Hi All,
arm64: dts: ti: k3-j7200: add dma and mcu cpsw nodes
This series adds DT nodes for TI J7200 SoC
- INTR/INTA, Ringacc and UDMA nodes for Main and MCU NAVSS, which are compatible
with J721E Soc, to enable DMA support
- MCU CPSW2g DT nodes to enable networking
This series depends on:
- [PATCH v2 0/4] arm64: Initial support for Texas Instrument's J7200 Platform [1]
from: Lokesh Vutla <[email protected]>
- [PATCH] soc: ti: k3-socinfo: Add entry for J7200 [2]
from: Peter Ujfalusi <[email protected]>
[1] https://lore.kernel.org/linux-arm-kernel/[email protected]/T/#m141ae4d0dd818518c00c81806d689983d6e832e6
[2] https://lore.kernel.org/patchwork/patch/1283230/
Grygorii Strashko (3):
arm64: dts: ti: k3-j7200-main: add main navss cpts node
arm64: dts: ti: k3-j7200-mcu: add mcu cpsw nuss node
arm64: dts: ti: k3-j7200-common-proc-board: add mcu cpsw nuss pinmux
and phy defs
Peter Ujfalusi (1):
arm64: dts: ti: k3-j7200: add DMA support
.../dts/ti/k3-j7200-common-proc-board.dts | 45 +++++++
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 73 +++++++++++
.../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 118 ++++++++++++++++++
3 files changed, 236 insertions(+)
--
2.17.1
From: Peter Ujfalusi <[email protected]>
Add the intr, inta, ringacc and udmap nodes for main and mcu NAVSS.
Signed-off-by: Peter Ujfalusi <[email protected]>
Signed-off-by: Grygorii Strashko <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 61 +++++++++++++++++++
.../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 44 +++++++++++++
2 files changed, 105 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index 70c8f7e941fb..cc4ff380a7bc 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -45,6 +45,31 @@
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x00 0x30000000 0x00 0x30000000 0x00 0x0c400000>;
+ ti,sci-dev-id = <199>;
+
+ main_navss_intr: interrupt-controller1 {
+ compatible = "ti,sci-intr";
+ ti,intr-trigger-type = <4>;
+ interrupt-controller;
+ interrupt-parent = <&gic500>;
+ #interrupt-cells = <1>;
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <213>;
+ ti,interrupt-ranges = <0 64 64>,
+ <64 448 64>,
+ <128 672 64>;
+ };
+
+ main_udmass_inta: interrupt-controller@33d00000 {
+ compatible = "ti,sci-inta";
+ reg = <0x0 0x33d00000 0x0 0x100000>;
+ interrupt-controller;
+ interrupt-parent = <&main_navss_intr>;
+ msi-controller;
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <209>;
+ ti,interrupt-ranges = <0 0 256>;
+ };
secure_proxy_main: mailbox@32c00000 {
compatible = "ti,am654-secure-proxy";
@@ -56,6 +81,42 @@
interrupt-names = "rx_011";
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
};
+
+ main_ringacc: ringacc@3c000000 {
+ compatible = "ti,am654-navss-ringacc";
+ reg = <0x0 0x3c000000 0x0 0x400000>,
+ <0x0 0x38000000 0x0 0x400000>,
+ <0x0 0x31120000 0x0 0x100>,
+ <0x0 0x33000000 0x0 0x40000>;
+ reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target";
+ ti,num-rings = <1024>;
+ ti,sci-rm-range-gp-rings = <0x1>; /* GP ring range */
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <211>;
+ msi-parent = <&main_udmass_inta>;
+ };
+
+ main_udmap: dma-controller@31150000 {
+ compatible = "ti,j721e-navss-main-udmap";
+ reg = <0x0 0x31150000 0x0 0x100>,
+ <0x0 0x34000000 0x0 0x100000>,
+ <0x0 0x35000000 0x0 0x100000>;
+ reg-names = "gcfg", "rchanrt", "tchanrt";
+ msi-parent = <&main_udmass_inta>;
+ #dma-cells = <1>;
+
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <212>;
+ ti,ringacc = <&main_ringacc>;
+
+ ti,sci-rm-range-tchan = <0x0d>, /* TX_CHAN */
+ <0x0f>, /* TX_HCHAN */
+ <0x10>; /* TX_UHCHAN */
+ ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */
+ <0x0b>, /* RX_HCHAN */
+ <0x0c>; /* RX_UHCHAN */
+ ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
+ };
};
main_pmx0: pinmux@11c000 {
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index 670e4c7cd9fe..9ecb7e0c9cf7 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -81,4 +81,48 @@
clocks = <&k3_clks 149 2>;
clock-names = "fclk";
};
+
+ cbass_mcu_navss: navss@28380000 {
+ compatible = "simple-mfd";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ dma-coherent;
+ dma-ranges;
+ ti,sci-dev-id = <232>;
+
+ mcu_ringacc: ringacc@2b800000 {
+ compatible = "ti,am654-navss-ringacc";
+ reg = <0x0 0x2b800000 0x0 0x400000>,
+ <0x0 0x2b000000 0x0 0x400000>,
+ <0x0 0x28590000 0x0 0x100>,
+ <0x0 0x2a500000 0x0 0x40000>;
+ reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target";
+ ti,num-rings = <286>;
+ ti,sci-rm-range-gp-rings = <0x1>; /* GP ring range */
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <235>;
+ msi-parent = <&main_udmass_inta>;
+ };
+
+ mcu_udmap: dma-controller@285c0000 {
+ compatible = "ti,j721e-navss-mcu-udmap";
+ reg = <0x0 0x285c0000 0x0 0x100>,
+ <0x0 0x2a800000 0x0 0x40000>,
+ <0x0 0x2aa00000 0x0 0x40000>;
+ reg-names = "gcfg", "rchanrt", "tchanrt";
+ msi-parent = <&main_udmass_inta>;
+ #dma-cells = <1>;
+
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <236>;
+ ti,ringacc = <&mcu_ringacc>;
+
+ ti,sci-rm-range-tchan = <0x0d>, /* TX_CHAN */
+ <0x0f>; /* TX_HCHAN */
+ ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */
+ <0x0b>; /* RX_HCHAN */
+ ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
+ };
+ };
};
--
2.17.1
The TI j7200 EVM base board has TI DP83867 PHY connected to external CPSW
NUSS Port 1 in rgmii-rxid mode.
Hence, add pinmux and Ethernet PHY configuration for TI j7200 SoC MCU
Gigabit Ethernet two ports Switch subsystem (CPSW NUSS).
Signed-off-by: Grygorii Strashko <[email protected]>
---
.../dts/ti/k3-j7200-common-proc-board.dts | 45 +++++++++++++++++++
1 file changed, 45 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index e27069317c4e..52bde66930d1 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -6,6 +6,7 @@
/dts-v1/;
#include "k3-j7200-som-p0.dtsi"
+#include <dt-bindings/net/ti-dp83867.h>
/ {
chosen {
@@ -14,6 +15,32 @@
};
};
+&wkup_pmx0 {
+ mcu_cpsw_pins_default: mcu_cpsw_pins_default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
+ J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
+ J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
+ J721E_WKUP_IOPAD(0x0074, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
+ J721E_WKUP_IOPAD(0x0078, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
+ J721E_WKUP_IOPAD(0x007c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
+ J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
+ J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
+ J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
+ J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
+ J721E_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* MCU_RGMII1_TXC */
+ J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
+ >;
+ };
+
+ mcu_mdio_pins_default: mcu_mdio1_pins_default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
+ J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
+ >;
+ };
+};
+
&wkup_uart0 {
/* Wakeup UART is used by System firmware */
status = "disabled";
@@ -62,3 +89,21 @@
/* UART not brought out */
status = "disabled";
};
+
+&mcu_cpsw {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
+};
+
+&davinci_mdio {
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ };
+};
+
+&cpsw_port1 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&phy0>;
+};
--
2.17.1
Add DT node for Main NAVSS CPTS module.
Signed-off-by: Grygorii Strashko <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index cc4ff380a7bc..822c062e25c8 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -117,6 +117,18 @@
<0x0c>; /* RX_UHCHAN */
ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
};
+
+ cpts@310d0000 {
+ compatible = "ti,j721e-cpts";
+ reg = <0x0 0x310d0000 0x0 0x400>;
+ reg-names = "cpts";
+ clocks = <&k3_clks 201 1>;
+ clock-names = "cpts";
+ interrupts-extended = <&main_navss_intr 391>;
+ interrupt-names = "cpts";
+ ti,cpts-periodic-outputs = <6>;
+ ti,cpts-ext-ts-inputs = <8>;
+ };
};
main_pmx0: pinmux@11c000 {
--
2.17.1
Add DT node for The TI j7200 MCU SoC Gigabit Ethernet two ports Switch
subsystem (MCU CPSW NUSS).
Signed-off-by: Grygorii Strashko <[email protected]>
---
.../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 74 +++++++++++++++++++
1 file changed, 74 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index 9ecb7e0c9cf7..06cd6a80a499 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -34,6 +34,20 @@
};
};
+ mcu_conf: syscon@40f00000 {
+ compatible = "syscon", "simple-mfd";
+ reg = <0x0 0x40f00000 0x0 0x20000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0x40f00000 0x20000>;
+
+ phy_gmii_sel: phy@4040 {
+ compatible = "ti,am654-phy-gmii-sel";
+ reg = <0x4040 0x4>;
+ #phy-cells = <1>;
+ };
+ };
+
chipid@43000014 {
compatible = "ti,am654-chipid";
reg = <0x0 0x43000014 0x0 0x4>;
@@ -125,4 +139,64 @@
ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
};
};
+
+ mcu_cpsw: ethernet@46000000 {
+ compatible = "ti,j721e-cpsw-nuss";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ reg = <0x0 0x46000000 0x0 0x200000>;
+ reg-names = "cpsw_nuss";
+ ranges = <0x0 0x0 0x0 0x46000000 0x0 0x200000>;
+ dma-coherent;
+ clocks = <&k3_clks 18 21>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 18 TI_SCI_PD_EXCLUSIVE>;
+
+ dmas = <&mcu_udmap 0xf000>,
+ <&mcu_udmap 0xf001>,
+ <&mcu_udmap 0xf002>,
+ <&mcu_udmap 0xf003>,
+ <&mcu_udmap 0xf004>,
+ <&mcu_udmap 0xf005>,
+ <&mcu_udmap 0xf006>,
+ <&mcu_udmap 0xf007>,
+ <&mcu_udmap 0x7000>;
+ dma-names = "tx0", "tx1", "tx2", "tx3",
+ "tx4", "tx5", "tx6", "tx7",
+ "rx";
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpsw_port1: port@1 {
+ reg = <1>;
+ ti,mac-only;
+ label = "port1";
+ ti,syscon-efuse = <&mcu_conf 0x200>;
+ phys = <&phy_gmii_sel 1>;
+ };
+ };
+
+ davinci_mdio: mdio@f00 {
+ compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+ reg = <0x0 0xf00 0x0 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&k3_clks 18 21>;
+ clock-names = "fck";
+ bus_freq = <1000000>;
+ };
+
+ cpts@3d000 {
+ compatible = "ti,am65-cpts";
+ reg = <0x0 0x3d000 0x0 0x400>;
+ clocks = <&k3_clks 18 2>;
+ clock-names = "cpts";
+ interrupts-extended = <&gic500 GIC_SPI 858 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cpts";
+ ti,cpts-ext-ts-inputs = <4>;
+ ti,cpts-periodic-outputs = <2>;
+ };
+ };
};
--
2.17.1
Hi Grygorii,
On 05/09/2020 2.38, Grygorii Strashko wrote:
> Hi All,
>
> arm64: dts: ti: k3-j7200: add dma and mcu cpsw nodes
>
> This series adds DT nodes for TI J7200 SoC
> - INTR/INTA, Ringacc and UDMA nodes for Main and MCU NAVSS, which are compatible
> with J721E Soc, to enable DMA support
> - MCU CPSW2g DT nodes to enable networking
>
> This series depends on:
> - [PATCH v2 0/4] arm64: Initial support for Texas Instrument's J7200 Platform [1]
> from: Lokesh Vutla <[email protected]>
> - [PATCH] soc: ti: k3-socinfo: Add entry for J7200 [2]
> from: Peter Ujfalusi <[email protected]>
you also need to pick:
[PATCH] dmaengine: ti: k3-udma: Use soc_device_match() for SoC dependent parameters [3]
>
> [1] https://lore.kernel.org/linux-arm-kernel/[email protected]/T/#m141ae4d0dd818518c00c81806d689983d6e832e6
> [2] https://lore.kernel.org/patchwork/patch/1283230/
[3] https://lore.kernel.org/lkml/[email protected]/
>
> Grygorii Strashko (3):
> arm64: dts: ti: k3-j7200-main: add main navss cpts node
> arm64: dts: ti: k3-j7200-mcu: add mcu cpsw nuss node
> arm64: dts: ti: k3-j7200-common-proc-board: add mcu cpsw nuss pinmux
> and phy defs
>
> Peter Ujfalusi (1):
> arm64: dts: ti: k3-j7200: add DMA support
>
> .../dts/ti/k3-j7200-common-proc-board.dts | 45 +++++++
> arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 73 +++++++++++
> .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 118 ++++++++++++++++++
> 3 files changed, 236 insertions(+)
>
- Péter
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki