The following series of patches add support for the following
on J721S2 common processor board,
- USB
- SerDes
- OSPI
- PCIe
Changes from v1:
* Resolve issues with dt schema reporting
* Minor changes related to consistency on node naming and value
Changes from v2:
* Added PCIe RC + EP enablement patchsets
* Added device-id for j722s2 PCIe host in dt documentation
* Reworked SERDES + WIZ enablement patchset to use properies for clocks
defines versus entire devicetree nodes. Results in cleaner code that
doesn't break dt-schema or the driver functionality.
Aswath Govindraju (7):
arm64: dts: ti: k3-j721s2-main: Add support for USB
arm64: dts: ti: k3-j721s2-mcu-wakeup: Add support of OSPI
arm64: dts: ti: k3-j721s2-common-proc-board: Enable SERDES0
arm64: dts: ti: k3-j721s2-common-proc-board: Add USB support
arm64: dts: ti: k3-j721s2: Add support for OSPI Flashes
arm64: dts: ti: k3-j721s2-main: Add PCIe device tree node
arm64: dts: ti: k3-j721s2-common-proc-board: Enable PCIe
Matt Ranostay (2):
arm64: dts: ti: k3-j721s2-main: Add SERDES and WIZ device tree node
dt-bindings: PCI: Add host mode device-id for j721s2 platform
.../bindings/pci/ti,j721e-pci-host.yaml | 2 +
.../dts/ti/k3-j721s2-common-proc-board.dts | 92 +++++++++++
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 156 ++++++++++++++++++
.../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 40 +++++
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 42 +++++
5 files changed, 332 insertions(+)
--
2.37.2
From: Aswath Govindraju <[email protected]>
Add support for single instance of USB 3.0 controller in J721S2 SoC.
Cc: Vignesh Raghavendra <[email protected]>
Cc: Nishanth Menon <[email protected]>
Acked-by: Matt Ranostay <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 42 ++++++++++++++++++++++
1 file changed, 42 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index 34e7d577ae13..1f178ad3fa42 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -26,6 +26,20 @@ l3cache-sram@200000 {
};
};
+ scm_conf: syscon@104000 {
+ compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
+ reg = <0x00 0x00104000 0x00 0x18000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x00 0x00 0x00104000 0x18000>;
+
+ usb_serdes_mux: mux-controller-0 {
+ compatible = "mmio-mux";
+ #mux-control-cells = <1>;
+ mux-reg-masks = <0x0 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */
+ };
+ };
+
gic500: interrupt-controller@1800000 {
compatible = "arm,gic-v3";
#address-cells = <2>;
@@ -686,6 +700,34 @@ cpts@310d0000 {
};
};
+ usbss0: cdns-usb@4104000 {
+ compatible = "ti,j721e-usb";
+ reg = <0x00 0x04104000 0x00 0x100>;
+ clocks = <&k3_clks 360 16>, <&k3_clks 360 15>;
+ clock-names = "ref", "lpm";
+ assigned-clocks = <&k3_clks 360 16>; /* USB2_REFCLK */
+ assigned-clock-parents = <&k3_clks 360 17>;
+ power-domains = <&k3_pds 360 TI_SCI_PD_EXCLUSIVE>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ dma-coherent;
+
+ usb0: usb@6000000 {
+ compatible = "cdns,usb3";
+ reg = <0x00 0x06000000 0x00 0x10000>,
+ <0x00 0x06010000 0x00 0x10000>,
+ <0x00 0x06020000 0x00 0x10000>;
+ reg-names = "otg", "xhci", "dev";
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host", "peripheral", "otg";
+ maximum-speed = "super-speed";
+ dr_mode = "otg";
+ };
+ };
+
main_mcan0: can@2701000 {
compatible = "bosch,m_can";
reg = <0x00 0x02701000 0x00 0x200>,
--
2.37.2
From: Aswath Govindraju <[email protected]>
x1 lane PCIe slot in the common processor board is enabled and connected to
J721S2 SOM. Add PCIe DT node in common processor board to reflect the
same.
Signed-off-by: Aswath Govindraju <[email protected]>
Signed-off-by: Vignesh Raghavendra <[email protected]>
---
.../boot/dts/ti/k3-j721s2-common-proc-board.dts | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index cb99a97af426..793ee77838f4 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -428,6 +428,20 @@ flash@0{
};
};
+&pcie1_rc {
+ reset-gpios = <&exp1 2 GPIO_ACTIVE_HIGH>;
+ phys = <&serdes0_pcie_link>;
+ phy-names = "pcie-phy";
+ num-lanes = <1>;
+};
+
+&pcie1_ep {
+ phys = <&serdes0_pcie_link>;
+ phy-names = "pcie-phy";
+ num-lanes = <1>;
+ status = "disabled";
+};
+
&mcu_mcan0 {
pinctrl-names = "default";
pinctrl-0 = <&mcu_mcan0_pins_default>;
--
2.37.2
From: Aswath Govindraju <[email protected]>
Configure first lane to PCIe, the second lane to USB and the last two lanes
to eDP. Also, add sub-nodes to SERDES0 DT node to represent SERDES0 is
connected to PCIe.
Cc: Vignesh Raghavendra <[email protected]>
Cc: Nishanth Menon <[email protected]>
Acked-by: Matt Ranostay <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
---
.../dts/ti/k3-j721s2-common-proc-board.dts | 22 +++++++++++++++++++
1 file changed, 22 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index b210cc07c539..791f235bd95f 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -9,6 +9,9 @@
#include "k3-j721s2-som-p0.dtsi"
#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/phy/phy-cadence.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/mux/ti-serdes.h>
/ {
compatible = "ti,j721s2-evm", "ti,j721s2";
@@ -350,6 +353,25 @@ &cpsw_port1 {
phy-handle = <&phy0>;
};
+&serdes_ln_ctrl {
+ idle-states = <J721S2_SERDES0_LANE0_PCIE1_LANE0>, <J721S2_SERDES0_LANE1_USB>,
+ <J721S2_SERDES0_LANE2_EDP_LANE2>, <J721S2_SERDES0_LANE3_EDP_LANE3>;
+};
+
+&serdes_refclk {
+ clock-frequency = <100000000>;
+};
+
+&serdes0 {
+ serdes0_pcie_link: phy@0 {
+ reg = <0>;
+ cdns,num-lanes = <1>;
+ #phy-cells = <0>;
+ cdns,phy-type = <PHY_TYPE_PCIE>;
+ resets = <&serdes_wiz0 1>;
+ };
+};
+
&mcu_mcan0 {
pinctrl-names = "default";
pinctrl-0 = <&mcu_mcan0_pins_default>;
--
2.37.2
Add dt node for the single instance of WIZ (SERDES wrapper) and
SERDES module shared by PCIe, eDP and USB.
Cc: Vignesh Raghavendra <[email protected]>
Cc: Nishanth Menon <[email protected]>
Signed-off-by: Matt Ranostay <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 53 ++++++++++++++++++++++
1 file changed, 53 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index 1f178ad3fa42..a4260ffb75c7 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -5,6 +5,16 @@
* Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
*/
+#include <dt-bindings/phy/phy-cadence.h>
+#include <dt-bindings/phy/phy-ti.h>
+
+/ {
+ serdes_refclk: clock-cmnrefclk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ };
+};
+
&cbass_main {
msmc_ram: sram@70000000 {
compatible = "mmio-sram";
@@ -38,6 +48,13 @@ usb_serdes_mux: mux-controller-0 {
#mux-control-cells = <1>;
mux-reg-masks = <0x0 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */
};
+
+ serdes_ln_ctrl: mux-controller-80 {
+ compatible = "mmio-mux";
+ #mux-control-cells = <1>;
+ mux-reg-masks = <0x80 0x3>, <0x84 0x3>, /* SERDES0 lane0/1 select */
+ <0x88 0x3>, <0x8c 0x3>; /* SERDES0 lane2/3 select */
+ };
};
gic500: interrupt-controller@1800000 {
@@ -728,6 +745,42 @@ usb0: usb@6000000 {
};
};
+ serdes_wiz0: wiz@5060000 {
+ compatible = "ti,am64-wiz-10g";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ power-domains = <&k3_pds 365 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 365 0>, <&k3_clks 365 3>, <&serdes_refclk>;
+ clock-names = "fck", "core_ref_clk", "ext_ref_clk";
+ num-lanes = <4>;
+ #reset-cells = <1>;
+ #clock-cells = <1>;
+ ranges = <0x5060000 0x0 0x5060000 0x10000>;
+
+ assigned-clocks = <&k3_clks 365 3>;
+ assigned-clock-parents = <&k3_clks 365 7>;
+
+ serdes0: serdes@5060000 {
+ compatible = "ti,j721e-serdes-10g";
+ reg = <0x05060000 0x00010000>;
+ reg-names = "torrent_phy";
+ resets = <&serdes_wiz0 0>;
+ reset-names = "torrent_reset";
+ clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>,
+ <&serdes_wiz0 TI_WIZ_PHY_EN_REFCLK>;
+ clock-names = "refclk", "phy_en_refclk";
+ assigned-clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>,
+ <&serdes_wiz0 TI_WIZ_PLL1_REFCLK>,
+ <&serdes_wiz0 TI_WIZ_REFCLK_DIG>;
+ assigned-clock-parents = <&k3_clks 365 3>,
+ <&k3_clks 365 3>,
+ <&k3_clks 365 3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #clock-cells = <1>;
+ };
+ };
+
main_mcan0: can@2701000 {
compatible = "bosch,m_can";
reg = <0x00 0x02701000 0x00 0x200>,
--
2.37.2
From: Aswath Govindraju <[email protected]>
The board uses lane 1 of SERDES for USB. Set the mux
accordingly.
The USB controller and EVM supports super-speed for USB0
on the Type-C port. However, the SERDES has a limitation
that upto 2 protocols can be used at a time. The SERDES is
wired for PCIe, eDP and USB super-speed. It has been
chosen to use PCIe and eDP as default. So restrict
USB0 to high-speed mode.
Cc: Vignesh Raghavendra <[email protected]>
Cc: Nishanth Menon <[email protected]>
Acked-by: Matt Ranostay <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
---
.../dts/ti/k3-j721s2-common-proc-board.dts | 22 +++++++++++++++++++
1 file changed, 22 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index 791f235bd95f..aa75dc541842 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -147,6 +147,12 @@ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
J721S2_IOPAD(0x020, PIN_INPUT, 7) /* (AA23) MCAN15_RX.GPIO0_8 */
>;
};
+
+ main_usbss0_pins_default: main-usbss0-pins-default {
+ pinctrl-single,pins = <
+ J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */
+ >;
+ };
};
&wkup_pmx0 {
@@ -372,6 +378,22 @@ serdes0_pcie_link: phy@0 {
};
};
+&usb_serdes_mux {
+ idle-states = <1>; /* USB0 to SERDES lane 1 */
+};
+
+&usbss0 {
+ pinctrl-0 = <&main_usbss0_pins_default>;
+ pinctrl-names = "default";
+ ti,vbus-divider;
+ ti,usb2-only;
+};
+
+&usb0 {
+ dr_mode = "otg";
+ maximum-speed = "high-speed";
+};
+
&mcu_mcan0 {
pinctrl-names = "default";
pinctrl-0 = <&mcu_mcan0_pins_default>;
--
2.37.2
From: Aswath Govindraju <[email protected]>
Add support for two instance of OSPI in J721S2 SoC.
Cc: Vignesh Raghavendra <[email protected]>
Cc: Nishanth Menon <[email protected]>
Acked-by: Matt Ranostay <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
---
.../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 40 +++++++++++++++++++
1 file changed, 40 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
index 4d1bfabd1313..7bc268f27030 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -299,4 +299,44 @@ cpts@3d000 {
ti,cpts-periodic-outputs = <2>;
};
};
+
+ fss: syscon@47000000 {
+ compatible = "syscon", "simple-mfd";
+ reg = <0x0 0x47000000 0x0 0x100>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ ospi0: spi@47040000 {
+ compatible = "ti,am654-ospi", "cdns,qspi-nor";
+ reg = <0x00 0x47040000 0x00 0x100>,
+ <0x5 0x0000000 0x1 0x0000000>;
+ interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>;
+ cdns,fifo-depth = <256>;
+ cdns,fifo-width = <4>;
+ cdns,trigger-address = <0x0>;
+ clocks = <&k3_clks 109 5>;
+ assigned-clocks = <&k3_clks 109 5>;
+ assigned-clock-parents = <&k3_clks 109 7>;
+ assigned-clock-rates = <166666666>;
+ power-domains = <&k3_pds 109 TI_SCI_PD_EXCLUSIVE>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ ospi1: spi@47050000 {
+ compatible = "ti,am654-ospi", "cdns,qspi-nor";
+ reg = <0x00 0x47050000 0x00 0x100>,
+ <0x7 0x0000000 0x1 0x0000000>;
+ interrupts = <GIC_SPI 841 IRQ_TYPE_LEVEL_HIGH>;
+ cdns,fifo-depth = <256>;
+ cdns,fifo-width = <4>;
+ cdns,trigger-address = <0x0>;
+ clocks = <&k3_clks 110 5>;
+ power-domains = <&k3_pds 110 TI_SCI_PD_EXCLUSIVE>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ };
};
--
2.37.2
From: Aswath Govindraju <[email protected]>
J721S2 has an OSPI NOR flash on its SOM connected the OSPI0 instance and a
QSPI NOR flash on the common processor board connected to the OSPI1
instance. Add support for the same
Cc: Vignesh Raghavendra <[email protected]>
Cc: Nishanth Menon <[email protected]>
Acked-by: Matt Ranostay <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
---
.../dts/ti/k3-j721s2-common-proc-board.dts | 34 +++++++++++++++
.../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 4 +-
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 42 +++++++++++++++++++
3 files changed, 78 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index aa75dc541842..cb99a97af426 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -206,6 +206,20 @@ mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-pins-default {
J721S2_WKUP_IOPAD(0x0c8, PIN_INPUT, 7) /* (C28) WKUP_GPIO0_2 */
>;
};
+
+ mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default {
+ pinctrl-single,pins = <
+ J721S2_WKUP_IOPAD(0x040, PIN_OUTPUT, 0) /* (A19) MCU_OSPI1_CLK */
+ J721S2_WKUP_IOPAD(0x05c, PIN_OUTPUT, 0) /* (D20) MCU_OSPI1_CSn0 */
+ J721S2_WKUP_IOPAD(0x060, PIN_OUTPUT, 0) /* (C21) MCU_OSPI1_CSn1 */
+ J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (D21) MCU_OSPI1_D0 */
+ J721S2_WKUP_IOPAD(0x050, PIN_INPUT, 0) /* (G20) MCU_OSPI1_D1 */
+ J721S2_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (C20) MCU_OSPI1_D2 */
+ J721S2_WKUP_IOPAD(0x058, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */
+ J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */
+ J721S2_WKUP_IOPAD(0x044, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */
+ >;
+ };
};
&main_gpio2 {
@@ -394,6 +408,26 @@ &usb0 {
maximum-speed = "high-speed";
};
+&ospi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
+
+ flash@0{
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <40000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
&mcu_mcan0 {
pinctrl-names = "default";
pinctrl-0 = <&mcu_mcan0_pins_default>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
index 7bc268f27030..ab49f8266d10 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -301,8 +301,8 @@ cpts@3d000 {
};
fss: syscon@47000000 {
- compatible = "syscon", "simple-mfd";
- reg = <0x0 0x47000000 0x0 0x100>;
+ compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
+ reg = <0x00 0x47000000 0x00 0x100>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index 76f0ceacb6d4..a05c17dd69b6 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -39,6 +39,28 @@ transceiver0: can-phy0 {
};
};
+&wkup_pmx0 {
+ mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+ pinctrl-single,pins = <
+ J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (D19) MCU_OSPI0_CLK */
+ J721S2_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F15) MCU_OSPI0_CSn0 */
+ J721S2_WKUP_IOPAD(0x030, PIN_OUTPUT, 0) /* (G17) MCU_OSPI0_CSn1 */
+ J721S2_WKUP_IOPAD(0x038, PIN_OUTPUT, 0) /* (F14) MCU_OSPI0_CSn2 */
+ J721S2_WKUP_IOPAD(0x03c, PIN_OUTPUT, 0) /* (F17) MCU_OSPI0_CSn3 */
+ J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (C19) MCU_OSPI0_D0 */
+ J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F16) MCU_OSPI0_D1 */
+ J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (G15) MCU_OSPI0_D2 */
+ J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (F18) MCU_OSPI0_D3 */
+ J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (E19) MCU_OSPI0_D4 */
+ J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D5 */
+ J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (F19) MCU_OSPI0_D6 */
+ J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D7 */
+ J721S2_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (E18) MCU_OSPI0_DQS */
+ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20) MCU_OSPI0_LBCLKO */
+ >;
+ };
+};
+
&main_pmx0 {
main_i2c0_pins_default: main-i2c0-pins-default {
pinctrl-single,pins = <
@@ -78,6 +100,26 @@ &main_mcan16 {
phys = <&transceiver0>;
};
+&ospi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <8>;
+ spi-rx-bus-width = <8>;
+ spi-max-frequency = <25000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <4>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
&mailbox0_cluster0 {
status = "disabled";
};
--
2.37.2
From: Aswath Govindraju <[email protected]>
Add PCIe device tree node (both RC and EP) for the single PCIe
instance present in j721s2.
Signed-off-by: Aswath Govindraju <[email protected]>
Signed-off-by: Vignesh Raghavendra <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 61 ++++++++++++++++++++++
1 file changed, 61 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index a4260ffb75c7..fc4cf8b4a28b 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -781,6 +781,67 @@ serdes0: serdes@5060000 {
};
};
+ pcie1_rc: pcie@2910000 {
+ compatible = "ti,j7200-pcie-host", "ti,j721e-pcie-host";
+ reg = <0x00 0x02910000 0x00 0x1000>,
+ <0x00 0x02917000 0x00 0x400>,
+ <0x00 0x0d800000 0x00 0x00800000>,
+ <0x00 0x18000000 0x00 0x00001000>;
+ reg-names = "intd_cfg", "user_cfg", "reg", "cfg";
+ interrupt-names = "link_state";
+ interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>;
+ device_type = "pci";
+ ti,syscon-pcie-ctrl = <&scm_conf 0x074>;
+ max-link-speed = <3>;
+ num-lanes = <4>;
+ power-domains = <&k3_pds 276 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 276 41>;
+ clock-names = "fck";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ bus-range = <0x0 0xff>;
+ vendor-id = <0x104c>;
+ device-id = <0xb013>;
+ msi-map = <0x0 &gic_its 0x0 0x10000>;
+ dma-coherent;
+ ranges = <0x01000000 0x0 0x18001000 0x00 0x18001000 0x0 0x0010000>,
+ <0x02000000 0x0 0x18011000 0x00 0x18011000 0x0 0x7fef000>;
+ dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 1 &pcie1_intc 0>, /* INT A */
+ <0 0 0 2 &pcie1_intc 0>, /* INT B */
+ <0 0 0 3 &pcie1_intc 0>, /* INT C */
+ <0 0 0 4 &pcie1_intc 0>; /* INT D */
+
+ pcie1_intc: interrupt-controller {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gic500>;
+ interrupts = <GIC_SPI 324 IRQ_TYPE_EDGE_RISING>;
+ };
+ };
+
+ pcie1_ep: pcie-ep@2910000 {
+ compatible = "ti,j7200-pcie-ep", "ti,j721e-pcie-ep";
+ reg = <0x00 0x02910000 0x00 0x1000>,
+ <0x00 0x02917000 0x00 0x400>,
+ <0x00 0x0d800000 0x00 0x00800000>,
+ <0x00 0x18000000 0x00 0x08000000>;
+ reg-names = "intd_cfg", "user_cfg", "reg", "mem";
+ interrupt-names = "link_state";
+ interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>;
+ ti,syscon-pcie-ctrl = <&scm_conf 0x074>;
+ max-link-speed = <3>;
+ num-lanes = <4>;
+ power-domains = <&k3_pds 276 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 276 41>;
+ clock-names = "fck";
+ max-functions = /bits/ 8 <6>;
+ max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
+ dma-coherent;
+ };
+
main_mcan0: can@2701000 {
compatible = "bosch,m_can";
reg = <0x00 0x02701000 0x00 0x200>,
--
2.37.2
On 20:13-20220920, Matt Ranostay wrote:
> The following series of patches add support for the following
> on J721S2 common processor board,
Thanks Matt for picking these up.. however,
> Matt Ranostay (2):
> arm64: dts: ti: k3-j721s2-main: Add SERDES and WIZ device tree node
> dt-bindings: PCI: Add host mode device-id for j721s2 platform
It gets hard when we mix driver bindings with dts patches. Please do not
do that - in this case, the binding would be better go through Lorenzo
Pieralisi <[email protected]> (who needs to be in the To list)
and the corresponding list [email protected] in CC
This allows driver bindings to be independently merged of the dts
changes - also allows dts maintainers to pick patches after ensuring
bindings (and any corresponding driver changes) are merged into master
(which locks things down). please disconnect the series such that the
dts can alone be picked up without dtbs_check problems.
That said, i'd rather we rebase this after Andrew's cleanup series in
[1] and follow the same pattern for new nodes being added.
[1] https://lore.kernel.org/all/[email protected]/
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D