[v10]
* Split the series into domains
* Addressed comments from Viresh and Sudeep about logical CPU numbering.
The qcom-cpufreq-kryo driver is aimed to support different SOC versions.
The driver reads eFuse information and chooses the required OPP subset
by passing the OPP supported-hw parameter.
The series depends on the series from Viresh:
https://patchwork.kernel.org/patch/10418139/
The previous spin was here:
https://patchwork.kernel.org/patch/10420751/
https://patchwork.kernel.org/patch/10414761/
Ilia Lin (2):
cpufreq: Add Kryo CPU scaling driver
dt-bindings: cpufreq: Document operating-points-v2-kryo-cpu
.../devicetree/bindings/opp/kryo-cpufreq.txt | 680 +++++++++++++++++++++
drivers/cpufreq/Kconfig.arm | 10 +
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/cpufreq-dt-platdev.c | 3 +
drivers/cpufreq/qcom-cpufreq-kryo.c | 163 +++++
5 files changed, 857 insertions(+)
create mode 100644 Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c
--
1.9.1
In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors,
the CPU frequency subset and voltage value of each OPP varies
based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables
defines the voltage and frequency value based on the msm-id in SMEM
and speedbin blown in the efuse combination.
The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
to provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each OPP of
operating-points-v2 table when it is parsed by the OPP framework.
Signed-off-by: Ilia Lin <[email protected]>
---
drivers/cpufreq/Kconfig.arm | 10 +++
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/cpufreq-dt-platdev.c | 3 +
drivers/cpufreq/qcom-cpufreq-kryo.c | 163 +++++++++++++++++++++++++++++++++++
4 files changed, 177 insertions(+)
create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index de55c7d..0bfd40e 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -124,6 +124,16 @@ config ARM_OMAP2PLUS_CPUFREQ
depends on ARCH_OMAP2PLUS
default ARCH_OMAP2PLUS
+config ARM_QCOM_CPUFREQ_KRYO
+ bool "Qualcomm Kryo based CPUFreq"
+ depends on QCOM_QFPROM
+ depends on QCOM_SMEM
+ select PM_OPP
+ help
+ This adds the CPUFreq driver for Qualcomm Kryo SoC based boards.
+
+ If in doubt, say N.
+
config ARM_S3C_CPUFREQ
bool
help
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index 8d24ade..fb4a2ec 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -65,6 +65,7 @@ obj-$(CONFIG_MACH_MVEBU_V7) += mvebu-cpufreq.o
obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ) += omap-cpufreq.o
obj-$(CONFIG_ARM_PXA2xx_CPUFREQ) += pxa2xx-cpufreq.o
obj-$(CONFIG_PXA3xx) += pxa3xx-cpufreq.o
+obj-$(CONFIG_ARM_QCOM_CPUFREQ_KRYO) += qcom-cpufreq-kryo.o
obj-$(CONFIG_ARM_S3C2410_CPUFREQ) += s3c2410-cpufreq.o
obj-$(CONFIG_ARM_S3C2412_CPUFREQ) += s3c2412-cpufreq.o
obj-$(CONFIG_ARM_S3C2416_CPUFREQ) += s3c2416-cpufreq.o
diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c
index 3b585e4..77d6ab8 100644
--- a/drivers/cpufreq/cpufreq-dt-platdev.c
+++ b/drivers/cpufreq/cpufreq-dt-platdev.c
@@ -118,6 +118,9 @@
{ .compatible = "nvidia,tegra124", },
+ { .compatible = "qcom,apq8096", },
+ { .compatible = "qcom,msm8996", },
+
{ .compatible = "st,stih407", },
{ .compatible = "st,stih410", },
diff --git a/drivers/cpufreq/qcom-cpufreq-kryo.c b/drivers/cpufreq/qcom-cpufreq-kryo.c
new file mode 100644
index 0000000..885051e
--- /dev/null
+++ b/drivers/cpufreq/qcom-cpufreq-kryo.c
@@ -0,0 +1,163 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ */
+
+/*
+ * In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors,
+ * the CPU frequency subset and voltage value of each OPP varies
+ * based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables
+ * defines the voltage and frequency value based on the msm-id in SMEM
+ * and speedbin blown in the efuse combination.
+ * The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
+ * to provide the OPP framework with required information.
+ * This is used to determine the voltage and frequency value for each OPP of
+ * operating-points-v2 table when it is parsed by the OPP framework.
+ */
+
+#include <linux/cpu.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_opp.h>
+#include <linux/slab.h>
+#include <linux/soc/qcom/smem.h>
+
+#define MSM_ID_SMEM 137
+
+enum _msm_id {
+ MSM8996V3 = 0xF6ul,
+ APQ8096V3 = 0x123ul,
+ MSM8996SG = 0x131ul,
+ APQ8096SG = 0x138ul,
+};
+
+enum _msm8996_version {
+ MSM8996_V3,
+ MSM8996_SG,
+ NUM_OF_MSM8996_VERSIONS,
+};
+
+static enum _msm8996_version __init qcom_cpufreq_kryo_get_msm_id(void)
+{
+ size_t len;
+ u32 *msm_id;
+ enum _msm8996_version version;
+
+ msm_id = qcom_smem_get(QCOM_SMEM_HOST_ANY, MSM_ID_SMEM, &len);
+ /* The first 4 bytes are format, next to them is the actual msm-id */
+ msm_id++;
+
+ switch ((enum _msm_id)*msm_id) {
+ case MSM8996V3:
+ case APQ8096V3:
+ version = MSM8996_V3;
+ break;
+ case MSM8996SG:
+ case APQ8096SG:
+ version = MSM8996_SG;
+ break;
+ default:
+ version = NUM_OF_MSM8996_VERSIONS;
+ }
+
+ return version;
+}
+
+static int __init qcom_cpufreq_kryo_driver_init(void)
+{
+ struct opp_table *opp_tables[NR_CPUS] = {0};
+ enum _msm8996_version msm8996_version;
+ struct nvmem_cell *speedbin_nvmem;
+ struct platform_device *pdev;
+ struct device_node *np;
+ struct device *cpu_dev;
+ unsigned cpu;
+ u8 *speedbin;
+ u32 versions;
+ size_t len;
+ int ret;
+
+ cpu_dev = get_cpu_device(0);
+ if (NULL == cpu_dev)
+ return -ENODEV;
+
+ msm8996_version = qcom_cpufreq_kryo_get_msm_id();
+ if (NUM_OF_MSM8996_VERSIONS == msm8996_version) {
+ dev_err(cpu_dev, "Not Snapdragon 820/821!");
+ return -ENODEV;
+ }
+
+ np = dev_pm_opp_of_get_opp_desc_node(cpu_dev);
+ if (IS_ERR(np))
+ return PTR_ERR(np);
+
+ if (!of_device_is_compatible(np, "operating-points-v2-kryo-cpu")) {
+ ret = -ENOENT;
+ goto free_np;
+ }
+
+ speedbin_nvmem = of_nvmem_cell_get(np, NULL);
+ if (IS_ERR(speedbin_nvmem)) {
+ ret = PTR_ERR(speedbin_nvmem);
+ dev_err(cpu_dev, "Could not get nvmem cell: %d\n", ret);
+ goto free_np;
+ }
+
+ speedbin = nvmem_cell_read(speedbin_nvmem, &len);
+ nvmem_cell_put(speedbin_nvmem);
+
+ switch (msm8996_version) {
+ case MSM8996_V3:
+ versions = 1 << (unsigned int)(*speedbin);
+ break;
+ case MSM8996_SG:
+ versions = 1 << ((unsigned int)(*speedbin) + 4);
+ break;
+ default:
+ BUG();
+ break;
+ }
+
+ for_each_possible_cpu(cpu) {
+ cpu_dev = get_cpu_device(cpu);
+ if (NULL == cpu_dev) {
+ ret = -ENODEV;
+ goto free_opp;
+ }
+
+ opp_tables[cpu] = dev_pm_opp_set_supported_hw(cpu_dev,
+ &versions, 1);
+ if (IS_ERR(opp_tables[cpu])) {
+ ret = PTR_ERR(opp_tables[cpu]);
+ dev_err(cpu_dev, "Failed to set supported hardware\n");
+ goto free_opp;
+ }
+ }
+
+ pdev = platform_device_register_simple("cpufreq-dt", -1, NULL, 0);
+ if (!IS_ERR(pdev))
+ return 0;
+
+ ret = PTR_ERR(pdev);
+ dev_err(cpu_dev, "Failed to register platform device\n");
+
+free_opp:
+ for_each_possible_cpu(cpu) {
+ if (IS_ERR_OR_NULL(opp_tables[cpu]))
+ break;
+ dev_pm_opp_put_supported_hw(opp_tables[cpu]);
+ }
+free_np:
+ of_node_put(np);
+
+ return ret;
+}
+late_initcall(qcom_cpufreq_kryo_driver_init);
+
+MODULE_DESCRIPTION("Qualcomm Technologies, Inc. Kryo CPUfreq driver");
+MODULE_LICENSE("GPL v2");
--
1.9.1
The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
to provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each OPP of
operating-points-v2 table when it is parsed by the OPP framework.
This change adds documentation for the DT bindings.
The "operating-points-v2-kryo-cpu" DT extends the "operating-points-v2"
with following parameters:
- nvmem-cells (NVMEM area containig the speedbin information)
- opp-supported-hw: A single 32 bit bitmap value,
representing compatible HW:
0: MSM8996 V3, speedbin 0
1: MSM8996 V3, speedbin 1
2: MSM8996 V3, speedbin 2
3: unused
4: MSM8996 SG, speedbin 0
5: MSM8996 SG, speedbin 1
6: MSM8996 SG, speedbin 2
7-31: unused
Signed-off-by: Ilia Lin <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Acked-by: Viresh Kumar <[email protected]>
---
.../devicetree/bindings/opp/kryo-cpufreq.txt | 680 +++++++++++++++++++++
1 file changed, 680 insertions(+)
create mode 100644 Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
diff --git a/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
new file mode 100644
index 0000000..c2127b9
--- /dev/null
+++ b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
@@ -0,0 +1,680 @@
+Qualcomm Technologies, Inc. KRYO CPUFreq and OPP bindings
+===================================
+
+In Certain Qualcomm Technologies, Inc. SoCs like apq8096 and msm8996
+that have KRYO processors, the CPU ferequencies subset and voltage value
+of each OPP varies based on the silicon variant in use.
+Qualcomm Technologies, Inc. Process Voltage Scaling Tables
+defines the voltage and frequency value based on the msm-id in SMEM
+and speedbin blown in the efuse combination.
+The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
+to provide the OPP framework with required information (existing HW bitmap).
+This is used to determine the voltage and frequency value for each OPP of
+operating-points-v2 table when it is parsed by the OPP framework.
+
+Required properties:
+--------------------
+In 'cpus' nodes:
+- operating-points-v2: Phandle to the operating-points-v2 table to use.
+
+In 'operating-points-v2' table:
+- compatible: Should be
+ - 'operating-points-v2-kryo-cpu' for apq8096 and msm8996.
+- nvmem-cells: A phandle pointing to a nvmem-cells node representing the
+ efuse registers that has information about the
+ speedbin that is used to select the right frequency/voltage
+ value pair.
+ Please refer the for nvmem-cells
+ bindings Documentation/devicetree/bindings/nvmem/nvmem.txt
+ and also examples below.
+
+In every OPP node:
+- opp-supported-hw: A single 32 bit bitmap value, representing compatible HW.
+ Bitmap:
+ 0: MSM8996 V3, speedbin 0
+ 1: MSM8996 V3, speedbin 1
+ 2: MSM8996 V3, speedbin 2
+ 3: unused
+ 4: MSM8996 SG, speedbin 0
+ 5: MSM8996 SG, speedbin 1
+ 6: MSM8996 SG, speedbin 2
+ 7-31: unused
+
+Example 1:
+---------
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ CPU0: cpu@0 {
+ device_type = "cpu";
+ compatible = "qcom,kryo";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ clocks = <&kryocc 0>;
+ cpu-supply = <&pm8994_s11_saw>;
+ operating-points-v2 = <&cluster0_opp>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_0>;
+ L2_0: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ CPU1: cpu@1 {
+ device_type = "cpu";
+ compatible = "qcom,kryo";
+ reg = <0x0 0x1>;
+ enable-method = "psci";
+ clocks = <&kryocc 0>;
+ cpu-supply = <&pm8994_s11_saw>;
+ operating-points-v2 = <&cluster0_opp>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU2: cpu@100 {
+ device_type = "cpu";
+ compatible = "qcom,kryo";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ clocks = <&kryocc 1>;
+ cpu-supply = <&pm8994_s11_saw>;
+ operating-points-v2 = <&cluster1_opp>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_1>;
+ L2_1: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ CPU3: cpu@101 {
+ device_type = "cpu";
+ compatible = "qcom,kryo";
+ reg = <0x0 0x101>;
+ enable-method = "psci";
+ clocks = <&kryocc 1>;
+ cpu-supply = <&pm8994_s11_saw>;
+ operating-points-v2 = <&cluster1_opp>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_1>;
+ };
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&CPU0>;
+ };
+
+ core1 {
+ cpu = <&CPU1>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&CPU2>;
+ };
+
+ core1 {
+ cpu = <&CPU3>;
+ };
+ };
+ };
+ };
+
+ cluster0_opp: opp_table0 {
+ compatible = "operating-points-v2-kryo-cpu";
+ nvmem-cells = <&speedbin_efuse>;
+ opp-shared;
+
+ opp-307200000 {
+ opp-hz = /bits/ 64 <307200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x77>;
+ clock-latency-ns = <200000>;
+ };
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-422400000 {
+ opp-hz = /bits/ 64 <422400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-460800000 {
+ opp-hz = /bits/ 64 <460800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-537600000 {
+ opp-hz = /bits/ 64 <537600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-556800000 {
+ opp-hz = /bits/ 64 <556800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-614400000 {
+ opp-hz = /bits/ 64 <614400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-652800000 {
+ opp-hz = /bits/ 64 <652800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-691200000 {
+ opp-hz = /bits/ 64 <691200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-729600000 {
+ opp-hz = /bits/ 64 <729600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-768000000 {
+ opp-hz = /bits/ 64 <768000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-844800000 {
+ opp-hz = /bits/ 64 <844800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x77>;
+ clock-latency-ns = <200000>;
+ };
+ opp-902400000 {
+ opp-hz = /bits/ 64 <902400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-960000000 {
+ opp-hz = /bits/ 64 <960000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-979200000 {
+ opp-hz = /bits/ 64 <979200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1036800000 {
+ opp-hz = /bits/ 64 <1036800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1056000000 {
+ opp-hz = /bits/ 64 <1056000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1113600000 {
+ opp-hz = /bits/ 64 <1113600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1132800000 {
+ opp-hz = /bits/ 64 <1132800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1190400000 {
+ opp-hz = /bits/ 64 <1190400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1209600000 {
+ opp-hz = /bits/ 64 <1209600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1228800000 {
+ opp-hz = /bits/ 64 <1228800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1286400000 {
+ opp-hz = /bits/ 64 <1286400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1324800000 {
+ opp-hz = /bits/ 64 <1324800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x5>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1363200000 {
+ opp-hz = /bits/ 64 <1363200000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x72>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1401600000 {
+ opp-hz = /bits/ 64 <1401600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x5>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1440000000 {
+ opp-hz = /bits/ 64 <1440000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1478400000 {
+ opp-hz = /bits/ 64 <1478400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1497600000 {
+ opp-hz = /bits/ 64 <1497600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x4>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1516800000 {
+ opp-hz = /bits/ 64 <1516800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1593600000 {
+ opp-hz = /bits/ 64 <1593600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x71>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1996800000 {
+ opp-hz = /bits/ 64 <1996800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x20>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2188800000 {
+ opp-hz = /bits/ 64 <2188800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x10>;
+ clock-latency-ns = <200000>;
+ };
+ };
+
+ cluster1_opp: opp_table1 {
+ compatible = "operating-points-v2-kryo-cpu";
+ nvmem-cells = <&speedbin_efuse>;
+ opp-shared;
+
+ opp-307200000 {
+ opp-hz = /bits/ 64 <307200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x77>;
+ clock-latency-ns = <200000>;
+ };
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-403200000 {
+ opp-hz = /bits/ 64 <403200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-460800000 {
+ opp-hz = /bits/ 64 <460800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-537600000 {
+ opp-hz = /bits/ 64 <537600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-556800000 {
+ opp-hz = /bits/ 64 <556800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-614400000 {
+ opp-hz = /bits/ 64 <614400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-652800000 {
+ opp-hz = /bits/ 64 <652800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-691200000 {
+ opp-hz = /bits/ 64 <691200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-729600000 {
+ opp-hz = /bits/ 64 <729600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-748800000 {
+ opp-hz = /bits/ 64 <748800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-806400000 {
+ opp-hz = /bits/ 64 <806400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-825600000 {
+ opp-hz = /bits/ 64 <825600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-883200000 {
+ opp-hz = /bits/ 64 <883200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-902400000 {
+ opp-hz = /bits/ 64 <902400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-940800000 {
+ opp-hz = /bits/ 64 <940800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-979200000 {
+ opp-hz = /bits/ 64 <979200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1036800000 {
+ opp-hz = /bits/ 64 <1036800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1056000000 {
+ opp-hz = /bits/ 64 <1056000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1113600000 {
+ opp-hz = /bits/ 64 <1113600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1132800000 {
+ opp-hz = /bits/ 64 <1132800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1190400000 {
+ opp-hz = /bits/ 64 <1190400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1209600000 {
+ opp-hz = /bits/ 64 <1209600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1248000000 {
+ opp-hz = /bits/ 64 <1248000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1286400000 {
+ opp-hz = /bits/ 64 <1286400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1324800000 {
+ opp-hz = /bits/ 64 <1324800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1363200000 {
+ opp-hz = /bits/ 64 <1363200000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1401600000 {
+ opp-hz = /bits/ 64 <1401600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1440000000 {
+ opp-hz = /bits/ 64 <1440000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1478400000 {
+ opp-hz = /bits/ 64 <1478400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1516800000 {
+ opp-hz = /bits/ 64 <1516800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1555200000 {
+ opp-hz = /bits/ 64 <1555200000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1593600000 {
+ opp-hz = /bits/ 64 <1593600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1632000000 {
+ opp-hz = /bits/ 64 <1632000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1670400000 {
+ opp-hz = /bits/ 64 <1670400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1708800000 {
+ opp-hz = /bits/ 64 <1708800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1747200000 {
+ opp-hz = /bits/ 64 <1747200000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1785600000 {
+ opp-hz = /bits/ 64 <1785600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1804800000 {
+ opp-hz = /bits/ 64 <1804800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x6>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1824000000 {
+ opp-hz = /bits/ 64 <1824000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x71>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1900800000 {
+ opp-hz = /bits/ 64 <1900800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x74>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1920000000 {
+ opp-hz = /bits/ 64 <1920000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1977600000 {
+ opp-hz = /bits/ 64 <1977600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x30>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1996800000 {
+ opp-hz = /bits/ 64 <1996800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2054400000 {
+ opp-hz = /bits/ 64 <2054400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x30>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2073600000 {
+ opp-hz = /bits/ 64 <2073600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2150400000 {
+ opp-hz = /bits/ 64 <2150400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x31>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2246400000 {
+ opp-hz = /bits/ 64 <2246400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x10>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2342400000 {
+ opp-hz = /bits/ 64 <2342400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x10>;
+ clock-latency-ns = <200000>;
+ };
+ };
+
+....
+
+reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+....
+ smem_mem: smem-mem@86000000 {
+ reg = <0x0 0x86000000 0x0 0x200000>;
+ no-map;
+ };
+....
+};
+
+smem {
+ compatible = "qcom,smem";
+ memory-region = <&smem_mem>;
+ hwlocks = <&tcsr_mutex 3>;
+};
+
+soc {
+....
+ qfprom: qfprom@74000 {
+ compatible = "qcom,qfprom";
+ reg = <0x00074000 0x8ff>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ....
+ speedbin_efuse: speedbin@133 {
+ reg = <0x133 0x1>;
+ bits = <5 3>;
+ };
+ };
+};
--
1.9.1
On 23-05-18, 12:40, Ilia Lin wrote:
> In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors,
> the CPU frequency subset and voltage value of each OPP varies
> based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables
> defines the voltage and frequency value based on the msm-id in SMEM
> and speedbin blown in the efuse combination.
> The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
> to provide the OPP framework with required information.
> This is used to determine the voltage and frequency value for each OPP of
> operating-points-v2 table when it is parsed by the OPP framework.
>
> Signed-off-by: Ilia Lin <[email protected]>
Well I gave you an Ack and you should have kept it here :(
> +static int __init qcom_cpufreq_kryo_driver_init(void)
> +{
> + struct opp_table *opp_tables[NR_CPUS] = {0};
> + enum _msm8996_version msm8996_version;
> + struct nvmem_cell *speedbin_nvmem;
> + struct platform_device *pdev;
> + struct device_node *np;
> + struct device *cpu_dev;
> + unsigned cpu;
> + u8 *speedbin;
> + u32 versions;
> + size_t len;
> + int ret;
> +
> + cpu_dev = get_cpu_device(0);
> + if (NULL == cpu_dev)
> + return -ENODEV;
> +
> + msm8996_version = qcom_cpufreq_kryo_get_msm_id();
> + if (NUM_OF_MSM8996_VERSIONS == msm8996_version) {
> + dev_err(cpu_dev, "Not Snapdragon 820/821!");
> + return -ENODEV;
> + }
> +
> + np = dev_pm_opp_of_get_opp_desc_node(cpu_dev);
> + if (IS_ERR(np))
> + return PTR_ERR(np);
> +
> + if (!of_device_is_compatible(np, "operating-points-v2-kryo-cpu")) {
> + ret = -ENOENT;
> + goto free_np;
As Russell pointed out, drop this goto here and write:
of_node_put(np);
return -ENOENT;
}
> + }
> +
> + speedbin_nvmem = of_nvmem_cell_get(np, NULL);
And do the same here unconditionally as you don't need to use np
anymore, i.e.
of_node_put(np);
> + if (IS_ERR(speedbin_nvmem)) {
> + ret = PTR_ERR(speedbin_nvmem);
> + dev_err(cpu_dev, "Could not get nvmem cell: %d\n", ret);
> + goto free_np;
> + }
> +
> + speedbin = nvmem_cell_read(speedbin_nvmem, &len);
> + nvmem_cell_put(speedbin_nvmem);
> +
> + switch (msm8996_version) {
> + case MSM8996_V3:
> + versions = 1 << (unsigned int)(*speedbin);
> + break;
> + case MSM8996_SG:
> + versions = 1 << ((unsigned int)(*speedbin) + 4);
> + break;
> + default:
> + BUG();
> + break;
> + }
> +
> + for_each_possible_cpu(cpu) {
> + cpu_dev = get_cpu_device(cpu);
> + if (NULL == cpu_dev) {
> + ret = -ENODEV;
> + goto free_opp;
> + }
> +
> + opp_tables[cpu] = dev_pm_opp_set_supported_hw(cpu_dev,
> + &versions, 1);
> + if (IS_ERR(opp_tables[cpu])) {
> + ret = PTR_ERR(opp_tables[cpu]);
> + dev_err(cpu_dev, "Failed to set supported hardware\n");
> + goto free_opp;
> + }
> + }
> +
> + pdev = platform_device_register_simple("cpufreq-dt", -1, NULL, 0);
> + if (!IS_ERR(pdev))
> + return 0;
> +
> + ret = PTR_ERR(pdev);
> + dev_err(cpu_dev, "Failed to register platform device\n");
> +
> +free_opp:
> + for_each_possible_cpu(cpu) {
> + if (IS_ERR_OR_NULL(opp_tables[cpu]))
> + break;
> + dev_pm_opp_put_supported_hw(opp_tables[cpu]);
> + }
> +free_np:
> + of_node_put(np);
And then you can remove the label and above statement.
> +
> + return ret;
> +}
> +late_initcall(qcom_cpufreq_kryo_driver_init);
> +
> +MODULE_DESCRIPTION("Qualcomm Technologies, Inc. Kryo CPUfreq driver");
> +MODULE_LICENSE("GPL v2");
> --
> 1.9.1
--
viresh
On 23/05/18 10:40, Ilia Lin wrote:
> In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors,
> the CPU frequency subset and voltage value of each OPP varies
> based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables
> defines the voltage and frequency value based on the msm-id in SMEM
> and speedbin blown in the efuse combination.
> The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
> to provide the OPP framework with required information.
> This is used to determine the voltage and frequency value for each OPP of
> operating-points-v2 table when it is parsed by the OPP framework.
>
> Signed-off-by: Ilia Lin <[email protected]>
[...]
> + pdev = platform_device_register_simple("cpufreq-dt", -1, NULL, 0);
> + if (!IS_ERR(pdev))
> + return 0;
> +
> + ret = PTR_ERR(pdev);
> + dev_err(cpu_dev, "Failed to register platform device\n");
> +
> +free_opp:
> + for_each_possible_cpu(cpu) {
> + if (IS_ERR_OR_NULL(opp_tables[cpu]))
> + break;
> + dev_pm_opp_put_supported_hw(opp_tables[cpu]);
> + }
> +free_np:
> + of_node_put(np);
> +
> + return ret;
> +}
> +late_initcall(qcom_cpufreq_kryo_driver_init);
Any particular reason why this *has* to be late initcall ?
Please change it to module_initcall otherwise.
Also address the of_node comments from Viresh.
Otherwise, it looks good.
--
Regards,
Sudeep
> -----Original Message-----
> From: Sudeep Holla <[email protected]>
> Sent: Wednesday, May 23, 2018 13:40
> To: Ilia Lin <[email protected]>; [email protected]; [email protected];
> [email protected]; [email protected]; [email protected];
> [email protected]; [email protected]; [email protected];
> [email protected]
> Cc: Sudeep Holla <[email protected]>
> Subject: Re: [PATCH v10 1/2] cpufreq: Add Kryo CPU scaling driver
>
>
>
> On 23/05/18 10:40, Ilia Lin wrote:
> > In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO
> > processors, the CPU frequency subset and voltage value of each OPP
> > varies based on the silicon variant in use. Qualcomm Process Voltage
> > Scaling Tables defines the voltage and frequency value based on the
> > msm-id in SMEM and speedbin blown in the efuse combination.
> > The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the
> > SoC to provide the OPP framework with required information.
> > This is used to determine the voltage and frequency value for each OPP
> > of
> > operating-points-v2 table when it is parsed by the OPP framework.
> >
> > Signed-off-by: Ilia Lin <[email protected]>
>
> [...]
>
> > + pdev = platform_device_register_simple("cpufreq-dt", -1, NULL, 0);
> > + if (!IS_ERR(pdev))
> > + return 0;
> > +
> > + ret = PTR_ERR(pdev);
> > + dev_err(cpu_dev, "Failed to register platform device\n");
> > +
> > +free_opp:
> > + for_each_possible_cpu(cpu) {
> > + if (IS_ERR_OR_NULL(opp_tables[cpu]))
> > + break;
> > + dev_pm_opp_put_supported_hw(opp_tables[cpu]);
> > + }
> > +free_np:
> > + of_node_put(np);
> > +
> > + return ret;
> > +}
> > +late_initcall(qcom_cpufreq_kryo_driver_init);
>
> Any particular reason why this *has* to be late initcall ?
> Please change it to module_initcall otherwise.
The purpose is to give the cpufreq-dt the time to register the driver and only then my driver will add the platform device.
> Also address the of_node comments from Viresh.
>
> Otherwise, it looks good.
> --
> Regards,
> Sudeep
On 23 May 2018 at 16:36, <[email protected]> wrote:
>
>
>> -----Original Message-----
>> From: Sudeep Holla <[email protected]>
>> Sent: Wednesday, May 23, 2018 13:40
>> To: Ilia Lin <[email protected]>; [email protected]; [email protected];
>> [email protected]; [email protected]; [email protected];
>> [email protected]; [email protected]; [email protected];
>> [email protected]
>> Cc: Sudeep Holla <[email protected]>
>> Subject: Re: [PATCH v10 1/2] cpufreq: Add Kryo CPU scaling driver
>>
>>
>>
>> On 23/05/18 10:40, Ilia Lin wrote:
>> > In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO
>> > processors, the CPU frequency subset and voltage value of each OPP
>> > varies based on the silicon variant in use. Qualcomm Process Voltage
>> > Scaling Tables defines the voltage and frequency value based on the
>> > msm-id in SMEM and speedbin blown in the efuse combination.
>> > The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the
>> > SoC to provide the OPP framework with required information.
>> > This is used to determine the voltage and frequency value for each OPP
>> > of
>> > operating-points-v2 table when it is parsed by the OPP framework.
>> >
>> > Signed-off-by: Ilia Lin <[email protected]>
>>
>> [...]
>>
>> > + pdev = platform_device_register_simple("cpufreq-dt", -1, NULL, 0);
>> > + if (!IS_ERR(pdev))
>> > + return 0;
>> > +
>> > + ret = PTR_ERR(pdev);
>> > + dev_err(cpu_dev, "Failed to register platform device\n");
>> > +
>> > +free_opp:
>> > + for_each_possible_cpu(cpu) {
>> > + if (IS_ERR_OR_NULL(opp_tables[cpu]))
>> > + break;
>> > + dev_pm_opp_put_supported_hw(opp_tables[cpu]);
>> > + }
>> > +free_np:
>> > + of_node_put(np);
>> > +
>> > + return ret;
>> > +}
>> > +late_initcall(qcom_cpufreq_kryo_driver_init);
>>
>> Any particular reason why this *has* to be late initcall ?
>> Please change it to module_initcall otherwise.
>
> The purpose is to give the cpufreq-dt the time to register the driver and only then my driver will add the platform device.
That isn't required, the device and its driver can be registered in any order.
> -----Original Message-----
> From: Viresh Kumar <[email protected]>
> Sent: Wednesday, May 23, 2018 14:31
> To: Ilia Lin <[email protected]>
> Cc: Sudeep Holla <[email protected]>; Viresh Kumar
> <[email protected]>; Nishanth Menon <[email protected]>; Stephen Boyd
> <[email protected]>; Rob Herring <[email protected]>; Mark Rutland
> <[email protected]>; Rafael J. Wysocki <[email protected]>; linux-
> [email protected]; [email protected]; Linux Kernel Mailing List
> <[email protected]>
> Subject: Re: [PATCH v10 1/2] cpufreq: Add Kryo CPU scaling driver
>
> On 23 May 2018 at 16:36, <[email protected]> wrote:
> >
> >
> >> -----Original Message-----
> >> From: Sudeep Holla <[email protected]>
> >> Sent: Wednesday, May 23, 2018 13:40
> >> To: Ilia Lin <[email protected]>; [email protected]; [email protected];
> >> [email protected]; [email protected]; [email protected];
> >> [email protected]; [email protected];
> >> [email protected]; [email protected]
> >> Cc: Sudeep Holla <[email protected]>
> >> Subject: Re: [PATCH v10 1/2] cpufreq: Add Kryo CPU scaling driver
> >>
> >>
> >>
> >> On 23/05/18 10:40, Ilia Lin wrote:
> >> > In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO
> >> > processors, the CPU frequency subset and voltage value of each OPP
> >> > varies based on the silicon variant in use. Qualcomm Process
> >> > Voltage Scaling Tables defines the voltage and frequency value
> >> > based on the msm-id in SMEM and speedbin blown in the efuse
> combination.
> >> > The qcom-cpufreq-kryo driver reads the msm-id and efuse value from
> >> > the SoC to provide the OPP framework with required information.
> >> > This is used to determine the voltage and frequency value for each
> >> > OPP of
> >> > operating-points-v2 table when it is parsed by the OPP framework.
> >> >
> >> > Signed-off-by: Ilia Lin <[email protected]>
> >>
> >> [...]
> >>
> >> > + pdev = platform_device_register_simple("cpufreq-dt", -1, NULL, 0);
> >> > + if (!IS_ERR(pdev))
> >> > + return 0;
> >> > +
> >> > + ret = PTR_ERR(pdev);
> >> > + dev_err(cpu_dev, "Failed to register platform device\n");
> >> > +
> >> > +free_opp:
> >> > + for_each_possible_cpu(cpu) {
> >> > + if (IS_ERR_OR_NULL(opp_tables[cpu]))
> >> > + break;
> >> > + dev_pm_opp_put_supported_hw(opp_tables[cpu]);
> >> > + }
> >> > +free_np:
> >> > + of_node_put(np);
> >> > +
> >> > + return ret;
> >> > +}
> >> > +late_initcall(qcom_cpufreq_kryo_driver_init);
> >>
> >> Any particular reason why this *has* to be late initcall ?
> >> Please change it to module_initcall otherwise.
> >
> > The purpose is to give the cpufreq-dt the time to register the driver and
> only then my driver will add the platform device.
>
> That isn't required, the device and its driver can be registered in any order.
You are right. I already checked that in the code...
However, with module_init() the driver fails on reading the nvmem.
On 23 May 2018 at 17:04, <[email protected]> wrote:
> You are right. I already checked that in the code...
> However, with module_init() the driver fails on reading the nvmem.
And why is it failing ?
The nvmem will return EPROBE_DEFER, and so will my driver's init. But then no one will call the init again.
> -----Original Message-----
> From: Viresh Kumar <[email protected]>
> Sent: Wednesday, May 23, 2018 14:46
> To: Ilia Lin <[email protected]>
> Cc: Sudeep Holla <[email protected]>; Viresh Kumar
> <[email protected]>; Nishanth Menon <[email protected]>; Stephen Boyd
> <[email protected]>; Rob Herring <[email protected]>; Mark Rutland
> <[email protected]>; Rafael J. Wysocki <[email protected]>; linux-
> [email protected]; [email protected]; Linux Kernel Mailing List
> <[email protected]>
> Subject: Re: [PATCH v10 1/2] cpufreq: Add Kryo CPU scaling driver
>
> On 23 May 2018 at 17:04, <[email protected]> wrote:
> > You are right. I already checked that in the code...
> > However, with module_init() the driver fails on reading the nvmem.
>
> And why is it failing ?
On 23 May 2018 at 17:17, <[email protected]> wrote:
> The nvmem will return EPROBE_DEFER, and so will my driver's init. But then no one will call the init again.
So even your driver needs to be registered as a platform driver then
and you can create its device
from the init function, and add a comment on why you create the
platform device in the driver itself.
--
viresh