This patch series intends to add imx7ulp clk support.
i.MX7ULP Clock functions are under joint control of the System
Clock Generation (SCG) modules, Peripheral Clock Control (PCC)
modules, and Core Mode Controller (CMC)1 blocks
The clocking scheme provides clear separation between M4 domain
and A7 domain. Except for a few clock sources shared between two
domains, such as the System Oscillator clock, the Slow IRC (SIRC),
and and the Fast IRC clock (FIRCLK), clock sources and clock
management are separated and contained within each domain.
M4 clock management consists of SCG0, PCC0, PCC1, and CMC0 modules.
A7 clock management consists of SCG1, PCC2, PCC3, and CMC1 modules.
Note: this series only adds A7 clock domain support as M4 clock
domain will be handled by M4 seperately.
Change Log:
v5->v6:
* move gatable divider from common divider to imx specfic folder(suggested by Michael)
* a small update of PATCH 9 for ddr/firc/dpll/sosc clocks to use divider table
v4->v5:
* rename to clk-composite-7ulp.c as we have another
clk-composite-8m.c, function name also changed accordingly
* binding doc updated with adding input clocks for PCC module
v3->v4:
* update after changing scg and pcc into separete nodes according to
Rob's suggestion
v2->v3:
* Patch 1 changed on: 1) split normal and gate ops 2) fix the possible racy
Others no changes.
v1->v2:
* add enable/disable for the type of CLK_DIVIDER_ZERO_GATE dividers
* use clk_hw apis to register clocks
* use of_clk_add_hw_provider
* split the clocks register process into two parts: early part for possible
timers clocks registered by CLK_OF_DECLARE_DRIVER and the later part for
the left normal peripheral clocks registered by a platform driver.
Dong Aisheng (9):
clk: imx: add gatable clock divider support
clk: fractional-divider: add CLK_FRAC_DIVIDER_ZERO_BASED flag support
clk: imx: add pllv4 support
clk: imx: add pfdv2 support
clk: imx: add imx7ulp composite clk support
dt-bindings: clock: add imx7ulp clock binding doc
clk: imx: make mux parent strings const
clk: imx: implement new clk_hw based APIs
clk: imx: add imx7ulp clk driver
.../devicetree/bindings/clock/imx7ulp-clock.txt | 104 ++++++++++
drivers/clk/clk-fractional-divider.c | 10 +
drivers/clk/imx/Makefile | 7 +-
drivers/clk/imx/clk-busy.c | 2 +-
drivers/clk/imx/clk-composite-7ulp.c | 85 ++++++++
drivers/clk/imx/clk-divider-gate.c | 219 ++++++++++++++++++++
drivers/clk/imx/clk-fixup-mux.c | 2 +-
drivers/clk/imx/clk-imx7ulp.c | 220 +++++++++++++++++++++
drivers/clk/imx/clk-pfdv2.c | 201 +++++++++++++++++++
drivers/clk/imx/clk-pllv4.c | 182 +++++++++++++++++
drivers/clk/imx/clk.c | 22 +++
drivers/clk/imx/clk.h | 96 ++++++++-
include/dt-bindings/clock/imx7ulp-clock.h | 109 ++++++++++
include/linux/clk-provider.h | 8 +
14 files changed, 1257 insertions(+), 10 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/imx7ulp-clock.txt
create mode 100644 drivers/clk/imx/clk-composite-7ulp.c
create mode 100644 drivers/clk/imx/clk-divider-gate.c
create mode 100644 drivers/clk/imx/clk-imx7ulp.c
create mode 100644 drivers/clk/imx/clk-pfdv2.c
create mode 100644 drivers/clk/imx/clk-pllv4.c
create mode 100644 include/dt-bindings/clock/imx7ulp-clock.h
--
2.7.4
For dividers with zero indicating clock is disabled, instead of giving a
warning each time like "clkx: Zero divisor and CLK_DIVIDER_ALLOW_ZERO not
set" in exist code, we'd like to introduce enable/disable function for it.
e.g.
000b - Clock disabled
001b - Divide by 1
010b - Divide by 2
...
Set rate when the clk is disabled will cache the rate request and only
when the clk is enabled will the driver actually program the hardware to
have the requested divider value. Similarly, when the clk is disabled we'll
write a 0 there, but when the clk is enabled we'll restore whatever rate
(divider) was chosen last.
It does mean that recalc rate will be sort of odd, because when the clk is
off it will return 0, and when the clk is on it will return the right rate.
So to make things work, we'll need to return the cached rate in recalc rate
when the clk is off and read the hardware when the clk is on.
NOTE for the default off divider, the recalc rate will still return 0 as
there's still no proper preset rate. Enable such divider will give user
a reminder error message.
Cc: Stephen Boyd <[email protected]>
Cc: Michael Turquette <[email protected]>
Cc: Shawn Guo <[email protected]>
Signed-off-by: Dong Aisheng <[email protected]>
---
ChangeLog:
v5->v6:
* move gatable divider code into imx specific clock folder as suggested
by Michael. Patch title also updated accordingly.
v4->v5:
* no changes
v3->v4:
* no changes
v2->v3:
* split normal and gate ops
* fix the possible racy
v1->v2:
* add enable/disable for the type of CLK_DIVIDER_ZERO_GATE dividers
---
drivers/clk/imx/Makefile | 1 +
drivers/clk/imx/clk-divider-gate.c | 219 +++++++++++++++++++++++++++++++++++++
drivers/clk/imx/clk.h | 4 +
3 files changed, 224 insertions(+)
create mode 100644 drivers/clk/imx/clk-divider-gate.c
diff --git a/drivers/clk/imx/Makefile b/drivers/clk/imx/Makefile
index 8c3baa7..077e732 100644
--- a/drivers/clk/imx/Makefile
+++ b/drivers/clk/imx/Makefile
@@ -4,6 +4,7 @@ obj-y += \
clk.o \
clk-busy.o \
clk-cpu.o \
+ clk-divider-gate.o \
clk-fixup-div.o \
clk-fixup-mux.o \
clk-gate-exclusive.o \
diff --git a/drivers/clk/imx/clk-divider-gate.c b/drivers/clk/imx/clk-divider-gate.c
new file mode 100644
index 0000000..b48fba2
--- /dev/null
+++ b/drivers/clk/imx/clk-divider-gate.c
@@ -0,0 +1,219 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 NXP.
+ * Dong Aisheng <[email protected]>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+
+struct clk_divider_gate {
+ struct clk_divider divider;
+ u32 cached_val;
+};
+
+static inline struct clk_divider_gate *to_clk_divider_gate(struct clk_hw *hw)
+{
+ struct clk_divider *div = to_clk_divider(hw);
+
+ return container_of(div, struct clk_divider_gate, divider);
+}
+
+static unsigned long clk_divider_gate_recalc_rate_ro(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct clk_divider *div = to_clk_divider(hw);
+ unsigned int val;
+
+ val = clk_readl(div->reg) >> div->shift;
+ val &= clk_div_mask(div->width);
+ if (!val)
+ return 0;
+
+ return divider_recalc_rate(hw, parent_rate, val, div->table,
+ div->flags, div->width);
+}
+
+static unsigned long clk_divider_gate_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct clk_divider_gate *div_gate = to_clk_divider_gate(hw);
+ struct clk_divider *div = to_clk_divider(hw);
+ unsigned long flags = 0;
+ unsigned int val;
+
+ spin_lock_irqsave(div->lock, flags);
+
+ if (!clk_hw_is_enabled(hw)) {
+ val = div_gate->cached_val;
+ } else {
+ val = clk_readl(div->reg) >> div->shift;
+ val &= clk_div_mask(div->width);
+ }
+
+ spin_unlock_irqrestore(div->lock, flags);
+
+ if (!val)
+ return 0;
+
+ return divider_recalc_rate(hw, parent_rate, val, div->table,
+ div->flags, div->width);
+}
+
+static long clk_divider_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *prate)
+{
+ return clk_divider_ops.round_rate(hw, rate, prate);
+}
+
+static int clk_divider_gate_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct clk_divider_gate *div_gate = to_clk_divider_gate(hw);
+ struct clk_divider *div = to_clk_divider(hw);
+ unsigned long flags = 0;
+ int value;
+ u32 val;
+
+ value = divider_get_val(rate, parent_rate, div->table,
+ div->width, div->flags);
+ if (value < 0)
+ return value;
+
+ spin_lock_irqsave(div->lock, flags);
+
+ if (clk_hw_is_enabled(hw)) {
+ val = clk_readl(div->reg);
+ val &= ~(clk_div_mask(div->width) << div->shift);
+ val |= (u32)value << div->shift;
+ clk_writel(val, div->reg);
+ } else {
+ div_gate->cached_val = value;
+ }
+
+ spin_unlock_irqrestore(div->lock, flags);
+
+ return 0;
+}
+
+static int clk_divider_enable(struct clk_hw *hw)
+{
+ struct clk_divider_gate *div_gate = to_clk_divider_gate(hw);
+ struct clk_divider *div = to_clk_divider(hw);
+ unsigned long flags = 0;
+ u32 val;
+
+ if (!div_gate->cached_val) {
+ pr_err("%s: no valid preset rate\n", clk_hw_get_name(hw));
+ return -EINVAL;
+ }
+
+ spin_lock_irqsave(div->lock, flags);
+ /* restore div val */
+ val = clk_readl(div->reg);
+ val |= div_gate->cached_val << div->shift;
+ clk_writel(val, div->reg);
+
+ spin_unlock_irqrestore(div->lock, flags);
+
+ return 0;
+}
+
+static void clk_divider_disable(struct clk_hw *hw)
+{
+ struct clk_divider_gate *div_gate = to_clk_divider_gate(hw);
+ struct clk_divider *div = to_clk_divider(hw);
+ unsigned long flags = 0;
+ u32 val;
+
+ spin_lock_irqsave(div->lock, flags);
+
+ /* store the current div val */
+ val = clk_readl(div->reg) >> div->shift;
+ val &= clk_div_mask(div->width);
+ div_gate->cached_val = val;
+ clk_writel(0, div->reg);
+
+ spin_unlock_irqrestore(div->lock, flags);
+}
+
+static int clk_divider_is_enabled(struct clk_hw *hw)
+{
+ struct clk_divider *div = to_clk_divider(hw);
+ u32 val;
+
+ val = clk_readl(div->reg) >> div->shift;
+ val &= clk_div_mask(div->width);
+
+ return val ? 1 : 0;
+}
+
+static const struct clk_ops clk_divider_gate_ro_ops = {
+ .recalc_rate = clk_divider_gate_recalc_rate_ro,
+ .round_rate = clk_divider_round_rate,
+};
+
+static const struct clk_ops clk_divider_gate_ops = {
+ .recalc_rate = clk_divider_gate_recalc_rate,
+ .round_rate = clk_divider_round_rate,
+ .set_rate = clk_divider_gate_set_rate,
+ .enable = clk_divider_enable,
+ .disable = clk_divider_disable,
+ .is_enabled = clk_divider_is_enabled,
+};
+
+/*
+ * NOTE: In order to resue the most code from the common divider,
+ * we also design our divider following the way that provids an extra
+ * clk_divider_flags, however it's fixed to CLK_DIVIDER_ONE_BASED by
+ * default as our HW is. Besides that it supports only CLK_DIVIDER_READ_ONLY
+ * flag which can be specified by user flexibly.
+ */
+struct clk_hw *imx_clk_divider_gate(const char *name, const char *parent_name,
+ unsigned long flags, void __iomem *reg,
+ u8 shift, u8 width, u8 clk_divider_flags,
+ const struct clk_div_table *table,
+ spinlock_t *lock)
+{
+ struct clk_init_data init;
+ struct clk_divider_gate *div_gate;
+ struct clk_hw *hw;
+ u32 val;
+ int ret;
+
+ div_gate = kzalloc(sizeof(*div_gate), GFP_KERNEL);
+ if (!div_gate)
+ return ERR_PTR(-ENOMEM);
+
+ init.name = name;
+ if (clk_divider_flags & CLK_DIVIDER_READ_ONLY)
+ init.ops = &clk_divider_gate_ro_ops;
+ else
+ init.ops = &clk_divider_gate_ops;
+ init.flags = flags;
+ init.parent_names = parent_name ? &parent_name : NULL;
+ init.num_parents = parent_name ? 1 : 0;
+
+ div_gate->divider.reg = reg;
+ div_gate->divider.shift = shift;
+ div_gate->divider.width = width;
+ div_gate->divider.lock = lock;
+ div_gate->divider.table = table;
+ div_gate->divider.hw.init = &init;
+ div_gate->divider.flags = CLK_DIVIDER_ONE_BASED | clk_divider_flags;
+ /* cache gate status */
+ val = clk_readl(reg) >> shift;
+ val &= clk_div_mask(width);
+ div_gate->cached_val = val;
+
+ hw = &div_gate->divider.hw;
+ ret = clk_hw_register(NULL, hw);
+ if (ret) {
+ kfree(div_gate);
+ hw = ERR_PTR(ret);
+ }
+
+ return hw;
+}
diff --git a/drivers/clk/imx/clk.h b/drivers/clk/imx/clk.h
index 8076ec0..8e65282 100644
--- a/drivers/clk/imx/clk.h
+++ b/drivers/clk/imx/clk.h
@@ -220,4 +220,8 @@ struct clk *imx_clk_cpu(const char *name, const char *parent_name,
struct clk *div, struct clk *mux, struct clk *pll,
struct clk *step);
+struct clk_hw *imx_clk_divider_gate(const char *name, const char *parent_name,
+ unsigned long flags, void __iomem *reg, u8 shift, u8 width,
+ u8 clk_divider_flags, const struct clk_div_table *table,
+ spinlock_t *lock);
#endif
--
2.7.4
The pfdv2 is designed for PLL Fractional Divide (PFD) observed in System
Clock Generation (SCG) module in IMX ULP SoC series. e.g. i.MX7ULP.
NOTE pfdv2 can only be operated when clk is gated.
Cc: Stephen Boyd <[email protected]>
Cc: Michael Turquette <[email protected]>
Cc: Shawn Guo <[email protected]>
Cc: Anson Huang <[email protected]>
Cc: Bai Ping <[email protected]>
Signed-off-by: Dong Aisheng <[email protected]>
---
ChangeLog:
v3->v4:
* no changes
v2->v3:
* no changes
v1->v2:
* change to readl_poll_timeout
* add pfd lock to protect share reg access between rate and enable/disable
operations and multiple pfd instances.
* use clk_hw_register
---
drivers/clk/imx/Makefile | 3 +-
drivers/clk/imx/clk-pfdv2.c | 201 ++++++++++++++++++++++++++++++++++++++++++++
drivers/clk/imx/clk.h | 3 +
3 files changed, 206 insertions(+), 1 deletion(-)
create mode 100644 drivers/clk/imx/clk-pfdv2.c
diff --git a/drivers/clk/imx/Makefile b/drivers/clk/imx/Makefile
index 4cac28b..e7248de 100644
--- a/drivers/clk/imx/Makefile
+++ b/drivers/clk/imx/Makefile
@@ -13,7 +13,8 @@ obj-y += \
clk-pllv2.o \
clk-pllv3.o \
clk-pllv4.o \
- clk-pfd.o
+ clk-pfd.o \
+ clk-pfdv2.o
obj-$(CONFIG_SOC_IMX1) += clk-imx1.o
obj-$(CONFIG_SOC_IMX21) += clk-imx21.o
diff --git a/drivers/clk/imx/clk-pfdv2.c b/drivers/clk/imx/clk-pfdv2.c
new file mode 100644
index 0000000..afb2904
--- /dev/null
+++ b/drivers/clk/imx/clk-pfdv2.c
@@ -0,0 +1,201 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Copyright 2017~2018 NXP
+ *
+ * Author: Dong Aisheng <[email protected]>
+ *
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/err.h>
+#include <linux/iopoll.h>
+#include <linux/slab.h>
+
+/**
+ * struct clk_pfdv2 - IMX PFD clock
+ * @clk_hw: clock source
+ * @reg: PFD register address
+ * @gate_bit: Gate bit offset
+ * @vld_bit: Valid bit offset
+ * @frac_off: PLL Fractional Divider offset
+ */
+
+struct clk_pfdv2 {
+ struct clk_hw hw;
+ void __iomem *reg;
+ u8 gate_bit;
+ u8 vld_bit;
+ u8 frac_off;
+};
+
+#define to_clk_pfdv2(_hw) container_of(_hw, struct clk_pfdv2, hw)
+
+#define CLK_PFDV2_FRAC_MASK 0x3f
+
+#define LOCK_TIMEOUT_US USEC_PER_MSEC
+
+static DEFINE_SPINLOCK(pfd_lock);
+
+static int clk_pfdv2_wait(struct clk_pfdv2 *pfd)
+{
+ u32 val;
+
+ return readl_poll_timeout(pfd->reg, val, val & pfd->vld_bit,
+ 0, LOCK_TIMEOUT_US);
+}
+
+static int clk_pfdv2_enable(struct clk_hw *hw)
+{
+ struct clk_pfdv2 *pfd = to_clk_pfdv2(hw);
+ unsigned long flags;
+ u32 val;
+
+ spin_lock_irqsave(&pfd_lock, flags);
+ val = readl_relaxed(pfd->reg);
+ val &= ~pfd->gate_bit;
+ writel_relaxed(val, pfd->reg);
+ spin_unlock_irqrestore(&pfd_lock, flags);
+
+ return clk_pfdv2_wait(pfd);
+}
+
+static void clk_pfdv2_disable(struct clk_hw *hw)
+{
+ struct clk_pfdv2 *pfd = to_clk_pfdv2(hw);
+ unsigned long flags;
+ u32 val;
+
+ spin_lock_irqsave(&pfd_lock, flags);
+ val = readl_relaxed(pfd->reg);
+ val |= pfd->gate_bit;
+ writel_relaxed(val, pfd->reg);
+ spin_unlock_irqrestore(&pfd_lock, flags);
+}
+
+static unsigned long clk_pfdv2_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct clk_pfdv2 *pfd = to_clk_pfdv2(hw);
+ u64 tmp = parent_rate;
+ u8 frac;
+
+ frac = (readl_relaxed(pfd->reg) >> pfd->frac_off)
+ & CLK_PFDV2_FRAC_MASK;
+
+ if (!frac) {
+ pr_debug("clk_pfdv2: %s invalid pfd frac value 0\n",
+ clk_hw_get_name(hw));
+ return 0;
+ }
+
+ tmp *= 18;
+ do_div(tmp, frac);
+
+ return tmp;
+}
+
+static long clk_pfdv2_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *prate)
+{
+ u64 tmp = *prate;
+ u8 frac;
+
+ tmp = tmp * 18 + rate / 2;
+ do_div(tmp, rate);
+ frac = tmp;
+
+ if (frac < 12)
+ frac = 12;
+ else if (frac > 35)
+ frac = 35;
+
+ tmp = *prate;
+ tmp *= 18;
+ do_div(tmp, frac);
+
+ return tmp;
+}
+
+static int clk_pfdv2_is_enabled(struct clk_hw *hw)
+{
+ struct clk_pfdv2 *pfd = to_clk_pfdv2(hw);
+
+ if (readl_relaxed(pfd->reg) & pfd->gate_bit)
+ return 0;
+
+ return 1;
+}
+
+static int clk_pfdv2_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct clk_pfdv2 *pfd = to_clk_pfdv2(hw);
+ unsigned long flags;
+ u64 tmp = parent_rate;
+ u32 val;
+ u8 frac;
+
+ tmp = tmp * 18 + rate / 2;
+ do_div(tmp, rate);
+ frac = tmp;
+ if (frac < 12)
+ frac = 12;
+ else if (frac > 35)
+ frac = 35;
+
+ spin_lock_irqsave(&pfd_lock, flags);
+ val = readl_relaxed(pfd->reg);
+ val &= ~(CLK_PFDV2_FRAC_MASK << pfd->frac_off);
+ val |= frac << pfd->frac_off;
+ writel_relaxed(val, pfd->reg);
+ spin_unlock_irqrestore(&pfd_lock, flags);
+
+ return 0;
+}
+
+static const struct clk_ops clk_pfdv2_ops = {
+ .enable = clk_pfdv2_enable,
+ .disable = clk_pfdv2_disable,
+ .recalc_rate = clk_pfdv2_recalc_rate,
+ .round_rate = clk_pfdv2_round_rate,
+ .set_rate = clk_pfdv2_set_rate,
+ .is_enabled = clk_pfdv2_is_enabled,
+};
+
+struct clk_hw *imx_clk_pfdv2(const char *name, const char *parent_name,
+ void __iomem *reg, u8 idx)
+{
+ struct clk_init_data init;
+ struct clk_pfdv2 *pfd;
+ struct clk_hw *hw;
+ int ret;
+
+ WARN_ON(idx > 3);
+
+ pfd = kzalloc(sizeof(*pfd), GFP_KERNEL);
+ if (!pfd)
+ return ERR_PTR(-ENOMEM);
+
+ pfd->reg = reg;
+ pfd->gate_bit = 1 << ((idx + 1) * 8 - 1);
+ pfd->vld_bit = pfd->gate_bit - 1;
+ pfd->frac_off = idx * 8;
+
+ init.name = name;
+ init.ops = &clk_pfdv2_ops;
+ init.parent_names = &parent_name;
+ init.num_parents = 1;
+ init.flags = CLK_SET_RATE_GATE;
+
+ pfd->hw.init = &init;
+
+ hw = &pfd->hw;
+ ret = clk_hw_register(NULL, hw);
+ if (ret) {
+ kfree(pfd);
+ hw = ERR_PTR(ret);
+ }
+
+ return hw;
+}
diff --git a/drivers/clk/imx/clk.h b/drivers/clk/imx/clk.h
index 1e11eb7..ebeb754 100644
--- a/drivers/clk/imx/clk.h
+++ b/drivers/clk/imx/clk.h
@@ -60,6 +60,9 @@ struct clk *imx_clk_gate_exclusive(const char *name, const char *parent,
struct clk *imx_clk_pfd(const char *name, const char *parent_name,
void __iomem *reg, u8 idx);
+struct clk_hw *imx_clk_pfdv2(const char *name, const char *parent_name,
+ void __iomem *reg, u8 idx);
+
struct clk *imx_clk_busy_divider(const char *name, const char *parent_name,
void __iomem *reg, u8 shift, u8 width,
void __iomem *busy_reg, u8 busy_shift);
--
2.7.4
The imx composite clk is designed for Peripheral Clock Control (PCC)
module observed in IMX ULP SoC series.
NOTE pcc can only be operated when clk is gated.
Cc: Stephen Boyd <[email protected]>
Cc: Michael Turquette <[email protected]>
Cc: Shawn Guo <[email protected]>
Cc: Anson Huang <[email protected]>
Cc: Bai Ping <[email protected]>
Signed-off-by: Dong Aisheng <[email protected]>
---
ChangeLog:
v4->v5:
* rename to clk-composite-7ulp.c as we have another
clk-composite-8m.c, function name also changed accordingly
v3->v4:
* no changes
v2->v3:
* no changes
v1->v2:
* remove an unneeded blank line change
* use clk_hw_register
---
drivers/clk/imx/Makefile | 1 +
drivers/clk/imx/clk-composite-7ulp.c | 85 ++++++++++++++++++++++++++++++++++++
drivers/clk/imx/clk.h | 6 +++
3 files changed, 92 insertions(+)
create mode 100644 drivers/clk/imx/clk-composite-7ulp.c
diff --git a/drivers/clk/imx/Makefile b/drivers/clk/imx/Makefile
index e7248de..a5cab3e 100644
--- a/drivers/clk/imx/Makefile
+++ b/drivers/clk/imx/Makefile
@@ -4,6 +4,7 @@ obj-y += \
clk.o \
clk-busy.o \
clk-cpu.o \
+ clk-composite-7ulp.o \
clk-divider-gate.o \
clk-fixup-div.o \
clk-fixup-mux.o \
diff --git a/drivers/clk/imx/clk-composite-7ulp.c b/drivers/clk/imx/clk-composite-7ulp.c
new file mode 100644
index 0000000..22f679c
--- /dev/null
+++ b/drivers/clk/imx/clk-composite-7ulp.c
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Copyright 2017~2018 NXP
+ *
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/err.h>
+#include <linux/slab.h>
+
+#define PCG_PCS_SHIFT 24
+#define PCG_PCS_MASK 0x7
+#define PCG_CGC_SHIFT 30
+#define PCG_FRAC_SHIFT 3
+#define PCG_FRAC_WIDTH 1
+#define PCG_FRAC_MASK BIT(3)
+#define PCG_PCD_SHIFT 0
+#define PCG_PCD_WIDTH 3
+#define PCG_PCD_MASK 0x7
+
+struct clk_hw *imx7ulp_clk_composite(const char *name,
+ const char * const *parent_names,
+ int num_parents, bool mux_present,
+ bool rate_present, bool gate_present,
+ void __iomem *reg)
+{
+ struct clk_hw *mux_hw = NULL, *fd_hw = NULL, *gate_hw = NULL;
+ struct clk_fractional_divider *fd = NULL;
+ struct clk_gate *gate = NULL;
+ struct clk_mux *mux = NULL;
+ struct clk_hw *hw;
+
+ if (mux_present) {
+ mux = kzalloc(sizeof(*mux), GFP_KERNEL);
+ if (!mux)
+ return ERR_PTR(-ENOMEM);
+ mux_hw = &mux->hw;
+ mux->reg = reg;
+ mux->shift = PCG_PCS_SHIFT;
+ mux->mask = PCG_PCS_MASK;
+ }
+
+ if (rate_present) {
+ fd = kzalloc(sizeof(*fd), GFP_KERNEL);
+ if (!fd) {
+ kfree(mux);
+ return ERR_PTR(-ENOMEM);
+ }
+ fd_hw = &fd->hw;
+ fd->reg = reg;
+ fd->mshift = PCG_FRAC_SHIFT;
+ fd->mwidth = PCG_FRAC_WIDTH;
+ fd->mmask = PCG_FRAC_MASK;
+ fd->nshift = PCG_PCD_SHIFT;
+ fd->nwidth = PCG_PCD_WIDTH;
+ fd->nmask = PCG_PCD_MASK;
+ fd->flags = CLK_FRAC_DIVIDER_ZERO_BASED;
+ }
+
+ if (gate_present) {
+ gate = kzalloc(sizeof(*gate), GFP_KERNEL);
+ if (!gate) {
+ kfree(mux);
+ kfree(fd);
+ return ERR_PTR(-ENOMEM);
+ }
+ gate_hw = &gate->hw;
+ gate->reg = reg;
+ gate->bit_idx = PCG_CGC_SHIFT;
+ }
+
+ hw = clk_hw_register_composite(NULL, name, parent_names, num_parents,
+ mux_hw, &clk_mux_ops, fd_hw,
+ &clk_fractional_divider_ops, gate_hw,
+ &clk_gate_ops, CLK_SET_RATE_GATE |
+ CLK_SET_PARENT_GATE);
+ if (IS_ERR(hw)) {
+ kfree(mux);
+ kfree(fd);
+ kfree(gate);
+ }
+
+ return hw;
+}
diff --git a/drivers/clk/imx/clk.h b/drivers/clk/imx/clk.h
index ebeb754..2e3bcfa 100644
--- a/drivers/clk/imx/clk.h
+++ b/drivers/clk/imx/clk.h
@@ -71,6 +71,12 @@ struct clk *imx_clk_busy_mux(const char *name, void __iomem *reg, u8 shift,
u8 width, void __iomem *busy_reg, u8 busy_shift,
const char **parent_names, int num_parents);
+struct clk_hw *imx7ulp_clk_composite(const char *name,
+ const char * const *parent_names,
+ int num_parents, bool mux_present,
+ bool rate_present, bool gate_present,
+ void __iomem *reg);
+
struct clk *imx_clk_fixup_divider(const char *name, const char *parent,
void __iomem *reg, u8 shift, u8 width,
void (*fixup)(u32 *val));
--
2.7.4
i.MX7ULP Clock functions are under joint control of the System
Clock Generation (SCG) modules, Peripheral Clock Control (PCC)
modules, and Core Mode Controller (CMC)1 blocks
Note IMX7ULP has two clock domains: M4 and A7. This binding doc
is only for A7 clock domain.
Cc: Rob Herring <[email protected]>
Cc: Mark Rutland <[email protected]>
Cc: Stephen Boyd <[email protected]>
Cc: Michael Turquette <[email protected]>
Cc: Shawn Guo <[email protected]>
Cc: Anson Huang <[email protected]>
Cc: Bai Ping <[email protected]>
Signed-off-by: Dong Aisheng <[email protected]>
---
ChangeLog:
v4->v5:
* fix a typo that clock-name -> clock-names
* one compatible string per line
* add input clocks for pcc2/3
v3->v4:
* make scg, pcc separate nodes according to Rob's suggestion
v2->v3:
* no changes
v1->v2: no changes
---
.../devicetree/bindings/clock/imx7ulp-clock.txt | 104 ++++++++++++++++++++
include/dt-bindings/clock/imx7ulp-clock.h | 109 +++++++++++++++++++++
2 files changed, 213 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/imx7ulp-clock.txt
create mode 100644 include/dt-bindings/clock/imx7ulp-clock.h
diff --git a/Documentation/devicetree/bindings/clock/imx7ulp-clock.txt b/Documentation/devicetree/bindings/clock/imx7ulp-clock.txt
new file mode 100644
index 0000000..a4f8cd4
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/imx7ulp-clock.txt
@@ -0,0 +1,104 @@
+* Clock bindings for Freescale i.MX7ULP
+
+i.MX7ULP Clock functions are under joint control of the System
+Clock Generation (SCG) modules, Peripheral Clock Control (PCC)
+modules, and Core Mode Controller (CMC)1 blocks
+
+The clocking scheme provides clear separation between M4 domain
+and A7 domain. Except for a few clock sources shared between two
+domains, such as the System Oscillator clock, the Slow IRC (SIRC),
+and and the Fast IRC clock (FIRCLK), clock sources and clock
+management are separated and contained within each domain.
+
+M4 clock management consists of SCG0, PCC0, PCC1, and CMC0 modules.
+A7 clock management consists of SCG1, PCC2, PCC3, and CMC1 modules.
+
+Note: this binding doc is only for A7 clock domain.
+
+System Clock Generation (SCG) modules:
+---------------------------------------------------------------------
+The System Clock Generation (SCG) is responsible for clock generation
+and distribution across this device. Functions performed by the SCG
+include: clock reference selection, generation of clock used to derive
+processor, system, peripheral bus and external memory interface clocks,
+source selection for peripheral clocks and control of power saving
+clock gating mode.
+
+Required properties:
+
+- compatible: Should be "fsl,imx7ulp-scg1".
+- reg : Should contain registers location and length.
+- #clock-cells: Should be <1>.
+- clocks: Should contain the fixed input clocks.
+- clock-names: Should contain the following clock names:
+ "rosc", "sosc", "sirc", "firc", "upll", "mpll".
+
+Peripheral Clock Control (PCC) modules:
+---------------------------------------------------------------------
+The Peripheral Clock Control (PCC) is responsible for clock selection,
+optional division and clock gating mode for peripherals in their
+respected power domain
+
+Required properties:
+- compatible: Should be one of:
+ "fsl,imx7ulp-pcc2",
+ "fsl,imx7ulp-pcc3".
+- reg : Should contain registers location and length.
+- #clock-cells: Should be <1>.
+- clocks: Should contain the fixed input clocks.
+- clock-names: Should contain the following clock names:
+ "nic1_bus_clk", "nic1_clk", "ddr_clk", "apll_pfd2",
+ "apll_pfd1", "apll_pfd0", "upll", "sosc_bus_clk",
+ "mpll", "firc_bus_clk", "rosc", "spll_bus_clk";
+
+The clock consumer should specify the desired clock by having the clock
+ID in its "clocks" phandle cell.
+See include/dt-bindings/clock/imx7ulp-clock.h
+for the full list of i.MX7ULP clock IDs of each module.
+
+Examples:
+
+#include <dt-bindings/clock/imx7ulp-clock.h>
+
+scg1: scg1@403e0000 {
+ compatible = "fsl,imx7ulp-scg1;
+ reg = <0x403e0000 0x10000>;
+ clocks = <&rosc>, <&sosc>, <&sirc>,
+ <&firc>, <&upll>, <&mpll>;
+ clock-names = "rosc", "sosc", "sirc",
+ "firc", "upll", "mpll";
+ #clock-cells = <1>;
+};
+
+pcc2: pcc2@403f0000 {
+ compatible = "fsl,imx7ulp-pcc2";
+ reg = <0x403f0000 0x10000>;
+ #clock-cells = <1>;
+ clocks = <&scg1 IMX7ULP_CLK_NIC1_BUS_DIV>,
+ <&scg1 IMX7ULP_CLK_NIC1_DIV>,
+ <&scg1 IMX7ULP_CLK_DDR_DIV>,
+ <&scg1 IMX7ULP_CLK_APLL_PFD2>,
+ <&scg1 IMX7ULP_CLK_APLL_PFD1>,
+ <&scg1 IMX7ULP_CLK_APLL_PFD0>,
+ <&scg1 IMX7ULP_CLK_UPLL>,
+ <&scg1 IMX7ULP_CLK_SOSC_BUS_CLK>,
+ <&scg1 IMX7ULP_CLK_MIPI_PLL>,
+ <&scg1 IMX7ULP_CLK_FIRC_BUS_CLK>,
+ <&scg1 IMX7ULP_CLK_ROSC>,
+ <&scg1 IMX7ULP_CLK_SPLL_BUS_CLK>;
+ clock-names = "nic1_bus_clk", "nic1_clk", "ddr_clk",
+ "apll_pfd2", "apll_pfd1", "apll_pfd0",
+ "upll", "sosc_bus_clk", "mpll",
+ "firc_bus_clk", "rosc", "spll_bus_clk";
+};
+
+usdhc1: usdhc@40380000 {
+ compatible = "fsl,imx7ulp-usdhc";
+ reg = <0x40380000 0x10000>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scg1 IMX7ULP_CLK_NIC1_BUS_DIV>,
+ <&scg1 IMX7ULP_CLK_NIC1_DIV>,
+ <&pcc2 IMX7ULP_CLK_USDHC1>;
+ clock-names ="ipg", "ahb", "per";
+ bus-width = <4>;
+};
diff --git a/include/dt-bindings/clock/imx7ulp-clock.h b/include/dt-bindings/clock/imx7ulp-clock.h
new file mode 100644
index 0000000..008c5ee
--- /dev/null
+++ b/include/dt-bindings/clock/imx7ulp-clock.h
@@ -0,0 +1,109 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Copyright 2017~2018 NXP
+ *
+ */
+
+#ifndef __DT_BINDINGS_CLOCK_IMX7ULP_H
+#define __DT_BINDINGS_CLOCK_IMX7ULP_H
+
+/* SCG1 */
+
+#define IMX7ULP_CLK_DUMMY 0
+#define IMX7ULP_CLK_ROSC 1
+#define IMX7ULP_CLK_SOSC 2
+#define IMX7ULP_CLK_FIRC 3
+#define IMX7ULP_CLK_SPLL_PRE_SEL 4
+#define IMX7ULP_CLK_SPLL_PRE_DIV 5
+#define IMX7ULP_CLK_SPLL 6
+#define IMX7ULP_CLK_SPLL_POST_DIV1 7
+#define IMX7ULP_CLK_SPLL_POST_DIV2 8
+#define IMX7ULP_CLK_SPLL_PFD0 9
+#define IMX7ULP_CLK_SPLL_PFD1 10
+#define IMX7ULP_CLK_SPLL_PFD2 11
+#define IMX7ULP_CLK_SPLL_PFD3 12
+#define IMX7ULP_CLK_SPLL_PFD_SEL 13
+#define IMX7ULP_CLK_SPLL_SEL 14
+#define IMX7ULP_CLK_APLL_PRE_SEL 15
+#define IMX7ULP_CLK_APLL_PRE_DIV 16
+#define IMX7ULP_CLK_APLL 17
+#define IMX7ULP_CLK_APLL_POST_DIV1 18
+#define IMX7ULP_CLK_APLL_POST_DIV2 19
+#define IMX7ULP_CLK_APLL_PFD0 20
+#define IMX7ULP_CLK_APLL_PFD1 21
+#define IMX7ULP_CLK_APLL_PFD2 22
+#define IMX7ULP_CLK_APLL_PFD3 23
+#define IMX7ULP_CLK_APLL_PFD_SEL 24
+#define IMX7ULP_CLK_APLL_SEL 25
+#define IMX7ULP_CLK_UPLL 26
+#define IMX7ULP_CLK_SYS_SEL 27
+#define IMX7ULP_CLK_CORE_DIV 28
+#define IMX7ULP_CLK_BUS_DIV 29
+#define IMX7ULP_CLK_PLAT_DIV 30
+#define IMX7ULP_CLK_DDR_SEL 31
+#define IMX7ULP_CLK_DDR_DIV 32
+#define IMX7ULP_CLK_NIC_SEL 33
+#define IMX7ULP_CLK_NIC0_DIV 34
+#define IMX7ULP_CLK_GPU_DIV 35
+#define IMX7ULP_CLK_NIC1_DIV 36
+#define IMX7ULP_CLK_NIC1_BUS_DIV 37
+#define IMX7ULP_CLK_NIC1_EXT_DIV 38
+#define IMX7ULP_CLK_MIPI_PLL 39
+#define IMX7ULP_CLK_SIRC 40
+#define IMX7ULP_CLK_SOSC_BUS_CLK 41
+#define IMX7ULP_CLK_FIRC_BUS_CLK 42
+#define IMX7ULP_CLK_SPLL_BUS_CLK 43
+
+#define IMX7ULP_CLK_SCG1_END 44
+
+/* PCC2 */
+#define IMX7ULP_CLK_DMA1 0
+#define IMX7ULP_CLK_RGPIO2P1 1
+#define IMX7ULP_CLK_FLEXBUS 2
+#define IMX7ULP_CLK_SEMA42_1 3
+#define IMX7ULP_CLK_DMA_MUX1 4
+#define IMX7ULP_CLK_SNVS 5
+#define IMX7ULP_CLK_CAAM 6
+#define IMX7ULP_CLK_LPTPM4 7
+#define IMX7ULP_CLK_LPTPM5 8
+#define IMX7ULP_CLK_LPIT1 9
+#define IMX7ULP_CLK_LPSPI2 10
+#define IMX7ULP_CLK_LPSPI3 11
+#define IMX7ULP_CLK_LPI2C4 12
+#define IMX7ULP_CLK_LPI2C5 13
+#define IMX7ULP_CLK_LPUART4 14
+#define IMX7ULP_CLK_LPUART5 15
+#define IMX7ULP_CLK_FLEXIO1 16
+#define IMX7ULP_CLK_USB0 17
+#define IMX7ULP_CLK_USB1 18
+#define IMX7ULP_CLK_USB_PHY 19
+#define IMX7ULP_CLK_USB_PL301 20
+#define IMX7ULP_CLK_USDHC0 21
+#define IMX7ULP_CLK_USDHC1 22
+#define IMX7ULP_CLK_WDG1 23
+#define IMX7ULP_CLK_WDG2 24
+
+#define IMX7ULP_CLK_PCC2_END 25
+
+/* PCC3 */
+#define IMX7ULP_CLK_LPTPM6 0
+#define IMX7ULP_CLK_LPTPM7 1
+#define IMX7ULP_CLK_LPI2C6 2
+#define IMX7ULP_CLK_LPI2C7 3
+#define IMX7ULP_CLK_LPUART6 4
+#define IMX7ULP_CLK_LPUART7 5
+#define IMX7ULP_CLK_VIU 6
+#define IMX7ULP_CLK_DSI 7
+#define IMX7ULP_CLK_LCDIF 8
+#define IMX7ULP_CLK_MMDC 9
+#define IMX7ULP_CLK_PCTLC 10
+#define IMX7ULP_CLK_PCTLD 11
+#define IMX7ULP_CLK_PCTLE 12
+#define IMX7ULP_CLK_PCTLF 13
+#define IMX7ULP_CLK_GPU3D 14
+#define IMX7ULP_CLK_GPU2D 15
+
+#define IMX7ULP_CLK_PCC3_END 16
+
+#endif /* __DT_BINDINGS_CLOCK_IMX7ULP_H */
--
2.7.4
i.MX7ULP Clock functions are under joint control of the System
Clock Generation (SCG) modules, Peripheral Clock Control (PCC)
modules, and Core Mode Controller (CMC)1 blocks
The clocking scheme provides clear separation between M4 domain
and A7 domain. Except for a few clock sources shared between two
domains, such as the System Oscillator clock, the Slow IRC (SIRC),
and and the Fast IRC clock (FIRCLK), clock sources and clock
management are separated and contained within each domain.
M4 clock management consists of SCG0, PCC0, PCC1, and CMC0 modules.
A7 clock management consists of SCG1, PCC2, PCC3, and CMC1 modules.
This driver only adds clock support in A7 domain.
Note that most clocks required to be operated when gated, e.g. pll,
pfd, pcc. And more special cases that scs/ddr/nic mux selecting
different clock source requires that clock to be enabled first,
then we need set CLK_OPS_PARENT_ENABLE flag for them properly.
Cc: Stephen Boyd <[email protected]>
Cc: Michael Turquette <[email protected]>
Cc: Shawn Guo <[email protected]>
Cc: Anson Huang <[email protected]>
Cc: Bai Ping <[email protected]>
Signed-off-by: Dong Aisheng <[email protected]>
---
ChangeLog:
v5->v6:
* sosc/firc/dpll/ddr clock should use divider table as they're not 1:1
v4->v5:
* clk-composite API name changed accordingly
v3->v4:
* update after changing scg and pcc into separete nodes according to
Rob's suggestion
v2->v3:
* no changes
v1->v2:
* use of_clk_add_hw_provider instead
* split the clocks register process into two parts: early part for possible
timers clocks registered by CLK_OF_DECLARE_DRIVER and the later part for
the left normal peripheral clocks registered by a platform driver.
---
drivers/clk/imx/Makefile | 1 +
drivers/clk/imx/clk-imx7ulp.c | 220 ++++++++++++++++++++++++++++++++++++++++++
2 files changed, 221 insertions(+)
create mode 100644 drivers/clk/imx/clk-imx7ulp.c
diff --git a/drivers/clk/imx/Makefile b/drivers/clk/imx/Makefile
index a5cab3e..615b413 100644
--- a/drivers/clk/imx/Makefile
+++ b/drivers/clk/imx/Makefile
@@ -30,4 +30,5 @@ obj-$(CONFIG_SOC_IMX6SLL) += clk-imx6sll.o
obj-$(CONFIG_SOC_IMX6SX) += clk-imx6sx.o
obj-$(CONFIG_SOC_IMX6UL) += clk-imx6ul.o
obj-$(CONFIG_SOC_IMX7D) += clk-imx7d.o
+obj-$(CONFIG_SOC_IMX7ULP) += clk-imx7ulp.o
obj-$(CONFIG_SOC_VF610) += clk-vf610.o
diff --git a/drivers/clk/imx/clk-imx7ulp.c b/drivers/clk/imx/clk-imx7ulp.c
new file mode 100644
index 0000000..3b7507f
--- /dev/null
+++ b/drivers/clk/imx/clk-imx7ulp.c
@@ -0,0 +1,220 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Copyright 2017~2018 NXP
+ *
+ * Author: Dong Aisheng <[email protected]>
+ *
+ */
+
+#include <dt-bindings/clock/imx7ulp-clock.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include "clk.h"
+
+static const char * const pll_pre_sels[] = { "sosc", "firc", };
+static const char * const spll_pfd_sels[] = { "spll_pfd0", "spll_pfd1", "spll_pfd2", "spll_pfd3", };
+static const char * const spll_sels[] = { "spll", "spll_pfd_sel", };
+static const char * const apll_pfd_sels[] = { "apll_pfd0", "apll_pfd1", "apll_pfd2", "apll_pfd3", };
+static const char * const apll_sels[] = { "apll", "apll_pfd_sel", };
+static const char * const scs_sels[] = { "dummy", "sosc", "sirc", "firc", "dummy", "apll_sel", "spll_sel", "upll", };
+static const char * const ddr_sels[] = { "apll_pfd_sel", "upll", };
+static const char * const nic_sels[] = { "firc", "ddr_clk", };
+static const char * const periph_plat_sels[] = { "dummy", "nic1_bus_clk", "nic1_clk", "ddr_clk", "apll_pfd2", "apll_pfd1", "apll_pfd0", "upll", };
+static const char * const periph_bus_sels[] = { "dummy", "sosc_bus_clk", "mpll", "firc_bus_clk", "rosc", "nic1_bus_clk", "nic1_clk", "spll_bus_clk", };
+
+/* used by sosc/sirc/firc/ddr/spll/apll dividers */
+static const struct clk_div_table ulp_div_table[] = {
+ { .val = 1, .div = 1, },
+ { .val = 2, .div = 2, },
+ { .val = 3, .div = 4, },
+ { .val = 4, .div = 8, },
+ { .val = 5, .div = 16, },
+ { .val = 6, .div = 32, },
+ { .val = 7, .div = 64, },
+};
+
+static void __init imx7ulp_clk_scg1_init(struct device_node *np)
+{
+ struct clk_hw_onecell_data *clk_data;
+ struct clk_hw **clks;
+ void __iomem *base;
+
+ clk_data = kzalloc(sizeof(*clk_data) + sizeof(*clk_data->hws) *
+ IMX7ULP_CLK_SCG1_END, GFP_KERNEL);
+ if (!clk_data)
+ return;
+
+ clk_data->num = IMX7ULP_CLK_SCG1_END;
+ clks = clk_data->hws;
+
+ clks[IMX7ULP_CLK_DUMMY] = imx_clk_hw_fixed("dummy", 0);
+
+ clks[IMX7ULP_CLK_ROSC] = imx_obtain_fixed_clk_hw(np, "rosc");
+ clks[IMX7ULP_CLK_SOSC] = imx_obtain_fixed_clk_hw(np, "sosc");
+ clks[IMX7ULP_CLK_SIRC] = imx_obtain_fixed_clk_hw(np, "sirc");
+ clks[IMX7ULP_CLK_FIRC] = imx_obtain_fixed_clk_hw(np, "firc");
+ clks[IMX7ULP_CLK_MIPI_PLL] = imx_obtain_fixed_clk_hw(np, "mpll");
+ clks[IMX7ULP_CLK_UPLL] = imx_obtain_fixed_clk_hw(np, "upll");
+
+ /* SCG1 */
+ base = of_iomap(np, 0);
+ WARN_ON(!base);
+
+ /* NOTE: xPLL config can't be changed when xPLL is enabled */
+ clks[IMX7ULP_CLK_APLL_PRE_SEL] = imx_clk_hw_mux_flags("apll_pre_sel", base + 0x508, 0, 1, pll_pre_sels, ARRAY_SIZE(pll_pre_sels), CLK_SET_PARENT_GATE);
+ clks[IMX7ULP_CLK_SPLL_PRE_SEL] = imx_clk_hw_mux_flags("spll_pre_sel", base + 0x608, 0, 1, pll_pre_sels, ARRAY_SIZE(pll_pre_sels), CLK_SET_PARENT_GATE);
+
+ /* name parent_name reg shift width flags */
+ clks[IMX7ULP_CLK_APLL_PRE_DIV] = imx_clk_hw_divider_flags("apll_pre_div", "apll_pre_sel", base + 0x508, 8, 3, CLK_SET_RATE_GATE);
+ clks[IMX7ULP_CLK_SPLL_PRE_DIV] = imx_clk_hw_divider_flags("spll_pre_div", "spll_pre_sel", base + 0x608, 8, 3, CLK_SET_RATE_GATE);
+
+ /* name parent_name base */
+ clks[IMX7ULP_CLK_APLL] = imx_clk_pllv4("apll", "apll_pre_div", base + 0x500);
+ clks[IMX7ULP_CLK_SPLL] = imx_clk_pllv4("spll", "spll_pre_div", base + 0x600);
+
+ /* APLL PFDs */
+ clks[IMX7ULP_CLK_APLL_PFD0] = imx_clk_pfdv2("apll_pfd0", "apll", base + 0x50c, 0);
+ clks[IMX7ULP_CLK_APLL_PFD1] = imx_clk_pfdv2("apll_pfd1", "apll", base + 0x50c, 1);
+ clks[IMX7ULP_CLK_APLL_PFD2] = imx_clk_pfdv2("apll_pfd2", "apll", base + 0x50c, 2);
+ clks[IMX7ULP_CLK_APLL_PFD3] = imx_clk_pfdv2("apll_pfd3", "apll", base + 0x50c, 3);
+
+ /* SPLL PFDs */
+ clks[IMX7ULP_CLK_SPLL_PFD0] = imx_clk_pfdv2("spll_pfd0", "spll", base + 0x60C, 0);
+ clks[IMX7ULP_CLK_SPLL_PFD1] = imx_clk_pfdv2("spll_pfd1", "spll", base + 0x60C, 1);
+ clks[IMX7ULP_CLK_SPLL_PFD2] = imx_clk_pfdv2("spll_pfd2", "spll", base + 0x60C, 2);
+ clks[IMX7ULP_CLK_SPLL_PFD3] = imx_clk_pfdv2("spll_pfd3", "spll", base + 0x60C, 3);
+
+ /* PLL Mux */
+ clks[IMX7ULP_CLK_APLL_PFD_SEL] = imx_clk_hw_mux_flags("apll_pfd_sel", base + 0x508, 14, 2, apll_pfd_sels, ARRAY_SIZE(apll_pfd_sels), CLK_SET_RATE_PARENT | CLK_SET_PARENT_GATE);
+ clks[IMX7ULP_CLK_SPLL_PFD_SEL] = imx_clk_hw_mux_flags("spll_pfd_sel", base + 0x608, 14, 2, spll_pfd_sels, ARRAY_SIZE(spll_pfd_sels), CLK_SET_RATE_PARENT | CLK_SET_PARENT_GATE);
+ clks[IMX7ULP_CLK_APLL_SEL] = imx_clk_hw_mux_flags("apll_sel", base + 0x508, 1, 1, apll_sels, ARRAY_SIZE(apll_sels), CLK_SET_RATE_PARENT | CLK_SET_PARENT_GATE);
+ clks[IMX7ULP_CLK_SPLL_SEL] = imx_clk_hw_mux_flags("spll_sel", base + 0x608, 1, 1, spll_sels, ARRAY_SIZE(spll_sels), CLK_SET_RATE_PARENT | CLK_SET_PARENT_GATE);
+
+ clks[IMX7ULP_CLK_SPLL_BUS_CLK] = imx_clk_divider_gate("spll_bus_clk", "spll_sel", CLK_SET_RATE_GATE, base + 0x604, 8, 3, 0, ulp_div_table, &imx_ccm_lock);
+
+ /* scs/ddr/nic select different clock source requires that clock to be enabled first */
+ clks[IMX7ULP_CLK_SYS_SEL] = imx_clk_hw_mux2("scs_sel", base + 0x14, 24, 4, scs_sels, ARRAY_SIZE(scs_sels));
+ clks[IMX7ULP_CLK_NIC_SEL] = imx_clk_hw_mux2("nic_sel", base + 0x40, 28, 1, nic_sels, ARRAY_SIZE(nic_sels));
+ clks[IMX7ULP_CLK_DDR_SEL] = imx_clk_hw_mux_flags("ddr_sel", base + 0x30, 24, 1, ddr_sels, ARRAY_SIZE(ddr_sels), CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE);
+
+ clks[IMX7ULP_CLK_CORE_DIV] = imx_clk_hw_divider_flags("divcore", "scs_sel", base + 0x14, 16, 4, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+
+ clks[IMX7ULP_CLK_DDR_DIV] = imx_clk_divider_gate("ddr_clk", "ddr_sel", CLK_SET_RATE_PARENT | CLK_IS_CRITICAL, base + 0x30, 0, 3,
+ 0, ulp_div_table, &imx_ccm_lock);
+
+ clks[IMX7ULP_CLK_NIC0_DIV] = imx_clk_hw_divider_flags("nic0_clk", "nic_sel", base + 0x40, 24, 4, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+ clks[IMX7ULP_CLK_NIC1_DIV] = imx_clk_hw_divider_flags("nic1_clk", "nic0_clk", base + 0x40, 16, 4, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+ clks[IMX7ULP_CLK_NIC1_BUS_DIV] = imx_clk_hw_divider_flags("nic1_bus_clk", "nic1_clk", base + 0x40, 4, 4, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+
+ clks[IMX7ULP_CLK_GPU_DIV] = imx_clk_hw_divider("gpu_clk", "nic0_clk", base + 0x40, 20, 4);
+
+ clks[IMX7ULP_CLK_SOSC_BUS_CLK] = imx_clk_divider_gate("sosc_bus_clk", "sosc", 0, base + 0x104, 8, 3,
+ CLK_DIVIDER_READ_ONLY, ulp_div_table, &imx_ccm_lock);
+ clks[IMX7ULP_CLK_FIRC_BUS_CLK] = imx_clk_divider_gate("firc_bus_clk", "firc", 0, base + 0x304, 8, 3,
+ CLK_DIVIDER_READ_ONLY, ulp_div_table, &imx_ccm_lock);
+
+ imx_check_clk_hws(clks, clk_data->num);
+
+ of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_data);
+}
+CLK_OF_DECLARE(imx7ulp_clk_scg1, "fsl,imx7ulp-scg1", imx7ulp_clk_scg1_init);
+
+static void __init imx7ulp_clk_pcc2_init(struct device_node *np)
+{
+ struct clk_hw_onecell_data *clk_data;
+ struct clk_hw **clks;
+ void __iomem *base;
+
+ clk_data = kzalloc(sizeof(*clk_data) + sizeof(*clk_data->hws) *
+ IMX7ULP_CLK_PCC2_END, GFP_KERNEL);
+ if (!clk_data)
+ return;
+
+ clk_data->num = IMX7ULP_CLK_PCC2_END;
+ clks = clk_data->hws;
+
+ /* PCC2 */
+ base = of_iomap(np, 0);
+ WARN_ON(!base);
+
+ clks[IMX7ULP_CLK_DMA1] = imx_clk_hw_gate("dma1", "nic1_clk", base + 0x20, 30);
+ clks[IMX7ULP_CLK_RGPIO2P1] = imx_clk_hw_gate("rgpio2p1", "nic1_bus_clk", base + 0x3c, 30);
+ clks[IMX7ULP_CLK_DMA_MUX1] = imx_clk_hw_gate("dma_mux1", "nic1_bus_clk", base + 0x84, 30);
+ clks[IMX7ULP_CLK_SNVS] = imx_clk_hw_gate("snvs", "nic1_bus_clk", base + 0x8c, 30);
+ clks[IMX7ULP_CLK_CAAM] = imx_clk_hw_gate("caam", "nic1_clk", base + 0x90, 30);
+ clks[IMX7ULP_CLK_LPTPM4] = imx7ulp_clk_composite("lptpm4", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, false, true, base + 0x94);
+ clks[IMX7ULP_CLK_LPTPM5] = imx7ulp_clk_composite("lptpm5", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, false, true, base + 0x98);
+ clks[IMX7ULP_CLK_LPIT1] = imx7ulp_clk_composite("lpit1", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, false, true, base + 0x9c);
+ clks[IMX7ULP_CLK_LPSPI2] = imx7ulp_clk_composite("lpspi2", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, false, true, base + 0xa4);
+ clks[IMX7ULP_CLK_LPSPI3] = imx7ulp_clk_composite("lpspi3", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, false, true, base + 0xa8);
+ clks[IMX7ULP_CLK_LPI2C4] = imx7ulp_clk_composite("lpi2c4", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, false, true, base + 0xac);
+ clks[IMX7ULP_CLK_LPI2C5] = imx7ulp_clk_composite("lpi2c5", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, false, true, base + 0xb0);
+ clks[IMX7ULP_CLK_LPUART4] = imx7ulp_clk_composite("lpuart4", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, false, true, base + 0xb4);
+ clks[IMX7ULP_CLK_LPUART5] = imx7ulp_clk_composite("lpuart5", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, false, true, base + 0xb8);
+ clks[IMX7ULP_CLK_FLEXIO1] = imx7ulp_clk_composite("flexio1", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, false, true, base + 0xc4);
+ clks[IMX7ULP_CLK_USB0] = imx7ulp_clk_composite("usb0", periph_plat_sels, ARRAY_SIZE(periph_plat_sels), true, true, true, base + 0xcc);
+ clks[IMX7ULP_CLK_USB1] = imx7ulp_clk_composite("usb1", periph_plat_sels, ARRAY_SIZE(periph_plat_sels), true, true, true, base + 0xd0);
+ clks[IMX7ULP_CLK_USB_PHY] = imx_clk_hw_gate("usb_phy", "nic1_bus_clk", base + 0xd4, 30);
+ clks[IMX7ULP_CLK_USDHC0] = imx7ulp_clk_composite("usdhc0", periph_plat_sels, ARRAY_SIZE(periph_plat_sels), true, true, true, base + 0xdc);
+ clks[IMX7ULP_CLK_USDHC1] = imx7ulp_clk_composite("usdhc1", periph_plat_sels, ARRAY_SIZE(periph_plat_sels), true, true, true, base + 0xe0);
+ clks[IMX7ULP_CLK_WDG1] = imx7ulp_clk_composite("wdg1", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, true, true, base + 0xf4);
+ clks[IMX7ULP_CLK_WDG2] = imx7ulp_clk_composite("sdg2", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, true, true, base + 0x10c);
+
+ imx_check_clk_hws(clks, clk_data->num);
+
+ of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_data);
+}
+CLK_OF_DECLARE(imx7ulp_clk_pcc2, "fsl,imx7ulp-pcc2", imx7ulp_clk_pcc2_init);
+
+static void __init imx7ulp_clk_pcc3_init(struct device_node *np)
+{
+ struct clk_hw_onecell_data *clk_data;
+ struct clk_hw **clks;
+ void __iomem *base;
+
+ clk_data = kzalloc(sizeof(*clk_data) + sizeof(*clk_data->hws) *
+ IMX7ULP_CLK_PCC3_END, GFP_KERNEL);
+ if (!clk_data)
+ return;
+
+ clk_data->num = IMX7ULP_CLK_PCC3_END;
+ clks = clk_data->hws;
+
+ /* PCC3 */
+ base = of_iomap(np, 0);
+ WARN_ON(!base);
+
+ clks[IMX7ULP_CLK_LPTPM6] = imx7ulp_clk_composite("lptpm6", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, false, true, base + 0x84);
+ clks[IMX7ULP_CLK_LPTPM7] = imx7ulp_clk_composite("lptpm7", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, false, true, base + 0x88);
+
+ clks[IMX7ULP_CLK_MMDC] = clk_hw_register_gate(NULL, "mmdc", "nic1_clk", CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
+ base + 0xac, 30, 0, &imx_ccm_lock);
+ clks[IMX7ULP_CLK_LPI2C6] = imx7ulp_clk_composite("lpi2c6", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, false, true, base + 0x90);
+ clks[IMX7ULP_CLK_LPI2C7] = imx7ulp_clk_composite("lpi2c7", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, false, true, base + 0x94);
+ clks[IMX7ULP_CLK_LPUART6] = imx7ulp_clk_composite("lpuart6", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, false, true, base + 0x98);
+ clks[IMX7ULP_CLK_LPUART7] = imx7ulp_clk_composite("lpuart7", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, false, true, base + 0x9c);
+ clks[IMX7ULP_CLK_DSI] = imx7ulp_clk_composite("dsi", periph_bus_sels, ARRAY_SIZE(periph_bus_sels), true, true, true, base + 0xa4);
+ clks[IMX7ULP_CLK_LCDIF] = imx7ulp_clk_composite("lcdif", periph_plat_sels, ARRAY_SIZE(periph_plat_sels), true, true, true, base + 0xa8);
+
+ clks[IMX7ULP_CLK_VIU] = imx_clk_hw_gate("viu", "nic1_clk", base + 0xa0, 30);
+ clks[IMX7ULP_CLK_PCTLC] = imx_clk_hw_gate("pctlc", "nic1_bus_clk", base + 0xb8, 30);
+ clks[IMX7ULP_CLK_PCTLD] = imx_clk_hw_gate("pctld", "nic1_bus_clk", base + 0xbc, 30);
+ clks[IMX7ULP_CLK_PCTLE] = imx_clk_hw_gate("pctle", "nic1_bus_clk", base + 0xc0, 30);
+ clks[IMX7ULP_CLK_PCTLF] = imx_clk_hw_gate("pctlf", "nic1_bus_clk", base + 0xc4, 30);
+
+ clks[IMX7ULP_CLK_GPU3D] = imx7ulp_clk_composite("gpu3d", periph_plat_sels, ARRAY_SIZE(periph_plat_sels), true, false, true, base + 0x140);
+ clks[IMX7ULP_CLK_GPU2D] = imx7ulp_clk_composite("gpu2d", periph_plat_sels, ARRAY_SIZE(periph_plat_sels), true, false, true, base + 0x144);
+
+ imx_check_clk_hws(clks, clk_data->num);
+
+ of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_data);
+}
+CLK_OF_DECLARE(imx7ulp_clk_pcc3, "fsl,imx7ulp-pcc3", imx7ulp_clk_pcc3_init);
--
2.7.4
Adding CLK_FRAC_DIVIDER_ZERO_BASED flag to indicate the numerator and
denominator value in register are start from 0.
This can be used to support frac dividers like below:
Divider output clock = Divider input clock x [(frac +1) / (div +1)]
where frac/div in register is:
000b - Divide by 1.
001b - Divide by 2.
010b - Divide by 3.
Cc: Stephen Boyd <[email protected]>
Cc: Michael Turquette <[email protected]>
Signed-off-by: Dong Aisheng <[email protected]>
---
ChangeLog:
v3->v4:
* no changes
v2->v3:
* no changes
v1->v2:
* improve comments suggested by Stephen
---
drivers/clk/clk-fractional-divider.c | 10 ++++++++++
include/linux/clk-provider.h | 8 ++++++++
2 files changed, 18 insertions(+)
diff --git a/drivers/clk/clk-fractional-divider.c b/drivers/clk/clk-fractional-divider.c
index fdf625f..7ccde6b 100644
--- a/drivers/clk/clk-fractional-divider.c
+++ b/drivers/clk/clk-fractional-divider.c
@@ -40,6 +40,11 @@ static unsigned long clk_fd_recalc_rate(struct clk_hw *hw,
m = (val & fd->mmask) >> fd->mshift;
n = (val & fd->nmask) >> fd->nshift;
+ if (fd->flags & CLK_FRAC_DIVIDER_ZERO_BASED) {
+ m++;
+ n++;
+ }
+
if (!n || !m)
return parent_rate;
@@ -103,6 +108,11 @@ static int clk_fd_set_rate(struct clk_hw *hw, unsigned long rate,
GENMASK(fd->mwidth - 1, 0), GENMASK(fd->nwidth - 1, 0),
&m, &n);
+ if (fd->flags & CLK_FRAC_DIVIDER_ZERO_BASED) {
+ m--;
+ n--;
+ }
+
if (fd->lock)
spin_lock_irqsave(fd->lock, flags);
else
diff --git a/include/linux/clk-provider.h b/include/linux/clk-provider.h
index 08b1aa7..bee6453 100644
--- a/include/linux/clk-provider.h
+++ b/include/linux/clk-provider.h
@@ -594,6 +594,12 @@ void clk_hw_unregister_fixed_factor(struct clk_hw *hw);
* @lock: register lock
*
* Clock with adjustable fractional divider affecting its output frequency.
+ *
+ * Flags:
+ * CLK_FRAC_DIVIDER_ZERO_BASED - by default the numerator and denominator
+ * is the value read from the register. If CLK_FRAC_DIVIDER_ZERO_BASED
+ * is set then the numerator and denominator are both the value read
+ * plus one.
*/
struct clk_fractional_divider {
struct clk_hw hw;
@@ -613,6 +619,8 @@ struct clk_fractional_divider {
#define to_clk_fd(_hw) container_of(_hw, struct clk_fractional_divider, hw)
+#define CLK_FRAC_DIVIDER_ZERO_BASED BIT(0)
+
extern const struct clk_ops clk_fractional_divider_ops;
struct clk *clk_register_fractional_divider(struct device *dev,
const char *name, const char *parent_name, unsigned long flags,
--
2.7.4
As the commit 2893c379461a ("clk: make strings in parent name arrays
const"), let's make the parent strings const, otherwise we may meet
the following warning when compiling:
drivers/clk/imx/clk-imx7ulp.c: In function 'imx7ulp_clocks_init':
drivers/clk/imx/clk-imx7ulp.c:73:35: warning: passing argument 5 of
'imx_clk_mux_flags' discards 'const' qualifier from pointer target type
clks[IMX7ULP_CLK_APLL_PRE_SEL] = imx_clk_mux_flags("apll_pre_sel", base + 0x508, 0,
1, pll_pre_sels, ARRAY_SIZE(pll_pre_sels), CLK_SET_PARENT_GATE);
^
In file included from drivers/clk/imx/clk-imx7ulp.c:23:0:
drivers/clk/imx/clk.h:200:27: note: expected 'const char **' but argument is
of type 'const char * const*'
...
Cc: Stephen Boyd <[email protected]>
Cc: Michael Turquette <[email protected]>
Cc: Shawn Guo <[email protected]>
Signed-off-by: Dong Aisheng <[email protected]>
---
ChangeLog:
v1->v4: no changes
---
drivers/clk/imx/clk-busy.c | 2 +-
drivers/clk/imx/clk-fixup-mux.c | 2 +-
drivers/clk/imx/clk.h | 18 +++++++++++-------
3 files changed, 13 insertions(+), 9 deletions(-)
diff --git a/drivers/clk/imx/clk-busy.c b/drivers/clk/imx/clk-busy.c
index 9903652..e695622 100644
--- a/drivers/clk/imx/clk-busy.c
+++ b/drivers/clk/imx/clk-busy.c
@@ -154,7 +154,7 @@ static const struct clk_ops clk_busy_mux_ops = {
struct clk *imx_clk_busy_mux(const char *name, void __iomem *reg, u8 shift,
u8 width, void __iomem *busy_reg, u8 busy_shift,
- const char **parent_names, int num_parents)
+ const char * const *parent_names, int num_parents)
{
struct clk_busy_mux *busy;
struct clk *clk;
diff --git a/drivers/clk/imx/clk-fixup-mux.c b/drivers/clk/imx/clk-fixup-mux.c
index c9b327e..44817c1 100644
--- a/drivers/clk/imx/clk-fixup-mux.c
+++ b/drivers/clk/imx/clk-fixup-mux.c
@@ -70,7 +70,7 @@ static const struct clk_ops clk_fixup_mux_ops = {
};
struct clk *imx_clk_fixup_mux(const char *name, void __iomem *reg,
- u8 shift, u8 width, const char **parents,
+ u8 shift, u8 width, const char * const *parents,
int num_parents, void (*fixup)(u32 *val))
{
struct clk_fixup_mux *fixup_mux;
diff --git a/drivers/clk/imx/clk.h b/drivers/clk/imx/clk.h
index 2e3bcfa..3886979 100644
--- a/drivers/clk/imx/clk.h
+++ b/drivers/clk/imx/clk.h
@@ -69,7 +69,7 @@ struct clk *imx_clk_busy_divider(const char *name, const char *parent_name,
struct clk *imx_clk_busy_mux(const char *name, void __iomem *reg, u8 shift,
u8 width, void __iomem *busy_reg, u8 busy_shift,
- const char **parent_names, int num_parents);
+ const char * const *parent_names, int num_parents);
struct clk_hw *imx7ulp_clk_composite(const char *name,
const char * const *parent_names,
@@ -82,7 +82,7 @@ struct clk *imx_clk_fixup_divider(const char *name, const char *parent,
void (*fixup)(u32 *val));
struct clk *imx_clk_fixup_mux(const char *name, void __iomem *reg,
- u8 shift, u8 width, const char **parents,
+ u8 shift, u8 width, const char * const *parents,
int num_parents, void (*fixup)(u32 *val));
static inline struct clk *imx_clk_fixed(const char *name, int rate)
@@ -91,7 +91,8 @@ static inline struct clk *imx_clk_fixed(const char *name, int rate)
}
static inline struct clk *imx_clk_mux_ldb(const char *name, void __iomem *reg,
- u8 shift, u8 width, const char **parents, int num_parents)
+ u8 shift, u8 width, const char * const *parents,
+ int num_parents)
{
return clk_register_mux(NULL, name, parents, num_parents,
CLK_SET_RATE_NO_REPARENT | CLK_SET_RATE_PARENT, reg,
@@ -204,7 +205,8 @@ static inline struct clk *imx_clk_gate4(const char *name, const char *parent,
}
static inline struct clk *imx_clk_mux(const char *name, void __iomem *reg,
- u8 shift, u8 width, const char **parents, int num_parents)
+ u8 shift, u8 width, const char * const *parents,
+ int num_parents)
{
return clk_register_mux(NULL, name, parents, num_parents,
CLK_SET_RATE_NO_REPARENT, reg, shift,
@@ -212,7 +214,8 @@ static inline struct clk *imx_clk_mux(const char *name, void __iomem *reg,
}
static inline struct clk *imx_clk_mux2(const char *name, void __iomem *reg,
- u8 shift, u8 width, const char **parents, int num_parents)
+ u8 shift, u8 width, const char * const *parents,
+ int num_parents)
{
return clk_register_mux(NULL, name, parents, num_parents,
CLK_SET_RATE_NO_REPARENT | CLK_OPS_PARENT_ENABLE,
@@ -220,8 +223,9 @@ static inline struct clk *imx_clk_mux2(const char *name, void __iomem *reg,
}
static inline struct clk *imx_clk_mux_flags(const char *name,
- void __iomem *reg, u8 shift, u8 width, const char **parents,
- int num_parents, unsigned long flags)
+ void __iomem *reg, u8 shift, u8 width,
+ const char * const *parents, int num_parents,
+ unsigned long flags)
{
return clk_register_mux(NULL, name, parents, num_parents,
flags | CLK_SET_RATE_NO_REPARENT, reg, shift, width, 0,
--
2.7.4
pllv4 is designed for System Clock Generation (SCG) module observed
in IMX ULP SoC series. e.g. i.MX7ULP.
The SCG modules generates clock used to derive processor, system,
peripheral bus and external memory interface clocks while this patch
intends to support the PLL part.
Cc: Stephen Boyd <[email protected]>
Cc: Michael Turquette <[email protected]>
Cc: Shawn Guo <[email protected]>
Cc: Anson Huang <[email protected]>
Cc: Bai Ping <[email protected]>
Signed-off-by: Dong Aisheng <[email protected]>
---
ChangeLog:
v3->v4:
* no changes
v2->v3:
* no changes
v1->v2:
* remove clk_pllv4_is_enabled() check in set_rate, instead it will
be handled by core later.
* use readl_poll_timeout
* use clk_hw_register instead of clk_register
* other minor changes
---
drivers/clk/imx/Makefile | 1 +
drivers/clk/imx/clk-pllv4.c | 182 ++++++++++++++++++++++++++++++++++++++++++++
drivers/clk/imx/clk.h | 3 +
3 files changed, 186 insertions(+)
create mode 100644 drivers/clk/imx/clk-pllv4.c
diff --git a/drivers/clk/imx/Makefile b/drivers/clk/imx/Makefile
index 077e732..4cac28b 100644
--- a/drivers/clk/imx/Makefile
+++ b/drivers/clk/imx/Makefile
@@ -12,6 +12,7 @@ obj-y += \
clk-pllv1.o \
clk-pllv2.o \
clk-pllv3.o \
+ clk-pllv4.o \
clk-pfd.o
obj-$(CONFIG_SOC_IMX1) += clk-imx1.o
diff --git a/drivers/clk/imx/clk-pllv4.c b/drivers/clk/imx/clk-pllv4.c
new file mode 100644
index 0000000..67c64c7
--- /dev/null
+++ b/drivers/clk/imx/clk-pllv4.c
@@ -0,0 +1,182 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Copyright 2017~2018 NXP
+ *
+ * Author: Dong Aisheng <[email protected]>
+ *
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/err.h>
+#include <linux/iopoll.h>
+#include <linux/slab.h>
+
+/* PLL Control Status Register (xPLLCSR) */
+#define PLL_CSR_OFFSET 0x0
+#define PLL_VLD BIT(24)
+#define PLL_EN BIT(0)
+
+/* PLL Configuration Register (xPLLCFG) */
+#define PLL_CFG_OFFSET 0x08
+#define BP_PLL_MULT 16
+#define BM_PLL_MULT (0x7f << 16)
+
+/* PLL Numerator Register (xPLLNUM) */
+#define PLL_NUM_OFFSET 0x10
+
+/* PLL Denominator Register (xPLLDENOM) */
+#define PLL_DENOM_OFFSET 0x14
+
+struct clk_pllv4 {
+ struct clk_hw hw;
+ void __iomem *base;
+};
+
+/* Valid PLL MULT Table */
+static const int pllv4_mult_table[] = {33, 27, 22, 20, 17, 16};
+
+#define to_clk_pllv4(__hw) container_of(__hw, struct clk_pllv4, hw)
+
+#define LOCK_TIMEOUT_US USEC_PER_MSEC
+
+static inline int clk_pllv4_wait_lock(struct clk_pllv4 *pll)
+{
+ u32 csr;
+
+ return readl_poll_timeout(pll->base + PLL_CSR_OFFSET,
+ csr, csr & PLL_VLD, 0, LOCK_TIMEOUT_US);
+}
+
+static int clk_pllv4_is_enabled(struct clk_hw *hw)
+{
+ struct clk_pllv4 *pll = to_clk_pllv4(hw);
+
+ if (readl_relaxed(pll->base) & PLL_EN)
+ return 1;
+
+ return 0;
+}
+
+static unsigned long clk_pllv4_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct clk_pllv4 *pll = to_clk_pllv4(hw);
+ u32 div;
+
+ div = readl_relaxed(pll->base + PLL_CFG_OFFSET);
+ div &= BM_PLL_MULT;
+ div >>= BP_PLL_MULT;
+
+ return parent_rate * div;
+}
+
+static long clk_pllv4_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *prate)
+{
+ unsigned long parent_rate = *prate;
+ unsigned long round_rate, i;
+
+ for (i = 0; i < ARRAY_SIZE(pllv4_mult_table); i++) {
+ round_rate = parent_rate * pllv4_mult_table[i];
+ if (rate >= round_rate)
+ return round_rate;
+ }
+
+ return round_rate;
+}
+
+static bool clk_pllv4_is_valid_mult(unsigned int mult)
+{
+ int i;
+
+ /* check if mult is in valid MULT table */
+ for (i = 0; i < ARRAY_SIZE(pllv4_mult_table); i++) {
+ if (pllv4_mult_table[i] == mult)
+ return true;
+ }
+
+ return false;
+}
+
+static int clk_pllv4_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct clk_pllv4 *pll = to_clk_pllv4(hw);
+ u32 val, mult;
+
+ mult = rate / parent_rate;
+
+ if (!clk_pllv4_is_valid_mult(mult))
+ return -EINVAL;
+
+ val = readl_relaxed(pll->base + PLL_CFG_OFFSET);
+ val &= ~BM_PLL_MULT;
+ val |= mult << BP_PLL_MULT;
+ writel_relaxed(val, pll->base + PLL_CFG_OFFSET);
+
+ return 0;
+}
+
+static int clk_pllv4_enable(struct clk_hw *hw)
+{
+ u32 val;
+ struct clk_pllv4 *pll = to_clk_pllv4(hw);
+
+ val = readl_relaxed(pll->base);
+ val |= PLL_EN;
+ writel_relaxed(val, pll->base);
+
+ return clk_pllv4_wait_lock(pll);
+}
+
+static void clk_pllv4_disable(struct clk_hw *hw)
+{
+ u32 val;
+ struct clk_pllv4 *pll = to_clk_pllv4(hw);
+
+ val = readl_relaxed(pll->base);
+ val &= ~PLL_EN;
+ writel_relaxed(val, pll->base);
+}
+
+static const struct clk_ops clk_pllv4_ops = {
+ .recalc_rate = clk_pllv4_recalc_rate,
+ .round_rate = clk_pllv4_round_rate,
+ .set_rate = clk_pllv4_set_rate,
+ .enable = clk_pllv4_enable,
+ .disable = clk_pllv4_disable,
+ .is_enabled = clk_pllv4_is_enabled,
+};
+
+struct clk_hw *imx_clk_pllv4(const char *name, const char *parent_name,
+ void __iomem *base)
+{
+ struct clk_pllv4 *pll;
+ struct clk_hw *hw;
+ struct clk_init_data init;
+ int ret;
+
+ pll = kzalloc(sizeof(*pll), GFP_KERNEL);
+ if (!pll)
+ return ERR_PTR(-ENOMEM);
+
+ pll->base = base;
+
+ init.name = name;
+ init.ops = &clk_pllv4_ops;
+ init.parent_names = &parent_name;
+ init.num_parents = 1;
+ init.flags = CLK_SET_RATE_GATE;
+
+ pll->hw.init = &init;
+
+ hw = &pll->hw;
+ ret = clk_hw_register(NULL, hw);
+ if (ret) {
+ kfree(pll);
+ hw = ERR_PTR(ret);
+ }
+
+ return hw;
+}
diff --git a/drivers/clk/imx/clk.h b/drivers/clk/imx/clk.h
index 8e65282..1e11eb7 100644
--- a/drivers/clk/imx/clk.h
+++ b/drivers/clk/imx/clk.h
@@ -42,6 +42,9 @@ enum imx_pllv3_type {
struct clk *imx_clk_pllv3(enum imx_pllv3_type type, const char *name,
const char *parent_name, void __iomem *base, u32 div_mask);
+struct clk_hw *imx_clk_pllv4(const char *name, const char *parent_name,
+ void __iomem *base);
+
struct clk *clk_register_gate2(struct device *dev, const char *name,
const char *parent_name, unsigned long flags,
void __iomem *reg, u8 bit_idx, u8 cgr_val,
--
2.7.4
Clock providers are recommended to use the new struct clk_hw based API,
so implement IMX clk_hw based provider helpers functions to the new
approach.
Signed-off-by: Dong Aisheng <[email protected]>
---
ChangeLog:
v2->v4:
* no changes
v1->v2: new patches
---
drivers/clk/imx/clk.c | 22 ++++++++++++++++++
drivers/clk/imx/clk.h | 62 +++++++++++++++++++++++++++++++++++++++++++++++++++
2 files changed, 84 insertions(+)
diff --git a/drivers/clk/imx/clk.c b/drivers/clk/imx/clk.c
index 9074e69..1efed86 100644
--- a/drivers/clk/imx/clk.c
+++ b/drivers/clk/imx/clk.c
@@ -18,6 +18,16 @@ void __init imx_check_clocks(struct clk *clks[], unsigned int count)
i, PTR_ERR(clks[i]));
}
+void imx_check_clk_hws(struct clk_hw *clks[], unsigned int count)
+{
+ unsigned int i;
+
+ for (i = 0; i < count; i++)
+ if (IS_ERR(clks[i]))
+ pr_err("i.MX clk %u: register failed with %ld\n",
+ i, PTR_ERR(clks[i]));
+}
+
static struct clk * __init imx_obtain_fixed_clock_from_dt(const char *name)
{
struct of_phandle_args phandle;
@@ -49,6 +59,18 @@ struct clk * __init imx_obtain_fixed_clock(
return clk;
}
+struct clk_hw * __init imx_obtain_fixed_clk_hw(struct device_node *np,
+ const char *name)
+{
+ struct clk *clk;
+
+ clk = of_clk_get_by_name(np, name);
+ if (IS_ERR(clk))
+ return ERR_PTR(-ENOENT);
+
+ return __clk_get_hw(clk);
+}
+
/*
* This fixups the register CCM_CSCMR1 write value.
* The write/read/divider values of the aclk_podf field
diff --git a/drivers/clk/imx/clk.h b/drivers/clk/imx/clk.h
index 3886979..cf0596d 100644
--- a/drivers/clk/imx/clk.h
+++ b/drivers/clk/imx/clk.h
@@ -8,6 +8,7 @@
extern spinlock_t imx_ccm_lock;
void imx_check_clocks(struct clk *clks[], unsigned int count);
+void imx_check_clk_hws(struct clk_hw *clks[], unsigned int count);
void imx_register_uart_clocks(struct clk ** const clks[]);
extern void imx_cscmr1_fixup(u32 *val);
@@ -54,6 +55,9 @@ struct clk *clk_register_gate2(struct device *dev, const char *name,
struct clk * imx_obtain_fixed_clock(
const char *name, unsigned long rate);
+struct clk_hw *imx_obtain_fixed_clk_hw(struct device_node *np,
+ const char *name);
+
struct clk *imx_clk_gate_exclusive(const char *name, const char *parent,
void __iomem *reg, u8 shift, u32 exclusive_mask);
@@ -90,6 +94,16 @@ static inline struct clk *imx_clk_fixed(const char *name, int rate)
return clk_register_fixed_rate(NULL, name, NULL, 0, rate);
}
+static inline struct clk_hw *imx_clk_hw_fixed(const char *name, int rate)
+{
+ return clk_hw_register_fixed_rate(NULL, name, NULL, 0, rate);
+}
+
+static inline struct clk_hw *imx_get_clk_hw_fixed(const char *name, int rate)
+{
+ return clk_hw_register_fixed_rate(NULL, name, NULL, 0, rate);
+}
+
static inline struct clk *imx_clk_mux_ldb(const char *name, void __iomem *reg,
u8 shift, u8 width, const char * const *parents,
int num_parents)
@@ -113,6 +127,15 @@ static inline struct clk *imx_clk_divider(const char *name, const char *parent,
reg, shift, width, 0, &imx_ccm_lock);
}
+static inline struct clk_hw *imx_clk_hw_divider(const char *name,
+ const char *parent,
+ void __iomem *reg, u8 shift,
+ u8 width)
+{
+ return clk_hw_register_divider(NULL, name, parent, CLK_SET_RATE_PARENT,
+ reg, shift, width, 0, &imx_ccm_lock);
+}
+
static inline struct clk *imx_clk_divider_flags(const char *name,
const char *parent, void __iomem *reg, u8 shift, u8 width,
unsigned long flags)
@@ -121,6 +144,15 @@ static inline struct clk *imx_clk_divider_flags(const char *name,
reg, shift, width, 0, &imx_ccm_lock);
}
+static inline struct clk_hw *imx_clk_hw_divider_flags(const char *name,
+ const char *parent,
+ void __iomem *reg, u8 shift,
+ u8 width, unsigned long flags)
+{
+ return clk_hw_register_divider(NULL, name, parent, flags,
+ reg, shift, width, 0, &imx_ccm_lock);
+}
+
static inline struct clk *imx_clk_divider2(const char *name, const char *parent,
void __iomem *reg, u8 shift, u8 width)
{
@@ -143,6 +175,13 @@ static inline struct clk *imx_clk_gate_flags(const char *name, const char *paren
shift, 0, &imx_ccm_lock);
}
+static inline struct clk_hw *imx_clk_hw_gate(const char *name, const char *parent,
+ void __iomem *reg, u8 shift)
+{
+ return clk_hw_register_gate(NULL, name, parent, CLK_SET_RATE_PARENT, reg,
+ shift, 0, &imx_ccm_lock);
+}
+
static inline struct clk *imx_clk_gate_dis(const char *name, const char *parent,
void __iomem *reg, u8 shift)
{
@@ -222,6 +261,17 @@ static inline struct clk *imx_clk_mux2(const char *name, void __iomem *reg,
reg, shift, width, 0, &imx_ccm_lock);
}
+static inline struct clk_hw *imx_clk_hw_mux2(const char *name, void __iomem *reg,
+ u8 shift, u8 width,
+ const char * const *parents,
+ int num_parents)
+{
+ return clk_hw_register_mux(NULL, name, parents, num_parents,
+ CLK_SET_RATE_NO_REPARENT |
+ CLK_OPS_PARENT_ENABLE,
+ reg, shift, width, 0, &imx_ccm_lock);
+}
+
static inline struct clk *imx_clk_mux_flags(const char *name,
void __iomem *reg, u8 shift, u8 width,
const char * const *parents, int num_parents,
@@ -232,6 +282,18 @@ static inline struct clk *imx_clk_mux_flags(const char *name,
&imx_ccm_lock);
}
+static inline struct clk_hw *imx_clk_hw_mux_flags(const char *name,
+ void __iomem *reg, u8 shift,
+ u8 width,
+ const char * const *parents,
+ int num_parents,
+ unsigned long flags)
+{
+ return clk_hw_register_mux(NULL, name, parents, num_parents,
+ flags | CLK_SET_RATE_NO_REPARENT,
+ reg, shift, width, 0, &imx_ccm_lock);
+}
+
struct clk *imx_clk_cpu(const char *name, const char *parent_name,
struct clk *div, struct clk *mux, struct clk *pll,
struct clk *step);
--
2.7.4
Quoting A.s. Dong (2018-11-14 05:01:31)
> This patch series intends to add imx7ulp clk support.
>
> i.MX7ULP Clock functions are under joint control of the System
> Clock Generation (SCG) modules, Peripheral Clock Control (PCC)
> modules, and Core Mode Controller (CMC)1 blocks
>
> The clocking scheme provides clear separation between M4 domain
> and A7 domain. Except for a few clock sources shared between two
> domains, such as the System Oscillator clock, the Slow IRC (SIRC),
> and and the Fast IRC clock (FIRCLK), clock sources and clock
> management are separated and contained within each domain.
>
> M4 clock management consists of SCG0, PCC0, PCC1, and CMC0 modules.
> A7 clock management consists of SCG1, PCC2, PCC3, and CMC1 modules.
>
> Note: this series only adds A7 clock domain support as M4 clock
> domain will be handled by M4 seperately.
>
I got:
drivers/clk/imx/clk-pllv4.c:152:15: warning: symbol 'imx_clk_pllv4' was not declared. Should it be static?
drivers/clk/imx/clk-pfdv2.c:166:15: warning: symbol 'imx_clk_pfdv2' was not declared. Should it be static?
drivers/clk/imx/clk-divider-gate.c:174:15: warning: symbol 'imx_clk_divider_gate' was not declared. Should it be static?
drivers/clk/imx/clk-composite-7ulp.c:22:15: warning: symbol 'imx7ulp_clk_composite' was not declared. Should it be static?
which I can fix easily by throwing in clk.h into each file.
Quoting A.s. Dong (2018-11-14 05:01:35)
> For dividers with zero indicating clock is disabled, instead of giving a
> warning each time like "clkx: Zero divisor and CLK_DIVIDER_ALLOW_ZERO not
> set" in exist code, we'd like to introduce enable/disable function for it.
> e.g.
> 000b - Clock disabled
> 001b - Divide by 1
> 010b - Divide by 2
> ...
>
> Set rate when the clk is disabled will cache the rate request and only
> when the clk is enabled will the driver actually program the hardware to
> have the requested divider value. Similarly, when the clk is disabled we'll
> write a 0 there, but when the clk is enabled we'll restore whatever rate
> (divider) was chosen last.
>
> It does mean that recalc rate will be sort of odd, because when the clk is
> off it will return 0, and when the clk is on it will return the right rate.
> So to make things work, we'll need to return the cached rate in recalc rate
> when the clk is off and read the hardware when the clk is on.
>
> NOTE for the default off divider, the recalc rate will still return 0 as
> there's still no proper preset rate. Enable such divider will give user
> a reminder error message.
>
> Cc: Stephen Boyd <[email protected]>
> Cc: Michael Turquette <[email protected]>
> Cc: Shawn Guo <[email protected]>
> Signed-off-by: Dong Aisheng <[email protected]>
>
> ---
Applied to clk-next
Quoting A.s. Dong (2018-11-14 05:01:39)
> Adding CLK_FRAC_DIVIDER_ZERO_BASED flag to indicate the numerator and
> denominator value in register are start from 0.
>
> This can be used to support frac dividers like below:
> Divider output clock = Divider input clock x [(frac +1) / (div +1)]
> where frac/div in register is:
> 000b - Divide by 1.
> 001b - Divide by 2.
> 010b - Divide by 3.
>
> Cc: Stephen Boyd <[email protected]>
> Cc: Michael Turquette <[email protected]>
> Signed-off-by: Dong Aisheng <[email protected]>
>
> ---
Applied to clk-next
Quoting A.s. Dong (2018-11-14 05:01:43)
> pllv4 is designed for System Clock Generation (SCG) module observed
> in IMX ULP SoC series. e.g. i.MX7ULP.
>
> The SCG modules generates clock used to derive processor, system,
> peripheral bus and external memory interface clocks while this patch
> intends to support the PLL part.
>
> Cc: Stephen Boyd <[email protected]>
> Cc: Michael Turquette <[email protected]>
> Cc: Shawn Guo <[email protected]>
> Cc: Anson Huang <[email protected]>
> Cc: Bai Ping <[email protected]>
> Signed-off-by: Dong Aisheng <[email protected]>
>
> ---
Applied to clk-next
Quoting A.s. Dong (2018-11-14 05:01:47)
> The pfdv2 is designed for PLL Fractional Divide (PFD) observed in System
> Clock Generation (SCG) module in IMX ULP SoC series. e.g. i.MX7ULP.
>
> NOTE pfdv2 can only be operated when clk is gated.
>
> Cc: Stephen Boyd <[email protected]>
> Cc: Michael Turquette <[email protected]>
> Cc: Shawn Guo <[email protected]>
> Cc: Anson Huang <[email protected]>
> Cc: Bai Ping <[email protected]>
> Signed-off-by: Dong Aisheng <[email protected]>
>
> ---
Applied to clk-next
Quoting A.s. Dong (2018-11-14 05:01:51)
> The imx composite clk is designed for Peripheral Clock Control (PCC)
> module observed in IMX ULP SoC series.
>
> NOTE pcc can only be operated when clk is gated.
>
> Cc: Stephen Boyd <[email protected]>
> Cc: Michael Turquette <[email protected]>
> Cc: Shawn Guo <[email protected]>
> Cc: Anson Huang <[email protected]>
> Cc: Bai Ping <[email protected]>
> Signed-off-by: Dong Aisheng <[email protected]>
>
> ---
Applied to clk-next
Quoting A.s. Dong (2018-11-14 05:01:56)
> i.MX7ULP Clock functions are under joint control of the System
> Clock Generation (SCG) modules, Peripheral Clock Control (PCC)
> modules, and Core Mode Controller (CMC)1 blocks
>
> Note IMX7ULP has two clock domains: M4 and A7. This binding doc
> is only for A7 clock domain.
>
> Cc: Rob Herring <[email protected]>
> Cc: Mark Rutland <[email protected]>
> Cc: Stephen Boyd <[email protected]>
> Cc: Michael Turquette <[email protected]>
> Cc: Shawn Guo <[email protected]>
> Cc: Anson Huang <[email protected]>
> Cc: Bai Ping <[email protected]>
> Signed-off-by: Dong Aisheng <[email protected]>
>
> ---
Applied to clk-next
Quoting A.s. Dong (2018-11-14 05:02:00)
> As the commit 2893c379461a ("clk: make strings in parent name arrays
> const"), let's make the parent strings const, otherwise we may meet
> the following warning when compiling:
>
> drivers/clk/imx/clk-imx7ulp.c: In function 'imx7ulp_clocks_init':
> drivers/clk/imx/clk-imx7ulp.c:73:35: warning: passing argument 5 of
> 'imx_clk_mux_flags' discards 'const' qualifier from pointer target type
>
> clks[IMX7ULP_CLK_APLL_PRE_SEL] = imx_clk_mux_flags("apll_pre_sel", base + 0x508, 0,
> 1, pll_pre_sels, ARRAY_SIZE(pll_pre_sels), CLK_SET_PARENT_GATE);
> ^
> In file included from drivers/clk/imx/clk-imx7ulp.c:23:0:
> drivers/clk/imx/clk.h:200:27: note: expected 'const char **' but argument is
> of type 'const char * const*'
> ...
>
> Cc: Stephen Boyd <[email protected]>
> Cc: Michael Turquette <[email protected]>
> Cc: Shawn Guo <[email protected]>
> Signed-off-by: Dong Aisheng <[email protected]>
>
> ---
Applied to clk-next
Quoting A.s. Dong (2018-11-14 05:02:04)
> Clock providers are recommended to use the new struct clk_hw based API,
> so implement IMX clk_hw based provider helpers functions to the new
> approach.
>
> Signed-off-by: Dong Aisheng <[email protected]>
>
> ---
Applied to clk-next
Quoting A.s. Dong (2018-11-14 05:02:08)
> i.MX7ULP Clock functions are under joint control of the System
> Clock Generation (SCG) modules, Peripheral Clock Control (PCC)
> modules, and Core Mode Controller (CMC)1 blocks
>
> The clocking scheme provides clear separation between M4 domain
> and A7 domain. Except for a few clock sources shared between two
> domains, such as the System Oscillator clock, the Slow IRC (SIRC),
> and and the Fast IRC clock (FIRCLK), clock sources and clock
> management are separated and contained within each domain.
>
> M4 clock management consists of SCG0, PCC0, PCC1, and CMC0 modules.
> A7 clock management consists of SCG1, PCC2, PCC3, and CMC1 modules.
>
> This driver only adds clock support in A7 domain.
>
> Note that most clocks required to be operated when gated, e.g. pll,
> pfd, pcc. And more special cases that scs/ddr/nic mux selecting
> different clock source requires that clock to be enabled first,
> then we need set CLK_OPS_PARENT_ENABLE flag for them properly.
>
> Cc: Stephen Boyd <[email protected]>
> Cc: Michael Turquette <[email protected]>
> Cc: Shawn Guo <[email protected]>
> Cc: Anson Huang <[email protected]>
> Cc: Bai Ping <[email protected]>
> Signed-off-by: Dong Aisheng <[email protected]>
>
> ---
Applied to clk-next
> -----Original Message-----
> From: Stephen Boyd [mailto:[email protected]]
> Sent: Tuesday, December 4, 2018 3:32 AM
> To: Aisheng DONG <[email protected]>; [email protected]
> Cc: [email protected]; [email protected];
> [email protected]; [email protected]; Anson Huang
> <[email protected]>; Jacky Bai <[email protected]>; dl-linux-imx
> <[email protected]>; Aisheng DONG <[email protected]>
> Subject: Re: [PATCH V6 0/9] clk: add imx7ulp clk support
>
> Quoting A.s. Dong (2018-11-14 05:01:31)
> > This patch series intends to add imx7ulp clk support.
> >
> > i.MX7ULP Clock functions are under joint control of the System Clock
> > Generation (SCG) modules, Peripheral Clock Control (PCC) modules, and
> > Core Mode Controller (CMC)1 blocks
> >
> > The clocking scheme provides clear separation between M4 domain and A7
> > domain. Except for a few clock sources shared between two domains,
> > such as the System Oscillator clock, the Slow IRC (SIRC), and and the
> > Fast IRC clock (FIRCLK), clock sources and clock management are
> > separated and contained within each domain.
> >
> > M4 clock management consists of SCG0, PCC0, PCC1, and CMC0 modules.
> > A7 clock management consists of SCG1, PCC2, PCC3, and CMC1 modules.
> >
> > Note: this series only adds A7 clock domain support as M4 clock domain
> > will be handled by M4 seperately.
> >
>
> I got:
>
> drivers/clk/imx/clk-pllv4.c:152:15: warning: symbol 'imx_clk_pllv4' was not
> declared. Should it be static?
> drivers/clk/imx/clk-pfdv2.c:166:15: warning: symbol 'imx_clk_pfdv2' was not
> declared. Should it be static?
> drivers/clk/imx/clk-divider-gate.c:174:15: warning: symbol
> 'imx_clk_divider_gate' was not declared. Should it be static?
> drivers/clk/imx/clk-composite-7ulp.c:22:15: warning: symbol
> 'imx7ulp_clk_composite' was not declared. Should it be static?
>
> which I can fix easily by throwing in clk.h into each file.
Thanks, I will double check it when I back to office.
Regards
Dong Aisheng
Quoting Aisheng DONG (2018-12-03 17:29:29)
> > -----Original Message-----
> > From: Stephen Boyd [mailto:[email protected]]
> > Sent: Tuesday, December 4, 2018 3:32 AM
> > To: Aisheng DONG <[email protected]>; [email protected]
> > Cc: [email protected]; [email protected];
> > [email protected]; [email protected]; Anson Huang
> > <[email protected]>; Jacky Bai <[email protected]>; dl-linux-imx
> > <[email protected]>; Aisheng DONG <[email protected]>
> > Subject: Re: [PATCH V6 0/9] clk: add imx7ulp clk support
> >
> > Quoting A.s. Dong (2018-11-14 05:01:31)
> > > This patch series intends to add imx7ulp clk support.
> > >
> > > i.MX7ULP Clock functions are under joint control of the System Clock
> > > Generation (SCG) modules, Peripheral Clock Control (PCC) modules, and
> > > Core Mode Controller (CMC)1 blocks
> > >
> > > The clocking scheme provides clear separation between M4 domain and A7
> > > domain. Except for a few clock sources shared between two domains,
> > > such as the System Oscillator clock, the Slow IRC (SIRC), and and the
> > > Fast IRC clock (FIRCLK), clock sources and clock management are
> > > separated and contained within each domain.
> > >
> > > M4 clock management consists of SCG0, PCC0, PCC1, and CMC0 modules.
> > > A7 clock management consists of SCG1, PCC2, PCC3, and CMC1 modules.
> > >
> > > Note: this series only adds A7 clock domain support as M4 clock domain
> > > will be handled by M4 seperately.
> > >
> >
> > I got:
> >
> > drivers/clk/imx/clk-pllv4.c:152:15: warning: symbol 'imx_clk_pllv4' was not
> > declared. Should it be static?
> > drivers/clk/imx/clk-pfdv2.c:166:15: warning: symbol 'imx_clk_pfdv2' was not
> > declared. Should it be static?
> > drivers/clk/imx/clk-divider-gate.c:174:15: warning: symbol
> > 'imx_clk_divider_gate' was not declared. Should it be static?
> > drivers/clk/imx/clk-composite-7ulp.c:22:15: warning: symbol
> > 'imx7ulp_clk_composite' was not declared. Should it be static?
> >
> > which I can fix easily by throwing in clk.h into each file.
>
> Thanks, I will double check it when I back to office.
>
No worries, I fixed it up and merged to clk-next.
On Wed, Dec 05, 2018 at 11:41:01AM -0800, Stephen Boyd wrote:
> No worries, I fixed it up and merged to clk-next.
Hi Stephen,
In order to send imx7ulp device tree for 4.21, I pulled branch
clk-imx7ulp into IMX tree to resolve the dependency on clock ID
definitions. So please keep the branch stable, thanks.
Shawn
Quoting Shawn Guo (2018-12-10 00:14:56)
> On Wed, Dec 05, 2018 at 11:41:01AM -0800, Stephen Boyd wrote:
> > No worries, I fixed it up and merged to clk-next.
>
> Hi Stephen,
>
> In order to send imx7ulp device tree for 4.21, I pulled branch
> clk-imx7ulp into IMX tree to resolve the dependency on clock ID
> definitions. So please keep the branch stable, thanks.
>
Ok. No problem. Thanks for letting me know.