From: Rafał Miłecki <[email protected]>
They were named incorrectly most likely due to copy & paste mistake.
Signed-off-by: Rafał Miłecki <[email protected]>
---
arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts b/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts
index 2f4a651..93cc91d 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts
+++ b/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts
@@ -31,13 +31,13 @@
};
lan3 {
- label = "bcm53xx:green:lan1";
+ label = "bcm53xx:green:lan3";
gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
linux,default-trigger = "default-off";
};
lan4 {
- label = "bcm53xx:green:lan0";
+ label = "bcm53xx:green:lan4";
gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
linux,default-trigger = "default-off";
};
@@ -49,7 +49,7 @@
};
lan1 {
- label = "bcm53xx:green:lan3";
+ label = "bcm53xx:green:lan1";
gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
linux,default-trigger = "default-off";
};
--
2.10.1
From: Rafał Miłecki <[email protected]>
There are 3 separated controllers, one per USB /standard/. With PHY
drivers in place they can be simply supported with generic drivers.
Signed-off-by: Rafał Miłecki <[email protected]>
---
arch/arm/boot/dts/bcm5301x.dtsi | 33 ++++++++++++++++++++++++++++++++-
1 file changed, 32 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
index f09a2bb..bfc98d19 100644
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/bcm5301x.dtsi
@@ -248,8 +248,26 @@
#address-cells = <1>;
#size-cells = <1>;
+ ranges;
- phys = <&usb2_phy>;
+ interrupt-parent = <&gic>;
+
+ ohci: ohci@21000 {
+ #usb-cells = <0>;
+
+ compatible = "generic-ohci";
+ reg = <0x00022000 0x1000>;
+ interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ ehci: ehci@22000 {
+ #usb-cells = <0>;
+
+ compatible = "generic-ehci";
+ reg = <0x00021000 0x1000>;
+ interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb2_phy>;
+ };
};
usb3: usb3@23000 {
@@ -257,6 +275,19 @@
#address-cells = <1>;
#size-cells = <1>;
+ ranges;
+
+ interrupt-parent = <&gic>;
+
+ xhci: xhci@23000 {
+ #usb-cells = <0>;
+
+ compatible = "generic-xhci";
+ reg = <0x00023000 0x1000>;
+ interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb3_phy>;
+ phy-names = "usb";
+ };
};
spi@29000 {
--
2.10.1
From: Rafał Miłecki <[email protected]>
So far we were specifying only the first block which is always limited
up to 128 MiB. There are many devices with 256 MiB and few with 512 MiB.
Signed-off-by: Rafał Miłecki <[email protected]>
---
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts | 3 ++-
arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts | 3 ++-
arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts | 3 ++-
arch/arm/boot/dts/bcm4708-netgear-r6250.dts | 3 ++-
arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts | 3 ++-
arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts | 3 ++-
arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts | 3 ++-
arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts | 3 ++-
arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts | 3 ++-
arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts | 3 ++-
arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts | 3 ++-
arch/arm/boot/dts/bcm4709-netgear-r7000.dts | 3 ++-
arch/arm/boot/dts/bcm4709-netgear-r8000.dts | 3 ++-
arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts | 3 ++-
arch/arm/boot/dts/bcm47094-netgear-r8500.dts | 3 ++-
15 files changed, 30 insertions(+), 15 deletions(-)
diff --git a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts b/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts
index 112a5a8..d241cee 100644
--- a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts
+++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts
@@ -21,7 +21,8 @@
};
memory {
- reg = <0x00000000 0x08000000>;
+ reg = <0x00000000 0x08000000
+ 0x88000000 0x08000000>;
};
leds {
diff --git a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts b/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts
index 3600f56..b0e6204 100644
--- a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts
+++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts
@@ -21,7 +21,8 @@
};
memory {
- reg = <0x00000000 0x08000000>;
+ reg = <0x00000000 0x08000000
+ 0x88000000 0x08000000>;
};
leds {
diff --git a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
index d49afec0..c9ba6b9 100644
--- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
+++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
@@ -21,7 +21,8 @@
};
memory {
- reg = <0x00000000 0x08000000>;
+ reg = <0x00000000 0x08000000
+ 0x88000000 0x18000000>;
};
spi {
diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts
index 8519548..b9f66c0 100644
--- a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts
+++ b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts
@@ -21,7 +21,8 @@
};
memory {
- reg = <0x00000000 0x08000000>;
+ reg = <0x00000000 0x08000000
+ 0x88000000 0x08000000>;
};
leds {
diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts b/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts
index 6229ef2..ae0199f 100644
--- a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts
+++ b/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts
@@ -21,7 +21,8 @@
};
memory {
- reg = <0x00000000 0x08000000>;
+ reg = <0x00000000 0x08000000
+ 0x88000000 0x08000000>;
};
leds {
diff --git a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts b/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts
index 74cfcd3..36b628b1 100644
--- a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts
+++ b/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts
@@ -21,7 +21,8 @@
};
memory {
- reg = <0x00000000 0x08000000>;
+ reg = <0x00000000 0x08000000
+ 0x88000000 0x08000000>;
};
leds {
diff --git a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts b/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts
index 71b98cf..db8608b 100644
--- a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts
+++ b/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts
@@ -21,7 +21,8 @@
};
memory {
- reg = <0x00000000 0x08000000>;
+ reg = <0x00000000 0x08000000
+ 0x88000000 0x08000000>;
};
leds {
diff --git a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts b/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts
index 2922536..d51586d 100644
--- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts
+++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts
@@ -21,7 +21,8 @@
};
memory {
- reg = <0x00000000 0x08000000>;
+ reg = <0x00000000 0x08000000
+ 0x88000000 0x08000000>;
};
spi {
diff --git a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts b/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
index 184fd92..de041b8 100644
--- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
+++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
@@ -21,7 +21,8 @@
};
memory {
- reg = <0x00000000 0x08000000>;
+ reg = <0x00000000 0x08000000
+ 0x88000000 0x08000000>;
};
gpio-keys {
diff --git a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
index eac0f52..eaca687 100644
--- a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
+++ b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
@@ -21,7 +21,8 @@
};
memory {
- reg = <0x00000000 0x08000000>;
+ reg = <0x00000000 0x08000000
+ 0x88000000 0x08000000>;
};
leds {
diff --git a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
index aab39c9..b32957c 100644
--- a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
+++ b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
@@ -21,7 +21,8 @@
};
memory {
- reg = <0x00000000 0x08000000>;
+ reg = <0x00000000 0x08000000
+ 0x88000000 0x18000000>;
};
leds {
diff --git a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
index 7ab1176..f459a98 100644
--- a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
+++ b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
@@ -21,7 +21,8 @@
};
memory {
- reg = <0x00000000 0x08000000>;
+ reg = <0x00000000 0x08000000
+ 0x88000000 0x08000000>;
};
leds {
diff --git a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
index 56d38a3..cd13534 100644
--- a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
+++ b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
@@ -21,7 +21,8 @@
};
memory {
- reg = <0x00000000 0x08000000>;
+ reg = <0x00000000 0x08000000
+ 0x88000000 0x08000000>;
};
leds {
diff --git a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
index 7fb9270..64ded76 100644
--- a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
+++ b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
@@ -21,7 +21,8 @@
};
memory {
- reg = <0x00000000 0x08000000>;
+ reg = <0x00000000 0x08000000
+ 0x88000000 0x08000000>;
};
nand: nand@18028000 {
diff --git a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts b/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
index 7ecd57c..600795e 100644
--- a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
+++ b/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
@@ -18,7 +18,8 @@
};
memory {
- reg = <0x00000000 0x08000000>;
+ reg = <0x00000000 0x08000000
+ 0x88000000 0x18000000>;
};
leds {
--
2.10.1
There is one GPIO controlling power for both USB ports.
Signed-off-by: Rafał Miłecki <[email protected]>
Signed-off-by: Rafał Miłecki <[email protected]>
---
arch/arm/boot/dts/bcm4709-netgear-r7000.dts | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
index 0225d82..7ab1176 100644
--- a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
+++ b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
@@ -100,3 +100,11 @@
};
};
};
+
+&usb2 {
+ vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+ vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
+};
--
2.10.1
From: Rafał Miłecki <[email protected]>
Broadcom OHCI and EHCI controllers always have 2 ports each on the root
hub. Describe them in DT to allow specifying extra info or referencing
port nodes.
Signed-off-by: Rafał Miłecki <[email protected]>
---
arch/arm/boot/dts/bcm53573.dtsi | 22 ++++++++++++++++++++++
1 file changed, 22 insertions(+)
diff --git a/arch/arm/boot/dts/bcm53573.dtsi b/arch/arm/boot/dts/bcm53573.dtsi
index e2c496a..2da04d0 100644
--- a/arch/arm/boot/dts/bcm53573.dtsi
+++ b/arch/arm/boot/dts/bcm53573.dtsi
@@ -124,6 +124,17 @@
reg = <0x4000 0x1000>;
interrupt-parent = <&gic>;
interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ehci_port1: port@1 {
+ reg = <1>;
+ };
+
+ ehci_port2: port@2 {
+ reg = <2>;
+ };
};
ohci: ohci@d000 {
@@ -133,6 +144,17 @@
reg = <0xd000 0x1000>;
interrupt-parent = <&gic>;
interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ohci_port1: port@1 {
+ reg = <1>;
+ };
+
+ ohci_port2: port@2 {
+ reg = <2>;
+ };
};
};
--
2.10.1
On 12/6/2016 9:17 AM, Rafał Miłecki wrote:
> From: Rafał Miłecki <[email protected]>
>
> There are 3 separated controllers, one per USB /standard/. With PHY
> drivers in place they can be simply supported with generic drivers.
>
> Signed-off-by: Rafał Miłecki <[email protected]>
> ---
> arch/arm/boot/dts/bcm5301x.dtsi | 33 ++++++++++++++++++++++++++++++++-
> 1 file changed, 32 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
> index f09a2bb..bfc98d19 100644
> --- a/arch/arm/boot/dts/bcm5301x.dtsi
> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
> @@ -248,8 +248,26 @@
>
> #address-cells = <1>;
> #size-cells = <1>;
> + ranges;
>
> - phys = <&usb2_phy>;
> + interrupt-parent = <&gic>;
> +
> + ohci: ohci@21000 {
> + #usb-cells = <0>;
> +
> + compatible = "generic-ohci";
> + reg = <0x00022000 0x1000>;
Your label ohci@21000 does not match the 'reg' at 0x22000.
> + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + ehci: ehci@22000 {
> + #usb-cells = <0>;
> +
> + compatible = "generic-ehci";
> + reg = <0x00021000 0x1000>;
Looks like you got the label of ohci and ehci reversed?
> + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
> + phys = <&usb2_phy>;
> + };
> };
>
> usb3: usb3@23000 {
> @@ -257,6 +275,19 @@
>
> #address-cells = <1>;
> #size-cells = <1>;
> + ranges;
> +
> + interrupt-parent = <&gic>;
> +
> + xhci: xhci@23000 {
> + #usb-cells = <0>;
> +
> + compatible = "generic-xhci";
> + reg = <0x00023000 0x1000>;
> + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
> + phys = <&usb3_phy>;
> + phy-names = "usb";
> + };
> };
>
> spi@29000 {
>
On 6 December 2016 at 18:28, Ray Jui <[email protected]> wrote:
> On 12/6/2016 9:17 AM, Rafał Miłecki wrote:
>> From: Rafał Miłecki <[email protected]>
>>
>> There are 3 separated controllers, one per USB /standard/. With PHY
>> drivers in place they can be simply supported with generic drivers.
>>
>> Signed-off-by: Rafał Miłecki <[email protected]>
>> ---
>> arch/arm/boot/dts/bcm5301x.dtsi | 33 ++++++++++++++++++++++++++++++++-
>> 1 file changed, 32 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
>> index f09a2bb..bfc98d19 100644
>> --- a/arch/arm/boot/dts/bcm5301x.dtsi
>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
>> @@ -248,8 +248,26 @@
>>
>> #address-cells = <1>;
>> #size-cells = <1>;
>> + ranges;
>>
>> - phys = <&usb2_phy>;
>> + interrupt-parent = <&gic>;
>> +
>> + ohci: ohci@21000 {
>> + #usb-cells = <0>;
>> +
>> + compatible = "generic-ohci";
>> + reg = <0x00022000 0x1000>;
>
> Your label ohci@21000 does not match the 'reg' at 0x22000.
>
>> + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
>> + };
>> +
>> + ehci: ehci@22000 {
>> + #usb-cells = <0>;
>> +
>> + compatible = "generic-ehci";
>> + reg = <0x00021000 0x1000>;
>
> Looks like you got the label of ohci and ehci reversed?
Nice catch, thanks! I'll fix it in V2 (just let me wait a day to see
if there will be other comments).
--
Rafał
On 12/6/2016 9:31 AM, Rafał Miłecki wrote:
> On 6 December 2016 at 18:28, Ray Jui <[email protected]> wrote:
>> On 12/6/2016 9:17 AM, Rafał Miłecki wrote:
>>> From: Rafał Miłecki <[email protected]>
>>>
>>> There are 3 separated controllers, one per USB /standard/. With PHY
>>> drivers in place they can be simply supported with generic drivers.
>>>
>>> Signed-off-by: Rafał Miłecki <[email protected]>
>>> ---
>>> arch/arm/boot/dts/bcm5301x.dtsi | 33 ++++++++++++++++++++++++++++++++-
>>> 1 file changed, 32 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
>>> index f09a2bb..bfc98d19 100644
>>> --- a/arch/arm/boot/dts/bcm5301x.dtsi
>>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi
>>> @@ -248,8 +248,26 @@
>>>
>>> #address-cells = <1>;
>>> #size-cells = <1>;
>>> + ranges;
>>>
>>> - phys = <&usb2_phy>;
>>> + interrupt-parent = <&gic>;
>>> +
>>> + ohci: ohci@21000 {
>>> + #usb-cells = <0>;
>>> +
>>> + compatible = "generic-ohci";
>>> + reg = <0x00022000 0x1000>;
>>
>> Your label ohci@21000 does not match the 'reg' at 0x22000.
>>
>>> + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
>>> + };
>>> +
>>> + ehci: ehci@22000 {
>>> + #usb-cells = <0>;
>>> +
>>> + compatible = "generic-ehci";
>>> + reg = <0x00021000 0x1000>;
>>
>> Looks like you got the label of ohci and ehci reversed?
>
> Nice catch, thanks! I'll fix it in V2 (just let me wait a day to see
> if there will be other comments).
>
In V2, please remember to put the nodes in ascending order based on the
base address of the registers, i.e., ehci@21000, and then followed by
ohci@22000.
Thanks,
Ray
On Tue, Dec 06, 2016 at 06:17:12PM +0100, Rafał Miłecki wrote:
> There is one GPIO controlling power for both USB ports.
>
> Signed-off-by: Rafał Miłecki <[email protected]>
> Signed-off-by: Rafał Miłecki <[email protected]>
Was the double Signed-off-by intentional?
> ---
> arch/arm/boot/dts/bcm4709-netgear-r7000.dts | 8 ++++++++
> 1 file changed, 8 insertions(+)
>
> diff --git a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
> index 0225d82..7ab1176 100644
> --- a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
> +++ b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
> @@ -100,3 +100,11 @@
> };
> };
> };
> +
> +&usb2 {
> + vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&usb3 {
> + vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
> +};
> --
> 2.10.1
>
On Tue, Dec 06, 2016 at 06:17:13PM +0100, Rafał Miłecki wrote:
> From: Rafał Miłecki <[email protected]>
>
> So far we were specifying only the first block which is always limited
> up to 128 MiB. There are many devices with 256 MiB and few with 512 MiB.
Assuming that NS is like NSP (and I'm pretty sure it is), there are 2
ways to access the first 128M of RAM, a proxy starting at address 0
and the real address. I think you are splitting RAM by accessing it
both ways, when you really should just be accessing it at the real
address.
Thanks,
Jon
>
> Signed-off-by: Rafał Miłecki <[email protected]>
> ---
> arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts | 3 ++-
> arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts | 3 ++-
> arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts | 3 ++-
> arch/arm/boot/dts/bcm4708-netgear-r6250.dts | 3 ++-
> arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts | 3 ++-
> arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts | 3 ++-
> arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts | 3 ++-
> arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts | 3 ++-
> arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts | 3 ++-
> arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts | 3 ++-
> arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts | 3 ++-
> arch/arm/boot/dts/bcm4709-netgear-r7000.dts | 3 ++-
> arch/arm/boot/dts/bcm4709-netgear-r8000.dts | 3 ++-
> arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts | 3 ++-
> arch/arm/boot/dts/bcm47094-netgear-r8500.dts | 3 ++-
> 15 files changed, 30 insertions(+), 15 deletions(-)
>
> diff --git a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts b/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts
> index 112a5a8..d241cee 100644
> --- a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts
> +++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts
> @@ -21,7 +21,8 @@
> };
>
> memory {
> - reg = <0x00000000 0x08000000>;
> + reg = <0x00000000 0x08000000
> + 0x88000000 0x08000000>;
> };
>
> leds {
> diff --git a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts b/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts
> index 3600f56..b0e6204 100644
> --- a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts
> +++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts
> @@ -21,7 +21,8 @@
> };
>
> memory {
> - reg = <0x00000000 0x08000000>;
> + reg = <0x00000000 0x08000000
> + 0x88000000 0x08000000>;
> };
>
> leds {
> diff --git a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
> index d49afec0..c9ba6b9 100644
> --- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
> +++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
> @@ -21,7 +21,8 @@
> };
>
> memory {
> - reg = <0x00000000 0x08000000>;
> + reg = <0x00000000 0x08000000
> + 0x88000000 0x18000000>;
> };
>
> spi {
> diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts
> index 8519548..b9f66c0 100644
> --- a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts
> +++ b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts
> @@ -21,7 +21,8 @@
> };
>
> memory {
> - reg = <0x00000000 0x08000000>;
> + reg = <0x00000000 0x08000000
> + 0x88000000 0x08000000>;
> };
>
> leds {
> diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts b/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts
> index 6229ef2..ae0199f 100644
> --- a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts
> +++ b/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts
> @@ -21,7 +21,8 @@
> };
>
> memory {
> - reg = <0x00000000 0x08000000>;
> + reg = <0x00000000 0x08000000
> + 0x88000000 0x08000000>;
> };
>
> leds {
> diff --git a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts b/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts
> index 74cfcd3..36b628b1 100644
> --- a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts
> +++ b/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts
> @@ -21,7 +21,8 @@
> };
>
> memory {
> - reg = <0x00000000 0x08000000>;
> + reg = <0x00000000 0x08000000
> + 0x88000000 0x08000000>;
> };
>
> leds {
> diff --git a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts b/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts
> index 71b98cf..db8608b 100644
> --- a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts
> +++ b/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts
> @@ -21,7 +21,8 @@
> };
>
> memory {
> - reg = <0x00000000 0x08000000>;
> + reg = <0x00000000 0x08000000
> + 0x88000000 0x08000000>;
> };
>
> leds {
> diff --git a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts b/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts
> index 2922536..d51586d 100644
> --- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts
> +++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts
> @@ -21,7 +21,8 @@
> };
>
> memory {
> - reg = <0x00000000 0x08000000>;
> + reg = <0x00000000 0x08000000
> + 0x88000000 0x08000000>;
> };
>
> spi {
> diff --git a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts b/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
> index 184fd92..de041b8 100644
> --- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
> +++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
> @@ -21,7 +21,8 @@
> };
>
> memory {
> - reg = <0x00000000 0x08000000>;
> + reg = <0x00000000 0x08000000
> + 0x88000000 0x08000000>;
> };
>
> gpio-keys {
> diff --git a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
> index eac0f52..eaca687 100644
> --- a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
> +++ b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
> @@ -21,7 +21,8 @@
> };
>
> memory {
> - reg = <0x00000000 0x08000000>;
> + reg = <0x00000000 0x08000000
> + 0x88000000 0x08000000>;
> };
>
> leds {
> diff --git a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
> index aab39c9..b32957c 100644
> --- a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
> +++ b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
> @@ -21,7 +21,8 @@
> };
>
> memory {
> - reg = <0x00000000 0x08000000>;
> + reg = <0x00000000 0x08000000
> + 0x88000000 0x18000000>;
> };
>
> leds {
> diff --git a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
> index 7ab1176..f459a98 100644
> --- a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
> +++ b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
> @@ -21,7 +21,8 @@
> };
>
> memory {
> - reg = <0x00000000 0x08000000>;
> + reg = <0x00000000 0x08000000
> + 0x88000000 0x08000000>;
> };
>
> leds {
> diff --git a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
> index 56d38a3..cd13534 100644
> --- a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
> +++ b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
> @@ -21,7 +21,8 @@
> };
>
> memory {
> - reg = <0x00000000 0x08000000>;
> + reg = <0x00000000 0x08000000
> + 0x88000000 0x08000000>;
> };
>
> leds {
> diff --git a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
> index 7fb9270..64ded76 100644
> --- a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
> +++ b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
> @@ -21,7 +21,8 @@
> };
>
> memory {
> - reg = <0x00000000 0x08000000>;
> + reg = <0x00000000 0x08000000
> + 0x88000000 0x08000000>;
> };
>
> nand: nand@18028000 {
> diff --git a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts b/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
> index 7ecd57c..600795e 100644
> --- a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
> +++ b/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
> @@ -18,7 +18,8 @@
> };
>
> memory {
> - reg = <0x00000000 0x08000000>;
> + reg = <0x00000000 0x08000000
> + 0x88000000 0x18000000>;
> };
>
> leds {
> --
> 2.10.1
>
On 6 December 2016 at 21:06, Jon Mason <[email protected]> wrote:
> On Tue, Dec 06, 2016 at 06:17:13PM +0100, Rafał Miłecki wrote:
>> From: Rafał Miłecki <[email protected]>
>>
>> So far we were specifying only the first block which is always limited
>> up to 128 MiB. There are many devices with 256 MiB and few with 512 MiB.
>
> Assuming that NS is like NSP (and I'm pretty sure it is), there are 2
> ways to access the first 128M of RAM, a proxy starting at address 0
> and the real address. I think you are splitting RAM by accessing it
> both ways, when you really should just be accessing it at the real
> address.
I need some more help, please.
This patch (quite well tested) confirms that 0x88000000 can be used to
access RAM at offset 128 MiB. If this is a real address and whole
space is contiguous, it means the base real address should be
0x80000000. So using 0x0 and 0x80000000 should allow accessing
beginning of the RAM. I took a device that was working just fine with:
reg = <0x00000000 0x08000000>;
and I replaced it with:
reg = <0x80000000 0x08000000>;
but it broke things, kernel didn't boot with the last message being:
[ 0.000000] Memory policy: Data cache writealloc
I can see that bcm958525er.dts, bcm958525xmc.dts, bcm958623hr.dts,
bcm958625k.dts bcm988312hr.dts are using 0x60000000 as base address.
It seems to be different from Northstar but I tried following entry
anyway:
reg = <0x60000000 0x08000000>;
and I got kernel hang just like in the previous try.
Did I miss something? Or does Northstar seem to be actually different than NSP?
On Tue, Dec 06, 2016 at 09:57:31PM +0100, Rafał Miłecki wrote:
> On 6 December 2016 at 21:06, Jon Mason <[email protected]> wrote:
> > On Tue, Dec 06, 2016 at 06:17:13PM +0100, Rafał Miłecki wrote:
> >> From: Rafał Miłecki <[email protected]>
> >>
> >> So far we were specifying only the first block which is always limited
> >> up to 128 MiB. There are many devices with 256 MiB and few with 512 MiB.
> >
> > Assuming that NS is like NSP (and I'm pretty sure it is), there are 2
> > ways to access the first 128M of RAM, a proxy starting at address 0
> > and the real address. I think you are splitting RAM by accessing it
> > both ways, when you really should just be accessing it at the real
> > address.
>
> I need some more help, please.
>
> This patch (quite well tested) confirms that 0x88000000 can be used to
> access RAM at offset 128 MiB. If this is a real address and whole
> space is contiguous, it means the base real address should be
> 0x80000000. So using 0x0 and 0x80000000 should allow accessing
> beginning of the RAM. I took a device that was working just fine with:
> reg = <0x00000000 0x08000000>;
> and I replaced it with:
> reg = <0x80000000 0x08000000>;
> but it broke things, kernel didn't boot with the last message being:
> [ 0.000000] Memory policy: Data cache writealloc
>
> I can see that bcm958525er.dts, bcm958525xmc.dts, bcm958623hr.dts,
> bcm958625k.dts bcm988312hr.dts are using 0x60000000 as base address.
> It seems to be different from Northstar but I tried following entry
> anyway:
> reg = <0x60000000 0x08000000>;
> and I got kernel hang just like in the previous try.
>
> Did I miss something? Or does Northstar seem to be actually different than NSP?
Per the BCM5301X Preliminary Programmer's Register Reference guide
(page 394), under the second titled "System Address Mapping".
There is a table listing the System Address Mapping. The parts that
are of interest in this converstation are (and forgive my
approxmiation, but I cannot cut'n'paste from it):
Address Range Size Description
---------------------------------------------------
0x0000_0000-0x07FF_FFFF 128 MB DDR2/3 SDRAM Memory Region*
0x8000_0000-0xBFFF_FFFF 1 G DDR2/3 SDRAM Large Region
* The DDR2/3 SDRAM Memory Region (128MB) is a subset of the DDR2/3
SDRAM Large Region (1GB). Additionally, 0x0000_0000-0x07FF_FFFF is
aliased to 0x8000_0000-0x87FF_FFFF
However, since you say it isn't working for you, then there must be
some other missing peice. I'll retract my comment for now, and
hopefully we can double back and get it working in the future.
Thanks,
Jon