This is the start of the stable review cycle for the 4.14.74 release.
There are 137 patches in this series, all will be posted as a response
to this one. If anyone has any issues with these being applied, please
let me know.
Responses should be made by Thu Oct 4 13:24:18 UTC 2018.
Anything received after that time might be too late.
The whole patch series can be found in one patch at:
https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.14.74-rc1.gz
or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.14.y
and the diffstat can be found below.
thanks,
greg k-h
-------------
Pseudo-Shortlog of commits:
Greg Kroah-Hartman <[email protected]>
Linux 4.14.74-rc1
Randy Dunlap <[email protected]>
x86/pti: Fix section mismatch warning/error
Mika Westerberg <[email protected]>
i2c: i801: Allow ACPI AML access I/O ports not reserved for SMBus
Marc Zyngier <[email protected]>
arm/arm64: smccc-1.1: Handle function result as parameters
Marc Zyngier <[email protected]>
arm/arm64: smccc-1.1: Make return values unsigned long
Tony Lindgren <[email protected]>
ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
James Smart <[email protected]>
nvme-fcloop: Fix dropped LS's to removed target port
Linus Walleij <[email protected]>
ata: ftide010: Add a quirk for SQ201
Rex Zhu <[email protected]>
drm/amdgpu: Update power state at the end of smu hw_init.
Rex Zhu <[email protected]>
drm/amdgpu: Enable/disable gfx PG feature in rlc safe mode
Leonard Crestez <[email protected]>
Revert "ARM: dts: imx7d: Invert legacy PCI irq mapping"
Dan Carpenter <[email protected]>
hwmon: (adt7475) Make adt7475_read_word() return errors
Lothar Felten <[email protected]>
hwmon: (ina2xx) fix sysfs shunt resistor read access
Srikanth Jampala <[email protected]>
crypto: cavium/nitrox - fix for command corruption in queue full case with backlog submissions.
Bo Chen <[email protected]>
e1000: ensure to free old tx/rx rings in set_ringparam()
Bo Chen <[email protected]>
e1000: check on netif_running() before calling e1000_up()
Huazhong Tan <[email protected]>
net: hns: fix skb->truesize underestimation
Huazhong Tan <[email protected]>
net: hns: fix length and page_offset overflow when CONFIG_ARM64_64K_PAGES
John Fastabend <[email protected]>
bpf: sockmap: write_space events need to be passed to TCP handler
John Fastabend <[email protected]>
tls: possible hang when do_tcp_sendpages hits sndbuf is full case
Eric Sandeen <[email protected]>
isofs: reject hardware sector size > 2048 bytes
Anson Huang <[email protected]>
thermal: of-thermal: disable passive polling when thermal zone is disabled
Tomer Tayar <[email protected]>
qed: Avoid sending mailbox commands when MFW is not responsive
Tomer Tayar <[email protected]>
qed: Prevent a possible deadlock during driver load and unload
Tomer Tayar <[email protected]>
qed: Wait for MCP halt and resume commands to take place
Tomer Tayar <[email protected]>
qed: Wait for ready indication before rereading the shmem
Dave Martin <[email protected]>
arm64: KVM: Tighten guest core register access from userspace
Uwe Kleine-König <[email protected]>
serial: imx: restore handshaking irq for imx1
Chris Wilson <[email protected]>
drm/i915: Remove vma from object on destroy, not close
Amir Goldstein <[email protected]>
ovl: hash non-dir by lower inode for fsnotify
Steve Wise <[email protected]>
RDMA/uverbs: Atomically flush and mark closed the comp event queue
Michael J. Ruhl <[email protected]>
IB/hfi1: Fix context recovery when PBC has an UnsupportedVL
Michael J. Ruhl <[email protected]>
IB/hfi1: Invalid user input can result in crash
Ira Weiny <[email protected]>
IB/hfi1: Fix SL array bounds check
Bart Van Assche <[email protected]>
IB/srp: Avoid that sg_reset -d ${srp_device} triggers an infinite loop
Aaron Ma <[email protected]>
Input: elantech - enable middle button of touchpad on ThinkPad P72
Alan Stern <[email protected]>
USB: remove LPM management from usb_driver_claim_interface()
Sebastian Andrzej Siewior <[email protected]>
Revert "usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()"
Oliver Neukum <[email protected]>
USB: usbdevfs: restore warning for nonsensical flags
Oliver Neukum <[email protected]>
USB: usbdevfs: sanitize flags more
ming_qian <[email protected]>
media: uvcvideo: Support realtek's UVC 1.5 device
Alexey Dobriyan <[email protected]>
slub: make ->cpu_partial unsigned int
Bin Liu <[email protected]>
usb: musb: dsps: do not disable CPPI41 irq in driver teardown
Alan Stern <[email protected]>
USB: handle NULL config in usb_find_alt_setting()
Alan Stern <[email protected]>
USB: fix error handling in usb_driver_claim_interface()
Yu Zhao <[email protected]>
regulator: fix crash caused by null driver data
Geert Uytterhoeven <[email protected]>
spi: rspi: Fix interrupted DMA transfers
Geert Uytterhoeven <[email protected]>
spi: rspi: Fix invalid SPI use during system suspend
Hiromitsu Yamasaki <[email protected]>
spi: sh-msiof: Fix handling of write value for SISTR register
Gaku Inami <[email protected]>
spi: sh-msiof: Fix invalid SPI use during system suspend
Marcel Ziswiler <[email protected]>
spi: tegra20-slink: explicitly enable/disable clock
Alexander Shishkin <[email protected]>
intel_th: Fix device removal logic
Christophe Leroy <[email protected]>
serial: cpm_uart: return immediately from console poll
Stefan Agner <[email protected]>
tty: serial: lpuart: avoid leaking struct tty_struct
Feng Tang <[email protected]>
x86/mm: Expand static page table for fixmap space
Andy Whitcroft <[email protected]>
floppy: Do not copy a kernel pointer to user memory in FDGETPRM ioctl
Kevin Hilman <[email protected]>
ARM: dts: dra7: fix DCAN node addresses
William Breathitt Gray <[email protected]>
iio: 104-quad-8: Fix off-by-one error in register selection
Oleksandr Andrushchenko <[email protected]>
Input: xen-kbdfront - fix multi-touch XenStore node's locations
Konstantin Khorenko <[email protected]>
fs/lock: skip lock owner pid translation in case we are in init_pid_ns
Johan Hovold <[email protected]>
EDAC: Fix memleak in module init error path
J. Bruce Fields <[email protected]>
nfsd: fix corrupted reply to badly ordered compound
Nadav Amit <[email protected]>
gpio: Fix wrong rounding in gpio-menz127
Jessica Yu <[email protected]>
module: exclude SHN_UNDEF symbols from kallsyms api
Liam Girdwood <[email protected]>
ASoC: dapm: Fix potential DAI widget pointer deref when linking DAIs
Johan Hovold <[email protected]>
EDAC, i7core: Fix memleaks and use-after-free on probe and remove
Shivasharan S <[email protected]>
scsi: megaraid_sas: Update controller info during resume
Andreas Gruenbacher <[email protected]>
iomap: complete partial direct I/O writes synchronously
Zhouyang Jia <[email protected]>
scsi: bnx2i: add error handling for ioremap_nocache
Kan Liang <[email protected]>
perf/x86/intel/lbr: Fix incomplete LBR call stack
Masahiro Yamada <[email protected]>
MIPS: boot: fix build rule of vmlinux.its.S
Zhouyang Jia <[email protected]>
HID: hid-ntrig: add error handling for sysfs_create_group
Viresh Kumar <[email protected]>
arm: dts: mediatek: Add missing cooling device properties for CPUs
Ethan Tuttle <[email protected]>
ARM: mvebu: declare asm symbols as character arrays in pmsu.c
Tony Lindgren <[email protected]>
wlcore: Add missing PM call for wlcore_cmd_wait_for_event_or_timeout()
Stefan Agner <[email protected]>
brcmsmac: fix wrap around in conversion from constant to s16
Dan Carpenter <[email protected]>
rndis_wlan: potential buffer overflow in rndis_wlan_auth_indication()
Niklas Cassel <[email protected]>
ath10k: transmit queued frames after processing rx packets
Jernej Skrabec <[email protected]>
drm/sun4i: Fix releasing node when enumerating enpoints
Brandon Maier <[email protected]>
net: phy: xgmiitorgmii: Check phy_driver ready before accessing
Ben Greear <[email protected]>
ath10k: protect ath10k_htt_rx_ring_free with rx_ring.lock
Brandon Maier <[email protected]>
net: phy: xgmiitorgmii: Check read_status results
Kai-Heng Feng <[email protected]>
ALSA: hda: Add AZX_DCAPS_PM_RUNTIME for AMD Raven Ridge
Zhouyang Jia <[email protected]>
media: tm6000: add error handling for dvb_register_adapter
Zhouyang Jia <[email protected]>
drivers/tty: add error handling for pcmcia_loop_config
Alistair Strachan <[email protected]>
staging: android: ashmem: Fix mmap size validation
Javier Martinez Canillas <[email protected]>
media: omap3isp: zero-initialize the isp cam_xclk{a,b} initial data
Akinobu Mita <[email protected]>
media: soc_camera: ov772x: correct setting of banding filter
Akinobu Mita <[email protected]>
media: s3c-camif: ignore -ENOIOCTLCMD from v4l2_subdev_call for s_power
Nicholas Mc Guire <[email protected]>
ALSA: snd-aoa: add of_node_put() in error path
Thomas Gleixner <[email protected]>
posix-timers: Sanitize overrun handling
Thomas Gleixner <[email protected]>
posix-timers: Make forward callback return s64
Akinobu Mita <[email protected]>
iio: accel: adxl345: convert address field usage in iio_chan_spec
Peter Rosin <[email protected]>
mtd: rawnand: atmel: add module param to avoid using dma
Vasily Gorbik <[email protected]>
s390/extmem: fix gcc 8 stringop-overflow warning
Vasily Gorbik <[email protected]>
s390/scm_blk: correct numa_node in scm_blk_dev_setup
Vasily Gorbik <[email protected]>
s390/dasd: correct numa_node in dasd_alloc_queue
Thomas Gleixner <[email protected]>
alarmtimer: Prevent overflow for relative nanosleep
Heiko Carstens <[email protected]>
s390/sysinfo: add missing #ifdef CONFIG_PROC_FS
Alexey Kardashevskiy <[email protected]>
powerpc/powernv/ioda2: Reduce upper limit for DMA window size
Alagu Sankar <[email protected]>
ath10k: sdio: set skb len for all rx packets
Alagu Sankar <[email protected]>
ath10k: sdio: use same endpoint id for all packets in a bundle
Julia Lawall <[email protected]>
usb: wusbcore: security: cast sizeof to int for comparison
Bart Van Assche <[email protected]>
scsi: target: Avoid that EXTENDED COPY commands trigger lock inversion
Breno Leitao <[email protected]>
scsi: ibmvscsi: Improve strings handling
Bart Van Assche <[email protected]>
scsi: klist: Make it safe to use klists in atomic context
Bart Van Assche <[email protected]>
scsi: target/iscsi: Make iscsit_ta_authentication() respect the output buffer size
Viresh Kumar <[email protected]>
ARM: dts: ls1021a: Add missing cooling device properties for CPUs
Jan Beulich <[email protected]>
x86/entry/64: Add two more instruction suffixes
Dave Gerlach <[email protected]>
ARM: hwmod: RTC: Don't assume lock/unlock will be called with irq enabled
Andy Shevchenko <[email protected]>
x86/tsc: Add missing header to tsc_msr.c
Peter Seiderer <[email protected]>
media: staging/imx: fill vb2_v4l2_buffer field entry
Alexey Khoroshilov <[email protected]>
media: fsl-viu: fix error handling in viu_of_probe()
Hari Bathini <[email protected]>
powerpc/kdump: Handle crashkernel memory reservation failure
Tarick Bedeir <[email protected]>
IB/mlx4: Test port number before querying type.
Sylwester Nawrocki <[email protected]>
media: exynos4-is: Prevent NULL pointer dereference in __isp_video_try_fmt()
Dan Carpenter <[email protected]>
IB/core: type promotion bug in rdma_rw_init_one_mr()
Leon Romanovsky <[email protected]>
RDMA/i40w: Hold read semaphore while looking after VMA
Dan Carpenter <[email protected]>
RDMA/bnxt_re: Fix a couple off by one bugs
Guoqing Jiang <[email protected]>
md-cluster: clear another node's suspend_area after the copy is finished
Benjamin Tissoires <[email protected]>
power: remove possible deadlock when unregistering power_supply
Vasily Gorbik <[email protected]>
s390/mm: correct allocate_pgste proc_handler callback
Niklas Cassel <[email protected]>
iommu/msm: Don't call iommu_device_{,un}link from atomic context
Michael Scott <[email protected]>
6lowpan: iphc: reset mac_header after decompress to fix panic
Johan Hovold <[email protected]>
USB: serial: kobil_sct: fix modem-status error handling
Jian-Hong Pan <[email protected]>
Bluetooth: Add a new Realtek 8723DE ID 0bda:b009
Zhen Lei <[email protected]>
iommu/amd: make sure TLB to be flushed before IOVA freed
Sudeep Holla <[email protected]>
power: vexpress: fix corruption in notifier registration
Anton Vasilyev <[email protected]>
uwb: hwa-rc: fix memory leak at probe
Geert Uytterhoeven <[email protected]>
serial: sh-sci: Stop RX FIFO timer during port shutdown
Johan Hovold <[email protected]>
misc: sram: enable clock before registering regions
Hans de Goede <[email protected]>
power: supply: axp288_charger: Fix initial constant_charge_current value
Colin Ian King <[email protected]>
staging: rts5208: fix missing error check on call to rtsx_write_register
Dan Williams <[email protected]>
x86/numa_emulation: Fix emulated-to-physical node mapping
Dan Carpenter <[email protected]>
vmci: type promotion bug in qp_host_get_user_memory()
Matt Ranostay <[email protected]>
tsl2550: fix lux1_input error in low light
Akinobu Mita <[email protected]>
iio: adc: ina2xx: avoid kthread_stop() with stale task_struct
Stafford Horne <[email protected]>
crypto: skcipher - Fix -Wstringop-truncation warnings
-------------
Diffstat:
Documentation/hwmon/ina2xx | 2 +-
Makefile | 4 +-
arch/arm/boot/dts/dra7.dtsi | 4 +-
arch/arm/boot/dts/imx7d.dtsi | 12 +-
arch/arm/boot/dts/ls1021a.dtsi | 1 +
arch/arm/boot/dts/mt7623.dtsi | 3 +
arch/arm/boot/dts/omap4-droid4-xt894.dts | 2 +-
arch/arm/mach-mvebu/pmsu.c | 6 +-
arch/arm/mach-omap2/omap_hwmod_reset.c | 12 +-
arch/arm64/kvm/guest.c | 45 +++++
arch/mips/boot/Makefile | 6 +-
arch/powerpc/kernel/machine_kexec.c | 7 +-
arch/powerpc/platforms/powernv/pci-ioda.c | 2 +-
arch/s390/kernel/sysinfo.c | 4 +
arch/s390/mm/extmem.c | 4 +-
arch/s390/mm/pgalloc.c | 2 +-
arch/x86/entry/entry_64.S | 4 +-
arch/x86/events/intel/lbr.c | 32 +++-
arch/x86/events/perf_event.h | 1 +
arch/x86/include/asm/fixmap.h | 10 ++
arch/x86/include/asm/pgtable_64.h | 3 +-
arch/x86/kernel/head64.c | 4 +-
arch/x86/kernel/head_64.S | 16 +-
arch/x86/kernel/tsc_msr.c | 1 +
arch/x86/mm/numa_emulation.c | 2 +-
arch/x86/mm/pgtable.c | 9 +
arch/x86/mm/pti.c | 2 +-
arch/x86/xen/mmu_pv.c | 8 +-
crypto/ablkcipher.c | 2 +
crypto/blkcipher.c | 1 +
drivers/ata/pata_ftide010.c | 27 +--
drivers/block/floppy.c | 3 +
drivers/bluetooth/btusb.c | 1 +
drivers/crypto/cavium/nitrox/nitrox_dev.h | 3 +-
drivers/crypto/cavium/nitrox/nitrox_lib.c | 1 +
drivers/crypto/cavium/nitrox/nitrox_reqmgr.c | 57 ++++---
drivers/edac/edac_mc_sysfs.c | 6 +-
drivers/edac/i7core_edac.c | 22 ++-
drivers/gpio/gpio-menz127.c | 4 +-
drivers/gpu/drm/amd/amdgpu/gfx_v8_0.c | 11 +-
drivers/gpu/drm/amd/amdgpu/kv_dpm.c | 4 +-
drivers/gpu/drm/amd/amdgpu/si_dpm.c | 3 +-
drivers/gpu/drm/i915/i915_gem.c | 3 +-
drivers/gpu/drm/i915/i915_vma.c | 4 +-
drivers/gpu/drm/sun4i/sun4i_drv.c | 3 +-
drivers/hid/hid-ntrig.c | 2 +
drivers/hwmon/adt7475.c | 14 +-
drivers/hwmon/ina2xx.c | 13 +-
drivers/hwtracing/intel_th/core.c | 3 +-
drivers/i2c/busses/i2c-i801.c | 9 +-
drivers/iio/accel/adxl345_core.c | 21 ++-
drivers/iio/adc/ina2xx-adc.c | 17 +-
drivers/iio/counter/104-quad-8.c | 2 +-
drivers/infiniband/core/rw.c | 2 +-
drivers/infiniband/core/uverbs_main.c | 1 +
drivers/infiniband/hw/bnxt_re/qplib_sp.c | 4 +-
drivers/infiniband/hw/hfi1/pio.c | 9 +-
drivers/infiniband/hw/hfi1/user_sdma.c | 2 +-
drivers/infiniband/hw/hfi1/verbs.c | 8 +-
drivers/infiniband/hw/i40iw/i40iw_verbs.c | 2 +
drivers/infiniband/hw/mlx4/qp.c | 2 +-
drivers/infiniband/ulp/srp/ib_srp.c | 6 +-
drivers/input/misc/xen-kbdfront.c | 8 +-
drivers/input/mouse/elantech.c | 2 +
drivers/iommu/amd_iommu.c | 2 +-
drivers/iommu/msm_iommu.c | 16 +-
drivers/md/md-cluster.c | 19 ++-
drivers/media/i2c/soc_camera/ov772x.c | 2 +-
drivers/media/platform/exynos4-is/fimc-isp-video.c | 11 +-
drivers/media/platform/fsl-viu.c | 38 +++--
drivers/media/platform/omap3isp/isp.c | 2 +-
drivers/media/platform/s3c-camif/camif-capture.c | 2 +
drivers/media/usb/tm6000/tm6000-dvb.c | 5 +
drivers/media/usb/uvc/uvc_video.c | 24 ++-
drivers/misc/sram.c | 13 +-
drivers/misc/tsl2550.c | 2 +-
drivers/misc/vmw_vmci/vmci_queue_pair.c | 4 +-
drivers/mtd/nand/atmel/nand-controller.c | 7 +-
drivers/net/ethernet/hisilicon/hns/hnae.h | 6 +-
drivers/net/ethernet/hisilicon/hns/hns_enet.c | 2 +-
drivers/net/ethernet/intel/e1000/e1000_ethtool.c | 7 +-
drivers/net/ethernet/qlogic/qed/qed_mcp.c | 187 +++++++++++++++++----
drivers/net/ethernet/qlogic/qed/qed_mcp.h | 27 ++-
drivers/net/ethernet/qlogic/qed/qed_reg_addr.h | 2 +
drivers/net/phy/xilinx_gmii2rgmii.c | 10 +-
drivers/net/wireless/ath/ath10k/htt_rx.c | 5 +-
drivers/net/wireless/ath/ath10k/mac.c | 1 +
drivers/net/wireless/ath/ath10k/sdio.c | 9 +-
.../broadcom/brcm80211/brcmsmac/phy/phy_qmath.c | 2 +-
drivers/net/wireless/rndis_wlan.c | 2 +
drivers/net/wireless/ti/wlcore/cmd.c | 6 +
drivers/nvme/target/fcloop.c | 3 +-
drivers/power/reset/vexpress-poweroff.c | 12 +-
drivers/power/supply/axp288_charger.c | 2 +-
drivers/power/supply/power_supply_core.c | 11 +-
drivers/regulator/core.c | 2 +-
drivers/s390/block/dasd.c | 1 +
drivers/s390/block/scm_blk.c | 1 +
drivers/scsi/bnx2i/bnx2i_hwi.c | 2 +
drivers/scsi/ibmvscsi/ibmvscsi.c | 4 +-
drivers/scsi/megaraid/megaraid_sas_base.c | 3 +
drivers/spi/spi-rspi.c | 34 +++-
drivers/spi/spi-sh-msiof.c | 28 ++-
drivers/spi/spi-tegra20-slink.c | 31 +++-
drivers/staging/android/ashmem.c | 6 +
drivers/staging/media/imx/imx-ic-prpencvf.c | 1 +
drivers/staging/media/imx/imx-media-csi.c | 1 +
drivers/staging/rts5208/sd.c | 2 +-
drivers/target/iscsi/iscsi_target_tpg.c | 3 +-
drivers/target/target_core_device.c | 22 ++-
drivers/thermal/of-thermal.c | 7 +-
drivers/tty/serial/8250/serial_cs.c | 6 +-
drivers/tty/serial/cpm_uart/cpm_uart_core.c | 10 +-
drivers/tty/serial/fsl_lpuart.c | 3 +-
drivers/tty/serial/imx.c | 8 +
drivers/tty/serial/sh-sci.c | 2 +
drivers/usb/class/cdc-wdm.c | 2 +-
drivers/usb/core/devio.c | 24 ++-
drivers/usb/core/driver.c | 28 +--
drivers/usb/core/usb.c | 2 +
drivers/usb/musb/musb_dsps.c | 12 +-
drivers/usb/serial/kobil_sct.c | 12 +-
drivers/usb/wusbcore/security.c | 2 +-
drivers/uwb/hwa-rc.c | 1 +
fs/iomap.c | 21 +--
fs/isofs/inode.c | 7 +
fs/locks.c | 7 +
fs/nfsd/nfs4proc.c | 1 +
fs/overlayfs/inode.c | 62 +++++--
include/linux/arm-smccc.h | 38 +++--
include/linux/platform_data/ina2xx.h | 2 +-
include/linux/posix-timers.h | 4 +-
include/linux/power_supply.h | 1 +
include/linux/slub_def.h | 3 +-
kernel/bpf/sockmap.c | 3 +
kernel/module.c | 6 +-
kernel/time/alarmtimer.c | 7 +-
kernel/time/posix-cpu-timers.c | 2 +-
kernel/time/posix-timers.c | 33 ++--
kernel/time/posix-timers.h | 2 +-
lib/klist.c | 10 +-
mm/slub.c | 6 +-
net/6lowpan/iphc.c | 1 +
net/tls/tls_main.c | 9 +-
sound/aoa/core/gpio-feature.c | 4 +-
sound/pci/hda/hda_intel.c | 3 +-
sound/soc/soc-dapm.c | 7 +
147 files changed, 1040 insertions(+), 390 deletions(-)
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Dan Carpenter <[email protected]>
[ Upstream commit 7fb2fd4e25fc1fb10dcb30b5519de257cfeae84c ]
The problem is that if get_user_pages_fast() fails and returns a
negative error code, it gets type promoted to a high positive value and
treated as a success.
Fixes: 06164d2b72aa ("VMCI: queue pairs implementation.")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/misc/vmw_vmci/vmci_queue_pair.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/drivers/misc/vmw_vmci/vmci_queue_pair.c
+++ b/drivers/misc/vmw_vmci/vmci_queue_pair.c
@@ -755,7 +755,7 @@ static int qp_host_get_user_memory(u64 p
retval = get_user_pages_fast((uintptr_t) produce_uva,
produce_q->kernel_if->num_pages, 1,
produce_q->kernel_if->u.h.header_page);
- if (retval < produce_q->kernel_if->num_pages) {
+ if (retval < (int)produce_q->kernel_if->num_pages) {
pr_debug("get_user_pages_fast(produce) failed (retval=%d)",
retval);
qp_release_pages(produce_q->kernel_if->u.h.header_page,
@@ -767,7 +767,7 @@ static int qp_host_get_user_memory(u64 p
retval = get_user_pages_fast((uintptr_t) consume_uva,
consume_q->kernel_if->num_pages, 1,
consume_q->kernel_if->u.h.header_page);
- if (retval < consume_q->kernel_if->num_pages) {
+ if (retval < (int)consume_q->kernel_if->num_pages) {
pr_debug("get_user_pages_fast(consume) failed (retval=%d)",
retval);
qp_release_pages(consume_q->kernel_if->u.h.header_page,
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Johan Hovold <[email protected]>
[ Upstream commit d5b9653dd2bb7a2b1c8cc783c5d3b607bbb6b271 ]
Make sure to enable the clock before registering regions and exporting
partitions to user space at which point we must be prepared for I/O.
Fixes: ee895ccdf776 ("misc: sram: fix enabled clock leak on error path")
Signed-off-by: Johan Hovold <[email protected]>
Reviewed-by: Vladimir Zapolskiy <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/misc/sram.c | 13 +++++++------
1 file changed, 7 insertions(+), 6 deletions(-)
--- a/drivers/misc/sram.c
+++ b/drivers/misc/sram.c
@@ -391,23 +391,23 @@ static int sram_probe(struct platform_de
if (IS_ERR(sram->pool))
return PTR_ERR(sram->pool);
- ret = sram_reserve_regions(sram, res);
- if (ret)
- return ret;
-
sram->clk = devm_clk_get(sram->dev, NULL);
if (IS_ERR(sram->clk))
sram->clk = NULL;
else
clk_prepare_enable(sram->clk);
+ ret = sram_reserve_regions(sram, res);
+ if (ret)
+ goto err_disable_clk;
+
platform_set_drvdata(pdev, sram);
init_func = of_device_get_match_data(&pdev->dev);
if (init_func) {
ret = init_func();
if (ret)
- goto err_disable_clk;
+ goto err_free_partitions;
}
dev_dbg(sram->dev, "SRAM pool: %zu KiB @ 0x%p\n",
@@ -415,10 +415,11 @@ static int sram_probe(struct platform_de
return 0;
+err_free_partitions:
+ sram_free_partitions(sram);
err_disable_clk:
if (sram->clk)
clk_disable_unprepare(sram->clk);
- sram_free_partitions(sram);
return ret;
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Andy Shevchenko <[email protected]>
[ Upstream commit dbd0fbc76c77daac08ddd245afdcbade0d506e19 ]
Add a missing header otherwise compiler warns about missed prototype:
CC arch/x86/kernel/tsc_msr.o
arch/x86/kernel/tsc_msr.c:73:15: warning: no previous prototype for ‘cpu_khz_from_msr’ [-Wmissing-prototypes]
unsigned long cpu_khz_from_msr(void)
^~~~~~~~~~~~~~~~
Signed-off-by: Andy Shevchenko <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: "H. Peter Anvin" <[email protected]>
Cc: Pavel Tatashin <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/x86/kernel/tsc_msr.c | 1 +
1 file changed, 1 insertion(+)
--- a/arch/x86/kernel/tsc_msr.c
+++ b/arch/x86/kernel/tsc_msr.c
@@ -12,6 +12,7 @@
#include <asm/setup.h>
#include <asm/apic.h>
#include <asm/param.h>
+#include <asm/tsc.h>
#define MAX_NUM_FREQS 9
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Dave Gerlach <[email protected]>
[ Upstream commit 6d609b35c815ba20132b7b64bcca04516bb17c56 ]
When the RTC lock and unlock functions were introduced it was likely
assumed that they would always be called from irq enabled context, hence
the use of local_irq_disable/enable. This is no longer true as the
RTC+DDR path makes a late call during the suspend path after irqs
have been disabled to enable the RTC hwmod which calls both unlock and
lock, leading to IRQs being reenabled through the local_irq_enable call
in omap_hwmod_rtc_lock call.
To avoid this change the local_irq_disable/enable to
local_irq_save/restore to ensure that from whatever context this is
called the proper IRQ configuration is maintained.
Signed-off-by: Dave Gerlach <[email protected]>
Signed-off-by: Keerthy <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/arm/mach-omap2/omap_hwmod_reset.c | 12 ++++++++----
1 file changed, 8 insertions(+), 4 deletions(-)
--- a/arch/arm/mach-omap2/omap_hwmod_reset.c
+++ b/arch/arm/mach-omap2/omap_hwmod_reset.c
@@ -92,11 +92,13 @@ static void omap_rtc_wait_not_busy(struc
*/
void omap_hwmod_rtc_unlock(struct omap_hwmod *oh)
{
- local_irq_disable();
+ unsigned long flags;
+
+ local_irq_save(flags);
omap_rtc_wait_not_busy(oh);
omap_hwmod_write(OMAP_RTC_KICK0_VALUE, oh, OMAP_RTC_KICK0_REG);
omap_hwmod_write(OMAP_RTC_KICK1_VALUE, oh, OMAP_RTC_KICK1_REG);
- local_irq_enable();
+ local_irq_restore(flags);
}
/**
@@ -110,9 +112,11 @@ void omap_hwmod_rtc_unlock(struct omap_h
*/
void omap_hwmod_rtc_lock(struct omap_hwmod *oh)
{
- local_irq_disable();
+ unsigned long flags;
+
+ local_irq_save(flags);
omap_rtc_wait_not_busy(oh);
omap_hwmod_write(0x0, oh, OMAP_RTC_KICK0_REG);
omap_hwmod_write(0x0, oh, OMAP_RTC_KICK1_REG);
- local_irq_enable();
+ local_irq_restore(flags);
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Jan Beulich <[email protected]>
[ Upstream commit 6709812f094d96543b443645c68daaa32d3d3e77 ]
Sadly, other than claimed in:
a368d7fd2a ("x86/entry/64: Add instruction suffix")
... there are two more instances which want to be adjusted.
As said there, omitting suffixes from instructions in AT&T mode is bad
practice when operand size cannot be determined by the assembler from
register operands, and is likely going to be warned about by upstream
gas in the future (mine does already).
Add the other missing suffixes here as well.
Signed-off-by: Jan Beulich <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Brian Gerst <[email protected]>
Cc: Denys Vlasenko <[email protected]>
Cc: H. Peter Anvin <[email protected]>
Cc: Josh Poimboeuf <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/x86/entry/entry_64.S | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/arch/x86/entry/entry_64.S
+++ b/arch/x86/entry/entry_64.S
@@ -88,7 +88,7 @@ END(native_usergs_sysret64)
.endm
.macro TRACE_IRQS_IRETQ_DEBUG
- bt $9, EFLAGS(%rsp) /* interrupts off? */
+ btl $9, EFLAGS(%rsp) /* interrupts off? */
jnc 1f
TRACE_IRQS_ON_DEBUG
1:
@@ -630,7 +630,7 @@ retint_kernel:
#ifdef CONFIG_PREEMPT
/* Interrupts are off */
/* Check if we need preemption */
- bt $9, EFLAGS(%rsp) /* were interrupts off? */
+ btl $9, EFLAGS(%rsp) /* were interrupts off? */
jnc 1f
0: cmpl $0, PER_CPU_VAR(__preempt_count)
jnz 1f
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Viresh Kumar <[email protected]>
[ Upstream commit 47768f372eae030db6fab5225f9504a820d2c07f ]
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/arm/boot/dts/ls1021a.dtsi | 1 +
1 file changed, 1 insertion(+)
--- a/arch/arm/boot/dts/ls1021a.dtsi
+++ b/arch/arm/boot/dts/ls1021a.dtsi
@@ -84,6 +84,7 @@
device_type = "cpu";
reg = <0xf01>;
clocks = <&clockgen 1 0>;
+ #cooling-cells = <2>;
};
};
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Johan Hovold <[email protected]>
[ Upstream commit a420b5d939ee58f1d950f0ea782834056520aeaa ]
Make sure to return -EIO in case of a short modem-status read request.
While at it, split the debug message to not include the (zeroed)
transfer-buffer content in case of errors.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/serial/kobil_sct.c | 12 ++++++++++--
1 file changed, 10 insertions(+), 2 deletions(-)
--- a/drivers/usb/serial/kobil_sct.c
+++ b/drivers/usb/serial/kobil_sct.c
@@ -397,12 +397,20 @@ static int kobil_tiocmget(struct tty_str
transfer_buffer_length,
KOBIL_TIMEOUT);
- dev_dbg(&port->dev, "%s - Send get_status_line_state URB returns: %i. Statusline: %02x\n",
- __func__, result, transfer_buffer[0]);
+ dev_dbg(&port->dev, "Send get_status_line_state URB returns: %i\n",
+ result);
+ if (result < 1) {
+ if (result >= 0)
+ result = -EIO;
+ goto out_free;
+ }
+
+ dev_dbg(&port->dev, "Statusline: %02x\n", transfer_buffer[0]);
result = 0;
if ((transfer_buffer[0] & SUSBCR_GSL_DSR) != 0)
result = TIOCM_DSR;
+out_free:
kfree(transfer_buffer);
return result;
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Bart Van Assche <[email protected]>
[ Upstream commit 624fa7790f80575a4ec28fbdb2034097dc18d051 ]
In the scsi_transport_srp implementation it cannot be avoided to
iterate over a klist from atomic context when using the legacy block
layer instead of blk-mq. Hence this patch that makes it safe to use
klists in atomic context. This patch avoids that lockdep reports the
following:
WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(&k->k_lock)->rlock);
local_irq_disable();
lock(&(&q->__queue_lock)->rlock);
lock(&(&k->k_lock)->rlock);
<Interrupt>
lock(&(&q->__queue_lock)->rlock);
stack backtrace:
Workqueue: kblockd blk_timeout_work
Call Trace:
dump_stack+0xa4/0xf5
check_usage+0x6e6/0x700
__lock_acquire+0x185d/0x1b50
lock_acquire+0xd2/0x260
_raw_spin_lock+0x32/0x50
klist_next+0x47/0x190
device_for_each_child+0x8e/0x100
srp_timed_out+0xaf/0x1d0 [scsi_transport_srp]
scsi_times_out+0xd4/0x410 [scsi_mod]
blk_rq_timed_out+0x36/0x70
blk_timeout_work+0x1b5/0x220
process_one_work+0x4fe/0xad0
worker_thread+0x63/0x5a0
kthread+0x1c1/0x1e0
ret_from_fork+0x24/0x30
See also commit c9ddf73476ff ("scsi: scsi_transport_srp: Fix shost to
rport translation").
Signed-off-by: Bart Van Assche <[email protected]>
Cc: Martin K. Petersen <[email protected]>
Cc: James Bottomley <[email protected]>
Acked-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
lib/klist.c | 10 ++++++----
1 file changed, 6 insertions(+), 4 deletions(-)
--- a/lib/klist.c
+++ b/lib/klist.c
@@ -336,8 +336,9 @@ struct klist_node *klist_prev(struct kli
void (*put)(struct klist_node *) = i->i_klist->put;
struct klist_node *last = i->i_cur;
struct klist_node *prev;
+ unsigned long flags;
- spin_lock(&i->i_klist->k_lock);
+ spin_lock_irqsave(&i->i_klist->k_lock, flags);
if (last) {
prev = to_klist_node(last->n_node.prev);
@@ -356,7 +357,7 @@ struct klist_node *klist_prev(struct kli
prev = to_klist_node(prev->n_node.prev);
}
- spin_unlock(&i->i_klist->k_lock);
+ spin_unlock_irqrestore(&i->i_klist->k_lock, flags);
if (put && last)
put(last);
@@ -377,8 +378,9 @@ struct klist_node *klist_next(struct kli
void (*put)(struct klist_node *) = i->i_klist->put;
struct klist_node *last = i->i_cur;
struct klist_node *next;
+ unsigned long flags;
- spin_lock(&i->i_klist->k_lock);
+ spin_lock_irqsave(&i->i_klist->k_lock, flags);
if (last) {
next = to_klist_node(last->n_node.next);
@@ -397,7 +399,7 @@ struct klist_node *klist_next(struct kli
next = to_klist_node(next->n_node.next);
}
- spin_unlock(&i->i_klist->k_lock);
+ spin_unlock_irqrestore(&i->i_klist->k_lock, flags);
if (put && last)
put(last);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Bart Van Assche <[email protected]>
[ Upstream commit 35bea5c84fd13c643cce63f0b5cd4b148f8c901d ]
Fixes: e48354ce078c ("iscsi-target: Add iSCSI fabric support for target v4.1")
Signed-off-by: Bart Van Assche <[email protected]>
Reviewed-by: Mike Christie <[email protected]>
Cc: Mike Christie <[email protected]>
Cc: Christoph Hellwig <[email protected]>
Cc: Hannes Reinecke <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/target/iscsi/iscsi_target_tpg.c | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
--- a/drivers/target/iscsi/iscsi_target_tpg.c
+++ b/drivers/target/iscsi/iscsi_target_tpg.c
@@ -633,8 +633,7 @@ int iscsit_ta_authentication(struct iscs
none = strstr(buf1, NONE);
if (none)
goto out;
- strncat(buf1, ",", strlen(","));
- strncat(buf1, NONE, strlen(NONE));
+ strlcat(buf1, "," NONE, sizeof(buf1));
if (iscsi_update_param_value(param, buf1) < 0)
return -EINVAL;
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Guoqing Jiang <[email protected]>
[ Upstream commit 010228e4a932ca1e8365e3b58c8e1e44c16ff793 ]
When one node leaves cluster or stops the resyncing
(resync or recovery) array, then other nodes need to
call recover_bitmaps to continue the unfinished task.
But we need to clear suspend_area later after other
nodes copy the resync information to their bitmap
(by call bitmap_copy_from_slot). Otherwise, all nodes
could write to the suspend_area even the suspend_area
is not handled by any node, because area_resyncing
returns 0 at the beginning of raid1_write_request.
Which means one node could write suspend_area while
another node is resyncing the same area, then data
could be inconsistent.
So let's clear suspend_area later to avoid above issue
with the protection of bm lock. Also it is straightforward
to clear suspend_area after nodes have copied the resync
info to bitmap.
Signed-off-by: Guoqing Jiang <[email protected]>
Reviewed-by: NeilBrown <[email protected]>
Signed-off-by: Shaohua Li <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/md/md-cluster.c | 19 ++++++++++---------
1 file changed, 10 insertions(+), 9 deletions(-)
--- a/drivers/md/md-cluster.c
+++ b/drivers/md/md-cluster.c
@@ -304,15 +304,6 @@ static void recover_bitmaps(struct md_th
while (cinfo->recovery_map) {
slot = fls64((u64)cinfo->recovery_map) - 1;
- /* Clear suspend_area associated with the bitmap */
- spin_lock_irq(&cinfo->suspend_lock);
- list_for_each_entry_safe(s, tmp, &cinfo->suspend_list, list)
- if (slot == s->slot) {
- list_del(&s->list);
- kfree(s);
- }
- spin_unlock_irq(&cinfo->suspend_lock);
-
snprintf(str, 64, "bitmap%04d", slot);
bm_lockres = lockres_init(mddev, str, NULL, 1);
if (!bm_lockres) {
@@ -331,6 +322,16 @@ static void recover_bitmaps(struct md_th
pr_err("md-cluster: Could not copy data from bitmap %d\n", slot);
goto clear_bit;
}
+
+ /* Clear suspend_area associated with the bitmap */
+ spin_lock_irq(&cinfo->suspend_lock);
+ list_for_each_entry_safe(s, tmp, &cinfo->suspend_list, list)
+ if (slot == s->slot) {
+ list_del(&s->list);
+ kfree(s);
+ }
+ spin_unlock_irq(&cinfo->suspend_lock);
+
if (hi > 0) {
if (lo < mddev->recovery_cp)
mddev->recovery_cp = lo;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Leon Romanovsky <[email protected]>
[ Upstream commit 5d9a2b0e28759e319a623da33940dbb3ce952b7d ]
VMA lookup is supposed to be performed while mmap_sem is held.
Fixes: f26c7c83395b ("i40iw: Add 2MB page support")
Signed-off-by: Leon Romanovsky <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/infiniband/hw/i40iw/i40iw_verbs.c | 2 ++
1 file changed, 2 insertions(+)
--- a/drivers/infiniband/hw/i40iw/i40iw_verbs.c
+++ b/drivers/infiniband/hw/i40iw/i40iw_verbs.c
@@ -1408,6 +1408,7 @@ static void i40iw_set_hugetlb_values(u64
struct vm_area_struct *vma;
struct hstate *h;
+ down_read(¤t->mm->mmap_sem);
vma = find_vma(current->mm, addr);
if (vma && is_vm_hugetlb_page(vma)) {
h = hstate_vma(vma);
@@ -1416,6 +1417,7 @@ static void i40iw_set_hugetlb_values(u64
iwmr->page_msk = huge_page_mask(h);
}
}
+ up_read(¤t->mm->mmap_sem);
}
/**
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Zhen Lei <[email protected]>
[ Upstream commit 3c120143f584360a13614787e23ae2cdcb5e5ccd ]
Although the mapping has already been removed in the page table, it maybe
still exist in TLB. Suppose the freed IOVAs is reused by others before the
flush operation completed, the new user can not correctly access to its
meomory.
Signed-off-by: Zhen Lei <[email protected]>
Fixes: b1516a14657a ('iommu/amd: Implement flush queue')
Signed-off-by: Joerg Roedel <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/iommu/amd_iommu.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/iommu/amd_iommu.c
+++ b/drivers/iommu/amd_iommu.c
@@ -2400,9 +2400,9 @@ static void __unmap_single(struct dma_op
}
if (amd_iommu_unmap_flush) {
- dma_ops_free_iova(dma_dom, dma_addr, pages);
domain_flush_tlb(&dma_dom->domain);
domain_flush_complete(&dma_dom->domain);
+ dma_ops_free_iova(dma_dom, dma_addr, pages);
} else {
pages = __roundup_pow_of_two(pages);
queue_iova(&dma_dom->iovad, dma_addr >> PAGE_SHIFT, pages, 0);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Akinobu Mita <[email protected]>
[ Upstream commit 30ed2b83343bd1e07884ca7355dac70d25ffc158 ]
When the subdevice doesn't provide s_power core ops callback, the
v4l2_subdev_call for s_power returns -ENOIOCTLCMD. If the subdevice
doesn't have the special handling for its power saving mode, the s_power
isn't required. So -ENOIOCTLCMD from the v4l2_subdev_call should be
ignored.
Cc: Hans Verkuil <[email protected]>
Signed-off-by: Akinobu Mita <[email protected]>
Acked-by: Sylwester Nawrocki <[email protected]>
Signed-off-by: Sakari Ailus <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/media/platform/s3c-camif/camif-capture.c | 2 ++
1 file changed, 2 insertions(+)
--- a/drivers/media/platform/s3c-camif/camif-capture.c
+++ b/drivers/media/platform/s3c-camif/camif-capture.c
@@ -117,6 +117,8 @@ static int sensor_set_power(struct camif
if (camif->sensor.power_count == !on)
err = v4l2_subdev_call(sensor->sd, core, s_power, on);
+ if (err == -ENOIOCTLCMD)
+ err = 0;
if (!err)
sensor->power_count += on ? 1 : -1;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Ethan Tuttle <[email protected]>
[ Upstream commit d0d378ff451a66e486488eec842e507d28145813 ]
With CONFIG_FORTIFY_SOURCE, memcpy uses the declared size of operands to
detect buffer overflows. If src or dest is declared as a char, attempts to
copy more than byte will result in a fortify_panic().
Address this problem in mvebu_setup_boot_addr_wa() by declaring
mvebu_boot_wa_start and mvebu_boot_wa_end as character arrays. Also remove
a couple addressof operators to avoid "arithmetic on pointer to an
incomplete type" compiler error.
See commit 54a7d50b9205 ("x86: mark kprobe templates as character arrays,
not single characters") for a similar fix.
Fixes "detected buffer overflow in memcpy" error during init on some mvebu
systems (armada-370-xp, armada-375):
(fortify_panic) from (mvebu_setup_boot_addr_wa+0xb0/0xb4)
(mvebu_setup_boot_addr_wa) from (mvebu_v7_cpu_pm_init+0x154/0x204)
(mvebu_v7_cpu_pm_init) from (do_one_initcall+0x7c/0x1a8)
(do_one_initcall) from (kernel_init_freeable+0x1bc/0x254)
(kernel_init_freeable) from (kernel_init+0x8/0x114)
(kernel_init) from (ret_from_fork+0x14/0x2c)
Signed-off-by: Ethan Tuttle <[email protected]>
Tested-by: Ethan Tuttle <[email protected]>
Signed-off-by: Gregory CLEMENT <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/arm/mach-mvebu/pmsu.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
--- a/arch/arm/mach-mvebu/pmsu.c
+++ b/arch/arm/mach-mvebu/pmsu.c
@@ -116,8 +116,8 @@ void mvebu_pmsu_set_cpu_boot_addr(int hw
PMSU_BOOT_ADDR_REDIRECT_OFFSET(hw_cpu));
}
-extern unsigned char mvebu_boot_wa_start;
-extern unsigned char mvebu_boot_wa_end;
+extern unsigned char mvebu_boot_wa_start[];
+extern unsigned char mvebu_boot_wa_end[];
/*
* This function sets up the boot address workaround needed for SMP
@@ -130,7 +130,7 @@ int mvebu_setup_boot_addr_wa(unsigned in
phys_addr_t resume_addr_reg)
{
void __iomem *sram_virt_base;
- u32 code_len = &mvebu_boot_wa_end - &mvebu_boot_wa_start;
+ u32 code_len = mvebu_boot_wa_end - mvebu_boot_wa_start;
mvebu_mbus_del_window(BOOTROM_BASE, BOOTROM_SIZE);
mvebu_mbus_add_window_by_id(crypto_eng_target, crypto_eng_attribute,
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Zhouyang Jia <[email protected]>
[ Upstream commit 44d4d51de9a3534a2b63d69efda02a10e66541e4 ]
When sysfs_create_group fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling sysfs_create_group.
Signed-off-by: Zhouyang Jia <[email protected]>
Signed-off-by: Jiri Kosina <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/hid/hid-ntrig.c | 2 ++
1 file changed, 2 insertions(+)
--- a/drivers/hid/hid-ntrig.c
+++ b/drivers/hid/hid-ntrig.c
@@ -955,6 +955,8 @@ static int ntrig_probe(struct hid_device
ret = sysfs_create_group(&hdev->dev.kobj,
&ntrig_attribute_group);
+ if (ret)
+ hid_err(hdev, "cannot create sysfs group\n");
return 0;
err_free:
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Johan Hovold <[email protected]>
[ Upstream commit 4708aa85d50cc6e962dfa8acf5ad4e0d290a21db ]
Make sure to use put_device() to free the initialised struct device so
that resources managed by driver core also gets released in the event of
a registration failure.
Signed-off-by: Johan Hovold <[email protected]>
Cc: Denis Kirjanov <[email protected]>
Cc: Mauro Carvalho Chehab <[email protected]>
Cc: linux-edac <[email protected]>
Fixes: 2d56b109e3a5 ("EDAC: Handle error path in edac_mc_sysfs_init() properly")
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Borislav Petkov <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/edac/edac_mc_sysfs.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
--- a/drivers/edac/edac_mc_sysfs.c
+++ b/drivers/edac/edac_mc_sysfs.c
@@ -1097,14 +1097,14 @@ int __init edac_mc_sysfs_init(void)
err = device_add(mci_pdev);
if (err < 0)
- goto out_dev_free;
+ goto out_put_device;
edac_dbg(0, "device %s created\n", dev_name(mci_pdev));
return 0;
- out_dev_free:
- kfree(mci_pdev);
+ out_put_device:
+ put_device(mci_pdev);
out:
return err;
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Alan Stern <[email protected]>
commit bd729f9d67aa9a303d8925bb8c4f06af25f407d1 upstream.
The syzbot fuzzing project found a use-after-free bug in the USB
core. The bug was caused by usbfs not unbinding from an interface
when the USB device file was closed, which led another process to
attempt the unbind later on, after the private data structure had been
deallocated.
The reason usbfs did not unbind the interface at the appropriate time
was because it thought the interface had never been claimed in the
first place. This was caused by the fact that
usb_driver_claim_interface() does not clean up properly when
device_bind_driver() returns an error. Although the error code gets
passed back to the caller, the iface->dev.driver pointer remains set
and iface->condition remains equal to USB_INTERFACE_BOUND.
This patch adds proper error handling to usb_driver_claim_interface().
Signed-off-by: Alan Stern <[email protected]>
Reported-by: [email protected]
CC: <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/core/driver.c | 15 +++++++++++++++
1 file changed, 15 insertions(+)
--- a/drivers/usb/core/driver.c
+++ b/drivers/usb/core/driver.c
@@ -565,6 +565,21 @@ int usb_driver_claim_interface(struct us
if (!lpm_disable_error)
usb_unlocked_enable_lpm(udev);
+ if (retval) {
+ dev->driver = NULL;
+ usb_set_intfdata(iface, NULL);
+ iface->needs_remote_wakeup = 0;
+ iface->condition = USB_INTERFACE_UNBOUND;
+
+ /*
+ * Unbound interfaces are always runtime-PM-disabled
+ * and runtime-PM-suspended
+ */
+ if (driver->supports_autosuspend)
+ pm_runtime_disable(dev);
+ pm_runtime_set_suspended(dev);
+ }
+
return retval;
}
EXPORT_SYMBOL_GPL(usb_driver_claim_interface);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Dan Carpenter <[email protected]>
[ Upstream commit 474e5a86067e5f12c97d1db8b170c7f45b53097a ]
The sgid_tbl->tbl[] array is allocated in bnxt_qplib_alloc_sgid_tbl().
It has sgid_tbl->max elements. So the > should be >= to prevent
accessing one element beyond the end of the array.
Fixes: 1ac5a4047975 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Signed-off-by: Dan Carpenter <[email protected]>
Acked-by: Selvin Xavier <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/infiniband/hw/bnxt_re/qplib_sp.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/drivers/infiniband/hw/bnxt_re/qplib_sp.c
+++ b/drivers/infiniband/hw/bnxt_re/qplib_sp.c
@@ -156,7 +156,7 @@ int bnxt_qplib_get_sgid(struct bnxt_qpli
struct bnxt_qplib_sgid_tbl *sgid_tbl, int index,
struct bnxt_qplib_gid *gid)
{
- if (index > sgid_tbl->max) {
+ if (index >= sgid_tbl->max) {
dev_err(&res->pdev->dev,
"QPLIB: Index %d exceeded SGID table max (%d)",
index, sgid_tbl->max);
@@ -361,7 +361,7 @@ int bnxt_qplib_get_pkey(struct bnxt_qpli
*pkey = 0xFFFF;
return 0;
}
- if (index > pkey_tbl->max) {
+ if (index >= pkey_tbl->max) {
dev_err(&res->pdev->dev,
"QPLIB: Index %d exceeded PKEY table max (%d)",
index, pkey_tbl->max);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Zhouyang Jia <[email protected]>
[ Upstream commit 85c634e919bd6ef17427f26a52920aeba12e16ee ]
When pcmcia_loop_config fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling pcmcia_loop_config.
Signed-off-by: Zhouyang Jia <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/tty/serial/8250/serial_cs.c | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
--- a/drivers/tty/serial/8250/serial_cs.c
+++ b/drivers/tty/serial/8250/serial_cs.c
@@ -637,8 +637,10 @@ static int serial_config(struct pcmcia_d
(link->has_func_id) &&
(link->socket->pcmcia_pfc == 0) &&
((link->func_id == CISTPL_FUNCID_MULTI) ||
- (link->func_id == CISTPL_FUNCID_SERIAL)))
- pcmcia_loop_config(link, serial_check_for_multi, info);
+ (link->func_id == CISTPL_FUNCID_SERIAL))) {
+ if (pcmcia_loop_config(link, serial_check_for_multi, info))
+ goto failed;
+ }
/*
* Apply any multi-port quirk.
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Stefan Agner <[email protected]>
[ Upstream commit c9a61469fc97672a08b2f798830a55ea6e03dc4a ]
The last value in the log_table wraps around to a negative value
since s16 has a value range of -32768 to 32767. This is not what
the table intends to represent. Use the closest positive value
32767.
This fixes a warning seen with clang:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_qmath.c:216:2: warning:
implicit conversion from 'int' to 's16' (aka 'short') changes
value from 32768
to -32768 [-Wconstant-conversion]
32768
^~~~~
1 warning generated.
Fixes: 4c0bfeaae9f9 ("brcmsmac: fix array out-of-bounds access in qm_log10")
Cc: Tobias Regnery <[email protected]>
Signed-off-by: Stefan Agner <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_qmath.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_qmath.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_qmath.c
@@ -213,7 +213,7 @@ static const s16 log_table[] = {
30498,
31267,
32024,
- 32768
+ 32767
};
#define LOG_TABLE_SIZE 32 /* log_table size */
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Tony Lindgren <[email protected]>
[ Upstream commit 4ec7cece87b3ed21ffcd407c62fb2f151a366bc1 ]
Otherwise we can get:
WARNING: CPU: 0 PID: 55 at drivers/net/wireless/ti/wlcore/io.h:84
I've only seen this few times with the runtime PM patches enabled
so this one is probably not needed before that. This seems to
work currently based on the current PM implementation timer. Let's
apply this separately though in case others are hitting this issue.
Signed-off-by: Tony Lindgren <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/wireless/ti/wlcore/cmd.c | 6 ++++++
1 file changed, 6 insertions(+)
--- a/drivers/net/wireless/ti/wlcore/cmd.c
+++ b/drivers/net/wireless/ti/wlcore/cmd.c
@@ -35,6 +35,7 @@
#include "wl12xx_80211.h"
#include "cmd.h"
#include "event.h"
+#include "ps.h"
#include "tx.h"
#include "hw_ops.h"
@@ -191,6 +192,10 @@ int wlcore_cmd_wait_for_event_or_timeout
timeout_time = jiffies + msecs_to_jiffies(WL1271_EVENT_TIMEOUT);
+ ret = wl1271_ps_elp_wakeup(wl);
+ if (ret < 0)
+ return ret;
+
do {
if (time_after(jiffies, timeout_time)) {
wl1271_debug(DEBUG_CMD, "timeout waiting for event %d",
@@ -222,6 +227,7 @@ int wlcore_cmd_wait_for_event_or_timeout
} while (!event);
out:
+ wl1271_ps_elp_sleep(wl);
kfree(events_vector);
return ret;
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Uwe Kleine-König <[email protected]>
commit 7e620984b62532783912312e334f3c48cdacbd5d upstream.
Back in 2015 when irda was dropped from the driver imx1 was broken. This
change reintroduces the support for the third interrupt of the UART.
Fixes: afe9cbb1a6ad ("serial: imx: drop support for IRDA")
Cc: stable <[email protected]>
Signed-off-by: Uwe Kleine-König <[email protected]>
Reviewed-by: Leonard Crestez <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/tty/serial/imx.c | 8 ++++++++
1 file changed, 8 insertions(+)
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -2213,6 +2213,14 @@ static int serial_imx_probe(struct platf
ret);
return ret;
}
+
+ ret = devm_request_irq(&pdev->dev, rtsirq, imx_rtsint, 0,
+ dev_name(&pdev->dev), sport);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to request rts irq: %d\n",
+ ret);
+ return ret;
+ }
} else {
ret = devm_request_irq(&pdev->dev, rxirq, imx_int, 0,
dev_name(&pdev->dev), sport);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Tomer Tayar <[email protected]>
[ Upstream commit f00d25f3154b676fcea4502a25b94bd7f142ca74 ]
The MFW might be reset and re-update its shared memory.
Upon the detection of such a reset the driver rereads this memory, but it
has to wait till the data is valid.
This patch adds the missing wait for a data ready indication.
Signed-off-by: Tomer Tayar <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/qlogic/qed/qed_mcp.c | 50 ++++++++++++++++++++++++------
1 file changed, 41 insertions(+), 9 deletions(-)
--- a/drivers/net/ethernet/qlogic/qed/qed_mcp.c
+++ b/drivers/net/ethernet/qlogic/qed/qed_mcp.c
@@ -182,18 +182,57 @@ int qed_mcp_free(struct qed_hwfn *p_hwfn
return 0;
}
+/* Maximum of 1 sec to wait for the SHMEM ready indication */
+#define QED_MCP_SHMEM_RDY_MAX_RETRIES 20
+#define QED_MCP_SHMEM_RDY_ITER_MS 50
+
static int qed_load_mcp_offsets(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt)
{
struct qed_mcp_info *p_info = p_hwfn->mcp_info;
+ u8 cnt = QED_MCP_SHMEM_RDY_MAX_RETRIES;
+ u8 msec = QED_MCP_SHMEM_RDY_ITER_MS;
u32 drv_mb_offsize, mfw_mb_offsize;
u32 mcp_pf_id = MCP_PF_ID(p_hwfn);
p_info->public_base = qed_rd(p_hwfn, p_ptt, MISC_REG_SHARED_MEM_ADDR);
- if (!p_info->public_base)
- return 0;
+ if (!p_info->public_base) {
+ DP_NOTICE(p_hwfn,
+ "The address of the MCP scratch-pad is not configured\n");
+ return -EINVAL;
+ }
p_info->public_base |= GRCBASE_MCP;
+ /* Get the MFW MB address and number of supported messages */
+ mfw_mb_offsize = qed_rd(p_hwfn, p_ptt,
+ SECTION_OFFSIZE_ADDR(p_info->public_base,
+ PUBLIC_MFW_MB));
+ p_info->mfw_mb_addr = SECTION_ADDR(mfw_mb_offsize, mcp_pf_id);
+ p_info->mfw_mb_length = (u16)qed_rd(p_hwfn, p_ptt,
+ p_info->mfw_mb_addr +
+ offsetof(struct public_mfw_mb,
+ sup_msgs));
+
+ /* The driver can notify that there was an MCP reset, and might read the
+ * SHMEM values before the MFW has completed initializing them.
+ * To avoid this, the "sup_msgs" field in the MFW mailbox is used as a
+ * data ready indication.
+ */
+ while (!p_info->mfw_mb_length && --cnt) {
+ msleep(msec);
+ p_info->mfw_mb_length =
+ (u16)qed_rd(p_hwfn, p_ptt,
+ p_info->mfw_mb_addr +
+ offsetof(struct public_mfw_mb, sup_msgs));
+ }
+
+ if (!cnt) {
+ DP_NOTICE(p_hwfn,
+ "Failed to get the SHMEM ready notification after %d msec\n",
+ QED_MCP_SHMEM_RDY_MAX_RETRIES * msec);
+ return -EBUSY;
+ }
+
/* Calculate the driver and MFW mailbox address */
drv_mb_offsize = qed_rd(p_hwfn, p_ptt,
SECTION_OFFSIZE_ADDR(p_info->public_base,
@@ -203,13 +242,6 @@ static int qed_load_mcp_offsets(struct q
"drv_mb_offsiz = 0x%x, drv_mb_addr = 0x%x mcp_pf_id = 0x%x\n",
drv_mb_offsize, p_info->drv_mb_addr, mcp_pf_id);
- /* Set the MFW MB address */
- mfw_mb_offsize = qed_rd(p_hwfn, p_ptt,
- SECTION_OFFSIZE_ADDR(p_info->public_base,
- PUBLIC_MFW_MB));
- p_info->mfw_mb_addr = SECTION_ADDR(mfw_mb_offsize, mcp_pf_id);
- p_info->mfw_mb_length = (u16)qed_rd(p_hwfn, p_ptt, p_info->mfw_mb_addr);
-
/* Get the current driver mailbox sequence before sending
* the first command
*/
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Tomer Tayar <[email protected]>
[ Upstream commit 76271809f49056f079e202bf6513d17b0d6dd34d ]
Successive iterations of halting and resuming the management chip (MCP)
might fail, since currently the driver doesn't wait for these operations to
actually take place.
This patch prevents the driver from moving forward before the operations
are reflected in the state register.
Signed-off-by: Tomer Tayar <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/qlogic/qed/qed_mcp.c | 46 ++++++++++++++++++++-----
drivers/net/ethernet/qlogic/qed/qed_reg_addr.h | 1
2 files changed, 39 insertions(+), 8 deletions(-)
--- a/drivers/net/ethernet/qlogic/qed/qed_mcp.c
+++ b/drivers/net/ethernet/qlogic/qed/qed_mcp.c
@@ -1998,31 +1998,61 @@ qed_mcp_send_drv_version(struct qed_hwfn
return rc;
}
+/* A maximal 100 msec waiting time for the MCP to halt */
+#define QED_MCP_HALT_SLEEP_MS 10
+#define QED_MCP_HALT_MAX_RETRIES 10
+
int qed_mcp_halt(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt)
{
- u32 resp = 0, param = 0;
+ u32 resp = 0, param = 0, cpu_state, cnt = 0;
int rc;
rc = qed_mcp_cmd(p_hwfn, p_ptt, DRV_MSG_CODE_MCP_HALT, 0, &resp,
¶m);
- if (rc)
+ if (rc) {
DP_ERR(p_hwfn, "MCP response failure, aborting\n");
+ return rc;
+ }
- return rc;
+ do {
+ msleep(QED_MCP_HALT_SLEEP_MS);
+ cpu_state = qed_rd(p_hwfn, p_ptt, MCP_REG_CPU_STATE);
+ if (cpu_state & MCP_REG_CPU_STATE_SOFT_HALTED)
+ break;
+ } while (++cnt < QED_MCP_HALT_MAX_RETRIES);
+
+ if (cnt == QED_MCP_HALT_MAX_RETRIES) {
+ DP_NOTICE(p_hwfn,
+ "Failed to halt the MCP [CPU_MODE = 0x%08x, CPU_STATE = 0x%08x]\n",
+ qed_rd(p_hwfn, p_ptt, MCP_REG_CPU_MODE), cpu_state);
+ return -EBUSY;
+ }
+
+ return 0;
}
+#define QED_MCP_RESUME_SLEEP_MS 10
+
int qed_mcp_resume(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt)
{
- u32 value, cpu_mode;
+ u32 cpu_mode, cpu_state;
qed_wr(p_hwfn, p_ptt, MCP_REG_CPU_STATE, 0xffffffff);
- value = qed_rd(p_hwfn, p_ptt, MCP_REG_CPU_MODE);
- value &= ~MCP_REG_CPU_MODE_SOFT_HALT;
- qed_wr(p_hwfn, p_ptt, MCP_REG_CPU_MODE, value);
cpu_mode = qed_rd(p_hwfn, p_ptt, MCP_REG_CPU_MODE);
+ cpu_mode &= ~MCP_REG_CPU_MODE_SOFT_HALT;
+ qed_wr(p_hwfn, p_ptt, MCP_REG_CPU_MODE, cpu_mode);
+ msleep(QED_MCP_RESUME_SLEEP_MS);
+ cpu_state = qed_rd(p_hwfn, p_ptt, MCP_REG_CPU_STATE);
+
+ if (cpu_state & MCP_REG_CPU_STATE_SOFT_HALTED) {
+ DP_NOTICE(p_hwfn,
+ "Failed to resume the MCP [CPU_MODE = 0x%08x, CPU_STATE = 0x%08x]\n",
+ cpu_mode, cpu_state);
+ return -EBUSY;
+ }
- return (cpu_mode & MCP_REG_CPU_MODE_SOFT_HALT) ? -EAGAIN : 0;
+ return 0;
}
int qed_mcp_ov_update_current_config(struct qed_hwfn *p_hwfn,
--- a/drivers/net/ethernet/qlogic/qed/qed_reg_addr.h
+++ b/drivers/net/ethernet/qlogic/qed/qed_reg_addr.h
@@ -554,6 +554,7 @@
0
#define MCP_REG_CPU_STATE \
0xe05004UL
+#define MCP_REG_CPU_STATE_SOFT_HALTED (0x1UL << 10)
#define MCP_REG_CPU_EVENT_MASK \
0xe05008UL
#define PGLUE_B_REG_PF_BAR0_SIZE \
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Alexey Dobriyan <[email protected]>
commit e5d9998f3e09359b372a037a6ac55ba235d95d57 upstream.
/*
* cpu_partial determined the maximum number of objects
* kept in the per cpu partial lists of a processor.
*/
Can't be negative.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Alexey Dobriyan <[email protected]>
Acked-by: Christoph Lameter <[email protected]>
Cc: Pekka Enberg <[email protected]>
Cc: David Rientjes <[email protected]>
Cc: Joonsoo Kim <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Signed-off-by: zhong jiang <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
include/linux/slub_def.h | 3 ++-
mm/slub.c | 6 +++---
2 files changed, 5 insertions(+), 4 deletions(-)
--- a/include/linux/slub_def.h
+++ b/include/linux/slub_def.h
@@ -88,7 +88,8 @@ struct kmem_cache {
int object_size; /* The size of an object without meta data */
int offset; /* Free pointer offset. */
#ifdef CONFIG_SLUB_CPU_PARTIAL
- int cpu_partial; /* Number of per cpu partial objects to keep around */
+ /* Number of per cpu partial objects to keep around */
+ unsigned int cpu_partial;
#endif
struct kmem_cache_order_objects oo;
--- a/mm/slub.c
+++ b/mm/slub.c
@@ -1807,7 +1807,7 @@ static void *get_partial_node(struct kme
{
struct page *page, *page2;
void *object = NULL;
- int available = 0;
+ unsigned int available = 0;
int objects;
/*
@@ -4942,10 +4942,10 @@ static ssize_t cpu_partial_show(struct k
static ssize_t cpu_partial_store(struct kmem_cache *s, const char *buf,
size_t length)
{
- unsigned long objects;
+ unsigned int objects;
int err;
- err = kstrtoul(buf, 10, &objects);
+ err = kstrtouint(buf, 10, &objects);
if (err)
return err;
if (objects && !kmem_cache_has_cpu_partial(s))
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Bo Chen <[email protected]>
[ Upstream commit ee400a3f1bfe7004a3e14b81c38ccc5583c26295 ]
In 'e1000_set_ringparam()', the tx_ring and rx_ring are updated with new value
and the old tx/rx rings are freed only when the device is up. There are resource
leaks on old tx/rx rings when the device is not up. This bug is reported by COD,
a tool for testing kernel module binaries I am building.
This patch fixes the bug by always calling 'kfree()' on old tx/rx rings in
'e1000_set_ringparam()'.
Signed-off-by: Bo Chen <[email protected]>
Reviewed-by: Alexander Duyck <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/intel/e1000/e1000_ethtool.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c
+++ b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c
@@ -644,14 +644,14 @@ static int e1000_set_ringparam(struct ne
adapter->tx_ring = tx_old;
e1000_free_all_rx_resources(adapter);
e1000_free_all_tx_resources(adapter);
- kfree(tx_old);
- kfree(rx_old);
adapter->rx_ring = rxdr;
adapter->tx_ring = txdr;
err = e1000_up(adapter);
if (err)
goto err_setup;
}
+ kfree(tx_old);
+ kfree(rx_old);
clear_bit(__E1000_RESETTING, &adapter->flags);
return 0;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Huazhong Tan <[email protected]>
[ Upstream commit 3ed614dce3ca9912d22be215ff0f11104b69fe62 ]
When enable the config item "CONFIG_ARM64_64K_PAGES", the size of PAGE_SIZE
is 65536(64K). But the type of length and page_offset are u16, they will
overflow. So change them to u32.
Fixes: 6fe6611ff275 ("net: add Hisilicon Network Subsystem hnae framework support")
Signed-off-by: Huazhong Tan <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/hisilicon/hns/hnae.h | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
--- a/drivers/net/ethernet/hisilicon/hns/hnae.h
+++ b/drivers/net/ethernet/hisilicon/hns/hnae.h
@@ -220,10 +220,10 @@ struct hnae_desc_cb {
/* priv data for the desc, e.g. skb when use with ip stack*/
void *priv;
- u16 page_offset;
- u16 reuse_flag;
+ u32 page_offset;
+ u32 length; /* length of the buffer */
- u16 length; /* length of the buffer */
+ u16 reuse_flag;
/* desc type, used by the ring user to mark the type of the priv data */
u16 type;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Rex Zhu <[email protected]>
[ Upstream commit 2ab4d0e74256fc49b7b270f63c1d1e47c2455abc ]
For SI/Kv, the power state is managed by function
amdgpu_pm_compute_clocks.
when dpm enabled, we should call amdgpu_pm_compute_clocks
to update current power state instand of set boot state.
this change can fix the oops when kfd driver was enabled on Kv.
Reviewed-by: Alex Deucher <[email protected]>
Tested-by: Michel Dänzer <[email protected]>
Signed-off-by: Rex Zhu <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/gpu/drm/amd/amdgpu/kv_dpm.c | 4 +---
drivers/gpu/drm/amd/amdgpu/si_dpm.c | 3 +--
2 files changed, 2 insertions(+), 5 deletions(-)
--- a/drivers/gpu/drm/amd/amdgpu/kv_dpm.c
+++ b/drivers/gpu/drm/amd/amdgpu/kv_dpm.c
@@ -1352,8 +1352,6 @@ static int kv_dpm_enable(struct amdgpu_d
return ret;
}
- kv_update_current_ps(adev, adev->pm.dpm.boot_ps);
-
if (adev->irq.installed &&
amdgpu_is_internal_thermal_sensor(adev->pm.int_thermal_type)) {
ret = kv_set_thermal_temperature_range(adev, KV_TEMP_RANGE_MIN, KV_TEMP_RANGE_MAX);
@@ -3054,7 +3052,7 @@ static int kv_dpm_hw_init(void *handle)
else
adev->pm.dpm_enabled = true;
mutex_unlock(&adev->pm.mutex);
-
+ amdgpu_pm_compute_clocks(adev);
return ret;
}
--- a/drivers/gpu/drm/amd/amdgpu/si_dpm.c
+++ b/drivers/gpu/drm/amd/amdgpu/si_dpm.c
@@ -6884,7 +6884,6 @@ static int si_dpm_enable(struct amdgpu_d
si_enable_auto_throttle_source(adev, AMDGPU_DPM_AUTO_THROTTLE_SRC_THERMAL, true);
si_thermal_start_thermal_controller(adev);
- ni_update_current_ps(adev, boot_ps);
return 0;
}
@@ -7758,7 +7757,7 @@ static int si_dpm_hw_init(void *handle)
else
adev->pm.dpm_enabled = true;
mutex_unlock(&adev->pm.mutex);
-
+ amdgpu_pm_compute_clocks(adev);
return ret;
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Niklas Cassel <[email protected]>
[ Upstream commit 3f04950f32d5d592ab4fcaecac2178558a6f7437 ]
When running iperf on ath10k SDIO, TX can stop working:
iperf -c 192.168.1.1 -i 1 -t 20 -w 10K
[ 3] 0.0- 1.0 sec 2.00 MBytes 16.8 Mbits/sec
[ 3] 1.0- 2.0 sec 3.12 MBytes 26.2 Mbits/sec
[ 3] 2.0- 3.0 sec 3.25 MBytes 27.3 Mbits/sec
[ 3] 3.0- 4.0 sec 655 KBytes 5.36 Mbits/sec
[ 3] 4.0- 5.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 5.0- 6.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 6.0- 7.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 7.0- 8.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 8.0- 9.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 9.0-10.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 0.0-10.3 sec 9.01 MBytes 7.32 Mbits/sec
There are frames in the ieee80211_txq and there are frames that have
been removed from from this queue, but haven't yet been sent on the wire
(num_pending_tx).
When num_pending_tx reaches max_num_pending_tx, we will stop the queues
by calling ieee80211_stop_queues().
As frames that have previously been sent for transmission
(num_pending_tx) are completed, we will decrease num_pending_tx and wake
the queues by calling ieee80211_wake_queue(). ieee80211_wake_queue()
does not call wake_tx_queue, so we might still have frames in the
queue at this point.
While the queues were stopped, the socket buffer might have filled up,
and in order for user space to write more, we need to free the frames
in the queue, since they are accounted to the socket. In order to free
them, we first need to transmit them.
This problem cannot be reproduced on low-latency devices, e.g. pci,
since they call ath10k_mac_tx_push_pending() from
ath10k_htt_txrx_compl_task(). ath10k_htt_txrx_compl_task() is not called
on high-latency devices.
Fix the problem by calling ath10k_mac_tx_push_pending(), after
processing rx packets, just like for low-latency devices, also in the
SDIO case. Since we are calling ath10k_mac_tx_push_pending() directly,
we also need to export it.
Signed-off-by: Niklas Cassel <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/wireless/ath/ath10k/mac.c | 1 +
drivers/net/wireless/ath/ath10k/sdio.c | 3 +++
2 files changed, 4 insertions(+)
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -4015,6 +4015,7 @@ void ath10k_mac_tx_push_pending(struct a
rcu_read_unlock();
spin_unlock_bh(&ar->txqs_lock);
}
+EXPORT_SYMBOL(ath10k_mac_tx_push_pending);
/************/
/* Scanning */
--- a/drivers/net/wireless/ath/ath10k/sdio.c
+++ b/drivers/net/wireless/ath/ath10k/sdio.c
@@ -30,6 +30,7 @@
#include "debug.h"
#include "hif.h"
#include "htc.h"
+#include "mac.h"
#include "targaddrs.h"
#include "trace.h"
#include "sdio.h"
@@ -1346,6 +1347,8 @@ static void ath10k_sdio_irq_handler(stru
break;
} while (time_before(jiffies, timeout) && !done);
+ ath10k_mac_tx_push_pending(ar);
+
sdio_claim_host(ar_sdio->func);
if (ret && ret != -ECANCELED)
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Chris Wilson <[email protected]>
commit 010e3e68cd9cb65ea50c0af605e966cda333cb2a upstream.
Originally we translated from the object to the vma by walking
obj->vma_list to find the matching vm (for user lookups). Now we process
user lookups using the rbtree, and we only use obj->vma_list itself for
maintaining state (e.g. ensuring that all vma are flushed or rebound).
As such maintenance needs to go on beyond the user's awareness of the
vma, defer removal of the vma from the obj->vma_list from i915_vma_close()
to i915_vma_destroy()
Fixes: 5888fc9eac3c ("drm/i915: Flush pending GTT writes before unbinding")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104155
Signed-off-by: Chris Wilson <[email protected]>
Cc: Joonas Lahtinen <[email protected]>
Cc: Tvrtko Ursulin <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Joonas Lahtinen <[email protected]>
Cc: Jani Nikula <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/gpu/drm/i915/i915_gem.c | 3 ++-
drivers/gpu/drm/i915/i915_vma.c | 4 +++-
2 files changed, 5 insertions(+), 2 deletions(-)
--- a/drivers/gpu/drm/i915/i915_gem.c
+++ b/drivers/gpu/drm/i915/i915_gem.c
@@ -3608,7 +3608,8 @@ restart:
return -EBUSY;
}
- if (i915_gem_valid_gtt_space(vma, cache_level))
+ if (!i915_vma_is_closed(vma) &&
+ i915_gem_valid_gtt_space(vma, cache_level))
continue;
ret = i915_vma_unbind(vma);
--- a/drivers/gpu/drm/i915/i915_vma.c
+++ b/drivers/gpu/drm/i915/i915_vma.c
@@ -430,6 +430,7 @@ i915_vma_insert(struct i915_vma *vma, u6
u64 start, end;
int ret;
+ GEM_BUG_ON(i915_vma_is_closed(vma));
GEM_BUG_ON(vma->flags & (I915_VMA_GLOBAL_BIND | I915_VMA_LOCAL_BIND));
GEM_BUG_ON(drm_mm_node_allocated(&vma->node));
@@ -590,7 +591,9 @@ static void i915_vma_destroy(struct i915
GEM_BUG_ON(i915_gem_active_isset(&vma->last_read[i]));
GEM_BUG_ON(i915_gem_active_isset(&vma->last_fence));
+ list_del(&vma->obj_link);
list_del(&vma->vm_link);
+
if (!i915_vma_is_ggtt(vma))
i915_ppgtt_put(i915_vm_to_ppgtt(vma->vm));
@@ -602,7 +605,6 @@ void i915_vma_close(struct i915_vma *vma
GEM_BUG_ON(i915_vma_is_closed(vma));
vma->flags |= I915_VMA_CLOSED;
- list_del(&vma->obj_link);
rb_erase(&vma->obj_node, &vma->obj->vma_tree);
if (!i915_vma_is_active(vma) && !i915_vma_is_pinned(vma))
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Dave Martin <[email protected]>
commit d26c25a9d19b5976b319af528886f89cf455692d upstream.
We currently allow userspace to access the core register file
in about any possible way, including straddling multiple
registers and doing unaligned accesses.
This is not the expected use of the ABI, and nobody is actually
using it that way. Let's tighten it by explicitly checking
the size and alignment for each field of the register file.
Cc: <[email protected]>
Fixes: 2f4a07c5f9fe ("arm64: KVM: guest one-reg interface")
Reviewed-by: Christoffer Dall <[email protected]>
Reviewed-by: Mark Rutland <[email protected]>
Signed-off-by: Dave Martin <[email protected]>
[maz: rewrote Dave's initial patch to be more easily backported]
Signed-off-by: Marc Zyngier <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/arm64/kvm/guest.c | 45 +++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 45 insertions(+)
--- a/arch/arm64/kvm/guest.c
+++ b/arch/arm64/kvm/guest.c
@@ -57,6 +57,45 @@ static u64 core_reg_offset_from_id(u64 i
return id & ~(KVM_REG_ARCH_MASK | KVM_REG_SIZE_MASK | KVM_REG_ARM_CORE);
}
+static int validate_core_offset(const struct kvm_one_reg *reg)
+{
+ u64 off = core_reg_offset_from_id(reg->id);
+ int size;
+
+ switch (off) {
+ case KVM_REG_ARM_CORE_REG(regs.regs[0]) ...
+ KVM_REG_ARM_CORE_REG(regs.regs[30]):
+ case KVM_REG_ARM_CORE_REG(regs.sp):
+ case KVM_REG_ARM_CORE_REG(regs.pc):
+ case KVM_REG_ARM_CORE_REG(regs.pstate):
+ case KVM_REG_ARM_CORE_REG(sp_el1):
+ case KVM_REG_ARM_CORE_REG(elr_el1):
+ case KVM_REG_ARM_CORE_REG(spsr[0]) ...
+ KVM_REG_ARM_CORE_REG(spsr[KVM_NR_SPSR - 1]):
+ size = sizeof(__u64);
+ break;
+
+ case KVM_REG_ARM_CORE_REG(fp_regs.vregs[0]) ...
+ KVM_REG_ARM_CORE_REG(fp_regs.vregs[31]):
+ size = sizeof(__uint128_t);
+ break;
+
+ case KVM_REG_ARM_CORE_REG(fp_regs.fpsr):
+ case KVM_REG_ARM_CORE_REG(fp_regs.fpcr):
+ size = sizeof(__u32);
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ if (KVM_REG_SIZE(reg->id) == size &&
+ IS_ALIGNED(off, size / sizeof(__u32)))
+ return 0;
+
+ return -EINVAL;
+}
+
static int get_core_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg)
{
/*
@@ -76,6 +115,9 @@ static int get_core_reg(struct kvm_vcpu
(off + (KVM_REG_SIZE(reg->id) / sizeof(__u32))) >= nr_regs)
return -ENOENT;
+ if (validate_core_offset(reg))
+ return -EINVAL;
+
if (copy_to_user(uaddr, ((u32 *)regs) + off, KVM_REG_SIZE(reg->id)))
return -EFAULT;
@@ -98,6 +140,9 @@ static int set_core_reg(struct kvm_vcpu
(off + (KVM_REG_SIZE(reg->id) / sizeof(__u32))) >= nr_regs)
return -ENOENT;
+ if (validate_core_offset(reg))
+ return -EINVAL;
+
if (KVM_REG_SIZE(reg->id) > sizeof(tmp))
return -EINVAL;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Alan Stern <[email protected]>
commit c9a4cb204e9eb7fa7dfbe3f7d3a674fa530aa193 upstream.
usb_find_alt_setting() takes a pointer to a struct usb_host_config as
an argument; it searches for an interface with specified interface and
alternate setting numbers in that config. However, it crashes if the
usb_host_config pointer argument is NULL.
Since this is a general-purpose routine, available for use in many
places, we want to to be more robust. This patch makes it return NULL
whenever the config argument is NULL.
Signed-off-by: Alan Stern <[email protected]>
Reported-by: [email protected]
CC: <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/core/usb.c | 2 ++
1 file changed, 2 insertions(+)
--- a/drivers/usb/core/usb.c
+++ b/drivers/usb/core/usb.c
@@ -228,6 +228,8 @@ struct usb_host_interface *usb_find_alt_
struct usb_interface_cache *intf_cache = NULL;
int i;
+ if (!config)
+ return NULL;
for (i = 0; i < config->desc.bNumInterfaces; i++) {
if (config->intf_cache[i]->altsetting[0].desc.bInterfaceNumber
== iface_num) {
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Aaron Ma <[email protected]>
commit 91a97507323e1ad4bfc10f4a5922e67cdaf8b3cd upstream.
Adding 2 new touchpad IDs to support middle button support.
Cc: [email protected]
Signed-off-by: Aaron Ma <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/input/mouse/elantech.c | 2 ++
1 file changed, 2 insertions(+)
--- a/drivers/input/mouse/elantech.c
+++ b/drivers/input/mouse/elantech.c
@@ -1180,6 +1180,8 @@ static const struct dmi_system_id elante
static const char * const middle_button_pnp_ids[] = {
"LEN2131", /* ThinkPad P52 w/ NFC */
"LEN2132", /* ThinkPad P52 */
+ "LEN2133", /* ThinkPad P72 w/ NFC */
+ "LEN2134", /* ThinkPad P72 */
NULL
};
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Alan Stern <[email protected]>
commit c183813fcee44a249339b7c46e1ad271ca1870aa upstream.
usb_driver_claim_interface() disables and re-enables Link Power
Management, but it shouldn't do either one, for the reasons listed
below. This patch removes the two LPM-related function calls from the
routine.
The reason for disabling LPM in the analogous function
usb_probe_interface() is so that drivers won't have to deal with
unwanted LPM transitions in their probe routine. But
usb_driver_claim_interface() doesn't call the driver's probe routine
(or any other callbacks), so that reason doesn't apply here.
Furthermore, no driver other than usbfs will ever call
usb_driver_claim_interface() unless it is already bound to another
interface in the same device, which means disabling LPM here would be
redundant. usbfs doesn't interact with LPM at all.
Lastly, the error return from usb_unlocked_disable_lpm() isn't handled
properly; the code doesn't clean up its earlier actions before
returning.
Signed-off-by: Alan Stern <[email protected]>
Fixes: 8306095fd2c1 ("USB: Disable USB 3.0 LPM in critical sections.")
CC: <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/core/driver.c | 15 ---------------
1 file changed, 15 deletions(-)
--- a/drivers/usb/core/driver.c
+++ b/drivers/usb/core/driver.c
@@ -512,7 +512,6 @@ int usb_driver_claim_interface(struct us
struct device *dev;
struct usb_device *udev;
int retval = 0;
- int lpm_disable_error = -ENODEV;
if (!iface)
return -ENODEV;
@@ -533,16 +532,6 @@ int usb_driver_claim_interface(struct us
iface->condition = USB_INTERFACE_BOUND;
- /* See the comment about disabling LPM in usb_probe_interface(). */
- if (driver->disable_hub_initiated_lpm) {
- lpm_disable_error = usb_unlocked_disable_lpm(udev);
- if (lpm_disable_error) {
- dev_err(&iface->dev, "%s Failed to disable LPM for driver %s\n.",
- __func__, driver->name);
- return -ENOMEM;
- }
- }
-
/* Claimed interfaces are initially inactive (suspended) and
* runtime-PM-enabled, but only if the driver has autosuspend
* support. Otherwise they are marked active, to prevent the
@@ -561,10 +550,6 @@ int usb_driver_claim_interface(struct us
if (device_is_registered(dev))
retval = device_bind_driver(dev);
- /* Attempt to re-enable USB3 LPM, if the disable was successful. */
- if (!lpm_disable_error)
- usb_unlocked_enable_lpm(udev);
-
if (retval) {
dev->driver = NULL;
usb_set_intfdata(iface, NULL);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Sebastian Andrzej Siewior <[email protected]>
commit e871db8d78df1c411032cbb3acfdf8930509360e upstream.
This reverts commit 6e22e3af7bb3a7b9dc53cb4687659f6e63fca427.
The bug the patch describes to, has been already fixed in commit
2df6948428542 ("USB: cdc-wdm: don't enable interrupts in USB-giveback")
so need to this, revert it.
Fixes: 6e22e3af7bb3 ("usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()")
Cc: stable <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/class/cdc-wdm.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/usb/class/cdc-wdm.c
+++ b/drivers/usb/class/cdc-wdm.c
@@ -457,7 +457,7 @@ static int service_outstanding_interrupt
set_bit(WDM_RESPONDING, &desc->flags);
spin_unlock_irq(&desc->iuspin);
- rv = usb_submit_urb(desc->response, GFP_ATOMIC);
+ rv = usb_submit_urb(desc->response, GFP_KERNEL);
spin_lock_irq(&desc->iuspin);
if (rv) {
dev_err(&desc->intf->dev,
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Oliver Neukum <[email protected]>
commit 7a68d9fb851012829c29e770621905529bd9490b upstream.
Requesting a ZERO_PACKET or not is sensible only for output.
In the input direction the device decides.
Likewise accepting short packets makes sense only for input.
This allows operation with panic_on_warn without opening up
a local DOS.
Signed-off-by: Oliver Neukum <[email protected]>
Reported-by: [email protected]
Fixes: 0cb54a3e47cb ("USB: debugging code shouldn't alter control flow")
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/core/devio.c | 19 ++++++++++++++++---
1 file changed, 16 insertions(+), 3 deletions(-)
--- a/drivers/usb/core/devio.c
+++ b/drivers/usb/core/devio.c
@@ -1451,10 +1451,13 @@ static int proc_do_submiturb(struct usb_
struct async *as = NULL;
struct usb_ctrlrequest *dr = NULL;
unsigned int u, totlen, isofrmlen;
- int i, ret, is_in, num_sgs = 0, ifnum = -1;
+ int i, ret, num_sgs = 0, ifnum = -1;
int number_of_packets = 0;
unsigned int stream_id = 0;
void *buf;
+ bool is_in;
+ bool allow_short = false;
+ bool allow_zero = false;
unsigned long mask = USBDEVFS_URB_SHORT_NOT_OK |
USBDEVFS_URB_BULK_CONTINUATION |
USBDEVFS_URB_NO_FSBR |
@@ -1488,6 +1491,8 @@ static int proc_do_submiturb(struct usb_
u = 0;
switch (uurb->type) {
case USBDEVFS_URB_TYPE_CONTROL:
+ if (is_in)
+ allow_short = true;
if (!usb_endpoint_xfer_control(&ep->desc))
return -EINVAL;
/* min 8 byte setup packet */
@@ -1528,6 +1533,10 @@ static int proc_do_submiturb(struct usb_
break;
case USBDEVFS_URB_TYPE_BULK:
+ if (!is_in)
+ allow_zero = true;
+ else
+ allow_short = true;
switch (usb_endpoint_type(&ep->desc)) {
case USB_ENDPOINT_XFER_CONTROL:
case USB_ENDPOINT_XFER_ISOC:
@@ -1548,6 +1557,10 @@ static int proc_do_submiturb(struct usb_
if (!usb_endpoint_xfer_int(&ep->desc))
return -EINVAL;
interrupt_urb:
+ if (!is_in)
+ allow_zero = true;
+ else
+ allow_short = true;
break;
case USBDEVFS_URB_TYPE_ISO:
@@ -1692,11 +1705,11 @@ static int proc_do_submiturb(struct usb_
u = (is_in ? URB_DIR_IN : URB_DIR_OUT);
if (uurb->flags & USBDEVFS_URB_ISO_ASAP)
u |= URB_ISO_ASAP;
- if (uurb->flags & USBDEVFS_URB_SHORT_NOT_OK && is_in)
+ if (allow_short && uurb->flags & USBDEVFS_URB_SHORT_NOT_OK)
u |= URB_SHORT_NOT_OK;
if (uurb->flags & USBDEVFS_URB_NO_FSBR)
u |= URB_NO_FSBR;
- if (uurb->flags & USBDEVFS_URB_ZERO_PACKET)
+ if (allow_zero && uurb->flags & USBDEVFS_URB_ZERO_PACKET)
u |= URB_ZERO_PACKET;
if (uurb->flags & USBDEVFS_URB_NO_INTERRUPT)
u |= URB_NO_INTERRUPT;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Tony Lindgren <[email protected]>
[ Upstream commit 2d59bb602314a4b2593fde267734266b5e872dd0 ]
Otherwise we can get the following errors occasionally on some devices:
mmc1: tried to HW reset card, got error -110
mmcblk1: error -110 requesting status
mmcblk1: recovery failed!
print_req_error: I/O error, dev mmcblk1, sector 14329
...
I have one device that hits this error almost on every boot, and another
one that hits it only rarely with the other ones I've used behave without
problems. I'm not sure if the issue is related to a particular eMMC card
model, but in case it is, both of the machines with issues have:
# cat /sys/class/mmc_host/mmc1/mmc1:0001/manfid \
/sys/class/mmc_host/mmc1/mmc1:0001/oemid \
/sys/class/mmc_host/mmc1/mmc1:0001/name
0x000045
0x0100
SEM16G
and the working ones have:
0x000011
0x0100
016G92
Note that "ti,non-removable" is different as omap_hsmmc_reg_get() does not
call omap_hsmmc_disable_boot_regulators() if no_regulator_off_init is set.
And currently we set no_regulator_off_init only for "ti,non-removable" and
not for "non-removable". It seems that we should have "non-removable" with
some other mmc generic property behave in the same way instead of having to
use a non-generic property. But let's fix the issue first.
Fixes: 7e2f8c0ae670 ("ARM: dts: Add minimal support for motorola droid 4
xt894")
Cc: Marcel Partap <[email protected]>
Cc: Merlijn Wajer <[email protected]>
Cc: Michael Scott <[email protected]>
Cc: NeKit <[email protected]>
Cc: Pavel Machek <[email protected]>
Cc: Sebastian Reichel <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/arm/boot/dts/omap4-droid4-xt894.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/arch/arm/boot/dts/omap4-droid4-xt894.dts
+++ b/arch/arm/boot/dts/omap4-droid4-xt894.dts
@@ -314,7 +314,7 @@
&mmc2 {
vmmc-supply = <&vsdio>;
bus-width = <8>;
- non-removable;
+ ti,non-removable;
};
&mmc3 {
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Linus Walleij <[email protected]>
[ Upstream commit 46cb52ad414ac829680d0bb8cc7090ac2b577ca7 ]
The DMA is broken on this specific device for some unknown
reason (probably badly designed or plain broken interface
electronics) and will only work with PIO. Other users of
the same hardware does not have this problem.
Add a specific quirk so that this Gemini device gets
DMA turned off. Also fix up some code around passing the
port information around in probe while we're at it.
Signed-off-by: Linus Walleij <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/ata/pata_ftide010.c | 27 +++++++++++++++++----------
1 file changed, 17 insertions(+), 10 deletions(-)
--- a/drivers/ata/pata_ftide010.c
+++ b/drivers/ata/pata_ftide010.c
@@ -256,14 +256,12 @@ static struct ata_port_operations pata_f
.qc_issue = ftide010_qc_issue,
};
-static struct ata_port_info ftide010_port_info[] = {
- {
- .flags = ATA_FLAG_SLAVE_POSS,
- .mwdma_mask = ATA_MWDMA2,
- .udma_mask = ATA_UDMA6,
- .pio_mask = ATA_PIO4,
- .port_ops = &pata_ftide010_port_ops,
- },
+static struct ata_port_info ftide010_port_info = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA6,
+ .pio_mask = ATA_PIO4,
+ .port_ops = &pata_ftide010_port_ops,
};
#if IS_ENABLED(CONFIG_SATA_GEMINI)
@@ -349,6 +347,7 @@ static int pata_ftide010_gemini_cable_de
}
static int pata_ftide010_gemini_init(struct ftide010 *ftide,
+ struct ata_port_info *pi,
bool is_ata1)
{
struct device *dev = ftide->dev;
@@ -373,7 +372,13 @@ static int pata_ftide010_gemini_init(str
/* Flag port as SATA-capable */
if (gemini_sata_bridge_enabled(sg, is_ata1))
- ftide010_port_info[0].flags |= ATA_FLAG_SATA;
+ pi->flags |= ATA_FLAG_SATA;
+
+ /* This device has broken DMA, only PIO works */
+ if (of_machine_is_compatible("itian,sq201")) {
+ pi->mwdma_mask = 0;
+ pi->udma_mask = 0;
+ }
/*
* We assume that a simple 40-wire cable is used in the PATA mode.
@@ -435,6 +440,7 @@ static int pata_ftide010_gemini_init(str
}
#else
static int pata_ftide010_gemini_init(struct ftide010 *ftide,
+ struct ata_port_info *pi,
bool is_ata1)
{
return -ENOTSUPP;
@@ -446,7 +452,7 @@ static int pata_ftide010_probe(struct pl
{
struct device *dev = &pdev->dev;
struct device_node *np = dev->of_node;
- const struct ata_port_info pi = ftide010_port_info[0];
+ struct ata_port_info pi = ftide010_port_info;
const struct ata_port_info *ppi[] = { &pi, NULL };
struct ftide010 *ftide;
struct resource *res;
@@ -490,6 +496,7 @@ static int pata_ftide010_probe(struct pl
* are ATA0. This will also set up the cable types.
*/
ret = pata_ftide010_gemini_init(ftide,
+ &pi,
(res->start == 0x63400000));
if (ret)
goto err_dis_clk;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Marc Zyngier <[email protected]>
[ Upstream commit 1d8f574708a3fb6f18c85486d0c5217df893c0cf ]
An unfortunate consequence of having a strong typing for the input
values to the SMC call is that it also affects the type of the
return values, limiting r0 to 32 bits and r{1,2,3} to whatever
was passed as an input.
Let's turn everything into "unsigned long", which satisfies the
requirements of both architectures, and allows for the full
range of return values.
Reported-by: Julien Grall <[email protected]>
Signed-off-by: Marc Zyngier <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
include/linux/arm-smccc.h | 20 ++++++++++----------
1 file changed, 10 insertions(+), 10 deletions(-)
--- a/include/linux/arm-smccc.h
+++ b/include/linux/arm-smccc.h
@@ -199,31 +199,31 @@ asmlinkage void __arm_smccc_hvc(unsigned
#define __declare_arg_0(a0, res) \
struct arm_smccc_res *___res = res; \
- register u32 r0 asm("r0") = a0; \
+ register unsigned long r0 asm("r0") = (u32)a0; \
register unsigned long r1 asm("r1"); \
register unsigned long r2 asm("r2"); \
register unsigned long r3 asm("r3")
#define __declare_arg_1(a0, a1, res) \
struct arm_smccc_res *___res = res; \
- register u32 r0 asm("r0") = a0; \
- register typeof(a1) r1 asm("r1") = a1; \
+ register unsigned long r0 asm("r0") = (u32)a0; \
+ register unsigned long r1 asm("r1") = a1; \
register unsigned long r2 asm("r2"); \
register unsigned long r3 asm("r3")
#define __declare_arg_2(a0, a1, a2, res) \
struct arm_smccc_res *___res = res; \
- register u32 r0 asm("r0") = a0; \
- register typeof(a1) r1 asm("r1") = a1; \
- register typeof(a2) r2 asm("r2") = a2; \
+ register unsigned long r0 asm("r0") = (u32)a0; \
+ register unsigned long r1 asm("r1") = a1; \
+ register unsigned long r2 asm("r2") = a2; \
register unsigned long r3 asm("r3")
#define __declare_arg_3(a0, a1, a2, a3, res) \
struct arm_smccc_res *___res = res; \
- register u32 r0 asm("r0") = a0; \
- register typeof(a1) r1 asm("r1") = a1; \
- register typeof(a2) r2 asm("r2") = a2; \
- register typeof(a3) r3 asm("r3") = a3
+ register unsigned long r0 asm("r0") = (u32)a0; \
+ register unsigned long r1 asm("r1") = a1; \
+ register unsigned long r2 asm("r2") = a2; \
+ register unsigned long r3 asm("r3") = a3
#define __declare_arg_4(a0, a1, a2, a3, a4, res) \
__declare_arg_3(a0, a1, a2, a3, res); \
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Rex Zhu <[email protected]>
[ Upstream commit 8ef23364b654d44244400d79988e677e504b21ba ]
This is required by gfx hw and can fix the rlc hang when
do s3 stree test on Cz/St.
Reviewed-by: Alex Deucher <[email protected]>
Signed-off-by: Hang Zhou <[email protected]>
Signed-off-by: Rex Zhu <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/gpu/drm/amd/amdgpu/gfx_v8_0.c | 11 ++++++++++-
1 file changed, 10 insertions(+), 1 deletion(-)
--- a/drivers/gpu/drm/amd/amdgpu/gfx_v8_0.c
+++ b/drivers/gpu/drm/amd/amdgpu/gfx_v8_0.c
@@ -5479,6 +5479,11 @@ static int gfx_v8_0_set_powergating_stat
if (amdgpu_sriov_vf(adev))
return 0;
+ if (adev->pg_flags & (AMD_PG_SUPPORT_GFX_SMG |
+ AMD_PG_SUPPORT_RLC_SMU_HS |
+ AMD_PG_SUPPORT_CP |
+ AMD_PG_SUPPORT_GFX_DMG))
+ adev->gfx.rlc.funcs->enter_safe_mode(adev);
switch (adev->asic_type) {
case CHIP_CARRIZO:
case CHIP_STONEY:
@@ -5527,7 +5532,11 @@ static int gfx_v8_0_set_powergating_stat
default:
break;
}
-
+ if (adev->pg_flags & (AMD_PG_SUPPORT_GFX_SMG |
+ AMD_PG_SUPPORT_RLC_SMU_HS |
+ AMD_PG_SUPPORT_CP |
+ AMD_PG_SUPPORT_GFX_DMG))
+ adev->gfx.rlc.funcs->exit_safe_mode(adev);
return 0;
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Leonard Crestez <[email protected]>
[ Upstream commit 538d6e9d597584e80514698e24321645debde78f ]
This reverts commit 1c86c9dd82f859b474474a7fee0d5195da2c9c1d.
That commit followed the reference manual but unfortunately the imx7d
manual is incorrect.
Tested with ath9k pcie card and confirmed internally.
Signed-off-by: Leonard Crestez <[email protected]>
Acked-by: Lucas Stach <[email protected]>
Fixes: 1c86c9dd82f8 ("ARM: dts: imx7d: Invert legacy PCI irq mapping")
Signed-off-by: Shawn Guo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/arm/boot/dts/imx7d.dtsi | 12 ++++++++----
1 file changed, 8 insertions(+), 4 deletions(-)
--- a/arch/arm/boot/dts/imx7d.dtsi
+++ b/arch/arm/boot/dts/imx7d.dtsi
@@ -144,10 +144,14 @@
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
- interrupt-map = <0 0 0 1 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
- <0 0 0 2 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
- <0 0 0 3 &intc GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
- <0 0 0 4 &intc GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ /*
+ * Reference manual lists pci irqs incorrectly
+ * Real hardware ordering is same as imx6: D+MSI, C, B, A
+ */
+ interrupt-map = <0 0 0 1 &intc GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 2 &intc GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 3 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 4 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX7D_PCIE_CTRL_ROOT_CLK>,
<&clks IMX7D_PLL_ENET_MAIN_100M_CLK>,
<&clks IMX7D_PCIE_PHY_ROOT_CLK>;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Randy Dunlap <[email protected]>
[ Upstream commit ff924c5a1ec7548825cc2d07980b03be4224ffac ]
Fix the section mismatch warning in arch/x86/mm/pti.c:
WARNING: vmlinux.o(.text+0x6972a): Section mismatch in reference from the function pti_clone_pgtable() to the function .init.text:pti_user_pagetable_walk_pte()
The function pti_clone_pgtable() references
the function __init pti_user_pagetable_walk_pte().
This is often because pti_clone_pgtable lacks a __init
annotation or the annotation of pti_user_pagetable_walk_pte is wrong.
FATAL: modpost: Section mismatches detected.
Fixes: 85900ea51577 ("x86/pti: Map the vsyscall page if needed")
Reported-by: kbuild test robot <[email protected]>
Signed-off-by: Randy Dunlap <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/x86/mm/pti.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/arch/x86/mm/pti.c
+++ b/arch/x86/mm/pti.c
@@ -224,7 +224,7 @@ static __init pmd_t *pti_user_pagetable_
*
* Returns a pointer to a PTE on success, or NULL on failure.
*/
-static __init pte_t *pti_user_pagetable_walk_pte(unsigned long address)
+static pte_t *pti_user_pagetable_walk_pte(unsigned long address)
{
gfp_t gfp = (GFP_KERNEL | __GFP_NOTRACK | __GFP_ZERO);
pmd_t *pmd;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Dan Carpenter <[email protected]>
[ Upstream commit f196dec6d50abb2e65fb54a0621b2f1b4d922995 ]
The adt7475_read_word() function was meant to return negative error
codes on failure.
Signed-off-by: Dan Carpenter <[email protected]>
Reviewed-by: Tokunori Ikegami <[email protected]>
Signed-off-by: Guenter Roeck <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/hwmon/adt7475.c | 14 +++++++++-----
1 file changed, 9 insertions(+), 5 deletions(-)
--- a/drivers/hwmon/adt7475.c
+++ b/drivers/hwmon/adt7475.c
@@ -303,14 +303,18 @@ static inline u16 volt2reg(int channel,
return clamp_val(reg, 0, 1023) & (0xff << 2);
}
-static u16 adt7475_read_word(struct i2c_client *client, int reg)
+static int adt7475_read_word(struct i2c_client *client, int reg)
{
- u16 val;
+ int val1, val2;
- val = i2c_smbus_read_byte_data(client, reg);
- val |= (i2c_smbus_read_byte_data(client, reg + 1) << 8);
+ val1 = i2c_smbus_read_byte_data(client, reg);
+ if (val1 < 0)
+ return val1;
+ val2 = i2c_smbus_read_byte_data(client, reg + 1);
+ if (val2 < 0)
+ return val2;
- return val;
+ return val1 | (val2 << 8);
}
static void adt7475_write_word(struct i2c_client *client, int reg, u16 val)
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Bart Van Assche <[email protected]>
commit ee92efe41cf358f4b99e73509f2bfd4733609f26 upstream.
Use different loop variables for the inner and outer loop. This avoids
that an infinite loop occurs if there are more RDMA channels than
target->req_ring_size.
Fixes: d92c0da71a35 ("IB/srp: Add multichannel support")
Cc: <[email protected]>
Signed-off-by: Bart Van Assche <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/infiniband/ulp/srp/ib_srp.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
--- a/drivers/infiniband/ulp/srp/ib_srp.c
+++ b/drivers/infiniband/ulp/srp/ib_srp.c
@@ -2669,7 +2669,7 @@ static int srp_reset_device(struct scsi_
{
struct srp_target_port *target = host_to_target(scmnd->device->host);
struct srp_rdma_ch *ch;
- int i;
+ int i, j;
u8 status;
shost_printk(KERN_ERR, target->scsi_host, "SRP reset_device called\n");
@@ -2683,8 +2683,8 @@ static int srp_reset_device(struct scsi_
for (i = 0; i < target->ch_count; i++) {
ch = &target->ch[i];
- for (i = 0; i < target->req_ring_size; ++i) {
- struct srp_request *req = &ch->req_ring[i];
+ for (j = 0; j < target->req_ring_size; ++j) {
+ struct srp_request *req = &ch->req_ring[j];
srp_finish_req(ch, req, scmnd->device, DID_RESET << 16);
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Lothar Felten <[email protected]>
[ Upstream commit 3ad867001c91657c46dcf6656d52eb6080286fd5 ]
fix the sysfs shunt resistor read access: return the shunt resistor
value, not the calibration register contents.
update email address
Signed-off-by: Lothar Felten <[email protected]>
Signed-off-by: Guenter Roeck <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
Documentation/hwmon/ina2xx | 2 +-
drivers/hwmon/ina2xx.c | 13 +++++++++++--
include/linux/platform_data/ina2xx.h | 2 +-
3 files changed, 13 insertions(+), 4 deletions(-)
--- a/Documentation/hwmon/ina2xx
+++ b/Documentation/hwmon/ina2xx
@@ -32,7 +32,7 @@ Supported chips:
Datasheet: Publicly available at the Texas Instruments website
http://www.ti.com/
-Author: Lothar Felten <[email protected]>
+Author: Lothar Felten <[email protected]>
Description
-----------
--- a/drivers/hwmon/ina2xx.c
+++ b/drivers/hwmon/ina2xx.c
@@ -17,7 +17,7 @@
* Bi-directional Current/Power Monitor with I2C Interface
* Datasheet: http://www.ti.com/product/ina230
*
- * Copyright (C) 2012 Lothar Felten <[email protected]>
+ * Copyright (C) 2012 Lothar Felten <[email protected]>
* Thanks to Jan Volkering
*
* This program is free software; you can redistribute it and/or modify
@@ -329,6 +329,15 @@ static int ina2xx_set_shunt(struct ina2x
return 0;
}
+static ssize_t ina2xx_show_shunt(struct device *dev,
+ struct device_attribute *da,
+ char *buf)
+{
+ struct ina2xx_data *data = dev_get_drvdata(dev);
+
+ return snprintf(buf, PAGE_SIZE, "%li\n", data->rshunt);
+}
+
static ssize_t ina2xx_store_shunt(struct device *dev,
struct device_attribute *da,
const char *buf, size_t count)
@@ -403,7 +412,7 @@ static SENSOR_DEVICE_ATTR(power1_input,
/* shunt resistance */
static SENSOR_DEVICE_ATTR(shunt_resistor, S_IRUGO | S_IWUSR,
- ina2xx_show_value, ina2xx_store_shunt,
+ ina2xx_show_shunt, ina2xx_store_shunt,
INA2XX_CALIBRATION);
/* update interval (ina226 only) */
--- a/include/linux/platform_data/ina2xx.h
+++ b/include/linux/platform_data/ina2xx.h
@@ -1,7 +1,7 @@
/*
* Driver for Texas Instruments INA219, INA226 power monitor chips
*
- * Copyright (C) 2012 Lothar Felten <[email protected]>
+ * Copyright (C) 2012 Lothar Felten <[email protected]>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Srikanth Jampala <[email protected]>
[ Upstream commit 3d7c82060d1fe65bde4023aac41a0b1bd7718e07 ]
Earlier used to post the current command without checking queue full
after backlog submissions. So, post the current command only after
confirming the space in queue after backlog submissions.
Maintain host write index instead of reading device registers
to get the next free slot to post the command.
Return -ENOSPC in queue full case.
Signed-off-by: Srikanth Jampala <[email protected]>
Reviewed-by: Gadam Sreerama <[email protected]>
Tested-by: Jha, Chandan <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/crypto/cavium/nitrox/nitrox_dev.h | 3 -
drivers/crypto/cavium/nitrox/nitrox_lib.c | 1
drivers/crypto/cavium/nitrox/nitrox_reqmgr.c | 57 +++++++++++++++------------
3 files changed, 35 insertions(+), 26 deletions(-)
--- a/drivers/crypto/cavium/nitrox/nitrox_dev.h
+++ b/drivers/crypto/cavium/nitrox/nitrox_dev.h
@@ -35,6 +35,7 @@ struct nitrox_cmdq {
/* requests in backlog queues */
atomic_t backlog_count;
+ int write_idx;
/* command size 32B/64B */
u8 instr_size;
u8 qno;
@@ -87,7 +88,7 @@ struct nitrox_bh {
struct bh_data *slc;
};
-/* NITROX-5 driver state */
+/* NITROX-V driver state */
#define NITROX_UCODE_LOADED 0
#define NITROX_READY 1
--- a/drivers/crypto/cavium/nitrox/nitrox_lib.c
+++ b/drivers/crypto/cavium/nitrox/nitrox_lib.c
@@ -36,6 +36,7 @@ static int cmdq_common_init(struct nitro
cmdq->head = PTR_ALIGN(cmdq->head_unaligned, PKT_IN_ALIGN);
cmdq->dma = PTR_ALIGN(cmdq->dma_unaligned, PKT_IN_ALIGN);
cmdq->qsize = (qsize + PKT_IN_ALIGN);
+ cmdq->write_idx = 0;
spin_lock_init(&cmdq->response_lock);
spin_lock_init(&cmdq->cmdq_lock);
--- a/drivers/crypto/cavium/nitrox/nitrox_reqmgr.c
+++ b/drivers/crypto/cavium/nitrox/nitrox_reqmgr.c
@@ -43,6 +43,16 @@
* Invalid flag options in AES-CCM IV.
*/
+static inline int incr_index(int index, int count, int max)
+{
+ if ((index + count) >= max)
+ index = index + count - max;
+ else
+ index += count;
+
+ return index;
+}
+
/**
* dma_free_sglist - unmap and free the sg lists.
* @ndev: N5 device
@@ -427,30 +437,29 @@ static void post_se_instr(struct nitrox_
struct nitrox_cmdq *cmdq)
{
struct nitrox_device *ndev = sr->ndev;
- union nps_pkt_in_instr_baoff_dbell pkt_in_baoff_dbell;
- u64 offset;
+ int idx;
u8 *ent;
spin_lock_bh(&cmdq->cmdq_lock);
- /* get the next write offset */
- offset = NPS_PKT_IN_INSTR_BAOFF_DBELLX(cmdq->qno);
- pkt_in_baoff_dbell.value = nitrox_read_csr(ndev, offset);
+ idx = cmdq->write_idx;
/* copy the instruction */
- ent = cmdq->head + pkt_in_baoff_dbell.s.aoff;
+ ent = cmdq->head + (idx * cmdq->instr_size);
memcpy(ent, &sr->instr, cmdq->instr_size);
- /* flush the command queue updates */
- dma_wmb();
- sr->tstamp = jiffies;
atomic_set(&sr->status, REQ_POSTED);
response_list_add(sr, cmdq);
+ sr->tstamp = jiffies;
+ /* flush the command queue updates */
+ dma_wmb();
/* Ring doorbell with count 1 */
writeq(1, cmdq->dbell_csr_addr);
/* orders the doorbell rings */
mmiowb();
+ cmdq->write_idx = incr_index(idx, 1, ndev->qlen);
+
spin_unlock_bh(&cmdq->cmdq_lock);
}
@@ -460,6 +469,9 @@ static int post_backlog_cmds(struct nitr
struct nitrox_softreq *sr, *tmp;
int ret = 0;
+ if (!atomic_read(&cmdq->backlog_count))
+ return 0;
+
spin_lock_bh(&cmdq->backlog_lock);
list_for_each_entry_safe(sr, tmp, &cmdq->backlog_head, backlog) {
@@ -467,7 +479,7 @@ static int post_backlog_cmds(struct nitr
/* submit until space available */
if (unlikely(cmdq_full(cmdq, ndev->qlen))) {
- ret = -EBUSY;
+ ret = -ENOSPC;
break;
}
/* delete from backlog list */
@@ -492,23 +504,20 @@ static int nitrox_enqueue_request(struct
{
struct nitrox_cmdq *cmdq = sr->cmdq;
struct nitrox_device *ndev = sr->ndev;
- int ret = -EBUSY;
+
+ /* try to post backlog requests */
+ post_backlog_cmds(cmdq);
if (unlikely(cmdq_full(cmdq, ndev->qlen))) {
if (!(sr->flags & CRYPTO_TFM_REQ_MAY_BACKLOG))
- return -EAGAIN;
-
+ return -ENOSPC;
+ /* add to backlog list */
backlog_list_add(sr, cmdq);
- } else {
- ret = post_backlog_cmds(cmdq);
- if (ret) {
- backlog_list_add(sr, cmdq);
- return ret;
- }
- post_se_instr(sr, cmdq);
- ret = -EINPROGRESS;
+ return -EBUSY;
}
- return ret;
+ post_se_instr(sr, cmdq);
+
+ return -EINPROGRESS;
}
/**
@@ -625,11 +634,9 @@ int nitrox_process_se_request(struct nit
*/
sr->instr.fdata[0] = *((u64 *)&req->gph);
sr->instr.fdata[1] = 0;
- /* flush the soft_req changes before posting the cmd */
- wmb();
ret = nitrox_enqueue_request(sr);
- if (ret == -EAGAIN)
+ if (ret == -ENOSPC)
goto send_fail;
return ret;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Oliver Neukum <[email protected]>
commit 81e0403b26d94360abd1f6a57311337973bc82cd upstream.
If we filter flags before they reach the core we need to generate our
own warnings.
Signed-off-by: Oliver Neukum <[email protected]>
Fixes: 0cb54a3e47cb ("USB: debugging code shouldn't alter control flow")
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/core/devio.c | 5 +++++
1 file changed, 5 insertions(+)
--- a/drivers/usb/core/devio.c
+++ b/drivers/usb/core/devio.c
@@ -1715,6 +1715,11 @@ static int proc_do_submiturb(struct usb_
u |= URB_NO_INTERRUPT;
as->urb->transfer_flags = u;
+ if (!allow_short && uurb->flags & USBDEVFS_URB_SHORT_NOT_OK)
+ dev_warn(&ps->dev->dev, "Requested nonsensical USBDEVFS_URB_SHORT_NOT_OK.\n");
+ if (!allow_zero && uurb->flags & USBDEVFS_URB_ZERO_PACKET)
+ dev_warn(&ps->dev->dev, "Requested nonsensical USBDEVFS_URB_ZERO_PACKET.\n");
+
as->urb->transfer_buffer_length = uurb->buffer_length;
as->urb->setup_packet = (unsigned char *)dr;
dr = NULL;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: ming_qian <[email protected]>
commit f620d1d7afc7db57ab59f35000752840c91f67e7 upstream.
media: uvcvideo: Support UVC 1.5 video probe & commit controls
The length of UVC 1.5 video control is 48, and it is 34 for UVC 1.1.
Change it to 48 for UVC 1.5 device, and the UVC 1.5 device can be
recognized.
More changes to the driver are needed for full UVC 1.5 compatibility.
However, at least the UVC 1.5 Realtek RTS5847/RTS5852 cameras have been
reported to work well.
[[email protected]: Factor out code to helper function, update size checks]
Cc: [email protected]
Signed-off-by: ming_qian <[email protected]>
Signed-off-by: Laurent Pinchart <[email protected]>
Tested-by: Kai-Heng Feng <[email protected]>
Tested-by: Ana Guerrero Lopez <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/media/usb/uvc/uvc_video.c | 24 ++++++++++++++++++------
1 file changed, 18 insertions(+), 6 deletions(-)
--- a/drivers/media/usb/uvc/uvc_video.c
+++ b/drivers/media/usb/uvc/uvc_video.c
@@ -163,14 +163,27 @@ static void uvc_fixup_video_ctrl(struct
}
}
+static size_t uvc_video_ctrl_size(struct uvc_streaming *stream)
+{
+ /*
+ * Return the size of the video probe and commit controls, which depends
+ * on the protocol version.
+ */
+ if (stream->dev->uvc_version < 0x0110)
+ return 26;
+ else if (stream->dev->uvc_version < 0x0150)
+ return 34;
+ else
+ return 48;
+}
+
static int uvc_get_video_ctrl(struct uvc_streaming *stream,
struct uvc_streaming_control *ctrl, int probe, __u8 query)
{
+ __u16 size = uvc_video_ctrl_size(stream);
__u8 *data;
- __u16 size;
int ret;
- size = stream->dev->uvc_version >= 0x0110 ? 34 : 26;
if ((stream->dev->quirks & UVC_QUIRK_PROBE_DEF) &&
query == UVC_GET_DEF)
return -EIO;
@@ -225,7 +238,7 @@ static int uvc_get_video_ctrl(struct uvc
ctrl->dwMaxVideoFrameSize = get_unaligned_le32(&data[18]);
ctrl->dwMaxPayloadTransferSize = get_unaligned_le32(&data[22]);
- if (size == 34) {
+ if (size >= 34) {
ctrl->dwClockFrequency = get_unaligned_le32(&data[26]);
ctrl->bmFramingInfo = data[30];
ctrl->bPreferedVersion = data[31];
@@ -254,11 +267,10 @@ out:
static int uvc_set_video_ctrl(struct uvc_streaming *stream,
struct uvc_streaming_control *ctrl, int probe)
{
+ __u16 size = uvc_video_ctrl_size(stream);
__u8 *data;
- __u16 size;
int ret;
- size = stream->dev->uvc_version >= 0x0110 ? 34 : 26;
data = kzalloc(size, GFP_KERNEL);
if (data == NULL)
return -ENOMEM;
@@ -275,7 +287,7 @@ static int uvc_set_video_ctrl(struct uvc
put_unaligned_le32(ctrl->dwMaxVideoFrameSize, &data[18]);
put_unaligned_le32(ctrl->dwMaxPayloadTransferSize, &data[22]);
- if (size == 34) {
+ if (size >= 34) {
put_unaligned_le32(ctrl->dwClockFrequency, &data[26]);
data[30] = ctrl->bmFramingInfo;
data[31] = ctrl->bPreferedVersion;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Mika Westerberg <[email protected]>
[ Upstream commit 7fd6d98b89f382d414e1db528e29a67bbd749457 ]
Commit 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict
with PCI BAR") made it possible for AML code to access SMBus I/O ports
by installing custom SystemIO OpRegion handler and blocking i80i driver
access upon first AML read/write to this OpRegion.
However, while ThinkPad T560 does have SystemIO OpRegion declared under
the SMBus device, it does not access any of the SMBus registers:
Device (SMBU)
{
...
OperationRegion (SMBP, PCI_Config, 0x50, 0x04)
Field (SMBP, DWordAcc, NoLock, Preserve)
{
, 5,
TCOB, 11,
Offset (0x04)
}
Name (TCBV, 0x00)
Method (TCBS, 0, NotSerialized)
{
If ((TCBV == 0x00))
{
TCBV = (\_SB.PCI0.SMBU.TCOB << 0x05)
}
Return (TCBV) /* \_SB_.PCI0.SMBU.TCBV */
}
OperationRegion (TCBA, SystemIO, TCBS (), 0x10)
Field (TCBA, ByteAcc, NoLock, Preserve)
{
Offset (0x04),
, 9,
CPSC, 1
}
}
Problem with the current approach is that it blocks all I/O port access
and because this system has touchpad connected to the SMBus controller
after first AML access (happens during suspend/resume cycle) the
touchpad fails to work anymore.
Fix this so that we allow ACPI AML I/O port access if it does not touch
the region reserved for the SMBus.
Fixes: 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200737
Reported-by: Yussuf Khalil <[email protected]>
Signed-off-by: Mika Westerberg <[email protected]>
Reviewed-by: Jean Delvare <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/i2c/busses/i2c-i801.c | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)
--- a/drivers/i2c/busses/i2c-i801.c
+++ b/drivers/i2c/busses/i2c-i801.c
@@ -1416,6 +1416,13 @@ static void i801_add_tco(struct i801_pri
}
#ifdef CONFIG_ACPI
+static bool i801_acpi_is_smbus_ioport(const struct i801_priv *priv,
+ acpi_physical_address address)
+{
+ return address >= priv->smba &&
+ address <= pci_resource_end(priv->pci_dev, SMBBAR);
+}
+
static acpi_status
i801_acpi_io_handler(u32 function, acpi_physical_address address, u32 bits,
u64 *value, void *handler_context, void *region_context)
@@ -1431,7 +1438,7 @@ i801_acpi_io_handler(u32 function, acpi_
*/
mutex_lock(&priv->acpi_lock);
- if (!priv->acpi_reserved) {
+ if (!priv->acpi_reserved && i801_acpi_is_smbus_ioport(priv, address)) {
priv->acpi_reserved = true;
dev_warn(&pdev->dev, "BIOS is accessing SMBus registers\n");
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Huazhong Tan <[email protected]>
[ Upstream commit b1ccd4c0ab6ef499f47dd84ed4920502a7147bba ]
skb->truesize is not meant to be tracking amount of used bytes in a skb,
but amount of reserved/consumed bytes in memory.
For instance, if we use a single byte in last page fragment, we have to
account the full size of the fragment.
So skb_add_rx_frag needs to calculate the length of the entire buffer into
turesize.
Fixes: 9cbe9fd5214e ("net: hns: optimize XGE capability by reducing cpu usage")
Signed-off-by: Huazhong tan <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/hisilicon/hns/hns_enet.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/net/ethernet/hisilicon/hns/hns_enet.c
+++ b/drivers/net/ethernet/hisilicon/hns/hns_enet.c
@@ -530,7 +530,7 @@ static void hns_nic_reuse_page(struct sk
}
skb_add_rx_frag(skb, i, desc_cb->priv, desc_cb->page_offset + pull_len,
- size - pull_len, truesize - pull_len);
+ size - pull_len, truesize);
/* avoid re-using remote pages,flag default unreuse */
if (unlikely(page_to_nid(desc_cb->priv) != numa_node_id()))
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Marc Zyngier <[email protected]>
[ Upstream commit 755a8bf5579d22eb5636685c516d8dede799e27b ]
If someone has the silly idea to write something along those lines:
extern u64 foo(void);
void bar(struct arm_smccc_res *res)
{
arm_smccc_1_1_smc(0xbad, foo(), res);
}
they are in for a surprise, as this gets compiled as:
0000000000000588 <bar>:
588: a9be7bfd stp x29, x30, [sp, #-32]!
58c: 910003fd mov x29, sp
590: f9000bf3 str x19, [sp, #16]
594: aa0003f3 mov x19, x0
598: aa1e03e0 mov x0, x30
59c: 94000000 bl 0 <_mcount>
5a0: 94000000 bl 0 <foo>
5a4: aa0003e1 mov x1, x0
5a8: d4000003 smc #0x0
5ac: b4000073 cbz x19, 5b8 <bar+0x30>
5b0: a9000660 stp x0, x1, [x19]
5b4: a9010e62 stp x2, x3, [x19, #16]
5b8: f9400bf3 ldr x19, [sp, #16]
5bc: a8c27bfd ldp x29, x30, [sp], #32
5c0: d65f03c0 ret
5c4: d503201f nop
The call to foo "overwrites" the x0 register for the return value,
and we end up calling the wrong secure service.
A solution is to evaluate all the parameters before assigning
anything to specific registers, leading to the expected result:
0000000000000588 <bar>:
588: a9be7bfd stp x29, x30, [sp, #-32]!
58c: 910003fd mov x29, sp
590: f9000bf3 str x19, [sp, #16]
594: aa0003f3 mov x19, x0
598: aa1e03e0 mov x0, x30
59c: 94000000 bl 0 <_mcount>
5a0: 94000000 bl 0 <foo>
5a4: aa0003e1 mov x1, x0
5a8: d28175a0 mov x0, #0xbad
5ac: d4000003 smc #0x0
5b0: b4000073 cbz x19, 5bc <bar+0x34>
5b4: a9000660 stp x0, x1, [x19]
5b8: a9010e62 stp x2, x3, [x19, #16]
5bc: f9400bf3 ldr x19, [sp, #16]
5c0: a8c27bfd ldp x29, x30, [sp], #32
5c4: d65f03c0 ret
Reported-by: Julien Grall <[email protected]>
Signed-off-by: Marc Zyngier <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
include/linux/arm-smccc.h | 30 ++++++++++++++++++++----------
1 file changed, 20 insertions(+), 10 deletions(-)
--- a/include/linux/arm-smccc.h
+++ b/include/linux/arm-smccc.h
@@ -205,41 +205,51 @@ asmlinkage void __arm_smccc_hvc(unsigned
register unsigned long r3 asm("r3")
#define __declare_arg_1(a0, a1, res) \
+ typeof(a1) __a1 = a1; \
struct arm_smccc_res *___res = res; \
register unsigned long r0 asm("r0") = (u32)a0; \
- register unsigned long r1 asm("r1") = a1; \
+ register unsigned long r1 asm("r1") = __a1; \
register unsigned long r2 asm("r2"); \
register unsigned long r3 asm("r3")
#define __declare_arg_2(a0, a1, a2, res) \
+ typeof(a1) __a1 = a1; \
+ typeof(a2) __a2 = a2; \
struct arm_smccc_res *___res = res; \
register unsigned long r0 asm("r0") = (u32)a0; \
- register unsigned long r1 asm("r1") = a1; \
- register unsigned long r2 asm("r2") = a2; \
+ register unsigned long r1 asm("r1") = __a1; \
+ register unsigned long r2 asm("r2") = __a2; \
register unsigned long r3 asm("r3")
#define __declare_arg_3(a0, a1, a2, a3, res) \
+ typeof(a1) __a1 = a1; \
+ typeof(a2) __a2 = a2; \
+ typeof(a3) __a3 = a3; \
struct arm_smccc_res *___res = res; \
register unsigned long r0 asm("r0") = (u32)a0; \
- register unsigned long r1 asm("r1") = a1; \
- register unsigned long r2 asm("r2") = a2; \
- register unsigned long r3 asm("r3") = a3
+ register unsigned long r1 asm("r1") = __a1; \
+ register unsigned long r2 asm("r2") = __a2; \
+ register unsigned long r3 asm("r3") = __a3
#define __declare_arg_4(a0, a1, a2, a3, a4, res) \
+ typeof(a4) __a4 = a4; \
__declare_arg_3(a0, a1, a2, a3, res); \
- register typeof(a4) r4 asm("r4") = a4
+ register unsigned long r4 asm("r4") = __a4
#define __declare_arg_5(a0, a1, a2, a3, a4, a5, res) \
+ typeof(a5) __a5 = a5; \
__declare_arg_4(a0, a1, a2, a3, a4, res); \
- register typeof(a5) r5 asm("r5") = a5
+ register unsigned long r5 asm("r5") = __a5
#define __declare_arg_6(a0, a1, a2, a3, a4, a5, a6, res) \
+ typeof(a6) __a6 = a6; \
__declare_arg_5(a0, a1, a2, a3, a4, a5, res); \
- register typeof(a6) r6 asm("r6") = a6
+ register unsigned long r6 asm("r6") = __a6
#define __declare_arg_7(a0, a1, a2, a3, a4, a5, a6, a7, res) \
+ typeof(a7) __a7 = a7; \
__declare_arg_6(a0, a1, a2, a3, a4, a5, a6, res); \
- register typeof(a7) r7 asm("r7") = a7
+ register unsigned long r7 asm("r7") = __a7
#define ___declare_args(count, ...) __declare_arg_ ## count(__VA_ARGS__)
#define __declare_args(count, ...) ___declare_args(count, __VA_ARGS__)
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Bo Chen <[email protected]>
[ Upstream commit cf1acec008f8d7761aa3fd7c4bca7e17b2d2512d ]
When the device is not up, the call to 'e1000_up()' from the error handling path
of 'e1000_set_ringparam()' causes a kernel oops with a null-pointer
dereference. The null-pointer dereference is triggered in function
'e1000_alloc_rx_buffers()' at line 'buffer_info = &rx_ring->buffer_info[i]'.
This bug was reported by COD, a tool for testing kernel module binaries I am
building. This bug was also detected by KFI from Dr. Kai Cong.
This patch fixes the bug by checking on 'netif_running()' before calling
'e1000_up()' in 'e1000_set_ringparam()'.
Signed-off-by: Bo Chen <[email protected]>
Acked-by: Alexander Duyck <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/intel/e1000/e1000_ethtool.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
--- a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c
+++ b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c
@@ -664,7 +664,8 @@ err_setup_rx:
err_alloc_rx:
kfree(txdr);
err_alloc_tx:
- e1000_up(adapter);
+ if (netif_running(adapter->netdev))
+ e1000_up(adapter);
err_setup:
clear_bit(__E1000_RESETTING, &adapter->flags);
return err;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Eric Sandeen <[email protected]>
[ Upstream commit 09a4e0be5826aa66c4ce9954841f110ffe63ef4f ]
The largest block size supported by isofs is ISOFS_BLOCK_SIZE (2048), but
isofs_fill_super calls sb_min_blocksize and sets the blocksize to the
device's logical block size if it's larger than what we ended up with after
option parsing.
If for some reason we try to mount a hard 4k device as an isofs filesystem,
we'll set opt.blocksize to 4096, and when we try to read the superblock
we found via:
block = iso_blknum << (ISOFS_BLOCK_BITS - s->s_blocksize_bits)
with s_blocksize_bits greater than ISOFS_BLOCK_BITS, we'll have a negative
shift and the bread will fail somewhat cryptically:
isofs_fill_super: bread failed, dev=sda, iso_blknum=17, block=-2147483648
It seems best to just catch and clearly reject mounts of such a device.
Reported-by: Bryan Gurney <[email protected]>
Signed-off-by: Eric Sandeen <[email protected]>
Signed-off-by: Jan Kara <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/isofs/inode.c | 7 +++++++
1 file changed, 7 insertions(+)
--- a/fs/isofs/inode.c
+++ b/fs/isofs/inode.c
@@ -24,6 +24,7 @@
#include <linux/mpage.h>
#include <linux/user_namespace.h>
#include <linux/seq_file.h>
+#include <linux/blkdev.h>
#include "isofs.h"
#include "zisofs.h"
@@ -653,6 +654,12 @@ static int isofs_fill_super(struct super
/*
* What if bugger tells us to go beyond page size?
*/
+ if (bdev_logical_block_size(s->s_bdev) > 2048) {
+ printk(KERN_WARNING
+ "ISOFS: unsupported/invalid hardware sector size %d\n",
+ bdev_logical_block_size(s->s_bdev));
+ goto out_freesbi;
+ }
opt.blocksize = sb_min_blocksize(s, opt.blocksize);
sbi->s_high_sierra = 0; /* default is iso9660 */
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: James Smart <[email protected]>
[ Upstream commit afd299ca996929f4f98ac20da0044c0cdc124879 ]
When a targetport is removed from the config, fcloop will avoid calling
the LS done() routine thinking the targetport is gone. This leaves the
initiator reset/reconnect hanging as it waits for a status on the
Create_Association LS for the reconnect.
Change the filter in the LS callback path. If tport null (set when
failed validation before "sending to remote port"), be sure to call
done. This was the main bug. But, continue the logic that only calls
done if tport was set but there is no remoteport (e.g. case where
remoteport has been removed, thus host doesn't expect a completion).
Signed-off-by: James Smart <[email protected]>
Signed-off-by: Christoph Hellwig <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/nvme/target/fcloop.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
--- a/drivers/nvme/target/fcloop.c
+++ b/drivers/nvme/target/fcloop.c
@@ -300,7 +300,7 @@ fcloop_tgt_lsrqst_done_work(struct work_
struct fcloop_tport *tport = tls_req->tport;
struct nvmefc_ls_req *lsreq = tls_req->lsreq;
- if (tport->remoteport)
+ if (!tport || tport->remoteport)
lsreq->done(lsreq, tls_req->status);
}
@@ -318,6 +318,7 @@ fcloop_ls_req(struct nvme_fc_local_port
if (!rport->targetport) {
tls_req->status = -ECONNREFUSED;
+ tls_req->tport = NULL;
schedule_work(&tls_req->work);
return ret;
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Anson Huang <[email protected]>
[ Upstream commit 152395fd03d4ce1e535a75cdbf58105e50587611 ]
When thermal zone is in passive mode, disabling its mode from
sysfs is NOT taking effect at all, it is still polling the
temperature of the disabled thermal zone and handling all thermal
trips, it makes user confused. The disabling operation should
disable the thermal zone behavior completely, for both active and
passive mode, this patch clears the passive_delay when thermal
zone is disabled and restores it when it is enabled.
Signed-off-by: Anson Huang <[email protected]>
Signed-off-by: Eduardo Valentin <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/thermal/of-thermal.c | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
--- a/drivers/thermal/of-thermal.c
+++ b/drivers/thermal/of-thermal.c
@@ -278,10 +278,13 @@ static int of_thermal_set_mode(struct th
mutex_lock(&tz->lock);
- if (mode == THERMAL_DEVICE_ENABLED)
+ if (mode == THERMAL_DEVICE_ENABLED) {
tz->polling_delay = data->polling_delay;
- else
+ tz->passive_delay = data->passive_delay;
+ } else {
tz->polling_delay = 0;
+ tz->passive_delay = 0;
+ }
mutex_unlock(&tz->lock);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Tomer Tayar <[email protected]>
[ Upstream commit b310974e041913231b6e3d5d475d4df55c312301 ]
Keep sending mailbox commands to the MFW when it is not responsive ends up
with a redundant amount of timeout expiries.
This patch prints the MCP status on the first command which is not
responded, and blocks the following commands.
Since the (un)load request commands might be not responded due to other
PFs, the patch also adds the option to skip the blocking upon a failure.
Signed-off-by: Tomer Tayar <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/qlogic/qed/qed_mcp.c | 52 ++++++++++++++++++++++++-
drivers/net/ethernet/qlogic/qed/qed_mcp.h | 6 ++
drivers/net/ethernet/qlogic/qed/qed_reg_addr.h | 1
3 files changed, 56 insertions(+), 3 deletions(-)
--- a/drivers/net/ethernet/qlogic/qed/qed_mcp.c
+++ b/drivers/net/ethernet/qlogic/qed/qed_mcp.c
@@ -319,6 +319,12 @@ int qed_mcp_reset(struct qed_hwfn *p_hwf
u32 org_mcp_reset_seq, seq, delay = QED_MCP_RESP_ITER_US, cnt = 0;
int rc = 0;
+ if (p_hwfn->mcp_info->b_block_cmd) {
+ DP_NOTICE(p_hwfn,
+ "The MFW is not responsive. Avoid sending MCP_RESET mailbox command.\n");
+ return -EBUSY;
+ }
+
/* Ensure that only a single thread is accessing the mailbox */
spin_lock_bh(&p_hwfn->mcp_info->cmd_lock);
@@ -444,6 +450,33 @@ static void __qed_mcp_cmd_and_union(stru
(p_mb_params->cmd | seq_num), p_mb_params->param);
}
+static void qed_mcp_cmd_set_blocking(struct qed_hwfn *p_hwfn, bool block_cmd)
+{
+ p_hwfn->mcp_info->b_block_cmd = block_cmd;
+
+ DP_INFO(p_hwfn, "%s sending of mailbox commands to the MFW\n",
+ block_cmd ? "Block" : "Unblock");
+}
+
+static void qed_mcp_print_cpu_info(struct qed_hwfn *p_hwfn,
+ struct qed_ptt *p_ptt)
+{
+ u32 cpu_mode, cpu_state, cpu_pc_0, cpu_pc_1, cpu_pc_2;
+ u32 delay = QED_MCP_RESP_ITER_US;
+
+ cpu_mode = qed_rd(p_hwfn, p_ptt, MCP_REG_CPU_MODE);
+ cpu_state = qed_rd(p_hwfn, p_ptt, MCP_REG_CPU_STATE);
+ cpu_pc_0 = qed_rd(p_hwfn, p_ptt, MCP_REG_CPU_PROGRAM_COUNTER);
+ udelay(delay);
+ cpu_pc_1 = qed_rd(p_hwfn, p_ptt, MCP_REG_CPU_PROGRAM_COUNTER);
+ udelay(delay);
+ cpu_pc_2 = qed_rd(p_hwfn, p_ptt, MCP_REG_CPU_PROGRAM_COUNTER);
+
+ DP_NOTICE(p_hwfn,
+ "MCP CPU info: mode 0x%08x, state 0x%08x, pc {0x%08x, 0x%08x, 0x%08x}\n",
+ cpu_mode, cpu_state, cpu_pc_0, cpu_pc_1, cpu_pc_2);
+}
+
static int
_qed_mcp_cmd_and_union(struct qed_hwfn *p_hwfn,
struct qed_ptt *p_ptt,
@@ -530,11 +563,15 @@ _qed_mcp_cmd_and_union(struct qed_hwfn *
DP_NOTICE(p_hwfn,
"The MFW failed to respond to command 0x%08x [param 0x%08x].\n",
p_mb_params->cmd, p_mb_params->param);
+ qed_mcp_print_cpu_info(p_hwfn, p_ptt);
spin_lock_bh(&p_hwfn->mcp_info->cmd_lock);
qed_mcp_cmd_del_elem(p_hwfn, p_cmd_elem);
spin_unlock_bh(&p_hwfn->mcp_info->cmd_lock);
+ if (!QED_MB_FLAGS_IS_SET(p_mb_params, AVOID_BLOCK))
+ qed_mcp_cmd_set_blocking(p_hwfn, true);
+
return -EAGAIN;
}
@@ -572,6 +609,13 @@ static int qed_mcp_cmd_and_union(struct
return -EBUSY;
}
+ if (p_hwfn->mcp_info->b_block_cmd) {
+ DP_NOTICE(p_hwfn,
+ "The MFW is not responsive. Avoid sending mailbox command 0x%08x [param 0x%08x].\n",
+ p_mb_params->cmd, p_mb_params->param);
+ return -EBUSY;
+ }
+
if (p_mb_params->data_src_size > union_data_size ||
p_mb_params->data_dst_size > union_data_size) {
DP_ERR(p_hwfn,
@@ -776,7 +820,7 @@ __qed_mcp_load_req(struct qed_hwfn *p_hw
mb_params.data_src_size = sizeof(load_req);
mb_params.p_data_dst = &load_rsp;
mb_params.data_dst_size = sizeof(load_rsp);
- mb_params.flags = QED_MB_FLAG_CAN_SLEEP;
+ mb_params.flags = QED_MB_FLAG_CAN_SLEEP | QED_MB_FLAG_AVOID_BLOCK;
DP_VERBOSE(p_hwfn, QED_MSG_SP,
"Load Request: param 0x%08x [init_hw %d, drv_type %d, hsi_ver %d, pda 0x%04x]\n",
@@ -1020,7 +1064,7 @@ int qed_mcp_unload_req(struct qed_hwfn *
memset(&mb_params, 0, sizeof(mb_params));
mb_params.cmd = DRV_MSG_CODE_UNLOAD_REQ;
mb_params.param = wol_param;
- mb_params.flags = QED_MB_FLAG_CAN_SLEEP;
+ mb_params.flags = QED_MB_FLAG_CAN_SLEEP | QED_MB_FLAG_AVOID_BLOCK;
return qed_mcp_cmd_and_union(p_hwfn, p_ptt, &mb_params);
}
@@ -2047,6 +2091,8 @@ int qed_mcp_halt(struct qed_hwfn *p_hwfn
return -EBUSY;
}
+ qed_mcp_cmd_set_blocking(p_hwfn, true);
+
return 0;
}
@@ -2071,6 +2117,8 @@ int qed_mcp_resume(struct qed_hwfn *p_hw
return -EBUSY;
}
+ qed_mcp_cmd_set_blocking(p_hwfn, false);
+
return 0;
}
--- a/drivers/net/ethernet/qlogic/qed/qed_mcp.h
+++ b/drivers/net/ethernet/qlogic/qed/qed_mcp.h
@@ -540,11 +540,14 @@ struct qed_mcp_info {
*/
spinlock_t cmd_lock;
+ /* Flag to indicate whether sending a MFW mailbox command is blocked */
+ bool b_block_cmd;
+
/* Spinlock used for syncing SW link-changes and link-changes
* originating from attention context.
*/
spinlock_t link_lock;
- bool block_mb_sending;
+
u32 public_base;
u32 drv_mb_addr;
u32 mfw_mb_addr;
@@ -575,6 +578,7 @@ struct qed_mcp_mb_params {
u32 mcp_param;
u32 flags;
#define QED_MB_FLAG_CAN_SLEEP (0x1 << 0)
+#define QED_MB_FLAG_AVOID_BLOCK (0x1 << 1)
#define QED_MB_FLAGS_IS_SET(params, flag) \
({ typeof(params) __params = (params); \
(__params && (__params->flags & QED_MB_FLAG_ ## flag)); })
--- a/drivers/net/ethernet/qlogic/qed/qed_reg_addr.h
+++ b/drivers/net/ethernet/qlogic/qed/qed_reg_addr.h
@@ -557,6 +557,7 @@
#define MCP_REG_CPU_STATE_SOFT_HALTED (0x1UL << 10)
#define MCP_REG_CPU_EVENT_MASK \
0xe05008UL
+#define MCP_REG_CPU_PROGRAM_COUNTER 0xe0501cUL
#define PGLUE_B_REG_PF_BAR0_SIZE \
0x2aae60UL
#define PGLUE_B_REG_PF_BAR1_SIZE \
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Tomer Tayar <[email protected]>
[ Upstream commit eaa50fc59e5841910987e90b0438b2643041f508 ]
The MFW manages an internal lock to prevent concurrent hardware
(de)initialization of different PFs.
This, together with the busy-waiting for the MFW's responses for commands,
might lead to a deadlock during concurrent load or unload of PFs.
This patch adds the option to sleep within the busy-waiting, and uses it
for the (un)load requests (which are not sent from an interrupt context) to
prevent the possible deadlock.
Signed-off-by: Tomer Tayar <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/qlogic/qed/qed_mcp.c | 43 +++++++++++++++++++++---------
drivers/net/ethernet/qlogic/qed/qed_mcp.h | 21 +++++++++-----
2 files changed, 44 insertions(+), 20 deletions(-)
--- a/drivers/net/ethernet/qlogic/qed/qed_mcp.c
+++ b/drivers/net/ethernet/qlogic/qed/qed_mcp.c
@@ -47,7 +47,7 @@
#include "qed_reg_addr.h"
#include "qed_sriov.h"
-#define CHIP_MCP_RESP_ITER_US 10
+#define QED_MCP_RESP_ITER_US 10
#define QED_DRV_MB_MAX_RETRIES (500 * 1000) /* Account for 5 sec */
#define QED_MCP_RESET_RETRIES (50 * 1000) /* Account for 500 msec */
@@ -316,7 +316,7 @@ static void qed_mcp_reread_offsets(struc
int qed_mcp_reset(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt)
{
- u32 org_mcp_reset_seq, seq, delay = CHIP_MCP_RESP_ITER_US, cnt = 0;
+ u32 org_mcp_reset_seq, seq, delay = QED_MCP_RESP_ITER_US, cnt = 0;
int rc = 0;
/* Ensure that only a single thread is accessing the mailbox */
@@ -448,10 +448,10 @@ static int
_qed_mcp_cmd_and_union(struct qed_hwfn *p_hwfn,
struct qed_ptt *p_ptt,
struct qed_mcp_mb_params *p_mb_params,
- u32 max_retries, u32 delay)
+ u32 max_retries, u32 usecs)
{
+ u32 cnt = 0, msecs = DIV_ROUND_UP(usecs, 1000);
struct qed_mcp_cmd_elem *p_cmd_elem;
- u32 cnt = 0;
u16 seq_num;
int rc = 0;
@@ -474,7 +474,11 @@ _qed_mcp_cmd_and_union(struct qed_hwfn *
goto err;
spin_unlock_bh(&p_hwfn->mcp_info->cmd_lock);
- udelay(delay);
+
+ if (QED_MB_FLAGS_IS_SET(p_mb_params, CAN_SLEEP))
+ msleep(msecs);
+ else
+ udelay(usecs);
} while (++cnt < max_retries);
if (cnt >= max_retries) {
@@ -503,7 +507,11 @@ _qed_mcp_cmd_and_union(struct qed_hwfn *
* The spinlock stays locked until the list element is removed.
*/
- udelay(delay);
+ if (QED_MB_FLAGS_IS_SET(p_mb_params, CAN_SLEEP))
+ msleep(msecs);
+ else
+ udelay(usecs);
+
spin_lock_bh(&p_hwfn->mcp_info->cmd_lock);
if (p_cmd_elem->b_is_completed)
@@ -538,7 +546,7 @@ _qed_mcp_cmd_and_union(struct qed_hwfn *
"MFW mailbox: response 0x%08x param 0x%08x [after %d.%03d ms]\n",
p_mb_params->mcp_resp,
p_mb_params->mcp_param,
- (cnt * delay) / 1000, (cnt * delay) % 1000);
+ (cnt * usecs) / 1000, (cnt * usecs) % 1000);
/* Clear the sequence number from the MFW response */
p_mb_params->mcp_resp &= FW_MSG_CODE_MASK;
@@ -556,7 +564,7 @@ static int qed_mcp_cmd_and_union(struct
{
size_t union_data_size = sizeof(union drv_union_data);
u32 max_retries = QED_DRV_MB_MAX_RETRIES;
- u32 delay = CHIP_MCP_RESP_ITER_US;
+ u32 usecs = QED_MCP_RESP_ITER_US;
/* MCP not initialized */
if (!qed_mcp_is_init(p_hwfn)) {
@@ -573,8 +581,13 @@ static int qed_mcp_cmd_and_union(struct
return -EINVAL;
}
+ if (QED_MB_FLAGS_IS_SET(p_mb_params, CAN_SLEEP)) {
+ max_retries = DIV_ROUND_UP(max_retries, 1000);
+ usecs *= 1000;
+ }
+
return _qed_mcp_cmd_and_union(p_hwfn, p_ptt, p_mb_params, max_retries,
- delay);
+ usecs);
}
int qed_mcp_cmd(struct qed_hwfn *p_hwfn,
@@ -763,6 +776,7 @@ __qed_mcp_load_req(struct qed_hwfn *p_hw
mb_params.data_src_size = sizeof(load_req);
mb_params.p_data_dst = &load_rsp;
mb_params.data_dst_size = sizeof(load_rsp);
+ mb_params.flags = QED_MB_FLAG_CAN_SLEEP;
DP_VERBOSE(p_hwfn, QED_MSG_SP,
"Load Request: param 0x%08x [init_hw %d, drv_type %d, hsi_ver %d, pda 0x%04x]\n",
@@ -984,7 +998,8 @@ int qed_mcp_load_req(struct qed_hwfn *p_
int qed_mcp_unload_req(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt)
{
- u32 wol_param, mcp_resp, mcp_param;
+ struct qed_mcp_mb_params mb_params;
+ u32 wol_param;
switch (p_hwfn->cdev->wol_config) {
case QED_OV_WOL_DISABLED:
@@ -1002,8 +1017,12 @@ int qed_mcp_unload_req(struct qed_hwfn *
wol_param = DRV_MB_PARAM_UNLOAD_WOL_MCP;
}
- return qed_mcp_cmd(p_hwfn, p_ptt, DRV_MSG_CODE_UNLOAD_REQ, wol_param,
- &mcp_resp, &mcp_param);
+ memset(&mb_params, 0, sizeof(mb_params));
+ mb_params.cmd = DRV_MSG_CODE_UNLOAD_REQ;
+ mb_params.param = wol_param;
+ mb_params.flags = QED_MB_FLAG_CAN_SLEEP;
+
+ return qed_mcp_cmd_and_union(p_hwfn, p_ptt, &mb_params);
}
int qed_mcp_unload_done(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt)
--- a/drivers/net/ethernet/qlogic/qed/qed_mcp.h
+++ b/drivers/net/ethernet/qlogic/qed/qed_mcp.h
@@ -565,14 +565,19 @@ struct qed_mcp_info {
};
struct qed_mcp_mb_params {
- u32 cmd;
- u32 param;
- void *p_data_src;
- u8 data_src_size;
- void *p_data_dst;
- u8 data_dst_size;
- u32 mcp_resp;
- u32 mcp_param;
+ u32 cmd;
+ u32 param;
+ void *p_data_src;
+ void *p_data_dst;
+ u8 data_src_size;
+ u8 data_dst_size;
+ u32 mcp_resp;
+ u32 mcp_param;
+ u32 flags;
+#define QED_MB_FLAG_CAN_SLEEP (0x1 << 0)
+#define QED_MB_FLAGS_IS_SET(params, flag) \
+ ({ typeof(params) __params = (params); \
+ (__params && (__params->flags & QED_MB_FLAG_ ## flag)); })
};
/**
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Amir Goldstein <[email protected]>
commit 764baba80168ad3adafb521d2ab483ccbc49e344 upstream.
Commit 31747eda41ef ("ovl: hash directory inodes for fsnotify")
fixed an issue of inotify watch on directory that stops getting
events after dropping dentry caches.
A similar issue exists for non-dir non-upper files, for example:
$ mkdir -p lower upper work merged
$ touch lower/foo
$ mount -t overlay -o
lowerdir=lower,workdir=work,upperdir=upper none merged
$ inotifywait merged/foo &
$ echo 2 > /proc/sys/vm/drop_caches
$ cat merged/foo
inotifywait doesn't get the OPEN event, because ovl_lookup() called
from 'cat' allocates a new overlay inode and does not reuse the
watched inode.
Fix this by hashing non-dir overlay inodes by lower real inode in
the following cases that were not hashed before this change:
- A non-upper overlay mount
- A lower non-hardlink when index=off
A helper ovl_hash_bylower() was added to put all the logic and
documentation about which real inode an overlay inode is hashed by
into one place.
The issue dates back to initial version of overlayfs, but this
patch depends on ovl_inode code that was introduced in kernel v4.13.
Cc: <[email protected]> #v4.13
Signed-off-by: Amir Goldstein <[email protected]>
Signed-off-by: Miklos Szeredi <[email protected]>
Signed-off-by: Mark Salyzyn <[email protected]> #4.14
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/overlayfs/inode.c | 62 ++++++++++++++++++++++++++++++++++++---------------
1 file changed, 44 insertions(+), 18 deletions(-)
--- a/fs/overlayfs/inode.c
+++ b/fs/overlayfs/inode.c
@@ -14,6 +14,7 @@
#include <linux/posix_acl.h>
#include <linux/ratelimit.h>
#include "overlayfs.h"
+#include "ovl_entry.h"
int ovl_setattr(struct dentry *dentry, struct iattr *attr)
{
@@ -608,39 +609,63 @@ static bool ovl_verify_inode(struct inod
return true;
}
+/*
+ * Does overlay inode need to be hashed by lower inode?
+ */
+static bool ovl_hash_bylower(struct super_block *sb, struct dentry *upper,
+ struct dentry *lower, struct dentry *index)
+{
+ struct ovl_fs *ofs = sb->s_fs_info;
+
+ /* No, if pure upper */
+ if (!lower)
+ return false;
+
+ /* Yes, if already indexed */
+ if (index)
+ return true;
+
+ /* Yes, if won't be copied up */
+ if (!ofs->upper_mnt)
+ return true;
+
+ /* No, if lower hardlink is or will be broken on copy up */
+ if ((upper || !ovl_indexdir(sb)) &&
+ !d_is_dir(lower) && d_inode(lower)->i_nlink > 1)
+ return false;
+
+ /* No, if non-indexed upper with NFS export */
+ if (sb->s_export_op && upper)
+ return false;
+
+ /* Otherwise, hash by lower inode for fsnotify */
+ return true;
+}
+
struct inode *ovl_get_inode(struct dentry *dentry, struct dentry *upperdentry,
struct dentry *index)
{
+ struct super_block *sb = dentry->d_sb;
struct dentry *lowerdentry = ovl_dentry_lower(dentry);
struct inode *realinode = upperdentry ? d_inode(upperdentry) : NULL;
struct inode *inode;
- /* Already indexed or could be indexed on copy up? */
- bool indexed = (index || (ovl_indexdir(dentry->d_sb) && !upperdentry));
- struct dentry *origin = indexed ? lowerdentry : NULL;
+ bool bylower = ovl_hash_bylower(sb, upperdentry, lowerdentry, index);
bool is_dir;
- if (WARN_ON(upperdentry && indexed && !lowerdentry))
- return ERR_PTR(-EIO);
-
if (!realinode)
realinode = d_inode(lowerdentry);
/*
- * Copy up origin (lower) may exist for non-indexed non-dir upper, but
- * we must not use lower as hash key in that case.
- * Hash non-dir that is or could be indexed by origin inode.
- * Hash dir that is or could be merged by origin inode.
- * Hash pure upper and non-indexed non-dir by upper inode.
+ * Copy up origin (lower) may exist for non-indexed upper, but we must
+ * not use lower as hash key if this is a broken hardlink.
*/
is_dir = S_ISDIR(realinode->i_mode);
- if (is_dir)
- origin = lowerdentry;
-
- if (upperdentry || origin) {
- struct inode *key = d_inode(origin ?: upperdentry);
+ if (upperdentry || bylower) {
+ struct inode *key = d_inode(bylower ? lowerdentry :
+ upperdentry);
unsigned int nlink = is_dir ? 1 : realinode->i_nlink;
- inode = iget5_locked(dentry->d_sb, (unsigned long) key,
+ inode = iget5_locked(sb, (unsigned long) key,
ovl_inode_test, ovl_inode_set, key);
if (!inode)
goto out_nomem;
@@ -664,7 +689,8 @@ struct inode *ovl_get_inode(struct dentr
nlink = ovl_get_nlink(lowerdentry, upperdentry, nlink);
set_nlink(inode, nlink);
} else {
- inode = new_inode(dentry->d_sb);
+ /* Lower hardlink that will be broken on copy up */
+ inode = new_inode(sb);
if (!inode)
goto out_nomem;
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Steve Wise <[email protected]>
commit 67e3816842fe6414d629c7515b955952ec40c7d7 upstream.
Currently a uverbs completion event queue is flushed of events in
ib_uverbs_comp_event_close() with the queue spinlock held and then
released. Yet setting ev_queue->is_closed is not set until later in
uverbs_hot_unplug_completion_event_file().
In between the time ib_uverbs_comp_event_close() releases the lock and
uverbs_hot_unplug_completion_event_file() acquires the lock, a completion
event can arrive and be inserted into the event queue by
ib_uverbs_comp_handler().
This can cause a "double add" list_add warning or crash depending on the
kernel configuration, or a memory leak because the event is never dequeued
since the queue is already closed down.
So add setting ev_queue->is_closed = 1 to ib_uverbs_comp_event_close().
Cc: [email protected]
Fixes: 1e7710f3f656 ("IB/core: Change completion channel to use the reworked objects schema")
Signed-off-by: Steve Wise <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/infiniband/core/uverbs_main.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/infiniband/core/uverbs_main.c
+++ b/drivers/infiniband/core/uverbs_main.c
@@ -424,6 +424,7 @@ static int ib_uverbs_comp_event_close(st
list_del(&entry->obj_list);
kfree(entry);
}
+ file->ev_queue.is_closed = 1;
spin_unlock_irq(&file->ev_queue.lock);
uverbs_close_fd(filp);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: John Fastabend <[email protected]>
[ Upstream commit 9b2e0388bec8ec5427403e23faff3b58dd1c3200 ]
When sockmap code is using the stream parser it also handles the write
space events in order to handle the case where (a) verdict redirects
skb to another socket and (b) the sockmap then sends the skb but due
to memory constraints (or other EAGAIN errors) needs to do a retry.
But the initial code missed a third case where the
skb_send_sock_locked() triggers an sk_wait_event(). A typically case
would be when sndbuf size is exceeded. If this happens because we
do not pass the write_space event to the lower layers we never wake
up the event and it will wait for sndtimeo. Which as noted in ktls
fix may be rather large and look like a hang to the user.
To reproduce the best test is to reduce the sndbuf size and send
1B data chunks to stress the memory handling. To fix this pass the
event from the upper layer to the lower layer.
Signed-off-by: John Fastabend <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
kernel/bpf/sockmap.c | 3 +++
1 file changed, 3 insertions(+)
--- a/kernel/bpf/sockmap.c
+++ b/kernel/bpf/sockmap.c
@@ -313,12 +313,15 @@ out:
static void smap_write_space(struct sock *sk)
{
struct smap_psock *psock;
+ void (*write_space)(struct sock *sk);
rcu_read_lock();
psock = smap_psock_sk(sk);
if (likely(psock && test_bit(SMAP_TX_RUNNING, &psock->state)))
schedule_work(&psock->tx_work);
+ write_space = psock->save_write_space;
rcu_read_unlock();
+ write_space(sk);
}
static void smap_stop_sock(struct smap_psock *psock, struct sock *sk)
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Michael J. Ruhl <[email protected]>
commit d623500b3c4efd8d4e945ac9003c6b87b469a9ab upstream.
If a packet stream uses an UnsupportedVL (virtual lane), the send
engine will not send the packet, and it will not indicate that an
error has occurred. This will cause the packet stream to block.
HFI has 8 virtual lanes available for packet streams. Each lane can
be enabled or disabled using the UnsupportedVL mask. If a lane is
disabled, adding a packet to the send context must be disallowed.
The current mask for determining unsupported VLs defaults to 0 (allow
all). This is incorrect. Only the VLs that are defined should be
allowed.
Determine which VLs are disabled (mtu == 0), and set the appropriate
unsupported bit in the mask. The correct mask will allow the send
engine to error on the invalid VL, and error recovery will work
correctly.
Cc: <[email protected]> # 4.9.x+
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Reviewed-by: Mike Marciniszyn <[email protected]>
Reviewed-by: Lukasz Odzioba <[email protected]>
Signed-off-by: Michael J. Ruhl <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/infiniband/hw/hfi1/pio.c | 9 +++++++--
1 file changed, 7 insertions(+), 2 deletions(-)
--- a/drivers/infiniband/hw/hfi1/pio.c
+++ b/drivers/infiniband/hw/hfi1/pio.c
@@ -86,6 +86,7 @@ void pio_send_control(struct hfi1_devdat
unsigned long flags;
int write = 1; /* write sendctrl back */
int flush = 0; /* re-read sendctrl to make sure it is flushed */
+ int i;
spin_lock_irqsave(&dd->sendctrl_lock, flags);
@@ -95,9 +96,13 @@ void pio_send_control(struct hfi1_devdat
reg |= SEND_CTRL_SEND_ENABLE_SMASK;
/* Fall through */
case PSC_DATA_VL_ENABLE:
+ mask = 0;
+ for (i = 0; i < ARRAY_SIZE(dd->vld); i++)
+ if (!dd->vld[i].mtu)
+ mask |= BIT_ULL(i);
/* Disallow sending on VLs not enabled */
- mask = (((~0ull) << num_vls) & SEND_CTRL_UNSUPPORTED_VL_MASK) <<
- SEND_CTRL_UNSUPPORTED_VL_SHIFT;
+ mask = (mask & SEND_CTRL_UNSUPPORTED_VL_MASK) <<
+ SEND_CTRL_UNSUPPORTED_VL_SHIFT;
reg = (reg & ~SEND_CTRL_UNSUPPORTED_VL_SMASK) | mask;
break;
case PSC_GLOBAL_DISABLE:
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Ira Weiny <[email protected]>
commit 0dbfaa9f2813787679e296eb5476e40938ab48c8 upstream.
The SL specified by a user needs to be a valid SL.
Add a range check to the user specified SL value which protects from
running off the end of the SL to SC table.
CC: [email protected]
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Signed-off-by: Ira Weiny <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/infiniband/hw/hfi1/verbs.c | 8 +++++++-
1 file changed, 7 insertions(+), 1 deletion(-)
--- a/drivers/infiniband/hw/hfi1/verbs.c
+++ b/drivers/infiniband/hw/hfi1/verbs.c
@@ -1573,6 +1573,7 @@ static int hfi1_check_ah(struct ib_devic
struct hfi1_pportdata *ppd;
struct hfi1_devdata *dd;
u8 sc5;
+ u8 sl;
if (hfi1_check_mcast(rdma_ah_get_dlid(ah_attr)) &&
!(rdma_ah_get_ah_flags(ah_attr) & IB_AH_GRH))
@@ -1581,8 +1582,13 @@ static int hfi1_check_ah(struct ib_devic
/* test the mapping for validity */
ibp = to_iport(ibdev, rdma_ah_get_port_num(ah_attr));
ppd = ppd_from_ibp(ibp);
- sc5 = ibp->sl_to_sc[rdma_ah_get_sl(ah_attr)];
dd = dd_from_ppd(ppd);
+
+ sl = rdma_ah_get_sl(ah_attr);
+ if (sl >= ARRAY_SIZE(ibp->sl_to_sc))
+ return -EINVAL;
+
+ sc5 = ibp->sl_to_sc[sl];
if (sc_to_vlt(dd, sc5) > num_vls && sc_to_vlt(dd, sc5) != 0xf)
return -EINVAL;
return 0;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: John Fastabend <[email protected]>
[ Upstream commit 67db7cd249e71f64346f481b629724376d063e08 ]
Currently, the lower protocols sk_write_space handler is not called if
TLS is sending a scatterlist via tls_push_sg. However, normally
tls_push_sg calls do_tcp_sendpage, which may be under memory pressure,
that in turn may trigger a wait via sk_wait_event. Typically, this
happens when the in-flight bytes exceed the sdnbuf size. In the normal
case when enough ACKs are received sk_write_space() will be called and
the sk_wait_event will be woken up allowing it to send more data
and/or return to the user.
But, in the TLS case because the sk_write_space() handler does not
wake up the events the above send will wait until the sndtimeo is
exceeded. By default this is MAX_SCHEDULE_TIMEOUT so it look like a
hang to the user (especially this impatient user). To fix this pass
the sk_write_space event to the lower layers sk_write_space event
which in the TCP case will wake any pending events.
I observed the above while integrating sockmap and ktls. It
initially appeared as test_sockmap (modified to use ktls) occasionally
hanging. To reliably reproduce this reduce the sndbuf size and stress
the tls layer by sending many 1B sends. This results in every byte
needing a header and each byte individually being sent to the crypto
layer.
Signed-off-by: John Fastabend <[email protected]>
Acked-by: Dave Watson <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/tls/tls_main.c | 9 +++++++--
1 file changed, 7 insertions(+), 2 deletions(-)
--- a/net/tls/tls_main.c
+++ b/net/tls/tls_main.c
@@ -195,9 +195,14 @@ static void tls_write_space(struct sock
{
struct tls_context *ctx = tls_get_ctx(sk);
- /* We are already sending pages, ignore notification */
- if (ctx->in_tcp_sendpages)
+ /* If in_tcp_sendpages call lower protocol write space handler
+ * to ensure we wake up any waiting operations there. For example
+ * if do_tcp_sendpages where to call sk_wait_event.
+ */
+ if (ctx->in_tcp_sendpages) {
+ ctx->sk_write_space(sk);
return;
+ }
if (!sk->sk_write_pending && tls_is_pending_closed_record(ctx)) {
gfp_t sk_allocation = sk->sk_allocation;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Bin Liu <[email protected]>
commit 783f3b4e9ec50491c21746e7e05ec6c39c21f563 upstream.
TI AM335x CPPI 4.1 module uses a single register bit for CPPI interrupts
in both musb controllers. So disabling the CPPI irq in one musb driver
breaks the other musb module.
Since musb is already disabled before tearing down dma controller in
musb_remove(), it is safe to not disable CPPI irq in
musb_dma_controller_destroy().
Fixes: 255348289f71 ("usb: musb: dsps: Manage CPPI 4.1 DMA interrupt in DSPS")
Cc: [email protected]
Signed-off-by: Bin Liu <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/musb/musb_dsps.c | 12 +-----------
1 file changed, 1 insertion(+), 11 deletions(-)
--- a/drivers/usb/musb/musb_dsps.c
+++ b/drivers/usb/musb/musb_dsps.c
@@ -684,16 +684,6 @@ dsps_dma_controller_create(struct musb *
return controller;
}
-static void dsps_dma_controller_destroy(struct dma_controller *c)
-{
- struct musb *musb = c->musb;
- struct dsps_glue *glue = dev_get_drvdata(musb->controller->parent);
- void __iomem *usbss_base = glue->usbss_base;
-
- musb_writel(usbss_base, USBSS_IRQ_CLEARR, USBSS_IRQ_PD_COMP);
- cppi41_dma_controller_destroy(c);
-}
-
#ifdef CONFIG_PM_SLEEP
static void dsps_dma_controller_suspend(struct dsps_glue *glue)
{
@@ -723,7 +713,7 @@ static struct musb_platform_ops dsps_ops
#ifdef CONFIG_USB_TI_CPPI41_DMA
.dma_init = dsps_dma_controller_create,
- .dma_exit = dsps_dma_controller_destroy,
+ .dma_exit = cppi41_dma_controller_destroy,
#endif
.enable = dsps_musb_enable,
.disable = dsps_musb_disable,
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Michael J. Ruhl <[email protected]>
commit 94694d18cf27a6faad91487a38ce516c2b16e7d9 upstream.
If the number of packets in a user sdma request does not match
the actual iovectors being sent, sdma_cleanup can be called on
an uninitialized request structure, resulting in a crash similar
to this:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffffc0ae8bb7>] __sdma_txclean+0x57/0x1e0 [hfi1]
PGD 8000001044f61067 PUD 1052706067 PMD 0
Oops: 0000 [#1] SMP
CPU: 30 PID: 69912 Comm: upsm Kdump: loaded Tainted: G OE
------------ 3.10.0-862.el7.x86_64 #1
Hardware name: Intel Corporation S2600KPR/S2600KPR, BIOS
SE5C610.86B.01.01.0019.101220160604 10/12/2016
task: ffff8b331c890000 ti: ffff8b2ed1f98000 task.ti: ffff8b2ed1f98000
RIP: 0010:[<ffffffffc0ae8bb7>] [<ffffffffc0ae8bb7>] __sdma_txclean+0x57/0x1e0
[hfi1]
RSP: 0018:ffff8b2ed1f9bab0 EFLAGS: 00010286
RAX: 0000000000008b2b RBX: ffff8b2adf6e0000 RCX: 0000000000000000
RDX: 00000000000000a0 RSI: ffff8b2e9eedc540 RDI: ffff8b2adf6e0000
RBP: ffff8b2ed1f9bad8 R08: 0000000000000000 R09: ffffffffc0b04a06
R10: ffff8b331c890190 R11: ffffe6ed00bf1840 R12: ffff8b3315480000
R13: ffff8b33154800f0 R14: 00000000fffffff2 R15: ffff8b2e9eedc540
FS: 00007f035ac47740(0000) GS:ffff8b331e100000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 0000000c03fe6000 CR4: 00000000001607e0
Call Trace:
[<ffffffffc0b0570d>] user_sdma_send_pkts+0xdcd/0x1990 [hfi1]
[<ffffffff9fe75fb0>] ? gup_pud_range+0x140/0x290
[<ffffffffc0ad3105>] ? hfi1_mmu_rb_insert+0x155/0x1b0 [hfi1]
[<ffffffffc0b0777b>] hfi1_user_sdma_process_request+0xc5b/0x11b0 [hfi1]
[<ffffffffc0ac193a>] hfi1_aio_write+0xba/0x110 [hfi1]
[<ffffffffa001a2bb>] do_sync_readv_writev+0x7b/0xd0
[<ffffffffa001bede>] do_readv_writev+0xce/0x260
[<ffffffffa022b089>] ? tty_ldisc_deref+0x19/0x20
[<ffffffffa02268c0>] ? n_tty_ioctl+0xe0/0xe0
[<ffffffffa001c105>] vfs_writev+0x35/0x60
[<ffffffffa001c2bf>] SyS_writev+0x7f/0x110
[<ffffffffa051f7d5>] system_call_fastpath+0x1c/0x21
Code: 06 49 c7 47 18 00 00 00 00 0f 87 89 01 00 00 5b 41 5c 41 5d 41 5e 41 5f
5d c3 66 2e 0f 1f 84 00 00 00 00 00 48 8b 4e 10 48 89 fb <48> 8b 51 08 49 89 d4
83 e2 0c 41 81 e4 00 e0 00 00 48 c1 ea 02
RIP [<ffffffffc0ae8bb7>] __sdma_txclean+0x57/0x1e0 [hfi1]
RSP <ffff8b2ed1f9bab0>
CR2: 0000000000000008
There are two exit points from user_sdma_send_pkts(). One (free_tx)
merely frees the slab entry and one (free_txreq) cleans the sdma_txreq
prior to freeing the slab entry. The free_txreq variation can only be
called after one of the sdma_init*() variations has been called.
In the panic case, the slab entry had been allocated but not inited.
Fix the issue by exiting through free_tx thus avoiding sdma_clean().
Cc: <[email protected]> # 4.9.x+
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Reviewed-by: Mike Marciniszyn <[email protected]>
Reviewed-by: Lukasz Odzioba <[email protected]>
Signed-off-by: Michael J. Ruhl <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
---
drivers/infiniband/hw/hfi1/user_sdma.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/infiniband/hw/hfi1/user_sdma.c
+++ b/drivers/infiniband/hw/hfi1/user_sdma.c
@@ -828,7 +828,7 @@ static int user_sdma_send_pkts(struct us
if (ACCESS_ONCE(iovec->offset) == iovec->iov.iov_len) {
if (++req->iov_idx == req->data_iovs) {
ret = -EFAULT;
- goto free_txreq;
+ goto free_tx;
}
iovec = &req->iovs[req->iov_idx];
WARN_ON(iovec->offset);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Dan Carpenter <[email protected]>
[ Upstream commit ae636fb1554833ee5133ca47bf4b2791b6739c52 ]
This is a static checker fix, not something I have tested. The issue
is that on the second iteration through the loop, we jump forward by
le32_to_cpu(auth_req->length) bytes. The problem is that if the length
is more than "buflen" then we end up with a negative "buflen". A
negative buflen is type promoted to a high positive value and the loop
continues but it's accessing beyond the end of the buffer.
I believe the "auth_req->length" comes from the firmware and if the
firmware is malicious or buggy, you're already toasted so the impact of
this bug is probably not very severe.
Fixes: 030645aceb3d ("rndis_wlan: handle 802.11 indications from device")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/wireless/rndis_wlan.c | 2 ++
1 file changed, 2 insertions(+)
--- a/drivers/net/wireless/rndis_wlan.c
+++ b/drivers/net/wireless/rndis_wlan.c
@@ -2928,6 +2928,8 @@ static void rndis_wlan_auth_indication(s
while (buflen >= sizeof(*auth_req)) {
auth_req = (void *)buf;
+ if (buflen < le32_to_cpu(auth_req->length))
+ return;
type = "unknown";
flags = le32_to_cpu(auth_req->flags);
pairwise_error = false;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Brandon Maier <[email protected]>
[ Upstream commit ab4e6ee578e88a659938db8fbf33720bc048d29c ]
Since a phy_device is added to the global mdio_bus list during
phy_device_register(), but a phy_device's phy_driver doesn't get
attached until phy_probe(). It's possible of_phy_find_device() in
xgmiitorgmii will return a valid phy with a NULL phy_driver. Leading to
a NULL pointer access during the memcpy().
Fixes this Oops:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.40 #1
Hardware name: Xilinx Zynq Platform
task: ce4c8d00 task.stack: ce4ca000
PC is at memcpy+0x48/0x330
LR is at xgmiitorgmii_probe+0x90/0xe8
pc : [<c074bc68>] lr : [<c0529548>] psr: 20000013
sp : ce4cbb54 ip : 00000000 fp : ce4cbb8c
r10: 00000000 r9 : 00000000 r8 : c0c49178
r7 : 00000000 r6 : cdc14718 r5 : ce762800 r4 : cdc14710
r3 : 00000000 r2 : 00000054 r1 : 00000000 r0 : cdc14718
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 18c5387d Table: 0000404a DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0xce4ca210)
...
[<c074bc68>] (memcpy) from [<c0529548>] (xgmiitorgmii_probe+0x90/0xe8)
[<c0529548>] (xgmiitorgmii_probe) from [<c0526a94>] (mdio_probe+0x28/0x34)
[<c0526a94>] (mdio_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbd58>] (__device_attach_driver+0xac/0x10c)
[<c04dbd58>] (__device_attach_driver) from [<c04d96f4>] (bus_for_each_drv+0x84/0xc8)
[<c04d96f4>] (bus_for_each_drv) from [<c04db5bc>] (__device_attach+0xd0/0x134)
[<c04db5bc>] (__device_attach) from [<c04dbdd4>] (device_initial_probe+0x1c/0x20)
[<c04dbdd4>] (device_initial_probe) from [<c04da8fc>] (bus_probe_device+0x98/0xa0)
[<c04da8fc>] (bus_probe_device) from [<c04d8660>] (device_add+0x43c/0x5d0)
[<c04d8660>] (device_add) from [<c0526cb8>] (mdio_device_register+0x34/0x80)
[<c0526cb8>] (mdio_device_register) from [<c0580b48>] (of_mdiobus_register+0x170/0x30c)
[<c0580b48>] (of_mdiobus_register) from [<c05349c4>] (macb_probe+0x710/0xc00)
[<c05349c4>] (macb_probe) from [<c04dd700>] (platform_drv_probe+0x44/0x80)
[<c04dd700>] (platform_drv_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbc58>] (__driver_attach+0x10c/0x118)
[<c04dbc58>] (__driver_attach) from [<c04d9600>] (bus_for_each_dev+0x8c/0xd0)
[<c04d9600>] (bus_for_each_dev) from [<c04db1fc>] (driver_attach+0x2c/0x30)
[<c04db1fc>] (driver_attach) from [<c04daa98>] (bus_add_driver+0x50/0x260)
[<c04daa98>] (bus_add_driver) from [<c04dc440>] (driver_register+0x88/0x108)
[<c04dc440>] (driver_register) from [<c04dd6b4>] (__platform_driver_register+0x50/0x58)
[<c04dd6b4>] (__platform_driver_register) from [<c0b31248>] (macb_driver_init+0x24/0x28)
[<c0b31248>] (macb_driver_init) from [<c010203c>] (do_one_initcall+0x60/0x1a4)
[<c010203c>] (do_one_initcall) from [<c0b00f78>] (kernel_init_freeable+0x15c/0x1f8)
[<c0b00f78>] (kernel_init_freeable) from [<c0763d10>] (kernel_init+0x18/0x124)
[<c0763d10>] (kernel_init) from [<c0112d74>] (ret_from_fork+0x14/0x20)
Code: ba000002 f5d1f03c f5d1f05c f5d1f07c (e8b151f8)
---[ end trace 3e4ec21905820a1f ]---
Signed-off-by: Brandon Maier <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/phy/xilinx_gmii2rgmii.c | 5 +++++
1 file changed, 5 insertions(+)
--- a/drivers/net/phy/xilinx_gmii2rgmii.c
+++ b/drivers/net/phy/xilinx_gmii2rgmii.c
@@ -84,6 +84,11 @@ static int xgmiitorgmii_probe(struct mdi
return -EPROBE_DEFER;
}
+ if (!priv->phy_dev->drv) {
+ dev_info(dev, "Attached phy not ready\n");
+ return -EPROBE_DEFER;
+ }
+
priv->addr = mdiodev->addr;
priv->phy_drv = priv->phy_dev->drv;
memcpy(&priv->conv_phy_drv, priv->phy_dev->drv,
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Alistair Strachan <[email protected]>
[ Upstream commit 8632c614565d0c5fdde527889601c018e97b6384 ]
The ashmem driver did not check that the size/offset of the vma passed
to its .mmap() function was not larger than the ashmem object being
mapped. This could cause mmap() to succeed, even though accessing parts
of the mapping would later fail with a segmentation fault.
Ensure an error is returned by the ashmem_mmap() function if the vma
size is larger than the ashmem object size. This enables safer handling
of the problem in userspace.
Cc: Todd Kjos <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: Joel Fernandes <[email protected]>
Signed-off-by: Alistair Strachan <[email protected]>
Acked-by: Joel Fernandes (Google) <[email protected]>
Reviewed-by: Martijn Coenen <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/staging/android/ashmem.c | 6 ++++++
1 file changed, 6 insertions(+)
--- a/drivers/staging/android/ashmem.c
+++ b/drivers/staging/android/ashmem.c
@@ -374,6 +374,12 @@ static int ashmem_mmap(struct file *file
goto out;
}
+ /* requested mapping size larger than object size */
+ if (vma->vm_end - vma->vm_start > PAGE_ALIGN(asma->size)) {
+ ret = -EINVAL;
+ goto out;
+ }
+
/* requested protection bits must match our allowed protection mask */
if (unlikely((vma->vm_flags & ~calc_vm_prot_bits(asma->prot_mask, 0)) &
calc_vm_prot_bits(PROT_MASK, 0))) {
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Jernej Skrabec <[email protected]>
[ Upstream commit 367c359aa8637b15ee8df6335c5a29b7623966ec ]
sun4i_drv_add_endpoints() has a memory leak since it uses of_node_put()
when remote is equal to NULL and does nothing when remote has a valid
pointer.
Invert the logic to fix memory leak.
Signed-off-by: Jernej Skrabec <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/gpu/drm/sun4i/sun4i_drv.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
--- a/drivers/gpu/drm/sun4i/sun4i_drv.c
+++ b/drivers/gpu/drm/sun4i/sun4i_drv.c
@@ -241,7 +241,6 @@ static int sun4i_drv_add_endpoints(struc
remote = of_graph_get_remote_port_parent(ep);
if (!remote) {
DRM_DEBUG_DRIVER("Error retrieving the output node\n");
- of_node_put(remote);
continue;
}
@@ -255,11 +254,13 @@ static int sun4i_drv_add_endpoints(struc
if (of_graph_parse_endpoint(ep, &endpoint)) {
DRM_DEBUG_DRIVER("Couldn't parse endpoint\n");
+ of_node_put(remote);
continue;
}
if (!endpoint.id) {
DRM_DEBUG_DRIVER("Endpoint is our panel... skipping\n");
+ of_node_put(remote);
continue;
}
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Ben Greear <[email protected]>
[ Upstream commit 168f75f11fe68455e0d058a818ebccfc329d8685 ]
While debugging driver crashes related to a buggy firmware
crashing under load, I noticed that ath10k_htt_rx_ring_free
could be called without being under lock. I'm not sure if this
is the root cause of the crash or not, but it seems prudent to
protect it.
Originally tested on 4.16+ kernel with ath10k-ct 10.4 firmware
running on 9984 NIC.
Signed-off-by: Ben Greear <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/wireless/ath/ath10k/htt_rx.c | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
--- a/drivers/net/wireless/ath/ath10k/htt_rx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_rx.c
@@ -215,11 +215,12 @@ int ath10k_htt_rx_ring_refill(struct ath
spin_lock_bh(&htt->rx_ring.lock);
ret = ath10k_htt_rx_ring_fill_n(htt, (htt->rx_ring.fill_level -
htt->rx_ring.fill_cnt));
- spin_unlock_bh(&htt->rx_ring.lock);
if (ret)
ath10k_htt_rx_ring_free(htt);
+ spin_unlock_bh(&htt->rx_ring.lock);
+
return ret;
}
@@ -231,7 +232,9 @@ void ath10k_htt_rx_free(struct ath10k_ht
skb_queue_purge(&htt->rx_in_ord_compl_q);
skb_queue_purge(&htt->tx_fetch_ind_q);
+ spin_lock_bh(&htt->rx_ring.lock);
ath10k_htt_rx_ring_free(htt);
+ spin_unlock_bh(&htt->rx_ring.lock);
dma_free_coherent(htt->ar->dev,
(htt->rx_ring.size *
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Geert Uytterhoeven <[email protected]>
commit 8dbbaa47b96f6ea5f09f922b4effff3c505cd8cf upstream.
When interrupted, wait_event_interruptible_timeout() returns
-ERESTARTSYS, and the SPI transfer in progress will fail, as expected:
m25p80 spi0.0: SPI transfer failed: -512
spi_master spi0: failed to transfer one message from queue
However, as the underlying DMA transfers may not have completed, all
subsequent SPI transfers may start to fail:
spi_master spi0: receive timeout
qspi_transfer_out_in() returned -110
m25p80 spi0.0: SPI transfer failed: -110
spi_master spi0: failed to transfer one message from queue
Fix this by calling dmaengine_terminate_all() not only for timeouts, but
also for errors.
This can be reproduced on r8a7991/koelsch, using "hd /dev/mtd0" followed
by CTRL-C.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Cc: [email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/spi/spi-rspi.c | 10 ++++++----
1 file changed, 6 insertions(+), 4 deletions(-)
--- a/drivers/spi/spi-rspi.c
+++ b/drivers/spi/spi-rspi.c
@@ -598,11 +598,13 @@ static int rspi_dma_transfer(struct rspi
ret = wait_event_interruptible_timeout(rspi->wait,
rspi->dma_callbacked, HZ);
- if (ret > 0 && rspi->dma_callbacked)
+ if (ret > 0 && rspi->dma_callbacked) {
ret = 0;
- else if (!ret) {
- dev_err(&rspi->master->dev, "DMA timeout\n");
- ret = -ETIMEDOUT;
+ } else {
+ if (!ret) {
+ dev_err(&rspi->master->dev, "DMA timeout\n");
+ ret = -ETIMEDOUT;
+ }
if (tx)
dmaengine_terminate_all(rspi->master->dma_tx);
if (rx)
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Brandon Maier <[email protected]>
[ Upstream commit 8d0752d11312be830c33e84dfd1016e6a47c2938 ]
We're ignoring the result of the attached phy device's read_status().
Return it so we can detect errors.
Signed-off-by: Brandon Maier <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/phy/xilinx_gmii2rgmii.c | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
--- a/drivers/net/phy/xilinx_gmii2rgmii.c
+++ b/drivers/net/phy/xilinx_gmii2rgmii.c
@@ -40,8 +40,11 @@ static int xgmiitorgmii_read_status(stru
{
struct gmii2rgmii *priv = phydev->priv;
u16 val = 0;
+ int err;
- priv->phy_drv->read_status(phydev);
+ err = priv->phy_drv->read_status(phydev);
+ if (err < 0)
+ return err;
val = mdiobus_read(phydev->mdio.bus, priv->addr, XILINX_GMII2RGMII_REG);
val &= ~XILINX_GMII2RGMII_SPEED_MASK;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Gaku Inami <[email protected]>
commit ffa69d6a16f686efe45269342474e421f2aa58b2 upstream.
If the SPI queue is running during system suspend, the system may lock
up.
Fix this by stopping/restarting the queue during system suspend/resume
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks. In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.
Signed-off-by: Gaku Inami <[email protected]>
Signed-off-by: Hiromitsu Yamasaki <[email protected]>
[geert: Cleanup, reword]
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Cc: [email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/spi/spi-sh-msiof.c | 25 +++++++++++++++++++++++++
1 file changed, 25 insertions(+)
--- a/drivers/spi/spi-sh-msiof.c
+++ b/drivers/spi/spi-sh-msiof.c
@@ -1361,12 +1361,37 @@ static const struct platform_device_id s
};
MODULE_DEVICE_TABLE(platform, spi_driver_ids);
+#ifdef CONFIG_PM_SLEEP
+static int sh_msiof_spi_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct sh_msiof_spi_priv *p = platform_get_drvdata(pdev);
+
+ return spi_master_suspend(p->master);
+}
+
+static int sh_msiof_spi_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct sh_msiof_spi_priv *p = platform_get_drvdata(pdev);
+
+ return spi_master_resume(p->master);
+}
+
+static SIMPLE_DEV_PM_OPS(sh_msiof_spi_pm_ops, sh_msiof_spi_suspend,
+ sh_msiof_spi_resume);
+#define DEV_PM_OPS &sh_msiof_spi_pm_ops
+#else
+#define DEV_PM_OPS NULL
+#endif /* CONFIG_PM_SLEEP */
+
static struct platform_driver sh_msiof_spi_drv = {
.probe = sh_msiof_spi_probe,
.remove = sh_msiof_spi_remove,
.id_table = spi_driver_ids,
.driver = {
.name = "spi_sh_msiof",
+ .pm = DEV_PM_OPS,
.of_match_table = of_match_ptr(sh_msiof_match),
},
};
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Hiromitsu Yamasaki <[email protected]>
commit 31a5fae4c5a009898da6d177901d5328051641ff upstream.
This patch changes writing to the SISTR register according to the H/W
user's manual.
The TDREQ bit and RDREQ bits of SISTR are read-only, and must be written
their initial values of zero.
Signed-off-by: Hiromitsu Yamasaki <[email protected]>
[geert: reword]
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Cc: [email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/spi/spi-sh-msiof.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
--- a/drivers/spi/spi-sh-msiof.c
+++ b/drivers/spi/spi-sh-msiof.c
@@ -384,7 +384,8 @@ static void sh_msiof_spi_set_mode_regs(s
static void sh_msiof_reset_str(struct sh_msiof_spi_priv *p)
{
- sh_msiof_write(p, STR, sh_msiof_read(p, STR));
+ sh_msiof_write(p, STR,
+ sh_msiof_read(p, STR) & ~(STR_TDREQ | STR_RDREQ));
}
static void sh_msiof_spi_write_fifo_8(struct sh_msiof_spi_priv *p,
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Alexander Shishkin <[email protected]>
commit 8801922cd94c918e4dc3a108ecaa500c4d40583f upstream.
Commit a753bfcfdb1f ("intel_th: Make the switch allocate its subdevices")
brings in new subdevice addition/removal logic that's broken for "host
mode": the SWITCH device has no children to begin with, which is not
handled in the code. This results in a null dereference bug later down
the path.
This patch fixes the subdevice removal code to handle host mode correctly.
Signed-off-by: Alexander Shishkin <[email protected]>
Fixes: a753bfcfdb1f ("intel_th: Make the switch allocate its subdevices")
CC: [email protected] # v4.14+
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/hwtracing/intel_th/core.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
--- a/drivers/hwtracing/intel_th/core.c
+++ b/drivers/hwtracing/intel_th/core.c
@@ -147,7 +147,8 @@ static int intel_th_remove(struct device
th->thdev[i] = NULL;
}
- th->num_thdevs = lowest;
+ if (lowest >= 0)
+ th->num_thdevs = lowest;
}
if (thdrv->attr_group)
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Christophe Leroy <[email protected]>
commit be28c1e3ca29887e207f0cbcd294cefe5074bab6 upstream.
kgdb expects poll function to return immediately and
returning NO_POLL_CHAR when no character is available.
Fixes: f5316b4aea024 ("kgdb,8250,pl011: Return immediately from console poll")
Cc: Jason Wessel <[email protected]>
Cc: <[email protected]>
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/tty/serial/cpm_uart/cpm_uart_core.c | 10 +++++++---
1 file changed, 7 insertions(+), 3 deletions(-)
--- a/drivers/tty/serial/cpm_uart/cpm_uart_core.c
+++ b/drivers/tty/serial/cpm_uart/cpm_uart_core.c
@@ -1068,8 +1068,8 @@ static int poll_wait_key(char *obuf, str
/* Get the address of the host memory buffer.
*/
bdp = pinfo->rx_cur;
- while (bdp->cbd_sc & BD_SC_EMPTY)
- ;
+ if (bdp->cbd_sc & BD_SC_EMPTY)
+ return NO_POLL_CHAR;
/* If the buffer address is in the CPM DPRAM, don't
* convert it.
@@ -1104,7 +1104,11 @@ static int cpm_get_poll_char(struct uart
poll_chars = 0;
}
if (poll_chars <= 0) {
- poll_chars = poll_wait_key(poll_buf, pinfo);
+ int ret = poll_wait_key(poll_buf, pinfo);
+
+ if (ret == NO_POLL_CHAR)
+ return ret;
+ poll_chars = ret;
pollp = poll_buf;
}
poll_chars--;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Stefan Agner <[email protected]>
commit 3216c622a24b0ebb9c159a8d1daf7f17a106b3f5 upstream.
The function tty_port_tty_get() gets a reference to the tty. Since
the code is not using tty_port_tty_set(), the reference is kept
even after closing the tty.
Avoid using tty_port_tty_get() by directly access the tty instance.
Since lpuart_start_rx_dma() is called from the .startup() and
.set_termios() callback, it is safe to assume the tty instance is
valid.
Cc: [email protected] # v4.9+
Fixes: 5887ad43ee02 ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Signed-off-by: Stefan Agner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/tty/serial/fsl_lpuart.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -983,7 +983,8 @@ static inline int lpuart_start_rx_dma(st
struct circ_buf *ring = &sport->rx_ring;
int ret, nent;
int bits, baud;
- struct tty_struct *tty = tty_port_tty_get(&sport->port.state->port);
+ struct tty_port *port = &sport->port.state->port;
+ struct tty_struct *tty = port->tty;
struct ktermios *termios = &tty->termios;
baud = tty_get_baud_rate(tty);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Andy Whitcroft <[email protected]>
commit 65eea8edc315589d6c993cf12dbb5d0e9ef1fe4e upstream.
The final field of a floppy_struct is the field "name", which is a pointer
to a string in kernel memory. The kernel pointer should not be copied to
user memory. The FDGETPRM ioctl copies a floppy_struct to user memory,
including this "name" field. This pointer cannot be used by the user
and it will leak a kernel address to user-space, which will reveal the
location of kernel code and data and undermine KASLR protection.
Model this code after the compat ioctl which copies the returned data
to a previously cleared temporary structure on the stack (excluding the
name pointer) and copy out to userspace from there. As we already have
an inparam union with an appropriate member and that memory is already
cleared even for read only calls make use of that as a temporary store.
Based on an initial patch by Brian Belleville.
CVE-2018-7755
Signed-off-by: Andy Whitcroft <[email protected]>
Broke up long line.
Signed-off-by: Jens Axboe <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/block/floppy.c | 3 +++
1 file changed, 3 insertions(+)
--- a/drivers/block/floppy.c
+++ b/drivers/block/floppy.c
@@ -3462,6 +3462,9 @@ static int fd_locked_ioctl(struct block_
(struct floppy_struct **)&outparam);
if (ret)
return ret;
+ memcpy(&inparam.g, outparam,
+ offsetof(struct floppy_struct, name));
+ outparam = &inparam.g;
break;
case FDMSGON:
UDP->flags |= FTD_MSG;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Geert Uytterhoeven <[email protected]>
commit c1ca59c22c56930b377a665fdd1b43351887830b upstream.
If the SPI queue is running during system suspend, the system may lock
up.
Fix this by stopping/restarting the queue during system suspend/resume,
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks. In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.
Based on a patch for sh-msiof by Gaku Inami.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Cc: [email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/spi/spi-rspi.c | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
--- a/drivers/spi/spi-rspi.c
+++ b/drivers/spi/spi-rspi.c
@@ -1352,12 +1352,36 @@ static const struct platform_device_id s
MODULE_DEVICE_TABLE(platform, spi_driver_ids);
+#ifdef CONFIG_PM_SLEEP
+static int rspi_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct rspi_data *rspi = platform_get_drvdata(pdev);
+
+ return spi_master_suspend(rspi->master);
+}
+
+static int rspi_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct rspi_data *rspi = platform_get_drvdata(pdev);
+
+ return spi_master_resume(rspi->master);
+}
+
+static SIMPLE_DEV_PM_OPS(rspi_pm_ops, rspi_suspend, rspi_resume);
+#define DEV_PM_OPS &rspi_pm_ops
+#else
+#define DEV_PM_OPS NULL
+#endif /* CONFIG_PM_SLEEP */
+
static struct platform_driver rspi_driver = {
.probe = rspi_probe,
.remove = rspi_remove,
.id_table = spi_driver_ids,
.driver = {
.name = "renesas_spi",
+ .pm = DEV_PM_OPS,
.of_match_table = of_match_ptr(rspi_of_match),
},
};
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Kai-Heng Feng <[email protected]>
[ Upstream commit 1adca4b0cd65c14cb8b8c9c257720385869c3d5f ]
This patch can make audio controller in AMD Raven Ridge gets runtime
suspended to D3, to save ~1W power when it's not in use.
Cc: Vijendar Mukunda <[email protected]>
Signed-off-by: Kai-Heng Feng <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/pci/hda/hda_intel.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
--- a/sound/pci/hda/hda_intel.c
+++ b/sound/pci/hda/hda_intel.c
@@ -2510,7 +2510,8 @@ static const struct pci_device_id azx_id
.driver_data = AZX_DRIVER_GENERIC | AZX_DCAPS_PRESET_ATI_SB },
/* AMD Raven */
{ PCI_DEVICE(0x1022, 0x15e3),
- .driver_data = AZX_DRIVER_GENERIC | AZX_DCAPS_PRESET_ATI_SB },
+ .driver_data = AZX_DRIVER_GENERIC | AZX_DCAPS_PRESET_ATI_SB |
+ AZX_DCAPS_PM_RUNTIME },
/* ATI HDMI */
{ PCI_DEVICE(0x1002, 0x0002),
.driver_data = AZX_DRIVER_ATIHDMI_NS | AZX_DCAPS_PRESET_ATI_HDMI_NS },
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Feng Tang <[email protected]>
commit 05ab1d8a4b36ee912b7087c6da127439ed0a903e upstream.
We met a kernel panic when enabling earlycon, which is due to the fixmap
address of earlycon is not statically setup.
Currently the static fixmap setup in head_64.S only covers 2M virtual
address space, while it actually could be in 4M space with different
kernel configurations, e.g. when VSYSCALL emulation is disabled.
So increase the static space to 4M for now by defining FIXMAP_PMD_NUM to 2,
and add a build time check to ensure that the fixmap is covered by the
initial static page tables.
Fixes: 1ad83c858c7d ("x86_64,vsyscall: Make vsyscall emulation configurable")
Suggested-by: Thomas Gleixner <[email protected]>
Signed-off-by: Feng Tang <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Tested-by: kernel test robot <[email protected]>
Reviewed-by: Juergen Gross <[email protected]> (Xen parts)
Cc: H Peter Anvin <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Michal Hocko <[email protected]>
Cc: Yinghai Lu <[email protected]>
Cc: Dave Hansen <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Andy Lutomirsky <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/x86/include/asm/fixmap.h | 10 ++++++++++
arch/x86/include/asm/pgtable_64.h | 3 ++-
arch/x86/kernel/head64.c | 4 +++-
arch/x86/kernel/head_64.S | 16 ++++++++++++----
arch/x86/mm/pgtable.c | 9 +++++++++
arch/x86/xen/mmu_pv.c | 8 ++++++--
6 files changed, 42 insertions(+), 8 deletions(-)
--- a/arch/x86/include/asm/fixmap.h
+++ b/arch/x86/include/asm/fixmap.h
@@ -14,6 +14,16 @@
#ifndef _ASM_X86_FIXMAP_H
#define _ASM_X86_FIXMAP_H
+/*
+ * Exposed to assembly code for setting up initial page tables. Cannot be
+ * calculated in assembly code (fixmap entries are an enum), but is sanity
+ * checked in the actual fixmap C code to make sure that the fixmap is
+ * covered fully.
+ */
+#define FIXMAP_PMD_NUM 2
+/* fixmap starts downwards from the 507th entry in level2_fixmap_pgt */
+#define FIXMAP_PMD_TOP 507
+
#ifndef __ASSEMBLY__
#include <linux/kernel.h>
#include <asm/acpi.h>
--- a/arch/x86/include/asm/pgtable_64.h
+++ b/arch/x86/include/asm/pgtable_64.h
@@ -14,6 +14,7 @@
#include <asm/processor.h>
#include <linux/bitops.h>
#include <linux/threads.h>
+#include <asm/fixmap.h>
extern p4d_t level4_kernel_pgt[512];
extern p4d_t level4_ident_pgt[512];
@@ -22,7 +23,7 @@ extern pud_t level3_ident_pgt[512];
extern pmd_t level2_kernel_pgt[512];
extern pmd_t level2_fixmap_pgt[512];
extern pmd_t level2_ident_pgt[512];
-extern pte_t level1_fixmap_pgt[512];
+extern pte_t level1_fixmap_pgt[512 * FIXMAP_PMD_NUM];
extern pgd_t init_top_pgt[];
#define swapper_pg_dir init_top_pgt
--- a/arch/x86/kernel/head64.c
+++ b/arch/x86/kernel/head64.c
@@ -31,6 +31,7 @@
#include <asm/bootparam_utils.h>
#include <asm/microcode.h>
#include <asm/kasan.h>
+#include <asm/fixmap.h>
/*
* Manage page tables very early on.
@@ -93,7 +94,8 @@ unsigned long __head __startup_64(unsign
pud[511] += load_delta;
pmd = fixup_pointer(level2_fixmap_pgt, physaddr);
- pmd[506] += load_delta;
+ for (i = FIXMAP_PMD_TOP; i > FIXMAP_PMD_TOP - FIXMAP_PMD_NUM; i--)
+ pmd[i] += load_delta;
/*
* Set up the identity mapping for the switchover. These
--- a/arch/x86/kernel/head_64.S
+++ b/arch/x86/kernel/head_64.S
@@ -24,6 +24,7 @@
#include "../entry/calling.h"
#include <asm/export.h>
#include <asm/nospec-branch.h>
+#include <asm/fixmap.h>
#ifdef CONFIG_PARAVIRT
#include <asm/asm-offsets.h>
@@ -438,13 +439,20 @@ NEXT_PAGE(level2_kernel_pgt)
KERNEL_IMAGE_SIZE/PMD_SIZE)
NEXT_PAGE(level2_fixmap_pgt)
- .fill 506,8,0
- .quad level1_fixmap_pgt - __START_KERNEL_map + _PAGE_TABLE_NOENC
- /* 8MB reserved for vsyscalls + a 2MB hole = 4 + 1 entries */
- .fill 5,8,0
+ .fill (512 - 4 - FIXMAP_PMD_NUM),8,0
+ pgtno = 0
+ .rept (FIXMAP_PMD_NUM)
+ .quad level1_fixmap_pgt + (pgtno << PAGE_SHIFT) - __START_KERNEL_map \
+ + _PAGE_TABLE_NOENC;
+ pgtno = pgtno + 1
+ .endr
+ /* 6 MB reserved space + a 2MB hole */
+ .fill 4,8,0
NEXT_PAGE(level1_fixmap_pgt)
+ .rept (FIXMAP_PMD_NUM)
.fill 512,8,0
+ .endr
#undef PMDS
--- a/arch/x86/mm/pgtable.c
+++ b/arch/x86/mm/pgtable.c
@@ -573,6 +573,15 @@ void __native_set_fixmap(enum fixed_addr
{
unsigned long address = __fix_to_virt(idx);
+#ifdef CONFIG_X86_64
+ /*
+ * Ensure that the static initial page tables are covering the
+ * fixmap completely.
+ */
+ BUILD_BUG_ON(__end_of_permanent_fixed_addresses >
+ (FIXMAP_PMD_NUM * PTRS_PER_PTE));
+#endif
+
if (idx >= __end_of_fixed_addresses) {
BUG();
return;
--- a/arch/x86/xen/mmu_pv.c
+++ b/arch/x86/xen/mmu_pv.c
@@ -1879,7 +1879,7 @@ void __init xen_setup_kernel_pagetable(p
/* L3_k[511] -> level2_fixmap_pgt */
convert_pfn_mfn(level3_kernel_pgt);
- /* L3_k[511][506] -> level1_fixmap_pgt */
+ /* L3_k[511][508-FIXMAP_PMD_NUM ... 507] -> level1_fixmap_pgt */
convert_pfn_mfn(level2_fixmap_pgt);
/* We get [511][511] and have Xen's version of level2_kernel_pgt */
@@ -1924,7 +1924,11 @@ void __init xen_setup_kernel_pagetable(p
set_page_prot(level2_ident_pgt, PAGE_KERNEL_RO);
set_page_prot(level2_kernel_pgt, PAGE_KERNEL_RO);
set_page_prot(level2_fixmap_pgt, PAGE_KERNEL_RO);
- set_page_prot(level1_fixmap_pgt, PAGE_KERNEL_RO);
+
+ for (i = 0; i < FIXMAP_PMD_NUM; i++) {
+ set_page_prot(level1_fixmap_pgt + i * PTRS_PER_PTE,
+ PAGE_KERNEL_RO);
+ }
/* Pin down new L4 */
pin_pagetable_pfn(MMUEXT_PIN_L4_TABLE,
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Kevin Hilman <[email protected]>
[ Upstream commit 949bdcc8a97c6078f21c8d4966436b117f2e4cd3 ]
Fix the DT node addresses to match the reg property addresses,
which were verified to match the TRM:
http://www.ti.com/lit/pdf/sprui30
Cc: Roger Quadros <[email protected]>
Signed-off-by: Kevin Hilman <[email protected]>
Acked-by: Roger Quadros <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/arm/boot/dts/dra7.dtsi | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -1818,7 +1818,7 @@
};
};
- dcan1: can@481cc000 {
+ dcan1: can@4ae3c000 {
compatible = "ti,dra7-d_can";
ti,hwmods = "dcan1";
reg = <0x4ae3c000 0x2000>;
@@ -1828,7 +1828,7 @@
status = "disabled";
};
- dcan2: can@481d0000 {
+ dcan2: can@48480000 {
compatible = "ti,dra7-d_can";
ti,hwmods = "dcan2";
reg = <0x48480000 0x2000>;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: William Breathitt Gray <[email protected]>
[ Upstream commit 2873c3f0e2bd12a7612e905c920c058855f4072a ]
The reset flags operation is selected by bit 2 in the "Reset and Load
Signals Decoders" register, not bit 1.
Fixes: 28e5d3bb0325 ("iio: 104-quad-8: Add IIO support for the ACCES 104-QUAD-8")
Signed-off-by: William Breathitt Gray <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/iio/counter/104-quad-8.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/iio/counter/104-quad-8.c
+++ b/drivers/iio/counter/104-quad-8.c
@@ -138,7 +138,7 @@ static int quad8_write_raw(struct iio_de
outb(val >> (8 * i), base_offset);
/* Reset Borrow, Carry, Compare, and Sign flags */
- outb(0x02, base_offset + 1);
+ outb(0x04, base_offset + 1);
/* Reset Error flag */
outb(0x06, base_offset + 1);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Konstantin Khorenko <[email protected]>
[ Upstream commit 826d7bc9f013d01e92997883d2fd0c25f4af1f1c ]
If the flock owner process is dead and its pid has been already freed,
pid translation won't work, but we still want to show flock owner pid
number when expecting /proc/$PID/fdinfo/$FD in init pidns.
Reproducer:
process A process A1 process A2
fork()--------->
exit() open()
flock()
fork()--------->
exit() sleep()
Before the patch:
================
(root@vz7)/: cat /proc/${PID_A2}/fdinfo/3
pos: 4
flags: 02100002
mnt_id: 257
lock: (root@vz7)/:
After the patch:
===============
(root@vz7)/:cat /proc/${PID_A2}/fdinfo/3
pos: 4
flags: 02100002
mnt_id: 295
lock: 1: FLOCK ADVISORY WRITE ${PID_A1} b6:f8a61:529946 0 EOF
Fixes: 9d5b86ac13c5 ("fs/locks: Remove fl_nspid and use fs-specific l_pid for remote locks")
Signed-off-by: Konstantin Khorenko <[email protected]>
Acked-by: Andrey Vagin <[email protected]>
Reviewed-by: Benjamin Coddington <[email protected]>
Signed-off-by: Jeff Layton <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/locks.c | 7 +++++++
1 file changed, 7 insertions(+)
--- a/fs/locks.c
+++ b/fs/locks.c
@@ -2074,6 +2074,13 @@ static pid_t locks_translate_pid(struct
return -1;
if (IS_REMOTELCK(fl))
return fl->fl_pid;
+ /*
+ * If the flock owner process is dead and its pid has been already
+ * freed, the translation below won't work, but we still want to show
+ * flock owner pid number in init pidns.
+ */
+ if (ns == &init_pid_ns)
+ return (pid_t)fl->fl_pid;
rcu_read_lock();
pid = find_pid_ns(fl->fl_pid, &init_pid_ns);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Oleksandr Andrushchenko <[email protected]>
[ Upstream commit ce6f7d087e2b037f47349c1c36ac97678d02e394 ]
kbdif protocol describes multi-touch device parameters as a
part of frontend's XenBus configuration nodes while they
belong to backend's configuration. Fix this by reading the
parameters as defined by the protocol.
Fixes: 49aac8204da5 ("Input: xen-kbdfront - add multi-touch support")
Signed-off-by: Oleksandr Andrushchenko <[email protected]>
Reviewed-by: Juergen Gross <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/input/misc/xen-kbdfront.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
--- a/drivers/input/misc/xen-kbdfront.c
+++ b/drivers/input/misc/xen-kbdfront.c
@@ -229,7 +229,7 @@ static int xenkbd_probe(struct xenbus_de
}
}
- touch = xenbus_read_unsigned(dev->nodename,
+ touch = xenbus_read_unsigned(dev->otherend,
XENKBD_FIELD_FEAT_MTOUCH, 0);
if (touch) {
ret = xenbus_write(XBT_NIL, dev->nodename,
@@ -304,13 +304,13 @@ static int xenkbd_probe(struct xenbus_de
if (!mtouch)
goto error_nomem;
- num_cont = xenbus_read_unsigned(info->xbdev->nodename,
+ num_cont = xenbus_read_unsigned(info->xbdev->otherend,
XENKBD_FIELD_MT_NUM_CONTACTS,
1);
- width = xenbus_read_unsigned(info->xbdev->nodename,
+ width = xenbus_read_unsigned(info->xbdev->otherend,
XENKBD_FIELD_MT_WIDTH,
XENFB_WIDTH);
- height = xenbus_read_unsigned(info->xbdev->nodename,
+ height = xenbus_read_unsigned(info->xbdev->otherend,
XENKBD_FIELD_MT_HEIGHT,
XENFB_HEIGHT);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Yu Zhao <[email protected]>
commit fb6de923ca3358a91525552b4907d4cb38730bdd upstream.
dev_set_drvdata() needs to be called before device_register()
exposes device to userspace. Otherwise kernel crashes after it
gets null pointer from dev_get_drvdata() when userspace tries
to access sysfs entries.
[Removed backtrace for length -- broonie]
Signed-off-by: Yu Zhao <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Cc: [email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/regulator/core.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/regulator/core.c
+++ b/drivers/regulator/core.c
@@ -4115,13 +4115,13 @@ regulator_register(const struct regulato
!rdev->desc->fixed_uV)
rdev->is_switch = true;
+ dev_set_drvdata(&rdev->dev, rdev);
ret = device_register(&rdev->dev);
if (ret != 0) {
put_device(&rdev->dev);
goto unset_supplies;
}
- dev_set_drvdata(&rdev->dev, rdev);
rdev_init_debugfs(rdev);
/* try to resolve regulators supply since a new one was registered */
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: "J. Bruce Fields" <[email protected]>
[ Upstream commit 5b7b15aee641904ae269be9846610a3950cbd64c ]
We're encoding a single op in the reply but leaving the number of ops
zero, so the reply makes no sense.
Somewhat academic as this isn't a case any real client will hit, though
in theory perhaps that could change in a future protocol extension.
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: J. Bruce Fields <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/nfsd/nfs4proc.c | 1 +
1 file changed, 1 insertion(+)
--- a/fs/nfsd/nfs4proc.c
+++ b/fs/nfsd/nfs4proc.c
@@ -1725,6 +1725,7 @@ nfsd4_proc_compound(struct svc_rqst *rqs
if (status) {
op = &args->ops[0];
op->status = status;
+ resp->opcnt = 1;
goto encode_op;
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Jessica Yu <[email protected]>
[ Upstream commit 9f2d1e68cf4d641def734adaccfc3823d3575e6c ]
Livepatch modules are special in that we preserve their entire symbol
tables in order to be able to apply relocations after module load. The
unwanted side effect of this is that undefined (SHN_UNDEF) symbols of
livepatch modules are accessible via the kallsyms api and this can
confuse symbol resolution in livepatch (klp_find_object_symbol()) and
cause subtle bugs in livepatch.
Have the module kallsyms api skip over SHN_UNDEF symbols. These symbols
are usually not available for normal modules anyway as we cut down their
symbol tables to just the core (non-undefined) symbols, so this should
really just affect livepatch modules. Note that this patch doesn't
affect the display of undefined symbols in /proc/kallsyms.
Reported-by: Josh Poimboeuf <[email protected]>
Tested-by: Josh Poimboeuf <[email protected]>
Reviewed-by: Josh Poimboeuf <[email protected]>
Signed-off-by: Jessica Yu <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
kernel/module.c | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
--- a/kernel/module.c
+++ b/kernel/module.c
@@ -4058,7 +4058,7 @@ static unsigned long mod_find_symname(st
for (i = 0; i < kallsyms->num_symtab; i++)
if (strcmp(name, symname(kallsyms, i)) == 0 &&
- kallsyms->symtab[i].st_info != 'U')
+ kallsyms->symtab[i].st_shndx != SHN_UNDEF)
return kallsyms->symtab[i].st_value;
return 0;
}
@@ -4104,6 +4104,10 @@ int module_kallsyms_on_each_symbol(int (
if (mod->state == MODULE_STATE_UNFORMED)
continue;
for (i = 0; i < kallsyms->num_symtab; i++) {
+
+ if (kallsyms->symtab[i].st_shndx == SHN_UNDEF)
+ continue;
+
ret = fn(data, symname(kallsyms, i),
mod, kallsyms->symtab[i].st_value);
if (ret != 0)
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Nadav Amit <[email protected]>
[ Upstream commit 7279d9917560bbd0d82813d6bf00490a82c06783 ]
men_z127_debounce() tries to round up and down, but uses functions which
are only suitable when the divider is a power of two, which is not the
case. Use the appropriate ones.
Found by static check. Compile tested.
Fixes: f436bc2726c64 ("gpio: add driver for MEN 16Z127 GPIO controller")
Signed-off-by: Nadav Amit <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/gpio/gpio-menz127.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/drivers/gpio/gpio-menz127.c
+++ b/drivers/gpio/gpio-menz127.c
@@ -56,9 +56,9 @@ static int men_z127_debounce(struct gpio
rnd = fls(debounce) - 1;
if (rnd && (debounce & BIT(rnd - 1)))
- debounce = round_up(debounce, MEN_Z127_DB_MIN_US);
+ debounce = roundup(debounce, MEN_Z127_DB_MIN_US);
else
- debounce = round_down(debounce, MEN_Z127_DB_MIN_US);
+ debounce = rounddown(debounce, MEN_Z127_DB_MIN_US);
if (debounce > MEN_Z127_DB_MAX_US)
debounce = MEN_Z127_DB_MAX_US;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Marcel Ziswiler <[email protected]>
commit 7001cab1dabc0b72b2b672ef58a90ab64f5e2343 upstream.
Depending on the SPI instance one may get an interrupt storm upon
requesting resp. interrupt unless the clock is explicitly enabled
beforehand. This has been observed trying to bring up instance 4 on
T20.
Signed-off-by: Marcel Ziswiler <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Cc: [email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/spi/spi-tegra20-slink.c | 31 +++++++++++++++++++++++--------
1 file changed, 23 insertions(+), 8 deletions(-)
--- a/drivers/spi/spi-tegra20-slink.c
+++ b/drivers/spi/spi-tegra20-slink.c
@@ -1063,6 +1063,24 @@ static int tegra_slink_probe(struct plat
goto exit_free_master;
}
+ /* disabled clock may cause interrupt storm upon request */
+ tspi->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(tspi->clk)) {
+ ret = PTR_ERR(tspi->clk);
+ dev_err(&pdev->dev, "Can not get clock %d\n", ret);
+ goto exit_free_master;
+ }
+ ret = clk_prepare(tspi->clk);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Clock prepare failed %d\n", ret);
+ goto exit_free_master;
+ }
+ ret = clk_enable(tspi->clk);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Clock enable failed %d\n", ret);
+ goto exit_free_master;
+ }
+
spi_irq = platform_get_irq(pdev, 0);
tspi->irq = spi_irq;
ret = request_threaded_irq(tspi->irq, tegra_slink_isr,
@@ -1071,14 +1089,7 @@ static int tegra_slink_probe(struct plat
if (ret < 0) {
dev_err(&pdev->dev, "Failed to register ISR for IRQ %d\n",
tspi->irq);
- goto exit_free_master;
- }
-
- tspi->clk = devm_clk_get(&pdev->dev, NULL);
- if (IS_ERR(tspi->clk)) {
- dev_err(&pdev->dev, "can not get clock\n");
- ret = PTR_ERR(tspi->clk);
- goto exit_free_irq;
+ goto exit_clk_disable;
}
tspi->rst = devm_reset_control_get_exclusive(&pdev->dev, "spi");
@@ -1138,6 +1149,8 @@ exit_rx_dma_free:
tegra_slink_deinit_dma_param(tspi, true);
exit_free_irq:
free_irq(spi_irq, tspi);
+exit_clk_disable:
+ clk_disable(tspi->clk);
exit_free_master:
spi_master_put(master);
return ret;
@@ -1150,6 +1163,8 @@ static int tegra_slink_remove(struct pla
free_irq(tspi->irq, tspi);
+ clk_disable(tspi->clk);
+
if (tspi->tx_dma_chan)
tegra_slink_deinit_dma_param(tspi, false);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Liam Girdwood <[email protected]>
[ Upstream commit e01b4f624278d5efe5fb5da585ca371947b16680 ]
Sometime a component or topology may configure a DAI widget with no
private data leading to a dev_dbg() dereferencne of this data.
Fix this to check for non NULL private data and let users know if widget
is missing DAI.
Signed-off-by: Liam Girdwood <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/soc/soc-dapm.c | 7 +++++++
1 file changed, 7 insertions(+)
--- a/sound/soc/soc-dapm.c
+++ b/sound/soc/soc-dapm.c
@@ -4005,6 +4005,13 @@ int snd_soc_dapm_link_dai_widgets(struct
continue;
}
+ /* let users know there is no DAI to link */
+ if (!dai_w->priv) {
+ dev_dbg(card->dev, "dai widget %s has no DAI\n",
+ dai_w->name);
+ continue;
+ }
+
dai = dai_w->priv;
/* ...find all widgets with the same stream and link them */
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Johan Hovold <[email protected]>
[ Upstream commit 6c974d4dfafe5e9ee754f2a6fba0eb1864f1649e ]
Make sure to free and deregister the addrmatch and chancounts devices
allocated during probe in all error paths. Also fix use-after-free in a
probe error path and in the remove success path where the devices were
being put before before deregistration.
Signed-off-by: Johan Hovold <[email protected]>
Cc: Mauro Carvalho Chehab <[email protected]>
Cc: linux-edac <[email protected]>
Fixes: 356f0a30860d ("i7core_edac: change the mem allocation scheme to make Documentation/kobject.txt happy")
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Borislav Petkov <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/edac/i7core_edac.c | 22 +++++++++++++++-------
1 file changed, 15 insertions(+), 7 deletions(-)
--- a/drivers/edac/i7core_edac.c
+++ b/drivers/edac/i7core_edac.c
@@ -1177,15 +1177,14 @@ static int i7core_create_sysfs_devices(s
rc = device_add(pvt->addrmatch_dev);
if (rc < 0)
- return rc;
+ goto err_put_addrmatch;
if (!pvt->is_registered) {
pvt->chancounts_dev = kzalloc(sizeof(*pvt->chancounts_dev),
GFP_KERNEL);
if (!pvt->chancounts_dev) {
- put_device(pvt->addrmatch_dev);
- device_del(pvt->addrmatch_dev);
- return -ENOMEM;
+ rc = -ENOMEM;
+ goto err_del_addrmatch;
}
pvt->chancounts_dev->type = &all_channel_counts_type;
@@ -1199,9 +1198,18 @@ static int i7core_create_sysfs_devices(s
rc = device_add(pvt->chancounts_dev);
if (rc < 0)
- return rc;
+ goto err_put_chancounts;
}
return 0;
+
+err_put_chancounts:
+ put_device(pvt->chancounts_dev);
+err_del_addrmatch:
+ device_del(pvt->addrmatch_dev);
+err_put_addrmatch:
+ put_device(pvt->addrmatch_dev);
+
+ return rc;
}
static void i7core_delete_sysfs_devices(struct mem_ctl_info *mci)
@@ -1211,11 +1219,11 @@ static void i7core_delete_sysfs_devices(
edac_dbg(1, "\n");
if (!pvt->is_registered) {
- put_device(pvt->chancounts_dev);
device_del(pvt->chancounts_dev);
+ put_device(pvt->chancounts_dev);
}
- put_device(pvt->addrmatch_dev);
device_del(pvt->addrmatch_dev);
+ put_device(pvt->addrmatch_dev);
}
/****************************************************************************
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Zhouyang Jia <[email protected]>
[ Upstream commit e95d7c6eb94c634852eaa5ff4caf3db05b5d2e86 ]
When dvb_register_adapter fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling dvb_register_adapter.
Signed-off-by: Zhouyang Jia <[email protected]>
[[email protected]: use pr_err and fix typo: adater -> adapter]
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/media/usb/tm6000/tm6000-dvb.c | 5 +++++
1 file changed, 5 insertions(+)
--- a/drivers/media/usb/tm6000/tm6000-dvb.c
+++ b/drivers/media/usb/tm6000/tm6000-dvb.c
@@ -267,6 +267,11 @@ static int register_dvb(struct tm6000_co
ret = dvb_register_adapter(&dvb->adapter, "Trident TVMaster 6000 DVB-T",
THIS_MODULE, &dev->udev->dev, adapter_nr);
+ if (ret < 0) {
+ pr_err("tm6000: couldn't register the adapter!\n");
+ goto err;
+ }
+
dvb->adapter.priv = dev;
if (dvb->frontend) {
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Shivasharan S <[email protected]>
[ Upstream commit c3b10a55abc943a526aaecd7e860b15671beb906 ]
There is a possibility that firmware on the controller was upgraded before
system was suspended. During resume, driver needs to read updated
controller properties.
Signed-off-by: Shivasharan S <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/scsi/megaraid/megaraid_sas_base.c | 3 +++
1 file changed, 3 insertions(+)
--- a/drivers/scsi/megaraid/megaraid_sas_base.c
+++ b/drivers/scsi/megaraid/megaraid_sas_base.c
@@ -6597,6 +6597,9 @@ megasas_resume(struct pci_dev *pdev)
goto fail_init_mfi;
}
+ if (megasas_get_ctrl_info(instance) != DCMD_SUCCESS)
+ goto fail_init_mfi;
+
tasklet_init(&instance->isr_tasklet, instance->instancet->tasklet,
(unsigned long)instance);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Kan Liang <[email protected]>
[ Upstream commit 0592e57b24e7e05ec1f4c50b9666c013abff7017 ]
LBR has a limited stack size. If a task has a deeper call stack than
LBR's stack size, only the overflowed part is reported. A complete call
stack may not be reconstructed by perf tool.
Current code doesn't access all LBR registers. It only read the ones
below the TOS. The LBR registers above the TOS will be discarded
unconditionally.
When a CALL is captured, the TOS is incremented by 1 , modulo max LBR
stack size. The LBR HW only records the call stack information to the
register which the TOS points to. It will not touch other LBR
registers. So the registers above the TOS probably still store the valid
call stack information for an overflowed call stack, which need to be
reported.
To retrieve complete call stack information, we need to start from TOS,
read all LBR registers until an invalid entry is detected.
0s can be used to detect the invalid entry, because:
- When a RET is captured, the HW zeros the LBR register which TOS points
to, then decreases the TOS.
- The LBR registers are reset to 0 when adding a new LBR event or
scheduling an existing LBR event.
- A taken branch at IP 0 is not expected
The context switch code is also modified to save/restore all valid LBR
registers. Furthermore, the LBR registers, which don't have valid call
stack information, need to be reset in restore, because they may be
polluted while swapped out.
Here is a small test program, tchain_deep.
Its call stack is deeper than 32.
noinline void f33(void)
{
int i;
for (i = 0; i < 10000000;) {
if (i%2)
i++;
else
i++;
}
}
noinline void f32(void)
{
f33();
}
noinline void f31(void)
{
f32();
}
... ...
noinline void f1(void)
{
f2();
}
int main()
{
f1();
}
Here is the test result on SKX. The max stack size of SKX is 32.
Without the patch:
$ perf record -e cycles --call-graph lbr -- ./tchain_deep
$ perf report --stdio
#
# Children Self Command Shared Object Symbol
# ........ ........ ........... ................ .................
#
100.00% 99.99% tchain_deep tchain_deep [.] f33
|
--99.99%--f30
f31
f32
f33
With the patch:
$ perf record -e cycles --call-graph lbr -- ./tchain_deep
$ perf report --stdio
# Children Self Command Shared Object Symbol
# ........ ........ ........... ................ ..................
#
99.99% 0.00% tchain_deep tchain_deep [.] f1
|
---f1
f2
f3
f4
f5
f6
f7
f8
f9
f10
f11
f12
f13
f14
f15
f16
f17
f18
f19
f20
f21
f22
f23
f24
f25
f26
f27
f28
f29
f30
f31
f32
f33
Signed-off-by: Kan Liang <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Arnaldo Carvalho de Melo <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Stephane Eranian <[email protected]>
Cc: Vince Weaver <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Cc: [email protected]
Link: https://lore.kernel.org/lkml/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/x86/events/intel/lbr.c | 32 ++++++++++++++++++++++++++------
arch/x86/events/perf_event.h | 1 +
2 files changed, 27 insertions(+), 6 deletions(-)
--- a/arch/x86/events/intel/lbr.c
+++ b/arch/x86/events/intel/lbr.c
@@ -346,7 +346,7 @@ static void __intel_pmu_lbr_restore(stru
mask = x86_pmu.lbr_nr - 1;
tos = task_ctx->tos;
- for (i = 0; i < tos; i++) {
+ for (i = 0; i < task_ctx->valid_lbrs; i++) {
lbr_idx = (tos - i) & mask;
wrlbr_from(lbr_idx, task_ctx->lbr_from[i]);
wrlbr_to (lbr_idx, task_ctx->lbr_to[i]);
@@ -354,6 +354,15 @@ static void __intel_pmu_lbr_restore(stru
if (x86_pmu.intel_cap.lbr_format == LBR_FORMAT_INFO)
wrmsrl(MSR_LBR_INFO_0 + lbr_idx, task_ctx->lbr_info[i]);
}
+
+ for (; i < x86_pmu.lbr_nr; i++) {
+ lbr_idx = (tos - i) & mask;
+ wrlbr_from(lbr_idx, 0);
+ wrlbr_to(lbr_idx, 0);
+ if (x86_pmu.intel_cap.lbr_format == LBR_FORMAT_INFO)
+ wrmsrl(MSR_LBR_INFO_0 + lbr_idx, 0);
+ }
+
wrmsrl(x86_pmu.lbr_tos, tos);
task_ctx->lbr_stack_state = LBR_NONE;
}
@@ -361,7 +370,7 @@ static void __intel_pmu_lbr_restore(stru
static void __intel_pmu_lbr_save(struct x86_perf_task_context *task_ctx)
{
unsigned lbr_idx, mask;
- u64 tos;
+ u64 tos, from;
int i;
if (task_ctx->lbr_callstack_users == 0) {
@@ -371,13 +380,17 @@ static void __intel_pmu_lbr_save(struct
mask = x86_pmu.lbr_nr - 1;
tos = intel_pmu_lbr_tos();
- for (i = 0; i < tos; i++) {
+ for (i = 0; i < x86_pmu.lbr_nr; i++) {
lbr_idx = (tos - i) & mask;
- task_ctx->lbr_from[i] = rdlbr_from(lbr_idx);
+ from = rdlbr_from(lbr_idx);
+ if (!from)
+ break;
+ task_ctx->lbr_from[i] = from;
task_ctx->lbr_to[i] = rdlbr_to(lbr_idx);
if (x86_pmu.intel_cap.lbr_format == LBR_FORMAT_INFO)
rdmsrl(MSR_LBR_INFO_0 + lbr_idx, task_ctx->lbr_info[i]);
}
+ task_ctx->valid_lbrs = i;
task_ctx->tos = tos;
task_ctx->lbr_stack_state = LBR_VALID;
}
@@ -531,7 +544,7 @@ static void intel_pmu_lbr_read_32(struct
*/
static void intel_pmu_lbr_read_64(struct cpu_hw_events *cpuc)
{
- bool need_info = false;
+ bool need_info = false, call_stack = false;
unsigned long mask = x86_pmu.lbr_nr - 1;
int lbr_format = x86_pmu.intel_cap.lbr_format;
u64 tos = intel_pmu_lbr_tos();
@@ -542,7 +555,7 @@ static void intel_pmu_lbr_read_64(struct
if (cpuc->lbr_sel) {
need_info = !(cpuc->lbr_sel->config & LBR_NO_INFO);
if (cpuc->lbr_sel->config & LBR_CALL_STACK)
- num = tos;
+ call_stack = true;
}
for (i = 0; i < num; i++) {
@@ -555,6 +568,13 @@ static void intel_pmu_lbr_read_64(struct
from = rdlbr_from(lbr_idx);
to = rdlbr_to(lbr_idx);
+ /*
+ * Read LBR call stack entries
+ * until invalid entry (0s) is detected.
+ */
+ if (call_stack && !from)
+ break;
+
if (lbr_format == LBR_FORMAT_INFO && need_info) {
u64 info;
--- a/arch/x86/events/perf_event.h
+++ b/arch/x86/events/perf_event.h
@@ -646,6 +646,7 @@ struct x86_perf_task_context {
u64 lbr_to[MAX_LBR_ENTRIES];
u64 lbr_info[MAX_LBR_ENTRIES];
int tos;
+ int valid_lbrs;
int lbr_callstack_users;
int lbr_stack_state;
};
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Zhouyang Jia <[email protected]>
[ Upstream commit aa154ea885eb0c2407457ce9c1538d78c95456fa ]
When ioremap_nocache fails, the lack of error-handling code may cause
unexpected results.
This patch adds error-handling code after calling ioremap_nocache.
Signed-off-by: Zhouyang Jia <[email protected]>
Reviewed-by: Johannes Thumshirn <[email protected]>
Acked-by: Manish Rangankar <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/scsi/bnx2i/bnx2i_hwi.c | 2 ++
1 file changed, 2 insertions(+)
--- a/drivers/scsi/bnx2i/bnx2i_hwi.c
+++ b/drivers/scsi/bnx2i/bnx2i_hwi.c
@@ -2742,6 +2742,8 @@ int bnx2i_map_ep_dbell_regs(struct bnx2i
BNX2X_DOORBELL_PCI_BAR);
reg_off = (1 << BNX2X_DB_SHIFT) * (cid_num & 0x1FFFF);
ep->qp.ctx_base = ioremap_nocache(reg_base + reg_off, 4);
+ if (!ep->qp.ctx_base)
+ return -ENOMEM;
goto arm_cq;
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Masahiro Yamada <[email protected]>
[ Upstream commit 67e09db507db3e1642ddce512a4313d20addd6e5 ]
As Documentation/kbuild/makefile.txt says, it is a typical mistake
to forget the FORCE prerequisite for the rule invoked by if_changed.
Add the FORCE to the prerequisite, but it must be filtered-out from
the files passed to the 'cat' command. Because this rule generates
.vmlinux.its.S.cmd, vmlinux.its.S must be specified as targets so
that the .cmd file is included.
Signed-off-by: Masahiro Yamada <[email protected]>
Patchwork: https://patchwork.linux-mips.org/patch/19097/
Signed-off-by: Paul Burton <[email protected]>
Cc: Kees Cook <[email protected]>
Cc: [email protected]
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/mips/boot/Makefile | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
--- a/arch/mips/boot/Makefile
+++ b/arch/mips/boot/Makefile
@@ -118,10 +118,12 @@ ifeq ($(ADDR_BITS),64)
itb_addr_cells = 2
endif
+targets += vmlinux.its.S
+
quiet_cmd_its_cat = CAT $@
- cmd_its_cat = cat $^ >$@
+ cmd_its_cat = cat $(filter-out $(PHONY), $^) >$@
-$(obj)/vmlinux.its.S: $(addprefix $(srctree)/arch/mips/$(PLATFORM)/,$(ITS_INPUTS))
+$(obj)/vmlinux.its.S: $(addprefix $(srctree)/arch/mips/$(PLATFORM)/,$(ITS_INPUTS)) FORCE
$(call if_changed,its_cat)
quiet_cmd_cpp_its_S = ITS $@
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Viresh Kumar <[email protected]>
[ Upstream commit 0c7f7a5150023f3c6f0b27c4d4940ce3dfaf62cc ]
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/arm/boot/dts/mt7623.dtsi | 3 +++
1 file changed, 3 insertions(+)
--- a/arch/arm/boot/dts/mt7623.dtsi
+++ b/arch/arm/boot/dts/mt7623.dtsi
@@ -98,6 +98,7 @@
compatible = "arm,cortex-a7";
reg = <0x1>;
operating-points-v2 = <&cpu_opp_table>;
+ #cooling-cells = <2>;
clock-frequency = <1300000000>;
};
@@ -106,6 +107,7 @@
compatible = "arm,cortex-a7";
reg = <0x2>;
operating-points-v2 = <&cpu_opp_table>;
+ #cooling-cells = <2>;
clock-frequency = <1300000000>;
};
@@ -114,6 +116,7 @@
compatible = "arm,cortex-a7";
reg = <0x3>;
operating-points-v2 = <&cpu_opp_table>;
+ #cooling-cells = <2>;
clock-frequency = <1300000000>;
};
};
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Andreas Gruenbacher <[email protected]>
[ Upstream commit ebf00be37de35788cad72f4f20b4a39e30c0be4a ]
According to xfstest generic/240, applications seem to expect direct I/O
writes to either complete as a whole or to fail; short direct I/O writes
are apparently not appreciated. This means that when only part of an
asynchronous direct I/O write succeeds, we can either fail the entire
write, or we can wait for the partial write to complete and retry the
remaining write as buffered I/O. The old __blockdev_direct_IO helper
has code for waiting for partial writes to complete; the new
iomap_dio_rw iomap helper does not.
The above mentioned fallback mode is needed for gfs2, which doesn't
allow block allocations under direct I/O to avoid taking cluster-wide
exclusive locks. As a consequence, an asynchronous direct I/O write to
a file range that contains a hole will result in a short write. In that
case, wait for the short write to complete to allow gfs2 to recover.
Signed-off-by: Andreas Gruenbacher <[email protected]>
Signed-off-by: Christoph Hellwig <[email protected]>
Reviewed-by: Darrick J. Wong <[email protected]>
Signed-off-by: Darrick J. Wong <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/iomap.c | 21 +++++++++++----------
1 file changed, 11 insertions(+), 10 deletions(-)
--- a/fs/iomap.c
+++ b/fs/iomap.c
@@ -693,6 +693,7 @@ struct iomap_dio {
atomic_t ref;
unsigned flags;
int error;
+ bool wait_for_completion;
union {
/* used during submission and for synchronous completion: */
@@ -793,9 +794,8 @@ static void iomap_dio_bio_end_io(struct
iomap_dio_set_error(dio, blk_status_to_errno(bio->bi_status));
if (atomic_dec_and_test(&dio->ref)) {
- if (is_sync_kiocb(dio->iocb)) {
+ if (dio->wait_for_completion) {
struct task_struct *waiter = dio->submit.waiter;
-
WRITE_ONCE(dio->submit.waiter, NULL);
wake_up_process(waiter);
} else if (dio->flags & IOMAP_DIO_WRITE) {
@@ -980,13 +980,12 @@ iomap_dio_rw(struct kiocb *iocb, struct
dio->end_io = end_io;
dio->error = 0;
dio->flags = 0;
+ dio->wait_for_completion = is_sync_kiocb(iocb);
dio->submit.iter = iter;
- if (is_sync_kiocb(iocb)) {
- dio->submit.waiter = current;
- dio->submit.cookie = BLK_QC_T_NONE;
- dio->submit.last_queue = NULL;
- }
+ dio->submit.waiter = current;
+ dio->submit.cookie = BLK_QC_T_NONE;
+ dio->submit.last_queue = NULL;
if (iov_iter_rw(iter) == READ) {
if (pos >= dio->i_size)
@@ -1016,7 +1015,7 @@ iomap_dio_rw(struct kiocb *iocb, struct
WARN_ON_ONCE(ret);
ret = 0;
- if (iov_iter_rw(iter) == WRITE && !is_sync_kiocb(iocb) &&
+ if (iov_iter_rw(iter) == WRITE && !dio->wait_for_completion &&
!inode->i_sb->s_dio_done_wq) {
ret = sb_init_dio_done_wq(inode->i_sb);
if (ret < 0)
@@ -1031,8 +1030,10 @@ iomap_dio_rw(struct kiocb *iocb, struct
iomap_dio_actor);
if (ret <= 0) {
/* magic error code to fall back to buffered I/O */
- if (ret == -ENOTBLK)
+ if (ret == -ENOTBLK) {
+ dio->wait_for_completion = true;
ret = 0;
+ }
break;
}
pos += ret;
@@ -1046,7 +1047,7 @@ iomap_dio_rw(struct kiocb *iocb, struct
iomap_dio_set_error(dio, ret);
if (!atomic_dec_and_test(&dio->ref)) {
- if (!is_sync_kiocb(iocb))
+ if (!dio->wait_for_completion)
return -EIOCBQUEUED;
for (;;) {
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Vasily Gorbik <[email protected]>
[ Upstream commit 5bedf8aa03c28cb8dc98bdd32a41b66d8f7d3eaa ]
Since proc_dointvec does not perform value range control,
proc_dointvec_minmax should be used to limit value range, which is
clearly intended here, as the internal representation of the value:
unsigned int alloc_pgste:1;
In fact it currently works, since we have
mm->context.alloc_pgste = page_table_allocate_pgste || ...
... since commit 23fefe119ceb5 ("s390/kvm: avoid global config of vm.alloc_pgste=1")
Before that it was
mm->context.alloc_pgste = page_table_allocate_pgste;
which was broken. That was introduced with commit 0b46e0a3ec0d7 ("s390/kvm:
remove delayed reallocation of page tables for KVM").
Fixes: 0b46e0a3ec0d7 ("s390/kvm: remove delayed reallocation of page tables for KVM")
Acked-by: Christian Borntraeger <[email protected]>
Reviewed-by: Heiko Carstens <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
Signed-off-by: Martin Schwidefsky <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/s390/mm/pgalloc.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/arch/s390/mm/pgalloc.c
+++ b/arch/s390/mm/pgalloc.c
@@ -27,7 +27,7 @@ static struct ctl_table page_table_sysct
.data = &page_table_allocate_pgste,
.maxlen = sizeof(int),
.mode = S_IRUGO | S_IWUSR,
- .proc_handler = proc_dointvec,
+ .proc_handler = proc_dointvec_minmax,
.extra1 = &page_table_allocate_pgste_min,
.extra2 = &page_table_allocate_pgste_max,
},
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Javier Martinez Canillas <[email protected]>
[ Upstream commit 2ec7debd44b49927a6e2861521994cc075a389ed ]
The struct clk_init_data init variable is declared in the isp_xclk_init()
function so is an automatic variable allocated in the stack. But it's not
explicitly zero-initialized, so some init fields are left uninitialized.
This causes the data structure to have undefined values that may confuse
the common clock framework when the clock is registered.
For example, the uninitialized .flags field could have the CLK_IS_CRITICAL
bit set, causing the framework to wrongly prepare the clk on registration.
This leads to the isp_xclk_prepare() callback being called, which in turn
calls to the omap3isp_get() function that increments the isp dev refcount.
Since this omap3isp_get() call is unexpected, this leads to an unbalanced
omap3isp_get() call that prevents the requested IRQ to be later enabled,
due the refcount not being 0 when the correct omap3isp_get() call happens.
Fixes: 9b28ee3c9122 ("[media] omap3isp: Use the common clock framework")
Signed-off-by: Javier Martinez Canillas <[email protected]>
Reviewed-by: Sebastian Reichel <[email protected]>
Signed-off-by: Sakari Ailus <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/media/platform/omap3isp/isp.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/media/platform/omap3isp/isp.c
+++ b/drivers/media/platform/omap3isp/isp.c
@@ -305,7 +305,7 @@ static struct clk *isp_xclk_src_get(stru
static int isp_xclk_init(struct isp_device *isp)
{
struct device_node *np = isp->dev->of_node;
- struct clk_init_data init;
+ struct clk_init_data init = { 0 };
unsigned int i;
for (i = 0; i < ARRAY_SIZE(isp->xclks); ++i)
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Niklas Cassel <[email protected]>
[ Upstream commit 379521462e4add27f3514da8e4ab1fd7a54fe1c7 ]
Fixes the following splat during boot:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:747
in_atomic(): 1, irqs_disabled(): 128, pid: 77, name: kworker/2:1
4 locks held by kworker/2:1/77:
#0: (ptrval) ((wq_completion)"events"){+.+.}, at: process_one_work+0x1fc/0x8fc
#1: (ptrval) (deferred_probe_work){+.+.}, at: process_one_work+0x1fc/0x8fc
#2: (ptrval) (&dev->mutex){....}, at: __device_attach+0x40/0x178
#3: (ptrval) (msm_iommu_lock){....}, at: msm_iommu_add_device+0x28/0xcc
irq event stamp: 348
hardirqs last enabled at (347): [<c049dc18>] kfree+0xe0/0x3c0
hardirqs last disabled at (348): [<c0c35cac>] _raw_spin_lock_irqsave+0x2c/0x68
softirqs last enabled at (0): [<c0322fd8>] copy_process.part.5+0x280/0x1a68
softirqs last disabled at (0): [<00000000>] (null)
Preemption disabled at:
[<00000000>] (null)
CPU: 2 PID: 77 Comm: kworker/2:1 Not tainted 4.17.0-rc5-wt-ath-01075-gaca0516bb4cf #239
Hardware name: Generic DT based system
Workqueue: events deferred_probe_work_func
[<c0314e00>] (unwind_backtrace) from [<c030fc70>] (show_stack+0x20/0x24)
[<c030fc70>] (show_stack) from [<c0c16ad8>] (dump_stack+0xa0/0xcc)
[<c0c16ad8>] (dump_stack) from [<c035a978>] (___might_sleep+0x1f8/0x2d4)
ath10k_sdio mmc2:0001:1: Direct firmware load for ath10k/QCA9377/hw1.0/board-2.bin failed with error -2
[<c035a978>] (___might_sleep) from [<c035aac4>] (__might_sleep+0x70/0xa8)
[<c035aac4>] (__might_sleep) from [<c0c3066c>] (__mutex_lock+0x50/0xb28)
[<c0c3066c>] (__mutex_lock) from [<c0c31170>] (mutex_lock_nested+0x2c/0x34)
ath10k_sdio mmc2:0001:1: board_file api 1 bmi_id N/A crc32 544289f7
[<c0c31170>] (mutex_lock_nested) from [<c052d798>] (kernfs_find_and_get_ns+0x30/0x5c)
[<c052d798>] (kernfs_find_and_get_ns) from [<c0531cc8>] (sysfs_add_link_to_group+0x28/0x58)
[<c0531cc8>] (sysfs_add_link_to_group) from [<c07ef75c>] (iommu_device_link+0x50/0xb4)
[<c07ef75c>] (iommu_device_link) from [<c07f2288>] (msm_iommu_add_device+0xa0/0xcc)
[<c07f2288>] (msm_iommu_add_device) from [<c07ec6d0>] (add_iommu_group+0x3c/0x64)
[<c07ec6d0>] (add_iommu_group) from [<c07f9d40>] (bus_for_each_dev+0x84/0xc4)
[<c07f9d40>] (bus_for_each_dev) from [<c07ec7c8>] (bus_set_iommu+0xd0/0x10c)
[<c07ec7c8>] (bus_set_iommu) from [<c07f1a68>] (msm_iommu_probe+0x5b8/0x66c)
[<c07f1a68>] (msm_iommu_probe) from [<c07feaa8>] (platform_drv_probe+0x60/0xbc)
[<c07feaa8>] (platform_drv_probe) from [<c07fc1fc>] (driver_probe_device+0x30c/0x4cc)
[<c07fc1fc>] (driver_probe_device) from [<c07fc59c>] (__device_attach_driver+0xac/0x14c)
[<c07fc59c>] (__device_attach_driver) from [<c07f9e14>] (bus_for_each_drv+0x68/0xc8)
[<c07f9e14>] (bus_for_each_drv) from [<c07fbd3c>] (__device_attach+0xe4/0x178)
[<c07fbd3c>] (__device_attach) from [<c07fc698>] (device_initial_probe+0x1c/0x20)
[<c07fc698>] (device_initial_probe) from [<c07faee8>] (bus_probe_device+0x98/0xa0)
[<c07faee8>] (bus_probe_device) from [<c07fb4f4>] (deferred_probe_work_func+0x74/0x198)
[<c07fb4f4>] (deferred_probe_work_func) from [<c0348eb4>] (process_one_work+0x2c4/0x8fc)
[<c0348eb4>] (process_one_work) from [<c03497b0>] (worker_thread+0x2c4/0x5cc)
[<c03497b0>] (worker_thread) from [<c0350d10>] (kthread+0x180/0x188)
[<c0350d10>] (kthread) from [<c03010b4>] (ret_from_fork+0x14/0x20)
Fixes: 42df43b36163 ("iommu/msm: Make use of iommu_device_register interface")
Signed-off-by: Niklas Cassel <[email protected]>
Reviewed-by: Vivek Gautam <[email protected]>
Signed-off-by: Joerg Roedel <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/iommu/msm_iommu.c | 16 +++++-----------
1 file changed, 5 insertions(+), 11 deletions(-)
--- a/drivers/iommu/msm_iommu.c
+++ b/drivers/iommu/msm_iommu.c
@@ -395,20 +395,15 @@ static int msm_iommu_add_device(struct d
struct msm_iommu_dev *iommu;
struct iommu_group *group;
unsigned long flags;
- int ret = 0;
spin_lock_irqsave(&msm_iommu_lock, flags);
-
iommu = find_iommu_for_dev(dev);
+ spin_unlock_irqrestore(&msm_iommu_lock, flags);
+
if (iommu)
iommu_device_link(&iommu->iommu, dev);
else
- ret = -ENODEV;
-
- spin_unlock_irqrestore(&msm_iommu_lock, flags);
-
- if (ret)
- return ret;
+ return -ENODEV;
group = iommu_group_get_for_dev(dev);
if (IS_ERR(group))
@@ -425,13 +420,12 @@ static void msm_iommu_remove_device(stru
unsigned long flags;
spin_lock_irqsave(&msm_iommu_lock, flags);
-
iommu = find_iommu_for_dev(dev);
+ spin_unlock_irqrestore(&msm_iommu_lock, flags);
+
if (iommu)
iommu_device_unlink(&iommu->iommu, dev);
- spin_unlock_irqrestore(&msm_iommu_lock, flags);
-
iommu_group_remove_device(dev);
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Akinobu Mita <[email protected]>
[ Upstream commit 22216ec41e919682c15345e95928f266e8ba6f9e ]
The banding filter ON/OFF is controlled via bit 5 of COM8 register. It
is attempted to be enabled in ov772x_set_params() by the following line.
ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, 1);
But this unexpectedly results disabling the banding filter, because the
mask and set bits are exclusive.
On the other hand, ov772x_s_ctrl() correctly sets the bit by:
ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, BNDF_ON_OFF);
The same fix was already applied to non-soc_camera version of ov772x
driver in the commit commit a024ee14cd36 ("media: ov772x: correct setting
of banding filter")
Cc: Jacopo Mondi <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Hans Verkuil <[email protected]>
Signed-off-by: Akinobu Mita <[email protected]>
Signed-off-by: Sakari Ailus <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/media/i2c/soc_camera/ov772x.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/media/i2c/soc_camera/ov772x.c
+++ b/drivers/media/i2c/soc_camera/ov772x.c
@@ -834,7 +834,7 @@ static int ov772x_set_params(struct ov77
* set COM8
*/
if (priv->band_filter) {
- ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, 1);
+ ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, BNDF_ON_OFF);
if (!ret)
ret = ov772x_mask_set(client, BDBASE,
0xff, 256 - priv->band_filter);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Thomas Gleixner <[email protected]>
[ Upstream commit 78c9c4dfbf8c04883941445a195276bb4bb92c76 ]
The posix timer overrun handling is broken because the forwarding functions
can return a huge number of overruns which does not fit in an int. As a
consequence timer_getoverrun(2) and siginfo::si_overrun can turn into
random number generators.
The k_clock::timer_forward() callbacks return a 64 bit value now. Make
k_itimer::ti_overrun[_last] 64bit as well, so the kernel internal
accounting is correct. 3Remove the temporary (int) casts.
Add a helper function which clamps the overrun value returned to user space
via timer_getoverrun(2) or siginfo::si_overrun limited to a positive value
between 0 and INT_MAX. INT_MAX is an indicator for user space that the
overrun value has been clamped.
Reported-by: Team OWL337 <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Acked-by: John Stultz <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Michael Kerrisk <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
include/linux/posix-timers.h | 4 ++--
kernel/time/posix-cpu-timers.c | 2 +-
kernel/time/posix-timers.c | 31 ++++++++++++++++++++-----------
3 files changed, 23 insertions(+), 14 deletions(-)
--- a/include/linux/posix-timers.h
+++ b/include/linux/posix-timers.h
@@ -82,8 +82,8 @@ struct k_itimer {
clockid_t it_clock;
timer_t it_id;
int it_active;
- int it_overrun;
- int it_overrun_last;
+ s64 it_overrun;
+ s64 it_overrun_last;
int it_requeue_pending;
int it_sigev_notify;
ktime_t it_interval;
--- a/kernel/time/posix-cpu-timers.c
+++ b/kernel/time/posix-cpu-timers.c
@@ -84,7 +84,7 @@ static void bump_cpu_timer(struct k_itim
continue;
timer->it.cpu.expires += incr;
- timer->it_overrun += 1 << i;
+ timer->it_overrun += 1LL << i;
delta -= incr;
}
}
--- a/kernel/time/posix-timers.c
+++ b/kernel/time/posix-timers.c
@@ -283,6 +283,17 @@ static __init int init_posix_timers(void
}
__initcall(init_posix_timers);
+/*
+ * The siginfo si_overrun field and the return value of timer_getoverrun(2)
+ * are of type int. Clamp the overrun value to INT_MAX
+ */
+static inline int timer_overrun_to_int(struct k_itimer *timr, int baseval)
+{
+ s64 sum = timr->it_overrun_last + (s64)baseval;
+
+ return sum > (s64)INT_MAX ? INT_MAX : (int)sum;
+}
+
static void common_hrtimer_rearm(struct k_itimer *timr)
{
struct hrtimer *timer = &timr->it.real.timer;
@@ -290,9 +301,8 @@ static void common_hrtimer_rearm(struct
if (!timr->it_interval)
return;
- timr->it_overrun += (unsigned int) hrtimer_forward(timer,
- timer->base->get_time(),
- timr->it_interval);
+ timr->it_overrun += hrtimer_forward(timer, timer->base->get_time(),
+ timr->it_interval);
hrtimer_restart(timer);
}
@@ -321,10 +331,10 @@ void posixtimer_rearm(struct siginfo *in
timr->it_active = 1;
timr->it_overrun_last = timr->it_overrun;
- timr->it_overrun = -1;
+ timr->it_overrun = -1LL;
++timr->it_requeue_pending;
- info->si_overrun += timr->it_overrun_last;
+ info->si_overrun = timer_overrun_to_int(timr, info->si_overrun);
}
unlock_timer(timr, flags);
@@ -418,9 +428,8 @@ static enum hrtimer_restart posix_timer_
now = ktime_add(now, kj);
}
#endif
- timr->it_overrun += (unsigned int)
- hrtimer_forward(timer, now,
- timr->it_interval);
+ timr->it_overrun += hrtimer_forward(timer, now,
+ timr->it_interval);
ret = HRTIMER_RESTART;
++timr->it_requeue_pending;
timr->it_active = 1;
@@ -524,7 +533,7 @@ static int do_timer_create(clockid_t whi
new_timer->it_id = (timer_t) new_timer_id;
new_timer->it_clock = which_clock;
new_timer->kclock = kc;
- new_timer->it_overrun = -1;
+ new_timer->it_overrun = -1LL;
if (event) {
rcu_read_lock();
@@ -702,7 +711,7 @@ void common_timer_get(struct k_itimer *t
* expiry time forward by intervals, so expiry is > now.
*/
if (iv && (timr->it_requeue_pending & REQUEUE_PENDING || sig_none))
- timr->it_overrun += (int)kc->timer_forward(timr, now);
+ timr->it_overrun += kc->timer_forward(timr, now);
remaining = kc->timer_remaining(timr, now);
/* Return 0 only, when the timer is expired and not pending */
@@ -789,7 +798,7 @@ SYSCALL_DEFINE1(timer_getoverrun, timer_
if (!timr)
return -EINVAL;
- overrun = timr->it_overrun_last;
+ overrun = timer_overrun_to_int(timr, 0);
unlock_timer(timr, flags);
return overrun;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Nicholas Mc Guire <[email protected]>
[ Upstream commit 222bce5eb88d1af656419db04bcd84b2419fb900 ]
Both calls to of_find_node_by_name() and of_get_next_child() return a
node pointer with refcount incremented thus it must be explicidly
decremented here after the last usage. As we are assured to have a
refcounted np either from the initial
of_find_node_by_name(NULL, name); or from the of_get_next_child(gpio, np)
in the while loop if we reached the error code path below, an
x of_node_put(np) is needed.
Signed-off-by: Nicholas Mc Guire <[email protected]>
Fixes: commit f3d9478b2ce4 ("[ALSA] snd-aoa: add snd-aoa")
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/aoa/core/gpio-feature.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
--- a/sound/aoa/core/gpio-feature.c
+++ b/sound/aoa/core/gpio-feature.c
@@ -88,8 +88,10 @@ static struct device_node *get_gpio(char
}
reg = of_get_property(np, "reg", NULL);
- if (!reg)
+ if (!reg) {
+ of_node_put(np);
return NULL;
+ }
*gpioptr = *reg;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Thomas Gleixner <[email protected]>
[ Upstream commit 6fec64e1c92d5c715c6d0f50786daa7708266bde ]
The posix timer ti_overrun handling is broken because the forwarding
functions can return a huge number of overruns which does not fit in an
int. As a consequence timer_getoverrun(2) and siginfo::si_overrun can turn
into random number generators.
As a first step to address that let the timer_forward() callbacks return
the full 64 bit value.
Cast it to (int) temporarily until k_itimer::ti_overrun is converted to
64bit and the conversion to user space visible values is sanitized.
Reported-by: Team OWL337 <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Acked-by: John Stultz <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Michael Kerrisk <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
kernel/time/alarmtimer.c | 4 ++--
kernel/time/posix-timers.c | 6 +++---
kernel/time/posix-timers.h | 2 +-
3 files changed, 6 insertions(+), 6 deletions(-)
--- a/kernel/time/alarmtimer.c
+++ b/kernel/time/alarmtimer.c
@@ -581,11 +581,11 @@ static void alarm_timer_rearm(struct k_i
* @timr: Pointer to the posixtimer data struct
* @now: Current time to forward the timer against
*/
-static int alarm_timer_forward(struct k_itimer *timr, ktime_t now)
+static s64 alarm_timer_forward(struct k_itimer *timr, ktime_t now)
{
struct alarm *alarm = &timr->it.alarm.alarmtimer;
- return (int) alarm_forward(alarm, timr->it_interval, now);
+ return alarm_forward(alarm, timr->it_interval, now);
}
/**
--- a/kernel/time/posix-timers.c
+++ b/kernel/time/posix-timers.c
@@ -645,11 +645,11 @@ static ktime_t common_hrtimer_remaining(
return __hrtimer_expires_remaining_adjusted(timer, now);
}
-static int common_hrtimer_forward(struct k_itimer *timr, ktime_t now)
+static s64 common_hrtimer_forward(struct k_itimer *timr, ktime_t now)
{
struct hrtimer *timer = &timr->it.real.timer;
- return (int)hrtimer_forward(timer, now, timr->it_interval);
+ return hrtimer_forward(timer, now, timr->it_interval);
}
/*
@@ -702,7 +702,7 @@ void common_timer_get(struct k_itimer *t
* expiry time forward by intervals, so expiry is > now.
*/
if (iv && (timr->it_requeue_pending & REQUEUE_PENDING || sig_none))
- timr->it_overrun += kc->timer_forward(timr, now);
+ timr->it_overrun += (int)kc->timer_forward(timr, now);
remaining = kc->timer_remaining(timr, now);
/* Return 0 only, when the timer is expired and not pending */
--- a/kernel/time/posix-timers.h
+++ b/kernel/time/posix-timers.h
@@ -19,7 +19,7 @@ struct k_clock {
void (*timer_get)(struct k_itimer *timr,
struct itimerspec64 *cur_setting);
void (*timer_rearm)(struct k_itimer *timr);
- int (*timer_forward)(struct k_itimer *timr, ktime_t now);
+ s64 (*timer_forward)(struct k_itimer *timr, ktime_t now);
ktime_t (*timer_remaining)(struct k_itimer *timr, ktime_t now);
int (*timer_try_to_cancel)(struct k_itimer *timr);
void (*timer_arm)(struct k_itimer *timr, ktime_t expires,
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Akinobu Mita <[email protected]>
[ Upstream commit 9048f1f18a70a01eaa3c8e7166fdb2538929d780 ]
Currently the address field in iio_chan_spec is filled with an accel
data register address for the corresponding axis.
In preparation for adding calibration offset support, this sets the
address field to the index of accel data registers instead of the actual
register address.
This change makes it easier to access both accel registers and
calibration offset registers with fewer lines of code as these are
located in X-axis, Y-axis, Z-axis order.
Cc: Eva Rachel Retuya <[email protected]>
Cc: Andy Shevchenko <[email protected]>
Cc: Jonathan Cameron <[email protected]>
Signed-off-by: Akinobu Mita <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/iio/accel/adxl345_core.c | 21 ++++++++++++---------
1 file changed, 12 insertions(+), 9 deletions(-)
--- a/drivers/iio/accel/adxl345_core.c
+++ b/drivers/iio/accel/adxl345_core.c
@@ -21,6 +21,8 @@
#define ADXL345_REG_DATAX0 0x32
#define ADXL345_REG_DATAY0 0x34
#define ADXL345_REG_DATAZ0 0x36
+#define ADXL345_REG_DATA_AXIS(index) \
+ (ADXL345_REG_DATAX0 + (index) * sizeof(__le16))
#define ADXL345_POWER_CTL_MEASURE BIT(3)
#define ADXL345_POWER_CTL_STANDBY 0x00
@@ -47,19 +49,19 @@ struct adxl345_data {
u8 data_range;
};
-#define ADXL345_CHANNEL(reg, axis) { \
+#define ADXL345_CHANNEL(index, axis) { \
.type = IIO_ACCEL, \
.modified = 1, \
.channel2 = IIO_MOD_##axis, \
- .address = reg, \
+ .address = index, \
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
}
static const struct iio_chan_spec adxl345_channels[] = {
- ADXL345_CHANNEL(ADXL345_REG_DATAX0, X),
- ADXL345_CHANNEL(ADXL345_REG_DATAY0, Y),
- ADXL345_CHANNEL(ADXL345_REG_DATAZ0, Z),
+ ADXL345_CHANNEL(0, X),
+ ADXL345_CHANNEL(1, Y),
+ ADXL345_CHANNEL(2, Z),
};
static int adxl345_read_raw(struct iio_dev *indio_dev,
@@ -67,7 +69,7 @@ static int adxl345_read_raw(struct iio_d
int *val, int *val2, long mask)
{
struct adxl345_data *data = iio_priv(indio_dev);
- __le16 regval;
+ __le16 accel;
int ret;
switch (mask) {
@@ -77,12 +79,13 @@ static int adxl345_read_raw(struct iio_d
* ADXL345_REG_DATA(X0/Y0/Z0) contain the least significant byte
* and ADXL345_REG_DATA(X0/Y0/Z0) + 1 the most significant byte
*/
- ret = regmap_bulk_read(data->regmap, chan->address, ®val,
- sizeof(regval));
+ ret = regmap_bulk_read(data->regmap,
+ ADXL345_REG_DATA_AXIS(chan->address),
+ &accel, sizeof(accel));
if (ret < 0)
return ret;
- *val = sign_extend32(le16_to_cpu(regval), 12);
+ *val = sign_extend32(le16_to_cpu(accel), 12);
return IIO_VAL_INT;
case IIO_CHAN_INFO_SCALE:
*val = 0;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Peter Rosin <[email protected]>
[ Upstream commit efc6362c6f8c1e74b340e2611f1b35e7d557ce7b ]
On a sama5d31 with a Full-HD dual LVDS panel (132MHz pixel clock) NAND
flash accesses have a tendency to cause display disturbances. Add a
module param to disable DMA from the NAND controller, since that fixes
the display problem for me.
Signed-off-by: Peter Rosin <[email protected]>
Reviewed-by: Boris Brezillon <[email protected]>
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/mtd/nand/atmel/nand-controller.c | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
--- a/drivers/mtd/nand/atmel/nand-controller.c
+++ b/drivers/mtd/nand/atmel/nand-controller.c
@@ -129,6 +129,11 @@
#define DEFAULT_TIMEOUT_MS 1000
#define MIN_DMA_LEN 128
+static bool atmel_nand_avoid_dma __read_mostly;
+
+MODULE_PARM_DESC(avoiddma, "Avoid using DMA");
+module_param_named(avoiddma, atmel_nand_avoid_dma, bool, 0400);
+
enum atmel_nand_rb_type {
ATMEL_NAND_NO_RB,
ATMEL_NAND_NATIVE_RB,
@@ -1975,7 +1980,7 @@ static int atmel_nand_controller_init(st
return ret;
}
- if (nc->caps->has_dma) {
+ if (nc->caps->has_dma && !atmel_nand_avoid_dma) {
dma_cap_mask_t mask;
dma_cap_zero(mask);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Vasily Gorbik <[email protected]>
[ Upstream commit 6b2ddf33baec23dace85bd647e3fc4ac070963e8 ]
arch/s390/mm/extmem.c: In function '__segment_load':
arch/s390/mm/extmem.c:436:2: warning: 'strncat' specified bound 7 equals
source length [-Wstringop-overflow=]
strncat(seg->res_name, " (DCSS)", 7);
What gcc complains about here is the misuse of strncat function, which
in this case does not limit a number of bytes taken from "src", so it is
in the end the same as strcat(seg->res_name, " (DCSS)");
Keeping in mind that a res_name is 15 bytes, strncat in this case
would overflow the buffer and write 0 into alignment byte between the
fields in the struct. To avoid that increasing res_name size to 16,
and reusing strlcat.
Reviewed-by: Heiko Carstens <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
Signed-off-by: Martin Schwidefsky <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/s390/mm/extmem.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/arch/s390/mm/extmem.c
+++ b/arch/s390/mm/extmem.c
@@ -80,7 +80,7 @@ struct qin64 {
struct dcss_segment {
struct list_head list;
char dcss_name[8];
- char res_name[15];
+ char res_name[16];
unsigned long start_addr;
unsigned long end;
atomic_t ref_count;
@@ -433,7 +433,7 @@ __segment_load (char *name, int do_nonsh
memcpy(&seg->res_name, seg->dcss_name, 8);
EBCASC(seg->res_name, 8);
seg->res_name[8] = '\0';
- strncat(seg->res_name, " (DCSS)", 7);
+ strlcat(seg->res_name, " (DCSS)", sizeof(seg->res_name));
seg->res->name = seg->res_name;
rc = seg->vm_segtype;
if (rc == SEG_TYPE_SC ||
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Thomas Gleixner <[email protected]>
[ Upstream commit 5f936e19cc0ef97dbe3a56e9498922ad5ba1edef ]
Air Icy reported:
UBSAN: Undefined behaviour in kernel/time/alarmtimer.c:811:7
signed integer overflow:
1529859276030040771 + 9223372036854775807 cannot be represented in type 'long long int'
Call Trace:
alarm_timer_nsleep+0x44c/0x510 kernel/time/alarmtimer.c:811
__do_sys_clock_nanosleep kernel/time/posix-timers.c:1235 [inline]
__se_sys_clock_nanosleep kernel/time/posix-timers.c:1213 [inline]
__x64_sys_clock_nanosleep+0x326/0x4e0 kernel/time/posix-timers.c:1213
do_syscall_64+0xb8/0x3a0 arch/x86/entry/common.c:290
alarm_timer_nsleep() uses ktime_add() to add the current time and the
relative expiry value. ktime_add() has no sanity checks so the addition
can overflow when the relative timeout is large enough.
Use ktime_add_safe() which has the necessary sanity checks in place and
limits the result to the valid range.
Fixes: 9a7adcf5c6de ("timers: Posix interface for alarm-timers")
Reported-by: Team OWL337 <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: John Stultz <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
kernel/time/alarmtimer.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
--- a/kernel/time/alarmtimer.c
+++ b/kernel/time/alarmtimer.c
@@ -808,7 +808,8 @@ static int alarm_timer_nsleep(const cloc
/* Convert (if necessary) to absolute time */
if (flags != TIMER_ABSTIME) {
ktime_t now = alarm_bases[type].gettime();
- exp = ktime_add(now, exp);
+
+ exp = ktime_add_safe(now, exp);
}
ret = alarmtimer_do_nsleep(&alarm, exp, type);
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Heiko Carstens <[email protected]>
[ Upstream commit 9f35b818a2f90fb6cb291aa0c9f835d4f0974a9a ]
Get rid of this compile warning for !PROC_FS:
CC arch/s390/kernel/sysinfo.o
arch/s390/kernel/sysinfo.c:275:12: warning: 'sysinfo_show' defined but not used [-Wunused-function]
static int sysinfo_show(struct seq_file *m, void *v)
Signed-off-by: Heiko Carstens <[email protected]>
Signed-off-by: Martin Schwidefsky <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/s390/kernel/sysinfo.c | 4 ++++
1 file changed, 4 insertions(+)
--- a/arch/s390/kernel/sysinfo.c
+++ b/arch/s390/kernel/sysinfo.c
@@ -59,6 +59,8 @@ int stsi(void *sysinfo, int fc, int sel1
}
EXPORT_SYMBOL(stsi);
+#ifdef CONFIG_PROC_FS
+
static bool convert_ext_name(unsigned char encoding, char *name, size_t len)
{
switch (encoding) {
@@ -311,6 +313,8 @@ static int __init sysinfo_create_proc(vo
}
device_initcall(sysinfo_create_proc);
+#endif /* CONFIG_PROC_FS */
+
/*
* Service levels interface.
*/
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Benjamin Tissoires <[email protected]>
[ Upstream commit 3ffa6583e24e1ad1abab836d24bfc9d2308074e5 ]
If a device gets removed right after having registered a power_supply node,
we might enter in a deadlock between the remove call (that has a lock on
the parent device) and the deferred register work.
Allow the deferred register work to exit without taking the lock when
we are in the remove state.
Stack trace on a Ubuntu 16.04:
[16072.109121] INFO: task kworker/u16:2:1180 blocked for more than 120 seconds.
[16072.109127] Not tainted 4.13.0-41-generic #46~16.04.1-Ubuntu
[16072.109129] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[16072.109132] kworker/u16:2 D 0 1180 2 0x80000000
[16072.109142] Workqueue: events_power_efficient power_supply_deferred_register_work
[16072.109144] Call Trace:
[16072.109152] __schedule+0x3d6/0x8b0
[16072.109155] schedule+0x36/0x80
[16072.109158] schedule_preempt_disabled+0xe/0x10
[16072.109161] __mutex_lock.isra.2+0x2ab/0x4e0
[16072.109166] __mutex_lock_slowpath+0x13/0x20
[16072.109168] ? __mutex_lock_slowpath+0x13/0x20
[16072.109171] mutex_lock+0x2f/0x40
[16072.109174] power_supply_deferred_register_work+0x2b/0x50
[16072.109179] process_one_work+0x15b/0x410
[16072.109182] worker_thread+0x4b/0x460
[16072.109186] kthread+0x10c/0x140
[16072.109189] ? process_one_work+0x410/0x410
[16072.109191] ? kthread_create_on_node+0x70/0x70
[16072.109194] ret_from_fork+0x35/0x40
[16072.109199] INFO: task test:2257 blocked for more than 120 seconds.
[16072.109202] Not tainted 4.13.0-41-generic #46~16.04.1-Ubuntu
[16072.109204] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[16072.109206] test D 0 2257 2256 0x00000004
[16072.109208] Call Trace:
[16072.109211] __schedule+0x3d6/0x8b0
[16072.109215] schedule+0x36/0x80
[16072.109218] schedule_timeout+0x1f3/0x360
[16072.109221] ? check_preempt_curr+0x5a/0xa0
[16072.109224] ? ttwu_do_wakeup+0x1e/0x150
[16072.109227] wait_for_completion+0xb4/0x140
[16072.109230] ? wait_for_completion+0xb4/0x140
[16072.109233] ? wake_up_q+0x70/0x70
[16072.109236] flush_work+0x129/0x1e0
[16072.109240] ? worker_detach_from_pool+0xb0/0xb0
[16072.109243] __cancel_work_timer+0x10f/0x190
[16072.109247] ? device_del+0x264/0x310
[16072.109250] ? __wake_up+0x44/0x50
[16072.109253] cancel_delayed_work_sync+0x13/0x20
[16072.109257] power_supply_unregister+0x37/0xb0
[16072.109260] devm_power_supply_release+0x11/0x20
[16072.109263] release_nodes+0x110/0x200
[16072.109266] devres_release_group+0x7c/0xb0
[16072.109274] wacom_remove+0xc2/0x110 [wacom]
[16072.109279] hid_device_remove+0x6e/0xd0 [hid]
[16072.109284] device_release_driver_internal+0x158/0x210
[16072.109288] device_release_driver+0x12/0x20
[16072.109291] bus_remove_device+0xec/0x160
[16072.109293] device_del+0x1de/0x310
[16072.109298] hid_destroy_device+0x27/0x60 [hid]
[16072.109303] usbhid_disconnect+0x51/0x70 [usbhid]
[16072.109308] usb_unbind_interface+0x77/0x270
[16072.109311] device_release_driver_internal+0x158/0x210
[16072.109315] device_release_driver+0x12/0x20
[16072.109318] usb_driver_release_interface+0x77/0x80
[16072.109321] proc_ioctl+0x20f/0x250
[16072.109325] usbdev_do_ioctl+0x57f/0x1140
[16072.109327] ? __wake_up+0x44/0x50
[16072.109331] usbdev_ioctl+0xe/0x20
[16072.109336] do_vfs_ioctl+0xa4/0x600
[16072.109339] ? vfs_write+0x15a/0x1b0
[16072.109343] SyS_ioctl+0x79/0x90
[16072.109347] entry_SYSCALL_64_fastpath+0x24/0xab
[16072.109349] RIP: 0033:0x7f20da807f47
[16072.109351] RSP: 002b:00007ffc422ae398 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[16072.109353] RAX: ffffffffffffffda RBX: 00000000010b8560 RCX: 00007f20da807f47
[16072.109355] RDX: 00007ffc422ae3a0 RSI: 00000000c0105512 RDI: 0000000000000009
[16072.109356] RBP: 0000000000000000 R08: 00007ffc422ae3e0 R09: 0000000000000010
[16072.109357] R10: 00000000000000a6 R11: 0000000000000246 R12: 0000000000000000
[16072.109359] R13: 00000000010b8560 R14: 00007ffc422ae2e0 R15: 0000000000000000
Reported-and-tested-by: Richard Hughes <[email protected]>
Tested-by: Aaron Skomra <[email protected]>
Signed-off-by: Benjamin Tissoires <[email protected]>
Fixes: 7f1a57fdd6cb ("power_supply: Fix possible NULL pointer dereference on early uevent")
Signed-off-by: Sebastian Reichel <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/power/supply/power_supply_core.c | 11 +++++++++--
include/linux/power_supply.h | 1 +
2 files changed, 10 insertions(+), 2 deletions(-)
--- a/drivers/power/supply/power_supply_core.c
+++ b/drivers/power/supply/power_supply_core.c
@@ -14,6 +14,7 @@
#include <linux/types.h>
#include <linux/init.h>
#include <linux/slab.h>
+#include <linux/delay.h>
#include <linux/device.h>
#include <linux/notifier.h>
#include <linux/err.h>
@@ -139,8 +140,13 @@ static void power_supply_deferred_regist
struct power_supply *psy = container_of(work, struct power_supply,
deferred_register_work.work);
- if (psy->dev.parent)
- mutex_lock(&psy->dev.parent->mutex);
+ if (psy->dev.parent) {
+ while (!mutex_trylock(&psy->dev.parent->mutex)) {
+ if (psy->removing)
+ return;
+ msleep(10);
+ }
+ }
power_supply_changed(psy);
@@ -1071,6 +1077,7 @@ EXPORT_SYMBOL_GPL(devm_power_supply_regi
void power_supply_unregister(struct power_supply *psy)
{
WARN_ON(atomic_dec_return(&psy->use_cnt));
+ psy->removing = true;
cancel_work_sync(&psy->changed_work);
cancel_delayed_work_sync(&psy->deferred_register_work);
sysfs_remove_link(&psy->dev.kobj, "powers");
--- a/include/linux/power_supply.h
+++ b/include/linux/power_supply.h
@@ -251,6 +251,7 @@ struct power_supply {
spinlock_t changed_lock;
bool changed;
bool initialized;
+ bool removing;
atomic_t use_cnt;
#ifdef CONFIG_THERMAL
struct thermal_zone_device *tzd;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Michael Scott <[email protected]>
[ Upstream commit 03bc05e1a4972f73b4eb8907aa373369e825c252 ]
After decompression of 6lowpan socket data, an IPv6 header is inserted
before the existing socket payload. After this, we reset the
network_header value of the skb to account for the difference in payload
size from prior to decompression + the addition of the IPv6 header.
However, we fail to reset the mac_header value.
Leaving the mac_header value untouched here, can cause a calculation
error in net/packet/af_packet.c packet_rcv() function when an
AF_PACKET socket is opened in SOCK_RAW mode for use on a 6lowpan
interface.
On line 2088, the data pointer is moved backward by the value returned
from skb_mac_header(). If skb->data is adjusted so that it is before
the skb->head pointer (which can happen when an old value of mac_header
is left in place) the kernel generates a panic in net/core/skbuff.c
line 1717.
This panic can be generated by BLE 6lowpan interfaces (such as bt0) and
802.15.4 interfaces (such as lowpan0) as they both use the same 6lowpan
sources for compression and decompression.
Signed-off-by: Michael Scott <[email protected]>
Acked-by: Alexander Aring <[email protected]>
Acked-by: Jukka Rissanen <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/6lowpan/iphc.c | 1 +
1 file changed, 1 insertion(+)
--- a/net/6lowpan/iphc.c
+++ b/net/6lowpan/iphc.c
@@ -770,6 +770,7 @@ int lowpan_header_decompress(struct sk_b
hdr.hop_limit, &hdr.daddr);
skb_push(skb, sizeof(hdr));
+ skb_reset_mac_header(skb);
skb_reset_network_header(skb);
skb_copy_to_linear_data(skb, &hdr, sizeof(hdr));
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Alagu Sankar <[email protected]>
[ Upstream commit 8530b4e7b22bc3bd8240579f3844c73947cd5f71 ]
Without this, packets larger than 1500 will silently be dropped.
Easily reproduced by sending a ping packet with a size larger
than 1500.
Co-Developed-by: Niklas Cassel <[email protected]>
Signed-off-by: Alagu Sankar <[email protected]>
Signed-off-by: Niklas Cassel <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/wireless/ath/ath10k/sdio.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/net/wireless/ath/ath10k/sdio.c
+++ b/drivers/net/wireless/ath/ath10k/sdio.c
@@ -396,6 +396,7 @@ static int ath10k_sdio_mbox_rx_process_p
int ret;
payload_len = le16_to_cpu(htc_hdr->len);
+ skb->len = payload_len + sizeof(struct ath10k_htc_hdr);
if (trailer_present) {
trailer = skb->data + sizeof(*htc_hdr) +
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Alexey Kardashevskiy <[email protected]>
[ Upstream commit d3d4ffaae439981e1e441ebb125aa3588627c5d8 ]
We use PHB in mode1 which uses bit 59 to select a correct DMA window.
However there is mode2 which uses bits 59:55 and allows up to 32 DMA
windows per a PE.
Even though documentation does not clearly specify that, it seems that
the actual hardware does not support bits 59:55 even in mode1, in other
words we can create a window as big as 1<<58 but DMA simply won't work.
This reduces the upper limit from 59 to 55 bits to let the userspace know
about the hardware limits.
Fixes: 7aafac11e3 "powerpc/powernv/ioda2: Gracefully fail if too many TCE levels requested"
Signed-off-by: Alexey Kardashevskiy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/powerpc/platforms/powernv/pci-ioda.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/arch/powerpc/platforms/powernv/pci-ioda.c
+++ b/arch/powerpc/platforms/powernv/pci-ioda.c
@@ -2787,7 +2787,7 @@ static long pnv_pci_ioda2_table_alloc_pa
level_shift = entries_shift + 3;
level_shift = max_t(unsigned, level_shift, PAGE_SHIFT);
- if ((level_shift - 3) * levels + page_shift >= 60)
+ if ((level_shift - 3) * levels + page_shift >= 55)
return -EINVAL;
/* Allocate TCE table */
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Julia Lawall <[email protected]>
[ Upstream commit d3ac5598c5010a8999978ebbcca3b1c6188ca36b ]
Comparing an int to a size, which is unsigned, causes the int to become
unsigned, giving the wrong result. usb_get_descriptor can return a
negative error code.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
int x;
expression e,e1;
identifier f;
@@
*x = f(...);
... when != x = e1
when != if (x < 0 || ...) { ... return ...; }
*x < sizeof(e)
// </smpl>
Signed-off-by: Julia Lawall <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/wusbcore/security.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/usb/wusbcore/security.c
+++ b/drivers/usb/wusbcore/security.c
@@ -230,7 +230,7 @@ int wusb_dev_sec_add(struct wusbhc *wusb
result = usb_get_descriptor(usb_dev, USB_DT_SECURITY,
0, secd, sizeof(*secd));
- if (result < sizeof(*secd)) {
+ if (result < (int)sizeof(*secd)) {
dev_err(dev, "Can't read security descriptor or "
"not enough data: %d\n", result);
goto out;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Breno Leitao <[email protected]>
[ Upstream commit 1262dc09dc9ae7bf4ad00b6a2c5ed6a6936bcd10 ]
Currently an open firmware property is copied into partition_name variable
without keeping a room for \0.
Later one, this variable (partition_name), which is 97 bytes long, is
strncpyed into ibmvcsci_host_data->madapter_info->partition_name, which is
96 bytes long, possibly truncating it 'again' and removing the \0.
This patch simply decreases the partition name to 96 and just copy using
strlcpy() which guarantees that the string is \0 terminated. I think there
is no issue if this there is a truncation in this very first copy, i.e,
when the open firmware property is read and copied into the driver for the
very first time;
This issue also causes the following warning on GCC 8:
drivers/scsi/ibmvscsi/ibmvscsi.c:281:2: warning: strncpy output may be truncated copying 96 bytes from a string of length 96 [-Wstringop-truncation]
...
inlined from ibmvscsi_probe at drivers/scsi/ibmvscsi/ibmvscsi.c:2221:7:
drivers/scsi/ibmvscsi/ibmvscsi.c:265:3: warning: strncpy specified bound 97 equals destination size [-Wstringop-truncation]
CC: Bart Van Assche <[email protected]>
CC: Tyrel Datwyler <[email protected]>
Signed-off-by: Breno Leitao <[email protected]>
Acked-by: Tyrel Datwyler <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/scsi/ibmvscsi/ibmvscsi.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/drivers/scsi/ibmvscsi/ibmvscsi.c
+++ b/drivers/scsi/ibmvscsi/ibmvscsi.c
@@ -93,7 +93,7 @@ static int max_requests = IBMVSCSI_MAX_R
static int max_events = IBMVSCSI_MAX_REQUESTS_DEFAULT + 2;
static int fast_fail = 1;
static int client_reserve = 1;
-static char partition_name[97] = "UNKNOWN";
+static char partition_name[96] = "UNKNOWN";
static unsigned int partition_number = -1;
static LIST_HEAD(ibmvscsi_head);
@@ -262,7 +262,7 @@ static void gather_partition_info(void)
ppartition_name = of_get_property(of_root, "ibm,partition-name", NULL);
if (ppartition_name)
- strncpy(partition_name, ppartition_name,
+ strlcpy(partition_name, ppartition_name,
sizeof(partition_name));
p_number_ptr = of_get_property(of_root, "ibm,partition-no", NULL);
if (p_number_ptr)
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Bart Van Assche <[email protected]>
[ Upstream commit 36d4cb460bcbe2a1323732a6e4bb9dd783284368 ]
The approach for adding a device to the devices_idr data structure and for
removing it is as follows:
* &dev->dev_group.cg_item is initialized before a device is added to
devices_idr.
* If the reference count of a device drops to zero then
target_free_device() removes the device from devices_idr.
* All devices_idr manipulations are protected by device_mutex.
This means that increasing the reference count of a device is sufficient to
prevent removal from devices_idr and also that it is safe access
dev_group.cg_item for any device that is referenced by devices_idr. Use
this to modify target_find_device() and target_for_each_device() such that
these functions no longer introduce a dependency between device_mutex and
the configfs root inode mutex.
Note: it is safe to pass a NULL pointer to config_item_put() and also to
config_item_get_unless_zero().
This patch prevents that lockdep reports the following complaint:
======================================================
WARNING: possible circular locking dependency detected
4.12.0-rc1-dbg+ #1 Not tainted
------------------------------------------------------
rmdir/12053 is trying to acquire lock:
(device_mutex#2){+.+.+.}, at: [<ffffffffa010afce>]
target_free_device+0xae/0xf0 [target_core_mod]
but task is already holding lock:
(&sb->s_type->i_mutex_key#14){++++++}, at: [<ffffffff811c5c30>]
vfs_rmdir+0x50/0x140
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&sb->s_type->i_mutex_key#14){++++++}:
lock_acquire+0x59/0x80
down_write+0x36/0x70
configfs_depend_item+0x3a/0xb0 [configfs]
target_depend_item+0x13/0x20 [target_core_mod]
target_xcopy_locate_se_dev_e4_iter+0x87/0x100 [target_core_mod]
target_devices_idr_iter+0x16/0x20 [target_core_mod]
idr_for_each+0x39/0xc0
target_for_each_device+0x36/0x50 [target_core_mod]
target_xcopy_locate_se_dev_e4+0x28/0x80 [target_core_mod]
target_xcopy_do_work+0x2e9/0xdd0 [target_core_mod]
process_one_work+0x1ca/0x3f0
worker_thread+0x49/0x3b0
kthread+0x109/0x140
ret_from_fork+0x31/0x40
-> #0 (device_mutex#2){+.+.+.}:
__lock_acquire+0x101f/0x11d0
lock_acquire+0x59/0x80
__mutex_lock+0x7e/0x950
mutex_lock_nested+0x16/0x20
target_free_device+0xae/0xf0 [target_core_mod]
target_core_dev_release+0x10/0x20 [target_core_mod]
config_item_put+0x6e/0xb0 [configfs]
configfs_rmdir+0x1a6/0x300 [configfs]
vfs_rmdir+0xb7/0x140
do_rmdir+0x1f4/0x200
SyS_rmdir+0x11/0x20
entry_SYSCALL_64_fastpath+0x23/0xc2
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&sb->s_type->i_mutex_key#14);
lock(device_mutex#2);
lock(&sb->s_type->i_mutex_key#14);
lock(device_mutex#2);
*** DEADLOCK ***
3 locks held by rmdir/12053:
#0: (sb_writers#10){.+.+.+}, at: [<ffffffff811e223f>]
mnt_want_write+0x1f/0x50
#1: (&sb->s_type->i_mutex_key#14/1){+.+.+.}, at: [<ffffffff811cb97e>]
do_rmdir+0x15e/0x200
#2: (&sb->s_type->i_mutex_key#14){++++++}, at: [<ffffffff811c5c30>]
vfs_rmdir+0x50/0x140
stack backtrace:
CPU: 3 PID: 12053 Comm: rmdir Not tainted 4.12.0-rc1-dbg+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.0.0-prebuilt.qemu-project.org 04/01/2014
Call Trace:
dump_stack+0x86/0xcf
print_circular_bug+0x1c7/0x220
__lock_acquire+0x101f/0x11d0
lock_acquire+0x59/0x80
__mutex_lock+0x7e/0x950
mutex_lock_nested+0x16/0x20
target_free_device+0xae/0xf0 [target_core_mod]
target_core_dev_release+0x10/0x20 [target_core_mod]
config_item_put+0x6e/0xb0 [configfs]
configfs_rmdir+0x1a6/0x300 [configfs]
vfs_rmdir+0xb7/0x140
do_rmdir+0x1f4/0x200
SyS_rmdir+0x11/0x20
entry_SYSCALL_64_fastpath+0x23/0xc2
Signed-off-by: Bart Van Assche <[email protected]>
[Rebased to handle conflict withe target_find_device removal]
Signed-off-by: Mike Christie <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/target/target_core_device.c | 22 +++++++++++++++++-----
1 file changed, 17 insertions(+), 5 deletions(-)
--- a/drivers/target/target_core_device.c
+++ b/drivers/target/target_core_device.c
@@ -904,14 +904,20 @@ struct se_device *target_find_device(int
EXPORT_SYMBOL(target_find_device);
struct devices_idr_iter {
+ struct config_item *prev_item;
int (*fn)(struct se_device *dev, void *data);
void *data;
};
static int target_devices_idr_iter(int id, void *p, void *data)
+ __must_hold(&device_mutex)
{
struct devices_idr_iter *iter = data;
struct se_device *dev = p;
+ int ret;
+
+ config_item_put(iter->prev_item);
+ iter->prev_item = NULL;
/*
* We add the device early to the idr, so it can be used
@@ -922,7 +928,15 @@ static int target_devices_idr_iter(int i
if (!(dev->dev_flags & DF_CONFIGURED))
return 0;
- return iter->fn(dev, iter->data);
+ iter->prev_item = config_item_get_unless_zero(&dev->dev_group.cg_item);
+ if (!iter->prev_item)
+ return 0;
+ mutex_unlock(&device_mutex);
+
+ ret = iter->fn(dev, iter->data);
+
+ mutex_lock(&device_mutex);
+ return ret;
}
/**
@@ -936,15 +950,13 @@ static int target_devices_idr_iter(int i
int target_for_each_device(int (*fn)(struct se_device *dev, void *data),
void *data)
{
- struct devices_idr_iter iter;
+ struct devices_idr_iter iter = { .fn = fn, .data = data };
int ret;
- iter.fn = fn;
- iter.data = data;
-
mutex_lock(&device_mutex);
ret = idr_for_each(&devices_idr, target_devices_idr_iter, &iter);
mutex_unlock(&device_mutex);
+ config_item_put(iter.prev_item);
return ret;
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Vasily Gorbik <[email protected]>
[ Upstream commit d642d6262f4fcfa5d200ec6e218c17f0c15b3390 ]
The numa_node field of the tag_set struct has to be explicitly
initialized, otherwise it stays as 0, which is a valid numa node id and
cause memory allocation failure if node 0 is offline.
Acked-by: Sebastian Ott <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
Signed-off-by: Martin Schwidefsky <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/s390/block/scm_blk.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/s390/block/scm_blk.c
+++ b/drivers/s390/block/scm_blk.c
@@ -454,6 +454,7 @@ int scm_blk_dev_setup(struct scm_blk_dev
bdev->tag_set.nr_hw_queues = nr_requests;
bdev->tag_set.queue_depth = nr_requests_per_io * nr_requests;
bdev->tag_set.flags = BLK_MQ_F_SHOULD_MERGE;
+ bdev->tag_set.numa_node = NUMA_NO_NODE;
ret = blk_mq_alloc_tag_set(&bdev->tag_set);
if (ret)
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Vasily Gorbik <[email protected]>
[ Upstream commit b17e3abb0af404cb62ad4ef1a5962f58b06e2b78 ]
The numa_node field of the tag_set struct has to be explicitly
initialized, otherwise it stays as 0, which is a valid numa node id and
cause memory allocation failure if node 0 is offline.
Acked-by: Stefan Haberland <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
Signed-off-by: Martin Schwidefsky <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/s390/block/dasd.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/s390/block/dasd.c
+++ b/drivers/s390/block/dasd.c
@@ -3190,6 +3190,7 @@ static int dasd_alloc_queue(struct dasd_
block->tag_set.nr_hw_queues = DASD_NR_HW_QUEUES;
block->tag_set.queue_depth = DASD_MAX_LCU_DEV * DASD_REQ_PER_DEV;
block->tag_set.flags = BLK_MQ_F_SHOULD_MERGE;
+ block->tag_set.numa_node = NUMA_NO_NODE;
rc = blk_mq_alloc_tag_set(&block->tag_set);
if (rc)
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Alexey Khoroshilov <[email protected]>
[ Upstream commit 662a99e145661c2b35155cf375044deae9b79896 ]
viu_of_probe() ignores fails in i2c_get_adapter(),
tries to unlock uninitialized mutex on error path.
The patch streamlining the error handling in viu_of_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/media/platform/fsl-viu.c | 38 +++++++++++++++++++++++---------------
1 file changed, 23 insertions(+), 15 deletions(-)
--- a/drivers/media/platform/fsl-viu.c
+++ b/drivers/media/platform/fsl-viu.c
@@ -1417,7 +1417,7 @@ static int viu_of_probe(struct platform_
sizeof(struct viu_reg), DRV_NAME)) {
dev_err(&op->dev, "Error while requesting mem region\n");
ret = -EBUSY;
- goto err;
+ goto err_irq;
}
/* remap registers */
@@ -1425,7 +1425,7 @@ static int viu_of_probe(struct platform_
if (!viu_regs) {
dev_err(&op->dev, "Can't map register set\n");
ret = -ENOMEM;
- goto err;
+ goto err_irq;
}
/* Prepare our private structure */
@@ -1433,7 +1433,7 @@ static int viu_of_probe(struct platform_
if (!viu_dev) {
dev_err(&op->dev, "Can't allocate private structure\n");
ret = -ENOMEM;
- goto err;
+ goto err_irq;
}
viu_dev->vr = viu_regs;
@@ -1449,16 +1449,21 @@ static int viu_of_probe(struct platform_
ret = v4l2_device_register(viu_dev->dev, &viu_dev->v4l2_dev);
if (ret < 0) {
dev_err(&op->dev, "v4l2_device_register() failed: %d\n", ret);
- goto err;
+ goto err_irq;
}
ad = i2c_get_adapter(0);
+ if (!ad) {
+ ret = -EFAULT;
+ dev_err(&op->dev, "couldn't get i2c adapter\n");
+ goto err_v4l2;
+ }
v4l2_ctrl_handler_init(&viu_dev->hdl, 5);
if (viu_dev->hdl.error) {
ret = viu_dev->hdl.error;
dev_err(&op->dev, "couldn't register control\n");
- goto err_vdev;
+ goto err_i2c;
}
/* This control handler will inherit the control(s) from the
sub-device(s). */
@@ -1475,7 +1480,7 @@ static int viu_of_probe(struct platform_
vdev = video_device_alloc();
if (vdev == NULL) {
ret = -ENOMEM;
- goto err_vdev;
+ goto err_hdl;
}
*vdev = viu_template;
@@ -1496,7 +1501,7 @@ static int viu_of_probe(struct platform_
ret = video_register_device(viu_dev->vdev, VFL_TYPE_GRABBER, -1);
if (ret < 0) {
video_device_release(viu_dev->vdev);
- goto err_vdev;
+ goto err_unlock;
}
/* enable VIU clock */
@@ -1504,12 +1509,12 @@ static int viu_of_probe(struct platform_
if (IS_ERR(clk)) {
dev_err(&op->dev, "failed to lookup the clock!\n");
ret = PTR_ERR(clk);
- goto err_clk;
+ goto err_vdev;
}
ret = clk_prepare_enable(clk);
if (ret) {
dev_err(&op->dev, "failed to enable the clock!\n");
- goto err_clk;
+ goto err_vdev;
}
viu_dev->clk = clk;
@@ -1520,7 +1525,7 @@ static int viu_of_probe(struct platform_
if (request_irq(viu_dev->irq, viu_intr, 0, "viu", (void *)viu_dev)) {
dev_err(&op->dev, "Request VIU IRQ failed.\n");
ret = -ENODEV;
- goto err_irq;
+ goto err_clk;
}
mutex_unlock(&viu_dev->lock);
@@ -1528,16 +1533,19 @@ static int viu_of_probe(struct platform_
dev_info(&op->dev, "Freescale VIU Video Capture Board\n");
return ret;
-err_irq:
- clk_disable_unprepare(viu_dev->clk);
err_clk:
- video_unregister_device(viu_dev->vdev);
+ clk_disable_unprepare(viu_dev->clk);
err_vdev:
- v4l2_ctrl_handler_free(&viu_dev->hdl);
+ video_unregister_device(viu_dev->vdev);
+err_unlock:
mutex_unlock(&viu_dev->lock);
+err_hdl:
+ v4l2_ctrl_handler_free(&viu_dev->hdl);
+err_i2c:
i2c_put_adapter(ad);
+err_v4l2:
v4l2_device_unregister(&viu_dev->v4l2_dev);
-err:
+err_irq:
irq_dispose_mapping(viu_irq);
return ret;
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Hari Bathini <[email protected]>
[ Upstream commit 8950329c4a64c6d3ca0bc34711a1afbd9ce05657 ]
Memory reservation for crashkernel could fail if there are holes around
kdump kernel offset (128M). Fail gracefully in such cases and print an
error message.
Signed-off-by: Hari Bathini <[email protected]>
Tested-by: David Gibson <[email protected]>
Reviewed-by: Dave Young <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/powerpc/kernel/machine_kexec.c | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
--- a/arch/powerpc/kernel/machine_kexec.c
+++ b/arch/powerpc/kernel/machine_kexec.c
@@ -186,7 +186,12 @@ void __init reserve_crashkernel(void)
(unsigned long)(crashk_res.start >> 20),
(unsigned long)(memblock_phys_mem_size() >> 20));
- memblock_reserve(crashk_res.start, crash_size);
+ if (!memblock_is_region_memory(crashk_res.start, crash_size) ||
+ memblock_reserve(crashk_res.start, crash_size)) {
+ pr_err("Failed to reserve memory for crashkernel!\n");
+ crashk_res.start = crashk_res.end = 0;
+ return;
+ }
}
int overlaps_crashkernel(unsigned long start, unsigned long size)
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Sylwester Nawrocki <[email protected]>
[ Upstream commit 7c1b9a5aeed91bef98988ac0fcf38c8c1f4f9a3a ]
This patch fixes potential NULL pointer dereference as indicated
by the following static checker warning:
drivers/media/platform/exynos4-is/fimc-isp-video.c:408 isp_video_try_fmt_mplane()
error: NULL dereference inside function '__isp_video_try_fmt(isp, &f->fmt.pix_mp, (0))()'.
Fixes: 34947b8aebe3: ("[media] exynos4-is: Add the FIMC-IS ISP capture DMA driver")
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: Sylwester Nawrocki <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/media/platform/exynos4-is/fimc-isp-video.c | 11 ++++++++---
1 file changed, 8 insertions(+), 3 deletions(-)
--- a/drivers/media/platform/exynos4-is/fimc-isp-video.c
+++ b/drivers/media/platform/exynos4-is/fimc-isp-video.c
@@ -384,12 +384,17 @@ static void __isp_video_try_fmt(struct f
struct v4l2_pix_format_mplane *pixm,
const struct fimc_fmt **fmt)
{
- *fmt = fimc_isp_find_format(&pixm->pixelformat, NULL, 2);
+ const struct fimc_fmt *__fmt;
+
+ __fmt = fimc_isp_find_format(&pixm->pixelformat, NULL, 2);
+
+ if (fmt)
+ *fmt = __fmt;
pixm->colorspace = V4L2_COLORSPACE_SRGB;
pixm->field = V4L2_FIELD_NONE;
- pixm->num_planes = (*fmt)->memplanes;
- pixm->pixelformat = (*fmt)->fourcc;
+ pixm->num_planes = __fmt->memplanes;
+ pixm->pixelformat = __fmt->fourcc;
/*
* TODO: double check with the docmentation these width/height
* constraints are correct.
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Alagu Sankar <[email protected]>
[ Upstream commit 679e1f07c86221b7183dd69df7068fd42d0041f6 ]
All packets in a bundle should use the same endpoint id as the
first lookahead.
This matches how things are done is ath6kl, however,
this patch can theoretically handle several bundles
in ath10k_sdio_mbox_rx_process_packets().
Without this patch we get lots of errors about invalid endpoint id:
ath10k_sdio mmc2:0001:1: invalid endpoint in look-ahead: 224
ath10k_sdio mmc2:0001:1: failed to get pending recv messages: -12
ath10k_sdio mmc2:0001:1: failed to process pending SDIO interrupts: -12
Co-Developed-by: Niklas Cassel <[email protected]>
Signed-off-by: Alagu Sankar <[email protected]>
Signed-off-by: Niklas Cassel <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/wireless/ath/ath10k/sdio.c | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
--- a/drivers/net/wireless/ath/ath10k/sdio.c
+++ b/drivers/net/wireless/ath/ath10k/sdio.c
@@ -434,12 +434,14 @@ static int ath10k_sdio_mbox_rx_process_p
enum ath10k_htc_ep_id id;
int ret, i, *n_lookahead_local;
u32 *lookaheads_local;
+ int lookahead_idx = 0;
for (i = 0; i < ar_sdio->n_rx_pkts; i++) {
lookaheads_local = lookaheads;
n_lookahead_local = n_lookahead;
- id = ((struct ath10k_htc_hdr *)&lookaheads[i])->eid;
+ id = ((struct ath10k_htc_hdr *)
+ &lookaheads[lookahead_idx++])->eid;
if (id >= ATH10K_HTC_EP_COUNT) {
ath10k_warn(ar, "invalid endpoint in look-ahead: %d\n",
@@ -462,6 +464,7 @@ static int ath10k_sdio_mbox_rx_process_p
/* Only read lookahead's from RX trailers
* for the last packet in a bundle.
*/
+ lookahead_idx--;
lookaheads_local = NULL;
n_lookahead_local = NULL;
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Tarick Bedeir <[email protected]>
[ Upstream commit f1228867adaf8890826f2b59e4caddb1c5cc2df7 ]
rdma_ah_find_type() can reach into ib_device->port_immutable with a
potentially out-of-bounds port number, so check that the port number is
valid first.
Fixes: 44c58487d51a ("IB/core: Define 'ib' and 'roce' rdma_ah_attr types")
Signed-off-by: Tarick Bedeir <[email protected]>
Reviewed-by: Leon Romanovsky <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/infiniband/hw/mlx4/qp.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/infiniband/hw/mlx4/qp.c
+++ b/drivers/infiniband/hw/mlx4/qp.c
@@ -4014,9 +4014,9 @@ static void to_rdma_ah_attr(struct mlx4_
u8 port_num = path->sched_queue & 0x40 ? 2 : 1;
memset(ah_attr, 0, sizeof(*ah_attr));
- ah_attr->type = rdma_ah_find_type(&ibdev->ib_dev, port_num);
if (port_num == 0 || port_num > dev->caps.num_ports)
return;
+ ah_attr->type = rdma_ah_find_type(&ibdev->ib_dev, port_num);
if (ah_attr->type == RDMA_AH_ATTR_TYPE_ROCE)
rdma_ah_set_sl(ah_attr, ((path->sched_queue >> 3) & 0x7) |
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Dan Carpenter <[email protected]>
[ Upstream commit c2d7c8ff89b22ddefb1ac2986c0d48444a667689 ]
"nents" is an unsigned int, so if ib_map_mr_sg() returns a negative
error code then it's type promoted to a high unsigned int which is
treated as success.
Fixes: a060b5629ab0 ("IB/core: generic RDMA READ/WRITE API")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/infiniband/core/rw.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/infiniband/core/rw.c
+++ b/drivers/infiniband/core/rw.c
@@ -87,7 +87,7 @@ static int rdma_rw_init_one_mr(struct ib
}
ret = ib_map_mr_sg(reg->mr, sg, nents, &offset, PAGE_SIZE);
- if (ret < nents) {
+ if (ret < 0 || ret < nents) {
ib_mr_pool_put(qp, &qp->rdma_mrs, reg->mr);
return -EINVAL;
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Geert Uytterhoeven <[email protected]>
[ Upstream commit c5a9262fa8bfed0dddc7466ef10fcd292e2af61b ]
The RX FIFO timer may be armed when the port is shut down, hence the
timer function may still be called afterwards.
Fix this race condition by deleting the timer during port shutdown.
Fixes: 039403765e5da3c6 ("serial: sh-sci: SCIFA/B RX FIFO software timeout")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/tty/serial/sh-sci.c | 2 ++
1 file changed, 2 insertions(+)
--- a/drivers/tty/serial/sh-sci.c
+++ b/drivers/tty/serial/sh-sci.c
@@ -2060,6 +2060,8 @@ static void sci_shutdown(struct uart_por
}
#endif
+ if (s->rx_trigger > 1 && s->rx_fifo_timeout > 0)
+ del_timer_sync(&s->rx_fifo_timer);
sci_free_irq(s);
sci_free_dma(port);
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Hans de Goede <[email protected]>
[ Upstream commit f2a42595f0865886a2d40524b0e9d15600848670 ]
We should look at val which contains the value read from the register,
not ret which is always 0 on a successful read.
Signed-off-by: Hans de Goede <[email protected]>
Fixes: eac53b3664f59 ("power: supply: axp288_charger: Drop platform_data dependency")
Signed-off-by: Sebastian Reichel <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/power/supply/axp288_charger.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/power/supply/axp288_charger.c
+++ b/drivers/power/supply/axp288_charger.c
@@ -771,7 +771,7 @@ static int charger_init_hw_regs(struct a
}
/* Determine charge current limit */
- cc = (ret & CHRG_CCCV_CC_MASK) >> CHRG_CCCV_CC_BIT_POS;
+ cc = (val & CHRG_CCCV_CC_MASK) >> CHRG_CCCV_CC_BIT_POS;
cc = (cc * CHRG_CCCV_CC_LSB_RES) + CHRG_CCCV_CC_OFFSET;
info->cc = cc;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Colin Ian King <[email protected]>
[ Upstream commit c5fae4f4fd28189b1062fb8ef7b21fec37cb8b17 ]
Currently the check on error return from the call to rtsx_write_register
is checking the error status from the previous call. Fix this by adding
in the missing assignment of retval.
Detected by CoverityScan, CID#709877
Fixes: fa590c222fba ("staging: rts5208: add support for rts5208 and rts5288")
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/staging/rts5208/sd.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/staging/rts5208/sd.c
+++ b/drivers/staging/rts5208/sd.c
@@ -5002,7 +5002,7 @@ int sd_execute_write_data(struct scsi_cm
goto sd_execute_write_cmd_failed;
}
- rtsx_write_register(chip, SD_BYTE_CNT_L, 0xFF, 0x00);
+ retval = rtsx_write_register(chip, SD_BYTE_CNT_L, 0xFF, 0x00);
if (retval != STATUS_SUCCESS) {
rtsx_trace(chip);
goto sd_execute_write_cmd_failed;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Dan Williams <[email protected]>
[ Upstream commit 3b6c62f363a19ce82bf378187ab97c9dc01e3927 ]
Without this change the distance table calculation for emulated nodes
may use the wrong numa node and report an incorrect distance.
Signed-off-by: Dan Williams <[email protected]>
Cc: David Rientjes <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Wei Yang <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/153089328103.27680.14778434392225818887.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Ingo Molnar <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/x86/mm/numa_emulation.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/arch/x86/mm/numa_emulation.c
+++ b/arch/x86/mm/numa_emulation.c
@@ -61,7 +61,7 @@ static int __init emu_setup_memblk(struc
eb->nid = nid;
if (emu_nid_to_phys[nid] == NUMA_NO_NODE)
- emu_nid_to_phys[nid] = nid;
+ emu_nid_to_phys[nid] = pb->nid;
pb->start += size;
if (pb->start >= pb->end) {
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Peter Seiderer <[email protected]>
[ Upstream commit a38d4b71cb7a12b65317f4e3d59883a918957719 ]
- fixes gstreamer v4l2src warning:
0:00:00.716640334 349 0x164f720 WARN v4l2bufferpool gstv4l2bufferpool.c:1195:gst_v4l2_buffer_pool_dqbuf:<v4l2src0:pool:src> Driver should never set v4l2_buffer.field to ANY
- fixes v4l2-compliance test failure:
Streaming ioctls:
test read/write: OK (Not Supported)
Video Capture:
Buffer: 0 Sequence: 0 Field: Any Timestamp: 58.383658s
fail: v4l2-test-buffers.cpp(297): g_field() == V4L2_FIELD_ANY
Signed-off-by: Peter Seiderer <[email protected]>
Reviewed-by: Steve Longerbeam <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/staging/media/imx/imx-ic-prpencvf.c | 1 +
drivers/staging/media/imx/imx-media-csi.c | 1 +
2 files changed, 2 insertions(+)
--- a/drivers/staging/media/imx/imx-ic-prpencvf.c
+++ b/drivers/staging/media/imx/imx-ic-prpencvf.c
@@ -210,6 +210,7 @@ static void prp_vb2_buf_done(struct prp_
done = priv->active_vb2_buf[priv->ipu_buf_num];
if (done) {
+ done->vbuf.field = vdev->fmt.fmt.pix.field;
vb = &done->vbuf.vb2_buf;
vb->timestamp = ktime_get_ns();
vb2_buffer_done(vb, priv->nfb4eof ?
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -171,6 +171,7 @@ static void csi_vb2_buf_done(struct csi_
done = priv->active_vb2_buf[priv->ipu_buf_num];
if (done) {
+ done->vbuf.field = vdev->fmt.fmt.pix.field;
vb = &done->vbuf.vb2_buf;
vb->timestamp = ktime_get_ns();
vb2_buffer_done(vb, priv->nfb4eof ?
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Akinobu Mita <[email protected]>
[ Upstream commit 7d6cd21d82bacab2d1786fe5e989e4815b75d9a3 ]
When the buffer is enabled for ina2xx driver, a dedicated kthread is
invoked to capture mesurement data. When the buffer is disabled, the
kthread is stopped.
However if the kthread gets register access errors, it immediately exits
and when the malfunctional buffer is disabled, the stale task_struct
pointer is accessed as there is no kthread to be stopped.
A similar issue in the usbip driver is prevented by kthread_get_run and
kthread_stop_put helpers by increasing usage count of the task_struct.
This change applies the same solution.
Cc: Stefan Brüns <[email protected]>
Cc: Jonathan Cameron <[email protected]>
Signed-off-by: Akinobu Mita <[email protected]>
Fixes: c43a102e67db ("iio: ina2xx: add support for TI INA2xx Power Monitors")
Signed-off-by: Jonathan Cameron <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/iio/adc/ina2xx-adc.c | 17 +++++++++++++----
1 file changed, 13 insertions(+), 4 deletions(-)
--- a/drivers/iio/adc/ina2xx-adc.c
+++ b/drivers/iio/adc/ina2xx-adc.c
@@ -30,6 +30,7 @@
#include <linux/module.h>
#include <linux/of_device.h>
#include <linux/regmap.h>
+#include <linux/sched/task.h>
#include <linux/util_macros.h>
#include <linux/platform_data/ina2xx.h>
@@ -701,6 +702,7 @@ static int ina2xx_buffer_enable(struct i
{
struct ina2xx_chip_info *chip = iio_priv(indio_dev);
unsigned int sampling_us = SAMPLING_PERIOD(chip);
+ struct task_struct *task;
dev_dbg(&indio_dev->dev, "Enabling buffer w/ scan_mask %02x, freq = %d, avg =%u\n",
(unsigned int)(*indio_dev->active_scan_mask),
@@ -710,11 +712,17 @@ static int ina2xx_buffer_enable(struct i
dev_dbg(&indio_dev->dev, "Async readout mode: %d\n",
chip->allow_async_readout);
- chip->task = kthread_run(ina2xx_capture_thread, (void *)indio_dev,
- "%s:%d-%uus", indio_dev->name, indio_dev->id,
- sampling_us);
+ task = kthread_create(ina2xx_capture_thread, (void *)indio_dev,
+ "%s:%d-%uus", indio_dev->name, indio_dev->id,
+ sampling_us);
+ if (IS_ERR(task))
+ return PTR_ERR(task);
+
+ get_task_struct(task);
+ wake_up_process(task);
+ chip->task = task;
- return PTR_ERR_OR_ZERO(chip->task);
+ return 0;
}
static int ina2xx_buffer_disable(struct iio_dev *indio_dev)
@@ -723,6 +731,7 @@ static int ina2xx_buffer_disable(struct
if (chip->task) {
kthread_stop(chip->task);
+ put_task_struct(chip->task);
chip->task = NULL;
}
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Matt Ranostay <[email protected]>
[ Upstream commit ce054546cc2c26891cefa2f284d90d93b52205de ]
ADC channel 0 photodiode detects both infrared + visible light,
but ADC channel 1 just detects infrared. However, the latter is a bit
more sensitive in that range so complete darkness or low light causes
a error condition in which the chan0 - chan1 is negative that
results in a -EAGAIN.
This patch changes the resulting lux1_input sysfs attribute message from
"Resource temporarily unavailable" to a user-grokable lux value of 0.
Cc: Arnd Bergmann <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Matt Ranostay <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/misc/tsl2550.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/misc/tsl2550.c
+++ b/drivers/misc/tsl2550.c
@@ -177,7 +177,7 @@ static int tsl2550_calculate_lux(u8 ch0,
} else
lux = 0;
else
- return -EAGAIN;
+ return 0;
/* LUX range check */
return lux > TSL2550_MAX_LUX ? TSL2550_MAX_LUX : lux;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Stafford Horne <[email protected]>
[ Upstream commit cefd769fd0192c84d638f66da202459ed8ad63ba ]
As of GCC 9.0.0 the build is reporting warnings like:
crypto/ablkcipher.c: In function ‘crypto_ablkcipher_report’:
crypto/ablkcipher.c:374:2: warning: ‘strncpy’ specified bound 64 equals destination size [-Wstringop-truncation]
strncpy(rblkcipher.geniv, alg->cra_ablkcipher.geniv ?: "<default>",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(rblkcipher.geniv));
~~~~~~~~~~~~~~~~~~~~~~~~~
This means the strnycpy might create a non null terminated string. Fix this by
explicitly performing '\0' termination.
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Arnd Bergmann <[email protected]>
Cc: Max Filippov <[email protected]>
Cc: Eric Biggers <[email protected]>
Cc: Nick Desaulniers <[email protected]>
Signed-off-by: Stafford Horne <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
crypto/ablkcipher.c | 2 ++
crypto/blkcipher.c | 1 +
2 files changed, 3 insertions(+)
--- a/crypto/ablkcipher.c
+++ b/crypto/ablkcipher.c
@@ -368,6 +368,7 @@ static int crypto_ablkcipher_report(stru
strncpy(rblkcipher.type, "ablkcipher", sizeof(rblkcipher.type));
strncpy(rblkcipher.geniv, alg->cra_ablkcipher.geniv ?: "<default>",
sizeof(rblkcipher.geniv));
+ rblkcipher.geniv[sizeof(rblkcipher.geniv) - 1] = '\0';
rblkcipher.blocksize = alg->cra_blocksize;
rblkcipher.min_keysize = alg->cra_ablkcipher.min_keysize;
@@ -442,6 +443,7 @@ static int crypto_givcipher_report(struc
strncpy(rblkcipher.type, "givcipher", sizeof(rblkcipher.type));
strncpy(rblkcipher.geniv, alg->cra_ablkcipher.geniv ?: "<built-in>",
sizeof(rblkcipher.geniv));
+ rblkcipher.geniv[sizeof(rblkcipher.geniv) - 1] = '\0';
rblkcipher.blocksize = alg->cra_blocksize;
rblkcipher.min_keysize = alg->cra_ablkcipher.min_keysize;
--- a/crypto/blkcipher.c
+++ b/crypto/blkcipher.c
@@ -511,6 +511,7 @@ static int crypto_blkcipher_report(struc
strncpy(rblkcipher.type, "blkcipher", sizeof(rblkcipher.type));
strncpy(rblkcipher.geniv, alg->cra_blkcipher.geniv ?: "<default>",
sizeof(rblkcipher.geniv));
+ rblkcipher.geniv[sizeof(rblkcipher.geniv) - 1] = '\0';
rblkcipher.blocksize = alg->cra_blocksize;
rblkcipher.min_keysize = alg->cra_blkcipher.min_keysize;
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Anton Vasilyev <[email protected]>
[ Upstream commit 11b71782c1d10d9bccc31825cf84291cd7588a1e ]
hwarc_probe() allocates memory for hwarc, but does not free it
if uwb_rc_add() or hwarc_get_version() fail.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/uwb/hwa-rc.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/uwb/hwa-rc.c
+++ b/drivers/uwb/hwa-rc.c
@@ -873,6 +873,7 @@ error_get_version:
error_rc_add:
usb_put_intf(iface);
usb_put_dev(hwarc->usb_dev);
+ kfree(hwarc);
error_alloc:
uwb_rc_put(uwb_rc);
error_rc_alloc:
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Jian-Hong Pan <[email protected]>
[ Upstream commit 45ae68b8cfc25bdbffc11248001c47ab1b76ff6e ]
Without this patch we cannot turn on the Bluethooth adapter on HP
14-bs007la.
T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=b009 Rev= 2.00
S: Manufacturer=Realtek
S: Product=802.11n WLAN Adapter
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Jian-Hong Pan <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/bluetooth/btusb.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -375,6 +375,7 @@ static const struct usb_device_id blackl
{ USB_DEVICE(0x7392, 0xa611), .driver_info = BTUSB_REALTEK },
/* Additional Realtek 8723DE Bluetooth devices */
+ { USB_DEVICE(0x0bda, 0xb009), .driver_info = BTUSB_REALTEK },
{ USB_DEVICE(0x2ff8, 0xb011), .driver_info = BTUSB_REALTEK },
/* Additional Realtek 8821AE Bluetooth devices */
4.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Sudeep Holla <[email protected]>
[ Upstream commit 09bebb1adb21ecd04adf7ccb3b06f73e3a851e93 ]
Vexpress platforms provide two different restart handlers: SYS_REBOOT
that restart the entire system, while DB_RESET only restarts the
daughter board containing the CPU. DB_RESET is overridden by SYS_REBOOT
if it exists.
notifier_chain_register used in register_restart_handler by design
relies on notifiers to be registered once only, however vexpress restart
notifier can get registered twice. When this happen it corrupts list
of notifiers, as result some notifiers can be not called on proper
event, traverse on list can be cycled forever, and second unregister
can access already freed memory.
So far, since this was the only restart handler in the system, no issue
was observed even if the same notifier was registered twice. However
commit 6c5c0d48b686 ("watchdog: sp805: add restart handler") added
support for SP805 restart handlers and since the system under test
contains two vexpress restart and two SP805 watchdog instances, it was
observed that during the boot traversing the restart handler list looped
forever as there's a cycle in that list resulting in boot hang.
This patch fixes the issues by ensuring that the notifier is installed
only once.
Cc: Sebastian Reichel <[email protected]>
Signed-off-by: Sudeep Holla <[email protected]>
Fixes: 46c99ac66222 ("power/reset: vexpress: Register with kernel restart handler")
Signed-off-by: Sebastian Reichel <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/power/reset/vexpress-poweroff.c | 12 ++++++++----
1 file changed, 8 insertions(+), 4 deletions(-)
--- a/drivers/power/reset/vexpress-poweroff.c
+++ b/drivers/power/reset/vexpress-poweroff.c
@@ -35,6 +35,7 @@ static void vexpress_reset_do(struct dev
}
static struct device *vexpress_power_off_device;
+static atomic_t vexpress_restart_nb_refcnt = ATOMIC_INIT(0);
static void vexpress_power_off(void)
{
@@ -99,10 +100,13 @@ static int _vexpress_register_restart_ha
int err;
vexpress_restart_device = dev;
- err = register_restart_handler(&vexpress_restart_nb);
- if (err) {
- dev_err(dev, "cannot register restart handler (err=%d)\n", err);
- return err;
+ if (atomic_inc_return(&vexpress_restart_nb_refcnt) == 1) {
+ err = register_restart_handler(&vexpress_restart_nb);
+ if (err) {
+ dev_err(dev, "cannot register restart handler (err=%d)\n", err);
+ atomic_dec(&vexpress_restart_nb_refcnt);
+ return err;
+ }
}
device_create_file(dev, &dev_attr_active);
On Tue, Oct 02, 2018 at 06:23:21AM -0700, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 4.14.74 release.
> There are 137 patches in this series, all will be posted as a response
> to this one. If anyone has any issues with these being applied, please
> let me know.
>
> Responses should be made by Thu Oct 4 13:24:18 UTC 2018.
> Anything received after that time might be too late.
>
> The whole patch series can be found in one patch at:
> https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.14.74-rc1.gz
> or in the git tree and branch at:
> git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.14.y
> and the diffstat can be found below.
>
> thanks,
>
> greg k-h
>
Merged, compiled, and installed onto my Raspberry Pi.
No initial issues noticed in dmesg or general usage.
Thanks!
Nathan
On 10/02/2018 07:23 AM, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 4.14.74 release.
> There are 137 patches in this series, all will be posted as a response
> to this one. If anyone has any issues with these being applied, please
> let me know.
>
> Responses should be made by Thu Oct 4 13:24:18 UTC 2018.
> Anything received after that time might be too late.
>
> The whole patch series can be found in one patch at:
> https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.14.74-rc1.gz
> or in the git tree and branch at:
> git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.14.y
> and the diffstat can be found below.
>
> thanks,
>
> greg k-h
>
Compiled and booted on my test system. No dmesg regressions.
thanks,
-- Shuah
On Tue, Oct 02, 2018 at 12:19:40PM -0700, Nathan Chancellor wrote:
> On Tue, Oct 02, 2018 at 06:23:21AM -0700, Greg Kroah-Hartman wrote:
> > This is the start of the stable review cycle for the 4.14.74 release.
> > There are 137 patches in this series, all will be posted as a response
> > to this one. If anyone has any issues with these being applied, please
> > let me know.
> >
> > Responses should be made by Thu Oct 4 13:24:18 UTC 2018.
> > Anything received after that time might be too late.
> >
> > The whole patch series can be found in one patch at:
> > https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.14.74-rc1.gz
> > or in the git tree and branch at:
> > git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.14.y
> > and the diffstat can be found below.
> >
> > thanks,
> >
> > greg k-h
> >
>
> Merged, compiled, and installed onto my Raspberry Pi.
>
> No initial issues noticed in dmesg or general usage.
thanks for testing 2 of these and letting me know.
greg k-h
On 10/02/2018 06:23 AM, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 4.14.74 release.
> There are 137 patches in this series, all will be posted as a response
> to this one. If anyone has any issues with these being applied, please
> let me know.
>
> Responses should be made by Thu Oct 4 13:24:18 UTC 2018.
> Anything received after that time might be too late.
>
Build results:
total: 151 pass: 151 fail: 0
Qemu test results:
total: 318 pass: 317 fail: 1
Failed tests:
powerpc:g3beige:ppc_book3s_defconfig:nosmp:ide:rootfs
Details are available at https://kerneltests.org/builders/.
Guenter
On Tue, Oct 02, 2018 at 06:23:21AM -0700, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 4.14.74 release.
> There are 137 patches in this series, all will be posted as a response
> to this one. If anyone has any issues with these being applied, please
> let me know.
>
> Responses should be made by Thu Oct 4 13:24:18 UTC 2018.
> Anything received after that time might be too late.
Results from Linaro’s test farm.
No regressions on arm64, arm, x86_64, and i386.
Summary
------------------------------------------------------------------------
kernel: 4.14.74-rc1
git repo: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
git branch: linux-4.14.y
git commit: 34a960c72ac4156519f59391bcab9b0677e46bc9
git describe: v4.14.73-139-g34a960c72ac4
Test details: https://qa-reports.linaro.org/lkft/linux-stable-rc-4.14-oe/build/v4.14.73-139-g34a960c72ac4
No regressions (compared to build v4.14.73)
------------------------------------------------------------------------
Ran 21220 total tests in the following environments and test suites.
Environments
--------------
- dragonboard-410c - arm64
- hi6220-hikey - arm64
- i386
- juno-r2 - arm64
- qemu_arm
- qemu_arm64
- qemu_i386
- qemu_x86_64
- x15 - arm
- x86_64
Test Suites
-----------
* boot
* kselftest
* libhugetlbfs
* ltp-cap_bounds-tests
* ltp-containers-tests
* ltp-cve-tests
* ltp-fcntl-locktests-tests
* ltp-filecaps-tests
* ltp-fs-tests
* ltp-fs_bind-tests
* ltp-fs_perms_simple-tests
* ltp-fsx-tests
* ltp-hugetlb-tests
* ltp-io-tests
* ltp-ipc-tests
* ltp-math-tests
* ltp-nptl-tests
* ltp-pty-tests
* ltp-sched-tests
* ltp-securebits-tests
* ltp-syscalls-tests
* ltp-timers-tests
* ltp-open-posix-tests
* kselftest-vsyscall-mode-native
* kselftest-vsyscall-mode-none
--
Linaro LKFT
https://lkft.linaro.org
On 02/10/18 14:23, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 4.14.74 release.
> There are 137 patches in this series, all will be posted as a response
> to this one. If anyone has any issues with these being applied, please
> let me know.
>
> Responses should be made by Thu Oct 4 13:24:18 UTC 2018.
> Anything received after that time might be too late.
All tests are passing for Tegra ...
Test results for stable-v4.14:
8 builds: 8 pass, 0 fail
8 boots: 8 pass, 0 fail
14 tests: 14 pass, 0 fail
Linux version: 4.14.74-rc1-g3fa7781
Boards tested: tegra124-jetson-tk1, tegra20-ventana,
tegra210-p2371-2180, tegra30-cardhu-a04
Cheers
Jon
--
nvpublic
On Thu, Oct 04, 2018 at 01:42:48PM +0100, Jon Hunter wrote:
>
> On 02/10/18 14:23, Greg Kroah-Hartman wrote:
> > This is the start of the stable review cycle for the 4.14.74 release.
> > There are 137 patches in this series, all will be posted as a response
> > to this one. If anyone has any issues with these being applied, please
> > let me know.
> >
> > Responses should be made by Thu Oct 4 13:24:18 UTC 2018.
> > Anything received after that time might be too late.
>
> All tests are passing for Tegra ...
>
> Test results for stable-v4.14:
> 8 builds: 8 pass, 0 fail
> 8 boots: 8 pass, 0 fail
> 14 tests: 14 pass, 0 fail
>
> Linux version: 4.14.74-rc1-g3fa7781
> Boards tested: tegra124-jetson-tk1, tegra20-ventana,
> tegra210-p2371-2180, tegra30-cardhu-a04
>
Wonderful, thanks for testing and letting me know.
greg k-h