From: Venkateswara Naralasetty <[email protected]>
User can extend test mode command support to set vdev and pdev params
for debug purpose at run time by sending vdev/pdev param set command
through the testmode command interface.
Fill the proper pdev/vdev id in driver since, pdev/vdev id details may
not be available at user space. It will make sure that the proper
vdev/pdev ids are sent to firmware.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Depends-On:
[v3,3/4] wifi: ath11k: factory test mode support
Signed-off-by: Venkateswara Naralasetty <[email protected]>
Signed-off-by: Raj Kumar Bhagat <[email protected]>
---
drivers/net/wireless/ath/ath11k/testmode.c | 37 ++++++++++++++++++++--
1 file changed, 34 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/ath/ath11k/testmode.c b/drivers/net/wireless/ath/ath11k/testmode.c
index bebd9c1776ba..e1edbc532eb6 100644
--- a/drivers/net/wireless/ath/ath11k/testmode.c
+++ b/drivers/net/wireless/ath/ath11k/testmode.c
@@ -250,13 +250,16 @@ static int ath11k_tm_cmd_testmode_start(struct ath11k *ar, struct nlattr *tb[])
return ret;
}
-static int ath11k_tm_cmd_wmi(struct ath11k *ar, struct nlattr *tb[])
+static int ath11k_tm_cmd_wmi(struct ath11k *ar, struct nlattr *tb[],
+ struct ieee80211_vif *vif)
{
struct ath11k_pdev_wmi *wmi = ar->wmi;
struct sk_buff *skb;
+ struct ath11k_vif *arvif;
u32 cmd_id, buf_len;
- int ret;
+ int ret, tag;
void *buf;
+ u32 *ptr;
mutex_lock(&ar->conf_mutex);
@@ -280,6 +283,34 @@ static int ath11k_tm_cmd_wmi(struct ath11k *ar, struct nlattr *tb[])
cmd_id = nla_get_u32(tb[ATH11K_TM_ATTR_WMI_CMDID]);
+ /* Make sure that the buffer length is long enough to
+ * hold TLV and pdev/vdev id.
+ */
+ if (buf_len < sizeof(struct wmi_tlv) + sizeof(u32)) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ ptr = buf;
+ tag = FIELD_GET(WMI_TLV_TAG, *ptr);
+
+ /* pdev/vdev id start after TLV header */
+ ptr++;
+
+ if (tag == WMI_TAG_PDEV_SET_PARAM_CMD)
+ *ptr = ar->pdev->pdev_id;
+
+ if (ar->ab->fw_mode != ATH11K_FIRMWARE_MODE_FTM &&
+ (tag == WMI_TAG_VDEV_SET_PARAM_CMD || tag == WMI_TAG_UNIT_TEST_CMD)) {
+ if (vif) {
+ arvif = (struct ath11k_vif *)vif->drv_priv;
+ *ptr = arvif->vdev_id;
+ } else {
+ ret = -EINVAL;
+ goto out;
+ }
+ }
+
ath11k_dbg(ar->ab, ATH11K_DBG_TESTMODE,
"testmode cmd wmi cmd_id %d buf length %d\n",
cmd_id, buf_len);
@@ -411,7 +442,7 @@ int ath11k_tm_cmd(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
case ATH11K_TM_CMD_TESTMODE_START:
return ath11k_tm_cmd_testmode_start(ar, tb);
case ATH11K_TM_CMD_WMI:
- return ath11k_tm_cmd_wmi(ar, tb);
+ return ath11k_tm_cmd_wmi(ar, tb, vif);
case ATH11K_TM_CMD_WMI_FTM:
set_bit(ATH11K_FLAG_FTM_SEGMENTED, &ab->dev_flags);
return ath11k_tm_cmd_process_ftm(ar, tb);
--
2.17.1
Raj Kumar Bhagat <[email protected]> writes:
> From: Venkateswara Naralasetty <[email protected]>
>
> User can extend test mode command support to set vdev and pdev params
> for debug purpose at run time by sending vdev/pdev param set command
> through the testmode command interface.
>
> Fill the proper pdev/vdev id in driver since, pdev/vdev id details may
> not be available at user space. It will make sure that the proper
> vdev/pdev ids are sent to firmware.
>
> Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
>
> Depends-On:
> [v3,3/4] wifi: ath11k: factory test mode support
>
> Signed-off-by: Venkateswara Naralasetty <[email protected]>
> Signed-off-by: Raj Kumar Bhagat <[email protected]>
> ---
Please add 'Depends-on' after the '---' line. This is for future
patches, no need to resend because of this.
--
https://patchwork.kernel.org/project/linux-wireless/list/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
On 4/26/2023 12:59 PM, Kalle Valo wrote:
> Raj Kumar Bhagat <[email protected]> writes:
>
>> From: Venkateswara Naralasetty <[email protected]>
>>
>> User can extend test mode command support to set vdev and pdev params
>> for debug purpose at run time by sending vdev/pdev param set command
>> through the testmode command interface.
>>
>> Fill the proper pdev/vdev id in driver since, pdev/vdev id details may
>> not be available at user space. It will make sure that the proper
>> vdev/pdev ids are sent to firmware.
>>
>> Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
>>
>> Depends-On:
>> [v3,3/4] wifi: ath11k: factory test mode support
>>
>> Signed-off-by: Venkateswara Naralasetty <[email protected]>
>> Signed-off-by: Raj Kumar Bhagat <[email protected]>
>> ---
>
> Please add 'Depends-on' after the '---' line. This is for future
> patches, no need to resend because of this.
>
Thanks for pointing this. Will take care for future patches.
Thanks,
Raj