to support keytype
attribute. Taken using setkey interface.
- Removed deprecated BLKCIPHER in Kconfig
- Erased Key/IV from the buffer.
- Renamed zynqmp-aes driver to zynqmp-aes-gcm.
- Addressed few other review comments


drivers/crypto/Kconfig | 12 +
drivers/crypto/Makefile | 1 +
drivers/crypto/xilinx/Makefile | 2 +
drivers/crypto/xilinx/zynqmp-aes-gcm.c | 466 +++++++++++++++++++++++++++++++++
4 files changed, 481 insertions(+)
create mode 100644 drivers/crypto/xilinx/Makefile
create mode 100644 drivers/crypto/xilinx/zynqmp-aes-gcm.c

diff --git a/drivers/crypto/Kconfig b/drivers/crypto/Kconfig
index 91eb768..f41e4eb 100644
--- a/drivers/crypto/Kconfig
+++ b/drivers/crypto/Kconfig
@@ -676,6 +676,18 @@ config CRYPTO_DEV_ROCKCHIP
This driver interfaces with the hardware crypto accelerator.
Supporting cbc/ecb chainmode, and aes/des/des3_ede cipher mode.

+config CRYPTO_DEV_ZYNQMP_AES
+ tristate "Support for Xilinx ZynqMP AES hw accelerator"
+ depends on ZYNQMP_FIRMWARE || COMPILE_TEST
+ select CRYPTO_AES
+ select CRYPTO_ENGINE
+ select CRYPTO_AEAD
+ help
+ Xilinx ZynqMP has AES-GCM engine used for symmetric key
+ encryption and decryption. This driver interfaces with AES hw
+ accelerator. Select this if you want to use the ZynqMP module
+ for AES algorithms.
+
config CRYPTO_DEV_MEDIATEK
tristate "MediaTek's EIP97 Cryptographic Engine driver"
depends on (ARM && ARCH_MEDIATEK) || COMPILE_TEST
diff --git a/drivers/crypto/Makefile b/drivers/crypto/Makefile
index 40229d4..d505d16 100644
--- a/drivers/crypto/Makefile
+++ b/drivers/crypto/Makefile
@@ -47,5 +47,6 @@ obj-$(CONFIG_CRYPTO_DEV_VMX) += vmx/
obj-$(CONFIG_CRYPTO_DEV_BCM_SPU) += bcm/
obj-$(CONFIG_CRYPTO_DEV_SAFEXCEL) += inside-secure/
obj-$(CONFIG_CRYPTO_DEV_ARTPEC6) += axis/
+obj-$(CONFIG_CRYPTO_DEV_ZYNQMP_AES) += xilinx/
obj-y += hisilicon/
obj-$(CONFIG_CRYPTO_DEV_AMLOGIC_GXL) += amlogic/
diff --git a/drivers/crypto/xilinx/Makefile b/drivers/crypto/xilinx/Makefile
new file mode 100644
index 0000000..534e32d
--- /dev/null
+++ b/drivers/crypto/xilinx/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_CRYPTO_DEV_ZYNQMP_AES) += zynqmp-aes-gcm.o
diff --git a/drivers/crypto/xilinx/zynqmp-aes-gcm.c b/drivers/crypto/xilinx/zynqmp-aes-gcm.c
new file mode 100644
index 0000000..ca82da5
--- /dev/null
+++ b/drivers/crypto/xilinx/zynqmp-aes-gcm.c
@@ -0,0 +1,466 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx ZynqMP AES Driver.
+ * Copyright (c) 2020 Xilinx Inc.
+ */
+
+#include <crypto/aes.h>
+#include <crypto/engine.h>
+#include <crypto/gcm.h>
+#include <crypto/internal/aead.h>
+#include <crypto/scatterwalk.h>
+
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+
+#include <linux/firmware/xlnx-zynqmp.h>
+
+#define ZYNQMP_DMA_BIT_MASK 32U
+
+#define ZYNQMP_AES_KEY_SIZE AES_KEYSIZE_256
+#define ZYNQMP_AES_AUTH_SIZE 16U
+#define ZYNQMP_KEY_SRC_SEL_KEY_LEN 1U
+#define ZYNQMP_AES_BLK_SIZE 1U
+#define ZYNQMP_AES_MIN_INPUT_BLK_SIZE 4U
+#define ZYNQMP_AES_WORD_LEN 4U
+
+#define ZYNQMP_AES_GCM_TAG_MISMATCH_ERR 0x01
+#define ZYNQMP_AES_WRONG_KEY_SRC_ERR 0x13
+#define ZYNQMP_AES_PUF_NOT_PROGRAMMED 0xE300
+
+enum zynqmp_aead_op {
+ ZYNQMP_AES_DECRYPT = 0,
+ ZYNQMP_AES_ENCRYPT
+};
+
+enum zynqmp_aead_keysrc {
+ ZYNQMP_AES_KUP_KEY = 0,
+ ZYNQMP_AES_DEV_KEY,
+ ZYNQMP_AES_PUF_KEY
+};
+
+struct zynqmp_aead_drv_ctx {
+ union {
+ struct aead_alg aead;
+ } alg;
+ struct device *dev;
+ struct crypto_engine *engine;
+ const struct zynqmp_eemi_ops *eemi_ops;
+};
+
+struct zynqmp_aead_hw_req {
+ u64 src;
+ u64 iv;
+ u64 key;
+ u64 dst;
+ u64 size;
+ u64 op;
+ u64 keysrc;
+};
+
+struct zynqmp_aead_tfm_ctx {
+ struct crypto_engine_ctx engine_ctx;
+ struct device *dev;
+ u8 key[ZYNQMP_AES_KEY_SIZE];
+ u8 *iv;
+ u32 keylen;
+ u32 authsize;
+ enum zynqmp_aead_keysrc keysrc;
+ struct crypto_aead *fbk_cipher;
+};
+
+struct zynqmp_aead_req_ctx {
+ enum zynqmp_aead_op op;
+};
+
+static int zynqmp_aes_aead_cipher(struct aead_request *req)
+{
+ struct crypto_aead *aead = crypto_aead_reqtfm(req);
+ struct zynqmp_aead_tfm_ctx *tfm_ctx = crypto_aead_ctx(aead);
+ struct zynqmp_aead_req_ctx *rq_ctx = aead_request_ctx(req);
+ struct device *dev = tfm_ctx->dev;
+ struct aead_alg *alg = crypto_aead_alg(aead);
+ struct zynqmp_aead_drv_ctx *drv_ctx;
+ struct zynqmp_aead_hw_req *hwreq;
+ dma_addr_t dma_addr_data, dma_addr_hw_req;
+ unsigned int data_size;
+ unsigned int status;
+ size_t dma_size;
+ char *kbuf;
+ int err;
+
+ drv_ctx = container_of(alg, struct zynqmp_aead_drv_ctx, alg.aead);
+
+ if (!drv_ctx->eemi_ops->aes)
+ return -ENOTSUPP;
+
+ if (tfm_ctx->keysrc == ZYNQMP_AES_KUP_KEY)
+ dma_size = req->cryptlen + ZYNQMP_AES_KEY_SIZE
+ + GCM_AES_IV_SIZE;
+ else
+ dma_size = req->cryptlen + GCM_AES_IV_SIZE;
+
+ kbuf = dma_alloc_coherent(dev, dma_size, &dma_addr_data, GFP_KERNEL);
+ if (!kbuf)
+ return -ENOMEM;
+
+ hwreq = dma_alloc_coherent(dev, sizeof(struct zynqmp_aead_hw_req),
+ &dma_addr_hw_req, GFP_KERNEL);
+ if (!hwreq) {
+ dma_free_coherent(dev, dma_size, kbuf, dma_addr_data);
+ return -ENOMEM;
+ }
+
+ data_size = req->cryptlen;
+ scatterwalk_map_and_copy(kbuf, req->src, 0, req->cryptlen, 0);
+ memcpy(kbuf + data_size, req->iv, GCM_AES_IV_SIZE);
+
+ hwreq->src = dma_addr_data;
+ hwreq->dst = dma_addr_data;
+ hwreq->iv = hwreq->src + data_size;
+ hwreq->keysrc = tfm_ctx->keysrc;
+ hwreq->op = rq_ctx->op;
+
+ if (hwreq->op == ZYNQMP_AES_ENCRYPT)
+ hwreq->size = data_size;
+ else
+ hwreq->size = data_size - ZYNQMP_AES_AUTH_SIZE;
+
+ if (hwreq->keysrc == ZYNQMP_AES_KUP_KEY) {
+ memcpy(kbuf + data_size + GCM_AES_IV_SIZE,
+ tfm_ctx->key, ZYNQMP_AES_KEY_SIZE);
+
+ hwreq->key = hwreq->src + data_size + GCM_AES_IV_SIZE;
+ } else {
+ hwreq->key = 0;
+ }
+
+ drv_ctx->eemi_ops->aes(dma_addr_hw_req, &status);
+
+ if (status) {
+ switch (status) {
+ case ZYNQMP_AES_GCM_TAG_MISMATCH_ERR:
+ dev_err(dev, "ERROR: Gcm Tag mismatch\n");
+ break;
+ case ZYNQMP_AES_WRONG_KEY_SRC_ERR:
+ dev_err(dev, "ERROR: Wrong KeySrc, enable secure mode\n");
+ break;
+ case ZYNQMP_AES_PUF_NOT_PROGRAMMED:
+ dev_err(dev, "ERROR: PUF is not registered\n");
+ break;
+ default:
+ dev_err(dev, "ERROR: Unknown error\n");
+ break;
+ }
+ err = -status;
+ } else {
+ if (hwreq->op == ZYNQMP_AES_ENCRYPT)
+ data_size = data_size + ZYNQMP_AES_AUTH_SIZE;
+ else
+ data_size = data_size - ZYNQMP_AES_AUTH_SIZE;
+
+ sg_copy_from_buffer(req->dst, sg_nents(req->dst),
+ kbuf, data_size);
+ err = 0;
+ }
+
+ if (kbuf) {
+ memzero_explicit(kbuf, dma_size);
+ dma_free_coherent(dev, dma_size, kbuf, dma_addr_data);
+ }
+ if (hwreq) {
+ memzero_explicit(hwreq, sizeof(struct zynqmp_aead_hw_req));
+ dma_free_coherent(dev, sizeof(struct zynqmp_aead_hw_req),
+ hwreq, dma_addr_hw_req);
+ }
+ return err;
+}
+
+static int zynqmp_fallback_check(struct zynqmp_aead_tfm_ctx *tfm_ctx,
+ struct aead_request *req)
+{
+ int need_fallback = 0;
+ struct zynqmp_aead_req_ctx *rq_ctx = aead_request_ctx(req);
+
+ if (tfm_ctx->authsize != ZYNQMP_AES_AUTH_SIZE)
+ need_fallback = 1;
+
+ if (tfm_ctx->keysrc == ZYNQMP_AES_KUP_KEY &&
+ tfm_ctx->keylen != ZYNQMP_AES_KEY_SIZE) {
+ need_fallback = 1;
+ }
+ if (req->assoclen != 0 ||
+ req->cryptlen < ZYNQMP_AES_MIN_INPUT_BLK_SIZE) {
+ need_fallback = 1;
+ }
+ if ((req->cryptlen % ZYNQMP_AES_WORD_LEN) != 0)
+ need_fallback = 1;
+
+ if (rq_ctx->op == ZYNQMP_AES_DECRYPT &&
+ req->cryptlen <= ZYNQMP_AES_AUTH_SIZE) {
+ need_fallback = 1;
+ }
+ return need_fallback;
+}
+
+static int zynqmp_handle_aes_req(struct crypto_engine *engine,
+ void *req)
+{
+ struct aead_request *areq =
+ container_of(req, struct aead_request, base);
+ struct crypto_aead *aead = crypto_aead_reqtfm(req);
+ struct zynqmp_aead_tfm_ctx *tfm_ctx = crypto_aead_ctx(aead);
+ struct zynqmp_aead_req_ctx *rq_ctx = aead_request_ctx(areq);
+ struct aead_request *subreq = aead_request_ctx(req);
+ int need_fallback;
+ int err;
+
+ need_fallback = zynqmp_fallback_check(tfm_ctx, areq);
+
+ if (need_fallback) {
+ aead_request_set_tfm(subreq, tfm_ctx->fbk_cipher);
+
+ aead_request_set_callback(subreq, areq->base.flags,
+ NULL, NULL);
+ aead_request_set_crypt(subreq, areq->src, areq->dst,
+ areq->cryptlen, areq->iv);
+ aead_request_set_ad(subreq, areq->assoclen);
+ if (rq_ctx->op == ZYNQMP_AES_ENCRYPT)
+ err = crypto_aead_encrypt(subreq);
+ else
+ err = crypto_aead_decrypt(subreq);
+ } else {
+ err = zynqmp_aes_aead_cipher(areq);
+ }
+
+ crypto_finalize_aead_request(engine, areq, err);
+ return 0;
+}
+
+static int zynqmp_aes_aead_setkey(struct crypto_aead *aead, const u8 *key,
+ unsigned int keylen)
+{
+ struct crypto_tfm *tfm = crypto_aead_tfm(aead);
+ struct zynqmp_aead_tfm_ctx *tfm_ctx =
+ (struct zynqmp_aead_tfm_ctx *)crypto_tfm_ctx(tfm);
+ unsigned char keysrc;
+ int err;
+
+ if (keylen == ZYNQMP_KEY_SRC_SEL_KEY_LEN) {
+ keysrc = *key;
+ if (keysrc == ZYNQMP_AES_KUP_KEY ||
+ keysrc == ZYNQMP_AES_DEV_KEY ||
+ keysrc == ZYNQMP_AES_PUF_KEY) {
+ tfm_ctx->keysrc = (enum zynqmp_aead_keysrc)keysrc;
+ } else {
+ tfm_ctx->keylen = keylen;
+ }
+ } else {
+ tfm_ctx->keylen = keylen;
+ if (keylen == ZYNQMP_AES_KEY_SIZE) {
+ tfm_ctx->keysrc = ZYNQMP_AES_KUP_KEY;
+ memcpy(tfm_ctx->key, key, keylen);
+ }
+ }
+
+ tfm_ctx->fbk_cipher->base.crt_flags &= ~CRYPTO_TFM_REQ_MASK;
+ tfm_ctx->fbk_cipher->base.crt_flags |= (aead->base.crt_flags &
+ CRYPTO_TFM_REQ_MASK);
+
+ err = crypto_aead_setkey(tfm_ctx->fbk_cipher, key, keylen);
+ if (err) {
+ aead->base.crt_flags &= ~CRYPTO_TFM_RES_MASK;
+ aead->base.crt_flags |=
+ (tfm_ctx->fbk_cipher->base.crt_flags &
+ CRYPTO_TFM_RES_MASK);
+ }
+
+ return err;
+}
+
+static int zynqmp_aes_aead_setauthsize(struct crypto_aead *aead,
+ unsigned int authsize)
+{
+ struct crypto_tfm *tfm = crypto_aead_tfm(aead);
+ struct zynqmp_aead_tfm_ctx *tfm_ctx =
+ (struct zynqmp_aead_tfm_ctx *)crypto_tfm_ctx(tfm);
+
+ tfm_ctx->authsize = authsize;
+ return crypto_aead_setauthsize(tfm_ctx->fbk_cipher, authsize);
+}
+
+static int zynqmp_aes_aead_encrypt(struct aead_request *req)
+{
+ struct zynqmp_aead_drv_ctx *drv_ctx;
+ struct crypto_aead *aead = crypto_aead_reqtfm(req);
+ struct aead_alg *alg = crypto_aead_alg(aead);
+ struct zynqmp_aead_req_ctx *rq_ctx = aead_request_ctx(req);
+
+ rq_ctx->op = ZYNQMP_AES_ENCRYPT;
+ drv_ctx = container_of(alg, struct zynqmp_aead_drv_ctx, alg.aead);
+
+ return crypto_transfer_aead_request_to_engine(drv_ctx->engine, req);
+}
+
+static int zynqmp_aes_aead_decrypt(struct aead_request *req)
+{
+ struct zynqmp_aead_drv_ctx *drv_ctx;
+ struct crypto_aead *aead = crypto_aead_reqtfm(req);
+ struct aead_alg *alg = crypto_aead_alg(aead);
+ struct zynqmp_aead_req_ctx *rq_ctx = aead_request_ctx(req);
+
+ rq_ctx->op = ZYNQMP_AES_DECRYPT;
+ drv_ctx = container_of(alg, struct zynqmp_aead_drv_ctx, alg.aead);
+
+ return crypto_transfer_aead_request_to_engine(drv_ctx->engine, req);
+}
+
+static int zynqmp_aes_aead_init(struct crypto_aead *aead)
+{
+ struct crypto_tfm *tfm = crypto_aead_tfm(aead);
+ struct zynqmp_aead_tfm_ctx *tfm_ctx =
+ (struct zynqmp_aead_tfm_ctx *)crypto_tfm_ctx(tfm);
+ struct zynqmp_aead_drv_ctx *drv_ctx;
+ struct aead_alg *alg = crypto_aead_alg(aead);
+
+ drv_ctx = container_of(alg, struct zynqmp_aead_drv_ctx, alg.aead);
+ tfm_ctx->dev = drv_ctx->dev;
+
+ tfm_ctx->engine_ctx.op.do_one_request = zynqmp_handle_aes_req;
+ tfm_ctx->engine_ctx.op.prepare_request = NULL;
+ tfm_ctx->engine_ctx.op.unprepare_request = NULL;
+
+ tfm_ctx->fbk_cipher = crypto_alloc_aead(drv_ctx->alg.aead.base.cra_name,
+ 0,
+ CRYPTO_ALG_NEED_FALLBACK);
+
+ if (IS_ERR(tfm_ctx->fbk_cipher)) {
+ pr_err("%s() Error: failed to allocate fallback for %s\n",
+ __func__, drv_ctx->alg.aead.base.cra_name);
+ return PTR_ERR(tfm_ctx->fbk_cipher);
+ }
+
+ crypto_aead_set_reqsize(aead,
+ max(sizeof(struct zynqmp_aead_req_ctx),
+ sizeof(struct aead_request) +
+ crypto_aead_reqsize(tfm_ctx->fbk_cipher)));
+ return 0;
+}
+
+static void zynqmp_aes_aead_exit(struct crypto_aead *aead)
+{
+ struct crypto_tfm *tfm = crypto_aead_tfm(aead);
+ struct zynqmp_aead_tfm_ctx *tfm_ctx =
+ (struct zynqmp_aead_tfm_ctx *)crypto_tfm_ctx(tfm);
+
+ if (tfm_ctx->fbk_cipher) {
+ crypto_free_aead(tfm_ctx->fbk_cipher);
+ tfm_ctx->fbk_cipher = NULL;
+ }
+ memzero_explicit(tfm_ctx, sizeof(struct zynqmp_aead_tfm_ctx));
+}
+
+static struct zynqmp_aead_drv_ctx aes_drv_ctx = {
+ .alg.aead = {
+ .setkey = zynqmp_aes_aead_setkey,
+ .setauthsize = zynqmp_aes_aead_setauthsize,
+ .encrypt = zynqmp_aes_aead_encrypt,
+ .decrypt = zynqmp_aes_aead_decrypt,
+ .init = zynqmp_aes_aead_init,
+ .exit = zynqmp_aes_aead_exit,
+ .ivsize = GCM_AES_IV_SIZE,
+ .maxauthsize = ZYNQMP_AES_AUTH_SIZE,
+ .base = {
+ .cra_name = "gcm(aes)",
+ .cra_driver_name = "xilinx-zynqmp-aes-gcm",
+ .cra_priority = 200,
+ .cra_flags = CRYPTO_ALG_TYPE_AEAD |
+ CRYPTO_ALG_ASYNC |
+ CRYPTO_ALG_KERN_DRIVER_ONLY |
+ CRYPTO_ALG_NEED_FALLBACK,
+ .cra_blocksize = ZYNQMP_AES_BLK_SIZE,
+ .cra_ctxsize = sizeof(struct zynqmp_aead_tfm_ctx),
+ .cra_module = THIS_MODULE,
+ }
+ }
+};
+
+static int zynqmp_aes_aead_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ int err;
+
+ /* ZynqMP AES driver supports only one instance */
+ if (!aes_drv_ctx.dev)
+ aes_drv_ctx.dev = dev;
+ else
+ return -ENODEV;
+
+ aes_drv_ctx.eemi_ops = zynqmp_pm_get_eemi_ops();
+ if (IS_ERR(aes_drv_ctx.eemi_ops)) {
+ dev_err(dev, "Failed to get ZynqMP EEMI interface\n");
+ return PTR_ERR(aes_drv_ctx.eemi_ops);
+ }
+
+ err = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(ZYNQMP_DMA_BIT_MASK));
+ if (err < 0) {
+ dev_err(dev, "No usable DMA configuration\n");
+ return err;
+ }
+
+ aes_drv_ctx.engine = crypto_engine_alloc_init(dev, 1);
+ if (!aes_drv_ctx.engine) {
+ dev_err(dev, "Cannot alloc AES engine\n");
+ err = -ENOMEM;
+ goto err_engine;
+ }
+
+ err = crypto_engine_start(aes_drv_ctx.engine);
+ if (err) {
+ dev_err(dev, "Cannot start AES engine\n");
+ goto err_engine;
+ }
+
+ err = crypto_register_aead(&aes_drv_ctx.alg.aead);
+ if (err < 0) {
+ dev_err(dev, "Failed to register AEAD alg.\n");
+ goto err_aead;
+ }
+ return 0;
+
+err_aead:
+ crypto_unregister_aead(&aes_drv_ctx.alg.aead);
+
+err_engine:
+ if (aes_drv_ctx.engine)
+ crypto_engine_exit(aes_drv_ctx.engine);
+
+ return err;
+}
+
+static int zynqmp_aes_aead_remove(struct platform_device *pdev)
+{
+ crypto_engine_exit(aes_drv_ctx.engine);
+ crypto_unregister_aead(&aes_drv_ctx.alg.aead);
+
+ return 0;
+}
+
+static const struct of_device_id zynqmp_aes_dt_ids[] = {
+ { .compatible = "xlnx,zynqmp-aes" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, zynqmp_aes_dt_ids);
+
+static struct platform_driver zynqmp_aes_driver = {
+ .probe = zynqmp_aes_aead_probe,
+ .remove = zynqmp_aes_aead_remove,
+ .driver = {
+ .name = "zynqmp-aes",
+ .of_match_table = zynqmp_aes_dt_ids,
+ },
+};
+
+module_platform_driver(zynqmp_aes_driver);
+MODULE_LICENSE("GPL");
--
1.9.5

2020-01-28 06:20:26

by Kalyani Akula

[permalink] [raw]
Subject: [PATCH V6 4/4] arm64: zynqmp: Add Xilinx AES node.

This patch adds a AES DT node for Xilinx ZynqMP SoC.

Signed-off-by: Kalyani Akula <[email protected]>
Acked-by: Michal Simek <[email protected]>
---

V5 Changes:
- Moved arm64: zynqmp: Add Xilinx AES node patch from 2/4 to 4/4
- Corrected typo in the subject.
- Updated zynqmp-aes node to correct location.


arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 4 ++++
1 file changed, 4 insertions(+)

diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
index 3c731e7..e9fbbe1 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
+++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
@@ -133,6 +133,10 @@
zynqmp_pcap: pcap {
compatible = "xlnx,zynqmp-pcap-fpga";
};
+
+ xlnx_aes: zynqmp-aes {
+ compatible = "xlnx,zynqmp-aes";
+ };
};
};

--
1.9.5

2020-02-13 09:03:14

by Herbert Xu

[permalink] [raw]
Subject: Re: [PATCH V6 3/4] crypto: Add Xilinx AES driver

On Tue, Jan 28, 2020 at 11:48:27AM +0530, Kalyani Akula wrote:
> This patch adds AES driver support for the Xilinx ZynqMP SoC.
>
> Signed-off-by: Mohan Marutirao Dhanawade <[email protected]>
> Signed-off-by: Kalyani Akula <[email protected]>
> Acked-by: Michal Simek <[email protected]>
> ---
>
> V5 Changes:
> - Replaced ARCH_ZYNQMP with ZYNQMP_FIRMWARE in Kconfig
> - Removed extra new lines.
> - Moved crypto: Add Xilinx AES driver patch from 4/4 to 3/4.
> - Updated Signed-off-by sequence.

Sorry but this patch doesn't compile against the current cryptodev
tree. Please fix and respost.

Thanks,
--
Email: Herbert Xu <[email protected]>
Home Page: http://gondor.apana.org.au/~herbert/
PGP Key: http://gondor.apana.org.au/~herbert/pubkey.txt

2020-02-17 10:07:18

by Kalyani Akula

[permalink] [raw]
Subject: RE: [PATCH V6 3/4] crypto: Add Xilinx AES driver

Hi Herbert,

The compilation issue is due to commit af5034e8e4a5 ("crypto: remove propagation of CRYPTO_TFM_RES_* flags ").
I will fix it and send V7.

Regards,
Kalyani

> -----Original Message-----
> From: Herbert Xu <[email protected]>
> Sent: Thursday, February 13, 2020 2:33 PM
> To: Kalyani Akula <[email protected]>
> Cc: [email protected]; [email protected]; [email protected];
> [email protected]; Rob Herring <[email protected]>;
> [email protected]; git-dev <[email protected]>; Mohan Marutirao
> Dhanawade <[email protected]>; Sarat Chand Savitala
> <[email protected]>; Harsh Jain <[email protected]>; Michal Simek
> <[email protected]>; Kalyani Akula <[email protected]>; Mohan Marutirao
> Dhanawade <[email protected]>
> Subject: Re: [PATCH V6 3/4] crypto: Add Xilinx AES driver
>
> On Tue, Jan 28, 2020 at 11:48:27AM +0530, Kalyani Akula wrote:
> > This patch adds AES driver support for the Xilinx ZynqMP SoC.
> >
> > Signed-off-by: Mohan Marutirao Dhanawade
> <[email protected]>
> > Signed-off-by: Kalyani Akula <[email protected]>
> > Acked-by: Michal Simek <[email protected]>
> > ---
> >
> > V5 Changes:
> > - Replaced ARCH_ZYNQMP with ZYNQMP_FIRMWARE in Kconfig
> > - Removed extra new lines.
> > - Moved crypto: Add Xilinx AES driver patch from 4/4 to 3/4.
> > - Updated Signed-off-by sequence.
>
> Sorry but this patch doesn't compile against the current cryptodev tree. Please
> fix and respost.
>
> Thanks,
> --
> Email: Herbert Xu <[email protected]> Home Page:
> http://gondor.apana.org.au/~herbert/
> PGP Key: http://gondor.apana.org.au/~herbert/pubkey.txt