2015-08-19 22:07:55

by Al Stone

[permalink] [raw]
Subject: [PATCH v2 0/5] ACPI: Provide better MADT subtable sanity checks

Currently, the BAD_MADT_ENTRY macro is used to do a very simple sanity
check on the various subtables that are defined for the MADT. The check
compares the size of the subtable data structure as defined by ACPICA to
the length entry in the subtable. If they are not the same, the assumption
is that the subtable is incorrect.

Over time, the ACPI spec has allowed for MADT subtables where this can
never be true (the local SAPIC subtable, for example). Or, more recently,
the spec has accumulated some minor flaws where there are three possible
sizes for a subtable, all of which are valid, but only for specific versions
of the spec (the GICC subtable). In both cases, BAD_MADT_ENTRY reports these
subtables as bad when they are not. In order to retain some sanity check
on the MADT subtables, we now have to special case these subtables. Of
necessity, these special cases have ended up in arch-dependent code (arm64)
or an arch has simply decided to forgo the check (ia64).

This patch set replaces the BAD_MADT_ENTRY macro with a function called
bad_madt_entry(). This function uses a data set of details about the
subtables to provide more sanity checking than before:

-- is the subtable legal for the version given in the FADT?

-- is the subtable legal for the revision of the MADT in use?

-- is the subtable of the proper length (including checking
on the one variable length subtable that is currently ignored),
given the FADT version and the MADT revision?

Further, this patch set adds in the call to bad_madt_entry() from the
acpi_table_parse_madt() function, allowing it to be used consistently
by all architectures, for all subtables, and removing the need for each
of the subtable traversal callback functions to use BAD_MADT_ENTRY.

In theory, as the ACPI specification changes, we would only have to add
additional information to the data set describing the MADT subtables in
order to continue providing sanity checks, even when new subtables are
added.

These patches have been tested on an APM Mustang (arm64) and are known to
work there. They have also been cross-compiled for x86 and ia64 with no
known failures.

Changes for v2:
-- Acked-by on 2/5 from Marc Zyngier and Catalin Marinas for ARM
-- Correct faulty end of loop test found by Timur Tabi

Al Stone (5):
ACPI: add in a bad_madt_entry() function to eventually replace the
macro
ACPI / ARM64: remove usage of BAD_MADT_ENTRY/BAD_MADT_GICC_ENTRY
ACPI / IA64: remove usage of BAD_MADT_ENTRY
ACPI / X86: remove usage of BAD_MADT_ENTRY
ACPI: remove definition of BAD_MADT_ENTRY macro

arch/arm64/include/asm/acpi.h | 8 --
arch/arm64/kernel/perf_event.c | 3 -
arch/arm64/kernel/smp.c | 2 -
arch/ia64/kernel/acpi.c | 20 ----
arch/x86/kernel/acpi/boot.c | 27 -----
drivers/acpi/tables.c | 241 +++++++++++++++++++++++++++++++++++++++++
drivers/irqchip/irq-gic-v2m.c | 2 -
drivers/irqchip/irq-gic.c | 6 -
include/linux/acpi.h | 4 -
9 files changed, 241 insertions(+), 72 deletions(-)

--
2.4.3


2015-08-19 22:08:01

by Al Stone

[permalink] [raw]
Subject: [PATCH v2 1/5] ACPI: add in a bad_madt_entry() function to eventually replace the macro

The existing BAD_MADT_ENTRY macro only checks that the size of the data
structure for an MADT subtable matches the length entry in the subtable.
This is, unfortunately, not reliable. Nor, as it turns out, does it have
anything to do with what the length should be in any particular table.

We introduce the bad_madt_entry() function that uses a data set to
do some basic sanity checks on any given MADT subtable. Over time, as
the spec changes, we should just be able to add entries to the data set
to reflect the changes.

What the data set captures is the allowed MADT subtable length for each
type of subtable, for each revision of the specification. While there
is a revision number in the MADT that we should be able to use to figure
out the proper subtable length, it was not changed when subtables did.
And, while there is a major and minor revision in the FADT that could
also help, it was not always changed as the subtables changed either.
So, the data set captures for each published version of the ACPI spec
what the FADT revisions numbers should be, the corresponding MADT
revision number, and the subtable types and lengths that were defined
at that time.

The sanity checks done are:
-- is the length non-zero?
-- is the subtable type defined/allowed for the revision of
the FADT we're using?
-- is the subtable type defined/allowed for the revision of
the MADT we're using?
-- is the length entry what it should be for this revision
of the MADT and FADT?

These checks are more thorough than the previous macro provided, and
are now insulated from data structure size changes by ACPICA, which
have been the source of other patches in the past.

Now that the bad_madt_entry() function is available, we add code to
also invoke it before any subtable handlers are called to use the
info in the subtable. Subsequent patches will remove the use of the
BAD_MADT_ENTRY macro which is now redundant as a result. Any ACPI
functions that use acpi_parse_madt_entries() will always have all of
the MADT subtables checked from now on.

Signed-off-by: Al Stone <[email protected]>
Cc: Rafael J. Wysocki <[email protected]>
Cc: Len Brown <[email protected]>
---
drivers/acpi/tables.c | 241 ++++++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 241 insertions(+)

diff --git a/drivers/acpi/tables.c b/drivers/acpi/tables.c
index 17a6fa0..d1c0efc 100644
--- a/drivers/acpi/tables.c
+++ b/drivers/acpi/tables.c
@@ -210,6 +210,245 @@ void acpi_table_print_madt_entry(struct acpi_subtable_header *header)
}
}

+/*
+ * The Long, Sad, True Story of the MADT
+ * or
+ * What does bad_madt_entry() actually do?
+ *
+ * Once upon a time in ACPI 1.0, there was the MADT. It was a nice table,
+ * and it had two subtables all of its own. But, it was also a pretty
+ * busy table, too, so over time the MADT gathered up other nice little
+ * subtables. By the time ACPI 6.0 came around, the MADT had 16 of the
+ * little guys.
+ *
+ * Now, the MADT kept a little counter around for the subtables. In fact,
+ * it kept two counters: one was the revision level, which was supposed to
+ * change when new subtables came to be, or as the ones already around grew
+ * up. The second counter was a type number, because the MADT needed a unique
+ * type for each subtable so he could tell them apart. But, sometimes the
+ * MADT got so busy, he forgot to increment the revision level when he needed
+ * to. Fortunately, the type counter kept increasing since that's the only
+ * way the MADT could find each little subtable. It just wouldn't do to have
+ * every subtable called Number 6.
+ *
+ * In the next valley over, a castle full of wizards was watching the MADT
+ * and made a pact to keep their own counter. Every time the MADT found a
+ * new subtable, or a subtable grew up, the wizards promised they would
+ * increment their counter. Well, wizards being the forgetful sort, they
+ * didn't alway do that. And, since there quite a lot of them, they
+ * couldn't always remember who was supposed to keep track of the MADT,
+ * especially if dinner was coming up soon. Their counter was called the
+ * spec version.
+ *
+ * Every now and then, the MADT would gather up all its little subtables
+ * and take them in to the cobbler to get new boots. This was a very, very
+ * meticulous cobbler, so every time they came, he wrote down all the boot
+ * sizes for all of the little subtables. The cobbler would ask each subtable
+ * for its length, check that against his careful notes, and then go get the
+ * right boots. Sometimes, a little subtable would change a bit, and their
+ * length did not match what the cobbler had written down. If the wizards
+ * or the MADT had incremented their counters, the cobbler would breath a
+ * sigh of relief and write down the new length as the right one. But, if
+ * none of the counters had changed, this would make the cobbler very, very
+ * mad. He couldn't tell if he had the right size boots or not for the
+ * little subtable. He would have to *guess* and this really bugged him.
+ *
+ * Well, when the cobbler got mad like this, he would go into hiding. He
+ * would not make or sell any boots. He would not go out at all. Pretty
+ * soon, the coffee shop would have to close because the cobbler wasn't
+ * coming by twice a day any more. Then the grocery store would have to
+ * close because he wouldn't eat much. After a while, everyone would panic
+ * and have to move from the village and go live with all their relatives
+ * (usually the ones they didn't like very much).
+ *
+ * Eventually, the cobbler would work his way out of his bad mood, and
+ * open up his boot business again. Then, everyone else could move back
+ * to the village and restart their lives, too.
+ *
+ * Fortunately, we have been able to collect up all the cobbler's careful
+ * notes (and we wrote them down below). We'll have to keep checking these
+ * notes over time, too, just as the cobbler does. But, in the meantime,
+ * we can avoid the panic and the reboot since we can make sure that each
+ * subtable is doing okay. And that's what bad_madt_entry() does.
+ *
+ *
+ * FADT Major Version -> 1 3 4 4 5 5 6
+ * FADT Minor Version -> x x x x x 1 0
+ * MADT revision -> 1 1 2 3 3 3 3
+ * Spec Version -> 1.0 2.0 3.0b 4.0a 5.0b 5.1a 6.0
+ * Subtable Name Type Expected Length ->
+ * Processor Local APIC 0x0 8 8 8 8 8 8 8
+ * IO APIC 0x1 12 12 12 12 12 12 12
+ * Int Src Override 0x2 10 10 10 10 10 10
+ * NMI Src 0x3 8 8 8 8 8 8
+ * Local APIC NMI Struct 0x4 6 6 6 6 6 6
+ * Local APIC Addr Ovrrd 0x5 16 12 12 12 12 12
+ * IO SAPIC 0x6 20 16 16 16 16 16
+ * Local SAPIC 0x7 8 >16 >16 >16 >16 >16
+ * Platform Int Src 0x8 16 16 16 16 16 16
+ * Proc Local x2APIC 0x9 16 16 16 16
+ * Local x2APIC NMI 0xa 12 12 12 12
+ * GICC CPU I/F 0xb 40 76 80
+ * GICD 0xc 24 24 24
+ * GICv2m MSI 0xd 24 24
+ * GICR 0xe 16 16
+ * GIC ITS 0xf 16
+ *
+ * In the table, each length entry is what should be in the length
+ * field of the subtable, and -- in general -- it should match the
+ * size of the struct for the subtable. Any value that is not set
+ * (i.e., is zero) indicates that the subtable is not defined for
+ * that version of the ACPI spec.
+ *
+ */
+#define SUBTABLE_UNDEFINED 0x00
+#define SUBTABLE_VARIABLE 0xff
+#define NUM_SUBTABLE_TYPES 16
+
+struct acpi_madt_subtable_lengths {
+ unsigned short major_version; /* from revision in FADT header */
+ unsigned short minor_version; /* FADT field starting with 5.1 */
+ unsigned short madt_version; /* MADT revision */
+ unsigned short num_types; /* types possible for this version */
+ unsigned short lengths[NUM_SUBTABLE_TYPES];
+ /* subtable lengths, indexed by type */
+};
+
+static struct acpi_madt_subtable_lengths spec_info[] = {
+ { /* for ACPI 1.0 */
+ .major_version = 1,
+ .minor_version = 0,
+ .madt_version = 1,
+ .num_types = 2,
+ .lengths = { 8, 12 }
+ },
+ { /* for ACPI 2.0 */
+ .major_version = 3,
+ .minor_version = 0,
+ .madt_version = 1,
+ .num_types = 9,
+ .lengths = { 8, 12, 10, 8, 6, 16, 20, 8, 16 }
+ },
+ { /* for ACPI 3.0b */
+ .major_version = 4,
+ .minor_version = 0,
+ .madt_version = 2,
+ .num_types = 9,
+ .lengths = { 8, 12, 10, 8, 6, 12, 16, SUBTABLE_VARIABLE, 16 }
+ },
+ { /* for ACPI 4.0a */
+ .major_version = 4,
+ .minor_version = 0,
+ .madt_version = 3,
+ .num_types = 11,
+ .lengths = { 8, 12, 10, 8, 6, 12, 16, SUBTABLE_VARIABLE,
+ 16, 16, 12 }
+ },
+ { /* for ACPI 5.0b */
+ .major_version = 5,
+ .minor_version = 0,
+ .madt_version = 3,
+ .num_types = 13,
+ .lengths = { 8, 12, 10, 8, 6, 12, 16, SUBTABLE_VARIABLE,
+ 16, 16, 12, 40, 24 }
+ },
+ { /* for ACPI 5.1a */
+ .major_version = 5,
+ .minor_version = 1,
+ .madt_version = 3,
+ .num_types = 15,
+ .lengths = { 8, 12, 10, 8, 6, 12, 16, SUBTABLE_VARIABLE,
+ 16, 16, 12, 76, 24, 24, 16 }
+ },
+ { /* for ACPI 6.0 */
+ .major_version = 6,
+ .minor_version = 0,
+ .madt_version = 3,
+ .num_types = 16,
+ .lengths = { 8, 12, 10, 8, 6, 12, 16, SUBTABLE_VARIABLE,
+ 16, 16, 12, 80, 24, 24, 16, 16 }
+ },
+ { /* terminator */
+ .major_version = 0,
+ .minor_version = 0,
+ .madt_version = 0,
+ .num_types = 0,
+ .lengths = { 0 }
+ }
+};
+
+int __init bad_madt_entry(struct acpi_table_header *table,
+ struct acpi_subtable_header *entry)
+{
+ struct acpi_madt_subtable_lengths *ms;
+ struct acpi_table_madt *madt;
+ unsigned short major;
+ unsigned short minor;
+ unsigned short len;
+
+ /* simple sanity checking on MADT subtable entries */
+ if (!entry || !table)
+ return 1;
+
+ /* FADT minor numbers were not introduced until ACPI 5.1 */
+ major = acpi_gbl_FADT.header.revision;
+ if (major >= 5 && acpi_gbl_FADT.header.length >= 268)
+ minor = acpi_gbl_FADT.minor_revision;
+ else
+ minor = 0;
+
+ madt = (struct acpi_table_madt *)table;
+ ms = spec_info;
+ while (ms->num_types != 0) {
+ if (ms->major_version == major &&
+ ms->minor_version == minor &&
+ ms->madt_version == madt->header.revision)
+ break;
+ ms++;
+ }
+ if (!ms->num_types) {
+ pr_err("undefined FADT version: %d.%d\n", major, minor);
+ return 1;
+ }
+
+ if (entry->type >= ms->num_types) {
+ pr_err("undefined MADT subtable type for FADT %d.%d: %d (length %d)\n",
+ major, minor, entry->type, entry->length);
+ return 1;
+ }
+
+ /* verify that the table is allowed for this version of the spec */
+ len = ms->lengths[entry->type];
+ if (!len) {
+ pr_err("MADT subtable %d not defined for FADT %d.%d\n",
+ entry->type, major, minor);
+ return 1;
+ }
+
+ /* verify that the length is what we expect */
+ if (len == SUBTABLE_VARIABLE) {
+ if (entry->type == ACPI_MADT_TYPE_LOCAL_SAPIC) {
+ struct acpi_madt_local_sapic *lsapic =
+ (struct acpi_madt_local_sapic *)entry;
+
+ if (sizeof(struct acpi_madt_local_sapic) +
+ strlen(lsapic->uid_string) + 1 != entry->length) {
+ pr_err("Variable length MADT subtable %d is wrong size: %d\n",
+ entry->type, entry->length);
+ return 1;
+ }
+ }
+ } else {
+ if (entry->length != len) {
+ pr_err("MADT subtable %d is wrong size: %d\n",
+ len, entry->type);
+ return 1;
+ }
+ }
+
+ return 0;
+}
+
int __init
acpi_parse_entries(char *id, unsigned long table_size,
acpi_tbl_entry_handler handler,
@@ -245,6 +484,8 @@ acpi_parse_entries(char *id, unsigned long table_size,
table_end) {
if (entry->type == entry_id
&& (!max_entries || count < max_entries)) {
+ if (bad_madt_entry(table_header, entry))
+ return -EINVAL;
if (handler(entry, table_end))
return -EINVAL;

--
2.4.3

2015-08-19 22:09:25

by Al Stone

[permalink] [raw]
Subject: [PATCH v2 2/5] ACPI / ARM64: remove usage of BAD_MADT_ENTRY/BAD_MADT_GICC_ENTRY

Now that we have introduced the bad_madt_entry() function, and that
function is being invoked in acpi_table_parse_madt() for us, there
is no longer any need to use the BAD_MADT_ENTRY macro, or in the case
of arm64, the BAD_MADT_GICC_ENTRY, too.

Signed-off-by: Al Stone <[email protected]>
Acked-by: Catalin Marinas <[email protected]>
Acked-by: Marc Zyngier <[email protected]>
Cc: Will Deacon <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Jason Cooper <[email protected]>
---
arch/arm64/include/asm/acpi.h | 8 --------
arch/arm64/kernel/smp.c | 2 --
drivers/irqchip/irq-gic.c | 6 ------
3 files changed, 16 deletions(-)

diff --git a/arch/arm64/include/asm/acpi.h b/arch/arm64/include/asm/acpi.h
index 208cec0..ed7e212 100644
--- a/arch/arm64/include/asm/acpi.h
+++ b/arch/arm64/include/asm/acpi.h
@@ -19,14 +19,6 @@
#include <asm/cputype.h>
#include <asm/smp_plat.h>

-/* Macros for consistency checks of the GICC subtable of MADT */
-#define ACPI_MADT_GICC_LENGTH \
- (acpi_gbl_FADT.header.revision < 6 ? 76 : 80)
-
-#define BAD_MADT_GICC_ENTRY(entry, end) \
- (!(entry) || (unsigned long)(entry) + sizeof(*(entry)) > (end) || \
- (entry)->header.length != ACPI_MADT_GICC_LENGTH)
-
/* Basic configuration for ACPI */
#ifdef CONFIG_ACPI
/* ACPI table mapping after acpi_gbl_permanent_mmap is set */
diff --git a/arch/arm64/kernel/smp.c b/arch/arm64/kernel/smp.c
index dbdaacd..66cc8c4 100644
--- a/arch/arm64/kernel/smp.c
+++ b/arch/arm64/kernel/smp.c
@@ -451,8 +451,6 @@ acpi_parse_gic_cpu_interface(struct acpi_subtable_header *header,
struct acpi_madt_generic_interrupt *processor;

processor = (struct acpi_madt_generic_interrupt *)header;
- if (BAD_MADT_GICC_ENTRY(processor, end))
- return -EINVAL;

acpi_table_print_madt_entry(header);

diff --git a/drivers/irqchip/irq-gic.c b/drivers/irqchip/irq-gic.c
index aa3e7b8..848c44c 100644
--- a/drivers/irqchip/irq-gic.c
+++ b/drivers/irqchip/irq-gic.c
@@ -1064,9 +1064,6 @@ gic_acpi_parse_madt_cpu(struct acpi_subtable_header *header,

processor = (struct acpi_madt_generic_interrupt *)header;

- if (BAD_MADT_GICC_ENTRY(processor, end))
- return -EINVAL;
-
/*
* There is no support for non-banked GICv1/2 register in ACPI spec.
* All CPU interface addresses have to be the same.
@@ -1088,9 +1085,6 @@ gic_acpi_parse_madt_distributor(struct acpi_subtable_header *header,

dist = (struct acpi_madt_generic_distributor *)header;

- if (BAD_MADT_ENTRY(dist, end))
- return -EINVAL;
-
dist_phy_base = dist->base_address;
return 0;
}
--
2.4.3

2015-08-19 22:09:01

by Al Stone

[permalink] [raw]
Subject: [PATCH v2 3/5] ACPI / IA64: remove usage of BAD_MADT_ENTRY

Now that we have introduced the bad_madt_entry() function, and that
function is being invoked in acpi_table_parse_madt() for us, there
is no longer any need to use the BAD_MADT_ENTRY macro.

Signed-off-by: Al Stone <[email protected]>
Cc: Tony Luck <[email protected]>
Cc: Fenghua Yu <[email protected]>
---
arch/ia64/kernel/acpi.c | 20 --------------------
1 file changed, 20 deletions(-)

diff --git a/arch/ia64/kernel/acpi.c b/arch/ia64/kernel/acpi.c
index b1698bc..efa3f0a 100644
--- a/arch/ia64/kernel/acpi.c
+++ b/arch/ia64/kernel/acpi.c
@@ -184,9 +184,6 @@ acpi_parse_lapic_addr_ovr(struct acpi_subtable_header * header,

lapic = (struct acpi_madt_local_apic_override *)header;

- if (BAD_MADT_ENTRY(lapic, end))
- return -EINVAL;
-
if (lapic->address) {
iounmap(ipi_base_addr);
ipi_base_addr = ioremap(lapic->address, 0);
@@ -201,8 +198,6 @@ acpi_parse_lsapic(struct acpi_subtable_header * header, const unsigned long end)

lsapic = (struct acpi_madt_local_sapic *)header;

- /*Skip BAD_MADT_ENTRY check, as lsapic size could vary */
-
if (lsapic->lapic_flags & ACPI_MADT_ENABLED) {
#ifdef CONFIG_SMP
smp_boot_data.cpu_phys_id[available_cpus] =
@@ -222,9 +217,6 @@ acpi_parse_lapic_nmi(struct acpi_subtable_header * header, const unsigned long e

lacpi_nmi = (struct acpi_madt_local_apic_nmi *)header;

- if (BAD_MADT_ENTRY(lacpi_nmi, end))
- return -EINVAL;
-
/* TBD: Support lapic_nmi entries */
return 0;
}
@@ -236,9 +228,6 @@ acpi_parse_iosapic(struct acpi_subtable_header * header, const unsigned long end

iosapic = (struct acpi_madt_io_sapic *)header;

- if (BAD_MADT_ENTRY(iosapic, end))
- return -EINVAL;
-
return iosapic_init(iosapic->address, iosapic->global_irq_base);
}

@@ -253,9 +242,6 @@ acpi_parse_plat_int_src(struct acpi_subtable_header * header,

plintsrc = (struct acpi_madt_interrupt_source *)header;

- if (BAD_MADT_ENTRY(plintsrc, end))
- return -EINVAL;
-
/*
* Get vector assignment for this interrupt, set attributes,
* and program the IOSAPIC routing table.
@@ -336,9 +322,6 @@ acpi_parse_int_src_ovr(struct acpi_subtable_header * header,

p = (struct acpi_madt_interrupt_override *)header;

- if (BAD_MADT_ENTRY(p, end))
- return -EINVAL;
-
iosapic_override_isa_irq(p->source_irq, p->global_irq,
((p->inti_flags & ACPI_MADT_POLARITY_MASK) ==
ACPI_MADT_POLARITY_ACTIVE_LOW) ?
@@ -356,9 +339,6 @@ acpi_parse_nmi_src(struct acpi_subtable_header * header, const unsigned long end

nmi_src = (struct acpi_madt_nmi_source *)header;

- if (BAD_MADT_ENTRY(nmi_src, end))
- return -EINVAL;
-
/* TBD: Support nimsrc entries */
return 0;
}
--
2.4.3

2015-08-19 22:08:33

by Al Stone

[permalink] [raw]
Subject: [PATCH v2 4/5] ACPI / X86: remove usage of BAD_MADT_ENTRY

Now that we have introduced the bad_madt_entry() function, and that
function is being invoked in acpi_table_parse_madt() for us, there
is no longer any need to use the BAD_MADT_ENTRY macro.

Signed-off-by: Al Stone <[email protected]>
Cc: Rafael J. Wysocki <[email protected]>
Cc: Len Brown <[email protected]>
Cc: Pavel Machek <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: H. Peter Anvin <[email protected]>
Cc: [email protected]
---
arch/x86/kernel/acpi/boot.c | 27 ---------------------------
1 file changed, 27 deletions(-)

diff --git a/arch/x86/kernel/acpi/boot.c b/arch/x86/kernel/acpi/boot.c
index 75e8bad..f2a70b2 100644
--- a/arch/x86/kernel/acpi/boot.c
+++ b/arch/x86/kernel/acpi/boot.c
@@ -194,9 +194,6 @@ acpi_parse_x2apic(struct acpi_subtable_header *header, const unsigned long end)

processor = (struct acpi_madt_local_x2apic *)header;

- if (BAD_MADT_ENTRY(processor, end))
- return -EINVAL;
-
acpi_table_print_madt_entry(header);

apic_id = processor->local_apic_id;
@@ -227,9 +224,6 @@ acpi_parse_lapic(struct acpi_subtable_header * header, const unsigned long end)

processor = (struct acpi_madt_local_apic *)header;

- if (BAD_MADT_ENTRY(processor, end))
- return -EINVAL;
-
acpi_table_print_madt_entry(header);

/*
@@ -252,9 +246,6 @@ acpi_parse_sapic(struct acpi_subtable_header *header, const unsigned long end)

processor = (struct acpi_madt_local_sapic *)header;

- if (BAD_MADT_ENTRY(processor, end))
- return -EINVAL;
-
acpi_table_print_madt_entry(header);

acpi_register_lapic((processor->id << 8) | processor->eid,/* APIC ID */
@@ -271,9 +262,6 @@ acpi_parse_lapic_addr_ovr(struct acpi_subtable_header * header,

lapic_addr_ovr = (struct acpi_madt_local_apic_override *)header;

- if (BAD_MADT_ENTRY(lapic_addr_ovr, end))
- return -EINVAL;
-
acpi_lapic_addr = lapic_addr_ovr->address;

return 0;
@@ -287,9 +275,6 @@ acpi_parse_x2apic_nmi(struct acpi_subtable_header *header,

x2apic_nmi = (struct acpi_madt_local_x2apic_nmi *)header;

- if (BAD_MADT_ENTRY(x2apic_nmi, end))
- return -EINVAL;
-
acpi_table_print_madt_entry(header);

if (x2apic_nmi->lint != 1)
@@ -305,9 +290,6 @@ acpi_parse_lapic_nmi(struct acpi_subtable_header * header, const unsigned long e

lapic_nmi = (struct acpi_madt_local_apic_nmi *)header;

- if (BAD_MADT_ENTRY(lapic_nmi, end))
- return -EINVAL;
-
acpi_table_print_madt_entry(header);

if (lapic_nmi->lint != 1)
@@ -411,9 +393,6 @@ acpi_parse_ioapic(struct acpi_subtable_header * header, const unsigned long end)

ioapic = (struct acpi_madt_io_apic *)header;

- if (BAD_MADT_ENTRY(ioapic, end))
- return -EINVAL;
-
acpi_table_print_madt_entry(header);

/* Statically assign IRQ numbers for IOAPICs hosting legacy IRQs */
@@ -462,9 +441,6 @@ acpi_parse_int_src_ovr(struct acpi_subtable_header * header,

intsrc = (struct acpi_madt_interrupt_override *)header;

- if (BAD_MADT_ENTRY(intsrc, end))
- return -EINVAL;
-
acpi_table_print_madt_entry(header);

if (intsrc->source_irq == acpi_gbl_FADT.sci_interrupt) {
@@ -503,9 +479,6 @@ acpi_parse_nmi_src(struct acpi_subtable_header * header, const unsigned long end

nmi_src = (struct acpi_madt_nmi_source *)header;

- if (BAD_MADT_ENTRY(nmi_src, end))
- return -EINVAL;
-
acpi_table_print_madt_entry(header);

/* TBD: Support nimsrc entries? */
--
2.4.3

2015-08-19 22:08:09

by Al Stone

[permalink] [raw]
Subject: [PATCH v2 5/5] ACPI: remove definition of BAD_MADT_ENTRY macro

Now that we have introduced to bad_madt_entry(), and we have removed
all the usages of the BAD_MADT_ENTRY macro from all of the various
architectures that use it (arm64, ia64, x86), we can remove the macro
definition since it is no longer used.

Signed-off-by: Al Stone <[email protected]>
Cc: Rafael J. Wysocki <[email protected]>
Cc: Len Brown <[email protected]>
---
include/linux/acpi.h | 4 ----
1 file changed, 4 deletions(-)

diff --git a/include/linux/acpi.h b/include/linux/acpi.h
index 01e6770..96729d3 100644
--- a/include/linux/acpi.h
+++ b/include/linux/acpi.h
@@ -127,10 +127,6 @@ static inline void acpi_initrd_override(void *data, size_t size)
}
#endif

-#define BAD_MADT_ENTRY(entry, end) ( \
- (!entry) || (unsigned long)entry + sizeof(*entry) > end || \
- ((struct acpi_subtable_header *)entry)->length < sizeof(*entry))
-
char * __acpi_map_table (unsigned long phys_addr, unsigned long size);
void __acpi_unmap_table(char *map, unsigned long size);
int early_acpi_boot_init(void);
--
2.4.3

2015-08-20 10:13:30

by Will Deacon

[permalink] [raw]
Subject: Re: [PATCH v2 2/5] ACPI / ARM64: remove usage of BAD_MADT_ENTRY/BAD_MADT_GICC_ENTRY

Hi Al,

On Wed, Aug 19, 2015 at 11:07:25PM +0100, Al Stone wrote:
> Now that we have introduced the bad_madt_entry() function, and that
> function is being invoked in acpi_table_parse_madt() for us, there
> is no longer any need to use the BAD_MADT_ENTRY macro, or in the case
> of arm64, the BAD_MADT_GICC_ENTRY, too.
>
> Signed-off-by: Al Stone <[email protected]>
> Acked-by: Catalin Marinas <[email protected]>
> Acked-by: Marc Zyngier <[email protected]>
> Cc: Will Deacon <[email protected]>
> Cc: Thomas Gleixner <[email protected]>
> Cc: Jason Cooper <[email protected]>
> ---
> arch/arm64/include/asm/acpi.h | 8 --------
> arch/arm64/kernel/smp.c | 2 --
> drivers/irqchip/irq-gic.c | 6 ------
> 3 files changed, 16 deletions(-)

How are you planning to merge this (and which kernel are you targetting?)
You've got Acks for both arm64 and irqchip, so I guess either of those
trees could take it.

Will

2015-08-20 16:57:10

by Al Stone

[permalink] [raw]
Subject: Re: [PATCH v2 2/5] ACPI / ARM64: remove usage of BAD_MADT_ENTRY/BAD_MADT_GICC_ENTRY

On 08/20/2015 04:13 AM, Will Deacon wrote:
> Hi Al,
>
> On Wed, Aug 19, 2015 at 11:07:25PM +0100, Al Stone wrote:
>> Now that we have introduced the bad_madt_entry() function, and that
>> function is being invoked in acpi_table_parse_madt() for us, there
>> is no longer any need to use the BAD_MADT_ENTRY macro, or in the case
>> of arm64, the BAD_MADT_GICC_ENTRY, too.
>>
>> Signed-off-by: Al Stone <[email protected]>
>> Acked-by: Catalin Marinas <[email protected]>
>> Acked-by: Marc Zyngier <[email protected]>
>> Cc: Will Deacon <[email protected]>
>> Cc: Thomas Gleixner <[email protected]>
>> Cc: Jason Cooper <[email protected]>
>> ---
>> arch/arm64/include/asm/acpi.h | 8 --------
>> arch/arm64/kernel/smp.c | 2 --
>> drivers/irqchip/irq-gic.c | 6 ------
>> 3 files changed, 16 deletions(-)
>
> How are you planning to merge this (and which kernel are you targetting?)
> You've got Acks for both arm64 and irqchip, so I guess either of those
> trees could take it.

Yeah, this is a little messy. If I can get into 4.2, that would be nice,
but not required -- arm64 already has a usable patch for now, and that's
the only arch affected. So, 4.3 was my primary target (which is why I
worked with linux-next for these).

Which tree? Yeesh. 1/5 and 5/5 are ACPI only and required for the rest
to work properly; 2/5 is arm64, 3/5 is ia64, and 4/5 is x86. ARM folks are
the only ones to have provided acks or reviews, however. I guess I was
assuming this would have to go in via Rafael's ACPI tree since those are
the key parts -- the arch-specific patches would remove safety checks on
MADT subtables without replacing them, if they went in before the ACPI
patches.

Does that make sense? What do you think?

--
ciao,
al
-----------------------------------
Al Stone
Software Engineer
Red Hat, Inc.
[email protected]
-----------------------------------

2015-08-24 10:04:33

by Will Deacon

[permalink] [raw]
Subject: Re: [PATCH v2 2/5] ACPI / ARM64: remove usage of BAD_MADT_ENTRY/BAD_MADT_GICC_ENTRY

On Thu, Aug 20, 2015 at 05:57:05PM +0100, Al Stone wrote:
> On 08/20/2015 04:13 AM, Will Deacon wrote:
> > On Wed, Aug 19, 2015 at 11:07:25PM +0100, Al Stone wrote:
> >> Now that we have introduced the bad_madt_entry() function, and that
> >> function is being invoked in acpi_table_parse_madt() for us, there
> >> is no longer any need to use the BAD_MADT_ENTRY macro, or in the case
> >> of arm64, the BAD_MADT_GICC_ENTRY, too.
> >>
> >> Signed-off-by: Al Stone <[email protected]>
> >> Acked-by: Catalin Marinas <[email protected]>
> >> Acked-by: Marc Zyngier <[email protected]>
> >> Cc: Will Deacon <[email protected]>
> >> Cc: Thomas Gleixner <[email protected]>
> >> Cc: Jason Cooper <[email protected]>
> >> ---
> >> arch/arm64/include/asm/acpi.h | 8 --------
> >> arch/arm64/kernel/smp.c | 2 --
> >> drivers/irqchip/irq-gic.c | 6 ------
> >> 3 files changed, 16 deletions(-)
> >
> > How are you planning to merge this (and which kernel are you targetting?)
> > You've got Acks for both arm64 and irqchip, so I guess either of those
> > trees could take it.
>
> Yeah, this is a little messy. If I can get into 4.2, that would be nice,
> but not required -- arm64 already has a usable patch for now, and that's
> the only arch affected. So, 4.3 was my primary target (which is why I
> worked with linux-next for these).
>
> Which tree? Yeesh. 1/5 and 5/5 are ACPI only and required for the rest
> to work properly; 2/5 is arm64, 3/5 is ia64, and 4/5 is x86. ARM folks are
> the only ones to have provided acks or reviews, however. I guess I was
> assuming this would have to go in via Rafael's ACPI tree since those are
> the key parts -- the arch-specific patches would remove safety checks on
> MADT subtables without replacing them, if they went in before the ACPI
> patches.
>
> Does that make sense? What do you think?

Yup, taking it all via Rafael is fine by me. I just didn't want to end
up in a situation where you thought something was going via the arm64
tree but I hadn't queued it.

Will

2015-08-26 15:38:48

by Timur Tabi

[permalink] [raw]
Subject: Re: [PATCH v2 1/5] ACPI: add in a bad_madt_entry() function to eventually replace the macro

On Wed, Aug 19, 2015 at 5:07 PM, Al Stone <[email protected]> wrote:
> + pr_err("Variable length MADT subtable %d is wrong size: %d\n",
> + entry->type, entry->length);
> + return 1;
> + }
> + }
> + } else {
> + if (entry->length != len) {
> + pr_err("MADT subtable %d is wrong size: %d\n",
> + len, entry->type);

Can we make these a little more descriptive?

pr_err("Variable length MADT subtable type %d is wrong size: %d,
should be %d\n",
entry->type, entry->length, len);

pr_err("MADT subtable type %d is wrong size: %d, should be %d\n",
entry->type, entry->length, len);




--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project.

2015-08-26 20:30:32

by Al Stone

[permalink] [raw]
Subject: Re: [PATCH v2 1/5] ACPI: add in a bad_madt_entry() function to eventually replace the macro

On 08/26/2015 09:38 AM, Timur Tabi wrote:
> On Wed, Aug 19, 2015 at 5:07 PM, Al Stone <[email protected]> wrote:
>> + pr_err("Variable length MADT subtable %d is wrong size: %d\n",
>> + entry->type, entry->length);
>> + return 1;
>> + }
>> + }
>> + } else {
>> + if (entry->length != len) {
>> + pr_err("MADT subtable %d is wrong size: %d\n",
>> + len, entry->type);
>
> Can we make these a little more descriptive?
>
> pr_err("Variable length MADT subtable type %d is wrong size: %d,
> should be %d\n",
> entry->type, entry->length, len);
>
> pr_err("MADT subtable type %d is wrong size: %d, should be %d\n",
> entry->type, entry->length, len);
>

Sure. It's always a fine line between verbose and not enough info.

--
ciao,
al
-----------------------------------
Al Stone
Software Engineer
Red Hat, Inc.
[email protected]
-----------------------------------