With the new kernel 2.6.26.3-14.fc8, I see that the prism54 card looks in a correct working mode
(e.g. /sbin/iwlist wlan0 scan shows good scan results).
But after that, wpa_supplicant cannot associate (gets a timeout)
(while it works ok with 2.6.25.14-69.fc8)
I have put below the output of wpa_supplicant for the bad case
and for the good case.
What can I do to further see what is going wrong ?
Thanks
02:00.0 Network controller: Intersil Corporation ISL3886 [Prism Javelin/Prism Xbow] (rev 01)
Subsystem: Z-Com, Inc. Unknown device 0036
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 32 (2500ns min, 7000ns max), Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fa400000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: prism54pci
Kernel modules: p54pci, prism54
bad:
*******************************
ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 4 value 0x0 - Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'default'
ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group='wheel' (DEPRECATED)
Priority group 0
id=0 ssid='USR9111'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:60:b3:a1:8b:81
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
Setting scan request: 0 sec 100000 usec
ctrl_interface_group=10 (from group name 'wheel')
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=7):
55 53 52 39 31 31 31 USR9111
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 312 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:14:c1:2a:38:12 ssid='USR9111' wpa_ie_len=24 rsn_ie_len=22 caps=0x11
selected based on RSN IE
selected WPA AP 00:14:c1:2a:38:12 ssid='USR9111'
Try to find non-WPA AP
Trying to associate with 00:14:c1:2a:38:12 (SSID='USR9111' freq=2462 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
RSN: using IEEE 802.11i/D9.0
WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 04 01 00 00 50 f2 04 01 00 00 50 f2 02
WPA: set AP RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 01 00
WPA: using GTK CCMP
WPA: using PTK CCMP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
Setting authentication timeout: 20 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RSN: added PMKSA cache candidate 00:14:c1:2a:38:12 prio 1000
RSN: processing PMKSA candidate list
RSN: not in suitable state for new pre-authentication
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b04 len=12
Authentication with 00:14:c1:2a:38:12 timed out.
Added BSSID 00:14:c1:2a:38:12 into blacklist
No keys have been configured - skip key clearing
State: ASSOCIATING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Scan requested (ret=0) - scan timeout 5 seconds
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 311 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:14:c1:2a:38:12 ssid='USR9111' wpa_ie_len=24 rsn_ie_len=22 caps=0x11
selected based on RSN IE
selected WPA AP 00:14:c1:2a:38:12 ssid='USR9111'
Try to find non-WPA AP
Trying to associate with 00:14:c1:2a:38:12 (SSID='USR9111' freq=2462 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
RSN: using IEEE 802.11i/D9.0
WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 04 01 00 00 50 f2 04 01 00 00 50 f2 02
WPA: set AP RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 01 00
WPA: using GTK CCMP
WPA: using PTK CCMP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
Setting authentication timeout: 20 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RSN: added PMKSA cache candidate 00:14:c1:2a:38:12 prio 1000
RSN: processing PMKSA candidate list
RSN: not in suitable state for new pre-authentication
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b04 len=12
Authentication with 00:14:c1:2a:38:12 timed out.
BSSID 00:14:c1:2a:38:12 blacklist count incremented to 2
No keys have been configured - skip key clearing
State: ASSOCIATING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=7):
55 53 52 39 31 31 31 USR9111
Scan requested (ret=0) - scan timeout 30 seconds
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 312 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:14:c1:2a:38:12 ssid='USR9111' wpa_ie_len=24 rsn_ie_len=22 caps=0x11
skip - blacklisted
Try to find non-WPA AP
0: 00:14:c1:2a:38:12 ssid='USR9111' wpa_ie_len=24 rsn_ie_len=22 caps=0x11
skip - blacklisted
No APs found - clear blacklist and try again
Removed BSSID 00:14:c1:2a:38:12 from blacklist (clear)
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:14:c1:2a:38:12 ssid='USR9111' wpa_ie_len=24 rsn_ie_len=22 caps=0x11
selected based on RSN IE
selected WPA AP 00:14:c1:2a:38:12 ssid='USR9111'
Try to find non-WPA AP
Trying to associate with 00:14:c1:2a:38:12 (SSID='USR9111' freq=2462 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
RSN: using IEEE 802.11i/D9.0
WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 04 01 00 00 50 f2 04 01 00 00 50 f2 02
WPA: set AP RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 01 00
WPA: using GTK CCMP
WPA: using PTK CCMP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
Setting authentication timeout: 20 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RSN: added PMKSA cache candidate 00:14:c1:2a:38:12 prio 1000
RSN: processing PMKSA candidate list
RSN: not in suitable state for new pre-authentication
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b04 len=12
Authentication with 00:14:c1:2a:38:12 timed out.
Added BSSID 00:14:c1:2a:38:12 into blacklist
No keys have been configured - skip key clearing
State: ASSOCIATING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Scan requested (ret=0) - scan timeout 30 seconds
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 311 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:14:c1:2a:38:12 ssid='USR9111' wpa_ie_len=24 rsn_ie_len=22 caps=0x11
selected based on RSN IE
selected WPA AP 00:14:c1:2a:38:12 ssid='USR9111'
Try to find non-WPA AP
Trying to associate with 00:14:c1:2a:38:12 (SSID='USR9111' freq=2462 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
RSN: using IEEE 802.11i/D9.0
WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 04 01 00 00 50 f2 04 01 00 00 50 f2 02
WPA: set AP RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 01 00
WPA: using GTK CCMP
WPA: using PTK CCMP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
Setting authentication timeout: 20 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RSN: added PMKSA cache candidate 00:14:c1:2a:38:12 prio 1000
RSN: processing PMKSA candidate list
RSN: not in suitable state for new pre-authentication
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b04 len=12
Authentication with 00:14:c1:2a:38:12 timed out.
BSSID 00:14:c1:2a:38:12 blacklist count incremented to 2
No keys have been configured - skip key clearing
State: ASSOCIATING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=7):
55 53 52 39 31 31 31 USR9111
Scan requested (ret=0) - scan timeout 30 seconds
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 311 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:14:c1:2a:38:12 ssid='USR9111' wpa_ie_len=24 rsn_ie_len=22 caps=0x11
skip - blacklisted
Try to find non-WPA AP
0: 00:14:c1:2a:38:12 ssid='USR9111' wpa_ie_len=24 rsn_ie_len=22 caps=0x11
skip - blacklisted
No APs found - clear blacklist and try again
Removed BSSID 00:14:c1:2a:38:12 from blacklist (clear)
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:14:c1:2a:38:12 ssid='USR9111' wpa_ie_len=24 rsn_ie_len=22 caps=0x11
selected based on RSN IE
sell2_packet_receive - recvfrom: Network is down
ected WPA AP 00:14:c1:2a:38:12 ssid='USR9111'
Try to find non-WPA AP
Trying to associate with 00:14:c1:2a:38:12 (SSID='USR9111' freq=2462 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
RSN: using IEEE 802.11i/D9.0
WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 04 01 00 00 50 f2 04 01 00 00 50 f2 02
WPA: set AP RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 01 00
WPA: using GTK CCMP
WPA: using PTK CCMP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
Setting authentication timeout: 20 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RSN: added PMKSA cache candidate 00:14:c1:2a:38:12 prio 1000
RSN: processing PMKSA candidate list
RSN: not in suitable state for new pre-authentication
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b04 len=12
Authentication with 00:14:c1:2a:38:12 timed out.
Added BSSID 00:14:c1:2a:38:12 into blacklist
No keys have been configured - skip key clearing
State: ASSOCIATING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Scan requested (ret=0) - scan timeout 30 seconds
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 311 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:14:c1:2a:38:12 ssid='USR9111' wpa_ie_len=24 rsn_ie_len=22 caps=0x11
selected based on RSN IE
selected WPA AP 00:14:c1:2a:38:12 ssid='USR9111'
Try to find non-WPA AP
Trying to associate with 00:14:c1:2a:38:12 (SSID='USR9111' freq=2462 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
RSN: using IEEE 802.11i/D9.0
WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 04 01 00 00 50 f2 04 01 00 00 50 f2 02
WPA: set AP RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 01 00
WPA: using GTK CCMP
WPA: using PTK CCMP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
Setting authentication timeout: 20 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RSN: added PMKSA cache candidate 00:14:c1:2a:38:12 prio 1000
RSN: processing PMKSA candidate list
RSN: not in suitable state for new pre-authentication
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b04 len=12
Ignore event for foreign ifindex 3
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
CTRL-EVENT-TERMINATING - signal 15 received
Removing interface wlan0
State: ASSOCIATING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Opeioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 4 value 0x0 - rstate: linkmode=-1, operstate=5
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_wext_set_wpa
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_countermeasures
No keys have been configured - skip key clearing
Removed BSSID 00:14:c1:2a:38:12 from blacklist (clear)
Cancelling scan request
Cancelling authentication timeout
WEXT: Operstate: linkmode=0, operstate=6
good:
**********************************************
ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 4 value 0x0 - Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'default'
ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group='wheel' (DEPRECATED)
Priority group 0
id=0 ssid='USR9111'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:60:b3:a1:8b:81
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
Setting scan request: 0 sec 100000 usec
ctrl_interface_group=10 (from group name 'wheel')
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=7):
55 53 52 39 31 31 31 USR9111
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 312 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:14:c1:2a:38:12 ssid='USR9111' wpa_ie_len=24 rsn_ie_len=22 caps=0x11
selected based on RSN IE
selected WPA AP 00:14:c1:2a:38:12 ssid='USR9111'
Try to find non-WPA AP
Trying to associate with 00:14:c1:2a:38:12 (SSID='USR9111' freq=2462 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
RSN: using IEEE 802.11i/D9.0
WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 04 01 00 00 50 f2 04 01 00 00 50 f2 02
WPA: set AP RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 01 00
WPA: using GTK CCMP
WPA: using PTK CCMP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
Setting authentication timeout: 20 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RSN: added PMKSA cache candidate 00:14:c1:2a:38:12 prio 1000
RSN: processing PMKSA candidate list
RSN: not in suitable state for new pre-authentication
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b04 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8c02 len=161
Association info event
req_ies - hexdump(len=47): 00 07 55 53 52 39 31 31 31 01 08 02 04 0b 16 0c 12 18 24 32 04 30 48 60 6c 30 14 01 00 00 0f ac 04 01 00
00 0f ac 04 01 00 00 0f ac 02 00 00
resp_ies - hexdump(len=16): 01 08 82 84 8b 96 0c 12 18 24 32 04 30 48 60 6c
WPA: set own WPA/RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:14:c1:2a:38:12
State: ASSOCIATING -> ASSOCIATED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
Associated to a new BSS: BSSID=00:14:c1:2a:38:12
No keys have been configured - skip key clearing
Associated with 00:14:c1:2a:38:12
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RX EAPOL from 00:14:c1:2a:38:12
Setting authentication timeout: 10 sec 0 usec
IEEE 802.1X RX: version=1 type=3 length=117
EAPOL-Key type=2
key_info 0x8a (ver=2 keyidx=0 rsvd=0 Pairwise Ack)
key_length=16 key_data_length=22
replay_counter - hexdump(len=8): 00 00 00 00 00 00 02 91
key_nonce - hexdump(len=32): d8 8b 4f 2a 57 96 ef 62 ed 9c 0d 33 fb 0a 15 5e fe 3a 66 e3 a7 bf 49 09 e9 fd 7b d2 a7 46 c7 98
key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
key_mic - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
State: ASSOCIATED -> 4WAY_HANDSHAKE
WPA: RX message 1 of 4-Way Handshake from 00:14:c1:2a:38:12 (ver=2)
RSN: msg 1/4 key data - hexdump(len=22): dd 14 00 0f ac 04 36 2d b4 7d a8 db 2b 82 2c d2 ed dc 01 5f 2a 40
RSN: PMKID from Authenticator - hexdump(len=16): 36 2d b4 7d a8 db 2b 82 2c d2 ed dc 01 5f 2a 40
RSN: no matching PMKID found
WPA: Renewed SNonce - hexdump(len=32): 8b e6 d2 87 c3 7c cd eb 78 f6 49 6b 78 75 c7 14 3d b8 7a 7d dc 17 51 37 d7 04 0d f8 4f 28 35
61
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: WPA IE for msg 2/4 - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
WPA: Sending EAPOL-Key 2/4
RX EAPOL from 00:14:c1:2a:38:12
IEEE 802.1X RX: version=1 type=3 length=151
EAPOL-Key type=2
key_info 0x13ca (ver=2 keyidx=0 rsvd=0 Pairwise Install Ack MIC Secure Encr)
key_length=16 key_data_length=56
replay_counter - hexdump(len=8): 00 00 00 00 00 00 02 92
key_nonce - hexdump(len=32): d8 8b 4f 2a 57 96 ef 62 ed 9c 0d 33 fb 0a 15 5e fe 3a 66 e3 a7 bf 49 09 e9 fd 7b d2 a7 46 c7 98
key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
key_mic - hexdump(len=16): 68 00 60 9a 0a 9d f3 43 9d 56 dc 95 c4 fa eb 7f
RSN: encrypted key data - hexdump(len=56): 85 00 74 bf e3 30 0d 7f 1a 61 0b af 88 8a a1 18 eb a7 41 27 dc e8 7f 66 a4 9e 25 79 50 8b
ca 7d 85 44 a8 3d ae fc ec bb c7 ca 3c ad 61 47 fb 47 a6 60 ff 2d 89 02 63 0c
WPA: decrypted EAPOL-Key key data - hexdump(len=48): [REMOVED]
State: 4WAY_HANDSHAKE -> 4WAY_HANDSHAKE
WPA: RX message 3 of 4-Way Handshake from 00:14:c1:2a:38:12 (ver=2)
WPA: IE KeyData - hexdump(len=48): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 01 00 dd 16 00 0f ac 01 02 00 cb 69
43 2d 9f eb ae 44 7d 2e 92 85 8e b7 d0 ac dd 00
WPA: Sending EAPOL-Key 4/4
WPA: Installing PTK to the driver.
wpa_driver_wext_set_key: alg=3 key_idx=0 set_tx=1 seq_len=6 key_len=16
EAPOL: External notification - portValid=1
State: 4WAY_HANDSHAKE -> GROUP_HANDSHAKE
RSN: received GTK in pairwise handshake - hexdump(len=18): [REMOVED]
WPA: Group Key - hexdump(len=16): [REMOVED]
WPA: Installing GTK to the driver (keyidx=2 tx=0).
WPA: RSC - hexdump(len=6): 00 00 00 00 00 00
wpa_driver_wext_set_key: alg=3 key_idx=2 set_tx=0 seq_len=6 key_len=16
WPA: Key negotiation completed with 00:14:c1:2a:38:12 [PTK=CCMP GTK=CCMP]
Cancelling authentication timeout
State: GROUP_HANDSHAKE -> COMPLETED
CTRL-EVENT-CONNECTED - Connection to 00:14:c1:2a:38:12 completed (auth) [id=0 id_str=]
wpa_driver_wext_set_operstate: operstate 0->1 (UP)
WEXT: Operstate: linkmode=-1, operstate=6
EAPOL: External notification - portValid=1
EAPOL: External notification - EAP success=1
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state SUCCESS
EAP: EAP entering state DISABLED
EAPOL: SUPP_PAE entering state AUTHENTICATED
EAPOL: SUPP_BE entering state IDLE
RTM_NEWLINK: operstate=1 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RSN: processing PMKSA candidate list
RSN: not in suitable state for new pre-authentication
EAPOL: startWhen --> 0
RX EAPOL from 00:14:c1:2a:38:12
IEEE 802.1X RX: version=1 type=3 length=127
EAPOL-Key type=2
key_info 0x1382 (ver=2 keyidx=0 rsvd=0 Group Ack MIC Secure Encr)
key_length=0 key_data_length=32
replay_counter - hexdump(len=8): 00 00 00 00 00 00 02 93
key_nonce - hexdump(len=32): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
key_mic - hexdump(len=16): d6 a2 eb bb 78 d0 00 fe d7 c8 6c 9d d6 d0 b6 a2
RSN: encrypted key data - hexdump(len=32): d0 a1 f4 c4 17 be 4d 26 5f eb 1f 08 fb 7c cd 3a a4 16 de 9a 99 12 70 76 5a 1c 49 37 88 d9
4d 50
WPA: decrypted EAPOL-Key key data - hexdump(len=24): [REMOVED]
WPA: RX message 1 of Group Key Handshake from 00:14:c1:2a:38:12 (ver=2)
RSN: msg 1/2 key data - hexdump(len=24): dd 16 00 0f ac 01 03 00 03 ea f8 37 c1 df 36 ae 54 65 ca 9a 0b 87 44 23
RSN: received GTK in group key handshake - hexdump(len=18): 03 00 03 ea f8 37 c1 df 36 ae 54 65 ca 9a 0b 87 44 23
State: COMPLETED -> GROUP_HANDSHAKE
WPA: Group Key - hexdump(len=16): [REMOVED]
WPA: Installing GTK to the driver (keyidx=3 tx=0).
WPA: RSC - hexdump(len=6): 00 00 00 00 00 00
wpa_driver_wext_set_key: alg=3 key_idx=3 set_tx=0 seq_len=6 key_len=16
WPA: Sending EAPOL-Key 2/2
WPA: Group rekeying completed with 00:14:c1:2a:38:12 [GTK=CCMP]
State: GROUP_HANDSHAKE -> COMPLETED
RX EAPOL from 00:14:c1:2a:38:12
IEEE 802.1X RX: version=1 type=3 length=127
EAPOL-Key type=2
key_info 0x1382 (ver=2 keyidx=0 rsvd=0 Group Ack MIC Secure Encr)
key_length=0 key_data_length=32
replay_counter - hexdump(len=8): 00 00 00 00 00 00 02 94
key_nonce - hexdump(len=32): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
key_mic - hexdump(len=16): b7 2f f0 aa 0b 0f 9b 1e 10 21 46 a2 c0 42 7b 58
RSN: encrypted key data - hexdump(len=32): a7 b3 e8 31 81 8d 2c b6 2f 9c 16 46 00 5a 93 10 5a a3 1c c9 1a ba 59 72 9a be e3 4c 1a 7e
b8 ae
WPA: decrypted EAPOL-Key key data - hexdump(len=24): [REMOVED]
WPA: RX message 1 of Group Key Handshake from 00:14:c1:2a:38:12 (ver=2)
RSN: msg 1/2 key data - hexdump(len=24): dd 16 00 0f ac 01 02 00 8d 82 fd a0 fe 23 09 16 44 7b d3 7d e2 75 ea 57
RSN: received GTK in group key handshake - hexdump(len=18): 02 00 8d 82 fd a0 fe 23 09 16 44 7b d3 7d e2 75 ea 57
State: COMPLETED -> GROUP_HANDSHAKE
WPA: Group Key - hexdump(len=16): [REMOVED]
WPA: Installing GTK to the driver (keyidx=2 tx=0).
WPA: RSC - hexdump(len=6): 00 00 00 00 00 00
wpa_driver_wext_set_key: alg=3 key_idx=2 set_tx=0 seq_len=6 key_len=16
WPA: Sending EAPOL-Key 2/2
WPA: Group rekeying completed with 00:14:c1:2a:38:12 [GTK=CCMP]
State: GROUP_HANDSHAKE -> COMPLETED
CTRL-EVENT-TERMINATING - signal 15 received
Removing interface wlan0
State: COMPLETED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 1->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_deauthenticate
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idxioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 4 value 0x0 - =0 set_tx=0 seq_len=0 key_len=0
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAPOL: External notification - portValid=0
wpa_driver_wext_set_wpa
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_countermeasures
No keys have been configured - skip key clearing
Cancelling scan request
Cancelling authentication timeout
WEXT: Operstate: linkmode=0, operstate=6
On Mon, Sep 22, 2008 at 11:38 AM, Philippe Waroquiers
<[email protected]> wrote:
> With the new kernel 2.6.26.3-14.fc8, I see that the prism54 card looks in a
> correct working mode
> (e.g. /sbin/iwlist wlan0 scan shows good scan results).
> But after that, wpa_supplicant cannot associate (gets a timeout)
> (while it works ok with 2.6.25.14-69.fc8)
> I have put below the output of wpa_supplicant for the bad case
> and for the good case.
>
> What can I do to further see what is going wrong ?
Are you using prism54 or p54 in each kernel?
lsmod | egrep "p54|prism54"
Luis
On Saturday 20 September 2008 23:08:29 Dan Williams wrote:
> On Mon, 2008-09-22 at 22:05 +0200, Chr wrote:
> > On Monday 22 September 2008 20:38:04 Philippe Waroquiers wrote:
> > > With the new kernel 2.6.26.3-14.fc8, I see that the prism54 card looks
> > > in a correct working mode (e.g. /sbin/iwlist wlan0 scan shows good scan
> > > results).
> > > But after that, wpa_supplicant cannot associate (gets a timeout)
> > > (while it works ok with 2.6.25.14-69.fc8)
> > > I have put below the output of wpa_supplicant for the bad case
> > > and for the good case.
> > >
> > > What can I do to further see what is going wrong ?
> >
> > Well, you can blame the fedora people if you want.
> >
> > http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit
> >;h=aaa1553512b9105699113ea7e2ea726f3d9d4de2
>
> Is that commit not in stable 2.6.26 yet or something?
Hmm, no? AFAIK The mac80211 multiqueue changes went in somewhere in the
2.6.27-rc cycle. so 2.6.26.stable doesn't need any extra patches, right?
Regards,
Chr
On Monday 22 September 2008 20:38:04 Philippe Waroquiers wrote:
> With the new kernel 2.6.26.3-14.fc8, I see that the prism54 card looks in a
> correct working mode (e.g. /sbin/iwlist wlan0 scan shows good scan
> results).
> But after that, wpa_supplicant cannot associate (gets a timeout)
> (while it works ok with 2.6.25.14-69.fc8)
> I have put below the output of wpa_supplicant for the bad case
> and for the good case.
>
> What can I do to further see what is going wrong ?
>
Well, you can blame the fedora people if you want.
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=aaa1553512b9105699113ea7e2ea726f3d9d4de2
Regards,
Chr
> Are you using prism54 or p54 in each kernel?
>
> lsmod | egrep "p54|prism54"
p54pci and p54common are found in both kernel
no modules matching prism54
In fact, a few months ago, after a kernel upgrade, I had to blacklist prism54.
(prism54 is still in the blacklist).
Philippe
On Mon, Sep 22, 2008 at 11:59:40PM +0200, Chr wrote:
> On Saturday 20 September 2008 23:44:29 Dan Williams wrote:
> > On Mon, 2008-09-22 at 23:32 +0200, Chr wrote:
> > > > > http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=co
> > > > >mmit ;h=aaa1553512b9105699113ea7e2ea726f3d9d4de2
> > > >
> > > > Is that commit not in stable 2.6.26 yet or something?
> > >
> > > Hmm, no? AFAIK The mac80211 multiqueue changes went in somewhere in the
> > > 2.6.27-rc cycle. so 2.6.26.stable doesn't need any extra patches, right?
> >
> > Ah yeah right; I guess I don't understand the link you posted then. I'd
> > thought it was something like "you need this patch which Fedora doesn't
> > have in their kernel".
> Hmm? I though fedora backported multiqueue back into their 2.6.26?
>
> Atleast, the original (but with a buggy p54) multiqueue patch seems to be in
> the linux-wirless-2.6-pending.diff/patch file... but this fix is nowhere to
> be found inside fedora's kernel source?
>
> So, Dan? can you add that patch to the next fedora's 2.6.26 kernel release?
I pinged Kyle McMartin about it -- he has been doing the wireless
kernel updates in Fedora for a little while now.
John
--
John W. Linville Linux should be at the core
[email protected] of your literate lifestyle.
On Mon, 2008-09-22 at 22:05 +0200, Chr wrote:
> On Monday 22 September 2008 20:38:04 Philippe Waroquiers wrote:
> > With the new kernel 2.6.26.3-14.fc8, I see that the prism54 card looks in a
> > correct working mode (e.g. /sbin/iwlist wlan0 scan shows good scan
> > results).
> > But after that, wpa_supplicant cannot associate (gets a timeout)
> > (while it works ok with 2.6.25.14-69.fc8)
> > I have put below the output of wpa_supplicant for the bad case
> > and for the good case.
> >
> > What can I do to further see what is going wrong ?
> >
>
> Well, you can blame the fedora people if you want.
>
> http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=aaa1553512b9105699113ea7e2ea726f3d9d4de2
Is that commit not in stable 2.6.26 yet or something?
I also had to make sure that only one driver got bound to my card, both
p54 and prism54 fought for it.
Dan
On Saturday 20 September 2008 23:44:29 Dan Williams wrote:
> On Mon, 2008-09-22 at 23:32 +0200, Chr wrote:
> > > > http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=co
> > > >mmit ;h=aaa1553512b9105699113ea7e2ea726f3d9d4de2
> > >
> > > Is that commit not in stable 2.6.26 yet or something?
> >
> > Hmm, no? AFAIK The mac80211 multiqueue changes went in somewhere in the
> > 2.6.27-rc cycle. so 2.6.26.stable doesn't need any extra patches, right?
>
> Ah yeah right; I guess I don't understand the link you posted then. I'd
> thought it was something like "you need this patch which Fedora doesn't
> have in their kernel".
Hmm? I though fedora backported multiqueue back into their 2.6.26?
Atleast, the original (but with a buggy p54) multiqueue patch seems to be in
the linux-wirless-2.6-pending.diff/patch file... but this fix is nowhere to
be found inside fedora's kernel source?
So, Dan? can you add that patch to the next fedora's 2.6.26 kernel release?
Regards,
Chr
On Mon, 2008-09-22 at 23:32 +0200, Chr wrote:
> On Saturday 20 September 2008 23:08:29 Dan Williams wrote:
> > On Mon, 2008-09-22 at 22:05 +0200, Chr wrote:
> > > On Monday 22 September 2008 20:38:04 Philippe Waroquiers wrote:
> > > > With the new kernel 2.6.26.3-14.fc8, I see that the prism54 card looks
> > > > in a correct working mode (e.g. /sbin/iwlist wlan0 scan shows good scan
> > > > results).
> > > > But after that, wpa_supplicant cannot associate (gets a timeout)
> > > > (while it works ok with 2.6.25.14-69.fc8)
> > > > I have put below the output of wpa_supplicant for the bad case
> > > > and for the good case.
> > > >
> > > > What can I do to further see what is going wrong ?
> > >
> > > Well, you can blame the fedora people if you want.
> > >
> > > http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit
> > >;h=aaa1553512b9105699113ea7e2ea726f3d9d4de2
> >
> > Is that commit not in stable 2.6.26 yet or something?
> Hmm, no? AFAIK The mac80211 multiqueue changes went in somewhere in the
> 2.6.27-rc cycle. so 2.6.26.stable doesn't need any extra patches, right?
Ah yeah right; I guess I don't understand the link you posted then. I'd
thought it was something like "you need this patch which Fedora doesn't
have in their kernel".
Dan
On Mon, Sep 22, 2008 at 06:13:21PM -0400, John W. Linville wrote:
> On Mon, Sep 22, 2008 at 11:59:40PM +0200, Chr wrote:
> > On Saturday 20 September 2008 23:44:29 Dan Williams wrote:
> > > On Mon, 2008-09-22 at 23:32 +0200, Chr wrote:
> > > > > > http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=co
> > > > > >mmit ;h=aaa1553512b9105699113ea7e2ea726f3d9d4de2
> > > > >
> > > > > Is that commit not in stable 2.6.26 yet or something?
> > > >
> > > > Hmm, no? AFAIK The mac80211 multiqueue changes went in somewhere in the
> > > > 2.6.27-rc cycle. so 2.6.26.stable doesn't need any extra patches, right?
> > >
> > > Ah yeah right; I guess I don't understand the link you posted then. I'd
> > > thought it was something like "you need this patch which Fedora doesn't
> > > have in their kernel".
> > Hmm? I though fedora backported multiqueue back into their 2.6.26?
> >
> > Atleast, the original (but with a buggy p54) multiqueue patch seems to be in
> > the linux-wirless-2.6-pending.diff/patch file... but this fix is nowhere to
> > be found inside fedora's kernel source?
> >
> > So, Dan? can you add that patch to the next fedora's 2.6.26 kernel release?
>
> I pinged Kyle McMartin about it -- he has been doing the wireless
> kernel updates in Fedora for a little while now.
>
Applied and building in F-9 now... I'll push them into F-8 as well
assuming the build succeeds.
Thanks for the heads ups,
Kyle
> Applied and building in F-9 now... I'll push them into F-8 as well
> assuming the build succeeds.
Note that it seems still broken after upgrading to 2.6.26.5-28.fc8
Philippe