Hello
This patch series add the driver for dwmac-sun8i which handle the Ethernet MAC
present on Allwinner H3/H5/A83T/A64 SoCs.
This driver is the continuation of the sun8i-emac driver.
During the development, it appeared that in fact the hardware was a modified
version of some dwmac.
So the driver is now written as a glue driver for stmmac.
It supports 10/100/1000 Mbit/s speed with half/full duplex.
It can use an internal PHY (MII 10/100) or an external PHY
via RGMII/RMII.
This patch series enable the driver only for the H3/A64/H5 SoC since A83T
doesn't have the necessary clocks present in mainline.
The driver have been tested on the following boards:
- H3 Orange PI PC, BananaPI-M2+
- A64 Pine64, BananaPi-M64
- A83T BananaPI-M3
The first two patchs are some mandatory changes for letting dwmac-sun8i be used.
The following three patchs add the driver and its documentation.
The remaining are DT patch enabling it.
Regards
Corentin Labbe
Changes since v3:
- Renamed tx-delay/rx-delay to tx-delay-ps/rx-delay-ps
- fix syscon compatible example
- Changed parameter type for setup() function
- Dropped some DT patchs for boards which I could not test further
Changes since v2:
- corrected order of syscon compatible
- added compatible = "ethernet-phy-ieee802.3-c22 to PHY
- added set_mac function
Changes since v1:
- added TX/RX delay units
- splitted syscon documentation in its own patch
- regulator is now disabled after clk_prepare_enable(gmac->tx_clk) error
- Fixed a memory leak on mac_device_info
- Use now generic pin config for all DT stuff
- CONFIG_DWMAC_SUN8I is now set to y in defconfigs
Corentin Labbe (18):
net: stmmac: export stmmac_set_mac_addr/stmmac_get_mac_addr
net: stmmac: add optional setup function
dt-bindings: net: Add DT bindings documentation for Allwinner
dwmac-sun8i
dt-bindings: syscon: Add DT bindings documentation for Allwinner
syscon
net: stmmac: Add dwmac-sun8i
arm: sun8i: sunxi-h3-h5: Add dt node for the syscon control module
arm: sun8i: sunxi-h3-h5: add dwmac-sun8i ethernet driver
arm: sun8i: orangepi-pc: Enable dwmac-sun8i
arm: sun8i: orangepi-2: Enable dwmac-sun8i
arm: sun8i: orangepi-one: Enable dwmac-sun8i
arm: sun8i: orangepi-pc-plus: Set EMAC activity LEDs to active high
arm64: allwinner: sun50i-a64: Add dt node for the syscon control
module
arm64: allwinner: sun50i-a64: add dwmac-sun8i Ethernet driver
arm: allwinner: pine64: Enable dwmac-sun8i
arm: allwinner: pine64-plus: Enable dwmac-sun8i
arm64: allwinner: bananapi-m64: Enable dwmac-sun8i
arm: sunxi: Enable dwmac-sun8i driver on sunxi_defconfig
arm: multi_v7: Enable dwmac-sun8i driver on multi_v7_defconfig
.../devicetree/bindings/misc/allwinner,syscon.txt | 19 +
.../devicetree/bindings/net/dwmac-sun8i.txt | 77 ++
arch/arm/boot/dts/sun8i-h3-orangepi-2.dts | 8 +
arch/arm/boot/dts/sun8i-h3-orangepi-one.dts | 8 +
arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts | 5 +
arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts | 8 +
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 40 +
arch/arm/configs/multi_v7_defconfig | 1 +
arch/arm/configs/sunxi_defconfig | 1 +
.../boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 15 +
.../boot/dts/allwinner/sun50i-a64-pine64-plus.dts | 17 +-
.../arm64/boot/dts/allwinner/sun50i-a64-pine64.dts | 16 +
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 43 +
drivers/net/ethernet/stmicro/stmmac/Kconfig | 11 +
drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 960 +++++++++++++++++++++
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c | 3 +-
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 29 +-
.../net/ethernet/stmicro/stmmac/stmmac_platform.c | 9 +-
include/linux/stmmac.h | 2 +
20 files changed, 1268 insertions(+), 5 deletions(-)
create mode 100644 Documentation/devicetree/bindings/misc/allwinner,syscon.txt
create mode 100644 Documentation/devicetree/bindings/net/dwmac-sun8i.txt
create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
--
2.10.2
Thoses symbol will be needed for the dwmac-sun8i ethernet driver.
For letting it to be build as module, they need to be exported.
Signed-off-by: Corentin Labbe <[email protected]>
---
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c b/drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c
index 38f9430..67af0bd 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c
@@ -248,6 +248,7 @@ void stmmac_set_mac_addr(void __iomem *ioaddr, u8 addr[6],
data = (addr[3] << 24) | (addr[2] << 16) | (addr[1] << 8) | addr[0];
writel(data, ioaddr + low);
}
+EXPORT_SYMBOL_GPL(stmmac_set_mac_addr);
/* Enable disable MAC RX/TX */
void stmmac_set_mac(void __iomem *ioaddr, bool enable)
@@ -279,4 +280,4 @@ void stmmac_get_mac_addr(void __iomem *ioaddr, unsigned char *addr,
addr[4] = hi_addr & 0xff;
addr[5] = (hi_addr >> 8) & 0xff;
}
-
+EXPORT_SYMBOL_GPL(stmmac_get_mac_addr);
--
2.10.2
The dwmac-sun8i hardware is present on the pine64
It uses an external PHY via RMII.
Signed-off-by: Corentin Labbe <[email protected]>
---
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
index c680ed3..6aee3d5 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
@@ -109,3 +109,19 @@
&usbphy {
status = "okay";
};
+
+&mdio {
+ ext_rmii_phy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rmii_pins>;
+ phy-mode = "rmii";
+ phy-handle = <&ext_rmii_phy1>;
+ status = "okay";
+
+};
--
2.10.2
This patch add the dt node for the syscon register present on the
Allwinner A64.
Only two register are present in this syscon and the only one useful is
the one dedicated to EMAC clock.
Signed-off-by: Corentin Labbe <[email protected]>
---
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
index c7f669f..0b0f4ab 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -129,6 +129,12 @@
#size-cells = <1>;
ranges;
+ syscon: syscon@01c00000 {
+ compatible = "allwinner,sun8i-a64-system-controller",
+ "syscon";
+ reg = <0x01c00000 0x1000>;
+ };
+
mmc0: mmc@1c0f000 {
compatible = "allwinner,sun50i-a64-mmc";
reg = <0x01c0f000 0x1000>;
--
2.10.2
The dwmac-sun8i hardware is present on the BananaPi M64.
It uses an external PHY rtl8211e via RGMII.
Signed-off-by: Corentin Labbe <[email protected]>
---
arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index 6872135..0c07c89 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -77,6 +77,21 @@
bias-pull-up;
};
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ status = "okay";
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
--
2.10.2
The dwmac-sun8i hardware is present on the pine64 plus.
It uses an external PHY rtl8211e via RGMII.
Signed-off-by: Corentin Labbe <[email protected]>
---
.../arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts | 17 ++++++++++++++++-
1 file changed, 16 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts
index 790d14d..dea76c2 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts
@@ -46,5 +46,20 @@
model = "Pine64+";
compatible = "pine64,pine64-plus", "allwinner,sun50i-a64";
- /* TODO: Camera, Ethernet PHY, touchscreen, etc. */
+ /* TODO: Camera, touchscreen, etc. */
+};
+
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ status = "okay";
};
--
2.10.2
On the Orange Pi PC Plus, the polarity of the LEDs on the RJ45 Ethernet
port were changed from active low to active high.
Signed-off-by: Chen-Yu Tsai <[email protected]>
Signed-off-by: Corentin Labbe <[email protected]>
---
arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts
index 8b93f5c..0380769 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts
@@ -86,3 +86,8 @@
/* eMMC is missing pull-ups */
bias-pull-up;
};
+
+&emac {
+ /* LEDs changed to active high on the plus */
+ /delete-property/ allwinner,leds-active-low;
+};
--
2.10.2
The dwmac-sun8i hardware is present on the Orange PI One.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <[email protected]>
---
arch/arm/boot/dts/sun8i-h3-orangepi-one.dts | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
index 5fea430..2ffa4c1 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
@@ -53,6 +53,7 @@
aliases {
serial0 = &uart0;
+ ethernet0 = &emac;
};
chosen {
@@ -97,6 +98,13 @@
status = "okay";
};
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
--
2.10.2
Enable the dwmac-sun8i driver in the multi_v7 default configuration
Signed-off-by: Corentin Labbe <[email protected]>
---
arch/arm/configs/multi_v7_defconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index 8f6167e..5a553ba 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -257,6 +257,7 @@ CONFIG_SMSC911X=y
CONFIG_STMMAC_ETH=y
CONFIG_STMMAC_PLATFORM=y
CONFIG_DWMAC_DWC_QOS_ETH=y
+CONFIG_DWMAC_SUN8I=y
CONFIG_TI_CPSW=y
CONFIG_XILINX_EMACLITE=y
CONFIG_AT803X_PHY=y
--
2.10.2
Enable the dwmac-sun8i driver in the sunxi default configuration
Signed-off-by: Corentin Labbe <[email protected]>
---
arch/arm/configs/sunxi_defconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/configs/sunxi_defconfig b/arch/arm/configs/sunxi_defconfig
index 5cd5dd70..504e022 100644
--- a/arch/arm/configs/sunxi_defconfig
+++ b/arch/arm/configs/sunxi_defconfig
@@ -40,6 +40,7 @@ CONFIG_ATA=y
CONFIG_AHCI_SUNXI=y
CONFIG_NETDEVICES=y
CONFIG_SUN4I_EMAC=y
+CONFIG_DWMAC_SUN8I=y
# CONFIG_NET_VENDOR_ARC is not set
# CONFIG_NET_CADENCE is not set
# CONFIG_NET_VENDOR_BROADCOM is not set
--
2.10.2
This patch add the dt node for the syscon register present on the
Allwinner H3/H5
Only two register are present in this syscon and the only one useful is
the one dedicated to EMAC clock..
Signed-off-by: Corentin Labbe <[email protected]>
---
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
index 1aeeacb..78d1d61 100644
--- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -83,6 +83,12 @@
#size-cells = <1>;
ranges;
+ syscon: syscon@01c00000 {
+ compatible = "allwinner,sun8i-h3-system-controller",
+ "syscon";
+ reg = <0x01c00000 0x1000>;
+ };
+
dma: dma-controller@01c02000 {
compatible = "allwinner,sun8i-h3-dma";
reg = <0x01c02000 0x1000>;
--
2.10.2
The dwmac-sun8i is an Ethernet MAC that supports 10/100/1000 Mbit
connections. It is very similar to the device found in the Allwinner
H3, but lacks the internal 100 Mbit PHY and its associated control
bits.
This adds the necessary bits to the Allwinner A64 SoC .dtsi, but keeps
it disabled at this level.
Signed-off-by: Corentin Labbe <[email protected]>
---
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 37 +++++++++++++++++++++++++++
1 file changed, 37 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
index 0b0f4ab..2569827 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -287,6 +287,23 @@
bias-pull-up;
};
+ rmii_pins: rmii_pins {
+ pins = "PD10", "PD11", "PD13", "PD14",
+ "PD17", "PD18", "PD19", "PD20",
+ "PD22", "PD23";
+ function = "emac";
+ drive-strength = <40>;
+ };
+
+ rgmii_pins: rgmii_pins {
+ pins = "PD8", "PD9", "PD10", "PD11",
+ "PD12", "PD13", "PD15",
+ "PD16", "PD17", "PD18", "PD19",
+ "PD20", "PD21", "PD22", "PD23";
+ function = "emac";
+ drive-strength = <40>;
+ };
+
uart0_pins_a: uart0@0 {
pins = "PB8", "PB9";
function = "uart0";
@@ -391,6 +408,26 @@
#size-cells = <0>;
};
+ emac: ethernet@1c30000 {
+ compatible = "allwinner,sun50i-a64-emac";
+ syscon = <&syscon>;
+ reg = <0x01c30000 0x100>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu RST_BUS_EMAC>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu CLK_BUS_EMAC>;
+ clock-names = "stmmaceth";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
gic: interrupt-controller@1c81000 {
compatible = "arm,gic-400";
reg = <0x01c81000 0x1000>,
--
2.10.2
The dwmac-sun8i is a heavy hacked version of stmmac hardware by
allwinner.
In fact the only common part is the descriptor management and the first
register function.
Signed-off-by: Corentin Labbe <[email protected]>
---
drivers/net/ethernet/stmicro/stmmac/Kconfig | 11 +
drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 960 +++++++++++++++++++++
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 25 +
.../net/ethernet/stmicro/stmmac/stmmac_platform.c | 9 +-
include/linux/stmmac.h | 1 +
6 files changed, 1005 insertions(+), 2 deletions(-)
create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index cfbe363..85c0e41 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -145,6 +145,17 @@ config DWMAC_SUNXI
This selects Allwinner SoC glue layer support for the
stmmac device driver. This driver is used for A20/A31
GMAC ethernet controller.
+
+config DWMAC_SUN8I
+ tristate "Allwinner sun8i GMAC support"
+ default ARCH_SUNXI
+ depends on OF && (ARCH_SUNXI || COMPILE_TEST)
+ ---help---
+ Support for Allwinner H3 A83T A64 EMAC ethernet controllers.
+
+ This selects Allwinner SoC glue layer support for the
+ stmmac device driver. This driver is used for H3/A83T/A64
+ EMAC ethernet controller.
endif
config STMMAC_PCI
diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
index 700c603..fd4937a 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Makefile
+++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_DWMAC_SOCFPGA) += dwmac-altr-socfpga.o
obj-$(CONFIG_DWMAC_STI) += dwmac-sti.o
obj-$(CONFIG_DWMAC_STM32) += dwmac-stm32.o
obj-$(CONFIG_DWMAC_SUNXI) += dwmac-sunxi.o
+obj-$(CONFIG_DWMAC_SUN8I) += dwmac-sun8i.o
obj-$(CONFIG_DWMAC_DWC_QOS_ETH) += dwmac-dwc-qos-eth.o
obj-$(CONFIG_DWMAC_GENERIC) += dwmac-generic.o
stmmac-platform-objs:= stmmac_platform.o
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
new file mode 100644
index 0000000..0637ca3
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
@@ -0,0 +1,960 @@
+/*
+ * dwmac-sun8i.c - Allwinner sun8i DWMAC specific glue layer
+ *
+ * Copyright (C) 2017 Corentin Labbe <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regmap.h>
+#include <linux/stmmac.h>
+
+#include "stmmac.h"
+#include "stmmac_platform.h"
+
+/* General notes on dwmac-sun8i:
+ * Locking: no locking is necessary in this file because all necessary locking
+ * is done in the "stmmac files"
+ */
+
+/* struct emac_variant - Descrive dwmac-sun8i hardware variant
+ * @default_syscon_value: The default value of the EMAC register in syscon
+ * This value is used for disabling properly EMAC
+ * and used as a good starting value in case of the
+ * boot process(uboot) leave some stuff.
+ * @internal_phy: Does the MAC embed an internal PHY
+ * @support_mii: Does the MAC handle MII
+ * @support_rmii: Does the MAC handle RMII
+ * @support_rgmii: Does the MAC handle RGMII
+ */
+struct emac_variant {
+ u32 default_syscon_value;
+ int internal_phy;
+ bool support_mii;
+ bool support_rmii;
+ bool support_rgmii;
+};
+
+/* struct sunxi_priv_data - hold all sunxi private data
+ * @tx_clk: reference to MAC TX clock
+ * @ephy_clk: reference to the optional EPHY clock for the internal PHY
+ * @regulator: reference to the optional regulator
+ * @rst_ephy: reference to the optional EPHY reset for the internal PHY
+ * @variant: reference to the current board variant
+ * @regmap: regmap for using the syscon
+ * @use_internal_phy: Does the current PHY choice imply using the internal PHY
+ */
+struct sunxi_priv_data {
+ struct clk *tx_clk;
+ struct clk *ephy_clk;
+ struct regulator *regulator;
+ struct reset_control *rst_ephy;
+ const struct emac_variant *variant;
+ struct regmap *regmap;
+ bool use_internal_phy;
+};
+
+static const struct emac_variant emac_variant_h3 = {
+ .default_syscon_value = 0x58000,
+ .internal_phy = PHY_INTERFACE_MODE_MII,
+ .support_mii = true,
+ .support_rmii = true,
+ .support_rgmii = true
+};
+
+static const struct emac_variant emac_variant_a83t = {
+ .default_syscon_value = 0,
+ .internal_phy = 0,
+ .support_mii = true,
+ .support_rgmii = true
+};
+
+static const struct emac_variant emac_variant_a64 = {
+ .default_syscon_value = 0,
+ .internal_phy = 0,
+ .support_mii = true,
+ .support_rmii = true,
+ .support_rgmii = true
+};
+
+#define EMAC_BASIC_CTL0 0x00
+#define EMAC_BASIC_CTL1 0x04
+#define EMAC_INT_STA 0x08
+#define EMAC_INT_EN 0x0C
+#define EMAC_TX_CTL0 0x10
+#define EMAC_TX_CTL1 0x14
+#define EMAC_TX_FLOW_CTL 0x1C
+#define EMAC_TX_DESC_LIST 0x20
+#define EMAC_RX_CTL0 0x24
+#define EMAC_RX_CTL1 0x28
+#define EMAC_RX_DESC_LIST 0x34
+#define EMAC_RX_FRM_FLT 0x38
+#define EMAC_MDIO_CMD 0x48
+#define EMAC_MDIO_DATA 0x4C
+#define EMAC_MACADDR_HI(reg) (0x50 + (reg) * 8)
+#define EMAC_MACADDR_LO(reg) (0x54 + (reg) * 8)
+#define EMAC_TX_DMA_STA 0xB0
+#define EMAC_TX_CUR_DESC 0xB4
+#define EMAC_TX_CUR_BUF 0xB8
+#define EMAC_RX_DMA_STA 0xC0
+#define EMAC_RX_CUR_DESC 0xC4
+#define EMAC_RX_CUR_BUF 0xC8
+
+/* Use in EMAC_BASIC_CTL1 */
+#define EMAC_BURSTLEN_SHIFT 24
+
+/* Used in EMAC_RX_FRM_FLT */
+#define EMAC_FRM_FLT_RXALL BIT(0)
+#define EMAC_FRM_FLT_CTL BIT(13)
+#define EMAC_FRM_FLT_MULTICAST BIT(16)
+
+/* Used in RX_CTL1*/
+#define EMAC_RX_MD BIT(1)
+#define EMAC_RX_TH_MASK GENMASK(4, 5)
+#define EMAC_RX_TH_32 0
+#define EMAC_RX_TH_64 (0x1 << 4)
+#define EMAC_RX_TH_96 (0x2 << 4)
+#define EMAC_RX_TH_128 (0x3 << 4)
+#define EMAC_RX_DMA_EN BIT(30)
+#define EMAC_RX_DMA_START BIT(31)
+
+/* Used in TX_CTL1*/
+#define EMAC_TX_MD BIT(1)
+#define EMAC_TX_NEXT_FRM BIT(2)
+#define EMAC_TX_TH_MASK GENMASK(8, 10)
+#define EMAC_TX_TH_64 0
+#define EMAC_TX_TH_128 (0x1 << 8)
+#define EMAC_TX_TH_192 (0x2 << 8)
+#define EMAC_TX_TH_256 (0x3 << 8)
+#define EMAC_TX_DMA_EN BIT(30)
+#define EMAC_TX_DMA_START BIT(31)
+
+/* Used in RX_CTL0 */
+#define EMAC_RX_RECEIVER_EN BIT(31)
+#define EMAC_RX_DO_CRC BIT(27)
+#define EMAC_RX_FLOW_CTL_EN BIT(16)
+
+/* Used in TX_CTL0 */
+#define EMAC_TX_TRANSMITTER_EN BIT(31)
+
+/* Used in EMAC_TX_FLOW_CTL */
+#define EMAC_TX_FLOW_CTL_EN BIT(0)
+
+/* Used in EMAC_INT_STA */
+#define EMAC_TX_INT BIT(0)
+#define EMAC_TX_DMA_STOP_INT BIT(1)
+#define EMAC_TX_BUF_UA_INT BIT(2)
+#define EMAC_TX_TIMEOUT_INT BIT(3)
+#define EMAC_TX_UNDERFLOW_INT BIT(4)
+#define EMAC_TX_EARLY_INT BIT(5)
+#define EMAC_RX_INT BIT(8)
+#define EMAC_RX_BUF_UA_INT BIT(9)
+#define EMAC_RX_DMA_STOP_INT BIT(10)
+#define EMAC_RX_TIMEOUT_INT BIT(11)
+#define EMAC_RX_OVERFLOW_INT BIT(12)
+#define EMAC_RX_EARLY_INT BIT(13)
+#define EMAC_RGMII_STA_INT BIT(16)
+
+#define MAC_ADDR_TYPE_DST BIT(31)
+
+/* H3 specific bits for EPHY */
+#define H3_EPHY_ADDR_SHIFT 20
+#define H3_EPHY_LED_POL BIT(17) /* 1: active low, 0: active high */
+#define H3_EPHY_SHUTDOWN BIT(16) /* 1: shutdown, 0: power up */
+#define H3_EPHY_SELECT BIT(15) /* 1: internal PHY, 0: external PHY */
+
+/* H3/A64 specific bits */
+#define SYSCON_RMII_EN BIT(13) /* 1: enable RMII (overrides EPIT) */
+
+/* Generic system control EMAC_CLK bits */
+#define SYSCON_ETXDC_MASK GENMASK(2, 0)
+#define SYSCON_ETXDC_SHIFT 10
+#define SYSCON_ERXDC_MASK GENMASK(4, 0)
+#define SYSCON_ERXDC_SHIFT 5
+/* EMAC PHY Interface Type */
+#define SYSCON_EPIT BIT(2) /* 1: RGMII, 0: MII */
+#define SYSCON_ETCS_MASK GENMASK(1, 0)
+#define SYSCON_ETCS_MII 0x0
+#define SYSCON_ETCS_EXT_GMII 0x1
+#define SYSCON_ETCS_INT_GMII 0x2
+#define SYSCON_EMAC_REG 0x30
+
+/* sun8i_dwmac_dma_reset() - reset the EMAC
+ * Called from stmmac via stmmac_dma_ops->reset
+ */
+static int sun8i_dwmac_dma_reset(void __iomem *ioaddr)
+{
+ writel(0, ioaddr + EMAC_RX_CTL1);
+ writel(0, ioaddr + EMAC_TX_CTL1);
+ writel(0, ioaddr + EMAC_RX_FRM_FLT);
+ writel(0, ioaddr + EMAC_RX_DESC_LIST);
+ writel(0, ioaddr + EMAC_TX_DESC_LIST);
+ writel(0, ioaddr + EMAC_INT_EN);
+ writel(0x1FFFFFF, ioaddr + EMAC_INT_STA);
+ return 0;
+}
+
+/* sun8i_dwmac_dma_init() - initialize the EMAC
+ * Called from stmmac via stmmac_dma_ops->init
+ */
+static void sun8i_dwmac_dma_init(void __iomem *ioaddr,
+ struct stmmac_dma_cfg *dma_cfg,
+ u32 dma_tx, u32 dma_rx, int atds)
+{
+ /* Write TX and RX descriptors address */
+ writel(dma_rx, ioaddr + EMAC_RX_DESC_LIST);
+ writel(dma_tx, ioaddr + EMAC_TX_DESC_LIST);
+
+ writel(EMAC_RX_INT | EMAC_TX_INT, ioaddr + EMAC_INT_EN);
+ writel(0x1FFFFFF, ioaddr + EMAC_INT_STA);
+}
+
+/* sun8i_dwmac_dump_regs() - Dump EMAC address space
+ * Called from stmmac_dma_ops->dump_regs
+ * Used for ethtool
+ */
+static void sun8i_dwmac_dump_regs(void __iomem *ioaddr, u32 *reg_space)
+{
+ int i;
+
+ for (i = 0; i < 0xC8; i += 4) {
+ if (i == 0x32 || i == 0x3C)
+ continue;
+ reg_space[i / 4] = readl(ioaddr + i);
+ }
+}
+
+/* sun8i_dwmac_dump_mac_regs() - Dump EMAC address space
+ * Called from stmmac_ops->dump_regs
+ * Used for ethtool
+ */
+static void sun8i_dwmac_dump_mac_regs(struct mac_device_info *hw,
+ u32 *reg_space)
+{
+ int i;
+ void __iomem *ioaddr = hw->pcsr;
+
+ for (i = 0; i < 0xC8; i += 4) {
+ if (i == 0x32 || i == 0x3C)
+ continue;
+ reg_space[i / 4] = readl(ioaddr + i);
+ }
+}
+
+static void sun8i_dwmac_enable_dma_irq(void __iomem *ioaddr, u32 chan)
+{
+ writel(EMAC_RX_INT | EMAC_TX_INT, ioaddr + EMAC_INT_EN);
+}
+
+static void sun8i_dwmac_disable_dma_irq(void __iomem *ioaddr, u32 chan)
+{
+ writel(0, ioaddr + EMAC_INT_EN);
+}
+
+static void sun8i_dwmac_dma_start_tx(void __iomem *ioaddr, u32 chan)
+{
+ u32 v;
+
+ v = readl(ioaddr + EMAC_TX_CTL1);
+ v |= EMAC_TX_DMA_START;
+ v |= EMAC_TX_DMA_EN;
+ writel(v, ioaddr + EMAC_TX_CTL1);
+}
+
+static void sun8i_dwmac_enable_dma_transmission(void __iomem *ioaddr)
+{
+ u32 v;
+
+ v = readl(ioaddr + EMAC_TX_CTL1);
+ v |= EMAC_TX_DMA_START;
+ v |= EMAC_TX_DMA_EN;
+ writel(v, ioaddr + EMAC_TX_CTL1);
+}
+
+static void sun8i_dwmac_dma_stop_tx(void __iomem *ioaddr, u32 chan)
+{
+ u32 v;
+
+ v = readl(ioaddr + EMAC_TX_CTL1);
+ v &= ~EMAC_TX_DMA_EN;
+ writel(v, ioaddr + EMAC_TX_CTL1);
+}
+
+static void sun8i_dwmac_dma_start_rx(void __iomem *ioaddr, u32 chan)
+{
+ u32 v;
+
+ v = readl(ioaddr + EMAC_RX_CTL1);
+ v |= EMAC_RX_DMA_START;
+ v |= EMAC_RX_DMA_EN;
+ writel(v, ioaddr + EMAC_RX_CTL1);
+}
+
+static void sun8i_dwmac_dma_stop_rx(void __iomem *ioaddr, u32 chan)
+{
+ u32 v;
+
+ v = readl(ioaddr + EMAC_RX_CTL1);
+ v &= ~EMAC_RX_DMA_EN;
+ writel(v, ioaddr + EMAC_RX_CTL1);
+}
+
+static int sun8i_dwmac_dma_interrupt(void __iomem *ioaddr,
+ struct stmmac_extra_stats *x, u32 chan)
+{
+ u32 v;
+ int ret = 0;
+
+ v = readl(ioaddr + EMAC_INT_STA);
+
+ if (v & EMAC_TX_INT) {
+ ret |= handle_tx;
+ x->tx_normal_irq_n++;
+ }
+
+ if (v & EMAC_TX_DMA_STOP_INT)
+ x->tx_process_stopped_irq++;
+
+ if (v & EMAC_TX_BUF_UA_INT)
+ x->tx_process_stopped_irq++;
+
+ if (v & EMAC_TX_TIMEOUT_INT)
+ ret |= tx_hard_error;
+
+ if (v & EMAC_TX_UNDERFLOW_INT) {
+ ret |= tx_hard_error;
+ x->tx_undeflow_irq++;
+ }
+
+ if (v & EMAC_TX_EARLY_INT)
+ x->tx_early_irq++;
+
+ if (v & EMAC_RX_INT) {
+ ret |= handle_rx;
+ x->rx_normal_irq_n++;
+ }
+
+ if (v & EMAC_RX_BUF_UA_INT)
+ x->rx_buf_unav_irq++;
+
+ if (v & EMAC_RX_DMA_STOP_INT)
+ x->rx_process_stopped_irq++;
+
+ if (v & EMAC_RX_TIMEOUT_INT)
+ ret |= tx_hard_error;
+
+ if (v & EMAC_RX_OVERFLOW_INT) {
+ ret |= tx_hard_error;
+ x->rx_overflow_irq++;
+ }
+
+ if (v & EMAC_RX_EARLY_INT)
+ x->rx_early_irq++;
+
+ if (v & EMAC_RGMII_STA_INT)
+ x->irq_rgmii_n++;
+
+ writel(v, ioaddr + EMAC_INT_STA);
+
+ return ret;
+}
+
+static void sun8i_dwmac_dma_operation_mode(void __iomem *ioaddr, int txmode,
+ int rxmode, int rxfifosz)
+{
+ u32 v;
+
+ v = readl(ioaddr + EMAC_TX_CTL1);
+ if (txmode == SF_DMA_MODE) {
+ v |= EMAC_TX_MD;
+ /* Undocumented bit (called TX_NEXT_FRM in BSP), the original
+ * comment is
+ * "Operating on second frame increase the performance
+ * especially when transmit store-and-forward is used."
+ */
+ v |= EMAC_TX_NEXT_FRM;
+ } else {
+ v &= ~EMAC_TX_MD;
+ v &= ~EMAC_TX_TH_MASK;
+ if (txmode < 64)
+ v |= EMAC_TX_TH_64;
+ else if (txmode < 128)
+ v |= EMAC_TX_TH_128;
+ else if (txmode < 192)
+ v |= EMAC_TX_TH_192;
+ else if (txmode < 256)
+ v |= EMAC_TX_TH_256;
+ }
+ writel(v, ioaddr + EMAC_TX_CTL1);
+
+ v = readl(ioaddr + EMAC_RX_CTL1);
+ if (rxmode == SF_DMA_MODE) {
+ v |= EMAC_RX_MD;
+ } else {
+ v &= ~EMAC_RX_MD;
+ v &= ~EMAC_RX_TH_MASK;
+ if (rxmode < 32)
+ v |= EMAC_RX_TH_32;
+ else if (rxmode < 64)
+ v |= EMAC_RX_TH_64;
+ else if (rxmode < 96)
+ v |= EMAC_RX_TH_96;
+ else if (rxmode < 128)
+ v |= EMAC_RX_TH_128;
+ }
+ writel(v, ioaddr + EMAC_RX_CTL1);
+}
+
+static const struct stmmac_dma_ops sun8i_dwmac_dma_ops = {
+ .reset = sun8i_dwmac_dma_reset,
+ .init = sun8i_dwmac_dma_init,
+ .dump_regs = sun8i_dwmac_dump_regs,
+ .dma_mode = sun8i_dwmac_dma_operation_mode,
+ .enable_dma_transmission = sun8i_dwmac_enable_dma_transmission,
+ .enable_dma_irq = sun8i_dwmac_enable_dma_irq,
+ .disable_dma_irq = sun8i_dwmac_disable_dma_irq,
+ .start_tx = sun8i_dwmac_dma_start_tx,
+ .stop_tx = sun8i_dwmac_dma_stop_tx,
+ .start_rx = sun8i_dwmac_dma_start_rx,
+ .stop_rx = sun8i_dwmac_dma_stop_rx,
+ .dma_interrupt = sun8i_dwmac_dma_interrupt,
+};
+
+static int sun8i_dwmac_init(struct platform_device *pdev, void *priv)
+{
+ struct sunxi_priv_data *gmac = priv;
+ int ret;
+
+ if (gmac->regulator) {
+ ret = regulator_enable(gmac->regulator);
+ if (ret) {
+ dev_err(&pdev->dev, "Fail to enable regulator\n");
+ return ret;
+ }
+ }
+
+ ret = clk_prepare_enable(gmac->tx_clk);
+ if (ret) {
+ if (gmac->regulator)
+ regulator_disable(gmac->regulator);
+ dev_err(&pdev->dev, "Could not enable AHB clock\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static void sun8i_dwmac_core_init(struct mac_device_info *hw, int mtu)
+{
+ void __iomem *ioaddr = hw->pcsr;
+ u32 v;
+
+ v = (8 << EMAC_BURSTLEN_SHIFT); /* burst len */
+ writel(v, ioaddr + EMAC_BASIC_CTL1);
+}
+
+static void sun8i_dwmac_set_mac(void __iomem *ioaddr, bool enable)
+{
+ u32 t, r;
+
+ t = readl(ioaddr + EMAC_TX_CTL0);
+ r = readl(ioaddr + EMAC_RX_CTL0);
+ if (enable) {
+ t |= EMAC_TX_TRANSMITTER_EN;
+ r |= EMAC_RX_RECEIVER_EN;
+ } else {
+ t &= ~EMAC_TX_TRANSMITTER_EN;
+ r &= ~EMAC_RX_RECEIVER_EN;
+ }
+ writel(t, ioaddr + EMAC_TX_CTL0);
+ writel(r, ioaddr + EMAC_RX_CTL0);
+}
+
+static void sun8i_dwmac_set_umac_addr(struct mac_device_info *hw,
+ unsigned char *addr,
+ unsigned int reg_n)
+{
+ void __iomem *ioaddr = hw->pcsr;
+ u32 v;
+
+ stmmac_set_mac_addr(ioaddr, addr, EMAC_MACADDR_HI(reg_n),
+ EMAC_MACADDR_LO(reg_n));
+ if (reg_n > 0) {
+ v = readl(ioaddr + EMAC_MACADDR_HI(reg_n));
+ v |= MAC_ADDR_TYPE_DST;
+ writel(v, ioaddr + EMAC_MACADDR_HI(reg_n));
+ }
+}
+
+static void sun8i_dwmac_get_umac_addr(struct mac_device_info *hw,
+ unsigned char *addr,
+ unsigned int reg_n)
+{
+ void __iomem *ioaddr = hw->pcsr;
+
+ stmmac_get_mac_addr(ioaddr, addr, EMAC_MACADDR_HI(reg_n),
+ EMAC_MACADDR_LO(reg_n));
+}
+
+/* caution this function must return non 0 to work */
+static int sun8i_dwmac_rx_ipc_enable(struct mac_device_info *hw)
+{
+ void __iomem *ioaddr = hw->pcsr;
+ u32 v;
+
+ v = readl(ioaddr + EMAC_RX_CTL0);
+ v |= EMAC_RX_DO_CRC;
+ writel(v, ioaddr + EMAC_RX_CTL0);
+
+ return 1;
+}
+
+static void sun8i_dwmac_set_filter(struct mac_device_info *hw,
+ struct net_device *dev)
+{
+ void __iomem *ioaddr = hw->pcsr;
+ u32 v;
+ int i = 0;
+ struct netdev_hw_addr *ha;
+
+ v = readl(ioaddr + EMAC_RX_FRM_FLT);
+
+ v |= EMAC_FRM_FLT_CTL;
+
+ if (dev->flags & IFF_PROMISC) {
+ v = EMAC_FRM_FLT_RXALL;
+ } else if (dev->flags & IFF_ALLMULTI) {
+ v = EMAC_FRM_FLT_MULTICAST;
+ } else if (!netdev_mc_empty(dev)) {
+ netdev_for_each_mc_addr(ha, dev) {
+ i++;
+ sun8i_dwmac_set_umac_addr(hw, ha->addr, i);
+ }
+ }
+
+ if (netdev_uc_count(dev) + i > hw->unicast_filter_entries) {
+ netdev_info(dev, "Too many address, switching to promiscuous\n");
+ v = EMAC_FRM_FLT_RXALL;
+ } else {
+ netdev_for_each_uc_addr(ha, dev) {
+ i++;
+ sun8i_dwmac_set_umac_addr(hw, ha->addr, i);
+ }
+ }
+ writel(v, ioaddr + EMAC_RX_FRM_FLT);
+}
+
+static void sun8i_dwmac_flow_ctrl(struct mac_device_info *hw,
+ unsigned int duplex, unsigned int fc,
+ unsigned int pause_time, u32 tx_cnt)
+{
+ void __iomem *ioaddr = hw->pcsr;
+ u32 v;
+
+ v = readl(ioaddr + EMAC_RX_CTL0);
+ if (fc == FLOW_AUTO)
+ v |= EMAC_RX_FLOW_CTL_EN;
+ else
+ v &= ~EMAC_RX_FLOW_CTL_EN;
+ writel(v, ioaddr + EMAC_RX_CTL0);
+
+ v = readl(ioaddr + EMAC_TX_FLOW_CTL);
+ if (fc == FLOW_AUTO)
+ v |= EMAC_TX_FLOW_CTL_EN;
+ else
+ v &= ~EMAC_TX_FLOW_CTL_EN;
+ writel(v, ioaddr + EMAC_TX_FLOW_CTL);
+}
+
+static int sun8i_dwmac_reset(struct stmmac_priv *priv)
+{
+ u32 v;
+ int err;
+
+ v = readl(priv->ioaddr + EMAC_BASIC_CTL1);
+ writel(v | 0x01, priv->ioaddr + EMAC_BASIC_CTL1);
+
+ err = readl_poll_timeout(priv->ioaddr + EMAC_BASIC_CTL1, v,
+ !(v & 0x01), 100, 10000);
+
+ if (err) {
+ dev_err(priv->device, "EMAC reset timeout\n");
+ return -EFAULT;
+ }
+ return 0;
+}
+
+static int sun8i_dwmac_set_syscon(struct stmmac_priv *priv)
+{
+ struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+ struct device_node *node = priv->device->of_node;
+ int ret;
+ u32 reg, val;
+
+ regmap_read(gmac->regmap, SYSCON_EMAC_REG, &val);
+ reg = gmac->variant->default_syscon_value;
+ if (reg != val)
+ dev_warn(priv->device,
+ "Current syscon value is not the default %x (expect %x)\n",
+ val, reg);
+
+ if (gmac->variant->internal_phy) {
+ if (!gmac->use_internal_phy) {
+ /* switch to external PHY interface */
+ reg &= ~H3_EPHY_SELECT;
+ } else {
+ reg |= H3_EPHY_SELECT;
+ reg &= ~H3_EPHY_SHUTDOWN;
+ dev_dbg(priv->device, "Select internal_phy %x\n", reg);
+
+ if (of_property_read_bool(priv->plat->phy_node,
+ "allwinner,leds-active-low"))
+ reg |= H3_EPHY_LED_POL;
+ else
+ reg &= ~H3_EPHY_LED_POL;
+
+ ret = of_mdio_parse_addr(priv->device,
+ priv->plat->phy_node);
+ if (ret < 0) {
+ dev_err(priv->device, "Could not parse MDIO addr\n");
+ return ret;
+ }
+ /* of_mdio_parse_addr returns a valid (0 ~ 31) PHY
+ * address. No need to mask it again.
+ */
+ reg |= ret << H3_EPHY_ADDR_SHIFT;
+ }
+ }
+
+ if (!of_property_read_u32(node, "allwinner,tx-delay-ps", &val)) {
+ if (val % 100) {
+ dev_err(priv->device, "tx-delay must be a multiple of 100\n");
+ return -EINVAL;
+ }
+ val /= 100;
+ dev_dbg(priv->device, "set tx-delay to %x\n", val);
+ if (val <= SYSCON_ETXDC_MASK) {
+ reg &= ~(SYSCON_ETXDC_MASK << SYSCON_ETXDC_SHIFT);
+ reg |= (val << SYSCON_ETXDC_SHIFT);
+ } else {
+ dev_err(priv->device, "Invalid TX clock delay: %d\n",
+ val);
+ return -EINVAL;
+ }
+ }
+
+ if (!of_property_read_u32(node, "allwinner,rx-delay-ps", &val)) {
+ if (val % 100) {
+ dev_err(priv->device, "rx-delay must be a multiple of 100\n");
+ return -EINVAL;
+ }
+ val /= 100;
+ dev_dbg(priv->device, "set rx-delay to %x\n", val);
+ if (val <= SYSCON_ERXDC_MASK) {
+ reg &= ~(SYSCON_ERXDC_MASK << SYSCON_ERXDC_SHIFT);
+ reg |= (val << SYSCON_ERXDC_SHIFT);
+ } else {
+ dev_err(priv->device, "Invalid RX clock delay: %d\n",
+ val);
+ return -EINVAL;
+ }
+ }
+
+ /* Clear interface mode bits */
+ reg &= ~(SYSCON_ETCS_MASK | SYSCON_EPIT);
+ if (gmac->variant->support_rmii)
+ reg &= ~SYSCON_RMII_EN;
+
+ switch (priv->plat->interface) {
+ case PHY_INTERFACE_MODE_MII:
+ /* default */
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ reg |= SYSCON_EPIT | SYSCON_ETCS_INT_GMII;
+ break;
+ case PHY_INTERFACE_MODE_RMII:
+ reg |= SYSCON_RMII_EN | SYSCON_ETCS_EXT_GMII;
+ break;
+ default:
+ dev_err(priv->device, "Unsupported interface mode: %s",
+ phy_modes(priv->plat->interface));
+ return -EINVAL;
+ }
+
+ regmap_write(gmac->regmap, SYSCON_EMAC_REG, reg);
+
+ return 0;
+}
+
+static void sun8i_dwmac_unset_syscon(struct sunxi_priv_data *gmac)
+{
+ u32 reg = gmac->variant->default_syscon_value;
+
+ regmap_write(gmac->regmap, SYSCON_EMAC_REG, reg);
+}
+
+static int sun8i_dwmac_power_internal_phy(struct stmmac_priv *priv)
+{
+ struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+ int ret;
+
+ if (gmac->ephy_clk) {
+ ret = clk_prepare_enable(gmac->ephy_clk);
+ if (ret) {
+ dev_err(priv->device, "Cannot enable ephy\n");
+ return ret;
+ }
+ }
+
+ if (gmac->rst_ephy) {
+ ret = reset_control_deassert(gmac->rst_ephy);
+ if (ret) {
+ dev_err(priv->device, "Cannot deassert ephy\n");
+ clk_disable_unprepare(gmac->ephy_clk);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static int sun8i_dwmac_unpower_internal_phy(struct sunxi_priv_data *gmac)
+{
+ if (gmac->ephy_clk)
+ clk_disable_unprepare(gmac->ephy_clk);
+ if (gmac->rst_ephy)
+ reset_control_assert(gmac->rst_ephy);
+ return 0;
+}
+
+static int sun8i_power_phy(struct stmmac_priv *priv)
+{
+ struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+ int ret;
+
+ ret = sun8i_dwmac_power_internal_phy(priv);
+ if (ret)
+ return ret;
+
+ ret = sun8i_dwmac_set_syscon(priv);
+ if (ret)
+ goto error_phy;
+
+ ret = sun8i_dwmac_reset(priv);
+ if (ret)
+ goto error_phy;
+ return 0;
+
+error_phy:
+ sun8i_dwmac_unset_syscon(gmac);
+ sun8i_dwmac_unpower_internal_phy(gmac);
+ return ret;
+}
+
+static void sun8i_unpower_phy(struct sunxi_priv_data *gmac)
+{
+ sun8i_dwmac_unset_syscon(gmac);
+ sun8i_dwmac_unpower_internal_phy(gmac);
+}
+
+static void sun8i_dwmac_exit(struct platform_device *pdev, void *priv)
+{
+ struct sunxi_priv_data *gmac = priv;
+
+ sun8i_unpower_phy(gmac);
+
+ clk_disable_unprepare(gmac->tx_clk);
+
+ if (gmac->regulator)
+ regulator_disable(gmac->regulator);
+}
+
+static const struct stmmac_ops sun8i_dwmac_ops = {
+ .core_init = sun8i_dwmac_core_init,
+ .set_mac = sun8i_dwmac_set_mac,
+ .dump_regs = sun8i_dwmac_dump_mac_regs,
+ .rx_ipc = sun8i_dwmac_rx_ipc_enable,
+ .set_filter = sun8i_dwmac_set_filter,
+ .flow_ctrl = sun8i_dwmac_flow_ctrl,
+ .set_umac_addr = sun8i_dwmac_set_umac_addr,
+ .get_umac_addr = sun8i_dwmac_get_umac_addr,
+};
+
+static struct mac_device_info *sun8i_dwmac_setup(void *ppriv)
+{
+ struct mac_device_info *mac;
+ struct stmmac_priv *priv = ppriv;
+ int ret;
+
+ mac = devm_kzalloc(priv->device, sizeof(*mac), GFP_KERNEL);
+ if (!mac)
+ return NULL;
+
+ ret = sun8i_power_phy(priv);
+ if (ret)
+ return NULL;
+
+ mac->pcsr = priv->ioaddr;
+ mac->mac = &sun8i_dwmac_ops;
+ mac->dma = &sun8i_dwmac_dma_ops;
+
+ mac->link.port = 0;
+ mac->link.duplex = BIT(0);
+ mac->link.speed = 1;
+ mac->mii.addr = EMAC_MDIO_CMD;
+ mac->mii.data = EMAC_MDIO_DATA;
+ mac->mii.reg_shift = 4;
+ mac->mii.reg_mask = GENMASK(8, 4);
+ mac->mii.addr_shift = 12;
+ mac->mii.addr_mask = GENMASK(16, 12);
+ mac->mii.clk_csr_shift = 20;
+ mac->mii.clk_csr_mask = GENMASK(22, 20);
+ mac->unicast_filter_entries = 8;
+
+ /* Synopsys Id is not available */
+ priv->synopsys_id = 0;
+
+ return mac;
+}
+
+static int sun8i_dwmac_probe(struct platform_device *pdev)
+{
+ struct plat_stmmacenet_data *plat_dat;
+ struct stmmac_resources stmmac_res;
+ struct sunxi_priv_data *gmac;
+ struct device *dev = &pdev->dev;
+ int ret;
+
+ ret = stmmac_get_platform_resources(pdev, &stmmac_res);
+ if (ret)
+ return ret;
+
+ plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac);
+ if (IS_ERR(plat_dat))
+ return PTR_ERR(plat_dat);
+
+ gmac = devm_kzalloc(dev, sizeof(*gmac), GFP_KERNEL);
+ if (!gmac)
+ return -ENOMEM;
+
+ gmac->variant = of_device_get_match_data(&pdev->dev);
+ if (!gmac->variant) {
+ dev_err(&pdev->dev, "Missing sun8i-emac variant\n");
+ return -EINVAL;
+ }
+
+ gmac->tx_clk = devm_clk_get(dev, "stmmaceth");
+ if (IS_ERR(gmac->tx_clk)) {
+ dev_err(dev, "could not get tx clock\n");
+ return PTR_ERR(gmac->tx_clk);
+ }
+
+ /* Optional regulator for PHY */
+ gmac->regulator = devm_regulator_get_optional(dev, "phy");
+ if (IS_ERR(gmac->regulator)) {
+ if (PTR_ERR(gmac->regulator) == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+ dev_info(dev, "no regulator found\n");
+ gmac->regulator = NULL;
+ }
+
+ gmac->regmap = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+ "syscon");
+ if (IS_ERR(gmac->regmap)) {
+ ret = PTR_ERR(gmac->regmap);
+ dev_err(&pdev->dev, "unable to map SYSCON:%d\n", ret);
+ return ret;
+ }
+
+ plat_dat->interface = of_get_phy_mode(dev->of_node);
+ if (plat_dat->interface == gmac->variant->internal_phy) {
+ dev_info(&pdev->dev, "Will use internal PHY\n");
+ gmac->use_internal_phy = true;
+ gmac->ephy_clk = of_clk_get(plat_dat->phy_node, 0);
+ if (IS_ERR(gmac->ephy_clk)) {
+ ret = PTR_ERR(gmac->ephy_clk);
+ dev_err(&pdev->dev, "Cannot get EPHY clock err=%d\n",
+ ret);
+ return -EINVAL;
+ }
+
+ gmac->rst_ephy = of_reset_control_get(plat_dat->phy_node, NULL);
+ if (IS_ERR(gmac->rst_ephy)) {
+ ret = PTR_ERR(gmac->rst_ephy);
+ if (ret == -EPROBE_DEFER)
+ return ret;
+ dev_err(&pdev->dev, "No EPHY reset control found %d\n",
+ ret);
+ return -EINVAL;
+ }
+ } else {
+ dev_info(&pdev->dev, "Will use external PHY\n");
+ gmac->use_internal_phy = false;
+ }
+
+ /* platform data specifying hardware features and callbacks.
+ * hardware features were copied from Allwinner drivers.
+ */
+ plat_dat->rx_coe = STMMAC_RX_COE_TYPE2;
+ plat_dat->tx_coe = 1;
+ plat_dat->has_sun8i = true;
+ plat_dat->bsp_priv = gmac;
+ plat_dat->init = sun8i_dwmac_init;
+ plat_dat->exit = sun8i_dwmac_exit;
+ plat_dat->setup = sun8i_dwmac_setup;
+
+ ret = sun8i_dwmac_init(pdev, plat_dat->bsp_priv);
+ if (ret)
+ return ret;
+
+ ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
+ if (ret)
+ sun8i_dwmac_exit(pdev, plat_dat->bsp_priv);
+
+ return ret;
+}
+
+static const struct of_device_id sun8i_dwmac_match[] = {
+ { .compatible = "allwinner,sun8i-h3-emac",
+ .data = &emac_variant_h3 },
+ { .compatible = "allwinner,sun8i-a83t-emac",
+ .data = &emac_variant_a83t },
+ { .compatible = "allwinner,sun50i-a64-emac",
+ .data = &emac_variant_a64 },
+ { }
+};
+MODULE_DEVICE_TABLE(of, sun8i_dwmac_match);
+
+static struct platform_driver sun8i_dwmac_driver = {
+ .probe = sun8i_dwmac_probe,
+ .remove = stmmac_pltfr_remove,
+ .driver = {
+ .name = "sun8i-dwmac",
+ .pm = &stmmac_pltfr_pm_ops,
+ .of_match_table = sun8i_dwmac_match,
+ },
+};
+module_platform_driver(sun8i_dwmac_driver);
+
+MODULE_AUTHOR("Corentin Labbe <[email protected]>");
+MODULE_DESCRIPTION("Allwinner sun8i DWMAC specific glue layer");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 72d371d..f9301f0 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -235,6 +235,17 @@ static void stmmac_clk_csr_set(struct stmmac_priv *priv)
else if ((clk_rate >= CSR_F_250M) && (clk_rate < CSR_F_300M))
priv->clk_csr = STMMAC_CSR_250_300M;
}
+
+ if (priv->plat->has_sun8i) {
+ if (clk_rate > 160000000)
+ priv->clk_csr = 0x03;
+ else if (clk_rate > 80000000)
+ priv->clk_csr = 0x02;
+ else if (clk_rate > 40000000)
+ priv->clk_csr = 0x01;
+ else
+ priv->clk_csr = 0;
+ }
}
static void print_pkt(unsigned char *buf, int len)
@@ -784,6 +795,10 @@ static void stmmac_adjust_link(struct net_device *dev)
if (phydev->link) {
u32 ctrl = readl(priv->ioaddr + MAC_CTRL_REG);
+ /* disable loopback */
+ if (priv->plat->has_sun8i)
+ ctrl &= ~BIT(1);
+
/* Now we make sure that we can be in full duplex mode.
* If not, we operate in half-duplex mode. */
if (phydev->duplex != priv->oldduplex) {
@@ -800,6 +815,8 @@ static void stmmac_adjust_link(struct net_device *dev)
if (phydev->speed != priv->speed) {
new_state = 1;
+ if (priv->plat->has_sun8i)
+ ctrl &= ~GENMASK(3, 2);
switch (phydev->speed) {
case 1000:
if (priv->plat->has_gmac ||
@@ -811,6 +828,8 @@ static void stmmac_adjust_link(struct net_device *dev)
priv->plat->has_gmac4) {
ctrl |= priv->hw->link.port;
ctrl |= priv->hw->link.speed;
+ } else if (priv->plat->has_sun8i) {
+ ctrl |= 3 << 2;
} else {
ctrl &= ~priv->hw->link.port;
}
@@ -820,6 +839,8 @@ static void stmmac_adjust_link(struct net_device *dev)
priv->plat->has_gmac4) {
ctrl |= priv->hw->link.port;
ctrl &= ~(priv->hw->link.speed);
+ } else if (priv->plat->has_sun8i) {
+ ctrl |= 2 << 2;
} else {
ctrl &= ~priv->hw->link.port;
}
@@ -3968,6 +3989,10 @@ static int stmmac_hw_init(struct stmmac_priv *priv)
priv->hw = mac;
+ /* dwmac-sun8i only work in chain mode */
+ if (priv->plat->has_sun8i)
+ chain_mode = 1;
+
/* To use the chained or ring mode */
if (priv->synopsys_id >= DWMAC_CORE_4_00) {
priv->hw->mode = &dwmac4_ring_mode_ops;
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index 7fc3a1e..3840529 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -309,6 +309,12 @@ static int stmmac_dt_phy(struct plat_stmmacenet_data *plat,
struct device_node *np, struct device *dev)
{
bool mdio = true;
+ static const struct of_device_id need_mdio_ids[] = {
+ { .compatible = "snps,dwc-qos-ethernet-4.10" },
+ { .compatible = "allwinner,sun8i-a83t-emac" },
+ { .compatible = "allwinner,sun8i-h3-emac" },
+ { .compatible = "allwinner,sun50i-a64-emac" },
+ };
/* If phy-handle property is passed from DT, use it as the PHY */
plat->phy_node = of_parse_phandle(np, "phy-handle", 0);
@@ -325,8 +331,7 @@ static int stmmac_dt_phy(struct plat_stmmacenet_data *plat,
mdio = false;
}
- /* exception for dwmac-dwc-qos-eth glue logic */
- if (of_device_is_compatible(np, "snps,dwc-qos-ethernet-4.10")) {
+ if (of_match_node(need_mdio_ids, np)) {
plat->mdio_node = of_get_child_by_name(np, "mdio");
} else {
/**
diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
index 8bb550b..108739f 100644
--- a/include/linux/stmmac.h
+++ b/include/linux/stmmac.h
@@ -186,6 +186,7 @@ struct plat_stmmacenet_data {
struct reset_control *stmmac_rst;
struct stmmac_axi *axi;
int has_gmac4;
+ bool has_sun8i;
bool tso_en;
int mac_port_sel_speed;
bool en_tx_lpi_clockgating;
--
2.10.2
The dwmac-sun8i is an ethernet MAC hardware that support 10/100/1000
speed.
This patch enable the dwmac-sun8i on Allwinner H3/H5 SoC Device-tree.
SoC H3/H5 have an internal PHY, so optionals syscon and ephy are set.
Signed-off-by: Corentin Labbe <[email protected]>
---
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 34 ++++++++++++++++++++++++++++++++++
1 file changed, 34 insertions(+)
diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
index 78d1d61..34ec227 100644
--- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -285,6 +285,14 @@
interrupt-controller;
#interrupt-cells = <3>;
+ emac_rgmii_pins: emac0@0 {
+ pins = "PD0", "PD1", "PD2", "PD3", "PD4",
+ "PD5", "PD7", "PD8", "PD9", "PD10",
+ "PD12", "PD13", "PD15", "PD16", "PD17";
+ function = "emac";
+ drive-strength = <40>;
+ };
+
i2c0_pins: i2c0 {
pins = "PA11", "PA12";
function = "i2c0";
@@ -381,6 +389,32 @@
clocks = <&osc24M>;
};
+ emac: ethernet@1c30000 {
+ compatible = "allwinner,sun8i-h3-emac";
+ syscon = <&syscon>;
+ reg = <0x01c30000 0x104>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu RST_BUS_EMAC>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu CLK_BUS_EMAC>;
+ clock-names = "stmmaceth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ int_mii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ clocks = <&ccu CLK_BUS_EPHY>;
+ resets = <&ccu RST_BUS_EPHY>;
+ };
+ };
+ };
+
spi0: spi@01c68000 {
compatible = "allwinner,sun8i-h3-spi";
reg = <0x01c68000 0x1000>;
--
2.10.2
The dwmac-sun8i hardware is present on the Orange PI 2.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <[email protected]>
---
arch/arm/boot/dts/sun8i-h3-orangepi-2.dts | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
index 5b6d145..3f54b12 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
@@ -55,6 +55,7 @@
serial0 = &uart0;
/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
ethernet1 = &rtl8189;
+ ethernet0 = &emac;
};
chosen {
@@ -203,3 +204,10 @@
usb1_vbus-supply = <®_usb1_vbus>;
status = "okay";
};
+
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
--
2.10.2
The dwmac-sun8i hardware is present on the Orange PI PC.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <[email protected]>
---
arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
index f148111..746c25a 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
@@ -53,6 +53,7 @@
aliases {
serial0 = &uart0;
+ ethernet0 = &emac;
};
chosen {
@@ -184,3 +185,10 @@
/* USB VBUS is always on */
status = "okay";
};
+
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
--
2.10.2
This patch adds documentation for Device-Tree bindings for the
syscon present in allwinner devices.
Signed-off-by: Corentin Labbe <[email protected]>
---
.../devicetree/bindings/misc/allwinner,syscon.txt | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
create mode 100644 Documentation/devicetree/bindings/misc/allwinner,syscon.txt
diff --git a/Documentation/devicetree/bindings/misc/allwinner,syscon.txt b/Documentation/devicetree/bindings/misc/allwinner,syscon.txt
new file mode 100644
index 0000000..c056c5b
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/allwinner,syscon.txt
@@ -0,0 +1,19 @@
+* Allwinner sun8i system controller
+
+This file describes the bindings for the system controller present in
+Allwinner SoC H3, A83T and A64.
+The principal function of this syscon is to control EMAC PHY choice and
+config.
+
+Required properties for the system controller:
+- reg: address and length of the register for the device.
+- compatible: should be "syscon" and one of the following string:
+ "allwinner,sun8i-h3-system-controller"
+ "allwinner,sun8i-a64-system-controller"
+ "allwinner,sun8i-a83t-system-controller"
+
+Example:
+syscon: syscon@01c00000 {
+ compatible = "allwinner,sun8i-h3-system-controller", "syscon";
+ reg = <0x01c00000 0x1000>;
+};
--
2.10.2
This patch adds documentation for Device-Tree bindings for the
Allwinner dwmac-sun8i driver.
Signed-off-by: Corentin Labbe <[email protected]>
Acked-by: Rob Herring <[email protected]>
---
.../devicetree/bindings/net/dwmac-sun8i.txt | 77 ++++++++++++++++++++++
1 file changed, 77 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/dwmac-sun8i.txt
diff --git a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt
new file mode 100644
index 0000000..a0dca0c
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt
@@ -0,0 +1,77 @@
+* Allwinner sun8i GMAC ethernet controller
+
+This device is a platform glue layer for stmmac.
+Please see stmmac.txt for the other unchanged properties.
+
+Required properties:
+- compatible: should be one of the following string:
+ "allwinner,sun8i-a83t-emac"
+ "allwinner,sun8i-h3-emac"
+ "allwinner,sun50i-a64-emac"
+- reg: address and length of the register for the device.
+- interrupts: interrupt for the device
+- interrupt-names: should be "macirq"
+- clocks: A phandle to the reference clock for this device
+- clock-names: should be "stmmaceth"
+- resets: A phandle to the reset control for this device
+- reset-names: should be "stmmaceth"
+- phy-mode: See ethernet.txt
+- phy-handle: See ethernet.txt
+- #address-cells: shall be 1
+- #size-cells: shall be 0
+- syscon: A phandle to the syscon of the SoC with one of the following
+ compatible string:
+ - allwinner,sun8i-h3-system-controller
+ - allwinner,sun8i-a64-system-controller
+ - allwinner,sun8i-a83t-system-controller
+
+Optional properties:
+- allwinner,tx-delay-ps: TX clock delay chain value in ps. Range value is 0-700. Default is 0)
+- allwinner,rx-delay-ps: RX clock delay chain value in ps. Range value is 0-3100. Default is 0)
+Both delay properties need to be a multiple of 100.
+
+Optional properties for "allwinner,sun8i-h3-emac":
+- allwinner,leds-active-low: EPHY LEDs are active low
+
+Required child node of emac:
+- mdio bus node: should be named mdio
+
+Required properties of the mdio node:
+- #address-cells: shall be 1
+- #size-cells: shall be 0
+
+The device node referenced by "phy" or "phy-handle" should be a child node
+of the mdio node. See phy.txt for the generic PHY bindings.
+
+Required properties of the phy node with "allwinner,sun8i-h3-emac":
+- clocks: a phandle to the reference clock for the EPHY
+- resets: a phandle to the reset control for the EPHY
+
+Example:
+
+emac: ethernet@1c0b000 {
+ compatible = "allwinner,sun8i-h3-emac";
+ syscon = <&syscon>;
+ reg = <0x01c0b000 0x104>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu RST_BUS_EMAC>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu CLK_BUS_EMAC>;
+ clock-names = "stmmaceth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ int_mii_phy: ethernet-phy@1 {
+ reg = <1>;
+ clocks = <&ccu CLK_BUS_EPHY>;
+ resets = <&ccu RST_BUS_EPHY>;
+ };
+ };
+};
--
2.10.2
Instead of adding more ifthen logic for adding a new mac_device_info
setup function, it is easier to add a function pointer to the function
needed.
Signed-off-by: Corentin Labbe <[email protected]>
---
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 4 +++-
include/linux/stmmac.h | 1 +
2 files changed, 4 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index a89f76b..72d371d 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -3946,7 +3946,9 @@ static int stmmac_hw_init(struct stmmac_priv *priv)
struct mac_device_info *mac;
/* Identify the MAC HW device */
- if (priv->plat->has_gmac) {
+ if (priv->plat->setup) {
+ mac = priv->plat->setup(priv);
+ } else if (priv->plat->has_gmac) {
priv->dev->priv_flags |= IFF_UNICAST_FLT;
mac = dwmac1000_setup(priv->ioaddr,
priv->plat->multicast_filter_bins,
diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
index 3921cb9..8bb550b 100644
--- a/include/linux/stmmac.h
+++ b/include/linux/stmmac.h
@@ -177,6 +177,7 @@ struct plat_stmmacenet_data {
void (*fix_mac_speed)(void *priv, unsigned int speed);
int (*init)(struct platform_device *pdev, void *priv);
void (*exit)(struct platform_device *pdev, void *priv);
+ struct mac_device_info *(*setup)(void *priv);
void *bsp_priv;
struct clk *stmmac_clk;
struct clk *pclk;
--
2.10.2
Hi Corentin,
On Wed, Apr 12, 2017 at 01:13:50PM +0200, Corentin Labbe wrote:
> The dwmac-sun8i hardware is present on the Orange PI PC.
> It uses the internal PHY.
>
> This patch create the needed emac node.
>
> Signed-off-by: Corentin Labbe <[email protected]>
> ---
> arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts | 8 ++++++++
> 1 file changed, 8 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
> index f148111..746c25a 100644
> --- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
> +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
> @@ -53,6 +53,7 @@
>
> aliases {
> serial0 = &uart0;
> + ethernet0 = &emac;
Sorry for not spotting this earlier...
This should be ordered by alphabetical order,
> };
>
> chosen {
> @@ -184,3 +185,10 @@
> /* USB VBUS is always on */
> status = "okay";
> };
> +
> +&emac {
> + phy-handle = <&int_mii_phy>;
> + phy-mode = "mii";
> + allwinner,leds-active-low;
> + status = "okay";
> +};
And the node here as well.
Almost all your other DT patches also have this issue, please fix it
in all of them.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
On Wed, Apr 12, 2017 at 01:13:55PM +0200, Corentin Labbe wrote:
> The dwmac-sun8i is an Ethernet MAC that supports 10/100/1000 Mbit
> connections. It is very similar to the device found in the Allwinner
> H3, but lacks the internal 100 Mbit PHY and its associated control
> bits.
> This adds the necessary bits to the Allwinner A64 SoC .dtsi, but keeps
> it disabled at this level.
>
> Signed-off-by: Corentin Labbe <[email protected]>
> ---
> arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 37 +++++++++++++++++++++++++++
> 1 file changed, 37 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> index 0b0f4ab..2569827 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> @@ -287,6 +287,23 @@
> bias-pull-up;
> };
>
> + rmii_pins: rmii_pins {
> + pins = "PD10", "PD11", "PD13", "PD14",
> + "PD17", "PD18", "PD19", "PD20",
> + "PD22", "PD23";
Please align the wrapped lines on the first pin.
> + function = "emac";
> + drive-strength = <40>;
Do you actually need that for all the boards, or only a few of them?
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
On Wed, Apr 12, 2017 at 01:13:56PM +0200, Corentin Labbe wrote:
> The dwmac-sun8i hardware is present on the pine64
> It uses an external PHY via RMII.
>
> Signed-off-by: Corentin Labbe <[email protected]>
The architecture in your commit title in arm64, not arm (the next
patch also have this issue).
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
On Wed, Apr 12, 2017 at 01:14:00PM +0200, Corentin Labbe wrote:
> Enable the dwmac-sun8i driver in the multi_v7 default configuration
>
> Signed-off-by: Corentin Labbe <[email protected]>
Maybe we should enable that in arm64's defconfig too?
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
On Wed, Apr 12, 2017 at 01:13:46PM +0200, Corentin Labbe wrote:
> This patch adds documentation for Device-Tree bindings for the
> syscon present in allwinner devices.
>
> Signed-off-by: Corentin Labbe <[email protected]>
> ---
> .../devicetree/bindings/misc/allwinner,syscon.txt | 19 +++++++++++++++++++
> 1 file changed, 19 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/misc/allwinner,syscon.txt
Acked-by: Rob Herring <[email protected]>
On 12/04/17 12:13, Corentin Labbe wrote:
> This patch adds documentation for Device-Tree bindings for the
> syscon present in allwinner devices.
>
> Signed-off-by: Corentin Labbe <[email protected]>
> ---
> .../devicetree/bindings/misc/allwinner,syscon.txt | 19 +++++++++++++++++++
> 1 file changed, 19 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/misc/allwinner,syscon.txt
>
> diff --git a/Documentation/devicetree/bindings/misc/allwinner,syscon.txt b/Documentation/devicetree/bindings/misc/allwinner,syscon.txt
> new file mode 100644
> index 0000000..c056c5b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/misc/allwinner,syscon.txt
> @@ -0,0 +1,19 @@
> +* Allwinner sun8i system controller
> +
> +This file describes the bindings for the system controller present in
> +Allwinner SoC H3, A83T and A64.
> +The principal function of this syscon is to control EMAC PHY choice and
> +config.
> +
> +Required properties for the system controller:
> +- reg: address and length of the register for the device.
> +- compatible: should be "syscon" and one of the following string:
> + "allwinner,sun8i-h3-system-controller"
> + "allwinner,sun8i-a64-system-controller"
While sun8i might make some sense technically, all 64-bit sunxi
compatible strings use the sun50i prefix to follow the Allwinner naming.
So this should read:
"allwinner,sun50i-a64-system-controller"
Also I am wondering if we should add a compatible string for the H5
(support for that SoC is in -next already):
"allwinner,sun50i-h5-system-controller"
Cheers,
Andre.
> + "allwinner,sun8i-a83t-system-controller"
> +
> +Example:
> +syscon: syscon@01c00000 {
> + compatible = "allwinner,sun8i-h3-system-controller", "syscon";
> + reg = <0x01c00000 0x1000>;
> +};
>
On Thu, Apr 20, 2017 at 12:38:50AM +0100, Andr? Przywara wrote:
> On 12/04/17 12:13, Corentin Labbe wrote:
> > This patch adds documentation for Device-Tree bindings for the
> > syscon present in allwinner devices.
> >
> > Signed-off-by: Corentin Labbe <[email protected]>
> > ---
> > .../devicetree/bindings/misc/allwinner,syscon.txt | 19 +++++++++++++++++++
> > 1 file changed, 19 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/misc/allwinner,syscon.txt
> >
> > diff --git a/Documentation/devicetree/bindings/misc/allwinner,syscon.txt b/Documentation/devicetree/bindings/misc/allwinner,syscon.txt
> > new file mode 100644
> > index 0000000..c056c5b
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/misc/allwinner,syscon.txt
> > @@ -0,0 +1,19 @@
> > +* Allwinner sun8i system controller
> > +
> > +This file describes the bindings for the system controller present in
> > +Allwinner SoC H3, A83T and A64.
> > +The principal function of this syscon is to control EMAC PHY choice and
> > +config.
> > +
> > +Required properties for the system controller:
> > +- reg: address and length of the register for the device.
> > +- compatible: should be "syscon" and one of the following string:
> > + "allwinner,sun8i-h3-system-controller"
> > + "allwinner,sun8i-a64-system-controller"
>
> While sun8i might make some sense technically, all 64-bit sunxi
> compatible strings use the sun50i prefix to follow the Allwinner naming.
> So this should read:
> "allwinner,sun50i-a64-system-controller"
>
> Also I am wondering if we should add a compatible string for the H5
> (support for that SoC is in -next already):
> "allwinner,sun50i-h5-system-controller"
>
> Cheers,
> Andre.
>
I agree with sun50i-a64-system-controller, the sun8i-a64 is a copy/paste error.
I will add sun50i-h5-system-controller since all xxx-system-controller are just hypothetic compatible.
Thanks
Regards
On Wed, Apr 12, 2017 at 02:41:53PM +0200, Maxime Ripard wrote:
> On Wed, Apr 12, 2017 at 01:13:55PM +0200, Corentin Labbe wrote:
> > The dwmac-sun8i is an Ethernet MAC that supports 10/100/1000 Mbit
> > connections. It is very similar to the device found in the Allwinner
> > H3, but lacks the internal 100 Mbit PHY and its associated control
> > bits.
> > This adds the necessary bits to the Allwinner A64 SoC .dtsi, but keeps
> > it disabled at this level.
> >
> > Signed-off-by: Corentin Labbe <[email protected]>
> > ---
> > arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 37 +++++++++++++++++++++++++++
> > 1 file changed, 37 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> > index 0b0f4ab..2569827 100644
> > --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> > @@ -287,6 +287,23 @@
> > bias-pull-up;
> > };
> >
> > + rmii_pins: rmii_pins {
> > + pins = "PD10", "PD11", "PD13", "PD14",
> > + "PD17", "PD18", "PD19", "PD20",
> > + "PD22", "PD23";
>
> Please align the wrapped lines on the first pin.
>
OK
> > + function = "emac";
> > + drive-strength = <40>;
>
> Do you actually need that for all the boards, or only a few of them?
I have tried to use lower value without success on some boards. (opipc/pine64 in my memory)
Regards
Corentin Labbe
On Mon, Apr 24, 2017 at 8:24 PM, Corentin Labbe
<[email protected]> wrote:
> On Wed, Apr 12, 2017 at 02:41:53PM +0200, Maxime Ripard wrote:
>> On Wed, Apr 12, 2017 at 01:13:55PM +0200, Corentin Labbe wrote:
>> > The dwmac-sun8i is an Ethernet MAC that supports 10/100/1000 Mbit
>> > connections. It is very similar to the device found in the Allwinner
>> > H3, but lacks the internal 100 Mbit PHY and its associated control
>> > bits.
>> > This adds the necessary bits to the Allwinner A64 SoC .dtsi, but keeps
>> > it disabled at this level.
>> >
>> > Signed-off-by: Corentin Labbe <[email protected]>
>> > ---
>> > arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 37 +++++++++++++++++++++++++++
>> > 1 file changed, 37 insertions(+)
>> >
>> > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
>> > index 0b0f4ab..2569827 100644
>> > --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
>> > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
>> > @@ -287,6 +287,23 @@
>> > bias-pull-up;
>> > };
>> >
>> > + rmii_pins: rmii_pins {
>> > + pins = "PD10", "PD11", "PD13", "PD14",
>> > + "PD17", "PD18", "PD19", "PD20",
>> > + "PD22", "PD23";
>>
>> Please align the wrapped lines on the first pin.
>>
>
> OK
>
>> > + function = "emac";
>> > + drive-strength = <40>;
>>
>> Do you actually need that for all the boards, or only a few of them?
>
> I have tried to use lower value without success on some boards. (opipc/pine64 in my memory)
FYI we need them for all the boards that use RGMII.
The signals at gigabit speed run at 125 MHz DDR.
For RMII we probably don't need it. Even at 100 Mbps,
it's only 50 MHz SDR. drive-strength = <30> should be
enough.
ChenYu