2020-03-13 01:12:06

by Sowjanya Komatineni

[permalink] [raw]
Subject: [PATCH v1 2/3] mmc: tegra: Implement HW busy wait timeout based on command busy time

Tegra host supports HW busy detection and timeouts based on the
count programmed in SDHCI_TIMEOUT_CONTROL register and max busy
timeout it supports is 11s in finite busy wait mode.

Some operations like SLEEP_AWAKE, ERASE and flush cache through
SWITCH commands take longer than 11s and Tegra host supports
infinite HW busy wait mode where HW waits forever till the card
is busy without HW timeout.

This patch implements Tegra specific set_timeout sdhci_ops to allow
switching between finite and infinite HW busy detection wait modes
based on the device command expected operation time.

Signed-off-by: Sowjanya Komatineni <[email protected]>
---
drivers/mmc/host/sdhci-tegra.c | 31 +++++++++++++++++++++++++++++++
1 file changed, 31 insertions(+)

diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
index 403ac44..40a221d 100644
--- a/drivers/mmc/host/sdhci-tegra.c
+++ b/drivers/mmc/host/sdhci-tegra.c
@@ -45,6 +45,7 @@
#define SDHCI_TEGRA_CAP_OVERRIDES_DQS_TRIM_SHIFT 8

#define SDHCI_TEGRA_VENDOR_MISC_CTRL 0x120
+#define SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT BIT(0)
#define SDHCI_MISC_CTRL_ENABLE_SDR104 0x8
#define SDHCI_MISC_CTRL_ENABLE_SDR50 0x10
#define SDHCI_MISC_CTRL_ENABLE_SDHCI_SPEC_300 0x20
@@ -1227,6 +1228,34 @@ static u32 sdhci_tegra_cqhci_irq(struct sdhci_host *host, u32 intmask)
return 0;
}

+static void tegra_sdhci_set_timeout(struct sdhci_host *host,
+ struct mmc_command *cmd)
+{
+ u32 val;
+
+ /*
+ * HW busy detection timeout is based on programmed data timeout
+ * counter and maximum supported timeout is 11s which may not be
+ * enough for long operations like cache flush, sleep awake, erase.
+ *
+ * ERASE_TIMEOUT_LIMIT bit of VENDOR_MISC_CTRL register allows
+ * host controller to wait for busy state until the card is busy
+ * without HW timeout.
+ *
+ * So, use infinite busy wait mode for operations that may take
+ * more than maximum HW busy timeout of 11s otherwise use finite
+ * busy wait mode.
+ */
+ val = sdhci_readl(host, SDHCI_TEGRA_VENDOR_MISC_CTRL);
+ if (cmd && cmd->busy_timeout >= 11 * HZ)
+ val |= SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT;
+ else
+ val &= ~SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT;
+ sdhci_writel(host, val, SDHCI_TEGRA_VENDOR_MISC_CTRL);
+
+ __sdhci_set_timeout(host, cmd);
+}
+
static const struct cqhci_host_ops sdhci_tegra_cqhci_ops = {
.write_l = tegra_cqhci_writel,
.enable = sdhci_tegra_cqe_enable,
@@ -1366,6 +1395,7 @@ static const struct sdhci_ops tegra210_sdhci_ops = {
.set_uhs_signaling = tegra_sdhci_set_uhs_signaling,
.voltage_switch = tegra_sdhci_voltage_switch,
.get_max_clock = tegra_sdhci_get_max_clock,
+ .set_timeout = tegra_sdhci_set_timeout,
};

static const struct sdhci_pltfm_data sdhci_tegra210_pdata = {
@@ -1403,6 +1433,7 @@ static const struct sdhci_ops tegra186_sdhci_ops = {
.voltage_switch = tegra_sdhci_voltage_switch,
.get_max_clock = tegra_sdhci_get_max_clock,
.irq = sdhci_tegra_cqhci_irq,
+ .set_timeout = tegra_sdhci_set_timeout,
};

static const struct sdhci_pltfm_data sdhci_tegra186_pdata = {
--
2.7.4


2020-03-17 09:53:20

by Adrian Hunter

[permalink] [raw]
Subject: Re: [PATCH v1 2/3] mmc: tegra: Implement HW busy wait timeout based on command busy time

On 10/03/20 2:13 am, Sowjanya Komatineni wrote:
> Tegra host supports HW busy detection and timeouts based on the
> count programmed in SDHCI_TIMEOUT_CONTROL register and max busy
> timeout it supports is 11s in finite busy wait mode.
>
> Some operations like SLEEP_AWAKE, ERASE and flush cache through
> SWITCH commands take longer than 11s and Tegra host supports
> infinite HW busy wait mode where HW waits forever till the card
> is busy without HW timeout.
>
> This patch implements Tegra specific set_timeout sdhci_ops to allow
> switching between finite and infinite HW busy detection wait modes
> based on the device command expected operation time.
>
> Signed-off-by: Sowjanya Komatineni <[email protected]>
> ---
> drivers/mmc/host/sdhci-tegra.c | 31 +++++++++++++++++++++++++++++++

Acked-by: Adrian Hunter <[email protected]>

> 1 file changed, 31 insertions(+)
>
> diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
> index 403ac44..40a221d 100644
> --- a/drivers/mmc/host/sdhci-tegra.c
> +++ b/drivers/mmc/host/sdhci-tegra.c
> @@ -45,6 +45,7 @@
> #define SDHCI_TEGRA_CAP_OVERRIDES_DQS_TRIM_SHIFT 8
>
> #define SDHCI_TEGRA_VENDOR_MISC_CTRL 0x120
> +#define SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT BIT(0)
> #define SDHCI_MISC_CTRL_ENABLE_SDR104 0x8
> #define SDHCI_MISC_CTRL_ENABLE_SDR50 0x10
> #define SDHCI_MISC_CTRL_ENABLE_SDHCI_SPEC_300 0x20
> @@ -1227,6 +1228,34 @@ static u32 sdhci_tegra_cqhci_irq(struct sdhci_host *host, u32 intmask)
> return 0;
> }
>
> +static void tegra_sdhci_set_timeout(struct sdhci_host *host,
> + struct mmc_command *cmd)
> +{
> + u32 val;
> +
> + /*
> + * HW busy detection timeout is based on programmed data timeout
> + * counter and maximum supported timeout is 11s which may not be
> + * enough for long operations like cache flush, sleep awake, erase.
> + *
> + * ERASE_TIMEOUT_LIMIT bit of VENDOR_MISC_CTRL register allows
> + * host controller to wait for busy state until the card is busy
> + * without HW timeout.
> + *
> + * So, use infinite busy wait mode for operations that may take
> + * more than maximum HW busy timeout of 11s otherwise use finite
> + * busy wait mode.
> + */
> + val = sdhci_readl(host, SDHCI_TEGRA_VENDOR_MISC_CTRL);
> + if (cmd && cmd->busy_timeout >= 11 * HZ)
> + val |= SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT;
> + else
> + val &= ~SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT;
> + sdhci_writel(host, val, SDHCI_TEGRA_VENDOR_MISC_CTRL);
> +
> + __sdhci_set_timeout(host, cmd);
> +}
> +
> static const struct cqhci_host_ops sdhci_tegra_cqhci_ops = {
> .write_l = tegra_cqhci_writel,
> .enable = sdhci_tegra_cqe_enable,
> @@ -1366,6 +1395,7 @@ static const struct sdhci_ops tegra210_sdhci_ops = {
> .set_uhs_signaling = tegra_sdhci_set_uhs_signaling,
> .voltage_switch = tegra_sdhci_voltage_switch,
> .get_max_clock = tegra_sdhci_get_max_clock,
> + .set_timeout = tegra_sdhci_set_timeout,
> };
>
> static const struct sdhci_pltfm_data sdhci_tegra210_pdata = {
> @@ -1403,6 +1433,7 @@ static const struct sdhci_ops tegra186_sdhci_ops = {
> .voltage_switch = tegra_sdhci_voltage_switch,
> .get_max_clock = tegra_sdhci_get_max_clock,
> .irq = sdhci_tegra_cqhci_irq,
> + .set_timeout = tegra_sdhci_set_timeout,
> };
>
> static const struct sdhci_pltfm_data sdhci_tegra186_pdata = {
>