hello there,
i got the oops below with a rtl8192cu:0bda:8178 and kernel 4.13.6, but
cannot reproduce it.
i use this device since 4.3 or so without noticing any issue.
nirinA
[ 239.338040] usb 2-1.3: new high-speed USB device number 4 using ehci-pci
[ 239.417728] usb 2-1.3: New USB device found, idVendor=0bda,
idProduct=8178
[ 239.417730] usb 2-1.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 239.417731] usb 2-1.3: Product: 802.11n WLAN Adapter
[ 239.417732] usb 2-1.3: Manufacturer: Realtek
[ 239.417733] usb 2-1.3: SerialNumber: 00e04c000001
[ 239.578100] rtl8192cu: Chip version 0x11
[ 239.678225] usb 2-1-port3: disabled by hub (EMI?), re-enabling...
[ 239.678230] usb 2-1.3: USB disconnect, device number 4
[ 239.679128] rtl_usb: reg 0x30, usbctrl_vendorreq TimeOut!
status:0xffffffed value=0x0
[ 239.679131] rtl_usb: reg 0x32, usbctrl_vendorreq TimeOut!
status:0xffffffed value=0x20
[ 239.679133] rtl_usb: reg 0x33, usbctrl_vendorreq TimeOut!
status:0xffffffed value=0x80
[ 239.679134] rtl_usb: reg 0x30, usbctrl_vendorreq TimeOut!
status:0xffffffed value=0x80206f30
[ 239.700640] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[ 239.700648] BUG: unable to handle kernel NULL pointer dereference
at (null)
[ 239.700682] IP: rtl_deinit_core+0x2e/0x90 [rtlwifi]
[ 239.700693] PGD 1c5d5d067
[ 239.700694] P4D 1c5d5d067
[ 239.700701] PUD 1c5d9b067
[ 239.700708] PMD 0
[ 239.700727] Oops: 0000 [#1] SMP
[ 239.700735] Modules linked in: rtl8192cu(+) rtl_usb rtl8192c_common
rtlwifi mac80211 cfg80211 rfkill appletalk ipx p8023 p8022 psnap llc
nct6775 hwmon_vid ipv6 hid_generic usbhid hid coretemp hwmon
x86_pkg_temp_thermal intel_powerclamp snd_hda_codec_hdmi
snd_hda_codec_realtek snd_hda_codec_generic kvm_intel i915 kvm
drm_kms_helper evdev i2c_dev irqbypass syscopyarea sysfillrect sysimgblt
r8169 crc32_pclmul serio_raw crc32c_intel mii snd_pcsp fb_sys_fops drm
fan thermal button battery 8250 8250_base serial_core mei_me
snd_hda_intel mei intel_gtt snd_hda_codec video agpgart ehci_pci
ehci_hcd lpc_ich snd_hwdep snd_hda_core snd_pcm i2c_algo_bit snd_timer
i2c_i801 i2c_core snd soundcore fuse
[ 239.700875] CPU: 0 PID: 1174 Comm: udevd Not tainted 4.13.6.20171012 #1
[ 239.700889] Hardware name: To be filled by O.E.M. To be filled by
O.E.M./ONDA H61V Ver:4.01, BIOS 4.6.5 01/07/2013
[ 239.700909] task: ffff8801c5fbc980 task.stack: ffffc900009a0000
[ 239.700924] RIP: 0010:rtl_deinit_core+0x2e/0x90 [rtlwifi]
[ 239.700936] RSP: 0000:ffffc900009a3b40 EFLAGS: 00010207
[ 239.700947] RAX: 0000000000000282 RBX: ffff8801b9440780 RCX:
00000000ffffffea
[ 239.700962] RDX: 0000000000000001 RSI: 0000000000000282 RDI:
0000000000000000
[ 239.700977] RBP: ffff8801b944b070 R08: 0000000000000001 R09:
00000000000002b0
[ 239.700991] R10: ffffea0008473480 R11: 0000000000000000 R12:
ffff8801b9441560
[ 239.701006] R13: ffff8801b944b880 R14: 0000000000000000 R15:
ffff8801b9441560
[ 239.701021] FS: 00007f3eb636e7c0(0000) GS:ffff88021f200000(0000)
knlGS:0000000000000000
[ 239.701037] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 239.701050] CR2: 0000000000000000 CR3: 00000001c5d99000 CR4:
00000000001406f0
[ 239.701064] Call Trace:
[ 239.701074] ? rtl_usb_probe+0x6b6/0xc50 [rtl_usb]
[ 239.701088] ? usb_probe_interface+0xe2/0x2a0
[ 239.701100] ? driver_probe_device+0x21d/0x2d0
[ 239.701111] ? __driver_attach+0x8a/0x90
[ 239.701121] ? driver_probe_device+0x2d0/0x2d0
[ 239.701133] ? bus_for_each_dev+0x5c/0x90
[ 239.701143] ? bus_add_driver+0x196/0x220
[ 239.701154] ? driver_register+0x57/0xc0
[ 239.701165] ? usb_register_driver+0x7c/0x140
[ 239.701175] ? 0xffffffffa064e000
[ 239.701185] ? do_one_initcall+0x4b/0x190
[ 239.701197] ? kmem_cache_alloc_trace+0xe4/0x1c0
[ 239.701208] ? do_init_module+0x22/0x1e1
[ 239.701219] ? do_init_module+0x5b/0x1e1
[ 239.701229] ? load_module+0x21ff/0x2760
[ 239.701239] ? SYSC_finit_module+0x90/0xb0
[ 239.701249] ? SYSC_finit_module+0x90/0xb0
[ 239.701261] ? entry_SYSCALL_64_fastpath+0x1a/0xa5
[ 239.701272] Code: 00 00 41 57 31 f6 41 56 41 55 41 54 55 53 48 89 fb
e8 e7 fe ff ff 4c 8b 7b 48 49 8b bf 10 9b 00 00 49 8d af 10 9b 00 00 48
39 ef <48> 8b 1f 74 44 49 bd 00 01 00 00 00 00 ad de 49 89 de 49 bc 00
[ 239.701327] RIP: rtl_deinit_core+0x2e/0x90 [rtlwifi] RSP:
ffffc900009a3b40
[ 239.702028] CR2: 0000000000000000
[ 239.705370] ---[ end trace 6ec9029c0d9c0e13 ]---
[ 239.706311] udevd[528]: worker [1174] failed while handling
'/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0'
On Sat, Oct 28, 2017 at 12:02:30AM +0300, nirinA raseliarison wrote:
> On 10/27/2017 07:57 AM, James Cameron wrote:
> >On Fri, Oct 27, 2017 at 04:08:48AM +0300, nirinA raseliarison wrote:
> >>hi all,
> >>i applied the patch against 4.13.8. i still got some trouble, dmesg
> >>is below.
> >
> >As this new event does not have "disabled by hub (EMI?)", it is a
> >different problem to your 19th October post, so I don't think the
> >patch is relevant.
> >
> >>after i plugged the device, it seems to be detected and all modules
> >>loaded, but when i tried to connect to an access point, by using
> >>wicd, it halted after a while. at this point, all usb ports are
> >>broken, there was no more log in dmesg,
> >
> >If the other USB ports are not responding, then your problem is
> >probably wider than the wireless device, and the wireless device
> >is acting as the "canary in the mine"; failing first because it is
> >the most active.
> >
> >Can you test to exclude possibility of damaged USB host controller or
> >hub?
>
> yes, dmesg below with an usb audio adapter and a usb mouse plugged at
> boot time. then the rtl8192cu plugged, and i'm using it to retrieve
> and send this mail.
Thanks.
Your dmesg shows the mouse is discovered, then disconnects, then
reconnects. I can't tell if your mouse normally does this. Can you
also test for the wireless problem without the USB mouse, or with a
different mouse?
Your dmesg also shows "cannot get freq" for USB audio device
endpoints, but I'm not sure what this means.
> my first guess was also about a damaged device or usb port
> as those random crashes are recent.
> note that the device i'm using here is not the same as the one
> that triggered the previous errors.
>
> >>lsusb still showed the device even after being unplugged. it got
> >>even worse as reboot failed.
> >
> >Yes, once a USB host controller is failed, organised reboot can be
> >difficult. lsusb not updated confirms host controller not responding.
> >
> >>i cannot really trace the error as right now all thing works fine.
> >
> >Your dmesg looks like you removed and reinserted the wireless device
> >several times. Did you do that, or did the system do it without any
> >physical action?
>
> no, the device was always connected. i've only removed it long after
> i noticed something went wrong and just before i tried reboot.
Okay, thanks. I'm worried that unexpected disconnect suggests a USB
host or hub problem.
> >A full dmesg from boot may be interesting, at least to better
> >understand the USB host controller.
> >
>
> here it is.
> thanks,
> [...]
--
James Cameron
http://quozl.netrek.org/
On Fri, Oct 27, 2017 at 04:08:48AM +0300, nirinA raseliarison wrote:
> hi all,
> i applied the patch against 4.13.8. i still got some trouble, dmesg
> is below.
As this new event does not have "disabled by hub (EMI?)", it is a
different problem to your 19th October post, so I don't think the
patch is relevant.
> after i plugged the device, it seems to be detected and all modules
> loaded, but when i tried to connect to an access point, by using
> wicd, it halted after a while. at this point, all usb ports are
> broken, there was no more log in dmesg,
If the other USB ports are not responding, then your problem is
probably wider than the wireless device, and the wireless device
is acting as the "canary in the mine"; failing first because it is
the most active.
Can you test to exclude possibility of damaged USB host controller or
hub?
> lsusb still showed the device even after being unplugged. it got
> even worse as reboot failed.
Yes, once a USB host controller is failed, organised reboot can be
difficult. lsusb not updated confirms host controller not responding.
> i cannot really trace the error as right now all thing works fine.
Your dmesg looks like you removed and reinserted the wireless device
several times. Did you do that, or did the system do it without any
physical action?
A full dmesg from boot may be interesting, at least to better
understand the USB host controller.
--
James Cameron
http://quozl.netrek.org/
On 10/18/2017 06:18 PM, nirinA wrote:
> not really a rtlwifi oops then. maybe issue with udev as that also disabled the
> usb mouse.
> but i have no problem since. i will report if i will catch it again.
>
> thanks,
>
> --
> nirinA
>
> James Cameron wrote:
>> On Thu, Oct 19, 2017 at 01:31:43AM +0300, nirinA wrote:
>>> hello there,
>>> i got the oops below with a rtl8192cu:0bda:8178 and kernel 4.13.6, but
>>> cannot reproduce it.
>>> i use this device since 4.3 or so without noticing any issue.
>>>
>>> nirinA
>>>
>>> [ 239.338040] usb 2-1.3: new high-speed USB device number 4 using ehci-pci
>>> [ 239.417728] usb 2-1.3: New USB device found, idVendor=0bda,
>>> idProduct=8178
>>> [ 239.417730] usb 2-1.3: New USB device strings: Mfr=1, Product=2,
>>> SerialNumber=3
>>> [ 239.417731] usb 2-1.3: Product: 802.11n WLAN Adapter
>>> [ 239.417732] usb 2-1.3: Manufacturer: Realtek
>>> [ 239.417733] usb 2-1.3: SerialNumber: 00e04c000001
>>> [ 239.578100] rtl8192cu: Chip version 0x11
>>> [ 239.678225] usb 2-1-port3: disabled by hub (EMI?), re-enabling...
>> Just prior to the oops, your USB hub disabled the port being used by
>> the wireless device.
>>
>> While the response of the driver seems wrong, it is a difficult
>> condition to reproduce; one must either force or forge the disabling
>> by the hub.
>>
>>> [ 239.678230] usb 2-1.3: USB disconnect, device number 4
>>> [ 239.679128] rtl_usb: reg 0x30, usbctrl_vendorreq TimeOut!
>>> status:0xffffffed value=0x0
This sequence of events is unusual. A driver should be able to trust that the
platform is behaving correctly and normally.
In reviewing the USB probe routine, the only thing I could see is that one
returned value is not being checked. If the problem happens again, please try
the following patch:
diff --git a/drivers/net/wireless/realtek/rtlwifi/usb.c
b/drivers/net/wireless/realtek/rtlwifi/usb.c
index 5590d07d0918..092cd2da15f6 100644
--- a/drivers/net/wireless/realtek/rtlwifi/usb.c
+++ b/drivers/net/wireless/realtek/rtlwifi/usb.c
@@ -1082,6 +1082,8 @@ int rtl_usb_probe(struct usb_interface *intf,
init_completion(&rtlpriv->firmware_loading_complete);
SET_IEEE80211_DEV(hw, &intf->dev);
udev = interface_to_usbdev(intf);
+ if (!udev)
+ return -ENODEV;
usb_get_dev(udev);
usb_priv = rtl_usbpriv(hw);
memset(usb_priv, 0, sizeof(*usb_priv));
I will test and push this patch because that value should be checked, but I'm
not sure it would correct your problem.
Larry
i checked my dmesg and have this similar log, i think when i unplugged
the device.
[ 5640.100541] usb 2-1.4: USB disconnect, device number 5
[ 5640.104108] rtl_usb: reg 0x102, usbctrl_vendorreq TimeOut!
status:0xffffffed value=0x0
[ 5640.104110] rtl_usb: reg 0x422, usbctrl_vendorreq TimeOut!
status:0xffffffed value=0x0
[ 5640.104113] rtl_usb: reg 0x542, usbctrl_vendorreq TimeOut!
status:0xffffffed value=0x0
[ 5640.104127] rtl_usb: reg 0x102, usbctrl_vendorreq TimeOut!
status:0xffffffed value=0xd38000
i will apply the patch and will see if i still get this.
thanks,
--
nirinA Larry Finger wrote:
> On 10/18/2017 06:18 PM, nirinA wrote:
>> not really a rtlwifi oops then. maybe issue with udev as that also
>> disabled the usb mouse.
>> but i have no problem since. i will report if i will catch it again.
>>
>> thanks,
>>
>> --
>> nirinA
>>
>> James Cameron wrote:
>>> On Thu, Oct 19, 2017 at 01:31:43AM +0300, nirinA wrote:
>>>> hello there,
>>>> i got the oops below with a rtl8192cu:0bda:8178 and kernel 4.13.6, but
>>>> cannot reproduce it.
>>>> i use this device since 4.3 or so without noticing any issue.
>>>>
>>>> nirinA
>>>>
>>>> [ 239.338040] usb 2-1.3: new high-speed USB device number 4 using
>>>> ehci-pci
>>>> [ 239.417728] usb 2-1.3: New USB device found, idVendor=0bda,
>>>> idProduct=8178
>>>> [ 239.417730] usb 2-1.3: New USB device strings: Mfr=1, Product=2,
>>>> SerialNumber=3
>>>> [ 239.417731] usb 2-1.3: Product: 802.11n WLAN Adapter
>>>> [ 239.417732] usb 2-1.3: Manufacturer: Realtek
>>>> [ 239.417733] usb 2-1.3: SerialNumber: 00e04c000001
>>>> [ 239.578100] rtl8192cu: Chip version 0x11
>>>> [ 239.678225] usb 2-1-port3: disabled by hub (EMI?), re-enabling...
>>> Just prior to the oops, your USB hub disabled the port being used by
>>> the wireless device.
>>>
>>> While the response of the driver seems wrong, it is a difficult
>>> condition to reproduce; one must either force or forge the disabling
>>> by the hub.
>>>
>>>> [ 239.678230] usb 2-1.3: USB disconnect, device number 4
>>>> [ 239.679128] rtl_usb: reg 0x30, usbctrl_vendorreq TimeOut!
>>>> status:0xffffffed value=0x0
>
> This sequence of events is unusual. A driver should be able to trust
> that the platform is behaving correctly and normally.
>
> In reviewing the USB probe routine, the only thing I could see is that
> one returned value is not being checked. If the problem happens again,
> please try the following patch:
>
> diff --git a/drivers/net/wireless/realtek/rtlwifi/usb.c
> b/drivers/net/wireless/realtek/rtlwifi/usb.c
> index 5590d07d0918..092cd2da15f6 100644
> --- a/drivers/net/wireless/realtek/rtlwifi/usb.c
> +++ b/drivers/net/wireless/realtek/rtlwifi/usb.c
> @@ -1082,6 +1082,8 @@ int rtl_usb_probe(struct usb_interface *intf,
> init_completion(&rtlpriv->firmware_loading_complete);
> SET_IEEE80211_DEV(hw, &intf->dev);
> udev = interface_to_usbdev(intf);
> + if (!udev)
> + return -ENODEV;
> usb_get_dev(udev);
> usb_priv = rtl_usbpriv(hw);
> memset(usb_priv, 0, sizeof(*usb_priv));
>
> I will test and push this patch because that value should be checked,
> but I'm not sure it would correct your problem.
>
> Larry
>
>
>
On 10/28/2017 01:57 AM, James Cameron wrote:
> [snip]
> Your dmesg shows the mouse is discovered, then disconnects, then
> reconnects. I can't tell if your mouse normally does this. Can you
> also test for the wireless problem without the USB mouse, or with a
> different mouse?
a new dmesg below with another usb mouse.
> Your dmesg also shows "cannot get freq" for USB audio device
> endpoints, but I'm not sure what this means.
it seems that this device does not support reading the sample rate.
i added its usb id in sound/usb/quirks.c:snd_usb_get_sample_rate_quirk
so that this "cannot get freq" is not logged anymore.
> [snip]
thanks,
[ 0.000000] random: get_random_bytes called from
start_kernel+0x2a/0x413 with crng_init=0
[ 0.000000] Linux version 4.13.8.20171019 (root@supernova) (gcc
version 7.2.0 (GCC)) #2 SMP Sat Oct 28 16:27:44 EAT 2017
[ 0.000000] Command line: BOOT_IMAGE=nirinA ro root=802
vt.default_utf8=0 console=tty0 raid=noautodetect
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating
point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.000000] x86/fpu: Enabled xstate features 0x3, context size is 576
bytes, using 'standard' format.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x0000000020200000-0x0000000040003fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000040004000-0x0000000040004fff]
reserved
[ 0.000000] BIOS-e820: [mem 0x0000000040005000-0x00000000cdf30fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000cdf31000-0x00000000ce25afff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ce25b000-0x00000000ce25bfff]
ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000ce25c000-0x00000000ce373fff]
ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000ce374000-0x00000000ce6d8fff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ce6d9000-0x00000000ce6d9fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000ce6da000-0x00000000ce71cfff]
ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000ce71d000-0x00000000cee19fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000cee1a000-0x00000000ceff1fff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ceff2000-0x00000000ceffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000cf800000-0x00000000df9fffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000021f5fffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] random: fast init done
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: To be filled by O.E.M. To be filled by O.E.M./ONDA
H61V Ver:4.01, BIOS 4.6.5 01/07/2013
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x21f600 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-D3FFF write-protect
[ 0.000000] D4000-E7FFF uncachable
[ 0.000000] E8000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask E00000000 write-back
[ 0.000000] 1 base 200000000 mask FE0000000 write-back
[ 0.000000] 2 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 3 base 0D0000000 mask FF0000000 uncachable
[ 0.000000] 4 base 0CF800000 mask FFF800000 uncachable
[ 0.000000] 5 base 21F800000 mask FFF800000 uncachable
[ 0.000000] 6 base 21F600000 mask FFFE00000 uncachable
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WC UC- WT
[ 0.000000] e820: update [mem 0xcf800000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xcf000 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000fd6f0-0x000fd6ff] mapped
at [ffff8800000fd6f0]
[ 0.000000] Base memory trampoline at [ffff880000097000] 97000 size 24576
[ 0.000000] BRK [0x02145000, 0x02145fff] PGTABLE
[ 0.000000] BRK [0x02146000, 0x02146fff] PGTABLE
[ 0.000000] BRK [0x02147000, 0x02147fff] PGTABLE
[ 0.000000] BRK [0x02148000, 0x02148fff] PGTABLE
[ 0.000000] BRK [0x02149000, 0x02149fff] PGTABLE
[ 0.000000] BRK [0x0214a000, 0x0214afff] PGTABLE
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F0490 000024 (v02 ALASKA)
[ 0.000000] ACPI: XSDT 0x00000000CE362070 000064 (v01 ALASKA A M I
01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 0x00000000CE36B698 0000F4 (v04 ALASKA A M I
01072009 AMI 00010013)
[ 0.000000] ACPI: DSDT 0x00000000CE362170 009526 (v02 ALASKA A M I
00000660 INTL 20051117)
[ 0.000000] ACPI: FACS 0x00000000CE372F80 000040
[ 0.000000] ACPI: APIC 0x00000000CE36B790 000062 (v03 ALASKA A M I
01072009 AMI 00010013)
[ 0.000000] ACPI: FPDT 0x00000000CE36B7F8 000044 (v01 ALASKA A M I
01072009 AMI 00010013)
[ 0.000000] ACPI: MCFG 0x00000000CE36B840 00003C (v01 ALASKA A M I
01072009 MSFT 00000097)
[ 0.000000] ACPI: HPET 0x00000000CE36B880 000038 (v01 ALASKA A M I
01072009 AMI. 00000005)
[ 0.000000] ACPI: SSDT 0x00000000CE36B8B8 00036D (v01 SataRe SataTabl
00001000 INTL 20091112)
[ 0.000000] ACPI: SSDT 0x00000000CE36BC28 000860 (v01 PmRef Cpu0Ist
00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 0x00000000CE36C488 000A92 (v01 PmRef CpuPm
00003000 INTL 20051117)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000021f5fffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009cfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x000000001fffffff]
[ 0.000000] node 0: [mem 0x0000000020200000-0x0000000040003fff]
[ 0.000000] node 0: [mem 0x0000000040005000-0x00000000cdf30fff]
[ 0.000000] node 0: [mem 0x00000000ce6d9000-0x00000000ce6d9fff]
[ 0.000000] node 0: [mem 0x00000000ce71d000-0x00000000cee19fff]
[ 0.000000] node 0: [mem 0x00000000ceff2000-0x00000000ceffffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000021f5fffff]
[ 0.000000] Initmem setup node 0 [mem
0x0000000000001000-0x000000021f5fffff]
[ 0.000000] On node 0 totalpages: 2021848
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3996 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 13137 pages used for memmap
[ 0.000000] DMA32 zone: 840764 pages, LIFO batch:31
[ 0.000000] Normal zone: 18392 pages used for memmap
[ 0.000000] Normal zone: 1177088 pages, LIFO batch:31
[ 0.000000] Reserving Intel graphics memory at
0x00000000cfa00000-0x00000000df9fffff
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI
0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009dfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x20000000-0x201fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x40004000-0x40004fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcdf31000-0xce25afff]
[ 0.000000] PM: Registered nosave memory: [mem 0xce25b000-0xce25bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xce25c000-0xce373fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xce374000-0xce6d8fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xce6da000-0xce71cfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcee1a000-0xceff1fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcf000000-0xcf7fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcf800000-0xdf9fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdfa00000-0xf7ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed03fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed1bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[ 0.000000] e820: [mem 0xdfa00000-0xf7ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff
max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2
nr_node_ids:1
[ 0.000000] percpu: Embedded 37 pages/cpu @ffff88021f200000 s111192
r8192 d32168 u1048576
[ 0.000000] pcpu-alloc: s111192 r8192 d32168 u1048576 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 1990234
[ 0.000000] Kernel command line: BOOT_IMAGE=nirinA ro root=802
vt.default_utf8=0 console=tty0 raid=noautodetect
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 1048576 (order: 11,
8388608 bytes)
[ 0.000000] Inode-cache hash table entries: 524288 (order: 10,
4194304 bytes)
[ 0.000000] Memory: 7863988K/8087392K available (9617K kernel code,
1116K rwdata, 3012K rodata, 1440K init, 660K bss, 223404K reserved, 0K
cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] ftrace: allocating 36813 entries in 144 pages
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 4352, nr_irqs: 440, preallocated irqs: 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 133484882848 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.001000] tsc: Detected 2594.092 MHz processor
[ 0.001000] Calibrating delay loop (skipped), value calculated using
timer frequency.. 5188.18 BogoMIPS (lpj=2594092)
[ 0.001000] pid_max: default: 32768 minimum: 301
[ 0.001000] ACPI: Core revision 20170531
[ 0.005768] ACPI: 4 ACPI AML tables successfully acquired and loaded
[ 0.005790] Security Framework initialized
[ 0.005820] Mount-cache hash table entries: 16384 (order: 5, 131072
bytes)
[ 0.005846] Mountpoint-cache hash table entries: 16384 (order: 5,
131072 bytes)
[ 0.005986] CPU: Physical Processor ID: 0
[ 0.005989] CPU: Processor Core ID: 0
[ 0.006003] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.006006] ENERGY_PERF_BIAS: View and update with
x86_energy_perf_policy(8)
[ 0.006011] mce: CPU supports 7 MCE banks
[ 0.006020] CPU0: Thermal monitoring enabled (TM1)
[ 0.006030] process: using mwait in idle threads
[ 0.006035] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 8
[ 0.006038] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
[ 0.006113] Freeing SMP alternatives memory: 36K
[ 0.007221] smpboot: Max logical packages: 1
[ 0.007634] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.017648] TSC deadline timer enabled
[ 0.017650] smpboot: CPU0: Intel(R) Celeron(R) CPU G1610 @ 2.60GHz
(family: 0x6, model: 0x3a, stepping: 0x9)
[ 0.017703] Performance Events: PEBS fmt1+, IvyBridge events, 16-deep
LBR, full-width counters, Intel PMU driver.
[ 0.017727] ... version: 3
[ 0.017730] ... bit width: 48
[ 0.017733] ... generic registers: 8
[ 0.017736] ... value mask: 0000ffffffffffff
[ 0.017739] ... max period: 00007fffffffffff
[ 0.017741] ... fixed-purpose events: 3
[ 0.017744] ... event mask: 00000007000000ff
[ 0.017774] Hierarchical SRCU implementation.
[ 0.017842] smp: Bringing up secondary CPUs ...
[ 0.017890] x86: Booting SMP configuration:
[ 0.017893] .... node #0, CPUs: #1
[ 0.078018] smp: Brought up 1 node, 2 CPUs
[ 0.078018] smpboot: Total of 2 processors activated (10380.04 BogoMIPS)
[ 0.079123] devtmpfs: initialized
[ 0.079123] x86/mm: Memory block size: 128MB
[ 0.079492] PM: Registering ACPI NVS region [mem
0xce25c000-0xce373fff] (1146880 bytes)
[ 0.079492] PM: Registering ACPI NVS region [mem
0xce6da000-0xce71cfff] (274432 bytes)
[ 0.079492] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.079492] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.079492] pinctrl core: initialized pinctrl subsystem
[ 0.079492] NET: Registered protocol family 16
[ 0.080029] cpuidle: using governor ladder
[ 0.080029] cpuidle: using governor menu
[ 0.080029] PCCT header not found.
[ 0.080048] ACPI: bus type PCI registered
[ 0.080052] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.080083] PCI: Using configuration type 1 for base access
[ 0.080122] core: PMU erratum BJ122, BV98, HSD29 workaround disabled,
HT off
[ 0.083373] ACPI: Added _OSI(Module Device)
[ 0.083373] ACPI: Added _OSI(Processor Device)
[ 0.083373] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.083373] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.083373] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.086305] ACPI: Dynamic OEM Table Load:
[ 0.086315] ACPI: SSDT 0xFFFF880216669000 00083B (v01 PmRef Cpu0Cst
00003001 INTL 20051117)
[ 0.086395] ACPI: Dynamic OEM Table Load:
[ 0.086395] ACPI: SSDT 0xFFFF88021642DC00 000303 (v01 PmRef ApIst
00003000 INTL 20051117)
[ 0.087037] ACPI: Dynamic OEM Table Load:
[ 0.087042] ACPI: SSDT 0xFFFF880216708200 000119 (v01 PmRef ApCst
00003000 INTL 20051117)
[ 0.087380] ACPI: Interpreter enabled
[ 0.087401] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.087405] ACPI: Using IOAPIC for interrupt routing
[ 0.087428] PCI: Using host bridge windows from ACPI; if necessary,
use "pci=nocrs" and report a bug
[ 0.092834] ACPI: Power Resource [FN00] (off)
[ 0.092897] ACPI: Power Resource [FN01] (off)
[ 0.092958] ACPI: Power Resource [FN02] (off)
[ 0.093018] ACPI: Power Resource [FN03] (off)
[ 0.093078] ACPI: Power Resource [FN04] (off)
[ 0.093479] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.093486] acpi PNP0A08:00: _OSC: OS supports [ASPM ClockPM Segments
MSI]
[ 0.093607] acpi PNP0A08:00: _OSC: not requesting OS control; OS
requires [ExtendedConfig ASPM ClockPM MSI]
[ 0.093968] PCI host bridge to bus 0000:00
[ 0.093973] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 0.093976] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.093980] pci_bus 0000:00: root bus resource [mem
0x000a0000-0x000bffff window]
[ 0.093985] pci_bus 0000:00: root bus resource [mem
0x000d4000-0x000d7fff window]
[ 0.093990] pci_bus 0000:00: root bus resource [mem
0x000d8000-0x000dbfff window]
[ 0.093996] pci_bus 0000:00: root bus resource [mem
0x000dc000-0x000dffff window]
[ 0.094000] pci_bus 0000:00: root bus resource [mem
0x000e0000-0x000e3fff window]
[ 0.094006] pci_bus 0000:00: root bus resource [mem
0x000e4000-0x000e7fff window]
[ 0.094012] pci_bus 0000:00: root bus resource [mem
0xdfa00000-0xfeafffff window]
[ 0.094017] pci_bus 0000:00: root bus resource [bus 00-3e]
[ 0.094026] pci 0000:00:00.0: [8086:0150] type 00 class 0x060000
[ 0.094104] pci 0000:00:02.0: [8086:0152] type 00 class 0x030000
[ 0.094114] pci 0000:00:02.0: reg 0x10: [mem 0xf7800000-0xf7bfffff 64bit]
[ 0.094119] pci 0000:00:02.0: reg 0x18: [mem 0xe0000000-0xefffffff
64bit pref]
[ 0.094123] pci 0000:00:02.0: reg 0x20: [io 0xf000-0xf03f]
[ 0.094216] pci 0000:00:16.0: [8086:1c3a] type 00 class 0x078000
[ 0.094241] pci 0000:00:16.0: reg 0x10: [mem 0xf7c0a000-0xf7c0a00f 64bit]
[ 0.094312] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.094384] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320
[ 0.094406] pci 0000:00:1a.0: reg 0x10: [mem 0xf7c08000-0xf7c083ff]
[ 0.094488] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.094554] pci 0000:00:1b.0: [8086:1c20] type 00 class 0x040300
[ 0.094571] pci 0000:00:1b.0: reg 0x10: [mem 0xf7c00000-0xf7c03fff 64bit]
[ 0.094637] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.094704] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400
[ 0.094780] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.094850] pci 0000:00:1c.2: [8086:1c14] type 01 class 0x060400
[ 0.094925] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.094999] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320
[ 0.095020] pci 0000:00:1d.0: reg 0x10: [mem 0xf7c07000-0xf7c073ff]
[ 0.095102] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.095170] pci 0000:00:1f.0: [8086:1c5c] type 00 class 0x060100
[ 0.095334] pci 0000:00:1f.2: [8086:1c02] type 00 class 0x010601
[ 0.095352] pci 0000:00:1f.2: reg 0x10: [io 0xf0b0-0xf0b7]
[ 0.095359] pci 0000:00:1f.2: reg 0x14: [io 0xf0a0-0xf0a3]
[ 0.095367] pci 0000:00:1f.2: reg 0x18: [io 0xf090-0xf097]
[ 0.095374] pci 0000:00:1f.2: reg 0x1c: [io 0xf080-0xf083]
[ 0.095381] pci 0000:00:1f.2: reg 0x20: [io 0xf060-0xf07f]
[ 0.095388] pci 0000:00:1f.2: reg 0x24: [mem 0xf7c06000-0xf7c067ff]
[ 0.095427] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.095488] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500
[ 0.095507] pci 0000:00:1f.3: reg 0x10: [mem 0xf7c05000-0xf7c050ff 64bit]
[ 0.095526] pci 0000:00:1f.3: reg 0x20: [io 0xf040-0xf05f]
[ 0.095642] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.095717] pci 0000:02:00.0: [10ec:8136] type 00 class 0x020000
[ 0.095741] pci 0000:02:00.0: reg 0x10: [io 0xe000-0xe0ff]
[ 0.095775] pci 0000:02:00.0: reg 0x18: [mem 0xf0004000-0xf0004fff
64bit pref]
[ 0.095796] pci 0000:02:00.0: reg 0x20: [mem 0xf0000000-0xf0003fff
64bit pref]
[ 0.095888] pci 0000:02:00.0: supports D1 D2
[ 0.095889] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.098023] pci 0000:00:1c.2: PCI bridge to [bus 02]
[ 0.098033] pci 0000:00:1c.2: bridge window [io 0xe000-0xefff]
[ 0.098042] pci 0000:00:1c.2: bridge window [mem
0xf0000000-0xf00fffff 64bit pref]
[ 0.098071] pci_bus 0000:00: on NUMA node 0
[ 0.098356] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12
14 15)
[ 0.098402] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14
15) *0, disabled.
[ 0.098449] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 10 11 12
14 15)
[ 0.098492] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12
14 15)
[ 0.098535] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14
15) *0, disabled.
[ 0.098579] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14
15) *0, disabled.
[ 0.098624] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 10 11 12
14 15)
[ 0.098667] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12
14 15)
[ 0.098826] ACPI: Enabled 4 GPEs in block 00 to 3F
[ 0.098882] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[ 0.098882] pci 0000:00:02.0: vgaarb: VGA device added:
decodes=io+mem,owns=io+mem,locks=none
[ 0.098882] pci 0000:00:02.0: vgaarb: bridge control possible
[ 0.098882] vgaarb: loaded
[ 0.098882] SCSI subsystem initialized
[ 0.098882] libata version 3.00 loaded.
[ 0.099003] ACPI: bus type USB registered
[ 0.099021] usbcore: registered new interface driver usbfs
[ 0.099031] usbcore: registered new interface driver hub
[ 0.099041] usbcore: registered new device driver usb
[ 0.099055] EDAC MC: Ver: 3.0.0
[ 0.099111] PCI: Using ACPI for IRQ routing
[ 0.099111] PCI: pci_cache_line_size set to 64 bytes
[ 0.099111] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[ 0.099111] e820: reserve RAM buffer [mem 0x40004000-0x43ffffff]
[ 0.099111] e820: reserve RAM buffer [mem 0xcdf31000-0xcfffffff]
[ 0.099111] e820: reserve RAM buffer [mem 0xce6da000-0xcfffffff]
[ 0.099111] e820: reserve RAM buffer [mem 0xcee1a000-0xcfffffff]
[ 0.099111] e820: reserve RAM buffer [mem 0xcf000000-0xcfffffff]
[ 0.099111] e820: reserve RAM buffer [mem 0x21f600000-0x21fffffff]
[ 0.099133] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.099133] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.101009] clocksource: Switched to clocksource hpet
[ 0.106960] VFS: Disk quotas dquot_6.6.0
[ 0.106979] VFS: Dquot-cache hash table entries: 512 (order 0, 4096
bytes)
[ 0.107043] pnp: PnP ACPI init
[ 0.107135] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[ 0.107141] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.107200] system 00:01: [io 0x0680-0x069f] has been reserved
[ 0.107204] system 00:01: [io 0x0200-0x020f] has been reserved
[ 0.107208] system 00:01: [io 0xffff] has been reserved
[ 0.107211] system 00:01: [io 0xffff] has been reserved
[ 0.107215] system 00:01: [io 0x0400-0x0453] has been reserved
[ 0.107218] system 00:01: [io 0x0458-0x047f] has been reserved
[ 0.107222] system 00:01: [io 0x0500-0x057f] has been reserved
[ 0.107225] system 00:01: [io 0x164e-0x164f] has been reserved
[ 0.107230] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.107247] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.107280] system 00:03: [io 0x0454-0x0457] has been reserved
[ 0.107285] system 00:03: Plug and Play ACPI device, IDs INT3f0d
PNP0c02 (active)
[ 0.107344] system 00:04: [io 0x0a30-0x0a3f] has been reserved
[ 0.107349] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.107379] pnp 00:05: Plug and Play ACPI device, IDs PNP0303 PNP030b
(active)
[ 0.107490] pnp 00:06: [dma 0 disabled]
[ 0.107523] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.107556] system 00:07: [io 0x04d0-0x04d1] has been reserved
[ 0.107561] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.107713] system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.107718] system 00:08: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.107721] system 00:08: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.107725] system 00:08: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.107729] system 00:08: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.107733] system 00:08: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.107736] system 00:08: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.107740] system 00:08: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.107744] system 00:08: [mem 0xff000000-0xffffffff] has been reserved
[ 0.107748] system 00:08: [mem 0xfee00000-0xfeefffff] could not be
reserved
[ 0.107751] system 00:08: [mem 0xdfa00000-0xdfa00fff] has been reserved
[ 0.107756] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.107868] system 00:09: [mem 0x20000000-0x201fffff] has been reserved
[ 0.107872] system 00:09: [mem 0x40004000-0x40004fff] has been reserved
[ 0.107876] system 00:09: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.107893] pnp: PnP ACPI: found 10 devices
[ 0.113812] clocksource: acpi_pm: mask: 0xffffff max_cycles:
0xffffff, max_idle_ns: 2085701024 ns
[ 0.113839] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.113854] pci 0000:00:1c.2: PCI bridge to [bus 02]
[ 0.113859] pci 0000:00:1c.2: bridge window [io 0xe000-0xefff]
[ 0.113869] pci 0000:00:1c.2: bridge window [mem
0xf0000000-0xf00fffff 64bit pref]
[ 0.113880] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.113881] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.113882] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff
window]
[ 0.113883] pci_bus 0000:00: resource 7 [mem 0x000d4000-0x000d7fff
window]
[ 0.113884] pci_bus 0000:00: resource 8 [mem 0x000d8000-0x000dbfff
window]
[ 0.113885] pci_bus 0000:00: resource 9 [mem 0x000dc000-0x000dffff
window]
[ 0.113886] pci_bus 0000:00: resource 10 [mem 0x000e0000-0x000e3fff
window]
[ 0.113887] pci_bus 0000:00: resource 11 [mem 0x000e4000-0x000e7fff
window]
[ 0.113888] pci_bus 0000:00: resource 12 [mem 0xdfa00000-0xfeafffff
window]
[ 0.113889] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
[ 0.113890] pci_bus 0000:02: resource 2 [mem 0xf0000000-0xf00fffff
64bit pref]
[ 0.113961] NET: Registered protocol family 2
[ 0.114072] TCP established hash table entries: 65536 (order: 7,
524288 bytes)
[ 0.114174] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.114358] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.114387] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.114415] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.114472] NET: Registered protocol family 1
[ 0.114567] RPC: Registered named UNIX socket transport module.
[ 0.114571] RPC: Registered udp transport module.
[ 0.114574] RPC: Registered tcp transport module.
[ 0.114577] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.114591] pmd_set_huge: Cannot satisfy [mem 0xf7800000-0xf7a00000]
with a huge-page mapping due to MTRR override.
[ 0.114604] pci 0000:00:02.0: BIOS left Intel GPU interrupts enabled;
disabling
[ 0.114623] pci 0000:00:02.0: Video device with shadowed ROM at [mem
0x000c0000-0x000dffff]
[ 0.147118] PCI: CLS 64 bytes, default 64
[ 0.147154] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.147159] software IO TLB [mem 0xc9f31000-0xcdf31000] (64MB) mapped
at [ffff8800c9f31000-ffff8800cdf30fff]
[ 0.147224] RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters,
163840 ms ovfl timer
[ 0.147229] RAPL PMU: hw unit of domain pp0-core 2^-16 Joules
[ 0.147232] RAPL PMU: hw unit of domain package 2^-16 Joules
[ 0.147235] RAPL PMU: hw unit of domain pp1-gpu 2^-16 Joules
[ 0.147498] audit: initializing netlink subsys (disabled)
[ 0.147531] audit: type=2000 audit(1509198077.147:1):
state=initialized audit_enabled=0 res=1
[ 0.147672] workingset: timestamp_bits=46 max_order=21 bucket_order=0
[ 0.148714] NFS: Registering the id_resolver key type
[ 0.148722] Key type id_resolver registered
[ 0.148725] Key type id_legacy registered
[ 0.148729] Installing knfsd (copyright (C) 1996 [email protected]).
[ 0.148805] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.148833] romfs: ROMFS MTD (C) 2007 Red Hat, Inc.
[ 0.150277] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 252)
[ 0.150308] io scheduler noop registered
[ 0.150312] io scheduler deadline registered
[ 0.150332] io scheduler cfq registered (default)
[ 0.150336] io scheduler mq-deadline registered
[ 0.150338] io scheduler kyber registered
[ 0.150628] vesafb: mode is 1024x768x16, linelength=2048, pages=169
[ 0.150632] vesafb: scrolling: redraw
[ 0.150635] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 0.150648] vesafb: framebuffer at 0xe0000000, mapped to
0xffffc90000c00000, using 3072k, total 262080k
[ 0.175404] Console: switching to colour frame buffer device 128x48
[ 0.198195] fb0: VESA VGA frame buffer device
[ 0.198406] intel_idle: MWAIT substates: 0x1120
[ 0.198407] intel_idle: v0.4.1 model 0x3A
[ 0.198458] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.198516] GHES: HEST is not enabled!
[ 0.201105] brd: module loaded
[ 0.201400] fnic: Cisco FCoE HBA Driver, ver 1.6.0.34
[ 0.201649] fnic: Successfully Initialized Trace Buffer
[ 0.201917] fnic: Successfully Initialized FC_CTLR Trace Buffer
[ 0.202370] Adaptec aacraid driver 1.2.1[50834]-custom
[ 0.202617] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
[ 0.203058] scsi: <fdomain> Detection failed (no card)
[ 0.203308] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA
Driver: 10.00.00.00-k.
[ 0.203696] Emulex LightPulse Fibre Channel SCSI driver 11.4.0.1
[ 0.203974] Copyright (C) 2017 Broadcom. All Rights Reserved. The
term "Broadcom" refers to Broadcom Limited and/or its subsidiaries.
[ 0.204602] QLogic BR-series BFA FC/FCOE SCSI driver - version: 3.2.25.1
[ 0.204946] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03
EST 2006)
[ 0.205308] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST
2006)
[ 0.205637] megasas: 07.701.17.00-rc1
[ 0.205817] mpt3sas version 15.100.00.00 loaded
[ 0.215061] GDT-HA: Storage RAID Controller Driver. Version: 3.05
[ 0.224486] 3ware Storage Controller device driver for Linux
v1.26.02.003.
[ 0.233970] 3ware 9000 Storage Controller device driver for Linux
v2.26.02.014.
[ 0.243497] LSI 3ware SAS/SATA-RAID Controller device driver for
Linux v3.26.02.000.
[ 0.253038] ipr: IBM Power RAID SCSI Device Driver version: 2.6.4
(March 14, 2017)
[ 0.262591] RocketRAID 3xxx/4xxx Controller driver v1.10.0
[ 0.272060] stex: Promise SuperTrak EX Driver version: 6.02.0000.01
[ 0.281660] st: Version 20160209, fixed bufsize 32768, s/g segs 256
[ 0.291417] ahci 0000:00:1f.2: version 3.0
[ 0.291586] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 3 Gbps
0x3 impl SATA mode
[ 0.301477] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum
part ems apst
[ 0.314341] scsi host0: ahci
[ 0.324210] scsi host1: ahci
[ 0.333807] scsi host2: ahci
[ 0.343147] scsi host3: ahci
[ 0.352314] ata1: SATA max UDMA/133 abar m2048@0xf7c06000 port
0xf7c06100 irq 24
[ 0.361835] ata2: SATA max UDMA/133 abar m2048@0xf7c06000 port
0xf7c06180 irq 24
[ 0.371289] ata3: DUMMY
[ 0.380658] ata4: DUMMY
[ 0.390447] scsi host4: pata_legacy
[ 0.399711] ata5: PATA max PIO4 cmd 0x1f0 ctl 0x3f6 irq 14
[ 0.708584] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 0.718028] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 0.727308] ACPI Error: [DSSP] Namespace lookup failure, AE_NOT_FOUND
(20170531/psargs-364)
[ 0.736659] ACPI Error: Method parse/execution failed
\_SB.PCI0.SAT0.SPT1._GTF, AE_NOT_FOUND (20170531/psparse-550)
[ 0.746208] ata2.00: ATAPI: TSSTcorp CDDVDW SH-224BB, SB00, max UDMA/100
[ 0.755793] ACPI Error: [DSSP] Namespace lookup failure, AE_NOT_FOUND
(20170531/psargs-364)
[ 0.765646] ACPI Error: Method parse/execution failed
\_SB.PCI0.SAT0.SPT0._GTF, AE_NOT_FOUND (20170531/psparse-550)
[ 0.776076] ata1.00: ATA-8: ST500DM002-1BD142, KC45, max UDMA/133
[ 0.786335] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 0.796688] ACPI Error: [DSSP] Namespace lookup failure, AE_NOT_FOUND
(20170531/psargs-364)
[ 0.807332] ACPI Error: Method parse/execution failed
\_SB.PCI0.SAT0.SPT1._GTF, AE_NOT_FOUND (20170531/psparse-550)
[ 0.818223] ata2.00: configured for UDMA/100
[ 0.830011] ACPI Error: [DSSP] Namespace lookup failure, AE_NOT_FOUND
(20170531/psargs-364)
[ 0.841063] ACPI Error: Method parse/execution failed
\_SB.PCI0.SAT0.SPT0._GTF, AE_NOT_FOUND (20170531/psparse-550)
[ 0.852511] ata1.00: configured for UDMA/133
[ 1.183051] tsc: Refined TSC clocksource calibration: 2594.107 MHz
[ 1.194009] clocksource: tsc: mask: 0xffffffffffffffff max_cycles:
0x25647d583cf, max_idle_ns: 440795304232 ns
[ 2.207211] clocksource: Switched to clocksource tsc
[ 3.231176] floppy0: no floppy controllers found
[ 3.242200] scsi 0:0:0:0: Direct-Access ATA ST500DM002-1BD14
KC45 PQ: 0 ANSI: 5
[ 3.253340] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500
GB/466 GiB)
[ 3.264349] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 3.275325] sd 0:0:0:0: [sda] Write Protect is off
[ 3.275344] scsi 1:0:0:0: CD-ROM TSSTcorp CDDVDW SH-224BB
SB00 PQ: 0 ANSI: 5
[ 3.297181] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.297192] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 3.311966] sr 1:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer dvd-ram
cd/rw xa/form2 cdda tray
[ 3.323070] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 3.334137] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 3.359230] sda: sda1 sda2 sda3 sda5 sda6
[ 3.370454] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.381610] scsi host4: pata_legacy
[ 3.392321] ata6: PATA max PIO4 cmd 0x170 ctl 0x376 irq 15
[ 3.559205] Fusion MPT base driver 3.04.20
[ 3.569748] Copyright (c) 1999-2008 LSI Corporation
[ 3.580254] Fusion MPT SPI Host driver 3.04.20
[ 3.590910] Fusion MPT FC Host driver 3.04.20
[ 3.601639] Fusion MPT SAS Host driver 3.04.20
[ 3.612472] Fusion MPT misc device (ioctl) driver 3.04.20
[ 3.623273] mptctl: Registered with Fusion MPT base driver
[ 3.634203] mptctl: /dev/mptctl @ (major,minor=10,220)
[ 3.645038] Fusion MPT LAN driver 3.04.20
[ 3.656033] usbcore: registered new interface driver usbserial
[ 3.667160] usbcore: registered new interface driver usbserial_generic
[ 3.678186] usbserial: USB Serial support registered for generic
[ 3.689233] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 3.700518] i8042: PNP: PS/2 appears to have AUX port disabled, if
this is incorrect please boot with i8042.nopnp
[ 3.712525] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.723830] mousedev: PS/2 mouse device common for all mice
[ 3.734880] rtc_cmos 00:02: RTC can wake from S4
[ 3.745867] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 3.756576] rtc_cmos 00:02: alarms up to one month, y3k, 242 bytes
nvram, hpet irqs
[ 3.767145] intel_pstate: Intel P-state driver initializing
[ 3.777828] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.794020] Initializing XFRM netlink socket
[ 3.809826] NET: Registered protocol family 17
[ 3.819749] Key type dns_resolver registered
[ 3.829606] microcode: sig=0x306a9, pf=0x2, revision=0x10
[ 3.839209] microcode: Microcode Update Driver: v2.2.
[ 3.839217] sched_clock: Marking stable (3839205490, 0)->(3839677294,
-471804)
[ 3.857943] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input0
[ 3.858084] registered taskstats version 1
[ 3.898324] EXT4-fs (sda2): couldn't mount as ext3 due to feature
incompatibilities
[ 3.942183] EXT4-fs (sda2): mounted filesystem with ordered data
mode. Opts: (null)
[ 3.951626] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[ 3.979748] devtmpfs: mounted
[ 3.990553] Freeing unused kernel memory: 1440K
[ 4.000585] Write protecting the kernel read-only data: 14336k
[ 4.010209] Freeing unused kernel memory: 616K
[ 4.021513] Freeing unused kernel memory: 1084K
[ 4.030416] rodata_test: all tests were successful
[ 4.678967] random: crng init done
[ 5.435789] udevd[153]: bind failed: Read-only file system
[ 5.444612] udevd[153]: error binding udev control socket
[ 5.585045] Adding 16787920k swap on /dev/sda3. Priority:-1
extents:1 across:16787920k
[ 5.948565] fuse init (API version 7.26)
[ 6.354334] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 6.396835] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 10.022320] EXT4-fs (sda5): mounted filesystem with ordered data
mode. Opts: (null)
[ 10.177325] EXT4-fs (sda6): mounted filesystem with ordered data
mode. Opts: (null)
[ 10.272131] EXT4-fs (sda1): mounted filesystem with ordered data
mode. Opts: (null)
[ 16.658346] udevd[528]: starting eudev-3.2.4
[ 17.426432] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
[ 17.451676] input: Power Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 17.451692] ACPI: Power Button [PWRB]
[ 17.451724] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 17.451731] ACPI: Power Button [PWRF]
[ 17.490100] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 17.497283] ACPI Warning: SystemIO range
0x0000000000000428-0x000000000000042F conflicts with OpRegion
0x0000000000000400-0x000000000000047F (\PMIO) (20170531/utaddress-247)
[ 17.497288] ACPI: If an ACPI driver is available for this device, you
should use it instead of the native driver
[ 17.497290] ACPI Warning: SystemIO range
0x0000000000000540-0x000000000000054F conflicts with OpRegion
0x0000000000000500-0x0000000000000563 (\GPIO) (20170531/utaddress-247)
[ 17.497293] ACPI: If an ACPI driver is available for this device, you
should use it instead of the native driver
[ 17.497293] ACPI Warning: SystemIO range
0x0000000000000530-0x000000000000053F conflicts with OpRegion
0x0000000000000500-0x0000000000000563 (\GPIO) (20170531/utaddress-247)
[ 17.497295] ACPI: If an ACPI driver is available for this device, you
should use it instead of the native driver
[ 17.497296] ACPI Warning: SystemIO range
0x0000000000000500-0x000000000000052F conflicts with OpRegion
0x0000000000000500-0x0000000000000563 (\GPIO) (20170531/utaddress-247)
[ 17.497298] ACPI: If an ACPI driver is available for this device, you
should use it instead of the native driver
[ 17.497298] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 17.521285] ehci-pci: EHCI PCI platform driver
[ 17.521436] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 17.521495] ehci-pci 0000:00:1a.0: new USB bus registered, assigned
bus number 1
[ 17.521508] ehci-pci 0000:00:1a.0: debug port 2
[ 17.525423] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[ 17.525649] ehci-pci 0000:00:1a.0: irq 16, io mem 0xf7c08000
[ 17.532017] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 17.532076] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 17.532077] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 17.532079] usb usb1: Product: EHCI Host Controller
[ 17.532081] usb usb1: Manufacturer: Linux 4.13.8.20171019 ehci_hcd
[ 17.532082] usb usb1: SerialNumber: 0000:00:1a.0
[ 17.532272] hub 1-0:1.0: USB hub found
[ 17.532277] hub 1-0:1.0: 2 ports detected
[ 17.532480] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 17.532513] ehci-pci 0000:00:1d.0: new USB bus registered, assigned
bus number 2
[ 17.532524] ehci-pci 0000:00:1d.0: debug port 2
[ 17.536411] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 17.536717] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7c07000
[ 17.543013] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 17.543066] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 17.543068] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 17.543069] usb usb2: Product: EHCI Host Controller
[ 17.543071] usb usb2: Manufacturer: Linux 4.13.8.20171019 ehci_hcd
[ 17.543072] usb usb2: SerialNumber: 0000:00:1d.0
[ 17.543195] hub 2-0:1.0: USB hub found
[ 17.543200] hub 2-0:1.0: 2 ports detected
[ 17.566079] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 17.586680] 00:06: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200)
is a 16550A
[ 17.622449] Linux agpgart interface v0.103
[ 17.634429] thermal LNXTHERM:00: registered as thermal_zone0
[ 17.634430] ACPI: Thermal Zone [TZ00] (28 C)
[ 17.634597] thermal LNXTHERM:01: registered as thermal_zone1
[ 17.634597] ACPI: Thermal Zone [TZ01] (30 C)
[ 17.772416] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 17.772763] r8169 0000:02:00.0 eth0: RTL8105e at 0xffffc90000049000,
00:e0:66:84:16:a7, XID 00a00000 IRQ 26
[ 17.847016] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 17.855013] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 17.965317] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[ 17.965320] usb 1-1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 17.965592] hub 1-1:1.0: USB hub found
[ 17.965685] hub 1-1:1.0: 4 ports detected
[ 17.973314] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[ 17.973316] usb 2-1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 17.973464] hub 2-1:1.0: USB hub found
[ 17.973560] hub 2-1:1.0: 6 ports detected
[ 18.239015] usb 1-1.2: new full-speed USB device number 3 using ehci-pci
[ 18.248021] usb 2-1.3: new low-speed USB device number 3 using ehci-pci
[ 18.260473] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 18.330184] usb 2-1.3: New USB device found, idVendor=093a,
idProduct=2510
[ 18.330185] usb 2-1.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 18.330187] usb 2-1.3: Product: USB OPTICAL MOUSE
[ 18.330188] usb 2-1.3: Manufacturer: PIXART
[ 18.347995] i2c /dev entries driver
[ 18.880809] usb 1-1.2: New USB device found, idVendor=1b3f,
idProduct=2007
[ 18.880812] usb 1-1.2: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 18.880813] usb 1-1.2: Product: USB Audio Device
[ 18.880815] usb 1-1.2: Manufacturer: GeneralPlus
[ 19.322316] [drm] Memory usable by graphics device = 2048M
[ 19.322319] checking generic (e0000000 fff0000) vs hw (e0000000 10000000)
[ 19.322319] fb: switching to inteldrmfb from VESA VGA
[ 19.322355] Console: switching to colour dummy device 80x25
[ 19.322424] [drm] Replacing VGA console driver
[ 19.328065] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 19.328066] [drm] Driver supports precise vblank timestamp query.
[ 19.330582] i915 0000:00:02.0: vgaarb: changed VGA decodes:
olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 19.334551] [drm] Initialized i915 1.6.0 20170619 for 0000:00:02.0 on
minor 0
[ 19.335036] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 19.335297] acpi device:49: registered as cooling_device8
[ 19.335554] input: Video Bus as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input4
[ 19.352187] snd_hda_intel 0000:00:1b.0: bound 0000:00:02.0 (ops
i915_audio_component_bind_ops [i915])
[ 19.398703] fbcon: inteldrmfb (fb0) is primary device
[ 19.458096] Console: switching to colour frame buffer device 170x48
[ 19.476705] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 19.899223] snd_hda_codec_realtek hdaudioC0D2: autoconfig for ALC662
rev3: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[ 19.899224] snd_hda_codec_realtek hdaudioC0D2: speaker_outs=0
(0x0/0x0/0x0/0x0/0x0)
[ 19.899225] snd_hda_codec_realtek hdaudioC0D2: hp_outs=1
(0x1b/0x0/0x0/0x0/0x0)
[ 19.899226] snd_hda_codec_realtek hdaudioC0D2: mono: mono_out=0x0
[ 19.899227] snd_hda_codec_realtek hdaudioC0D2: dig-out=0x1e/0x0
[ 19.899228] snd_hda_codec_realtek hdaudioC0D2: inputs:
[ 19.899229] snd_hda_codec_realtek hdaudioC0D2: Front Mic=0x19
[ 19.899230] snd_hda_codec_realtek hdaudioC0D2: Rear Mic=0x18
[ 19.899231] snd_hda_codec_realtek hdaudioC0D2: Line=0x1a
[ 20.285745] input: HDA Intel PCH Front Mic as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[ 20.285799] input: HDA Intel PCH Rear Mic as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[ 20.285846] input: HDA Intel PCH Line as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 20.285892] input: HDA Intel PCH Line Out as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 20.285936] input: HDA Intel PCH Front Headphone as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 20.285982] input: HDA Intel PCH HDMI/DP,pcm=3 as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 20.286036] input: HDA Intel PCH HDMI/DP,pcm=7 as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 20.286184] input: HDA Intel PCH HDMI/DP,pcm=8 as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[ 21.608466] hidraw: raw HID events driver (C) Jiri Kosina
[ 21.635340] usbcore: registered new interface driver usbhid
[ 21.635341] usbhid: USB HID core driver
[ 21.739682] usbcore: registered new interface driver snd-usb-audio
[ 23.159597] input: PIXART USB OPTICAL MOUSE as
/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/0003:093A:2510.0001/input/input13
[ 23.159690] hid-generic 0003:093A:2510.0001: input,hidraw0: USB HID
v1.11 Mouse [PIXART USB OPTICAL MOUSE] on usb-0000:00:1d.0-1.3/input0
[ 23.159786] input: GeneralPlus USB Audio Device as
/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.3/0003:1B3F:2007.0002/input/input14
[ 23.211240] hid-generic 0003:1B3F:2007.0002: input,hidraw1: USB HID
v2.01 Device [GeneralPlus USB Audio Device] on usb-0000:00:1a.0-1.2/input3
[ 24.217048] r8169 0000:02:00.0 eth0: link down
[ 24.217062] r8169 0000:02:00.0 eth0: link down
[ 24.502121] NET: Registered protocol family 10
[ 24.502362] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 24.502403] Segment Routing with IPv6
[ 25.615236] NFSD: the nfsdcld client tracking upcall will be removed
in 3.10. Please transition to using nfsdcltrack.
[ 25.615239] NFSD: starting 90-second grace period (net ffffffff81ee6400)
[ 25.818487] r8169 0000:02:00.0 eth0: link up
[ 25.818500] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 37.455802] nct6775: Found NCT6779D or compatible chip at 0x2e:0xa30
[ 37.737820] NET: Registered protocol family 4
[ 37.749316] NET: Registered protocol family 5
[ 145.887027] NFSD: Unable to end grace period: -110
[ 145.966016] usb 2-1.4: new high-speed USB device number 4 using ehci-pci
[ 146.045808] usb 2-1.4: New USB device found, idVendor=0bda,
idProduct=8178
[ 146.045811] usb 2-1.4: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 146.045812] usb 2-1.4: Product: 802.11n WLAN Adapter
[ 146.045813] usb 2-1.4: Manufacturer: Realtek
[ 146.045814] usb 2-1.4: SerialNumber: 00e04c000001
[ 146.202043] rtl8192cu: Chip version 0x11
[ 146.278549] rtl8192cu: Board Type 0
[ 146.278790] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[ 146.278823] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
[ 146.278938] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 146.279113] usbcore: registered new interface driver rtl8192cu
[ 146.281706] usbcore: registered new interface driver rtl8xxxu
[ 146.344941] rtl8192cu 2-1.4:1.0 wlan125: renamed from wlan0
[ 146.348126] rtl8192cu 2-1.4:1.0 wlan1: renamed from wlan125
[ 187.045383] rtl8192cu: MAC auto ON okay!
[ 187.079138] rtl8192cu: Tx queue select: 0x05
[ 187.678428] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 190.424743] rtl8192cu: MAC auto ON okay!
[ 190.457904] rtl8192cu: Tx queue select: 0x05
[ 191.067336] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 191.192858] rtl8192cu: MAC auto ON okay!
[ 191.225864] rtl8192cu: Tx queue select: 0x05
[ 191.834651] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 193.861920] wlan1: authenticate with 34:e0:cf:f2:e2:18
[ 193.873285] wlan1: send auth to 34:e0:cf:f2:e2:18 (try 1/3)
[ 193.877329] wlan1: aborting authentication with 34:e0:cf:f2:e2:18 by
local choice (Reason: 3=DEAUTH_LEAVING)
[ 193.889626] wlan1: authenticate with 34:e0:cf:f2:e2:18
[ 193.905124] wlan1: send auth to 34:e0:cf:f2:e2:18 (try 1/3)
[ 193.908920] wlan1: aborting authentication with 34:e0:cf:f2:e2:18 by
local choice (Reason: 3=DEAUTH_LEAVING)
[ 193.921612] wlan1: authenticate with 34:e0:cf:f2:e2:18
[ 193.934649] wlan1: send auth to 34:e0:cf:f2:e2:18 (try 1/3)
[ 193.934694] wlan1: authenticated
[ 193.935963] wlan1: associate with 34:e0:cf:f2:e2:18 (try 1/3)
[ 193.991609] wlan1: RX AssocResp from 34:e0:cf:f2:e2:18 (capab=0x421
status=0 aid=2)
[ 194.093600] wlan1: associated
[ 194.095031] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
--
nirinA
On Sun, Oct 29, 2017 at 01:08:24AM +0300, nirinA raseliarison wrote:
> [ 145.966016] usb 2-1.4: new high-speed USB device number 4 using ehci-pci
> [ 146.045808] usb 2-1.4: New USB device found, idVendor=0bda,
> idProduct=8178
> [ 146.045811] usb 2-1.4: New USB device strings: Mfr=1, Product=2,
> SerialNumber=3
> [ 146.045812] usb 2-1.4: Product: 802.11n WLAN Adapter
> [ 146.045813] usb 2-1.4: Manufacturer: Realtek
> [ 146.045814] usb 2-1.4: SerialNumber: 00e04c000001
> [ 146.202043] rtl8192cu: Chip version 0x11
> [ 146.278549] rtl8192cu: Board Type 0
> [ 146.278790] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
> [ 146.278823] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
> [ 146.278938] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
> [ 146.279113] usbcore: registered new interface driver rtl8192cu
> [ 146.281706] usbcore: registered new interface driver rtl8xxxu
> --
> nirinA
It appears that both rtl8192cu and rtl8xxxu are being loaded for the
one device.
Try blacklisting one of them.
Barry
On 10/18/2017 08:40 PM, nirinA wrote:
> i checked my dmesg and have this similar log, i think when i unplugged the device.
>
> [ 5640.100541] usb 2-1.4: USB disconnect, device number 5
> [ 5640.104108] rtl_usb: reg 0x102, usbctrl_vendorreq TimeOut! status:0xffffffed
> value=0x0
> [ 5640.104110] rtl_usb: reg 0x422, usbctrl_vendorreq TimeOut! status:0xffffffed
> value=0x0
> [ 5640.104113] rtl_usb: reg 0x542, usbctrl_vendorreq TimeOut! status:0xffffffed
> value=0x0
> [ 5640.104127] rtl_usb: reg 0x102, usbctrl_vendorreq TimeOut! status:0xffffffed
> value=0xd38000
>
> i will apply the patch and will see if i still get this.
As I said in the response to your private message:
No, that is a different error. You need to check for the USB disconnect when
starting, but no rtl_usb errors.
Larry
hi all,
i applied the patch against 4.13.8. i still got some trouble, dmesg is
below.
after i plugged the device, it seems to be detected and all modules loaded,
but when i tried to connect to an access point, by using wicd, it halted
after
a while. at this point, all usb ports are broken, there was no more log
in dmesg,
lsusb still showed the device even after being unplugged. it got even
worse as
reboot failed.
i cannot really trace the error as right now all thing works fine.
##
[101297.211119] usb 2-1.4: new high-speed USB device number 6 using ehci-pci
[101297.290836] usb 2-1.4: New USB device found, idVendor=0bda,
idProduct=8178
[101297.290839] usb 2-1.4: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[101297.290840] usb 2-1.4: Product: 802.11n WLAN Adapter
[101297.290841] usb 2-1.4: Manufacturer: Realtek
[101297.290842] usb 2-1.4: SerialNumber: 00e04c000001
[101297.841845] rtl8192cu: Chip version 0x11
[101297.973333] rtl8192cu: Board Type 0
[101297.973581] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[101297.973621] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
[101297.973743] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[101297.973923] usbcore: registered new interface driver rtl8192cu
[101298.013513] usbcore: registered new interface driver rtl8xxxu
[101298.113014] rtl8192cu 2-1.4:1.0 wlan125: renamed from wlan0
[101298.116255] rtl8192cu 2-1.4:1.0 wlan4: renamed from wlan125
[101298.319580] usb 2-1.4: USB disconnect, device number 6
[101298.508120] usb 2-1.4: new high-speed USB device number 7 using ehci-pci
[101298.748134] usb 2-1.4: new high-speed USB device number 8 using ehci-pci
[101298.827700] usb 2-1.4: New USB device found, idVendor=0bda,
idProduct=8178
[101298.827702] usb 2-1.4: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[101298.827703] usb 2-1.4: Product: 802.11n WLAN Adapter
[101298.827704] usb 2-1.4: Manufacturer: Realtek
[101298.827705] usb 2-1.4: SerialNumber: 00e04c000001
[101298.828320] rtl8192cu: Chip version 0x11
[101298.907705] rtl8192cu: Board Type 0
[101298.907945] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[101298.907976] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
[101298.908145] ieee80211 phy1: Selected rate control algorithm 'rtl_rc'
[101298.922774] rtl8192cu 2-1.4:1.0 wlan124: renamed from wlan0
[101298.926242] rtl8192cu 2-1.4:1.0 wlan4: renamed from wlan124
[101312.904723] rtl8192cu: MAC auto ON okay!
[101312.939101] rtl8192cu: Tx queue select: 0x05
[101313.541630] IPv6: ADDRCONF(NETDEV_UP): wlan4: link is not ready
[101322.297910] rtl8192cu: MAC auto ON okay!
[101322.331036] rtl8192cu: Tx queue select: 0x05
[101322.933065] IPv6: ADDRCONF(NETDEV_UP): wlan4: link is not ready
[101323.089905] rtl8192cu: MAC auto ON okay!
[101323.122907] rtl8192cu: Tx queue select: 0x05
[101323.730181] IPv6: ADDRCONF(NETDEV_UP): wlan4: link is not ready
[101325.455267] usb 2-1.4: USB disconnect, device number 8
[101325.460166] rtl_usb: reg 0x102, usbctrl_vendorreq TimeOut!
status:0xffffffed value=0xf90000
[101325.460168] rtl_usb: reg 0x422, usbctrl_vendorreq TimeOut!
status:0xffffffed value=0x1000000
[101325.460171] rtl_usb: reg 0x542, usbctrl_vendorreq TimeOut!
status:0xffffffed value=0x3fd0000
[101325.460186] rtl_usb: reg 0x102, usbctrl_vendorreq TimeOut!
status:0xffffffed value=0xf90000
[101325.655146] usb 2-1.4: new high-speed USB device number 9 using ehci-pci
[101325.734893] usb 2-1.4: New USB device found, idVendor=0bda,
idProduct=8178
[101325.734897] usb 2-1.4: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[101325.734898] usb 2-1.4: Product: 802.11n WLAN Adapter
[101325.734899] usb 2-1.4: Manufacturer: Realtek
[101325.734900] usb 2-1.4: SerialNumber: 00e04c000001
[101325.735636] rtl8192cu: Chip version 0x11
[101325.812035] rtl8192cu: Board Type 0
[101325.812394] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[101325.812470] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
[101325.812725] ieee80211 phy2: Selected rate control algorithm 'rtl_rc'
[101325.827120] rtl8192cu 2-1.4:1.0 wlan123: renamed from wlan0
[101325.832254] rtl8192cu 2-1.4:1.0 wlan4: renamed from wlan123
[101332.879463] usb 2-1.4: USB disconnect, device number 9
[101333.072149] usb 2-1.4: new high-speed USB device number 10 using
ehci-pci
[101333.151841] usb 2-1.4: New USB device found, idVendor=0bda,
idProduct=8178
[101333.151843] usb 2-1.4: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[101333.151845] usb 2-1.4: Product: 802.11n WLAN Adapter
[101333.151846] usb 2-1.4: Manufacturer: Realtek
[101333.151847] usb 2-1.4: SerialNumber: 00e04c000001
[101333.152585] rtl8192cu: Chip version 0x11
[101333.229738] rtl8192cu: Board Type 0
[101333.229963] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[101333.230038] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
[101333.230298] ieee80211 phy3: Selected rate control algorithm 'rtl_rc'
[101333.491111] rtl8192cu 2-1.4:1.0 wlan122: renamed from wlan0
[101333.496349] rtl8192cu 2-1.4:1.0 wlan4: renamed from wlan122
[101334.226575] rtl8192cu: MAC auto ON okay!
[101334.260084] rtl8192cu: Tx queue select: 0x05
[101334.859863] IPv6: ADDRCONF(NETDEV_UP): wlan4: link is not ready
[101335.962440] wlan4: authenticate with 16:6b:72:6d:9d:fc
[101335.986731] wlan4: send auth to 16:6b:72:6d:9d:fc (try 1/3)
[101335.990957] wlan4: authenticated
[101335.991154] wlan4: associate with 16:6b:72:6d:9d:fc (try 1/3)
[101336.001221] wlan4: RX AssocResp from 16:6b:72:6d:9d:fc (capab=0x431
status=0 aid=1)
[101336.103329] wlan4: associated
[101336.103374] IPv6: ADDRCONF(NETDEV_CHANGE): wlan4: link becomes ready
[101340.303166] usb 2-1.4: USB disconnect, device number 10
[101340.307127] wlan4: deauthenticating from 16:6b:72:6d:9d:fc by local
choice (Reason: 3=DEAUTH_LEAVING)
[101340.512116] usb 2-1.4: new high-speed USB device number 11 using
ehci-pci
[101340.591917] usb 2-1.4: New USB device found, idVendor=0bda,
idProduct=8178
[101340.591919] usb 2-1.4: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[101340.591920] usb 2-1.4: Product: 802.11n WLAN Adapter
[101340.591921] usb 2-1.4: Manufacturer: Realtek
[101340.591922] usb 2-1.4: SerialNumber: 00e04c000001
[101340.592659] rtl8192cu: Chip version 0x11
[101340.674039] rtl8192cu: Board Type 0
[101340.674283] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[101340.674313] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
[101340.674430] ieee80211 phy4: Selected rate control algorithm 'rtl_rc'
[101340.684805] rtl8192cu 2-1.4:1.0 wlan121: renamed from wlan0
[101340.689245] rtl8192cu 2-1.4:1.0 wlan4: renamed from wlan121
[101340.695908] rtl8192cu: MAC auto ON okay!
[101340.735041] rtl8192cu: Tx queue select: 0x05
[101341.500551] rtl8192c_common: Polling FW ready fail!
REG_MCUFWDL:0x00030006.
[101341.500552] rtl8192c_common: Firmware is not ready to run!
[101341.855695] IPv6: ADDRCONF(NETDEV_UP): wlan4: link is not ready
[101342.201571] rtl8192cu: 8051 reset failed!.........................
[101343.273517] rtl8192cu: MAC auto ON okay!
[101343.306265] rtl8192cu: Tx queue select: 0x05
[101343.917002] IPv6: ADDRCONF(NETDEV_UP): wlan4: link is not ready
[101347.486500] rtl8192cu: MAC auto ON okay!
[101348.239112] usb 2-1.4: USB disconnect, device number 11
[101348.240514] rtl8192cu: Tx queue select: 0x05
##
--
nirinA
Larry Finger wrote:
> On 10/18/2017 08:40 PM, nirinA wrote:
>> i checked my dmesg and have this similar log, i think when i
>> unplugged the device.
>>
>> [ 5640.100541] usb 2-1.4: USB disconnect, device number 5
>> [ 5640.104108] rtl_usb: reg 0x102, usbctrl_vendorreq TimeOut!
>> status:0xffffffed value=0x0
>> [ 5640.104110] rtl_usb: reg 0x422, usbctrl_vendorreq TimeOut!
>> status:0xffffffed value=0x0
>> [ 5640.104113] rtl_usb: reg 0x542, usbctrl_vendorreq TimeOut!
>> status:0xffffffed value=0x0
>> [ 5640.104127] rtl_usb: reg 0x102, usbctrl_vendorreq TimeOut!
>> status:0xffffffed value=0xd38000
>>
>> i will apply the patch and will see if i still get this.
>
> As I said in the response to your private message:
sorry for the private mail, i press reply button instead of reply-all.
> No, that is a different error. You need to check for the USB
> disconnect when starting, but no rtl_usb errors.
>
up to now, i have no error when plugging the device with the same
machine. the message above only appears from time to time, not always
when i unplugged.
i also use 2 other rtl8192cu with a raspberry pi and a beaglebone black,
but never checked any log when the connection with the devices failed; i
just shut down and restart. i'll try to get more detail if some failure
will occur with these devices.
> Larry
>
thanks,
---
nirinA
On Thu, Oct 19, 2017 at 01:31:43AM +0300, nirinA wrote:
> hello there,
> i got the oops below with a rtl8192cu:0bda:8178 and kernel 4.13.6, but
> cannot reproduce it.
> i use this device since 4.3 or so without noticing any issue.
>
> nirinA
>
> [ 239.338040] usb 2-1.3: new high-speed USB device number 4 using ehci-pci
> [ 239.417728] usb 2-1.3: New USB device found, idVendor=0bda,
> idProduct=8178
> [ 239.417730] usb 2-1.3: New USB device strings: Mfr=1, Product=2,
> SerialNumber=3
> [ 239.417731] usb 2-1.3: Product: 802.11n WLAN Adapter
> [ 239.417732] usb 2-1.3: Manufacturer: Realtek
> [ 239.417733] usb 2-1.3: SerialNumber: 00e04c000001
> [ 239.578100] rtl8192cu: Chip version 0x11
> [ 239.678225] usb 2-1-port3: disabled by hub (EMI?), re-enabling...
Just prior to the oops, your USB hub disabled the port being used by
the wireless device.
While the response of the driver seems wrong, it is a difficult
condition to reproduce; one must either force or forge the disabling
by the hub.
> [ 239.678230] usb 2-1.3: USB disconnect, device number 4
> [ 239.679128] rtl_usb: reg 0x30, usbctrl_vendorreq TimeOut!
> status:0xffffffed value=0x0
> [ 239.679131] rtl_usb: reg 0x32, usbctrl_vendorreq TimeOut!
> status:0xffffffed value=0x20
> [ 239.679133] rtl_usb: reg 0x33, usbctrl_vendorreq TimeOut!
> status:0xffffffed value=0x80
> [ 239.679134] rtl_usb: reg 0x30, usbctrl_vendorreq TimeOut!
> status:0xffffffed value=0x80206f30
> [ 239.700640] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
> [ 239.700648] BUG: unable to handle kernel NULL pointer dereference at
> (null)
> [ 239.700682] IP: rtl_deinit_core+0x2e/0x90 [rtlwifi]
> [ 239.700693] PGD 1c5d5d067
> [ 239.700694] P4D 1c5d5d067
> [ 239.700701] PUD 1c5d9b067
> [ 239.700708] PMD 0
>
> [ 239.700727] Oops: 0000 [#1] SMP
> [ 239.700735] Modules linked in: rtl8192cu(+) rtl_usb rtl8192c_common
> rtlwifi mac80211 cfg80211 rfkill appletalk ipx p8023 p8022 psnap llc nct6775
> hwmon_vid ipv6 hid_generic usbhid hid coretemp hwmon x86_pkg_temp_thermal
> intel_powerclamp snd_hda_codec_hdmi snd_hda_codec_realtek
> snd_hda_codec_generic kvm_intel i915 kvm drm_kms_helper evdev i2c_dev
> irqbypass syscopyarea sysfillrect sysimgblt r8169 crc32_pclmul serio_raw
> crc32c_intel mii snd_pcsp fb_sys_fops drm fan thermal button battery 8250
> 8250_base serial_core mei_me snd_hda_intel mei intel_gtt snd_hda_codec video
> agpgart ehci_pci ehci_hcd lpc_ich snd_hwdep snd_hda_core snd_pcm
> i2c_algo_bit snd_timer i2c_i801 i2c_core snd soundcore fuse
> [ 239.700875] CPU: 0 PID: 1174 Comm: udevd Not tainted 4.13.6.20171012 #1
> [ 239.700889] Hardware name: To be filled by O.E.M. To be filled by
> O.E.M./ONDA H61V Ver:4.01, BIOS 4.6.5 01/07/2013
> [ 239.700909] task: ffff8801c5fbc980 task.stack: ffffc900009a0000
> [ 239.700924] RIP: 0010:rtl_deinit_core+0x2e/0x90 [rtlwifi]
> [ 239.700936] RSP: 0000:ffffc900009a3b40 EFLAGS: 00010207
> [ 239.700947] RAX: 0000000000000282 RBX: ffff8801b9440780 RCX:
> 00000000ffffffea
> [ 239.700962] RDX: 0000000000000001 RSI: 0000000000000282 RDI:
> 0000000000000000
> [ 239.700977] RBP: ffff8801b944b070 R08: 0000000000000001 R09:
> 00000000000002b0
> [ 239.700991] R10: ffffea0008473480 R11: 0000000000000000 R12:
> ffff8801b9441560
> [ 239.701006] R13: ffff8801b944b880 R14: 0000000000000000 R15:
> ffff8801b9441560
> [ 239.701021] FS: 00007f3eb636e7c0(0000) GS:ffff88021f200000(0000)
> knlGS:0000000000000000
> [ 239.701037] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
> [ 239.701050] CR2: 0000000000000000 CR3: 00000001c5d99000 CR4:
> 00000000001406f0
> [ 239.701064] Call Trace:
> [ 239.701074] ? rtl_usb_probe+0x6b6/0xc50 [rtl_usb]
> [ 239.701088] ? usb_probe_interface+0xe2/0x2a0
> [ 239.701100] ? driver_probe_device+0x21d/0x2d0
> [ 239.701111] ? __driver_attach+0x8a/0x90
> [ 239.701121] ? driver_probe_device+0x2d0/0x2d0
> [ 239.701133] ? bus_for_each_dev+0x5c/0x90
> [ 239.701143] ? bus_add_driver+0x196/0x220
> [ 239.701154] ? driver_register+0x57/0xc0
> [ 239.701165] ? usb_register_driver+0x7c/0x140
> [ 239.701175] ? 0xffffffffa064e000
> [ 239.701185] ? do_one_initcall+0x4b/0x190
> [ 239.701197] ? kmem_cache_alloc_trace+0xe4/0x1c0
> [ 239.701208] ? do_init_module+0x22/0x1e1
> [ 239.701219] ? do_init_module+0x5b/0x1e1
> [ 239.701229] ? load_module+0x21ff/0x2760
> [ 239.701239] ? SYSC_finit_module+0x90/0xb0
> [ 239.701249] ? SYSC_finit_module+0x90/0xb0
> [ 239.701261] ? entry_SYSCALL_64_fastpath+0x1a/0xa5
> [ 239.701272] Code: 00 00 41 57 31 f6 41 56 41 55 41 54 55 53 48 89 fb e8
> e7 fe ff ff 4c 8b 7b 48 49 8b bf 10 9b 00 00 49 8d af 10 9b 00 00 48 39 ef
> <48> 8b 1f 74 44 49 bd 00 01 00 00 00 00 ad de 49 89 de 49 bc 00
> [ 239.701327] RIP: rtl_deinit_core+0x2e/0x90 [rtlwifi] RSP:
> ffffc900009a3b40
> [ 239.702028] CR2: 0000000000000000
> [ 239.705370] ---[ end trace 6ec9029c0d9c0e13 ]---
> [ 239.706311] udevd[528]: worker [1174] failed while handling
> '/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0'
>
--
James Cameron
http://quozl.netrek.org/
not really a rtlwifi oops then. maybe issue with udev as that also
disabled the usb mouse.
but i have no problem since. i will report if i will catch it again.
thanks,
--
nirinA
James Cameron wrote:
> On Thu, Oct 19, 2017 at 01:31:43AM +0300, nirinA wrote:
>> hello there,
>> i got the oops below with a rtl8192cu:0bda:8178 and kernel 4.13.6, but
>> cannot reproduce it.
>> i use this device since 4.3 or so without noticing any issue.
>>
>> nirinA
>>
>> [ 239.338040] usb 2-1.3: new high-speed USB device number 4 using ehci-pci
>> [ 239.417728] usb 2-1.3: New USB device found, idVendor=0bda,
>> idProduct=8178
>> [ 239.417730] usb 2-1.3: New USB device strings: Mfr=1, Product=2,
>> SerialNumber=3
>> [ 239.417731] usb 2-1.3: Product: 802.11n WLAN Adapter
>> [ 239.417732] usb 2-1.3: Manufacturer: Realtek
>> [ 239.417733] usb 2-1.3: SerialNumber: 00e04c000001
>> [ 239.578100] rtl8192cu: Chip version 0x11
>> [ 239.678225] usb 2-1-port3: disabled by hub (EMI?), re-enabling...
> Just prior to the oops, your USB hub disabled the port being used by
> the wireless device.
>
> While the response of the driver seems wrong, it is a difficult
> condition to reproduce; one must either force or forge the disabling
> by the hub.
>
>> [ 239.678230] usb 2-1.3: USB disconnect, device number 4
>> [ 239.679128] rtl_usb: reg 0x30, usbctrl_vendorreq TimeOut!
>> status:0xffffffed value=0x0
>> [ 239.679131] rtl_usb: reg 0x32, usbctrl_vendorreq TimeOut!
>> status:0xffffffed value=0x20
>> [ 239.679133] rtl_usb: reg 0x33, usbctrl_vendorreq TimeOut!
>> status:0xffffffed value=0x80
>> [ 239.679134] rtl_usb: reg 0x30, usbctrl_vendorreq TimeOut!
>> status:0xffffffed value=0x80206f30
>> [ 239.700640] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
>> [ 239.700648] BUG: unable to handle kernel NULL pointer dereference at
>> (null)
>> [ 239.700682] IP: rtl_deinit_core+0x2e/0x90 [rtlwifi]
>> [ 239.700693] PGD 1c5d5d067
>> [ 239.700694] P4D 1c5d5d067
>> [ 239.700701] PUD 1c5d9b067
>> [ 239.700708] PMD 0
>>
>> [ 239.700727] Oops: 0000 [#1] SMP
>> [ 239.700735] Modules linked in: rtl8192cu(+) rtl_usb rtl8192c_common
>> rtlwifi mac80211 cfg80211 rfkill appletalk ipx p8023 p8022 psnap llc nct6775
>> hwmon_vid ipv6 hid_generic usbhid hid coretemp hwmon x86_pkg_temp_thermal
>> intel_powerclamp snd_hda_codec_hdmi snd_hda_codec_realtek
>> snd_hda_codec_generic kvm_intel i915 kvm drm_kms_helper evdev i2c_dev
>> irqbypass syscopyarea sysfillrect sysimgblt r8169 crc32_pclmul serio_raw
>> crc32c_intel mii snd_pcsp fb_sys_fops drm fan thermal button battery 8250
>> 8250_base serial_core mei_me snd_hda_intel mei intel_gtt snd_hda_codec video
>> agpgart ehci_pci ehci_hcd lpc_ich snd_hwdep snd_hda_core snd_pcm
>> i2c_algo_bit snd_timer i2c_i801 i2c_core snd soundcore fuse
>> [ 239.700875] CPU: 0 PID: 1174 Comm: udevd Not tainted 4.13.6.20171012 #1
>> [ 239.700889] Hardware name: To be filled by O.E.M. To be filled by
>> O.E.M./ONDA H61V Ver:4.01, BIOS 4.6.5 01/07/2013
>> [ 239.700909] task: ffff8801c5fbc980 task.stack: ffffc900009a0000
>> [ 239.700924] RIP: 0010:rtl_deinit_core+0x2e/0x90 [rtlwifi]
>> [ 239.700936] RSP: 0000:ffffc900009a3b40 EFLAGS: 00010207
>> [ 239.700947] RAX: 0000000000000282 RBX: ffff8801b9440780 RCX:
>> 00000000ffffffea
>> [ 239.700962] RDX: 0000000000000001 RSI: 0000000000000282 RDI:
>> 0000000000000000
>> [ 239.700977] RBP: ffff8801b944b070 R08: 0000000000000001 R09:
>> 00000000000002b0
>> [ 239.700991] R10: ffffea0008473480 R11: 0000000000000000 R12:
>> ffff8801b9441560
>> [ 239.701006] R13: ffff8801b944b880 R14: 0000000000000000 R15:
>> ffff8801b9441560
>> [ 239.701021] FS: 00007f3eb636e7c0(0000) GS:ffff88021f200000(0000)
>> knlGS:0000000000000000
>> [ 239.701037] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
>> [ 239.701050] CR2: 0000000000000000 CR3: 00000001c5d99000 CR4:
>> 00000000001406f0
>> [ 239.701064] Call Trace:
>> [ 239.701074] ? rtl_usb_probe+0x6b6/0xc50 [rtl_usb]
>> [ 239.701088] ? usb_probe_interface+0xe2/0x2a0
>> [ 239.701100] ? driver_probe_device+0x21d/0x2d0
>> [ 239.701111] ? __driver_attach+0x8a/0x90
>> [ 239.701121] ? driver_probe_device+0x2d0/0x2d0
>> [ 239.701133] ? bus_for_each_dev+0x5c/0x90
>> [ 239.701143] ? bus_add_driver+0x196/0x220
>> [ 239.701154] ? driver_register+0x57/0xc0
>> [ 239.701165] ? usb_register_driver+0x7c/0x140
>> [ 239.701175] ? 0xffffffffa064e000
>> [ 239.701185] ? do_one_initcall+0x4b/0x190
>> [ 239.701197] ? kmem_cache_alloc_trace+0xe4/0x1c0
>> [ 239.701208] ? do_init_module+0x22/0x1e1
>> [ 239.701219] ? do_init_module+0x5b/0x1e1
>> [ 239.701229] ? load_module+0x21ff/0x2760
>> [ 239.701239] ? SYSC_finit_module+0x90/0xb0
>> [ 239.701249] ? SYSC_finit_module+0x90/0xb0
>> [ 239.701261] ? entry_SYSCALL_64_fastpath+0x1a/0xa5
>> [ 239.701272] Code: 00 00 41 57 31 f6 41 56 41 55 41 54 55 53 48 89 fb e8
>> e7 fe ff ff 4c 8b 7b 48 49 8b bf 10 9b 00 00 49 8d af 10 9b 00 00 48 39 ef
>> <48> 8b 1f 74 44 49 bd 00 01 00 00 00 00 ad de 49 89 de 49 bc 00
>> [ 239.701327] RIP: rtl_deinit_core+0x2e/0x90 [rtlwifi] RSP:
>> ffffc900009a3b40
>> [ 239.702028] CR2: 0000000000000000
>> [ 239.705370] ---[ end trace 6ec9029c0d9c0e13 ]---
>> [ 239.706311] udevd[528]: worker [1174] failed while handling
>> '/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0'
>>
On 10/27/2017 07:57 AM, James Cameron wrote:
> On Fri, Oct 27, 2017 at 04:08:48AM +0300, nirinA raseliarison wrote:
>> hi all,
>> i applied the patch against 4.13.8. i still got some trouble, dmesg
>> is below.
>
> As this new event does not have "disabled by hub (EMI?)", it is a
> different problem to your 19th October post, so I don't think the
> patch is relevant.
>
>> after i plugged the device, it seems to be detected and all modules
>> loaded, but when i tried to connect to an access point, by using
>> wicd, it halted after a while. at this point, all usb ports are
>> broken, there was no more log in dmesg,
>
> If the other USB ports are not responding, then your problem is
> probably wider than the wireless device, and the wireless device
> is acting as the "canary in the mine"; failing first because it is
> the most active.
>
> Can you test to exclude possibility of damaged USB host controller or
> hub?
yes, dmesg below with an usb audio adapter and a usb mouse plugged at
boot time. then the rtl8192cu plugged, and i'm using it to retrieve
and send this mail.
my first guess was also about a damaged device or usb port
as those random crashes are recent.
note that the device i'm using here is not the same as the one
that triggered the previous errors.
>> lsusb still showed the device even after being unplugged. it got
>> even worse as reboot failed.
>
> Yes, once a USB host controller is failed, organised reboot can be
> difficult. lsusb not updated confirms host controller not responding.
>
>> i cannot really trace the error as right now all thing works fine.
>
> Your dmesg looks like you removed and reinserted the wireless device
> several times. Did you do that, or did the system do it without any
> physical action?
no, the device was always connected. i've only removed it long after
i noticed something went wrong and just before i tried reboot.
> A full dmesg from boot may be interesting, at least to better
> understand the USB host controller.
>
here it is.
thanks,
##
[ 0.000000] random: get_random_bytes called from
start_kernel+0x2a/0x413 with crng_init=0
[ 0.000000] Linux version 4.13.8.20171019 (root@supernova) (gcc
version 7.2.0 (GCC)) #1 SMP Thu Oct 19 03:53:05 EAT 2017
[ 0.000000] Command line: BOOT_IMAGE=nirinA ro root=802
vt.default_utf8=0 console=tty0 raid=noautodetect
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating
point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.000000] x86/fpu: Enabled xstate features 0x3, context size is 576
bytes, using 'standard' format.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x0000000020200000-0x0000000040003fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000040004000-0x0000000040004fff]
reserved
[ 0.000000] BIOS-e820: [mem 0x0000000040005000-0x00000000cdf30fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000cdf31000-0x00000000ce25afff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ce25b000-0x00000000ce25bfff]
ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000ce25c000-0x00000000ce373fff]
ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000ce374000-0x00000000ce6d8fff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ce6d9000-0x00000000ce6d9fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000ce6da000-0x00000000ce71cfff]
ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000ce71d000-0x00000000cee19fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000cee1a000-0x00000000ceff1fff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ceff2000-0x00000000ceffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000cf800000-0x00000000df9fffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000021f5fffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] random: fast init done
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: To be filled by O.E.M. To be filled by O.E.M./ONDA
H61V Ver:4.01, BIOS 4.6.5 01/07/2013
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x21f600 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-D3FFF write-protect
[ 0.000000] D4000-E7FFF uncachable
[ 0.000000] E8000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask E00000000 write-back
[ 0.000000] 1 base 200000000 mask FE0000000 write-back
[ 0.000000] 2 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 3 base 0D0000000 mask FF0000000 uncachable
[ 0.000000] 4 base 0CF800000 mask FFF800000 uncachable
[ 0.000000] 5 base 21F800000 mask FFF800000 uncachable
[ 0.000000] 6 base 21F600000 mask FFFE00000 uncachable
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WC UC-
WT
[ 0.000000] e820: update [mem 0xcf800000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xcf000 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000fd6f0-0x000fd6ff] mapped
at [ffff8800000fd6f0]
[ 0.000000] Base memory trampoline at [ffff880000097000] 97000 size 24576
[ 0.000000] BRK [0x02145000, 0x02145fff] PGTABLE
[ 0.000000] BRK [0x02146000, 0x02146fff] PGTABLE
[ 0.000000] BRK [0x02147000, 0x02147fff] PGTABLE
[ 0.000000] BRK [0x02148000, 0x02148fff] PGTABLE
[ 0.000000] BRK [0x02149000, 0x02149fff] PGTABLE
[ 0.000000] BRK [0x0214a000, 0x0214afff] PGTABLE
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F0490 000024 (v02 ALASKA)
[ 0.000000] ACPI: XSDT 0x00000000CE362070 000064 (v01 ALASKA A M I
01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 0x00000000CE36B698 0000F4 (v04 ALASKA A M I
01072009 AMI 00010013)
[ 0.000000] ACPI: DSDT 0x00000000CE362170 009526 (v02 ALASKA A M I
00000660 INTL 20051117)
[ 0.000000] ACPI: FACS 0x00000000CE372F80 000040
[ 0.000000] ACPI: APIC 0x00000000CE36B790 000062 (v03 ALASKA A M I
01072009 AMI 00010013)
[ 0.000000] ACPI: FPDT 0x00000000CE36B7F8 000044 (v01 ALASKA A M I
01072009 AMI 00010013)
[ 0.000000] ACPI: MCFG 0x00000000CE36B840 00003C (v01 ALASKA A M I
01072009 MSFT 00000097)
[ 0.000000] ACPI: HPET 0x00000000CE36B880 000038 (v01 ALASKA A M I
01072009 AMI. 00000005)
[ 0.000000] ACPI: SSDT 0x00000000CE36B8B8 00036D (v01 SataRe SataTabl
00001000 INTL 20091112)
[ 0.000000] ACPI: SSDT 0x00000000CE36BC28 000860 (v01 PmRef Cpu0Ist
00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 0x00000000CE36C488 000A92 (v01 PmRef CpuPm
00003000 INTL 20051117)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000021f5fffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009cfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x000000001fffffff]
[ 0.000000] node 0: [mem 0x0000000020200000-0x0000000040003fff]
[ 0.000000] node 0: [mem 0x0000000040005000-0x00000000cdf30fff]
[ 0.000000] node 0: [mem 0x00000000ce6d9000-0x00000000ce6d9fff]
[ 0.000000] node 0: [mem 0x00000000ce71d000-0x00000000cee19fff]
[ 0.000000] node 0: [mem 0x00000000ceff2000-0x00000000ceffffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000021f5fffff]
[ 0.000000] Initmem setup node 0 [mem
0x0000000000001000-0x000000021f5fffff]
[ 0.000000] On node 0 totalpages: 2021848
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3996 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 13137 pages used for memmap
[ 0.000000] DMA32 zone: 840764 pages, LIFO batch:31
[ 0.000000] Normal zone: 18392 pages used for memmap
[ 0.000000] Normal zone: 1177088 pages, LIFO batch:31
[ 0.000000] Reserving Intel graphics memory at
0x00000000cfa00000-0x00000000df9fffff
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI
0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009dfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x20000000-0x201fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x40004000-0x40004fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcdf31000-0xce25afff]
[ 0.000000] PM: Registered nosave memory: [mem 0xce25b000-0xce25bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xce25c000-0xce373fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xce374000-0xce6d8fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xce6da000-0xce71cfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcee1a000-0xceff1fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcf000000-0xcf7fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcf800000-0xdf9fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdfa00000-0xf7ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed03fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed1bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[ 0.000000] e820: [mem 0xdfa00000-0xf7ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff
max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2
nr_node_ids:1
[ 0.000000] percpu: Embedded 37 pages/cpu @ffff88021f200000 s111192
r8192 d32168 u1048576
[ 0.000000] pcpu-alloc: s111192 r8192 d32168 u1048576 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 1990234
[ 0.000000] Kernel command line: BOOT_IMAGE=nirinA ro root=802
vt.default_utf8=0 console=tty0 raid=noautodetect
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 1048576 (order: 11,
8388608 bytes)
[ 0.000000] Inode-cache hash table entries: 524288 (order: 10,
4194304 bytes)
[ 0.000000] Memory: 7863988K/8087392K available (9617K kernel code,
1116K rwdata, 3012K rodata, 1440K init, 660K bss, 223404K reserved, 0K
cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] ftrace: allocating 36813 entries in 144 pages
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 4352, nr_irqs: 440, preallocated irqs: 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 133484882848 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.001000] tsc: Detected 2594.066 MHz processor
[ 0.001000] Calibrating delay loop (skipped), value calculated using
timer frequency.. 5188.13 BogoMIPS (lpj=2594066)
[ 0.001000] pid_max: default: 32768 minimum: 301
[ 0.001000] ACPI: Core revision 20170531
[ 0.005766] ACPI: 4 ACPI AML tables successfully acquired and loaded
[ 0.005787] Security Framework initialized
[ 0.005817] Mount-cache hash table entries: 16384 (order: 5, 131072
bytes)
[ 0.005843] Mountpoint-cache hash table entries: 16384 (order: 5,
131072 bytes)
[ 0.005982] CPU: Physical Processor ID: 0
[ 0.005986] CPU: Processor Core ID: 0
[ 0.005991] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.006003] ENERGY_PERF_BIAS: View and update with
x86_energy_perf_policy(8)
[ 0.006009] mce: CPU supports 7 MCE banks
[ 0.006018] CPU0: Thermal monitoring enabled (TM1)
[ 0.006028] process: using mwait in idle threads
[ 0.006032] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 8
[ 0.006035] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
[ 0.006111] Freeing SMP alternatives memory: 36K
[ 0.007054] smpboot: Max logical packages: 1
[ 0.007467] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.017646] TSC deadline timer enabled
[ 0.017648] smpboot: CPU0: Intel(R) Celeron(R) CPU G1610 @ 2.60GHz
(family: 0x6, model: 0x3a, stepping: 0x9)
[ 0.017701] Performance Events: PEBS fmt1+, IvyBridge events, 16-deep
LBR, full-width counters, Intel PMU driver.
[ 0.017726] ... version: 3
[ 0.017728] ... bit width: 48
[ 0.017731] ... generic registers: 8
[ 0.017734] ... value mask: 0000ffffffffffff
[ 0.017737] ... max period: 00007fffffffffff
[ 0.017740] ... fixed-purpose events: 3
[ 0.017743] ... event mask: 00000007000000ff
[ 0.017772] Hierarchical SRCU implementation.
[ 0.017840] smp: Bringing up secondary CPUs ...
[ 0.017888] x86: Booting SMP configuration:
[ 0.017892] .... node #0, CPUs: #1
[ 0.078018] smp: Brought up 1 node, 2 CPUs
[ 0.078018] smpboot: Total of 2 processors activated (10379.97 BogoMIPS)
[ 0.079123] devtmpfs: initialized
[ 0.079123] x86/mm: Memory block size: 128MB
[ 0.079489] PM: Registering ACPI NVS region [mem
0xce25c000-0xce373fff] (1146880 bytes)
[ 0.079489] PM: Registering ACPI NVS region [mem
0xce6da000-0xce71cfff] (274432 bytes)
[ 0.079489] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.079489] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.079489] pinctrl core: initialized pinctrl subsystem
[ 0.079489] NET: Registered protocol family 16
[ 0.080026] cpuidle: using governor ladder
[ 0.080026] cpuidle: using governor menu
[ 0.080026] PCCT header not found.
[ 0.080048] ACPI: bus type PCI registered
[ 0.080052] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.080082] PCI: Using configuration type 1 for base access
[ 0.080122] core: PMU erratum BJ122, BV98, HSD29 workaround disabled,
HT off
[ 0.083368] ACPI: Added _OSI(Module Device)
[ 0.083368] ACPI: Added _OSI(Processor Device)
[ 0.083368] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.083368] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.083368] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.086305] ACPI: Dynamic OEM Table Load:
[ 0.086314] ACPI: SSDT 0xFFFF880216669000 00083B (v01 PmRef Cpu0Cst
00003001 INTL 20051117)
[ 0.086395] ACPI: Dynamic OEM Table Load:
[ 0.086395] ACPI: SSDT 0xFFFF88021642DC00 000303 (v01 PmRef ApIst
00003000 INTL 20051117)
[ 0.087030] ACPI: Dynamic OEM Table Load:
[ 0.087035] ACPI: SSDT 0xFFFF880216708200 000119 (v01 PmRef ApCst
00003000 INTL 20051117)
[ 0.087379] ACPI: Interpreter enabled
[ 0.087401] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.087404] ACPI: Using IOAPIC for interrupt routing
[ 0.087428] PCI: Using host bridge windows from ACPI; if necessary,
use "pci=nocrs" and report a bug
[ 0.092821] ACPI: Power Resource [FN00] (off)
[ 0.092884] ACPI: Power Resource [FN01] (off)
[ 0.092945] ACPI: Power Resource [FN02] (off)
[ 0.093005] ACPI: Power Resource [FN03] (off)
[ 0.093066] ACPI: Power Resource [FN04] (off)
[ 0.093467] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.093474] acpi PNP0A08:00: _OSC: OS supports [ASPM ClockPM Segments
MSI]
[ 0.093596] acpi PNP0A08:00: _OSC: not requesting OS control; OS
requires [ExtendedConfig ASPM ClockPM MSI]
[ 0.093955] PCI host bridge to bus 0000:00
[ 0.093960] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 0.093963] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.093967] pci_bus 0000:00: root bus resource [mem
0x000a0000-0x000bffff window]
[ 0.093972] pci_bus 0000:00: root bus resource [mem
0x000d4000-0x000d7fff window]
[ 0.093978] pci_bus 0000:00: root bus resource [mem
0x000d8000-0x000dbfff window]
[ 0.093983] pci_bus 0000:00: root bus resource [mem
0x000dc000-0x000dffff window]
[ 0.093988] pci_bus 0000:00: root bus resource [mem
0x000e0000-0x000e3fff window]
[ 0.093993] pci_bus 0000:00: root bus resource [mem
0x000e4000-0x000e7fff window]
[ 0.093998] pci_bus 0000:00: root bus resource [mem
0xdfa00000-0xfeafffff window]
[ 0.094002] pci_bus 0000:00: root bus resource [bus 00-3e]
[ 0.094012] pci 0000:00:00.0: [8086:0150] type 00 class 0x060000
[ 0.094090] pci 0000:00:02.0: [8086:0152] type 00 class 0x030000
[ 0.094100] pci 0000:00:02.0: reg 0x10: [mem 0xf7800000-0xf7bfffff 64bit]
[ 0.094105] pci 0000:00:02.0: reg 0x18: [mem 0xe0000000-0xefffffff
64bit pref]
[ 0.094109] pci 0000:00:02.0: reg 0x20: [io 0xf000-0xf03f]
[ 0.094202] pci 0000:00:16.0: [8086:1c3a] type 00 class 0x078000
[ 0.094227] pci 0000:00:16.0: reg 0x10: [mem 0xf7c0a000-0xf7c0a00f 64bit]
[ 0.094298] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.094370] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320
[ 0.094391] pci 0000:00:1a.0: reg 0x10: [mem 0xf7c08000-0xf7c083ff]
[ 0.094474] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.094540] pci 0000:00:1b.0: [8086:1c20] type 00 class 0x040300
[ 0.094558] pci 0000:00:1b.0: reg 0x10: [mem 0xf7c00000-0xf7c03fff 64bit]
[ 0.094623] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.094688] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400
[ 0.094764] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.094834] pci 0000:00:1c.2: [8086:1c14] type 01 class 0x060400
[ 0.094909] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.094983] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320
[ 0.095004] pci 0000:00:1d.0: reg 0x10: [mem 0xf7c07000-0xf7c073ff]
[ 0.095086] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.095153] pci 0000:00:1f.0: [8086:1c5c] type 00 class 0x060100
[ 0.095317] pci 0000:00:1f.2: [8086:1c02] type 00 class 0x010601
[ 0.095335] pci 0000:00:1f.2: reg 0x10: [io 0xf0b0-0xf0b7]
[ 0.095342] pci 0000:00:1f.2: reg 0x14: [io 0xf0a0-0xf0a3]
[ 0.095350] pci 0000:00:1f.2: reg 0x18: [io 0xf090-0xf097]
[ 0.095357] pci 0000:00:1f.2: reg 0x1c: [io 0xf080-0xf083]
[ 0.095364] pci 0000:00:1f.2: reg 0x20: [io 0xf060-0xf07f]
[ 0.095371] pci 0000:00:1f.2: reg 0x24: [mem 0xf7c06000-0xf7c067ff]
[ 0.095411] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.095471] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500
[ 0.095489] pci 0000:00:1f.3: reg 0x10: [mem 0xf7c05000-0xf7c050ff 64bit]
[ 0.095509] pci 0000:00:1f.3: reg 0x20: [io 0xf040-0xf05f]
[ 0.095626] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.095700] pci 0000:02:00.0: [10ec:8136] type 00 class 0x020000
[ 0.095725] pci 0000:02:00.0: reg 0x10: [io 0xe000-0xe0ff]
[ 0.095758] pci 0000:02:00.0: reg 0x18: [mem 0xf0004000-0xf0004fff
64bit pref]
[ 0.095778] pci 0000:02:00.0: reg 0x20: [mem 0xf0000000-0xf0003fff
64bit pref]
[ 0.095870] pci 0000:02:00.0: supports D1 D2
[ 0.095871] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.098023] pci 0000:00:1c.2: PCI bridge to [bus 02]
[ 0.098032] pci 0000:00:1c.2: bridge window [io 0xe000-0xefff]
[ 0.098042] pci 0000:00:1c.2: bridge window [mem
0xf0000000-0xf00fffff 64bit pref]
[ 0.098071] pci_bus 0000:00: on NUMA node 0
[ 0.098356] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12
14 15)
[ 0.098402] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14
15) *0, disabled.
[ 0.098448] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 10 11 12
14 15)
[ 0.098490] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12
14 15)
[ 0.098533] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14
15) *0, disabled.
[ 0.098578] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14
15) *0, disabled.
[ 0.098623] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 10 11 12
14 15)
[ 0.098666] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12
14 15)
[ 0.098825] ACPI: Enabled 4 GPEs in block 00 to 3F
[ 0.098882] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[ 0.098882] pci 0000:00:02.0: vgaarb: VGA device added:
decodes=io+mem,owns=io+mem,locks=none
[ 0.098882] pci 0000:00:02.0: vgaarb: bridge control possible
[ 0.098882] vgaarb: loaded
[ 0.098882] SCSI subsystem initialized
[ 0.099002] libata version 3.00 loaded.
[ 0.099005] ACPI: bus type USB registered
[ 0.099023] usbcore: registered new interface driver usbfs
[ 0.099033] usbcore: registered new interface driver hub
[ 0.099043] usbcore: registered new device driver usb
[ 0.099057] EDAC MC: Ver: 3.0.0
[ 0.099114] PCI: Using ACPI for IRQ routing
[ 0.099114] PCI: pci_cache_line_size set to 64 bytes
[ 0.099114] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[ 0.099114] e820: reserve RAM buffer [mem 0x40004000-0x43ffffff]
[ 0.099114] e820: reserve RAM buffer [mem 0xcdf31000-0xcfffffff]
[ 0.099114] e820: reserve RAM buffer [mem 0xce6da000-0xcfffffff]
[ 0.099114] e820: reserve RAM buffer [mem 0xcee1a000-0xcfffffff]
[ 0.099114] e820: reserve RAM buffer [mem 0xcf000000-0xcfffffff]
[ 0.099114] e820: reserve RAM buffer [mem 0x21f600000-0x21fffffff]
[ 0.099133] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.099133] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.101009] clocksource: Switched to clocksource hpet
[ 0.106961] VFS: Disk quotas dquot_6.6.0
[ 0.106981] VFS: Dquot-cache hash table entries: 512 (order 0, 4096
bytes)
[ 0.107043] pnp: PnP ACPI init
[ 0.107133] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[ 0.107139] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.107197] system 00:01: [io 0x0680-0x069f] has been reserved
[ 0.107201] system 00:01: [io 0x0200-0x020f] has been reserved
[ 0.107205] system 00:01: [io 0xffff] has been reserved
[ 0.107209] system 00:01: [io 0xffff] has been reserved
[ 0.107212] system 00:01: [io 0x0400-0x0453] has been reserved
[ 0.107216] system 00:01: [io 0x0458-0x047f] has been reserved
[ 0.107219] system 00:01: [io 0x0500-0x057f] has been reserved
[ 0.107223] system 00:01: [io 0x164e-0x164f] has been reserved
[ 0.107227] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.107245] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.107278] system 00:03: [io 0x0454-0x0457] has been reserved
[ 0.107282] system 00:03: Plug and Play ACPI device, IDs INT3f0d
PNP0c02 (active)
[ 0.107342] system 00:04: [io 0x0a30-0x0a3f] has been reserved
[ 0.107346] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.107376] pnp 00:05: Plug and Play ACPI device, IDs PNP0303 PNP030b
(active)
[ 0.107487] pnp 00:06: [dma 0 disabled]
[ 0.107520] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.107553] system 00:07: [io 0x04d0-0x04d1] has been reserved
[ 0.107558] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.107712] system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.107716] system 00:08: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.107720] system 00:08: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.107724] system 00:08: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.107727] system 00:08: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.107731] system 00:08: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.107735] system 00:08: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.107739] system 00:08: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.107742] system 00:08: [mem 0xff000000-0xffffffff] has been reserved
[ 0.107746] system 00:08: [mem 0xfee00000-0xfeefffff] could not be
reserved
[ 0.107750] system 00:08: [mem 0xdfa00000-0xdfa00fff] has been reserved
[ 0.107754] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.107866] system 00:09: [mem 0x20000000-0x201fffff] has been reserved
[ 0.107870] system 00:09: [mem 0x40004000-0x40004fff] has been reserved
[ 0.107874] system 00:09: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.107891] pnp: PnP ACPI: found 10 devices
[ 0.113798] clocksource: acpi_pm: mask: 0xffffff max_cycles:
0xffffff, max_idle_ns: 2085701024 ns
[ 0.113825] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.113839] pci 0000:00:1c.2: PCI bridge to [bus 02]
[ 0.113845] pci 0000:00:1c.2: bridge window [io 0xe000-0xefff]
[ 0.113854] pci 0000:00:1c.2: bridge window [mem
0xf0000000-0xf00fffff 64bit pref]
[ 0.113865] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.113866] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.113867] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff
window]
[ 0.113868] pci_bus 0000:00: resource 7 [mem 0x000d4000-0x000d7fff
window]
[ 0.113869] pci_bus 0000:00: resource 8 [mem 0x000d8000-0x000dbfff
window]
[ 0.113870] pci_bus 0000:00: resource 9 [mem 0x000dc000-0x000dffff
window]
[ 0.113871] pci_bus 0000:00: resource 10 [mem 0x000e0000-0x000e3fff
window]
[ 0.113872] pci_bus 0000:00: resource 11 [mem 0x000e4000-0x000e7fff
window]
[ 0.113873] pci_bus 0000:00: resource 12 [mem 0xdfa00000-0xfeafffff
window]
[ 0.113874] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
[ 0.113875] pci_bus 0000:02: resource 2 [mem 0xf0000000-0xf00fffff
64bit pref]
[ 0.113947] NET: Registered protocol family 2
[ 0.114057] TCP established hash table entries: 65536 (order: 7,
524288 bytes)
[ 0.114158] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.114341] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.114371] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.114399] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.114458] NET: Registered protocol family 1
[ 0.114555] RPC: Registered named UNIX socket transport module.
[ 0.114559] RPC: Registered udp transport module.
[ 0.114562] RPC: Registered tcp transport module.
[ 0.114564] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.114579] pmd_set_huge: Cannot satisfy [mem 0xf7800000-0xf7a00000]
with a huge-page mapping due to MTRR override.
[ 0.114592] pci 0000:00:02.0: BIOS left Intel GPU interrupts enabled;
disabling
[ 0.114611] pci 0000:00:02.0: Video device with shadowed ROM at [mem
0x000c0000-0x000dffff]
[ 0.147118] PCI: CLS 64 bytes, default 64
[ 0.147154] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.147158] software IO TLB [mem 0xc9f31000-0xcdf31000] (64MB) mapped
at [ffff8800c9f31000-ffff8800cdf30fff]
[ 0.147223] RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters,
163840 ms ovfl timer
[ 0.147228] RAPL PMU: hw unit of domain pp0-core 2^-16 Joules
[ 0.147231] RAPL PMU: hw unit of domain package 2^-16 Joules
[ 0.147234] RAPL PMU: hw unit of domain pp1-gpu 2^-16 Joules
[ 0.147496] audit: initializing netlink subsys (disabled)
[ 0.147530] audit: type=2000 audit(1509135453.147:1):
state=initialized audit_enabled=0 res=1
[ 0.147671] workingset: timestamp_bits=46 max_order=21 bucket_order=0
[ 0.148709] NFS: Registering the id_resolver key type
[ 0.148718] Key type id_resolver registered
[ 0.148721] Key type id_legacy registered
[ 0.148725] Installing knfsd (copyright (C) 1996 [email protected]).
[ 0.148801] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.148830] romfs: ROMFS MTD (C) 2007 Red Hat, Inc.
[ 0.150274] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 252)
[ 0.150303] io scheduler noop registered
[ 0.150306] io scheduler deadline registered
[ 0.150327] io scheduler cfq registered (default)
[ 0.150330] io scheduler mq-deadline registered
[ 0.150333] io scheduler kyber registered
[ 0.150618] vesafb: mode is 1024x768x16, linelength=2048, pages=169
[ 0.150622] vesafb: scrolling: redraw
[ 0.150625] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 0.150638] vesafb: framebuffer at 0xe0000000, mapped to
0xffffc90000c00000, using 3072k, total 262080k
[ 0.175394] Console: switching to colour frame buffer device 128x48
[ 0.198189] fb0: VESA VGA frame buffer device
[ 0.198401] intel_idle: MWAIT substates: 0x1120
[ 0.198402] intel_idle: v0.4.1 model 0x3A
[ 0.198455] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.198512] GHES: HEST is not enabled!
[ 0.201091] brd: module loaded
[ 0.201390] fnic: Cisco FCoE HBA Driver, ver 1.6.0.34
[ 0.201638] fnic: Successfully Initialized Trace Buffer
[ 0.201906] fnic: Successfully Initialized FC_CTLR Trace Buffer
[ 0.202354] Adaptec aacraid driver 1.2.1[50834]-custom
[ 0.202601] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
[ 0.203042] scsi: <fdomain> Detection failed (no card)
[ 0.203293] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA
Driver: 10.00.00.00-k.
[ 0.203682] Emulex LightPulse Fibre Channel SCSI driver 11.4.0.1
[ 0.203960] Copyright (C) 2017 Broadcom. All Rights Reserved. The
term "Broadcom" refers to Broadcom Limited and/or its subsidiaries.
[ 0.204583] QLogic BR-series BFA FC/FCOE SCSI driver - version: 3.2.25.1
[ 0.204927] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03
EST 2006)
[ 0.205288] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST
2006)
[ 0.205618] megasas: 07.701.17.00-rc1
[ 0.205797] mpt3sas version 15.100.00.00 loaded
[ 0.215058] GDT-HA: Storage RAID Controller Driver. Version: 3.05
[ 0.224498] 3ware Storage Controller device driver for Linux
v1.26.02.003.
[ 0.233996] 3ware 9000 Storage Controller device driver for Linux
v2.26.02.014.
[ 0.243526] LSI 3ware SAS/SATA-RAID Controller device driver for
Linux v3.26.02.000.
[ 0.253071] ipr: IBM Power RAID SCSI Device Driver version: 2.6.4
(March 14, 2017)
[ 0.262627] RocketRAID 3xxx/4xxx Controller driver v1.10.0
[ 0.272099] stex: Promise SuperTrak EX Driver version: 6.02.0000.01
[ 0.281704] st: Version 20160209, fixed bufsize 32768, s/g segs 256
[ 0.291470] ahci 0000:00:1f.2: version 3.0
[ 0.291637] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 3 Gbps
0x3 impl SATA mode
[ 0.301535] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum
part ems apst
[ 0.314344] scsi host0: ahci
[ 0.324214] scsi host1: ahci
[ 0.333812] scsi host2: ahci
[ 0.343146] scsi host3: ahci
[ 0.352316] ata1: SATA max UDMA/133 abar m2048@0xf7c06000 port
0xf7c06100 irq 24
[ 0.361837] ata2: SATA max UDMA/133 abar m2048@0xf7c06000 port
0xf7c06180 irq 24
[ 0.371288] ata3: DUMMY
[ 0.380649] ata4: DUMMY
[ 0.390440] scsi host4: pata_legacy
[ 0.399689] ata5: PATA max PIO4 cmd 0x1f0 ctl 0x3f6 irq 14
[ 0.708585] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 0.718014] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 0.727274] ACPI Error: [DSSP] Namespace lookup failure, AE_NOT_FOUND
(20170531/psargs-364)
[ 0.736604] ACPI Error: Method parse/execution failed
\_SB.PCI0.SAT0.SPT0._GTF, AE_NOT_FOUND (20170531/psparse-550)
[ 0.746153] ACPI Error: [DSSP] Namespace lookup failure, AE_NOT_FOUND
(20170531/psargs-364)
[ 0.755718] ACPI Error: Method parse/execution failed
\_SB.PCI0.SAT0.SPT1._GTF, AE_NOT_FOUND (20170531/psparse-550)
[ 0.765606] ata2.00: ATAPI: TSSTcorp CDDVDW SH-224BB, SB00, max UDMA/100
[ 0.775609] ata1.00: ATA-8: ST500DM002-1BD142, KC45, max UDMA/133
[ 0.785624] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 0.797067] ACPI Error: [DSSP] Namespace lookup failure, AE_NOT_FOUND
(20170531/psargs-364)
[ 0.807493] ACPI Error: Method parse/execution failed
\_SB.PCI0.SAT0.SPT0._GTF, AE_NOT_FOUND (20170531/psparse-550)
[ 0.818177] ACPI Error: [DSSP] Namespace lookup failure, AE_NOT_FOUND
(20170531/psargs-364)
[ 0.828867] ACPI Error: Method parse/execution failed
\_SB.PCI0.SAT0.SPT1._GTF, AE_NOT_FOUND (20170531/psparse-550)
[ 0.839762] ata2.00: configured for UDMA/100
[ 0.850477] ata1.00: configured for UDMA/133
[ 1.183036] tsc: Refined TSC clocksource calibration: 2594.107 MHz
[ 1.193411] clocksource: tsc: mask: 0xffffffffffffffff max_cycles:
0x25647d583cf, max_idle_ns: 440795304232 ns
[ 2.207229] clocksource: Switched to clocksource tsc
[ 3.231153] floppy0: no floppy controllers found
[ 3.241619] scsi 0:0:0:0: Direct-Access ATA ST500DM002-1BD14
KC45 PQ: 0 ANSI: 5
[ 3.252177] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500
GB/466 GiB)
[ 3.262613] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 3.273018] sd 0:0:0:0: [sda] Write Protect is off
[ 3.273021] scsi 1:0:0:0: CD-ROM TSSTcorp CDDVDW SH-224BB
SB00 PQ: 0 ANSI: 5
[ 3.293731] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.293742] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 3.319639] sr 1:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer dvd-ram
cd/rw xa/form2 cdda tray
[ 3.330204] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 3.340791] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 3.343079] sda: sda1 sda2 sda3 sda5 sda6
[ 3.353800] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.364320] scsi host4: pata_legacy
[ 3.374453] ata6: PATA max PIO4 cmd 0x170 ctl 0x376 irq 15
[ 3.543439] Fusion MPT base driver 3.04.20
[ 3.553407] Copyright (c) 1999-2008 LSI Corporation
[ 3.563330] Fusion MPT SPI Host driver 3.04.20
[ 3.573403] Fusion MPT FC Host driver 3.04.20
[ 3.583554] Fusion MPT SAS Host driver 3.04.20
[ 3.593795] Fusion MPT misc device (ioctl) driver 3.04.20
[ 3.604011] mptctl: Registered with Fusion MPT base driver
[ 3.614354] mptctl: /dev/mptctl @ (major,minor=10,220)
[ 3.624610] Fusion MPT LAN driver 3.04.20
[ 3.635049] usbcore: registered new interface driver usbserial
[ 3.645608] usbcore: registered new interface driver usbserial_generic
[ 3.656060] usbserial: USB Serial support registered for generic
[ 3.666540] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 3.677252] i8042: PNP: PS/2 appears to have AUX port disabled, if
this is incorrect please boot with i8042.nopnp
[ 3.688678] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.699471] mousedev: PS/2 mouse device common for all mice
[ 3.710012] rtc_cmos 00:02: RTC can wake from S4
[ 3.720448] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 3.730561] rtc_cmos 00:02: alarms up to one month, y3k, 242 bytes
nvram, hpet irqs
[ 3.740760] intel_pstate: Intel P-state driver initializing
[ 3.751077] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.766645] Initializing XFRM netlink socket
[ 3.776445] NET: Registered protocol family 17
[ 3.786018] Key type dns_resolver registered
[ 3.795546] microcode: sig=0x306a9, pf=0x2, revision=0x10
[ 3.804839] microcode: Microcode Update Driver: v2.2.
[ 3.804849] sched_clock: Marking stable (3804833789, 0)->(3805320172,
-486383)
[ 3.823571] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input0
[ 3.823649] registered taskstats version 1
[ 3.865260] EXT4-fs (sda2): couldn't mount as ext3 due to feature
incompatibilities
[ 3.917720] EXT4-fs (sda2): mounted filesystem with ordered data
mode. Opts: (null)
[ 3.932431] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[ 3.954965] devtmpfs: mounted
[ 3.965977] Freeing unused kernel memory: 1440K
[ 3.977257] Write protecting the kernel read-only data: 14336k
[ 3.986825] Freeing unused kernel memory: 616K
[ 3.998082] Freeing unused kernel memory: 1084K
[ 4.006960] rodata_test: all tests were successful
[ 4.673130] random: crng init done
[ 5.435976] udevd[153]: bind failed: Read-only file system
[ 5.449739] udevd[153]: error binding udev control socket
[ 5.593569] Adding 16787920k swap on /dev/sda3. Priority:-1
extents:1 across:16787920k
[ 5.936881] fuse init (API version 7.26)
[ 7.231377] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 7.270874] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 10.841139] EXT4-fs (sda5): mounted filesystem with ordered data
mode. Opts: (null)
[ 10.987833] EXT4-fs (sda6): mounted filesystem with ordered data
mode. Opts: (null)
[ 11.116467] EXT4-fs (sda1): mounted filesystem with ordered data
mode. Opts: (null)
[ 16.455793] udevd[528]: starting eudev-3.2.4
[ 17.002954] input: Power Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 17.002973] ACPI: Power Button [PWRB]
[ 17.003147] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 17.003158] ACPI: Power Button [PWRF]
[ 17.233207] ACPI Warning: SystemIO range
0x0000000000000428-0x000000000000042F conflicts with OpRegion
0x0000000000000400-0x000000000000047F (\PMIO) (20170531/utaddress-247)
[ 17.233212] ACPI: If an ACPI driver is available for this device, you
should use it instead of the native driver
[ 17.233214] ACPI Warning: SystemIO range
0x0000000000000540-0x000000000000054F conflicts with OpRegion
0x0000000000000500-0x0000000000000563 (\GPIO) (20170531/utaddress-247)
[ 17.233217] ACPI: If an ACPI driver is available for this device, you
should use it instead of the native driver
[ 17.233217] ACPI Warning: SystemIO range
0x0000000000000530-0x000000000000053F conflicts with OpRegion
0x0000000000000500-0x0000000000000563 (\GPIO) (20170531/utaddress-247)
[ 17.233220] ACPI: If an ACPI driver is available for this device, you
should use it instead of the native driver
[ 17.233220] ACPI Warning: SystemIO range
0x0000000000000500-0x000000000000052F conflicts with OpRegion
0x0000000000000500-0x0000000000000563 (\GPIO) (20170531/utaddress-247)
[ 17.233222] ACPI: If an ACPI driver is available for this device, you
should use it instead of the native driver
[ 17.233223] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 17.282124] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 17.288596] ehci-pci: EHCI PCI platform driver
[ 17.288760] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 17.288813] ehci-pci 0000:00:1a.0: new USB bus registered, assigned
bus number 1
[ 17.288827] ehci-pci 0000:00:1a.0: debug port 2
[ 17.292722] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[ 17.292738] ehci-pci 0000:00:1a.0: irq 16, io mem 0xf7c08000
[ 17.293717] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 17.314322] 00:06: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200)
is a 16550A
[ 17.314343] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 17.314391] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 17.314392] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 17.314393] usb usb1: Product: EHCI Host Controller
[ 17.314394] usb usb1: Manufacturer: Linux 4.13.8.20171019 ehci_hcd
[ 17.314395] usb usb1: SerialNumber: 0000:00:1a.0
[ 17.314493] hub 1-0:1.0: USB hub found
[ 17.314498] hub 1-0:1.0: 2 ports detected
[ 17.314705] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 17.314742] ehci-pci 0000:00:1d.0: new USB bus registered, assigned
bus number 2
[ 17.314753] ehci-pci 0000:00:1d.0: debug port 2
[ 17.318659] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 17.318671] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7c07000
[ 17.325011] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 17.325038] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 17.325039] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 17.325041] usb usb2: Product: EHCI Host Controller
[ 17.325042] usb usb2: Manufacturer: Linux 4.13.8.20171019 ehci_hcd
[ 17.325042] usb usb2: SerialNumber: 0000:00:1d.0
[ 17.325136] hub 2-0:1.0: USB hub found
[ 17.325140] hub 2-0:1.0: 2 ports detected
[ 17.340999] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
[ 17.355509] Linux agpgart interface v0.103
[ 17.423770] thermal LNXTHERM:00: registered as thermal_zone0
[ 17.423772] ACPI: Thermal Zone [TZ00] (28 C)
[ 17.424000] thermal LNXTHERM:01: registered as thermal_zone1
[ 17.424014] ACPI: Thermal Zone [TZ01] (30 C)
[ 17.580716] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 17.623013] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 17.640030] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 17.741402] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[ 17.741404] usb 1-1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 17.741545] hub 1-1:1.0: USB hub found
[ 17.741646] hub 1-1:1.0: 4 ports detected
[ 17.760429] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[ 17.760432] usb 2-1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 17.760682] hub 2-1:1.0: USB hub found
[ 17.760773] hub 2-1:1.0: 6 ports detected
[ 17.805182] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 17.805541] r8169 0000:02:00.0 eth0: RTL8105e at 0xffffc90000031000,
00:e0:66:84:16:a7, XID 00a00000 IRQ 26
[ 18.015031] usb 1-1.2: new full-speed USB device number 3 using ehci-pci
[ 18.031011] usb 2-1.3: new low-speed USB device number 3 using ehci-pci
[ 18.116428] usb 2-1.3: New USB device found, idVendor=1c4f,
idProduct=0034
[ 18.116431] usb 2-1.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 18.116432] usb 2-1.3: Product: Usb Mouse
[ 18.116434] usb 2-1.3: Manufacturer: SIGMACHIP
[ 18.141508] i2c /dev entries driver
[ 18.594623] [drm] Memory usable by graphics device = 2048M
[ 18.594626] checking generic (e0000000 fff0000) vs hw (e0000000 10000000)
[ 18.594627] fb: switching to inteldrmfb from VESA VGA
[ 18.594651] Console: switching to colour dummy device 80x25
[ 18.594736] [drm] Replacing VGA console driver
[ 18.601079] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 18.601080] [drm] Driver supports precise vblank timestamp query.
[ 18.604169] i915 0000:00:02.0: vgaarb: changed VGA decodes:
olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 18.608058] [drm] Initialized i915 1.6.0 20170619 for 0000:00:02.0 on
minor 0
[ 18.608403] ACPI: Video Device [GFX0] (multi-head: yes rom: no
post: no)
[ 18.608591] acpi device:49: registered as cooling_device7
[ 18.608642] input: Video Bus as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input4
[ 18.625111] snd_hda_intel 0000:00:1b.0: bound 0000:00:02.0 (ops
i915_audio_component_bind_ops [i915])
[ 18.655772] usb 1-1.2: New USB device found, idVendor=1b3f,
idProduct=2007
[ 18.655775] usb 1-1.2: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 18.655776] usb 1-1.2: Product: USB Audio Device
[ 18.655778] usb 1-1.2: Manufacturer: GeneralPlus
[ 18.671440] fbcon: inteldrmfb (fb0) is primary device
[ 18.733098] Console: switching to colour frame buffer device 170x48
[ 18.751719] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 19.250076] snd_hda_codec_realtek hdaudioC1D2: autoconfig for ALC662
rev3: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[ 19.250078] snd_hda_codec_realtek hdaudioC1D2: speaker_outs=0
(0x0/0x0/0x0/0x0/0x0)
[ 19.250080] snd_hda_codec_realtek hdaudioC1D2: hp_outs=1
(0x1b/0x0/0x0/0x0/0x0)
[ 19.250081] snd_hda_codec_realtek hdaudioC1D2: mono: mono_out=0x0
[ 19.250082] snd_hda_codec_realtek hdaudioC1D2: dig-out=0x1e/0x0
[ 19.250083] snd_hda_codec_realtek hdaudioC1D2: inputs:
[ 19.250085] snd_hda_codec_realtek hdaudioC1D2: Front Mic=0x19
[ 19.250086] snd_hda_codec_realtek hdaudioC1D2: Rear Mic=0x18
[ 19.250087] snd_hda_codec_realtek hdaudioC1D2: Line=0x1a
[ 19.617638] input: HDA Intel PCH Front Mic as
/devices/pci0000:00/0000:00:1b.0/sound/card1/input5
[ 19.617690] input: HDA Intel PCH Rear Mic as
/devices/pci0000:00/0000:00:1b.0/sound/card1/input6
[ 19.617720] input: HDA Intel PCH Line as
/devices/pci0000:00/0000:00:1b.0/sound/card1/input7
[ 19.617752] input: HDA Intel PCH Line Out as
/devices/pci0000:00/0000:00:1b.0/sound/card1/input8
[ 19.617782] input: HDA Intel PCH Front Headphone as
/devices/pci0000:00/0000:00:1b.0/sound/card1/input9
[ 19.617813] input: HDA Intel PCH HDMI/DP,pcm=3 as
/devices/pci0000:00/0000:00:1b.0/sound/card1/input10
[ 19.617843] input: HDA Intel PCH HDMI/DP,pcm=7 as
/devices/pci0000:00/0000:00:1b.0/sound/card1/input11
[ 19.617873] input: HDA Intel PCH HDMI/DP,pcm=8 as
/devices/pci0000:00/0000:00:1b.0/sound/card1/input12
[ 20.392010] usb 2-1.3: USB disconnect, device number 3
[ 20.657288] hidraw: raw HID events driver (C) Jiri Kosina
[ 20.703225] usbcore: registered new interface driver usbhid
[ 20.703226] usbhid: USB HID core driver
[ 20.734521] usb 1-1.2: 1:1: cannot get freq at ep 0x5
[ 20.735257] usb 1-1.2: 2:1: cannot get freq at ep 0x86
[ 20.751131] usbcore: registered new interface driver snd-usb-audio
[ 20.907898] input: GeneralPlus USB Audio Device as
/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.3/0003:1B3F:2007.0001/input/input13
[ 20.959334] hid-generic 0003:1B3F:2007.0001: input,hidraw0: USB HID
v2.01 Device [GeneralPlus USB Audio Device] on usb-0000:00:1a.0-1.2/input3
[ 21.815028] usb 2-1.3: new low-speed USB device number 4 using ehci-pci
[ 21.898249] usb 2-1.3: New USB device found, idVendor=1c4f,
idProduct=0034
[ 21.898252] usb 2-1.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 21.898254] usb 2-1.3: Product: Usb Mouse
[ 21.898255] usb 2-1.3: Manufacturer: SIGMACHIP
[ 21.900987] input: SIGMACHIP Usb Mouse as
/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/0003:1C4F:0034.0002/input/input14
[ 21.901152] hid-generic 0003:1C4F:0034.0002: input,hidraw1: USB HID
v1.10 Mouse [SIGMACHIP Usb Mouse] on usb-0000:00:1d.0-1.3/input0
[ 23.193054] r8169 0000:02:00.0 eth0: link down
[ 23.193070] r8169 0000:02:00.0 eth0: link down
[ 23.589795] NET: Registered protocol family 10
[ 23.590227] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 23.590274] Segment Routing with IPv6
[ 24.516778] NFSD: the nfsdcld client tracking upcall will be removed
in 3.10. Please transition to using nfsdcltrack.
[ 24.516780] NFSD: starting 90-second grace period (net ffffffff81ee6400)
[ 24.773386] r8169 0000:02:00.0 eth0: link up
[ 24.773400] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 35.748078] nct6775: Found NCT6779D or compatible chip at 0x2e:0xa30
[ 36.252940] NET: Registered protocol family 4
[ 36.266545] NET: Registered protocol family 5
[ 145.887086] NFSD: Unable to end grace period: -110
[ 309.194881] usb 1-1.2: 1:1: cannot get freq at ep 0x5
[ 813.692026] usb 2-1.4: new high-speed USB device number 5 using ehci-pci
[ 813.771752] usb 2-1.4: New USB device found, idVendor=0bda,
idProduct=8178
[ 813.771754] usb 2-1.4: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 813.771756] usb 2-1.4: Product: 802.11n WLAN Adapter
[ 813.771757] usb 2-1.4: Manufacturer: Realtek
[ 813.771757] usb 2-1.4: SerialNumber: 00e04c000001
[ 813.954745] rtl8192cu: Chip version 0x11
[ 814.031127] rtl8192cu: Board Type 0
[ 814.031368] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[ 814.031398] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
[ 814.031534] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 814.031712] usbcore: registered new interface driver rtl8192cu
[ 814.034508] usbcore: registered new interface driver rtl8xxxu
[ 814.114407] rtl8192cu 2-1.4:1.0 wlan125: renamed from wlan0
[ 814.119131] rtl8192cu 2-1.4:1.0 wlan1: renamed from wlan125
[ 872.272098] rtl8192cu: MAC auto ON okay!
[ 872.304968] rtl8192cu: Tx queue select: 0x05
[ 872.906879] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 881.042276] rtl8192cu: MAC auto ON okay!
[ 881.075282] rtl8192cu: Tx queue select: 0x05
[ 881.677711] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 881.840898] rtl8192cu: MAC auto ON okay!
[ 881.874650] rtl8192cu: Tx queue select: 0x05
[ 882.478431] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 885.721281] wlan1: authenticate with 16:6b:72:6d:9d:fc
[ 885.747759] wlan1: send auth to 16:6b:72:6d:9d:fc (try 1/3)
[ 885.751276] wlan1: authenticated
[ 885.752070] wlan1: associate with 16:6b:72:6d:9d:fc (try 1/3)
[ 885.768967] wlan1: RX AssocResp from 16:6b:72:6d:9d:fc (capab=0x431
status=0 aid=1)
[ 885.872798] wlan1: associated
[ 885.873506] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
##
--
nirinA
On 10/31/2017 06:11 AM, Barry Day wrote:
> On Sun, Oct 29, 2017 at 01:08:24AM +0300, nirinA raseliarison wrote:
>> [ 145.966016] usb 2-1.4: new high-speed USB device number 4 using ehci-pci
>> [ 146.045808] usb 2-1.4: New USB device found, idVendor=0bda,
>> idProduct=8178
>> [ 146.045811] usb 2-1.4: New USB device strings: Mfr=1, Product=2,
>> SerialNumber=3
>> [ 146.045812] usb 2-1.4: Product: 802.11n WLAN Adapter
>> [ 146.045813] usb 2-1.4: Manufacturer: Realtek
>> [ 146.045814] usb 2-1.4: SerialNumber: 00e04c000001
>> [ 146.202043] rtl8192cu: Chip version 0x11
>> [ 146.278549] rtl8192cu: Board Type 0
>> [ 146.278790] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
>> [ 146.278823] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
>> [ 146.278938] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
>> [ 146.279113] usbcore: registered new interface driver rtl8192cu
>> [ 146.281706] usbcore: registered new interface driver rtl8xxxu
>> --
>> nirinA
>
> It appears that both rtl8192cu and rtl8xxxu are being loaded for the
> one device.
>
> Try blacklisting one of them.
both seem to work fine; i'll use rtl8192cu and blacklist rtl8xxxu.
thanks,
> Barry
>
--
nirinA