According to the datasheet of BMP38x and BMP390 devices, for an SPI
read operation the first byte that is returned needs to be dropped,
and the rest of the bytes are the actual data returned from the
sensor.
Fixes: 8d329309184d ("iio: pressure: bmp280: Add support for BMP380 sensor family")
Signed-off-by: Vasileios Amoiridis <[email protected]>
---
drivers/iio/pressure/bmp280-spi.c | 49 ++++++++++++++++++++++++++++++-
1 file changed, 48 insertions(+), 1 deletion(-)
diff --git a/drivers/iio/pressure/bmp280-spi.c b/drivers/iio/pressure/bmp280-spi.c
index e8a5fed07e88..1972014dca93 100644
--- a/drivers/iio/pressure/bmp280-spi.c
+++ b/drivers/iio/pressure/bmp280-spi.c
@@ -8,6 +8,7 @@
#include <linux/spi/spi.h>
#include <linux/err.h>
#include <linux/regmap.h>
+#include <linux/bits.h>
#include "bmp280.h"
@@ -35,6 +36,33 @@ static int bmp280_regmap_spi_read(void *context, const void *reg,
return spi_write_then_read(spi, reg, reg_size, val, val_size);
}
+static int bmp380_regmap_spi_read(void *context, const void *reg,
+ size_t reg_size, void *val, size_t val_size)
+{
+ struct spi_device *spi = to_spi_device(context);
+ u8 rx_buf[4];
+ ssize_t status;
+
+ /*
+ * Maximum number of consecutive bytes read for a temperature or
+ * pressure measurement is 3.
+ */
+ if (val_size > 3)
+ return -EINVAL;
+ /*
+ * According to the BMP3xx datasheets, for a basic SPI read opertion,
+ * the first byte needs to be dropped and the rest are the requested
+ * data.
+ */
+ status = spi_write_then_read(spi, reg, 1, rx_buf, val_size + 1);
+ if (status)
+ return status;
+
+ memcpy(val, rx_buf + 1, val_size);
+
+ return 0;
+}
+
static struct regmap_bus bmp280_regmap_bus = {
.write = bmp280_regmap_spi_write,
.read = bmp280_regmap_spi_read,
@@ -42,10 +70,19 @@ static struct regmap_bus bmp280_regmap_bus = {
.val_format_endian_default = REGMAP_ENDIAN_BIG,
};
+static struct regmap_bus bmp380_regmap_bus = {
+ .write = bmp280_regmap_spi_write,
+ .read = bmp380_regmap_spi_read,
+ .read_flag_mask = BIT(7),
+ .reg_format_endian_default = REGMAP_ENDIAN_BIG,
+ .val_format_endian_default = REGMAP_ENDIAN_BIG,
+};
+
static int bmp280_spi_probe(struct spi_device *spi)
{
const struct spi_device_id *id = spi_get_device_id(spi);
const struct bmp280_chip_info *chip_info;
+ struct regmap_bus *bmp_regmap_bus;
struct regmap *regmap;
int ret;
@@ -58,8 +95,18 @@ static int bmp280_spi_probe(struct spi_device *spi)
chip_info = spi_get_device_match_data(spi);
+ switch (chip_info->chip_id[0]) {
+ case BMP380_CHIP_ID:
+ case BMP390_CHIP_ID:
+ bmp_regmap_bus = &bmp380_regmap_bus;
+ break;
+ default:
+ bmp_regmap_bus = &bmp280_regmap_bus;
+ break;
+ }
+
regmap = devm_regmap_init(&spi->dev,
- &bmp280_regmap_bus,
+ bmp_regmap_bus,
&spi->dev,
chip_info->regmap_config);
if (IS_ERR(regmap)) {
--
2.25.1
On Mon, 19 Feb 2024 20:13:59 +0100
Vasileios Amoiridis <[email protected]> wrote:
> According to the datasheet of BMP38x and BMP390 devices, for an SPI
> read operation the first byte that is returned needs to be dropped,
> and the rest of the bytes are the actual data returned from the
> sensor.
>
> Fixes: 8d329309184d ("iio: pressure: bmp280: Add support for BMP380 sensor family")
No line break. The fixes tag is part of the main tag block.
I can fix that whilst applying.
Otherwise this looks fine to me.
I'll leave it on list a little longer though as both Linus and Angel
are still about and might have time to also take a look at this.
>
> Signed-off-by: Vasileios Amoiridis <[email protected]>
> ---
> drivers/iio/pressure/bmp280-spi.c | 49 ++++++++++++++++++++++++++++++-
> 1 file changed, 48 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/iio/pressure/bmp280-spi.c b/drivers/iio/pressure/bmp280-spi.c
> index e8a5fed07e88..1972014dca93 100644
> --- a/drivers/iio/pressure/bmp280-spi.c
> +++ b/drivers/iio/pressure/bmp280-spi.c
> @@ -8,6 +8,7 @@
> #include <linux/spi/spi.h>
> #include <linux/err.h>
> #include <linux/regmap.h>
> +#include <linux/bits.h>
>
> #include "bmp280.h"
>
> @@ -35,6 +36,33 @@ static int bmp280_regmap_spi_read(void *context, const void *reg,
> return spi_write_then_read(spi, reg, reg_size, val, val_size);
> }
>
> +static int bmp380_regmap_spi_read(void *context, const void *reg,
> + size_t reg_size, void *val, size_t val_size)
> +{
> + struct spi_device *spi = to_spi_device(context);
> + u8 rx_buf[4];
> + ssize_t status;
> +
> + /*
> + * Maximum number of consecutive bytes read for a temperature or
> + * pressure measurement is 3.
> + */
> + if (val_size > 3)
> + return -EINVAL;
> + /*
> + * According to the BMP3xx datasheets, for a basic SPI read opertion,
> + * the first byte needs to be dropped and the rest are the requested
> + * data.
> + */
> + status = spi_write_then_read(spi, reg, 1, rx_buf, val_size + 1);
> + if (status)
> + return status;
> +
> + memcpy(val, rx_buf + 1, val_size);
> +
> + return 0;
> +}
> +
> static struct regmap_bus bmp280_regmap_bus = {
> .write = bmp280_regmap_spi_write,
> .read = bmp280_regmap_spi_read,
> @@ -42,10 +70,19 @@ static struct regmap_bus bmp280_regmap_bus = {
> .val_format_endian_default = REGMAP_ENDIAN_BIG,
> };
>
> +static struct regmap_bus bmp380_regmap_bus = {
> + .write = bmp280_regmap_spi_write,
> + .read = bmp380_regmap_spi_read,
> + .read_flag_mask = BIT(7),
> + .reg_format_endian_default = REGMAP_ENDIAN_BIG,
> + .val_format_endian_default = REGMAP_ENDIAN_BIG,
> +};
> +
> static int bmp280_spi_probe(struct spi_device *spi)
> {
> const struct spi_device_id *id = spi_get_device_id(spi);
> const struct bmp280_chip_info *chip_info;
> + struct regmap_bus *bmp_regmap_bus;
> struct regmap *regmap;
> int ret;
>
> @@ -58,8 +95,18 @@ static int bmp280_spi_probe(struct spi_device *spi)
>
> chip_info = spi_get_device_match_data(spi);
>
> + switch (chip_info->chip_id[0]) {
> + case BMP380_CHIP_ID:
> + case BMP390_CHIP_ID:
> + bmp_regmap_bus = &bmp380_regmap_bus;
> + break;
> + default:
> + bmp_regmap_bus = &bmp280_regmap_bus;
> + break;
> + }
> +
> regmap = devm_regmap_init(&spi->dev,
> - &bmp280_regmap_bus,
> + bmp_regmap_bus,
> &spi->dev,
> chip_info->regmap_config);
> if (IS_ERR(regmap)) {
On Mon, Feb 19, 2024 at 07:42:36PM +0000, Jonathan Cameron wrote:
> On Mon, 19 Feb 2024 20:13:59 +0100
> Vasileios Amoiridis <[email protected]> wrote:
>
> > According to the datasheet of BMP38x and BMP390 devices, for an SPI
> > read operation the first byte that is returned needs to be dropped,
> > and the rest of the bytes are the actual data returned from the
> > sensor.
> >
> > Fixes: 8d329309184d ("iio: pressure: bmp280: Add support for BMP380 sensor family")
> No line break. The fixes tag is part of the main tag block.
> I can fix that whilst applying.
> Otherwise this looks fine to me.
>
> I'll leave it on list a little longer though as both Linus and Angel
> are still about and might have time to also take a look at this.
>
Thank you very much again for the quick answer. Since you can fix it while applying,
I should not annoy the mailing list with more e-mails. Just for future reference,
when you mean no line break you mean between the main block and the "Fixes" line
or between the "Fixes" line and the "Signed-off-by: ...." ?
> >
> > Signed-off-by: Vasileios Amoiridis <[email protected]>
> > ---
> > drivers/iio/pressure/bmp280-spi.c | 49 ++++++++++++++++++++++++++++++-
> > 1 file changed, 48 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/iio/pressure/bmp280-spi.c b/drivers/iio/pressure/bmp280-spi.c
> > index e8a5fed07e88..1972014dca93 100644
> > --- a/drivers/iio/pressure/bmp280-spi.c
> > +++ b/drivers/iio/pressure/bmp280-spi.c
> > @@ -8,6 +8,7 @@
> > #include <linux/spi/spi.h>
> > #include <linux/err.h>
> > #include <linux/regmap.h>
> > +#include <linux/bits.h>
> >
> > #include "bmp280.h"
> >
> > @@ -35,6 +36,33 @@ static int bmp280_regmap_spi_read(void *context, const void *reg,
> > return spi_write_then_read(spi, reg, reg_size, val, val_size);
> > }
> >
> > +static int bmp380_regmap_spi_read(void *context, const void *reg,
> > + size_t reg_size, void *val, size_t val_size)
> > +{
> > + struct spi_device *spi = to_spi_device(context);
> > + u8 rx_buf[4];
> > + ssize_t status;
> > +
> > + /*
> > + * Maximum number of consecutive bytes read for a temperature or
> > + * pressure measurement is 3.
> > + */
> > + if (val_size > 3)
> > + return -EINVAL;
> > + /*
> > + * According to the BMP3xx datasheets, for a basic SPI read opertion,
> > + * the first byte needs to be dropped and the rest are the requested
> > + * data.
> > + */
> > + status = spi_write_then_read(spi, reg, 1, rx_buf, val_size + 1);
> > + if (status)
> > + return status;
> > +
> > + memcpy(val, rx_buf + 1, val_size);
> > +
> > + return 0;
> > +}
> > +
> > static struct regmap_bus bmp280_regmap_bus = {
> > .write = bmp280_regmap_spi_write,
> > .read = bmp280_regmap_spi_read,
> > @@ -42,10 +70,19 @@ static struct regmap_bus bmp280_regmap_bus = {
> > .val_format_endian_default = REGMAP_ENDIAN_BIG,
> > };
> >
> > +static struct regmap_bus bmp380_regmap_bus = {
> > + .write = bmp280_regmap_spi_write,
> > + .read = bmp380_regmap_spi_read,
> > + .read_flag_mask = BIT(7),
> > + .reg_format_endian_default = REGMAP_ENDIAN_BIG,
> > + .val_format_endian_default = REGMAP_ENDIAN_BIG,
> > +};
> > +
> > static int bmp280_spi_probe(struct spi_device *spi)
> > {
> > const struct spi_device_id *id = spi_get_device_id(spi);
> > const struct bmp280_chip_info *chip_info;
> > + struct regmap_bus *bmp_regmap_bus;
> > struct regmap *regmap;
> > int ret;
> >
> > @@ -58,8 +95,18 @@ static int bmp280_spi_probe(struct spi_device *spi)
> >
> > chip_info = spi_get_device_match_data(spi);
> >
> > + switch (chip_info->chip_id[0]) {
> > + case BMP380_CHIP_ID:
> > + case BMP390_CHIP_ID:
> > + bmp_regmap_bus = &bmp380_regmap_bus;
> > + break;
> > + default:
> > + bmp_regmap_bus = &bmp280_regmap_bus;
> > + break;
> > + }
> > +
> > regmap = devm_regmap_init(&spi->dev,
> > - &bmp280_regmap_bus,
> > + bmp_regmap_bus,
> > &spi->dev,
> > chip_info->regmap_config);
> > if (IS_ERR(regmap)) {
>
Best regards,
Vasileios Amoiridis
On Mon, 2024-02-19 at 20:13 +0100, Vasileios Amoiridis wrote:
> According to the datasheet of BMP38x and BMP390 devices, for an SPI
> read operation the first byte that is returned needs to be dropped,
> and the rest of the bytes are the actual data returned from the
> sensor.
>
Looks good to me :)
Acked-by: Angel Iglesias <[email protected]>
Kind regards,
Angel
On Mon, Feb 19, 2024 at 08:51:45PM +0100, Vasileios Amoiridis wrote:
> On Mon, Feb 19, 2024 at 07:42:36PM +0000, Jonathan Cameron wrote:
> > On Mon, 19 Feb 2024 20:13:59 +0100
> > Vasileios Amoiridis <[email protected]> wrote:
> >
> > > According to the datasheet of BMP38x and BMP390 devices, for an SPI
> > > read operation the first byte that is returned needs to be dropped,
> > > and the rest of the bytes are the actual data returned from the
> > > sensor.
> > >
> > > Fixes: 8d329309184d ("iio: pressure: bmp280: Add support for BMP380 sensor family")
> > No line break. The fixes tag is part of the main tag block.
> > I can fix that whilst applying.
> > Otherwise this looks fine to me.
> >
> > I'll leave it on list a little longer though as both Linus and Angel
> > are still about and might have time to also take a look at this.
> >
>
> Thank you very much again for the quick answer. Since you can fix it while applying,
> I should not annoy the mailing list with more e-mails. Just for future reference,
> when you mean no line break you mean between the main block and the "Fixes" line
> or between the "Fixes" line and the "Signed-off-by: ...." ?
> > >
> > > Signed-off-by: Vasileios Amoiridis <[email protected]>
The standard pattern for the patch (as it is seen in the `git log`):
---8<---
iio: ...Subject line, summary of the change...
BLANK LINE
..Multi-line description, may contain blank lines...
BLANK LINE
..Tag block: SoB, Rb, etc. tags (may NOT contain blank lines)...
---8<---
--
With Best Regards,
Andy Shevchenko
On Mon, Feb 19, 2024 at 08:13:59PM +0100, Vasileios Amoiridis wrote:
> According to the datasheet of BMP38x and BMP390 devices, for an SPI
> read operation the first byte that is returned needs to be dropped,
> and the rest of the bytes are the actual data returned from the
> sensor.
..
> #include <linux/spi/spi.h>
> #include <linux/err.h>
> #include <linux/regmap.h>
> +#include <linux/bits.h>
I see that it's unsorted, but try to squeeze a new header to the better place
where more will be kept sorted. With given context, it should go before all
others, but it might be even better location.
..
> +static int bmp380_regmap_spi_read(void *context, const void *reg,
> + size_t reg_size, void *val, size_t val_size)
> +{
> + struct spi_device *spi = to_spi_device(context);
> + u8 rx_buf[4];
> + ssize_t status;
> +
> + /*
> + * Maximum number of consecutive bytes read for a temperature or
> + * pressure measurement is 3.
> + */
> + if (val_size > 3)
> + return -EINVAL;
> + /*
> + * According to the BMP3xx datasheets, for a basic SPI read opertion,
> + * the first byte needs to be dropped and the rest are the requested
> + * data.
> + */
> + status = spi_write_then_read(spi, reg, 1, rx_buf, val_size + 1);
> + if (status)
> + return status;
> + memcpy(val, rx_buf + 1, val_size);
Okay, endianess is defined in the regmap_bus below...
> + return 0;
> +}
--
With Best Regards,
Andy Shevchenko
On Tue, Feb 20, 2024 at 04:09:26PM +0200, Andy Shevchenko wrote:
> On Mon, Feb 19, 2024 at 08:13:59PM +0100, Vasileios Amoiridis wrote:
> > According to the datasheet of BMP38x and BMP390 devices, for an SPI
> > read operation the first byte that is returned needs to be dropped,
> > and the rest of the bytes are the actual data returned from the
> > sensor.
>
> ...
>
> > #include <linux/spi/spi.h>
> > #include <linux/err.h>
> > #include <linux/regmap.h>
> > +#include <linux/bits.h>
>
> I see that it's unsorted, but try to squeeze a new header to the better place
> where more will be kept sorted. With given context, it should go before all
> others, but it might be even better location.
>
> ...
>
So you would suggest a re-ordering of the headers with a reverse
christmas-tree? I don't see it used in the other drivers of the IIO
subsystem but I can do it as well
> > +static int bmp380_regmap_spi_read(void *context, const void *reg,
> > + size_t reg_size, void *val, size_t val_size)
> > +{
> > + struct spi_device *spi = to_spi_device(context);
> > + u8 rx_buf[4];
> > + ssize_t status;
> > +
> > + /*
> > + * Maximum number of consecutive bytes read for a temperature or
> > + * pressure measurement is 3.
> > + */
> > + if (val_size > 3)
> > + return -EINVAL;
> > + /*
> > + * According to the BMP3xx datasheets, for a basic SPI read opertion,
> > + * the first byte needs to be dropped and the rest are the requested
> > + * data.
> > + */
> > + status = spi_write_then_read(spi, reg, 1, rx_buf, val_size + 1);
> > + if (status)
> > + return status;
>
> > + memcpy(val, rx_buf + 1, val_size);
>
> Okay, endianess is defined in the regmap_bus below...
>
> > + return 0;
> > +}
>
> --
> With Best Regards,
> Andy Shevchenko
>
>
On Tue, Feb 20, 2024 at 06:46:24PM +0100, Vasileios Amoiridis wrote:
> On Tue, Feb 20, 2024 at 04:09:26PM +0200, Andy Shevchenko wrote:
> > On Mon, Feb 19, 2024 at 08:13:59PM +0100, Vasileios Amoiridis wrote:
..
> > > #include <linux/spi/spi.h>
> > > #include <linux/err.h>
> > > #include <linux/regmap.h>
> > > +#include <linux/bits.h>
> >
> > I see that it's unsorted, but try to squeeze a new header to the better place
> > where more will be kept sorted. With given context, it should go before all
> > others, but it might be even better location.
>
> So you would suggest a re-ordering of the headers with a reverse
> christmas-tree?
No. Alphabetically.
--
With Best Regards,
Andy Shevchenko
On Mon, 19 Feb 2024 20:13:59 +0100
Vasileios Amoiridis <[email protected]> wrote:
> According to the datasheet of BMP38x and BMP390 devices, for an SPI
> read operation the first byte that is returned needs to be dropped,
> and the rest of the bytes are the actual data returned from the
> sensor.
>
> Fixes: 8d329309184d ("iio: pressure: bmp280: Add support for BMP380 sensor family")
>
> Signed-off-by: Vasileios Amoiridis <[email protected]>
Applied and marked for stable - with tweaks to header order and the space above
as per discussion.
> ---
> drivers/iio/pressure/bmp280-spi.c | 49 ++++++++++++++++++++++++++++++-
> 1 file changed, 48 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/iio/pressure/bmp280-spi.c b/drivers/iio/pressure/bmp280-spi.c
> index e8a5fed07e88..1972014dca93 100644
> --- a/drivers/iio/pressure/bmp280-spi.c
> +++ b/drivers/iio/pressure/bmp280-spi.c
> @@ -8,6 +8,7 @@
> #include <linux/spi/spi.h>
> #include <linux/err.h>
> #include <linux/regmap.h>
> +#include <linux/bits.h>
>
> #include "bmp280.h"
>
> @@ -35,6 +36,33 @@ static int bmp280_regmap_spi_read(void *context, const void *reg,
> return spi_write_then_read(spi, reg, reg_size, val, val_size);
> }
>
> +static int bmp380_regmap_spi_read(void *context, const void *reg,
> + size_t reg_size, void *val, size_t val_size)
> +{
> + struct spi_device *spi = to_spi_device(context);
> + u8 rx_buf[4];
> + ssize_t status;
> +
> + /*
> + * Maximum number of consecutive bytes read for a temperature or
> + * pressure measurement is 3.
> + */
> + if (val_size > 3)
> + return -EINVAL;
> + /*
> + * According to the BMP3xx datasheets, for a basic SPI read opertion,
> + * the first byte needs to be dropped and the rest are the requested
> + * data.
> + */
> + status = spi_write_then_read(spi, reg, 1, rx_buf, val_size + 1);
> + if (status)
> + return status;
> +
> + memcpy(val, rx_buf + 1, val_size);
> +
> + return 0;
> +}
> +
> static struct regmap_bus bmp280_regmap_bus = {
> .write = bmp280_regmap_spi_write,
> .read = bmp280_regmap_spi_read,
> @@ -42,10 +70,19 @@ static struct regmap_bus bmp280_regmap_bus = {
> .val_format_endian_default = REGMAP_ENDIAN_BIG,
> };
>
> +static struct regmap_bus bmp380_regmap_bus = {
> + .write = bmp280_regmap_spi_write,
> + .read = bmp380_regmap_spi_read,
> + .read_flag_mask = BIT(7),
> + .reg_format_endian_default = REGMAP_ENDIAN_BIG,
> + .val_format_endian_default = REGMAP_ENDIAN_BIG,
> +};
> +
> static int bmp280_spi_probe(struct spi_device *spi)
> {
> const struct spi_device_id *id = spi_get_device_id(spi);
> const struct bmp280_chip_info *chip_info;
> + struct regmap_bus *bmp_regmap_bus;
> struct regmap *regmap;
> int ret;
>
> @@ -58,8 +95,18 @@ static int bmp280_spi_probe(struct spi_device *spi)
>
> chip_info = spi_get_device_match_data(spi);
>
> + switch (chip_info->chip_id[0]) {
> + case BMP380_CHIP_ID:
> + case BMP390_CHIP_ID:
> + bmp_regmap_bus = &bmp380_regmap_bus;
> + break;
> + default:
> + bmp_regmap_bus = &bmp280_regmap_bus;
> + break;
> + }
> +
> regmap = devm_regmap_init(&spi->dev,
> - &bmp280_regmap_bus,
> + bmp_regmap_bus,
> &spi->dev,
> chip_info->regmap_config);
> if (IS_ERR(regmap)) {
On Tue, 20 Feb 2024 18:46:24 +0100
Vasileios Amoiridis <[email protected]> wrote:
> On Tue, Feb 20, 2024 at 04:09:26PM +0200, Andy Shevchenko wrote:
> > On Mon, Feb 19, 2024 at 08:13:59PM +0100, Vasileios Amoiridis wrote:
> > > According to the datasheet of BMP38x and BMP390 devices, for an SPI
> > > read operation the first byte that is returned needs to be dropped,
> > > and the rest of the bytes are the actual data returned from the
> > > sensor.
> >
> > ...
> >
> > > #include <linux/spi/spi.h>
> > > #include <linux/err.h>
> > > #include <linux/regmap.h>
> > > +#include <linux/bits.h>
> >
> > I see that it's unsorted, but try to squeeze a new header to the better place
> > where more will be kept sorted. With given context, it should go before all
> > others, but it might be even better location.
> >
> > ...
> >
>
> So you would suggest a re-ordering of the headers with a reverse
> christmas-tree? I don't see it used in the other drivers of the IIO
> subsystem but I can do it as well
Separate patch + alphabetical but in blocks.
linux/*
then
linux/iio/*
then
asm/*
First 2 can be combined though if you prefer that. Any asm definitely separate.
>
> > > +static int bmp380_regmap_spi_read(void *context, const void *reg,
> > > + size_t reg_size, void *val, size_t val_size)
> > > +{
> > > + struct spi_device *spi = to_spi_device(context);
> > > + u8 rx_buf[4];
> > > + ssize_t status;
> > > +
> > > + /*
> > > + * Maximum number of consecutive bytes read for a temperature or
> > > + * pressure measurement is 3.
> > > + */
> > > + if (val_size > 3)
> > > + return -EINVAL;
> > > + /*
> > > + * According to the BMP3xx datasheets, for a basic SPI read opertion,
> > > + * the first byte needs to be dropped and the rest are the requested
> > > + * data.
> > > + */
> > > + status = spi_write_then_read(spi, reg, 1, rx_buf, val_size + 1);
> > > + if (status)
> > > + return status;
> >
> > > + memcpy(val, rx_buf + 1, val_size);
> >
> > Okay, endianess is defined in the regmap_bus below...
> >
> > > + return 0;
> > > +}
> >
> > --
> > With Best Regards,
> > Andy Shevchenko
> >
> >
>
On Sat, Feb 24, 2024 at 04:30:51PM +0000, Jonathan Cameron wrote:
> On Mon, 19 Feb 2024 20:13:59 +0100
> Vasileios Amoiridis <[email protected]> wrote:
>
> > According to the datasheet of BMP38x and BMP390 devices, for an SPI
> > read operation the first byte that is returned needs to be dropped,
> > and the rest of the bytes are the actual data returned from the
> > sensor.
> >
> > Fixes: 8d329309184d ("iio: pressure: bmp280: Add support for BMP380 sensor family")
> >
> > Signed-off-by: Vasileios Amoiridis <[email protected]>
>
> Applied and marked for stable - with tweaks to header order and the space above
> as per discussion.
Hi Jonathan,
I just got my hands on a BME280 humidity sensor and I realized that this commit,
even though it fixes the SPI support for the BMP38x and BMP390 devices, it breaks
the SPI support for BME280 and BMP58x. The problem is descirbed below, inline.
> > ---
> > drivers/iio/pressure/bmp280-spi.c | 49 ++++++++++++++++++++++++++++++-
> > 1 file changed, 48 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/iio/pressure/bmp280-spi.c b/drivers/iio/pressure/bmp280-spi.c
> > index e8a5fed07e88..1972014dca93 100644
> > --- a/drivers/iio/pressure/bmp280-spi.c
> > +++ b/drivers/iio/pressure/bmp280-spi.c
> > @@ -8,6 +8,7 @@
> > #include <linux/spi/spi.h>
> > #include <linux/err.h>
> > #include <linux/regmap.h>
> > +#include <linux/bits.h>
> >
> > #include "bmp280.h"
> >
> > @@ -35,6 +36,33 @@ static int bmp280_regmap_spi_read(void *context, const void *reg,
> > return spi_write_then_read(spi, reg, reg_size, val, val_size);
> > }
> >
> > +static int bmp380_regmap_spi_read(void *context, const void *reg,
> > + size_t reg_size, void *val, size_t val_size)
> > +{
> > + struct spi_device *spi = to_spi_device(context);
> > + u8 rx_buf[4];
> > + ssize_t status;
> > +
> > + /*
> > + * Maximum number of consecutive bytes read for a temperature or
> > + * pressure measurement is 3.
> > + */
> > + if (val_size > 3)
> > + return -EINVAL;
> > + /*
> > + * According to the BMP3xx datasheets, for a basic SPI read opertion,
> > + * the first byte needs to be dropped and the rest are the requested
> > + * data.
> > + */
> > + status = spi_write_then_read(spi, reg, 1, rx_buf, val_size + 1);
> > + if (status)
> > + return status;
> > +
> > + memcpy(val, rx_buf + 1, val_size);
> > +
> > + return 0;
> > +}
> > +
> > static struct regmap_bus bmp280_regmap_bus = {
> > .write = bmp280_regmap_spi_write,
> > .read = bmp280_regmap_spi_read,
> > @@ -42,10 +70,19 @@ static struct regmap_bus bmp280_regmap_bus = {
> > .val_format_endian_default = REGMAP_ENDIAN_BIG,
> > };
> >
> > +static struct regmap_bus bmp380_regmap_bus = {
> > + .write = bmp280_regmap_spi_write,
> > + .read = bmp380_regmap_spi_read,
> > + .read_flag_mask = BIT(7),
> > + .reg_format_endian_default = REGMAP_ENDIAN_BIG,
> > + .val_format_endian_default = REGMAP_ENDIAN_BIG,
> > +};
> > +
> > static int bmp280_spi_probe(struct spi_device *spi)
> > {
> > const struct spi_device_id *id = spi_get_device_id(spi);
> > const struct bmp280_chip_info *chip_info;
> > + struct regmap_bus *bmp_regmap_bus;
> > struct regmap *regmap;
> > int ret;
> >
> > @@ -58,8 +95,18 @@ static int bmp280_spi_probe(struct spi_device *spi)
> >
> > chip_info = spi_get_device_match_data(spi);
> >
> > + switch (chip_info->chip_id[0]) {
> > + case BMP380_CHIP_ID:
> > + case BMP390_CHIP_ID:
These chip IDs, even though they are IDs, they are not unique and they are
shared among sensors (see bmp280.h line 290). This means that this cases
are true also for BME280 and BMP58x devices which of course should not
happen because their regmap bus is the bmp280_* and not the bmp380_*.
It can easily be solved by removing the switch-case statement and adding
an if(!(strcmp(id->name,"bmp380")) which checks the name which is indeed
unique. I guess that this patch should be reverted, how should I proceed?
> > + bmp_regmap_bus = &bmp380_regmap_bus;
> > + break;
> > + default:
> > + bmp_regmap_bus = &bmp280_regmap_bus;
> > + break;
> > + }
> > +
> > regmap = devm_regmap_init(&spi->dev,
> > - &bmp280_regmap_bus,
> > + bmp_regmap_bus,
> > &spi->dev,
> > chip_info->regmap_config);
> > if (IS_ERR(regmap)) {
>
On Wed, 6 Mar 2024 19:08:29 +0100
Vasileios Amoiridis <[email protected]> wrote:
> On Sat, Feb 24, 2024 at 04:30:51PM +0000, Jonathan Cameron wrote:
> > On Mon, 19 Feb 2024 20:13:59 +0100
> > Vasileios Amoiridis <[email protected]> wrote:
> >
> > > According to the datasheet of BMP38x and BMP390 devices, for an SPI
> > > read operation the first byte that is returned needs to be dropped,
> > > and the rest of the bytes are the actual data returned from the
> > > sensor.
> > >
> > > Fixes: 8d329309184d ("iio: pressure: bmp280: Add support for BMP380 sensor family")
> > >
> > > Signed-off-by: Vasileios Amoiridis <[email protected]>
> >
> > Applied and marked for stable - with tweaks to header order and the space above
> > as per discussion.
>
> Hi Jonathan,
>
> I just got my hands on a BME280 humidity sensor and I realized that this commit,
> even though it fixes the SPI support for the BMP38x and BMP390 devices, it breaks
> the SPI support for BME280 and BMP58x. The problem is descirbed below, inline.
>
> > > ---
> > > drivers/iio/pressure/bmp280-spi.c | 49 ++++++++++++++++++++++++++++++-
> > > 1 file changed, 48 insertions(+), 1 deletion(-)
> > >
> > > diff --git a/drivers/iio/pressure/bmp280-spi.c b/drivers/iio/pressure/bmp280-spi.c
> > > index e8a5fed07e88..1972014dca93 100644
> > > --- a/drivers/iio/pressure/bmp280-spi.c
> > > +++ b/drivers/iio/pressure/bmp280-spi.c
> > > @@ -8,6 +8,7 @@
> > > #include <linux/spi/spi.h>
> > > #include <linux/err.h>
> > > #include <linux/regmap.h>
> > > +#include <linux/bits.h>
> > >
> > > #include "bmp280.h"
> > >
> > > @@ -35,6 +36,33 @@ static int bmp280_regmap_spi_read(void *context, const void *reg,
> > > return spi_write_then_read(spi, reg, reg_size, val, val_size);
> > > }
> > >
> > > +static int bmp380_regmap_spi_read(void *context, const void *reg,
> > > + size_t reg_size, void *val, size_t val_size)
> > > +{
> > > + struct spi_device *spi = to_spi_device(context);
> > > + u8 rx_buf[4];
> > > + ssize_t status;
> > > +
> > > + /*
> > > + * Maximum number of consecutive bytes read for a temperature or
> > > + * pressure measurement is 3.
> > > + */
> > > + if (val_size > 3)
> > > + return -EINVAL;
> > > + /*
> > > + * According to the BMP3xx datasheets, for a basic SPI read opertion,
> > > + * the first byte needs to be dropped and the rest are the requested
> > > + * data.
> > > + */
> > > + status = spi_write_then_read(spi, reg, 1, rx_buf, val_size + 1);
> > > + if (status)
> > > + return status;
> > > +
> > > + memcpy(val, rx_buf + 1, val_size);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > static struct regmap_bus bmp280_regmap_bus = {
> > > .write = bmp280_regmap_spi_write,
> > > .read = bmp280_regmap_spi_read,
> > > @@ -42,10 +70,19 @@ static struct regmap_bus bmp280_regmap_bus = {
> > > .val_format_endian_default = REGMAP_ENDIAN_BIG,
> > > };
> > >
> > > +static struct regmap_bus bmp380_regmap_bus = {
> > > + .write = bmp280_regmap_spi_write,
> > > + .read = bmp380_regmap_spi_read,
> > > + .read_flag_mask = BIT(7),
> > > + .reg_format_endian_default = REGMAP_ENDIAN_BIG,
> > > + .val_format_endian_default = REGMAP_ENDIAN_BIG,
> > > +};
> > > +
> > > static int bmp280_spi_probe(struct spi_device *spi)
> > > {
> > > const struct spi_device_id *id = spi_get_device_id(spi);
> > > const struct bmp280_chip_info *chip_info;
> > > + struct regmap_bus *bmp_regmap_bus;
> > > struct regmap *regmap;
> > > int ret;
> > >
> > > @@ -58,8 +95,18 @@ static int bmp280_spi_probe(struct spi_device *spi)
> > >
> > > chip_info = spi_get_device_match_data(spi);
> > >
> > > + switch (chip_info->chip_id[0]) {
> > > + case BMP380_CHIP_ID:
> > > + case BMP390_CHIP_ID:
>
> These chip IDs, even though they are IDs, they are not unique and they are
> shared among sensors (see bmp280.h line 290). This means that this cases
> are true also for BME280 and BMP58x devices which of course should not
> happen because their regmap bus is the bmp280_* and not the bmp380_*.
Gah. Anyone who can go say very rude things to bosch please do so.
There is no point in having an ID register if you don't make it change
for incompatible parts!
>
> It can easily be solved by removing the switch-case statement and adding
> an if(!(strcmp(id->name,"bmp380")) which checks the name which is indeed
> unique. I guess that this patch should be reverted, how should I proceed?
Add a flag to the chip_info structure that says whether the extra byte
is needed for a given part. Then use that to pick the regmap.
Alternative would be a pointer to the right regmap, but that is probably
messier to do.
If the fix is simple, stack it as a fix for the fix. If not we can revert
it. Unfortunately it already hit mainline before I saw your message.
Make sure you include a short rant about who bad the hardware is.
Jonathan
>
> > > + bmp_regmap_bus = &bmp380_regmap_bus;
> > > + break;
> > > + default:
> > > + bmp_regmap_bus = &bmp280_regmap_bus;
> > > + break;
> > > + }
> > > +
> > > regmap = devm_regmap_init(&spi->dev,
> > > - &bmp280_regmap_bus,
> > > + bmp_regmap_bus,
> > > &spi->dev,
> > > chip_info->regmap_config);
> > > if (IS_ERR(regmap)) {
> >