When auto calibration timeouts, calibration is disabled and fail-safe
drive strength values are programmed based on the signal voltage.
Different fail-safe drive strength values based on voltage are
applicable only for SoCs supporting 3V3 and 1V8 pad controls.
So, this patch avoids reading these properties from the device tree
for SoCs not using pad controls and the warning of missing properties
will not show up on these SoC platforms.
Signed-off-by: Sowjanya Komatineni <[email protected]>
---
drivers/mmc/host/sdhci-tegra.c | 57 ++++++++++++++++++++++++------------------
1 file changed, 33 insertions(+), 24 deletions(-)
diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
index 3e2c510..141b49b 100644
--- a/drivers/mmc/host/sdhci-tegra.c
+++ b/drivers/mmc/host/sdhci-tegra.c
@@ -605,6 +605,39 @@ static void tegra_sdhci_parse_pad_autocal_dt(struct sdhci_host *host)
autocal->pull_down_1v8 = 0;
err = device_property_read_u32(host->mmc->parent,
+ "nvidia,pad-autocal-pull-up-offset-sdr104",
+ &autocal->pull_up_sdr104);
+ if (err)
+ autocal->pull_up_sdr104 = autocal->pull_up_1v8;
+
+ err = device_property_read_u32(host->mmc->parent,
+ "nvidia,pad-autocal-pull-down-offset-sdr104",
+ &autocal->pull_down_sdr104);
+ if (err)
+ autocal->pull_down_sdr104 = autocal->pull_down_1v8;
+
+ err = device_property_read_u32(host->mmc->parent,
+ "nvidia,pad-autocal-pull-up-offset-hs400",
+ &autocal->pull_up_hs400);
+ if (err)
+ autocal->pull_up_hs400 = autocal->pull_up_1v8;
+
+ err = device_property_read_u32(host->mmc->parent,
+ "nvidia,pad-autocal-pull-down-offset-hs400",
+ &autocal->pull_down_hs400);
+ if (err)
+ autocal->pull_down_hs400 = autocal->pull_down_1v8;
+
+ /*
+ * Different fail-safe drive strength values based on the signaling
+ * voltage are applicable for SoCs supporting 3V3 and 1V8 pad controls.
+ * So, avoid reading below device tree properies for SoCs that don't
+ * have NVQUIRK_NEEDS_PAD_CONTROL.
+ */
+ if (!(tegra_host->soc_data->nvquirks & NVQUIRK_NEEDS_PAD_CONTROL))
+ return;
+
+ err = device_property_read_u32(host->mmc->parent,
"nvidia,pad-autocal-pull-up-offset-3v3-timeout",
&autocal->pull_up_3v3_timeout);
if (err) {
@@ -647,30 +680,6 @@ static void tegra_sdhci_parse_pad_autocal_dt(struct sdhci_host *host)
mmc_hostname(host->mmc));
autocal->pull_down_1v8_timeout = 0;
}
-
- err = device_property_read_u32(host->mmc->parent,
- "nvidia,pad-autocal-pull-up-offset-sdr104",
- &autocal->pull_up_sdr104);
- if (err)
- autocal->pull_up_sdr104 = autocal->pull_up_1v8;
-
- err = device_property_read_u32(host->mmc->parent,
- "nvidia,pad-autocal-pull-down-offset-sdr104",
- &autocal->pull_down_sdr104);
- if (err)
- autocal->pull_down_sdr104 = autocal->pull_down_1v8;
-
- err = device_property_read_u32(host->mmc->parent,
- "nvidia,pad-autocal-pull-up-offset-hs400",
- &autocal->pull_up_hs400);
- if (err)
- autocal->pull_up_hs400 = autocal->pull_up_1v8;
-
- err = device_property_read_u32(host->mmc->parent,
- "nvidia,pad-autocal-pull-down-offset-hs400",
- &autocal->pull_down_hs400);
- if (err)
- autocal->pull_down_hs400 = autocal->pull_down_1v8;
}
static void tegra_sdhci_request(struct mmc_host *mmc, struct mmc_request *mrq)
--
2.7.4
20.05.2020 23:08, Sowjanya Komatineni пишет:
> When auto calibration timeouts, calibration is disabled and fail-safe
> drive strength values are programmed based on the signal voltage.
>
> Different fail-safe drive strength values based on voltage are
> applicable only for SoCs supporting 3V3 and 1V8 pad controls.
>
> So, this patch avoids reading these properties from the device tree
> for SoCs not using pad controls and the warning of missing properties
> will not show up on these SoC platforms.
>
> Signed-off-by: Sowjanya Komatineni <[email protected]>
> ---
> drivers/mmc/host/sdhci-tegra.c | 57 ++++++++++++++++++++++++------------------
> 1 file changed, 33 insertions(+), 24 deletions(-)
Hello Sowjanya,
Thank you for the patch.
Tested-by: Dmitry Osipenko <[email protected]>
20.05.2020 23:08, Sowjanya Komatineni пишет:
> When auto calibration timeouts, calibration is disabled and fail-safe
> drive strength values are programmed based on the signal voltage.
>
> Different fail-safe drive strength values based on voltage are
> applicable only for SoCs supporting 3V3 and 1V8 pad controls.
>
> So, this patch avoids reading these properties from the device tree
> for SoCs not using pad controls and the warning of missing properties
> will not show up on these SoC platforms.
>
> Signed-off-by: Sowjanya Komatineni <[email protected]>
> ---
> drivers/mmc/host/sdhci-tegra.c | 57 ++++++++++++++++++++++++------------------
> 1 file changed, 33 insertions(+), 24 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
> index 3e2c510..141b49b 100644
> --- a/drivers/mmc/host/sdhci-tegra.c
> +++ b/drivers/mmc/host/sdhci-tegra.c
> @@ -605,6 +605,39 @@ static void tegra_sdhci_parse_pad_autocal_dt(struct sdhci_host *host)
> autocal->pull_down_1v8 = 0;
>
> err = device_property_read_u32(host->mmc->parent,
> + "nvidia,pad-autocal-pull-up-offset-sdr104",
> + &autocal->pull_up_sdr104);
> + if (err)
> + autocal->pull_up_sdr104 = autocal->pull_up_1v8;
> +
> + err = device_property_read_u32(host->mmc->parent,
> + "nvidia,pad-autocal-pull-down-offset-sdr104",
> + &autocal->pull_down_sdr104);
> + if (err)
> + autocal->pull_down_sdr104 = autocal->pull_down_1v8;
> +
> + err = device_property_read_u32(host->mmc->parent,
> + "nvidia,pad-autocal-pull-up-offset-hs400",
> + &autocal->pull_up_hs400);
> + if (err)
> + autocal->pull_up_hs400 = autocal->pull_up_1v8;
> +
> + err = device_property_read_u32(host->mmc->parent,
> + "nvidia,pad-autocal-pull-down-offset-hs400",
> + &autocal->pull_down_hs400);
> + if (err)
> + autocal->pull_down_hs400 = autocal->pull_down_1v8;
> +
> + /*
> + * Different fail-safe drive strength values based on the signaling
> + * voltage are applicable for SoCs supporting 3V3 and 1V8 pad controls.
> + * So, avoid reading below device tree properies for SoCs that don't
typo s/properies/properties/ ^^^
> + * have NVQUIRK_NEEDS_PAD_CONTROL.
> + */
...
On Wed, May 20, 2020 at 01:08:57PM -0700, Sowjanya Komatineni wrote:
> When auto calibration timeouts, calibration is disabled and fail-safe
> drive strength values are programmed based on the signal voltage.
>
> Different fail-safe drive strength values based on voltage are
> applicable only for SoCs supporting 3V3 and 1V8 pad controls.
>
> So, this patch avoids reading these properties from the device tree
> for SoCs not using pad controls and the warning of missing properties
> will not show up on these SoC platforms.
>
> Signed-off-by: Sowjanya Komatineni <[email protected]>
> ---
> drivers/mmc/host/sdhci-tegra.c | 57 ++++++++++++++++++++++++------------------
> 1 file changed, 33 insertions(+), 24 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
> index 3e2c510..141b49b 100644
> --- a/drivers/mmc/host/sdhci-tegra.c
> +++ b/drivers/mmc/host/sdhci-tegra.c
> @@ -605,6 +605,39 @@ static void tegra_sdhci_parse_pad_autocal_dt(struct sdhci_host *host)
> autocal->pull_down_1v8 = 0;
>
> err = device_property_read_u32(host->mmc->parent,
> + "nvidia,pad-autocal-pull-up-offset-sdr104",
> + &autocal->pull_up_sdr104);
> + if (err)
> + autocal->pull_up_sdr104 = autocal->pull_up_1v8;
> +
> + err = device_property_read_u32(host->mmc->parent,
> + "nvidia,pad-autocal-pull-down-offset-sdr104",
> + &autocal->pull_down_sdr104);
> + if (err)
> + autocal->pull_down_sdr104 = autocal->pull_down_1v8;
> +
> + err = device_property_read_u32(host->mmc->parent,
> + "nvidia,pad-autocal-pull-up-offset-hs400",
> + &autocal->pull_up_hs400);
> + if (err)
> + autocal->pull_up_hs400 = autocal->pull_up_1v8;
> +
> + err = device_property_read_u32(host->mmc->parent,
> + "nvidia,pad-autocal-pull-down-offset-hs400",
> + &autocal->pull_down_hs400);
> + if (err)
> + autocal->pull_down_hs400 = autocal->pull_down_1v8;
> +
> + /*
> + * Different fail-safe drive strength values based on the signaling
> + * voltage are applicable for SoCs supporting 3V3 and 1V8 pad controls.
> + * So, avoid reading below device tree properies for SoCs that don't
> + * have NVQUIRK_NEEDS_PAD_CONTROL.
> + */
> + if (!(tegra_host->soc_data->nvquirks & NVQUIRK_NEEDS_PAD_CONTROL))
> + return;
Hm... so what exactly is the difference between NVQUIRK_HAS_PADCALIB? I
think Tegra30 will also end up calling tegra_sdhci_set_padctrl(), but it
will then write the default (0) value for these drive strength. Is that
okay?
Thierry
22.05.2020 15:26, Thierry Reding пишет:
> On Wed, May 20, 2020 at 01:08:57PM -0700, Sowjanya Komatineni wrote:
>> When auto calibration timeouts, calibration is disabled and fail-safe
>> drive strength values are programmed based on the signal voltage.
>>
>> Different fail-safe drive strength values based on voltage are
>> applicable only for SoCs supporting 3V3 and 1V8 pad controls.
>>
>> So, this patch avoids reading these properties from the device tree
>> for SoCs not using pad controls and the warning of missing properties
>> will not show up on these SoC platforms.
>>
>> Signed-off-by: Sowjanya Komatineni <[email protected]>
>> ---
>> drivers/mmc/host/sdhci-tegra.c | 57 ++++++++++++++++++++++++------------------
>> 1 file changed, 33 insertions(+), 24 deletions(-)
>>
>> diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
>> index 3e2c510..141b49b 100644
>> --- a/drivers/mmc/host/sdhci-tegra.c
>> +++ b/drivers/mmc/host/sdhci-tegra.c
>> @@ -605,6 +605,39 @@ static void tegra_sdhci_parse_pad_autocal_dt(struct sdhci_host *host)
>> autocal->pull_down_1v8 = 0;
>>
>> err = device_property_read_u32(host->mmc->parent,
>> + "nvidia,pad-autocal-pull-up-offset-sdr104",
>> + &autocal->pull_up_sdr104);
>> + if (err)
>> + autocal->pull_up_sdr104 = autocal->pull_up_1v8;
>> +
>> + err = device_property_read_u32(host->mmc->parent,
>> + "nvidia,pad-autocal-pull-down-offset-sdr104",
>> + &autocal->pull_down_sdr104);
>> + if (err)
>> + autocal->pull_down_sdr104 = autocal->pull_down_1v8;
>> +
>> + err = device_property_read_u32(host->mmc->parent,
>> + "nvidia,pad-autocal-pull-up-offset-hs400",
>> + &autocal->pull_up_hs400);
>> + if (err)
>> + autocal->pull_up_hs400 = autocal->pull_up_1v8;
>> +
>> + err = device_property_read_u32(host->mmc->parent,
>> + "nvidia,pad-autocal-pull-down-offset-hs400",
>> + &autocal->pull_down_hs400);
>> + if (err)
>> + autocal->pull_down_hs400 = autocal->pull_down_1v8;
>> +
>> + /*
>> + * Different fail-safe drive strength values based on the signaling
>> + * voltage are applicable for SoCs supporting 3V3 and 1V8 pad controls.
>> + * So, avoid reading below device tree properies for SoCs that don't
>> + * have NVQUIRK_NEEDS_PAD_CONTROL.
>> + */
>> + if (!(tegra_host->soc_data->nvquirks & NVQUIRK_NEEDS_PAD_CONTROL))
>> + return;
>
> Hm... so what exactly is the difference between NVQUIRK_HAS_PADCALIB? I
> think Tegra30 will also end up calling tegra_sdhci_set_padctrl(), but it
> will then write the default (0) value for these drive strength. Is that
> okay?
It won't write 0, but skip the writing if values are 0. Technically T30+
supports the customized strengths, but I'm not sure whether it was ever
tested and whether it's really needed. I think Sowjanya said before that
the default values are always okay for older SoCs.
On Fri, May 22, 2020 at 03:42:18PM +0300, Dmitry Osipenko wrote:
> 22.05.2020 15:26, Thierry Reding пишет:
> > On Wed, May 20, 2020 at 01:08:57PM -0700, Sowjanya Komatineni wrote:
> >> When auto calibration timeouts, calibration is disabled and fail-safe
> >> drive strength values are programmed based on the signal voltage.
> >>
> >> Different fail-safe drive strength values based on voltage are
> >> applicable only for SoCs supporting 3V3 and 1V8 pad controls.
> >>
> >> So, this patch avoids reading these properties from the device tree
> >> for SoCs not using pad controls and the warning of missing properties
> >> will not show up on these SoC platforms.
> >>
> >> Signed-off-by: Sowjanya Komatineni <[email protected]>
> >> ---
> >> drivers/mmc/host/sdhci-tegra.c | 57 ++++++++++++++++++++++++------------------
> >> 1 file changed, 33 insertions(+), 24 deletions(-)
> >>
> >> diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
> >> index 3e2c510..141b49b 100644
> >> --- a/drivers/mmc/host/sdhci-tegra.c
> >> +++ b/drivers/mmc/host/sdhci-tegra.c
> >> @@ -605,6 +605,39 @@ static void tegra_sdhci_parse_pad_autocal_dt(struct sdhci_host *host)
> >> autocal->pull_down_1v8 = 0;
> >>
> >> err = device_property_read_u32(host->mmc->parent,
> >> + "nvidia,pad-autocal-pull-up-offset-sdr104",
> >> + &autocal->pull_up_sdr104);
> >> + if (err)
> >> + autocal->pull_up_sdr104 = autocal->pull_up_1v8;
> >> +
> >> + err = device_property_read_u32(host->mmc->parent,
> >> + "nvidia,pad-autocal-pull-down-offset-sdr104",
> >> + &autocal->pull_down_sdr104);
> >> + if (err)
> >> + autocal->pull_down_sdr104 = autocal->pull_down_1v8;
> >> +
> >> + err = device_property_read_u32(host->mmc->parent,
> >> + "nvidia,pad-autocal-pull-up-offset-hs400",
> >> + &autocal->pull_up_hs400);
> >> + if (err)
> >> + autocal->pull_up_hs400 = autocal->pull_up_1v8;
> >> +
> >> + err = device_property_read_u32(host->mmc->parent,
> >> + "nvidia,pad-autocal-pull-down-offset-hs400",
> >> + &autocal->pull_down_hs400);
> >> + if (err)
> >> + autocal->pull_down_hs400 = autocal->pull_down_1v8;
> >> +
> >> + /*
> >> + * Different fail-safe drive strength values based on the signaling
> >> + * voltage are applicable for SoCs supporting 3V3 and 1V8 pad controls.
> >> + * So, avoid reading below device tree properies for SoCs that don't
> >> + * have NVQUIRK_NEEDS_PAD_CONTROL.
> >> + */
> >> + if (!(tegra_host->soc_data->nvquirks & NVQUIRK_NEEDS_PAD_CONTROL))
> >> + return;
> >
> > Hm... so what exactly is the difference between NVQUIRK_HAS_PADCALIB? I
> > think Tegra30 will also end up calling tegra_sdhci_set_padctrl(), but it
> > will then write the default (0) value for these drive strength. Is that
> > okay?
>
> It won't write 0, but skip the writing if values are 0. Technically T30+
> supports the customized strengths, but I'm not sure whether it was ever
> tested and whether it's really needed. I think Sowjanya said before that
> the default values are always okay for older SoCs.
Alright then, in that case:
Acked-by: Thierry Reding <[email protected]>
On 5/22/20 5:52 AM, Thierry Reding wrote:
> On Fri, May 22, 2020 at 03:42:18PM +0300, Dmitry Osipenko wrote:
>> 22.05.2020 15:26, Thierry Reding пишет:
>>> On Wed, May 20, 2020 at 01:08:57PM -0700, Sowjanya Komatineni wrote:
>>>> When auto calibration timeouts, calibration is disabled and fail-safe
>>>> drive strength values are programmed based on the signal voltage.
>>>>
>>>> Different fail-safe drive strength values based on voltage are
>>>> applicable only for SoCs supporting 3V3 and 1V8 pad controls.
>>>>
>>>> So, this patch avoids reading these properties from the device tree
>>>> for SoCs not using pad controls and the warning of missing properties
>>>> will not show up on these SoC platforms.
>>>>
>>>> Signed-off-by: Sowjanya Komatineni <[email protected]>
>>>> ---
>>>> drivers/mmc/host/sdhci-tegra.c | 57 ++++++++++++++++++++++++------------------
>>>> 1 file changed, 33 insertions(+), 24 deletions(-)
>>>>
>>>> diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
>>>> index 3e2c510..141b49b 100644
>>>> --- a/drivers/mmc/host/sdhci-tegra.c
>>>> +++ b/drivers/mmc/host/sdhci-tegra.c
>>>> @@ -605,6 +605,39 @@ static void tegra_sdhci_parse_pad_autocal_dt(struct sdhci_host *host)
>>>> autocal->pull_down_1v8 = 0;
>>>>
>>>> err = device_property_read_u32(host->mmc->parent,
>>>> + "nvidia,pad-autocal-pull-up-offset-sdr104",
>>>> + &autocal->pull_up_sdr104);
>>>> + if (err)
>>>> + autocal->pull_up_sdr104 = autocal->pull_up_1v8;
>>>> +
>>>> + err = device_property_read_u32(host->mmc->parent,
>>>> + "nvidia,pad-autocal-pull-down-offset-sdr104",
>>>> + &autocal->pull_down_sdr104);
>>>> + if (err)
>>>> + autocal->pull_down_sdr104 = autocal->pull_down_1v8;
>>>> +
>>>> + err = device_property_read_u32(host->mmc->parent,
>>>> + "nvidia,pad-autocal-pull-up-offset-hs400",
>>>> + &autocal->pull_up_hs400);
>>>> + if (err)
>>>> + autocal->pull_up_hs400 = autocal->pull_up_1v8;
>>>> +
>>>> + err = device_property_read_u32(host->mmc->parent,
>>>> + "nvidia,pad-autocal-pull-down-offset-hs400",
>>>> + &autocal->pull_down_hs400);
>>>> + if (err)
>>>> + autocal->pull_down_hs400 = autocal->pull_down_1v8;
>>>> +
>>>> + /*
>>>> + * Different fail-safe drive strength values based on the signaling
>>>> + * voltage are applicable for SoCs supporting 3V3 and 1V8 pad controls.
>>>> + * So, avoid reading below device tree properies for SoCs that don't
>>>> + * have NVQUIRK_NEEDS_PAD_CONTROL.
>>>> + */
>>>> + if (!(tegra_host->soc_data->nvquirks & NVQUIRK_NEEDS_PAD_CONTROL))
>>>> + return;
>>> Hm... so what exactly is the difference between NVQUIRK_HAS_PADCALIB? I
>>> think Tegra30 will also end up calling tegra_sdhci_set_padctrl(), but it
>>> will then write the default (0) value for these drive strength. Is that
>>> okay?
Yes separate 3v3 and 1v8 drive strengths are for Tegra210/184/194 where
they have separate pad controls.
T30 also has auto calibration enabled but don't need to use these
properties as they don't have separate default drive strengths based on
signaling.
Same default drive strengths set by boot loader/default pinmux will hold
good.
>> It won't write 0, but skip the writing if values are 0. Technically T30+
>> supports the customized strengths, but I'm not sure whether it was ever
>> tested and whether it's really needed. I think Sowjanya said before that
>> the default values are always okay for older SoCs.
> Alright then, in that case:
>
> Acked-by: Thierry Reding <[email protected]>
On 20/05/20 11:08 pm, Sowjanya Komatineni wrote:
> When auto calibration timeouts, calibration is disabled and fail-safe
> drive strength values are programmed based on the signal voltage.
>
> Different fail-safe drive strength values based on voltage are
> applicable only for SoCs supporting 3V3 and 1V8 pad controls.
>
> So, this patch avoids reading these properties from the device tree
> for SoCs not using pad controls and the warning of missing properties
> will not show up on these SoC platforms.
>
> Signed-off-by: Sowjanya Komatineni <[email protected]>
Acked-by: Adrian Hunter <[email protected]>
> ---
> drivers/mmc/host/sdhci-tegra.c | 57 ++++++++++++++++++++++++------------------
> 1 file changed, 33 insertions(+), 24 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
> index 3e2c510..141b49b 100644
> --- a/drivers/mmc/host/sdhci-tegra.c
> +++ b/drivers/mmc/host/sdhci-tegra.c
> @@ -605,6 +605,39 @@ static void tegra_sdhci_parse_pad_autocal_dt(struct sdhci_host *host)
> autocal->pull_down_1v8 = 0;
>
> err = device_property_read_u32(host->mmc->parent,
> + "nvidia,pad-autocal-pull-up-offset-sdr104",
> + &autocal->pull_up_sdr104);
> + if (err)
> + autocal->pull_up_sdr104 = autocal->pull_up_1v8;
> +
> + err = device_property_read_u32(host->mmc->parent,
> + "nvidia,pad-autocal-pull-down-offset-sdr104",
> + &autocal->pull_down_sdr104);
> + if (err)
> + autocal->pull_down_sdr104 = autocal->pull_down_1v8;
> +
> + err = device_property_read_u32(host->mmc->parent,
> + "nvidia,pad-autocal-pull-up-offset-hs400",
> + &autocal->pull_up_hs400);
> + if (err)
> + autocal->pull_up_hs400 = autocal->pull_up_1v8;
> +
> + err = device_property_read_u32(host->mmc->parent,
> + "nvidia,pad-autocal-pull-down-offset-hs400",
> + &autocal->pull_down_hs400);
> + if (err)
> + autocal->pull_down_hs400 = autocal->pull_down_1v8;
> +
> + /*
> + * Different fail-safe drive strength values based on the signaling
> + * voltage are applicable for SoCs supporting 3V3 and 1V8 pad controls.
> + * So, avoid reading below device tree properies for SoCs that don't
> + * have NVQUIRK_NEEDS_PAD_CONTROL.
> + */
> + if (!(tegra_host->soc_data->nvquirks & NVQUIRK_NEEDS_PAD_CONTROL))
> + return;
> +
> + err = device_property_read_u32(host->mmc->parent,
> "nvidia,pad-autocal-pull-up-offset-3v3-timeout",
> &autocal->pull_up_3v3_timeout);
> if (err) {
> @@ -647,30 +680,6 @@ static void tegra_sdhci_parse_pad_autocal_dt(struct sdhci_host *host)
> mmc_hostname(host->mmc));
> autocal->pull_down_1v8_timeout = 0;
> }
> -
> - err = device_property_read_u32(host->mmc->parent,
> - "nvidia,pad-autocal-pull-up-offset-sdr104",
> - &autocal->pull_up_sdr104);
> - if (err)
> - autocal->pull_up_sdr104 = autocal->pull_up_1v8;
> -
> - err = device_property_read_u32(host->mmc->parent,
> - "nvidia,pad-autocal-pull-down-offset-sdr104",
> - &autocal->pull_down_sdr104);
> - if (err)
> - autocal->pull_down_sdr104 = autocal->pull_down_1v8;
> -
> - err = device_property_read_u32(host->mmc->parent,
> - "nvidia,pad-autocal-pull-up-offset-hs400",
> - &autocal->pull_up_hs400);
> - if (err)
> - autocal->pull_up_hs400 = autocal->pull_up_1v8;
> -
> - err = device_property_read_u32(host->mmc->parent,
> - "nvidia,pad-autocal-pull-down-offset-hs400",
> - &autocal->pull_down_hs400);
> - if (err)
> - autocal->pull_down_hs400 = autocal->pull_down_1v8;
> }
>
> static void tegra_sdhci_request(struct mmc_host *mmc, struct mmc_request *mrq)
>
On Wed, 20 May 2020 at 22:09, Sowjanya Komatineni
<[email protected]> wrote:
>
> When auto calibration timeouts, calibration is disabled and fail-safe
> drive strength values are programmed based on the signal voltage.
>
> Different fail-safe drive strength values based on voltage are
> applicable only for SoCs supporting 3V3 and 1V8 pad controls.
>
> So, this patch avoids reading these properties from the device tree
> for SoCs not using pad controls and the warning of missing properties
> will not show up on these SoC platforms.
>
> Signed-off-by: Sowjanya Komatineni <[email protected]>
Applied for next and by fixing the misspelled "properies", thanks!
Kind regards
Uffe
> ---
> drivers/mmc/host/sdhci-tegra.c | 57 ++++++++++++++++++++++++------------------
> 1 file changed, 33 insertions(+), 24 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
> index 3e2c510..141b49b 100644
> --- a/drivers/mmc/host/sdhci-tegra.c
> +++ b/drivers/mmc/host/sdhci-tegra.c
> @@ -605,6 +605,39 @@ static void tegra_sdhci_parse_pad_autocal_dt(struct sdhci_host *host)
> autocal->pull_down_1v8 = 0;
>
> err = device_property_read_u32(host->mmc->parent,
> + "nvidia,pad-autocal-pull-up-offset-sdr104",
> + &autocal->pull_up_sdr104);
> + if (err)
> + autocal->pull_up_sdr104 = autocal->pull_up_1v8;
> +
> + err = device_property_read_u32(host->mmc->parent,
> + "nvidia,pad-autocal-pull-down-offset-sdr104",
> + &autocal->pull_down_sdr104);
> + if (err)
> + autocal->pull_down_sdr104 = autocal->pull_down_1v8;
> +
> + err = device_property_read_u32(host->mmc->parent,
> + "nvidia,pad-autocal-pull-up-offset-hs400",
> + &autocal->pull_up_hs400);
> + if (err)
> + autocal->pull_up_hs400 = autocal->pull_up_1v8;
> +
> + err = device_property_read_u32(host->mmc->parent,
> + "nvidia,pad-autocal-pull-down-offset-hs400",
> + &autocal->pull_down_hs400);
> + if (err)
> + autocal->pull_down_hs400 = autocal->pull_down_1v8;
> +
> + /*
> + * Different fail-safe drive strength values based on the signaling
> + * voltage are applicable for SoCs supporting 3V3 and 1V8 pad controls.
> + * So, avoid reading below device tree properies for SoCs that don't
> + * have NVQUIRK_NEEDS_PAD_CONTROL.
> + */
> + if (!(tegra_host->soc_data->nvquirks & NVQUIRK_NEEDS_PAD_CONTROL))
> + return;
> +
> + err = device_property_read_u32(host->mmc->parent,
> "nvidia,pad-autocal-pull-up-offset-3v3-timeout",
> &autocal->pull_up_3v3_timeout);
> if (err) {
> @@ -647,30 +680,6 @@ static void tegra_sdhci_parse_pad_autocal_dt(struct sdhci_host *host)
> mmc_hostname(host->mmc));
> autocal->pull_down_1v8_timeout = 0;
> }
> -
> - err = device_property_read_u32(host->mmc->parent,
> - "nvidia,pad-autocal-pull-up-offset-sdr104",
> - &autocal->pull_up_sdr104);
> - if (err)
> - autocal->pull_up_sdr104 = autocal->pull_up_1v8;
> -
> - err = device_property_read_u32(host->mmc->parent,
> - "nvidia,pad-autocal-pull-down-offset-sdr104",
> - &autocal->pull_down_sdr104);
> - if (err)
> - autocal->pull_down_sdr104 = autocal->pull_down_1v8;
> -
> - err = device_property_read_u32(host->mmc->parent,
> - "nvidia,pad-autocal-pull-up-offset-hs400",
> - &autocal->pull_up_hs400);
> - if (err)
> - autocal->pull_up_hs400 = autocal->pull_up_1v8;
> -
> - err = device_property_read_u32(host->mmc->parent,
> - "nvidia,pad-autocal-pull-down-offset-hs400",
> - &autocal->pull_down_hs400);
> - if (err)
> - autocal->pull_down_hs400 = autocal->pull_down_1v8;
> }
>
> static void tegra_sdhci_request(struct mmc_host *mmc, struct mmc_request *mrq)
> --
> 2.7.4
>