Hello.
This is the third patch series I'm submitting for review.
Cheers.
Arınç
Arınç ÜNAL (8):
net: dsa: mt7530: remove .mac_port_config for MT7988 and make it
optional
net: dsa: mt7530: set interrupt register only for MT7530
net: dsa: mt7530: do not use SW_PHY_RST to reset MT7531 switch
net: dsa: mt7530: get rid of useless error returns on phylink code
path
net: dsa: mt7530: get rid of priv->info->cpu_port_config()
net: dsa: mt7530: get rid of mt753x_mac_config()
net: dsa: mt7530: put initialising PCS devices code back to original
order
net: dsa: mt7530: simplify link operations and force link down on all
ports
drivers/net/dsa/mt7530.c | 251 +++++++--------------------------------
drivers/net/dsa/mt7530.h | 15 +--
2 files changed, 46 insertions(+), 220 deletions(-)
--
2.40.1
For the switch on the MT7988 SoC, the mac_port_config member for ID_MT7988
in mt753x_table is not needed as the interfaces of all MACs are already
handled on mt7988_mac_port_get_caps().
Therefore, remove the mac_port_config member from ID_MT7988 in
mt753x_table. Before calling priv->info->mac_port_config(), if there's no
mac_port_config member in mt753x_table, exit mt753x_mac_config()
successfully.
Remove calling priv->info->mac_port_config() from the sanity check as the
sanity check requires a pointer to a mac_port_config function to be
non-NULL. This will fail for MT7988 as mac_port_config won't be a member of
its info table.
Co-developed-by: Daniel Golle <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
Signed-off-by: Arınç ÜNAL <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
---
drivers/net/dsa/mt7530.c | 18 ++++--------------
1 file changed, 4 insertions(+), 14 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 8945493f9e50..c55edbda32bd 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2638,17 +2638,6 @@ static bool mt753x_is_mac_port(u32 port)
return (port == 5 || port == 6);
}
-static int
-mt7988_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
- phy_interface_t interface)
-{
- if (dsa_is_cpu_port(ds, port) &&
- interface == PHY_INTERFACE_MODE_INTERNAL)
- return 0;
-
- return -EINVAL;
-}
-
static int
mt7531_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
phy_interface_t interface)
@@ -2689,6 +2678,9 @@ mt753x_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
{
struct mt7530_priv *priv = ds->priv;
+ if (!priv->info->mac_port_config)
+ return 0;
+
return priv->info->mac_port_config(ds, port, mode, state->interface);
}
@@ -3153,7 +3145,6 @@ const struct mt753x_info mt753x_table[] = {
.phy_write_c45 = mt7531_ind_c45_phy_write,
.cpu_port_config = mt7988_cpu_port_config,
.mac_port_get_caps = mt7988_mac_port_get_caps,
- .mac_port_config = mt7988_mac_config,
},
};
EXPORT_SYMBOL_GPL(mt753x_table);
@@ -3181,8 +3172,7 @@ mt7530_probe_common(struct mt7530_priv *priv)
* properly.
*/
if (!priv->info->sw_setup || !priv->info->phy_read_c22 ||
- !priv->info->phy_write_c22 || !priv->info->mac_port_get_caps ||
- !priv->info->mac_port_config)
+ !priv->info->phy_write_c22 || !priv->info->mac_port_get_caps)
return -EINVAL;
priv->id = priv->info->id;
--
2.40.1
According to the document MT7531 Reference Manual for Development Board
v1.0, the SW_PHY_RST bit on the SYS_CTRL register doesn't exist for
MT7531. This is likely why forcing link down on all ports is necessary for
MT7531.
Therefore, do not set SW_PHY_RST on mt7531_setup().
Signed-off-by: Arınç ÜNAL <[email protected]>
---
drivers/net/dsa/mt7530.c | 6 ++----
1 file changed, 2 insertions(+), 4 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index d2e861361191..a43178b62817 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2434,14 +2434,12 @@ mt7531_setup(struct dsa_switch *ds)
val = mt7530_read(priv, MT7531_TOP_SIG_SR);
priv->p5_sgmii = !!(val & PAD_DUAL_SGMII_EN);
- /* all MACs must be forced link-down before sw reset */
+ /* Force link down on all ports before internal reset */
for (i = 0; i < MT7530_NUM_PORTS; i++)
mt7530_write(priv, MT7530_PMCR_P(i), MT7531_FORCE_LNK);
/* Reset the switch through internal reset */
- mt7530_write(priv, MT7530_SYS_CTRL,
- SYS_CTRL_PHY_RST | SYS_CTRL_SW_RST |
- SYS_CTRL_REG_RST);
+ mt7530_write(priv, MT7530_SYS_CTRL, SYS_CTRL_SW_RST | SYS_CTRL_REG_RST);
if (!priv->p5_sgmii) {
mt7531_pll_setup(priv);
--
2.40.1
Remove error returns on the cases where they are already handled with the
function the mac_port_get_caps member in mt753x_table points to.
mt7531_mac_config() is also called from mt7531_cpu_port_config() outside of
phylink but the port and interface modes are already handled there.
Change the functions and the mac_port_config function pointer to void now
that there're no error returns anymore.
Remove mt753x_is_mac_port() that used to help the said error returns.
On mt7531_mac_config(), switch to if statements to simplify the code.
Remove internal phy cases from mt753x_phylink_mac_config(), there is no
need to check the interface mode as that's already handled with the
function the mac_port_get_caps member in mt753x_table points to.
Signed-off-by: Arınç ÜNAL <[email protected]>
Acked-by: Daniel Golle <[email protected]>
Tested-by: Daniel Golle <[email protected]>
Signed-off-by: Arınç ÜNAL <[email protected]>
---
drivers/net/dsa/mt7530.c | 81 ++++++++--------------------------------
drivers/net/dsa/mt7530.h | 2 +-
2 files changed, 17 insertions(+), 66 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index a43178b62817..32db5e14a606 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2570,7 +2570,7 @@ static void mt7988_mac_port_get_caps(struct dsa_switch *ds, int port,
}
}
-static int
+static void
mt7530_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
phy_interface_t interface)
{
@@ -2580,22 +2580,14 @@ mt7530_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
mt7530_setup_port5(priv->ds, interface);
else if (port == 6)
mt7530_setup_port6(priv->ds, interface);
-
- return 0;
}
-static int mt7531_rgmii_setup(struct mt7530_priv *priv, u32 port,
- phy_interface_t interface,
- struct phy_device *phydev)
+static void mt7531_rgmii_setup(struct mt7530_priv *priv, u32 port,
+ phy_interface_t interface,
+ struct phy_device *phydev)
{
u32 val;
- if (priv->p5_sgmii) {
- dev_err(priv->dev, "RGMII mode is not available for port %d\n",
- port);
- return -EINVAL;
- }
-
val = mt7530_read(priv, MT7531_CLKGEN_CTRL);
val |= GP_CLK_EN;
val &= ~GP_MODE_MASK;
@@ -2623,20 +2615,14 @@ static int mt7531_rgmii_setup(struct mt7530_priv *priv, u32 port,
case PHY_INTERFACE_MODE_RGMII_ID:
break;
default:
- return -EINVAL;
+ break;
}
}
- mt7530_write(priv, MT7531_CLKGEN_CTRL, val);
-
- return 0;
-}
-static bool mt753x_is_mac_port(u32 port)
-{
- return (port == 5 || port == 6);
+ mt7530_write(priv, MT7531_CLKGEN_CTRL, val);
}
-static int
+static void
mt7531_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
phy_interface_t interface)
{
@@ -2644,42 +2630,21 @@ mt7531_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
struct phy_device *phydev;
struct dsa_port *dp;
- if (!mt753x_is_mac_port(port)) {
- dev_err(priv->dev, "port %d is not a MAC port\n", port);
- return -EINVAL;
- }
-
- switch (interface) {
- case PHY_INTERFACE_MODE_RGMII:
- case PHY_INTERFACE_MODE_RGMII_ID:
- case PHY_INTERFACE_MODE_RGMII_RXID:
- case PHY_INTERFACE_MODE_RGMII_TXID:
+ if (phy_interface_mode_is_rgmii(interface)) {
dp = dsa_to_port(ds, port);
phydev = dp->user->phydev;
- return mt7531_rgmii_setup(priv, port, interface, phydev);
- case PHY_INTERFACE_MODE_SGMII:
- case PHY_INTERFACE_MODE_NA:
- case PHY_INTERFACE_MODE_1000BASEX:
- case PHY_INTERFACE_MODE_2500BASEX:
- /* handled in SGMII PCS driver */
- return 0;
- default:
- return -EINVAL;
+ mt7531_rgmii_setup(priv, port, interface, phydev);
}
-
- return -EINVAL;
}
-static int
+static void
mt753x_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
const struct phylink_link_state *state)
{
struct mt7530_priv *priv = ds->priv;
- if (!priv->info->mac_port_config)
- return 0;
-
- return priv->info->mac_port_config(ds, port, mode, state->interface);
+ if (priv->info->mac_port_config)
+ priv->info->mac_port_config(ds, port, mode, state->interface);
}
static struct phylink_pcs *
@@ -2708,17 +2673,11 @@ mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
u32 mcr_cur, mcr_new;
switch (port) {
- case 0 ... 4:
- if (state->interface != PHY_INTERFACE_MODE_GMII &&
- state->interface != PHY_INTERFACE_MODE_INTERNAL)
- goto unsupported;
- break;
case 5:
if (priv->p5_interface == state->interface)
break;
- if (mt753x_mac_config(ds, port, mode, state) < 0)
- goto unsupported;
+ mt753x_mac_config(ds, port, mode, state);
if (priv->p5_intf_sel != P5_DISABLED)
priv->p5_interface = state->interface;
@@ -2727,16 +2686,10 @@ mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
if (priv->p6_interface == state->interface)
break;
- if (mt753x_mac_config(ds, port, mode, state) < 0)
- goto unsupported;
+ mt753x_mac_config(ds, port, mode, state);
priv->p6_interface = state->interface;
break;
- default:
-unsupported:
- dev_err(ds->dev, "%s: unsupported %s port: %i\n",
- __func__, phy_modes(state->interface), port);
- return;
}
mcr_cur = mt7530_read(priv, MT7530_PMCR_P(port));
@@ -2820,7 +2773,6 @@ mt7531_cpu_port_config(struct dsa_switch *ds, int port)
struct mt7530_priv *priv = ds->priv;
phy_interface_t interface;
int speed;
- int ret;
switch (port) {
case 5:
@@ -2845,9 +2797,8 @@ mt7531_cpu_port_config(struct dsa_switch *ds, int port)
else
speed = SPEED_1000;
- ret = mt7531_mac_config(ds, port, MLO_AN_FIXED, interface);
- if (ret)
- return ret;
+ mt7531_mac_config(ds, port, MLO_AN_FIXED, interface);
+
mt7530_write(priv, MT7530_PMCR_P(port),
PMCR_CPU_PORT_SETTING(priv->id));
mt753x_phylink_mac_link_up(ds, port, MLO_AN_FIXED, interface, NULL,
diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index 26a6d2160c08..4b47a5cac848 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -730,7 +730,7 @@ struct mt753x_info {
void (*mac_port_validate)(struct dsa_switch *ds, int port,
phy_interface_t interface,
unsigned long *supported);
- int (*mac_port_config)(struct dsa_switch *ds, int port,
+ void (*mac_port_config)(struct dsa_switch *ds, int port,
unsigned int mode,
phy_interface_t interface);
};
--
2.40.1
Setting this register related to interrupts is only needed for the MT7530
switch. Make an exclusive check to ensure this.
Signed-off-by: Arınç ÜNAL <[email protected]>
Acked-by: Daniel Golle <[email protected]>
Tested-by: Daniel Golle <[email protected]>
---
drivers/net/dsa/mt7530.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index c55edbda32bd..d2e861361191 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2054,7 +2054,7 @@ mt7530_setup_irq(struct mt7530_priv *priv)
}
/* This register must be set for MT7530 to properly fire interrupts */
- if (priv->id != ID_MT7531)
+ if (priv->id == ID_MT7530 || priv->id == ID_MT7621)
mt7530_set(priv, MT7530_TOP_SIG_CTRL, TOP_SIG_CTRL_NORMAL);
ret = request_threaded_irq(priv->irq, NULL, mt7530_irq_thread_fn,
--
2.40.1
There is no need for a separate function to call
priv->info->mac_port_config(). Call it from mt753x_phylink_mac_config()
instead and remove mt753x_mac_config().
Signed-off-by: Arınç ÜNAL <[email protected]>
---
drivers/net/dsa/mt7530.c | 14 ++------------
1 file changed, 2 insertions(+), 12 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 76b304f8fb87..680e59732d94 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2617,16 +2617,6 @@ mt7531_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
}
}
-static void
-mt753x_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
- const struct phylink_link_state *state)
-{
- struct mt7530_priv *priv = ds->priv;
-
- if (priv->info->mac_port_config)
- priv->info->mac_port_config(ds, port, mode, state->interface);
-}
-
static struct phylink_pcs *
mt753x_phylink_mac_select_pcs(struct dsa_switch *ds, int port,
phy_interface_t interface)
@@ -2652,8 +2642,8 @@ mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
struct mt7530_priv *priv = ds->priv;
u32 mcr_cur, mcr_new;
- if (port == 5 || port == 6)
- mt753x_mac_config(ds, port, mode, state);
+ if ((port == 5 || port == 6) && priv->info->mac_port_config)
+ priv->info->mac_port_config(ds, port, mode, state->interface);
mcr_cur = mt7530_read(priv, MT7530_PMCR_P(port));
mcr_new = mcr_cur;
--
2.40.1
The commit fae463084032 ("net: dsa: mt753x: fix pcs conversion regression")
fixes regression caused by cpu_port_config manually calling phylink
operations. cpu_port_config was deemed useless and was removed. Therefore,
put initialising PCS devices code back to its original order.
Signed-off-by: Arınç ÜNAL <[email protected]>
---
drivers/net/dsa/mt7530.c | 20 ++++++++++----------
1 file changed, 10 insertions(+), 10 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 680e59732d94..e565406d3314 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2802,17 +2802,9 @@ static int
mt753x_setup(struct dsa_switch *ds)
{
struct mt7530_priv *priv = ds->priv;
- int i, ret;
-
- /* Initialise the PCS devices */
- for (i = 0; i < priv->ds->num_ports; i++) {
- priv->pcs[i].pcs.ops = priv->info->pcs_ops;
- priv->pcs[i].pcs.neg_mode = true;
- priv->pcs[i].priv = priv;
- priv->pcs[i].port = i;
- }
+ int ret = priv->info->sw_setup(ds);
+ int i;
- ret = priv->info->sw_setup(ds);
if (ret)
return ret;
@@ -2824,6 +2816,14 @@ mt753x_setup(struct dsa_switch *ds)
if (ret && priv->irq)
mt7530_free_irq_common(priv);
+ /* Initialise the PCS devices */
+ for (i = 0; i < priv->ds->num_ports; i++) {
+ priv->pcs[i].pcs.ops = priv->info->pcs_ops;
+ priv->pcs[i].pcs.neg_mode = true;
+ priv->pcs[i].priv = priv;
+ priv->pcs[i].port = i;
+ }
+
if (priv->create_sgmii) {
ret = priv->create_sgmii(priv);
if (ret && priv->irq)
--
2.40.1
priv->info->cpu_port_config() is used for MT7531 and the switch on the
MT7988 SoC. It sets up the ports described as a CPU port earlier than the
phylink code path would do.
This function is useless as:
- Configuring the MACs can be done from the phylink_mac_config code path
instead.
- All the link configuration it does on the CPU ports are later undone with
the port_enable, phylink_mac_config, and then phylink_mac_link_up code
path [1].
priv->p5_interface and priv->p6_interface were being used to prevent
configuring the MACs from the phylink_mac_config code path. Remove them now
that they hold no purpose.
Remove priv->info->cpu_port_config(). On mt753x_phylink_mac_config, switch
to if statements to simplify the code.
Remove the definition of PMCR_CPU_PORT_SETTING() now that it holds no
purpose.
Change mt753x_cpu_port_enable() to void now that there're no error cases
left.
Link: https://lore.kernel.org/netdev/[email protected]/ [1]
Suggested-by: Russell King (Oracle) <[email protected]>
Signed-off-by: Arınç ÜNAL <[email protected]>
---
drivers/net/dsa/mt7530.c | 102 ++-------------------------------------
drivers/net/dsa/mt7530.h | 11 -----
2 files changed, 4 insertions(+), 109 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 32db5e14a606..76b304f8fb87 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -965,18 +965,10 @@ mt753x_trap_frames(struct mt7530_priv *priv)
MT753X_R0E_PORT_FW(MT753X_BPDU_CPU_ONLY));
}
-static int
+static void
mt753x_cpu_port_enable(struct dsa_switch *ds, int port)
{
struct mt7530_priv *priv = ds->priv;
- int ret;
-
- /* Setup max capability of CPU port at first */
- if (priv->info->cpu_port_config) {
- ret = priv->info->cpu_port_config(ds, port);
- if (ret)
- return ret;
- }
/* Enable Mediatek header mode on the cpu port */
mt7530_write(priv, MT7530_PVC_P(port),
@@ -1002,8 +994,6 @@ mt753x_cpu_port_enable(struct dsa_switch *ds, int port)
/* Set to fallback mode for independent VLAN learning */
mt7530_rmw(priv, MT7530_PCR_P(port), PCR_PORT_VLAN_MASK,
MT7530_PORT_FALLBACK_MODE);
-
- return 0;
}
static int
@@ -2244,8 +2234,6 @@ mt7530_setup(struct dsa_switch *ds)
val |= MHWTRAP_MANUAL;
mt7530_write(priv, MT7530_MHWTRAP, val);
- priv->p6_interface = PHY_INTERFACE_MODE_NA;
-
mt753x_trap_frames(priv);
/* Enable and reset MIB counters */
@@ -2260,9 +2248,7 @@ mt7530_setup(struct dsa_switch *ds)
mt7530_set(priv, MT7530_PSC_P(i), SA_DIS);
if (dsa_is_cpu_port(ds, i)) {
- ret = mt753x_cpu_port_enable(ds, i);
- if (ret)
- return ret;
+ mt753x_cpu_port_enable(ds, i);
} else {
mt7530_port_disable(ds, i);
@@ -2366,9 +2352,7 @@ mt7531_setup_common(struct dsa_switch *ds)
mt7530_set(priv, MT7531_DBG_CNT(i), MT7531_DIS_CLR);
if (dsa_is_cpu_port(ds, i)) {
- ret = mt753x_cpu_port_enable(ds, i);
- if (ret)
- return ret;
+ mt753x_cpu_port_enable(ds, i);
} else {
mt7530_port_disable(ds, i);
@@ -2457,10 +2441,6 @@ mt7531_setup(struct dsa_switch *ds)
mt7530_rmw(priv, MT7531_GPIO_MODE0, MT7531_GPIO0_MASK,
MT7531_GPIO0_INTERRUPT);
- /* Let phylink decide the interface later. */
- priv->p5_interface = PHY_INTERFACE_MODE_NA;
- priv->p6_interface = PHY_INTERFACE_MODE_NA;
-
/* Enable PHY core PLL, since phy_device has not yet been created
* provided for phy_[read,write]_mmd_indirect is called, we provide
* our own mt7531_ind_mmd_phy_[read,write] to complete this
@@ -2672,26 +2652,9 @@ mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
struct mt7530_priv *priv = ds->priv;
u32 mcr_cur, mcr_new;
- switch (port) {
- case 5:
- if (priv->p5_interface == state->interface)
- break;
-
+ if (port == 5 || port == 6)
mt753x_mac_config(ds, port, mode, state);
- if (priv->p5_intf_sel != P5_DISABLED)
- priv->p5_interface = state->interface;
- break;
- case 6:
- if (priv->p6_interface == state->interface)
- break;
-
- mt753x_mac_config(ds, port, mode, state);
-
- priv->p6_interface = state->interface;
- break;
- }
-
mcr_cur = mt7530_read(priv, MT7530_PMCR_P(port));
mcr_new = mcr_cur;
mcr_new &= ~PMCR_LINK_SETTINGS_MASK;
@@ -2767,61 +2730,6 @@ static void mt753x_phylink_mac_link_up(struct dsa_switch *ds, int port,
mt7530_set(priv, MT7530_PMCR_P(port), mcr);
}
-static int
-mt7531_cpu_port_config(struct dsa_switch *ds, int port)
-{
- struct mt7530_priv *priv = ds->priv;
- phy_interface_t interface;
- int speed;
-
- switch (port) {
- case 5:
- if (!priv->p5_sgmii)
- interface = PHY_INTERFACE_MODE_RGMII;
- else
- interface = PHY_INTERFACE_MODE_2500BASEX;
-
- priv->p5_interface = interface;
- break;
- case 6:
- interface = PHY_INTERFACE_MODE_2500BASEX;
-
- priv->p6_interface = interface;
- break;
- default:
- return -EINVAL;
- }
-
- if (interface == PHY_INTERFACE_MODE_2500BASEX)
- speed = SPEED_2500;
- else
- speed = SPEED_1000;
-
- mt7531_mac_config(ds, port, MLO_AN_FIXED, interface);
-
- mt7530_write(priv, MT7530_PMCR_P(port),
- PMCR_CPU_PORT_SETTING(priv->id));
- mt753x_phylink_mac_link_up(ds, port, MLO_AN_FIXED, interface, NULL,
- speed, DUPLEX_FULL, true, true);
-
- return 0;
-}
-
-static int
-mt7988_cpu_port_config(struct dsa_switch *ds, int port)
-{
- struct mt7530_priv *priv = ds->priv;
-
- mt7530_write(priv, MT7530_PMCR_P(port),
- PMCR_CPU_PORT_SETTING(priv->id));
-
- mt753x_phylink_mac_link_up(ds, port, MLO_AN_FIXED,
- PHY_INTERFACE_MODE_INTERNAL, NULL,
- SPEED_10000, DUPLEX_FULL, true, true);
-
- return 0;
-}
-
static void mt753x_phylink_get_caps(struct dsa_switch *ds, int port,
struct phylink_config *config)
{
@@ -3080,7 +2988,6 @@ const struct mt753x_info mt753x_table[] = {
.phy_write_c22 = mt7531_ind_c22_phy_write,
.phy_read_c45 = mt7531_ind_c45_phy_read,
.phy_write_c45 = mt7531_ind_c45_phy_write,
- .cpu_port_config = mt7531_cpu_port_config,
.mac_port_get_caps = mt7531_mac_port_get_caps,
.mac_port_config = mt7531_mac_config,
},
@@ -3092,7 +2999,6 @@ const struct mt753x_info mt753x_table[] = {
.phy_write_c22 = mt7531_ind_c22_phy_write,
.phy_read_c45 = mt7531_ind_c45_phy_read,
.phy_write_c45 = mt7531_ind_c45_phy_write,
- .cpu_port_config = mt7988_cpu_port_config,
.mac_port_get_caps = mt7988_mac_port_get_caps,
},
};
diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index 4b47a5cac848..caae48703547 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -311,13 +311,6 @@ enum mt7530_vlan_port_acc_frm {
PMCR_TX_FC_EN | PMCR_RX_FC_EN | \
PMCR_FORCE_FDX | PMCR_FORCE_LNK | \
PMCR_FORCE_EEE1G | PMCR_FORCE_EEE100)
-#define PMCR_CPU_PORT_SETTING(id) (PMCR_FORCE_MODE_ID((id)) | \
- PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | \
- PMCR_BACKOFF_EN | PMCR_BACKPR_EN | \
- PMCR_TX_EN | PMCR_RX_EN | \
- PMCR_TX_FC_EN | PMCR_RX_FC_EN | \
- PMCR_FORCE_SPEED_1000 | \
- PMCR_FORCE_FDX | PMCR_FORCE_LNK)
#define MT7530_PMEEECR_P(x) (0x3004 + (x) * 0x100)
#define WAKEUP_TIME_1000(x) (((x) & 0xFF) << 24)
@@ -724,7 +717,6 @@ struct mt753x_info {
int regnum);
int (*phy_write_c45)(struct mt7530_priv *priv, int port, int devad,
int regnum, u16 val);
- int (*cpu_port_config)(struct dsa_switch *ds, int port);
void (*mac_port_get_caps)(struct dsa_switch *ds, int port,
struct phylink_config *config);
void (*mac_port_validate)(struct dsa_switch *ds, int port,
@@ -750,7 +742,6 @@ struct mt753x_info {
* @ports: Holding the state among ports
* @reg_mutex: The lock for protecting among process accessing
* registers
- * @p6_interface Holding the current port 6 interface
* @p5_intf_sel: Holding the current port 5 interface select
* @p5_sgmii: Flag for distinguishing if port 5 of the MT7531 switch
* has got SGMII
@@ -772,8 +763,6 @@ struct mt7530_priv {
const struct mt753x_info *info;
unsigned int id;
bool mcm;
- phy_interface_t p6_interface;
- phy_interface_t p5_interface;
enum p5_interface_select p5_intf_sel;
bool p5_sgmii;
u8 mirror_rx;
--
2.40.1
Currently, the link operations for switch MACs are scattered across
port_enable, port_disable, phylink_mac_config, phylink_mac_link_up, and
phylink_mac_link_down.
port_enable and port_disable clears the link settings. Move that to
mt7530_setup() and mt7531_setup_common() which set up the switches. This
way, the link settings are cleared on all ports at setup, and then only
once with phylink_mac_link_down() when a link goes down.
Force link down on all ports at setup as well. This ensures that only
active ports will have their link up.
Now that the bit for setting the port on force mode is done on
mt7530_setup() and mt7531_setup_common(), get rid of PMCR_FORCE_MODE_ID()
which helped determine which bit to use for the switch model.
The "MT7621 Giga Switch Programming Guide v0.3", "MT7531 Reference Manual
for Development Board v1.0", and "MT7988A Wi-Fi 7 Generation Router
Platform: Datasheet (Open Version) v0.1" documents show that these bits are
enabled at reset:
PMCR_IFG_XMIT(1) (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_MAC_MODE (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_TX_EN
PMCR_RX_EN
PMCR_BACKOFF_EN (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_BACKPR_EN (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_TX_FC_EN
PMCR_RX_FC_EN
Remove the setting of the bits not part of PMCR_LINK_SETTINGS_MASK on
phylink_mac_config as they're already set.
Suggested-by: Vladimir Oltean <[email protected]>
Signed-off-by: Arınç ÜNAL <[email protected]>
---
drivers/net/dsa/mt7530.c | 30 +++++++++++++++++-------------
drivers/net/dsa/mt7530.h | 2 --
2 files changed, 17 insertions(+), 15 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index e565406d3314..53a9210513e2 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -1017,7 +1017,6 @@ mt7530_port_enable(struct dsa_switch *ds, int port,
priv->ports[port].enable = true;
mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
priv->ports[port].pm);
- mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK);
mutex_unlock(&priv->reg_mutex);
@@ -1037,7 +1036,6 @@ mt7530_port_disable(struct dsa_switch *ds, int port)
priv->ports[port].enable = false;
mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
PCR_MATRIX_CLR);
- mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK);
mutex_unlock(&priv->reg_mutex);
}
@@ -2240,6 +2238,14 @@ mt7530_setup(struct dsa_switch *ds)
mt7530_mib_reset(ds);
for (i = 0; i < MT7530_NUM_PORTS; i++) {
+ /* Clear link settings, make all ports operate in force mode,
+ * and force link down on all ports. PMCR_FORCE_LNK must be
+ * unset to force link down. It is not modified here as it comes
+ * unset after reset.
+ */
+ mt7530_clear(priv, MT7530_PMCR_P(i), PMCR_LINK_SETTINGS_MASK);
+ mt7530_set(priv, MT7530_PMCR_P(i), PMCR_FORCE_MODE);
+
/* Disable forwarding by default on all ports */
mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
PCR_MATRIX_CLR);
@@ -2342,6 +2348,14 @@ mt7531_setup_common(struct dsa_switch *ds)
UNU_FFP_MASK);
for (i = 0; i < MT7530_NUM_PORTS; i++) {
+ /* Clear link settings, make all ports operate in force mode,
+ * and force link down on all ports. PMCR_FORCE_LNK must be
+ * unset to force link down. It is not modified here as it comes
+ * unset after reset.
+ */
+ mt7530_clear(priv, MT7530_PMCR_P(i), PMCR_LINK_SETTINGS_MASK);
+ mt7530_set(priv, MT7530_PMCR_P(i), MT7531_FORCE_MODE);
+
/* Disable forwarding by default on all ports */
mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
PCR_MATRIX_CLR);
@@ -2640,23 +2654,13 @@ mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
const struct phylink_link_state *state)
{
struct mt7530_priv *priv = ds->priv;
- u32 mcr_cur, mcr_new;
if ((port == 5 || port == 6) && priv->info->mac_port_config)
priv->info->mac_port_config(ds, port, mode, state->interface);
- mcr_cur = mt7530_read(priv, MT7530_PMCR_P(port));
- mcr_new = mcr_cur;
- mcr_new &= ~PMCR_LINK_SETTINGS_MASK;
- mcr_new |= PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | PMCR_BACKOFF_EN |
- PMCR_BACKPR_EN | PMCR_FORCE_MODE_ID(priv->id);
-
/* Are we connected to external phy */
if (port == 5 && dsa_is_user_port(ds, 5))
- mcr_new |= PMCR_EXT_PHY;
-
- if (mcr_new != mcr_cur)
- mt7530_write(priv, MT7530_PMCR_P(port), mcr_new);
+ mt7530_set(priv, MT7530_PMCR_P(port), PMCR_EXT_PHY);
}
static void mt753x_phylink_mac_link_down(struct dsa_switch *ds, int port,
diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index caae48703547..beda61263e0d 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -304,8 +304,6 @@ enum mt7530_vlan_port_acc_frm {
MT7531_FORCE_DPX | \
MT7531_FORCE_RX_FC | \
MT7531_FORCE_TX_FC)
-#define PMCR_FORCE_MODE_ID(id) ((((id) == ID_MT7531) || ((id) == ID_MT7988)) ? \
- MT7531_FORCE_MODE : PMCR_FORCE_MODE)
#define PMCR_LINK_SETTINGS_MASK (PMCR_TX_EN | PMCR_FORCE_SPEED_1000 | \
PMCR_RX_EN | PMCR_FORCE_SPEED_100 | \
PMCR_TX_FC_EN | PMCR_RX_FC_EN | \
--
2.40.1