When tx status enabled, retry count is updated from tx completion status.
which is not working as expected due to firmware limitation where
firmware can not provide per MSDU rate statistics from tx completion
status. Due to this tx retry count is always 0 in station dump.
Fix this issue by updating the retry packet count from per peer
statistics. This patch will not break on SDIO devices since, this retry
count is already updating from peer statistics for SDIO devices.
HW used: QCA9984
FW version: 10.4-3.6-00104
Signed-off-by: Venkateswara Naralasetty <[email protected]>
---
drivers/net/wireless/ath/ath10k/htt_rx.c | 8 +++++---
drivers/net/wireless/ath/ath10k/mac.c | 5 +++--
2 files changed, 8 insertions(+), 5 deletions(-)
diff --git a/drivers/net/wireless/ath/ath10k/htt_rx.c b/drivers/net/wireless/ath/ath10k/htt_rx.c
index d787cbe..cac05e7 100644
--- a/drivers/net/wireless/ath/ath10k/htt_rx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_rx.c
@@ -3575,12 +3575,14 @@ ath10k_update_per_peer_tx_stats(struct ath10k *ar,
}
if (ar->htt.disable_tx_comp) {
- arsta->tx_retries += peer_stats->retry_pkts;
arsta->tx_failed += peer_stats->failed_pkts;
- ath10k_dbg(ar, ATH10K_DBG_HTT, "htt tx retries %d tx failed %d\n",
- arsta->tx_retries, arsta->tx_failed);
+ ath10k_dbg(ar, ATH10K_DBG_HTT, "tx failed %d\n",
+ arsta->tx_failed);
}
+ arsta->tx_retries += peer_stats->retry_pkts;
+ ath10k_dbg(ar, ATH10K_DBG_HTT, "htt tx retries %d", arsta->tx_retries);
+
if (ath10k_debug_is_extd_tx_stats_enabled(ar))
ath10k_accumulate_per_peer_tx_stats(ar, arsta, peer_stats,
rate_idx);
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 919d155..d9d4b15 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -8547,12 +8547,13 @@ static void ath10k_sta_statistics(struct ieee80211_hw *hw,
sinfo->filled |= BIT_ULL(NL80211_STA_INFO_TX_BITRATE);
if (ar->htt.disable_tx_comp) {
- sinfo->tx_retries = arsta->tx_retries;
- sinfo->filled |= BIT_ULL(NL80211_STA_INFO_TX_RETRIES);
sinfo->tx_failed = arsta->tx_failed;
sinfo->filled |= BIT_ULL(NL80211_STA_INFO_TX_FAILED);
}
+ sinfo->tx_retries = arsta->tx_retries;
+ sinfo->filled |= BIT_ULL(NL80211_STA_INFO_TX_RETRIES);
+
ath10k_mac_sta_get_peer_stats_info(ar, sta, sinfo);
}
--
2.7.4
On 6/11/20 8:20 AM, Venkateswara Naralasetty wrote:
> When tx status enabled, retry count is updated from tx completion status.
> which is not working as expected due to firmware limitation where
> firmware can not provide per MSDU rate statistics from tx completion
> status. Due to this tx retry count is always 0 in station dump.
>
> Fix this issue by updating the retry packet count from per peer
> statistics. This patch will not break on SDIO devices since, this retry
> count is already updating from peer statistics for SDIO devices.
>
> HW used: QCA9984
> FW version: 10.4-3.6-00104
Thanks a lot for this patch! I tested it on the following HW, where it
also works.
HW: QCA9882
FW: 10.2.4-1.0-00047
Markus
Venkateswara Naralasetty <[email protected]> wrote:
> When tx status enabled, retry count is updated from tx completion status.
> which is not working as expected due to firmware limitation where
> firmware can not provide per MSDU rate statistics from tx completion
> status. Due to this tx retry count is always 0 in station dump.
>
> Fix this issue by updating the retry packet count from per peer
> statistics. This patch will not break on SDIO devices since, this retry
> count is already updating from peer statistics for SDIO devices.
>
> Tested-on: QCA9984 PCI 10.4-3.6-00104
> Tested-on: QCA9882 PCI 10.2.4-1.0-00047
>
> Signed-off-by: Venkateswara Naralasetty <[email protected]>
> Signed-off-by: Kalle Valo <[email protected]>
Patch applied to ath-next branch of ath.git, thanks.
67b927f98208 ath10k: fix retry packets update in station dump
--
https://patchwork.kernel.org/patch/11599289/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches