From: Ganapathi Bhat <[email protected]>
This patch implement firmware download feature for
Marvell Bluetooth devices. If firmware is already
downloaded, it will skip downloading.
Signed-off-by: Ganapathi Bhat <[email protected]>
Signed-off-by: Amitkumar Karwar <[email protected]>
---
v2: Fixed compilation warning reported by kbuild test robot
v3: Addressed review comments from Marcel Holtmann
a) Removed vendor specific code from hci_ldisc.c
b) Get rid of static forward declaration
c) Removed unnecessary heavy nesting
d) Git rid of module parameter and global variables
e) Add logic to pick right firmware image
v4: Addresses review comments from Alan
a) Use existing kernel helper APIs instead of writing own.
b) Replace mdelay() with msleep()
v5: Addresses review comments from Loic Poulain
a) Use bt_dev_err/warn/dbg helpers insted of BT_ERR/WARN/DBG
b) Used static functions where required and removed forward delcarations
c) Edited comments for the function hci_uart_recv_data
d) Made HCI_UART_DNLD_FW flag a part of driver private data
v6: Addresses review comments from Loic Poulain
a) Used skb instead of array to store firmware data during download
b) Used hci_uart_tx_wakeup and enqueued packets instead of tty write
c) Used GFP_KERNEL instead of GFP_ATOMIC
v7: Edited Kconfig to add dependency for BT_HCIUART_H4. The change resolves
errors reported by kbuild test robot.
---
drivers/bluetooth/Kconfig | 11 +
drivers/bluetooth/Makefile | 1 +
drivers/bluetooth/btmrvl.h | 43 ++++
drivers/bluetooth/hci_ldisc.c | 6 +
drivers/bluetooth/hci_mrvl.c | 568 ++++++++++++++++++++++++++++++++++++++++++
drivers/bluetooth/hci_uart.h | 8 +-
6 files changed, 636 insertions(+), 1 deletion(-)
create mode 100644 drivers/bluetooth/btmrvl.h
create mode 100644 drivers/bluetooth/hci_mrvl.c
diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig
index cf50fd2..daafd0c 100644
--- a/drivers/bluetooth/Kconfig
+++ b/drivers/bluetooth/Kconfig
@@ -180,6 +180,17 @@ config BT_HCIUART_AG6XX
Say Y here to compile support for Intel AG6XX protocol.
+config BT_HCIUART_MRVL
+ bool "Marvell protocol support"
+ depends on BT_HCIUART
+ select BT_HCIUART_H4
+ help
+ Marvell is serial protocol for communication between Bluetooth
+ device and host. This protocol is required for most Marvell Bluetooth
+ devices with UART interface.
+
+ Say Y here to compile support for HCI MRVL protocol.
+
config BT_HCIBCM203X
tristate "HCI BCM203x USB driver"
depends on USB
diff --git a/drivers/bluetooth/Makefile b/drivers/bluetooth/Makefile
index 9c18939..364dbb6 100644
--- a/drivers/bluetooth/Makefile
+++ b/drivers/bluetooth/Makefile
@@ -37,6 +37,7 @@ hci_uart-$(CONFIG_BT_HCIUART_INTEL) += hci_intel.o
hci_uart-$(CONFIG_BT_HCIUART_BCM) += hci_bcm.o
hci_uart-$(CONFIG_BT_HCIUART_QCA) += hci_qca.o
hci_uart-$(CONFIG_BT_HCIUART_AG6XX) += hci_ag6xx.o
+hci_uart-$(CONFIG_BT_HCIUART_MRVL) += hci_mrvl.o
hci_uart-objs := $(hci_uart-y)
ccflags-y += -D__CHECK_ENDIAN__
diff --git a/drivers/bluetooth/btmrvl.h b/drivers/bluetooth/btmrvl.h
new file mode 100644
index 0000000..66855de
--- /dev/null
+++ b/drivers/bluetooth/btmrvl.h
@@ -0,0 +1,43 @@
+/* Bluetooth support for Marvell devices
+ *
+ * Copyright (C) 2016, Marvell International Ltd.
+ *
+ * This software file (the "File") is distributed by Marvell International
+ * Ltd. under the terms of the GNU General Public License Version 2, June 1991
+ * (the "License"). You may use, redistribute and/or modify this File in
+ * accordance with the terms and conditions of the License, a copy of which
+ * is available on the worldwide web at
+ * http://www.gnu.org/licenses/old-licenses/gpl-2.0.txt.
+ *
+ * THE FILE IS DISTRIBUTED AS-IS, WITHOUT WARRANTY OF ANY KIND, AND THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
+ * ARE EXPRESSLY DISCLAIMED. The License provides additional details about
+ * this warranty disclaimer.
+ */
+
+struct fw_data {
+ wait_queue_head_t init_wait_q __aligned(4);
+ u8 wait_fw;
+ int next_len;
+ u8 five_bytes[5];
+ u8 next_index;
+ u8 last_ack;
+ u8 expected_ack;
+ struct ktermios old_termios;
+ u8 chip_id;
+ u8 chip_rev;
+ struct sk_buff *skb;
+};
+
+#define MRVL_HELPER_NAME "mrvl/helper_uart_3000000.bin"
+#define MRVL_8997_FW_NAME "mrvl/uart8997_bt.bin"
+#define MRVL_WAIT_TIMEOUT 12000
+#define MRVL_MAX_FW_BLOCK_SIZE 1024
+#define MRVL_MAX_RETRY_SEND 12
+#define MRVL_DNLD_DELAY 100
+#define MRVL_ACK 0x5A
+#define MRVL_NAK 0xBF
+#define MRVL_HDR_REQ_FW 0xA5
+#define MRVL_HDR_CHIP_VER 0xAA
+#define MRVL_HCI_OP_SET_BAUD 0xFC09
+#define MRVL_FW_HDR_LEN 5
diff --git a/drivers/bluetooth/hci_ldisc.c b/drivers/bluetooth/hci_ldisc.c
index c00168a..b858758 100644
--- a/drivers/bluetooth/hci_ldisc.c
+++ b/drivers/bluetooth/hci_ldisc.c
@@ -807,6 +807,9 @@ static int __init hci_uart_init(void)
#ifdef CONFIG_BT_HCIUART_AG6XX
ag6xx_init();
#endif
+#ifdef CONFIG_BT_HCIUART_MRVL
+ mrvl_init();
+#endif
return 0;
}
@@ -842,6 +845,9 @@ static void __exit hci_uart_exit(void)
#ifdef CONFIG_BT_HCIUART_AG6XX
ag6xx_deinit();
#endif
+#ifdef CONFIG_BT_HCIUART_MRVL
+ mrvl_deinit();
+#endif
/* Release tty registration of line discipline */
err = tty_unregister_ldisc(N_HCI);
diff --git a/drivers/bluetooth/hci_mrvl.c b/drivers/bluetooth/hci_mrvl.c
new file mode 100644
index 0000000..bca47fd
--- /dev/null
+++ b/drivers/bluetooth/hci_mrvl.c
@@ -0,0 +1,568 @@
+/* Bluetooth HCI UART driver for Marvell devices
+ *
+ * Copyright (C) 2016, Marvell International Ltd.
+ *
+ * Acknowledgements:
+ * This file is based on hci_h4.c, which was written
+ * by Maxim Krasnyansky and Marcel Holtmann.
+ *
+ * This software file (the "File") is distributed by Marvell International
+ * Ltd. under the terms of the GNU General Public License Version 2, June 1991
+ * (the "License"). You may use, redistribute and/or modify this File in
+ * accordance with the terms and conditions of the License, a copy of which
+ * is available on the worldwide web at
+ * http://www.gnu.org/licenses/old-licenses/gpl-2.0.txt.
+ *
+ * THE FILE IS DISTRIBUTED AS-IS, WITHOUT WARRANTY OF ANY KIND, AND THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
+ * ARE EXPRESSLY DISCLAIMED. The License provides additional details about
+ * this warranty disclaimer.
+ */
+
+#include <linux/module.h>
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/fcntl.h>
+#include <linux/interrupt.h>
+#include <linux/ptrace.h>
+#include <linux/poll.h>
+#include <linux/firmware.h>
+#include <linux/version.h>
+#include <linux/slab.h>
+#include <linux/tty.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/signal.h>
+#include <linux/ioctl.h>
+#include <linux/skbuff.h>
+#include <asm/unaligned.h>
+
+#include <net/bluetooth/bluetooth.h>
+#include <net/bluetooth/hci_core.h>
+
+#include "hci_uart.h"
+#include "btmrvl.h"
+
+#define HCI_UART_DNLD_FW 2
+
+struct mrvl_data {
+ struct sk_buff *rx_skb;
+ struct sk_buff_head txq;
+ struct fw_data *fwdata;
+ unsigned long flags;
+};
+
+static int get_cts(struct hci_uart *hu)
+{
+ struct tty_struct *tty = hu->tty;
+ u32 state;
+
+ if (tty->ops->tiocmget) {
+ state = tty->ops->tiocmget(tty);
+ if (state & TIOCM_CTS) {
+ bt_dev_dbg(hu->hdev, "CTS is low");
+ return 1;
+ }
+ bt_dev_dbg(hu->hdev, "CTS is high");
+ return 0;
+ }
+ return -1;
+}
+
+/* Initialize protocol */
+static int mrvl_open(struct hci_uart *hu)
+{
+ struct mrvl_data *mrvl;
+
+ bt_dev_dbg(hu->hdev, "hu %p", hu);
+
+ mrvl = kzalloc(sizeof(*mrvl), GFP_KERNEL);
+ if (!mrvl)
+ return -ENOMEM;
+
+ skb_queue_head_init(&mrvl->txq);
+ hu->priv = mrvl;
+
+ return 0;
+}
+
+/* Flush protocol data */
+static int mrvl_flush(struct hci_uart *hu)
+{
+ struct mrvl_data *mrvl = hu->priv;
+
+ bt_dev_dbg(hu->hdev, "hu %p", hu);
+
+ skb_queue_purge(&mrvl->txq);
+
+ return 0;
+}
+
+/* Close protocol */
+static int mrvl_close(struct hci_uart *hu)
+{
+ struct mrvl_data *mrvl = hu->priv;
+
+ bt_dev_dbg(hu->hdev, "hu %p", hu);
+
+ skb_queue_purge(&mrvl->txq);
+ kfree_skb(mrvl->rx_skb);
+ kfree(mrvl->fwdata);
+ hu->priv = NULL;
+ kfree(mrvl);
+
+ return 0;
+}
+
+/* Enqueue frame for transmittion (padding, crc, etc) */
+static int mrvl_enqueue(struct hci_uart *hu, struct sk_buff *skb)
+{
+ struct mrvl_data *mrvl = hu->priv;
+
+ if (test_bit(HCI_UART_DNLD_FW, &mrvl->flags))
+ return -EBUSY;
+
+ bt_dev_dbg(hu->hdev, "hu %p skb %p", hu, skb);
+
+ /* Prepend skb with frame type */
+ memcpy(skb_push(skb, 1), &hci_skb_pkt_type(skb), 1);
+ skb_queue_tail(&mrvl->txq, skb);
+
+ return 0;
+}
+
+static const struct h4_recv_pkt mrvl_recv_pkts[] = {
+ { H4_RECV_ACL, .recv = hci_recv_frame },
+ { H4_RECV_SCO, .recv = hci_recv_frame },
+ { H4_RECV_EVENT, .recv = hci_recv_frame },
+};
+
+/* Send ACK/NAK to the device */
+static void mrvl_send_ack(struct hci_uart *hu, unsigned char ack)
+{
+ struct tty_struct *tty = hu->tty;
+
+ tty->ops->write(tty, &ack, sizeof(ack));
+}
+
+/* Validate the feedback data from device */
+static void mrvl_pkt_complete(struct hci_uart *hu, struct sk_buff *skb)
+{
+ struct mrvl_data *mrvl = hu->priv;
+ struct fw_data *fw_data = mrvl->fwdata;
+ u8 buf[MRVL_FW_HDR_LEN];
+ u16 lhs, rhs;
+
+ memcpy(buf, skb->data, skb->len);
+
+ lhs = le16_to_cpu(*((__le16 *)(&buf[1])));
+ rhs = le16_to_cpu(*((__le16 *)(&buf[3])));
+ if ((lhs ^ rhs) == 0xffff) {
+ mrvl_send_ack(hu, MRVL_ACK);
+ fw_data->wait_fw = 1;
+ fw_data->next_len = lhs;
+ /*firmware download is done, send the last ack*/
+ if (!lhs)
+ fw_data->last_ack = 1;
+
+ if (unlikely(fw_data->expected_ack == MRVL_HDR_CHIP_VER)) {
+ fw_data->chip_id = *((u8 *)(&buf[1]));
+ fw_data->chip_rev = *((u8 *)(&buf[2]));
+ }
+ wake_up_interruptible(&fw_data->init_wait_q);
+ } else {
+ mrvl_send_ack(hu, MRVL_NAK);
+ }
+}
+
+/* This function receives data from the uart device during firmware download.
+ * Driver expects 5 bytes of data as per the protocal in the below format:
+ * <HEADER><BYTE_1><BYTE_2><BYTE_3><BYTE_4>
+ * BYTE_3 and BYTE_4 are compliment of BYTE_1 an BYTE_2. Data can come in chunks
+ * of any length. If length received is < 5, accumulate the data in an array,
+ * until we have a sequence of 5 bytes, starting with the expected HEADER. If
+ * the length received is > 5 bytes, then get the first 5 bytes, starting with
+ * the HEADER and process the same, ignoring the rest of the bytes as per the
+ * protocal.
+ */
+static struct sk_buff *mrvl_process_fw_data(struct hci_uart *hu,
+ struct sk_buff *skb,
+ u8 *buf, int count)
+{
+ struct mrvl_data *mrvl = hu->priv;
+ struct fw_data *fw_data = mrvl->fwdata;
+ int i = 0, len;
+
+ if (!skb) {
+ while (buf[i] != fw_data->expected_ack && i < count)
+ i++;
+ if (i == count)
+ return ERR_PTR(-EILSEQ);
+
+ skb = bt_skb_alloc(MRVL_FW_HDR_LEN, GFP_KERNEL);
+ }
+
+ if (!skb)
+ return ERR_PTR(-ENOMEM);
+
+ len = count - i;
+ memcpy(skb_put(skb, len), &buf[i], len);
+
+ if (skb->len == MRVL_FW_HDR_LEN) {
+ mrvl_pkt_complete(hu, skb);
+ kfree_skb(skb);
+ skb = NULL;
+ }
+
+ return skb;
+}
+
+/* Receive data */
+static int mrvl_recv(struct hci_uart *hu, const void *data, int count)
+{
+ struct mrvl_data *mrvl = hu->priv;
+
+ if (test_bit(HCI_UART_DNLD_FW, &mrvl->flags)) {
+ mrvl->fwdata->skb = mrvl_process_fw_data(hu, mrvl->fwdata->skb,
+ (u8 *)data, count);
+ if (IS_ERR(mrvl->fwdata->skb)) {
+ int err = PTR_ERR(mrvl->fwdata->skb);
+
+ bt_dev_err(hu->hdev,
+ "Receive firmware data failed (%d)", err);
+ mrvl->fwdata->skb = NULL;
+ return err;
+ }
+ return 0;
+ }
+
+ if (!test_bit(HCI_UART_REGISTERED, &hu->flags))
+ return -EUNATCH;
+
+ mrvl->rx_skb = h4_recv_buf(hu->hdev, mrvl->rx_skb, data, count,
+ mrvl_recv_pkts, ARRAY_SIZE(mrvl_recv_pkts));
+ if (IS_ERR(mrvl->rx_skb)) {
+ int err = PTR_ERR(mrvl->rx_skb);
+
+ bt_dev_err(hu->hdev, "Frame reassembly failed (%d)", err);
+ mrvl->rx_skb = NULL;
+ return err;
+ }
+
+ return count;
+}
+
+static struct sk_buff *mrvl_dequeue(struct hci_uart *hu)
+{
+ struct mrvl_data *mrvl = hu->priv;
+
+ return skb_dequeue(&mrvl->txq);
+}
+
+static int mrvl_init_fw_data(struct hci_uart *hu)
+{
+ struct fw_data *fwdata;
+ struct mrvl_data *mrvl = hu->priv;
+
+ fwdata = kzalloc(sizeof(*fwdata), GFP_KERNEL);
+
+ if (!fwdata)
+ return -ENOMEM;
+
+ mrvl->fwdata = fwdata;
+ init_waitqueue_head(&fwdata->init_wait_q);
+
+ return 0;
+}
+
+/* Wait for the header from device */
+static int mrvl_wait_for_hdr(struct hci_uart *hu, u8 header)
+{
+ struct mrvl_data *mrvl = hu->priv;
+ struct fw_data *fw_data = mrvl->fwdata;
+
+ fw_data->expected_ack = header;
+ fw_data->wait_fw = 0;
+
+ if (!wait_event_interruptible_timeout(fw_data->init_wait_q,
+ fw_data->wait_fw,
+ ((MRVL_WAIT_TIMEOUT) * HZ / 1000))) {
+ bt_dev_err(hu->hdev, "TIMEOUT, waiting for:0x%x",
+ fw_data->expected_ack);
+ return -1;
+ }
+
+ return 0;
+}
+
+/* Send bytes to device */
+static int mrvl_send_data(struct hci_uart *hu, struct sk_buff *skb)
+{
+ struct mrvl_data *mrvl = hu->priv;
+
+ skb_queue_head(&mrvl->txq, skb);
+ hci_uart_tx_wakeup(hu);
+
+ if (mrvl_wait_for_hdr(hu, MRVL_HDR_REQ_FW) == -1)
+ return -1;
+
+ return 0;
+}
+
+static struct sk_buff *mrvl_alloc_skb(struct hci_dev *hdev)
+{
+ struct sk_buff *skb = NULL;
+
+ skb = bt_skb_alloc(MRVL_MAX_FW_BLOCK_SIZE, GFP_KERNEL);
+ if (!skb)
+ bt_dev_err(hdev, "cannot allocate memory for skb");
+ else
+ skb->dev = (void *)hdev;
+
+ return skb;
+}
+
+/* Download firmware to the device */
+static int mrvl_dnld_fw(struct hci_uart *hu, const char *file_name)
+{
+ struct hci_dev *hdev = hu->hdev;
+ const struct firmware *fw = NULL;
+ struct sk_buff *skb = NULL;
+ int offset = 0;
+ int ret, tx_len;
+ struct mrvl_data *mrvl = hu->priv;
+ struct fw_data *fw_data = mrvl->fwdata;
+
+ ret = request_firmware(&fw, file_name, &hdev->dev);
+ if (ret < 0) {
+ bt_dev_err(hu->hdev, "request_firmware() failed");
+ return -1;
+ }
+
+ bt_dev_info(hu->hdev, "Downloading FW (%d bytes)", (u16)fw->size);
+
+ fw_data->last_ack = 0;
+
+ do {
+ if ((offset >= fw->size) || (fw_data->last_ack))
+ break;
+ tx_len = fw_data->next_len;
+ if ((fw->size - offset) < tx_len)
+ tx_len = fw->size - offset;
+
+ skb = mrvl_alloc_skb(hdev);
+ if (!skb) {
+ ret = -1;
+ goto done;
+ }
+
+ memcpy(skb->data, &fw->data[offset], tx_len);
+ skb_put(skb, tx_len);
+ if (mrvl_send_data(hu, skb) != 0) {
+ bt_dev_err(hu->hdev, "fail to download firmware");
+ ret = -1;
+ goto done;
+ }
+ offset += tx_len;
+ } while (1);
+
+ bt_dev_info(hu->hdev, "downloaded %d byte firmware", offset);
+done:
+ release_firmware(fw);
+
+ return ret;
+}
+
+/* Set the baud rate */
+static int mrvl_set_dev_baud(struct hci_uart *hu)
+{
+ struct hci_dev *hdev = hu->hdev;
+ struct sk_buff *skb;
+ static const u8 baud_param[] = { 0xc0, 0xc6, 0x2d, 0x00 };
+ int err;
+
+ skb = __hci_cmd_sync(hdev, MRVL_HCI_OP_SET_BAUD, sizeof(baud_param),
+ baud_param, HCI_INIT_TIMEOUT);
+ if (IS_ERR(skb)) {
+ err = PTR_ERR(skb);
+ bt_dev_err(hu->hdev, "Set device baudrate failed (%d)", err);
+ return err;
+ }
+ kfree_skb(skb);
+
+ return 0;
+}
+
+/* Reset device */
+static int mrvl_reset(struct hci_uart *hu)
+{
+ struct hci_dev *hdev = hu->hdev;
+ struct sk_buff *skb;
+ int err;
+
+ skb = __hci_cmd_sync(hdev, HCI_OP_RESET, 0, NULL, HCI_CMD_TIMEOUT);
+ if (IS_ERR(skb)) {
+ err = PTR_ERR(skb);
+ bt_dev_err(hu->hdev, "Reset device failed (%d)", err);
+ return err;
+ }
+ kfree_skb(skb);
+
+ return 0;
+}
+
+static int mrvl_set_baud(struct hci_uart *hu)
+{
+ int err;
+
+ hci_uart_set_baudrate(hu, 115200);
+ hci_uart_set_flow_control(hu, false);
+
+ err = mrvl_reset(hu);
+ if (err)
+ goto set_term_baud;
+ else
+ goto set_dev_baud;
+
+set_dev_baud:
+ err = mrvl_set_dev_baud(hu);
+ if (err)
+ return -1;
+
+set_term_baud:
+ hci_uart_set_baudrate(hu, 3000000);
+ hci_uart_set_flow_control(hu, false);
+
+ return 0;
+}
+
+static int mrvl_get_fw_name(struct hci_uart *hu, char *fw_name)
+{
+ int ret;
+ struct mrvl_data *mrvl = hu->priv;
+ struct fw_data *fw_data = mrvl->fwdata;
+
+ ret = mrvl_wait_for_hdr(hu, MRVL_HDR_CHIP_VER);
+ if (ret) {
+ ret = -1;
+ bt_dev_err(hu->hdev, "Could not read chip id and revision");
+ goto fail;
+ }
+
+ bt_dev_dbg(hu->hdev, "chip_id=0x%x, chip_rev=0x%x",
+ fw_data->chip_id, fw_data->chip_rev);
+
+ if (fw_data->chip_id == 0x50) {
+ memcpy(fw_name, MRVL_8997_FW_NAME, sizeof(MRVL_8997_FW_NAME));
+ } else {
+ ret = -1;
+ bt_dev_err(hu->hdev, "Invalid chip id");
+ }
+fail:
+ return ret;
+}
+
+/* Download helper and firmare to device */
+static int hci_uart_dnld_fw(struct hci_uart *hu)
+{
+ struct tty_struct *tty = hu->tty;
+ struct ktermios new_termios;
+ struct ktermios old_termios;
+ struct mrvl_data *mrvl = hu->priv;
+ char fw_name[128];
+ int ret;
+
+ old_termios = tty->termios;
+
+ if (get_cts(hu)) {
+ bt_dev_info(hu->hdev, "fw is running");
+ clear_bit(HCI_UART_DNLD_FW, &mrvl->flags);
+ goto set_baud;
+ }
+
+ hci_uart_set_baudrate(hu, 115200);
+ hci_uart_set_flow_control(hu, true);
+
+ ret = mrvl_wait_for_hdr(hu, MRVL_HDR_REQ_FW);
+ if (ret)
+ goto fail;
+
+ ret = mrvl_dnld_fw(hu, MRVL_HELPER_NAME);
+ if (ret)
+ goto fail;
+
+ msleep(MRVL_DNLD_DELAY);
+
+ hci_uart_set_baudrate(hu, 3000000);
+ hci_uart_set_flow_control(hu, false);
+
+ ret = mrvl_get_fw_name(hu, fw_name);
+ if (ret)
+ goto fail;
+
+ ret = mrvl_wait_for_hdr(hu, MRVL_HDR_REQ_FW);
+ if (ret)
+ goto fail;
+
+ ret = mrvl_dnld_fw(hu, fw_name);
+ if (ret)
+ goto fail;
+
+ msleep(MRVL_DNLD_DELAY);
+ /* restore uart settings */
+ new_termios = tty->termios;
+ tty->termios.c_cflag = old_termios.c_cflag;
+ tty_set_termios(tty, &new_termios);
+ clear_bit(HCI_UART_DNLD_FW, &mrvl->flags);
+
+set_baud:
+ ret = mrvl_set_baud(hu);
+ if (ret)
+ goto fail;
+
+ msleep(MRVL_DNLD_DELAY);
+
+ return ret;
+fail:
+ /* restore uart settings */
+ new_termios = tty->termios;
+ tty->termios.c_cflag = old_termios.c_cflag;
+ tty_set_termios(tty, &new_termios);
+ clear_bit(HCI_UART_DNLD_FW, &mrvl->flags);
+
+ return ret;
+}
+
+static int mrvl_setup(struct hci_uart *hu)
+{
+ struct mrvl_data *mrvl = hu->priv;
+
+ mrvl_init_fw_data(hu);
+ set_bit(HCI_UART_DNLD_FW, &mrvl->flags);
+
+ return hci_uart_dnld_fw(hu);
+}
+
+static const struct hci_uart_proto mrvlp = {
+ .id = HCI_UART_MRVL,
+ .name = "MRVL",
+ .open = mrvl_open,
+ .close = mrvl_close,
+ .recv = mrvl_recv,
+ .enqueue = mrvl_enqueue,
+ .dequeue = mrvl_dequeue,
+ .flush = mrvl_flush,
+ .setup = mrvl_setup,
+};
+
+int __init mrvl_init(void)
+{
+ return hci_uart_register_proto(&mrvlp);
+}
+
+int __exit mrvl_deinit(void)
+{
+ return hci_uart_unregister_proto(&mrvlp);
+}
diff --git a/drivers/bluetooth/hci_uart.h b/drivers/bluetooth/hci_uart.h
index 4814ff0..8b1f744 100644
--- a/drivers/bluetooth/hci_uart.h
+++ b/drivers/bluetooth/hci_uart.h
@@ -35,7 +35,7 @@
#define HCIUARTGETFLAGS _IOR('U', 204, int)
/* UART protocols */
-#define HCI_UART_MAX_PROTO 10
+#define HCI_UART_MAX_PROTO 11
#define HCI_UART_H4 0
#define HCI_UART_BCSP 1
@@ -47,6 +47,7 @@
#define HCI_UART_BCM 7
#define HCI_UART_QCA 8
#define HCI_UART_AG6XX 9
+#define HCI_UART_MRVL 10
#define HCI_UART_RAW_DEVICE 0
#define HCI_UART_RESET_ON_INIT 1
@@ -188,3 +189,8 @@ int qca_deinit(void);
int ag6xx_init(void);
int ag6xx_deinit(void);
#endif
+
+#ifdef CONFIG_BT_HCIUART_MRVL
+int mrvl_init(void);
+int mrvl_deinit(void);
+#endif
--
1.9.1
Hi Amitkumar,
> Thanks for your review.
> We will address these comments in updated version.
>
>>> +
>>> +/* Receive data */
>>> +static int mrvl_recv(struct hci_uart *hu, const void *data, int
>>> +count) {
>>> + struct mrvl_data *mrvl = hu->priv;
>>> +
>>> + if (test_bit(HCI_UART_DNLD_FW, &mrvl->flags)) {
>>> + mrvl->fwdata->skb = mrvl_process_fw_data(hu, mrvl->fwdata-
>>> skb,
>>> + (u8 *)data, count);
>>> + if (IS_ERR(mrvl->fwdata->skb)) {
>>> + int err = PTR_ERR(mrvl->fwdata->skb);
>>> +
>>> + bt_dev_err(hu->hdev,
>>> + "Receive firmware data failed (%d)", err);
>>> + mrvl->fwdata->skb = NULL;
>>> + return err;
>>> + }
>>> + return 0;
>>> + }
>>
>> This part actually worries me a bit. Yes, we can do it this way, but in
>> general it sounds a bit more like we need a generic approach in
>> hci_ldisc.c to handle pre-HCI firmware loading and/or setup.
>>
>> In the btusb.c driver we added ->setup_on_usb callback. And for it
>> sounds like we need something similar here. So that hci_ldisc.c can
>> handle most of the basic TX/RX.
>
> Even if we added "->setup_on_usb" in hci_ldisc.c, we will need protocol specific changes in receive path during firmware download.
> With this patch, those changes are smoothly handled in hci_mrvl.c file.
> [hci_uart_tty_receive] -> [proto->recv] -> [mrvl_recv] -> [normal Rx path/FW download Rx handling]
we might need to find a better callback name, but yes, we want to make this generic in hci_ldisc.c. I do not have a perfect solution or quick answer, but I think this needs a bit more generic framework.
Regards
Marcel
Hi Marcel,
Thanks for your review.
We will address these comments in updated version.
> > +
> > +/* Receive data */
> > +static int mrvl_recv(struct hci_uart *hu, const void *data, int
> > +count) {
> > + struct mrvl_data *mrvl =3D hu->priv;
> > +
> > + if (test_bit(HCI_UART_DNLD_FW, &mrvl->flags)) {
> > + mrvl->fwdata->skb =3D mrvl_process_fw_data(hu, mrvl->fwdata-
> >skb,
> > + (u8 *)data, count);
> > + if (IS_ERR(mrvl->fwdata->skb)) {
> > + int err =3D PTR_ERR(mrvl->fwdata->skb);
> > +
> > + bt_dev_err(hu->hdev,
> > + "Receive firmware data failed (%d)", err);
> > + mrvl->fwdata->skb =3D NULL;
> > + return err;
> > + }
> > + return 0;
> > + }
>=20
> This part actually worries me a bit. Yes, we can do it this way, but in
> general it sounds a bit more like we need a generic approach in
> hci_ldisc.c to handle pre-HCI firmware loading and/or setup.
>=20
> In the btusb.c driver we added ->setup_on_usb callback. And for it
> sounds like we need something similar here. So that hci_ldisc.c can
> handle most of the basic TX/RX.
Even if we added "->setup_on_usb" in hci_ldisc.c, we will need protocol spe=
cific changes in receive path during firmware download.
With this patch, those changes are smoothly handled in hci_mrvl.c file.
[hci_uart_tty_receive] -> [proto->recv] -> [mrvl_recv] -> [normal Rx path/F=
W download Rx handling]
> > +
> > +static int mrvl_setup(struct hci_uart *hu) {
> > + struct mrvl_data *mrvl =3D hu->priv;
> > +
> > + mrvl_init_fw_data(hu);
> > + set_bit(HCI_UART_DNLD_FW, &mrvl->flags);
> > +
> > + return hci_uart_dnld_fw(hu);
> > +}
>=20
> So this is clearly the wrong spot. When ->setup is called it is expected
> that HCI is ready. You are misusing it here.
>=20
Sure. We will move this to mrvl_open() where HCI is not yet initialized.
Regards,
Amitkumar
Hi Amitkumar,
> This patch implement firmware download feature for
> Marvell Bluetooth devices. If firmware is already
> downloaded, it will skip downloading.
>
> Signed-off-by: Ganapathi Bhat <[email protected]>
> Signed-off-by: Amitkumar Karwar <[email protected]>
> ---
> v2: Fixed compilation warning reported by kbuild test robot
> v3: Addressed review comments from Marcel Holtmann
> a) Removed vendor specific code from hci_ldisc.c
> b) Get rid of static forward declaration
> c) Removed unnecessary heavy nesting
> d) Git rid of module parameter and global variables
> e) Add logic to pick right firmware image
> v4: Addresses review comments from Alan
> a) Use existing kernel helper APIs instead of writing own.
> b) Replace mdelay() with msleep()
> v5: Addresses review comments from Loic Poulain
> a) Use bt_dev_err/warn/dbg helpers insted of BT_ERR/WARN/DBG
> b) Used static functions where required and removed forward delcarations
> c) Edited comments for the function hci_uart_recv_data
> d) Made HCI_UART_DNLD_FW flag a part of driver private data
> v6: Addresses review comments from Loic Poulain
> a) Used skb instead of array to store firmware data during download
> b) Used hci_uart_tx_wakeup and enqueued packets instead of tty write
> c) Used GFP_KERNEL instead of GFP_ATOMIC
> v7: Edited Kconfig to add dependency for BT_HCIUART_H4. The change resolves
> errors reported by kbuild test robot.
> ---
> drivers/bluetooth/Kconfig | 11 +
> drivers/bluetooth/Makefile | 1 +
> drivers/bluetooth/btmrvl.h | 43 ++++
> drivers/bluetooth/hci_ldisc.c | 6 +
> drivers/bluetooth/hci_mrvl.c | 568 ++++++++++++++++++++++++++++++++++++++++++
> drivers/bluetooth/hci_uart.h | 8 +-
> 6 files changed, 636 insertions(+), 1 deletion(-)
> create mode 100644 drivers/bluetooth/btmrvl.h
> create mode 100644 drivers/bluetooth/hci_mrvl.c
>
> diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig
> index cf50fd2..daafd0c 100644
> --- a/drivers/bluetooth/Kconfig
> +++ b/drivers/bluetooth/Kconfig
> @@ -180,6 +180,17 @@ config BT_HCIUART_AG6XX
>
> Say Y here to compile support for Intel AG6XX protocol.
>
> +config BT_HCIUART_MRVL
> + bool "Marvell protocol support"
> + depends on BT_HCIUART
> + select BT_HCIUART_H4
> + help
> + Marvell is serial protocol for communication between Bluetooth
> + device and host. This protocol is required for most Marvell Bluetooth
> + devices with UART interface.
> +
> + Say Y here to compile support for HCI MRVL protocol.
> +
> config BT_HCIBCM203X
> tristate "HCI BCM203x USB driver"
> depends on USB
> diff --git a/drivers/bluetooth/Makefile b/drivers/bluetooth/Makefile
> index 9c18939..364dbb6 100644
> --- a/drivers/bluetooth/Makefile
> +++ b/drivers/bluetooth/Makefile
> @@ -37,6 +37,7 @@ hci_uart-$(CONFIG_BT_HCIUART_INTEL) += hci_intel.o
> hci_uart-$(CONFIG_BT_HCIUART_BCM) += hci_bcm.o
> hci_uart-$(CONFIG_BT_HCIUART_QCA) += hci_qca.o
> hci_uart-$(CONFIG_BT_HCIUART_AG6XX) += hci_ag6xx.o
> +hci_uart-$(CONFIG_BT_HCIUART_MRVL) += hci_mrvl.o
> hci_uart-objs := $(hci_uart-y)
>
> ccflags-y += -D__CHECK_ENDIAN__
> diff --git a/drivers/bluetooth/btmrvl.h b/drivers/bluetooth/btmrvl.h
> new file mode 100644
> index 0000000..66855de
> --- /dev/null
> +++ b/drivers/bluetooth/btmrvl.h
> @@ -0,0 +1,43 @@
> +/* Bluetooth support for Marvell devices
> + *
> + * Copyright (C) 2016, Marvell International Ltd.
> + *
> + * This software file (the "File") is distributed by Marvell International
> + * Ltd. under the terms of the GNU General Public License Version 2, June 1991
> + * (the "License"). You may use, redistribute and/or modify this File in
> + * accordance with the terms and conditions of the License, a copy of which
> + * is available on the worldwide web at
> + * http://www.gnu.org/licenses/old-licenses/gpl-2.0.txt.
> + *
> + * THE FILE IS DISTRIBUTED AS-IS, WITHOUT WARRANTY OF ANY KIND, AND THE
> + * IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
> + * ARE EXPRESSLY DISCLAIMED. The License provides additional details about
> + * this warranty disclaimer.
> + */
> +
> +struct fw_data {
> + wait_queue_head_t init_wait_q __aligned(4);
why does this need to be aligned?
> + u8 wait_fw;
> + int next_len;
> + u8 five_bytes[5];
> + u8 next_index;
> + u8 last_ack;
> + u8 expected_ack;
> + struct ktermios old_termios;
> + u8 chip_id;
> + u8 chip_rev;
> + struct sk_buff *skb;
> +};
> +
> +#define MRVL_HELPER_NAME "mrvl/helper_uart_3000000.bin"
> +#define MRVL_8997_FW_NAME "mrvl/uart8997_bt.bin"
> +#define MRVL_WAIT_TIMEOUT 12000
> +#define MRVL_MAX_FW_BLOCK_SIZE 1024
> +#define MRVL_MAX_RETRY_SEND 12
> +#define MRVL_DNLD_DELAY 100
> +#define MRVL_ACK 0x5A
> +#define MRVL_NAK 0xBF
> +#define MRVL_HDR_REQ_FW 0xA5
> +#define MRVL_HDR_CHIP_VER 0xAA
> +#define MRVL_HCI_OP_SET_BAUD 0xFC09
> +#define MRVL_FW_HDR_LEN 5
And if this is all hci_marvl.c specific, why do we bother with a generic header file. I would first try to keep it all in the C file and only split it out once it is actually used outside the driver.
> diff --git a/drivers/bluetooth/hci_ldisc.c b/drivers/bluetooth/hci_ldisc.c
> index c00168a..b858758 100644
> --- a/drivers/bluetooth/hci_ldisc.c
> +++ b/drivers/bluetooth/hci_ldisc.c
> @@ -807,6 +807,9 @@ static int __init hci_uart_init(void)
> #ifdef CONFIG_BT_HCIUART_AG6XX
> ag6xx_init();
> #endif
> +#ifdef CONFIG_BT_HCIUART_MRVL
> + mrvl_init();
> +#endif
>
> return 0;
> }
> @@ -842,6 +845,9 @@ static void __exit hci_uart_exit(void)
> #ifdef CONFIG_BT_HCIUART_AG6XX
> ag6xx_deinit();
> #endif
> +#ifdef CONFIG_BT_HCIUART_MRVL
> + mrvl_deinit();
> +#endif
>
> /* Release tty registration of line discipline */
> err = tty_unregister_ldisc(N_HCI);
> diff --git a/drivers/bluetooth/hci_mrvl.c b/drivers/bluetooth/hci_mrvl.c
> new file mode 100644
> index 0000000..bca47fd
> --- /dev/null
> +++ b/drivers/bluetooth/hci_mrvl.c
> @@ -0,0 +1,568 @@
> +/* Bluetooth HCI UART driver for Marvell devices
> + *
> + * Copyright (C) 2016, Marvell International Ltd.
> + *
> + * Acknowledgements:
> + * This file is based on hci_h4.c, which was written
> + * by Maxim Krasnyansky and Marcel Holtmann.
> + *
> + * This software file (the "File") is distributed by Marvell International
> + * Ltd. under the terms of the GNU General Public License Version 2, June 1991
> + * (the "License"). You may use, redistribute and/or modify this File in
> + * accordance with the terms and conditions of the License, a copy of which
> + * is available on the worldwide web at
> + * http://www.gnu.org/licenses/old-licenses/gpl-2.0.txt.
> + *
> + * THE FILE IS DISTRIBUTED AS-IS, WITHOUT WARRANTY OF ANY KIND, AND THE
> + * IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
> + * ARE EXPRESSLY DISCLAIMED. The License provides additional details about
> + * this warranty disclaimer.
> + */
> +
> +#include <linux/module.h>
> +
> +#include <linux/kernel.h>
> +#include <linux/init.h>
> +#include <linux/types.h>
> +#include <linux/fcntl.h>
> +#include <linux/interrupt.h>
> +#include <linux/ptrace.h>
> +#include <linux/poll.h>
> +#include <linux/firmware.h>
> +#include <linux/version.h>
> +#include <linux/slab.h>
> +#include <linux/tty.h>
> +#include <linux/errno.h>
> +#include <linux/string.h>
> +#include <linux/signal.h>
Are you sure all of these are needed? Some of them sound not like they are actually used.
> +#include <linux/ioctl.h>
> +#include <linux/skbuff.h>
> +#include <asm/unaligned.h>
> +
> +#include <net/bluetooth/bluetooth.h>
> +#include <net/bluetooth/hci_core.h>
> +
> +#include "hci_uart.h"
> +#include "btmrvl.h"
> +
> +#define HCI_UART_DNLD_FW 2
Why is this 2?
> +
> +struct mrvl_data {
> + struct sk_buff *rx_skb;
> + struct sk_buff_head txq;
> + struct fw_data *fwdata;
> + unsigned long flags;
> +};
> +
> +static int get_cts(struct hci_uart *hu)
> +{
> + struct tty_struct *tty = hu->tty;
> + u32 state;
> +
> + if (tty->ops->tiocmget) {
> + state = tty->ops->tiocmget(tty);
> + if (state & TIOCM_CTS) {
> + bt_dev_dbg(hu->hdev, "CTS is low");
> + return 1;
> + }
> + bt_dev_dbg(hu->hdev, "CTS is high");
> + return 0;
> + }
> + return -1;
> +}
Why is this a tristate and not just bool?
> +
> +/* Initialize protocol */
> +static int mrvl_open(struct hci_uart *hu)
> +{
> + struct mrvl_data *mrvl;
> +
> + bt_dev_dbg(hu->hdev, "hu %p", hu);
> +
> + mrvl = kzalloc(sizeof(*mrvl), GFP_KERNEL);
> + if (!mrvl)
> + return -ENOMEM;
> +
> + skb_queue_head_init(&mrvl->txq);
> + hu->priv = mrvl;
> +
> + return 0;
> +}
> +
> +/* Flush protocol data */
> +static int mrvl_flush(struct hci_uart *hu)
> +{
> + struct mrvl_data *mrvl = hu->priv;
> +
> + bt_dev_dbg(hu->hdev, "hu %p", hu);
> +
> + skb_queue_purge(&mrvl->txq);
> +
> + return 0;
> +}
> +
> +/* Close protocol */
> +static int mrvl_close(struct hci_uart *hu)
> +{
> + struct mrvl_data *mrvl = hu->priv;
> +
> + bt_dev_dbg(hu->hdev, "hu %p", hu);
> +
> + skb_queue_purge(&mrvl->txq);
> + kfree_skb(mrvl->rx_skb);
> + kfree(mrvl->fwdata);
> + hu->priv = NULL;
> + kfree(mrvl);
> +
> + return 0;
> +}
> +
> +/* Enqueue frame for transmittion (padding, crc, etc) */
> +static int mrvl_enqueue(struct hci_uart *hu, struct sk_buff *skb)
> +{
> + struct mrvl_data *mrvl = hu->priv;
> +
> + if (test_bit(HCI_UART_DNLD_FW, &mrvl->flags))
> + return -EBUSY;
> +
> + bt_dev_dbg(hu->hdev, "hu %p skb %p", hu, skb);
> +
> + /* Prepend skb with frame type */
> + memcpy(skb_push(skb, 1), &hci_skb_pkt_type(skb), 1);
> + skb_queue_tail(&mrvl->txq, skb);
> +
> + return 0;
> +}
> +
> +static const struct h4_recv_pkt mrvl_recv_pkts[] = {
> + { H4_RECV_ACL, .recv = hci_recv_frame },
> + { H4_RECV_SCO, .recv = hci_recv_frame },
> + { H4_RECV_EVENT, .recv = hci_recv_frame },
> +};
> +
> +/* Send ACK/NAK to the device */
> +static void mrvl_send_ack(struct hci_uart *hu, unsigned char ack)
> +{
> + struct tty_struct *tty = hu->tty;
> +
> + tty->ops->write(tty, &ack, sizeof(ack));
> +}
> +
> +/* Validate the feedback data from device */
> +static void mrvl_pkt_complete(struct hci_uart *hu, struct sk_buff *skb)
> +{
> + struct mrvl_data *mrvl = hu->priv;
> + struct fw_data *fw_data = mrvl->fwdata;
> + u8 buf[MRVL_FW_HDR_LEN];
> + u16 lhs, rhs;
> +
> + memcpy(buf, skb->data, skb->len);
> +
> + lhs = le16_to_cpu(*((__le16 *)(&buf[1])));
> + rhs = le16_to_cpu(*((__le16 *)(&buf[3])));
> + if ((lhs ^ rhs) == 0xffff) {
> + mrvl_send_ack(hu, MRVL_ACK);
> + fw_data->wait_fw = 1;
> + fw_data->next_len = lhs;
> + /*firmware download is done, send the last ack*/
> + if (!lhs)
> + fw_data->last_ack = 1;
> +
> + if (unlikely(fw_data->expected_ack == MRVL_HDR_CHIP_VER)) {
> + fw_data->chip_id = *((u8 *)(&buf[1]));
> + fw_data->chip_rev = *((u8 *)(&buf[2]));
> + }
> + wake_up_interruptible(&fw_data->init_wait_q);
> + } else {
> + mrvl_send_ack(hu, MRVL_NAK);
> + }
> +}
> +
> +/* This function receives data from the uart device during firmware download.
> + * Driver expects 5 bytes of data as per the protocal in the below format:
> + * <HEADER><BYTE_1><BYTE_2><BYTE_3><BYTE_4>
> + * BYTE_3 and BYTE_4 are compliment of BYTE_1 an BYTE_2. Data can come in chunks
> + * of any length. If length received is < 5, accumulate the data in an array,
> + * until we have a sequence of 5 bytes, starting with the expected HEADER. If
> + * the length received is > 5 bytes, then get the first 5 bytes, starting with
> + * the HEADER and process the same, ignoring the rest of the bytes as per the
> + * protocal.
> + */
> +static struct sk_buff *mrvl_process_fw_data(struct hci_uart *hu,
> + struct sk_buff *skb,
> + u8 *buf, int count)
> +{
> + struct mrvl_data *mrvl = hu->priv;
> + struct fw_data *fw_data = mrvl->fwdata;
> + int i = 0, len;
> +
> + if (!skb) {
> + while (buf[i] != fw_data->expected_ack && i < count)
> + i++;
> + if (i == count)
> + return ERR_PTR(-EILSEQ);
> +
> + skb = bt_skb_alloc(MRVL_FW_HDR_LEN, GFP_KERNEL);
> + }
> +
> + if (!skb)
> + return ERR_PTR(-ENOMEM);
> +
> + len = count - i;
> + memcpy(skb_put(skb, len), &buf[i], len);
> +
> + if (skb->len == MRVL_FW_HDR_LEN) {
> + mrvl_pkt_complete(hu, skb);
> + kfree_skb(skb);
> + skb = NULL;
> + }
> +
> + return skb;
> +}
> +
> +/* Receive data */
> +static int mrvl_recv(struct hci_uart *hu, const void *data, int count)
> +{
> + struct mrvl_data *mrvl = hu->priv;
> +
> + if (test_bit(HCI_UART_DNLD_FW, &mrvl->flags)) {
> + mrvl->fwdata->skb = mrvl_process_fw_data(hu, mrvl->fwdata->skb,
> + (u8 *)data, count);
> + if (IS_ERR(mrvl->fwdata->skb)) {
> + int err = PTR_ERR(mrvl->fwdata->skb);
> +
> + bt_dev_err(hu->hdev,
> + "Receive firmware data failed (%d)", err);
> + mrvl->fwdata->skb = NULL;
> + return err;
> + }
> + return 0;
> + }
This part actually worries me a bit. Yes, we can do it this way, but in general it sounds a bit more like we need a generic approach in hci_ldisc.c to handle pre-HCI firmware loading and/or setup.
In the btusb.c driver we added ->setup_on_usb callback. And for it sounds like we need something similar here. So that hci_ldisc.c can handle most of the basic TX/RX.
> +
> + if (!test_bit(HCI_UART_REGISTERED, &hu->flags))
> + return -EUNATCH;
> +
> + mrvl->rx_skb = h4_recv_buf(hu->hdev, mrvl->rx_skb, data, count,
> + mrvl_recv_pkts, ARRAY_SIZE(mrvl_recv_pkts));
> + if (IS_ERR(mrvl->rx_skb)) {
> + int err = PTR_ERR(mrvl->rx_skb);
> +
> + bt_dev_err(hu->hdev, "Frame reassembly failed (%d)", err);
> + mrvl->rx_skb = NULL;
> + return err;
> + }
> +
> + return count;
> +}
> +
> +static struct sk_buff *mrvl_dequeue(struct hci_uart *hu)
> +{
> + struct mrvl_data *mrvl = hu->priv;
> +
> + return skb_dequeue(&mrvl->txq);
> +}
> +
> +static int mrvl_init_fw_data(struct hci_uart *hu)
> +{
> + struct fw_data *fwdata;
> + struct mrvl_data *mrvl = hu->priv;
> +
> + fwdata = kzalloc(sizeof(*fwdata), GFP_KERNEL);
> +
This empty line here is not needed.
> + if (!fwdata)
> + return -ENOMEM;
> +
> + mrvl->fwdata = fwdata;
> + init_waitqueue_head(&fwdata->init_wait_q);
> +
> + return 0;
> +}
> +
> +/* Wait for the header from device */
> +static int mrvl_wait_for_hdr(struct hci_uart *hu, u8 header)
> +{
> + struct mrvl_data *mrvl = hu->priv;
> + struct fw_data *fw_data = mrvl->fwdata;
> +
> + fw_data->expected_ack = header;
> + fw_data->wait_fw = 0;
> +
> + if (!wait_event_interruptible_timeout(fw_data->init_wait_q,
> + fw_data->wait_fw,
> + ((MRVL_WAIT_TIMEOUT) * HZ / 1000))) {
Don't use HZ magic, use the proper conversation macros and define a new one specific for this value.
> + bt_dev_err(hu->hdev, "TIMEOUT, waiting for:0x%x",
> + fw_data->expected_ack);
> + return -1;
> + }
> +
> + return 0;
> +}
> +
> +/* Send bytes to device */
> +static int mrvl_send_data(struct hci_uart *hu, struct sk_buff *skb)
> +{
> + struct mrvl_data *mrvl = hu->priv;
> +
> + skb_queue_head(&mrvl->txq, skb);
> + hci_uart_tx_wakeup(hu);
> +
> + if (mrvl_wait_for_hdr(hu, MRVL_HDR_REQ_FW) == -1)
> + return -1;
> +
> + return 0;
> +}
> +
> +static struct sk_buff *mrvl_alloc_skb(struct hci_dev *hdev)
> +{
> + struct sk_buff *skb = NULL;
This assignment is useless.
> +
> + skb = bt_skb_alloc(MRVL_MAX_FW_BLOCK_SIZE, GFP_KERNEL);
> + if (!skb)
> + bt_dev_err(hdev, "cannot allocate memory for skb");
return NULL here please.
And you might want to check if we not have removed all the memory allocation error messages. I think the kernel will print appropriate errors by itself. Please follow general practice.
> + else
> + skb->dev = (void *)hdev;
> +
> + return skb;
> +}
> +
> +/* Download firmware to the device */
> +static int mrvl_dnld_fw(struct hci_uart *hu, const char *file_name)
> +{
> + struct hci_dev *hdev = hu->hdev;
> + const struct firmware *fw = NULL;
> + struct sk_buff *skb = NULL;
> + int offset = 0;
> + int ret, tx_len;
> + struct mrvl_data *mrvl = hu->priv;
> + struct fw_data *fw_data = mrvl->fwdata;
> +
> + ret = request_firmware(&fw, file_name, &hdev->dev);
> + if (ret < 0) {
> + bt_dev_err(hu->hdev, "request_firmware() failed");
> + return -1;
> + }
> +
> + bt_dev_info(hu->hdev, "Downloading FW (%d bytes)", (u16)fw->size);
> +
> + fw_data->last_ack = 0;
> +
> + do {
> + if ((offset >= fw->size) || (fw_data->last_ack))
> + break;
> + tx_len = fw_data->next_len;
> + if ((fw->size - offset) < tx_len)
> + tx_len = fw->size - offset;
> +
> + skb = mrvl_alloc_skb(hdev);
> + if (!skb) {
> + ret = -1;
> + goto done;
> + }
> +
> + memcpy(skb->data, &fw->data[offset], tx_len);
> + skb_put(skb, tx_len);
> + if (mrvl_send_data(hu, skb) != 0) {
> + bt_dev_err(hu->hdev, "fail to download firmware");
> + ret = -1;
> + goto done;
> + }
> + offset += tx_len;
> + } while (1);
> +
> + bt_dev_info(hu->hdev, "downloaded %d byte firmware", offset);
> +done:
> + release_firmware(fw);
> +
> + return ret;
> +}
> +
> +/* Set the baud rate */
> +static int mrvl_set_dev_baud(struct hci_uart *hu)
> +{
> + struct hci_dev *hdev = hu->hdev;
> + struct sk_buff *skb;
> + static const u8 baud_param[] = { 0xc0, 0xc6, 0x2d, 0x00 };
> + int err;
> +
> + skb = __hci_cmd_sync(hdev, MRVL_HCI_OP_SET_BAUD, sizeof(baud_param),
> + baud_param, HCI_INIT_TIMEOUT);
> + if (IS_ERR(skb)) {
> + err = PTR_ERR(skb);
> + bt_dev_err(hu->hdev, "Set device baudrate failed (%d)", err);
> + return err;
> + }
> + kfree_skb(skb);
> +
> + return 0;
> +}
> +
> +/* Reset device */
> +static int mrvl_reset(struct hci_uart *hu)
> +{
> + struct hci_dev *hdev = hu->hdev;
> + struct sk_buff *skb;
> + int err;
> +
> + skb = __hci_cmd_sync(hdev, HCI_OP_RESET, 0, NULL, HCI_CMD_TIMEOUT);
> + if (IS_ERR(skb)) {
> + err = PTR_ERR(skb);
> + bt_dev_err(hu->hdev, "Reset device failed (%d)", err);
> + return err;
> + }
> + kfree_skb(skb);
> +
> + return 0;
> +}
> +
> +static int mrvl_set_baud(struct hci_uart *hu)
> +{
> + int err;
> +
> + hci_uart_set_baudrate(hu, 115200);
> + hci_uart_set_flow_control(hu, false);
> +
> + err = mrvl_reset(hu);
> + if (err)
> + goto set_term_baud;
> + else
> + goto set_dev_baud;
> +
> +set_dev_baud:
> + err = mrvl_set_dev_baud(hu);
> + if (err)
> + return -1;
> +
> +set_term_baud:
> + hci_uart_set_baudrate(hu, 3000000);
> + hci_uart_set_flow_control(hu, false);
> +
> + return 0;
> +}
> +
> +static int mrvl_get_fw_name(struct hci_uart *hu, char *fw_name)
> +{
> + int ret;
> + struct mrvl_data *mrvl = hu->priv;
> + struct fw_data *fw_data = mrvl->fwdata;
> +
> + ret = mrvl_wait_for_hdr(hu, MRVL_HDR_CHIP_VER);
> + if (ret) {
> + ret = -1;
> + bt_dev_err(hu->hdev, "Could not read chip id and revision");
> + goto fail;
> + }
> +
> + bt_dev_dbg(hu->hdev, "chip_id=0x%x, chip_rev=0x%x",
> + fw_data->chip_id, fw_data->chip_rev);
> +
> + if (fw_data->chip_id == 0x50) {
> + memcpy(fw_name, MRVL_8997_FW_NAME, sizeof(MRVL_8997_FW_NAME));
> + } else {
> + ret = -1;
> + bt_dev_err(hu->hdev, "Invalid chip id");
> + }
Not a big fine of these else clauses. Check for the error and exit cleanly.
> +fail:
> + return ret;
> +}
> +
> +/* Download helper and firmare to device */
> +static int hci_uart_dnld_fw(struct hci_uart *hu)
> +{
> + struct tty_struct *tty = hu->tty;
> + struct ktermios new_termios;
> + struct ktermios old_termios;
> + struct mrvl_data *mrvl = hu->priv;
> + char fw_name[128];
> + int ret;
> +
> + old_termios = tty->termios;
> +
> + if (get_cts(hu)) {
> + bt_dev_info(hu->hdev, "fw is running");
> + clear_bit(HCI_UART_DNLD_FW, &mrvl->flags);
> + goto set_baud;
> + }
> +
> + hci_uart_set_baudrate(hu, 115200);
> + hci_uart_set_flow_control(hu, true);
> +
> + ret = mrvl_wait_for_hdr(hu, MRVL_HDR_REQ_FW);
> + if (ret)
> + goto fail;
> +
> + ret = mrvl_dnld_fw(hu, MRVL_HELPER_NAME);
> + if (ret)
> + goto fail;
> +
> + msleep(MRVL_DNLD_DELAY);
> +
> + hci_uart_set_baudrate(hu, 3000000);
> + hci_uart_set_flow_control(hu, false);
> +
> + ret = mrvl_get_fw_name(hu, fw_name);
> + if (ret)
> + goto fail;
> +
> + ret = mrvl_wait_for_hdr(hu, MRVL_HDR_REQ_FW);
> + if (ret)
> + goto fail;
> +
> + ret = mrvl_dnld_fw(hu, fw_name);
> + if (ret)
> + goto fail;
> +
> + msleep(MRVL_DNLD_DELAY);
> + /* restore uart settings */
> + new_termios = tty->termios;
> + tty->termios.c_cflag = old_termios.c_cflag;
> + tty_set_termios(tty, &new_termios);
> + clear_bit(HCI_UART_DNLD_FW, &mrvl->flags);
> +
> +set_baud:
> + ret = mrvl_set_baud(hu);
> + if (ret)
> + goto fail;
> +
> + msleep(MRVL_DNLD_DELAY);
> +
> + return ret;
> +fail:
> + /* restore uart settings */
> + new_termios = tty->termios;
> + tty->termios.c_cflag = old_termios.c_cflag;
> + tty_set_termios(tty, &new_termios);
> + clear_bit(HCI_UART_DNLD_FW, &mrvl->flags);
> +
> + return ret;
> +}
> +
> +static int mrvl_setup(struct hci_uart *hu)
> +{
> + struct mrvl_data *mrvl = hu->priv;
> +
> + mrvl_init_fw_data(hu);
> + set_bit(HCI_UART_DNLD_FW, &mrvl->flags);
> +
> + return hci_uart_dnld_fw(hu);
> +}
So this is clearly the wrong spot. When ->setup is called it is expected that HCI is ready. You are misusing it here.
> +
> +static const struct hci_uart_proto mrvlp = {
> + .id = HCI_UART_MRVL,
> + .name = "MRVL",
> + .open = mrvl_open,
> + .close = mrvl_close,
> + .recv = mrvl_recv,
> + .enqueue = mrvl_enqueue,
> + .dequeue = mrvl_dequeue,
> + .flush = mrvl_flush,
> + .setup = mrvl_setup,
> +};
> +
> +int __init mrvl_init(void)
> +{
> + return hci_uart_register_proto(&mrvlp);
> +}
> +
> +int __exit mrvl_deinit(void)
> +{
> + return hci_uart_unregister_proto(&mrvlp);
> +}
> diff --git a/drivers/bluetooth/hci_uart.h b/drivers/bluetooth/hci_uart.h
> index 4814ff0..8b1f744 100644
> --- a/drivers/bluetooth/hci_uart.h
> +++ b/drivers/bluetooth/hci_uart.h
> @@ -35,7 +35,7 @@
> #define HCIUARTGETFLAGS _IOR('U', 204, int)
>
> /* UART protocols */
> -#define HCI_UART_MAX_PROTO 10
> +#define HCI_UART_MAX_PROTO 11
>
> #define HCI_UART_H4 0
> #define HCI_UART_BCSP 1
> @@ -47,6 +47,7 @@
> #define HCI_UART_BCM 7
> #define HCI_UART_QCA 8
> #define HCI_UART_AG6XX 9
> +#define HCI_UART_MRVL 10
>
> #define HCI_UART_RAW_DEVICE 0
> #define HCI_UART_RESET_ON_INIT 1
> @@ -188,3 +189,8 @@ int qca_deinit(void);
> int ag6xx_init(void);
> int ag6xx_deinit(void);
> #endif
> +
> +#ifdef CONFIG_BT_HCIUART_MRVL
> +int mrvl_init(void);
> +int mrvl_deinit(void);
> +#endif
Regards
Marcel
Hi Marcel,
> From: Marcel Holtmann [mailto:[email protected]]
> Sent: Tuesday, April 12, 2016 9:48 PM
> To: Amitkumar Karwar
> Cc: [email protected]; Ganapathi Bhat
> Subject: Re: [PATCH v7] Bluetooth: hci_uart: Support firmware download
> for Marvell
>=20
> Hi Amitkumar,
>=20
> >> From: Amitkumar Karwar [mailto:[email protected]]
> >> Sent: Tuesday, April 05, 2016 2:04 PM
> >> To: [email protected]
> >> Cc: [email protected]; Ganapathi Bhat; Amitkumar Karwar
> >> Subject: [PATCH v7] Bluetooth: hci_uart: Support firmware download
> >> for Marvell
> >>
> >> From: Ganapathi Bhat <[email protected]>
> >>
> >> This patch implement firmware download feature for Marvell Bluetooth
> >> devices. If firmware is already downloaded, it will skip downloading.
> >>
> >> Signed-off-by: Ganapathi Bhat <[email protected]>
> >> Signed-off-by: Amitkumar Karwar <[email protected]>
> >> ---
> >> v2: Fixed compilation warning reported by kbuild test robot
> >> v3: Addressed review comments from Marcel Holtmann
> >> a) Removed vendor specific code from hci_ldisc.c
> >> b) Get rid of static forward declaration
> >> c) Removed unnecessary heavy nesting
> >> d) Git rid of module parameter and global variables
> >> e) Add logic to pick right firmware image
> >> v4: Addresses review comments from Alan
> >> a) Use existing kernel helper APIs instead of writing own.
> >> b) Replace mdelay() with msleep()
> >> v5: Addresses review comments from Loic Poulain
> >> a) Use bt_dev_err/warn/dbg helpers insted of BT_ERR/WARN/DBG
> >> b) Used static functions where required and removed forward
> >> delcarations
> >> c) Edited comments for the function hci_uart_recv_data
> >> d) Made HCI_UART_DNLD_FW flag a part of driver private data
> >> v6: Addresses review comments from Loic Poulain
> >> a) Used skb instead of array to store firmware data during
> download
> >> b) Used hci_uart_tx_wakeup and enqueued packets instead of tty
> write
> >> c) Used GFP_KERNEL instead of GFP_ATOMIC
> >> v7: Edited Kconfig to add dependency for BT_HCIUART_H4. The change
> >> resolves
> >> errors reported by kbuild test robot.
> >> ---
> >> drivers/bluetooth/Kconfig | 11 +
> >> drivers/bluetooth/Makefile | 1 +
> >> drivers/bluetooth/btmrvl.h | 43 ++++
> >> drivers/bluetooth/hci_ldisc.c | 6 +
> >> drivers/bluetooth/hci_mrvl.c | 568
> >> ++++++++++++++++++++++++++++++++++++++++++
> >> drivers/bluetooth/hci_uart.h | 8 +-
> >> 6 files changed, 636 insertions(+), 1 deletion(-) create mode 100644
> >> drivers/bluetooth/btmrvl.h create mode 100644
> >> drivers/bluetooth/hci_mrvl.c
> >>
> >
> > Could you please take this patch if there are no further
> comments/suggestions?
>=20
> didn't I see a kbot build warning for this version as well? Or was that
> the previous version?
>=20
Last kbot build warning was for V6 patch. It has been fixed in this version=
.
https://lkml.org/lkml/2016/4/2/102
Regards,
Amitkumar
Hi Amitkumar,
>> From: Amitkumar Karwar [mailto:[email protected]]
>> Sent: Tuesday, April 05, 2016 2:04 PM
>> To: [email protected]
>> Cc: [email protected]; Ganapathi Bhat; Amitkumar Karwar
>> Subject: [PATCH v7] Bluetooth: hci_uart: Support firmware download for
>> Marvell
>>
>> From: Ganapathi Bhat <[email protected]>
>>
>> This patch implement firmware download feature for Marvell Bluetooth
>> devices. If firmware is already downloaded, it will skip downloading.
>>
>> Signed-off-by: Ganapathi Bhat <[email protected]>
>> Signed-off-by: Amitkumar Karwar <[email protected]>
>> ---
>> v2: Fixed compilation warning reported by kbuild test robot
>> v3: Addressed review comments from Marcel Holtmann
>> a) Removed vendor specific code from hci_ldisc.c
>> b) Get rid of static forward declaration
>> c) Removed unnecessary heavy nesting
>> d) Git rid of module parameter and global variables
>> e) Add logic to pick right firmware image
>> v4: Addresses review comments from Alan
>> a) Use existing kernel helper APIs instead of writing own.
>> b) Replace mdelay() with msleep()
>> v5: Addresses review comments from Loic Poulain
>> a) Use bt_dev_err/warn/dbg helpers insted of BT_ERR/WARN/DBG
>> b) Used static functions where required and removed forward
>> delcarations
>> c) Edited comments for the function hci_uart_recv_data
>> d) Made HCI_UART_DNLD_FW flag a part of driver private data
>> v6: Addresses review comments from Loic Poulain
>> a) Used skb instead of array to store firmware data during download
>> b) Used hci_uart_tx_wakeup and enqueued packets instead of tty write
>> c) Used GFP_KERNEL instead of GFP_ATOMIC
>> v7: Edited Kconfig to add dependency for BT_HCIUART_H4. The change
>> resolves
>> errors reported by kbuild test robot.
>> ---
>> drivers/bluetooth/Kconfig | 11 +
>> drivers/bluetooth/Makefile | 1 +
>> drivers/bluetooth/btmrvl.h | 43 ++++
>> drivers/bluetooth/hci_ldisc.c | 6 +
>> drivers/bluetooth/hci_mrvl.c | 568
>> ++++++++++++++++++++++++++++++++++++++++++
>> drivers/bluetooth/hci_uart.h | 8 +-
>> 6 files changed, 636 insertions(+), 1 deletion(-) create mode 100644
>> drivers/bluetooth/btmrvl.h create mode 100644
>> drivers/bluetooth/hci_mrvl.c
>>
>
> Could you please take this patch if there are no further comments/suggestions?
didn't I see a kbot build warning for this version as well? Or was that the previous version?
Regards
Marcel
Hi Marcel,
> From: Amitkumar Karwar [mailto:[email protected]]
> Sent: Tuesday, April 05, 2016 2:04 PM
> To: [email protected]
> Cc: [email protected]; Ganapathi Bhat; Amitkumar Karwar
> Subject: [PATCH v7] Bluetooth: hci_uart: Support firmware download for
> Marvell
>
> From: Ganapathi Bhat <[email protected]>
>
> This patch implement firmware download feature for Marvell Bluetooth
> devices. If firmware is already downloaded, it will skip downloading.
>
> Signed-off-by: Ganapathi Bhat <[email protected]>
> Signed-off-by: Amitkumar Karwar <[email protected]>
> ---
> v2: Fixed compilation warning reported by kbuild test robot
> v3: Addressed review comments from Marcel Holtmann
> a) Removed vendor specific code from hci_ldisc.c
> b) Get rid of static forward declaration
> c) Removed unnecessary heavy nesting
> d) Git rid of module parameter and global variables
> e) Add logic to pick right firmware image
> v4: Addresses review comments from Alan
> a) Use existing kernel helper APIs instead of writing own.
> b) Replace mdelay() with msleep()
> v5: Addresses review comments from Loic Poulain
> a) Use bt_dev_err/warn/dbg helpers insted of BT_ERR/WARN/DBG
> b) Used static functions where required and removed forward
> delcarations
> c) Edited comments for the function hci_uart_recv_data
> d) Made HCI_UART_DNLD_FW flag a part of driver private data
> v6: Addresses review comments from Loic Poulain
> a) Used skb instead of array to store firmware data during download
> b) Used hci_uart_tx_wakeup and enqueued packets instead of tty write
> c) Used GFP_KERNEL instead of GFP_ATOMIC
> v7: Edited Kconfig to add dependency for BT_HCIUART_H4. The change
> resolves
> errors reported by kbuild test robot.
> ---
> drivers/bluetooth/Kconfig | 11 +
> drivers/bluetooth/Makefile | 1 +
> drivers/bluetooth/btmrvl.h | 43 ++++
> drivers/bluetooth/hci_ldisc.c | 6 +
> drivers/bluetooth/hci_mrvl.c | 568
> ++++++++++++++++++++++++++++++++++++++++++
> drivers/bluetooth/hci_uart.h | 8 +-
> 6 files changed, 636 insertions(+), 1 deletion(-) create mode 100644
> drivers/bluetooth/btmrvl.h create mode 100644
> drivers/bluetooth/hci_mrvl.c
>
Could you please take this patch if there are no further comments/suggestions?
Regards,
Amitkumar