This patch adds basic SoC support for Mediatek's new 4-core SoC,
MT7986, which is mainly for wifi-router application.
---
v3: updated mt7986 pinctrl releated dt-bindig,
updated mt7986 pinctrl driver according to reviewers's suggestion
fixed wrong clock ID in mt7986-clock-IDs
added Acked-by tag in some patches
v2: updated mt7986 clock releated IDs, dt-binding, and driver
updated mt7986 clock releated dt-binding and driver
updated device tree of mt7986a and mt7986b
Sam Shih (9):
dt-bindings: clock: mediatek: document clk bindings for mediatek
mt7986 SoC
clk: mediatek: add mt7986 clock IDs
clk: mediatek: add mt7986 clock support
pinctrl: mediatek: moore: check if pin_desc is valid before use
dt-bindings: pinctrl: update bindings for MT7986 SoC
pinctrl: mediatek: add support for MT7986 SoC
dt-bindings: arm64: dts: mediatek: Add mt7986 series
arm64: dts: mediatek: add mt7986a support
arm64: dts: mediatek: add mt7986b support
.../devicetree/bindings/arm/mediatek.yaml | 8 +
.../arm/mediatek/mediatek,apmixedsys.txt | 1 +
.../bindings/arm/mediatek/mediatek,ethsys.txt | 1 +
.../arm/mediatek/mediatek,infracfg.txt | 1 +
.../arm/mediatek/mediatek,sgmiisys.txt | 2 +
.../arm/mediatek/mediatek,topckgen.txt | 1 +
.../pinctrl/mediatek,mt7986-pinctrl.txt | 300 ++++++
arch/arm64/boot/dts/mediatek/Makefile | 2 +
arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 49 +
arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 227 +++++
arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts | 21 +
arch/arm64/boot/dts/mediatek/mt7986b.dtsi | 227 +++++
drivers/clk/mediatek/Kconfig | 17 +
drivers/clk/mediatek/Makefile | 4 +
drivers/clk/mediatek/clk-mt7986-apmixed.c | 78 ++
drivers/clk/mediatek/clk-mt7986-eth.c | 132 +++
drivers/clk/mediatek/clk-mt7986-infracfg.c | 198 ++++
drivers/clk/mediatek/clk-mt7986-topckgen.c | 319 ++++++
drivers/pinctrl/mediatek/Kconfig | 7 +
drivers/pinctrl/mediatek/Makefile | 1 +
drivers/pinctrl/mediatek/pinctrl-moore.c | 18 +
drivers/pinctrl/mediatek/pinctrl-mt7986.c | 928 ++++++++++++++++++
include/dt-bindings/clock/mt7986-clk.h | 169 ++++
23 files changed, 2711 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.txt
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a.dtsi
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986b.dtsi
create mode 100644 drivers/clk/mediatek/clk-mt7986-apmixed.c
create mode 100644 drivers/clk/mediatek/clk-mt7986-eth.c
create mode 100644 drivers/clk/mediatek/clk-mt7986-infracfg.c
create mode 100644 drivers/clk/mediatek/clk-mt7986-topckgen.c
create mode 100644 drivers/pinctrl/mediatek/pinctrl-mt7986.c
create mode 100644 include/dt-bindings/clock/mt7986-clk.h
--
2.29.2
Add MT7986 clock dt-bindings, include topckgen, apmixedsys,
infracfg, and ethernet subsystem clocks.
Signed-off-by: Sam Shih <[email protected]>
Acked-by: Rob Herring <[email protected]>
---
v3: Fixed SGMII wrong ID and added an Acked-by tag
v2: changed to dual licience
applied the comment suggested by reviewers:
- removed 1:1 factor clock
- renamed factor clock for easier to understand
---
include/dt-bindings/clock/mt7986-clk.h | 169 +++++++++++++++++++++++++
1 file changed, 169 insertions(+)
create mode 100644 include/dt-bindings/clock/mt7986-clk.h
diff --git a/include/dt-bindings/clock/mt7986-clk.h b/include/dt-bindings/clock/mt7986-clk.h
new file mode 100644
index 000000000000..5a9b169324b0
--- /dev/null
+++ b/include/dt-bindings/clock/mt7986-clk.h
@@ -0,0 +1,169 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (c) 2021 MediaTek Inc.
+ * Author: Sam Shih <[email protected]>
+ */
+
+#ifndef _DT_BINDINGS_CLK_MT7986_H
+#define _DT_BINDINGS_CLK_MT7986_H
+
+/* APMIXEDSYS */
+
+#define CLK_APMIXED_ARMPLL 0
+#define CLK_APMIXED_NET2PLL 1
+#define CLK_APMIXED_MMPLL 2
+#define CLK_APMIXED_SGMPLL 3
+#define CLK_APMIXED_WEDMCUPLL 4
+#define CLK_APMIXED_NET1PLL 5
+#define CLK_APMIXED_MPLL 6
+#define CLK_APMIXED_APLL2 7
+
+/* TOPCKGEN */
+
+#define CLK_TOP_XTAL 0
+#define CLK_TOP_XTAL_D2 1
+#define CLK_TOP_RTC_32K 2
+#define CLK_TOP_RTC_32P7K 3
+#define CLK_TOP_MPLL_D2 4
+#define CLK_TOP_MPLL_D4 5
+#define CLK_TOP_MPLL_D8 6
+#define CLK_TOP_MPLL_D8_D2 7
+#define CLK_TOP_MPLL_D3_D2 8
+#define CLK_TOP_MMPLL_D2 9
+#define CLK_TOP_MMPLL_D4 10
+#define CLK_TOP_MMPLL_D8 11
+#define CLK_TOP_MMPLL_D8_D2 12
+#define CLK_TOP_MMPLL_D3_D8 13
+#define CLK_TOP_MMPLL_U2PHY 14
+#define CLK_TOP_APLL2_D4 15
+#define CLK_TOP_NET1PLL_D4 16
+#define CLK_TOP_NET1PLL_D5 17
+#define CLK_TOP_NET1PLL_D5_D2 18
+#define CLK_TOP_NET1PLL_D5_D4 19
+#define CLK_TOP_NET1PLL_D8_D2 20
+#define CLK_TOP_NET1PLL_D8_D4 21
+#define CLK_TOP_NET2PLL_D4 22
+#define CLK_TOP_NET2PLL_D4_D2 23
+#define CLK_TOP_NET2PLL_D3_D2 24
+#define CLK_TOP_WEDMCUPLL_D5_D2 25
+#define CLK_TOP_NFI1X_SEL 26
+#define CLK_TOP_SPINFI_SEL 27
+#define CLK_TOP_SPI_SEL 28
+#define CLK_TOP_SPIM_MST_SEL 29
+#define CLK_TOP_UART_SEL 30
+#define CLK_TOP_PWM_SEL 31
+#define CLK_TOP_I2C_SEL 32
+#define CLK_TOP_PEXTP_TL_SEL 33
+#define CLK_TOP_EMMC_250M_SEL 34
+#define CLK_TOP_EMMC_416M_SEL 35
+#define CLK_TOP_F_26M_ADC_SEL 36
+#define CLK_TOP_DRAMC_SEL 37
+#define CLK_TOP_DRAMC_MD32_SEL 38
+#define CLK_TOP_SYSAXI_SEL 39
+#define CLK_TOP_SYSAPB_SEL 40
+#define CLK_TOP_ARM_DB_MAIN_SEL 41
+#define CLK_TOP_ARM_DB_JTSEL 42
+#define CLK_TOP_NETSYS_SEL 43
+#define CLK_TOP_NETSYS_500M_SEL 44
+#define CLK_TOP_NETSYS_MCU_SEL 45
+#define CLK_TOP_NETSYS_2X_SEL 46
+#define CLK_TOP_SGM_325M_SEL 47
+#define CLK_TOP_SGM_REG_SEL 48
+#define CLK_TOP_A1SYS_SEL 49
+#define CLK_TOP_CONN_MCUSYS_SEL 50
+#define CLK_TOP_EIP_B_SEL 51
+#define CLK_TOP_PCIE_PHY_SEL 52
+#define CLK_TOP_USB3_PHY_SEL 53
+#define CLK_TOP_F26M_SEL 54
+#define CLK_TOP_AUD_L_SEL 55
+#define CLK_TOP_A_TUNER_SEL 56
+#define CLK_TOP_U2U3_SEL 57
+#define CLK_TOP_U2U3_SYS_SEL 58
+#define CLK_TOP_U2U3_XHCI_SEL 59
+#define CLK_TOP_DA_U2_REFSEL 60
+#define CLK_TOP_DA_U2_CK_1P_SEL 61
+#define CLK_TOP_AP2CNN_HOST_SEL 62
+#define CLK_TOP_JTAG 63
+
+/* INFRACFG */
+
+#define CLK_INFRA_SYSAXI_D2 0
+#define CLK_INFRA_UART0_SEL 1
+#define CLK_INFRA_UART1_SEL 2
+#define CLK_INFRA_UART2_SEL 3
+#define CLK_INFRA_SPI0_SEL 4
+#define CLK_INFRA_SPI1_SEL 5
+#define CLK_INFRA_PWM1_SEL 6
+#define CLK_INFRA_PWM2_SEL 7
+#define CLK_INFRA_PWM_BSEL 8
+#define CLK_INFRA_PCIE_SEL 9
+#define CLK_INFRA_GPT_STA 10
+#define CLK_INFRA_PWM_HCK 11
+#define CLK_INFRA_PWM_STA 12
+#define CLK_INFRA_PWM1_CK 13
+#define CLK_INFRA_PWM2_CK 14
+#define CLK_INFRA_CQ_DMA_CK 15
+#define CLK_INFRA_EIP97_CK 16
+#define CLK_INFRA_AUD_BUS_CK 17
+#define CLK_INFRA_AUD_26M_CK 18
+#define CLK_INFRA_AUD_L_CK 19
+#define CLK_INFRA_AUD_AUD_CK 20
+#define CLK_INFRA_AUD_EG2_CK 21
+#define CLK_INFRA_DRAMC_26M_CK 22
+#define CLK_INFRA_DBG_CK 23
+#define CLK_INFRA_AP_DMA_CK 24
+#define CLK_INFRA_SEJ_CK 25
+#define CLK_INFRA_SEJ_13M_CK 26
+#define CLK_INFRA_THERM_CK 27
+#define CLK_INFRA_I2C0_CK 28
+#define CLK_INFRA_UART0_CK 29
+#define CLK_INFRA_UART1_CK 30
+#define CLK_INFRA_UART2_CK 31
+#define CLK_INFRA_NFI1_CK 32
+#define CLK_INFRA_SPINFI1_CK 33
+#define CLK_INFRA_NFI_HCK_CK 34
+#define CLK_INFRA_SPI0_CK 35
+#define CLK_INFRA_SPI1_CK 36
+#define CLK_INFRA_SPI0_HCK_CK 37
+#define CLK_INFRA_SPI1_HCK_CK 38
+#define CLK_INFRA_FRTC_CK 39
+#define CLK_INFRA_MSDC_CK 40
+#define CLK_INFRA_MSDC_HCK_CK 41
+#define CLK_INFRA_MSDC_133M_CK 42
+#define CLK_INFRA_MSDC_66M_CK 43
+#define CLK_INFRA_ADC_26M_CK 44
+#define CLK_INFRA_ADC_FRC_CK 45
+#define CLK_INFRA_FBIST2FPC_CK 46
+#define CLK_INFRA_IUSB_133_CK 47
+#define CLK_INFRA_IUSB_66M_CK 48
+#define CLK_INFRA_IUSB_SYS_CK 49
+#define CLK_INFRA_IUSB_CK 50
+#define CLK_INFRA_IPCIE_CK 51
+#define CLK_INFRA_IPCIE_PIPE_CK 52
+#define CLK_INFRA_IPCIER_CK 53
+#define CLK_INFRA_IPCIEB_CK 54
+#define CLK_INFRA_TRNG_CK 55
+
+/* SGMIISYS_0 */
+
+#define CLK_SGMII0_TX250M_EN 0
+#define CLK_SGMII0_RX250M_EN 1
+#define CLK_SGMII0_CDR_REF 2
+#define CLK_SGMII0_CDR_FB 3
+
+/* SGMIISYS_1 */
+
+#define CLK_SGMII1_TX250M_EN 0
+#define CLK_SGMII1_RX250M_EN 1
+#define CLK_SGMII1_CDR_REF 2
+#define CLK_SGMII1_CDR_FB 3
+
+/* ETHSYS */
+
+#define CLK_ETH_FE_EN 0
+#define CLK_ETH_GP2_EN 1
+#define CLK_ETH_GP1_EN 2
+#define CLK_ETH_WOCPU1_EN 3
+#define CLK_ETH_WOCPU0_EN 4
+
+#endif /* _DT_BINDINGS_CLK_MT7986_H */
--
2.29.2
Add MT7986 clock support, include topckgen, apmixedsys,
infracfg, and ethernet subsystem clocks.
Signed-off-by: Sam Shih <[email protected]>
---
v2: applied the comment suggested by reviewers:
- splited basic clock driver to apmixed, topckgen, and infracfg
- removed 1:1 factor clock
- renamed factor clock for easier to understand
---
drivers/clk/mediatek/Kconfig | 17 ++
drivers/clk/mediatek/Makefile | 4 +
drivers/clk/mediatek/clk-mt7986-apmixed.c | 78 +++++
drivers/clk/mediatek/clk-mt7986-eth.c | 132 +++++++++
drivers/clk/mediatek/clk-mt7986-infracfg.c | 198 +++++++++++++
drivers/clk/mediatek/clk-mt7986-topckgen.c | 319 +++++++++++++++++++++
6 files changed, 748 insertions(+)
create mode 100644 drivers/clk/mediatek/clk-mt7986-apmixed.c
create mode 100644 drivers/clk/mediatek/clk-mt7986-eth.c
create mode 100644 drivers/clk/mediatek/clk-mt7986-infracfg.c
create mode 100644 drivers/clk/mediatek/clk-mt7986-topckgen.c
diff --git a/drivers/clk/mediatek/Kconfig b/drivers/clk/mediatek/Kconfig
index 439b7c8d0d07..f5f0c0c1012a 100644
--- a/drivers/clk/mediatek/Kconfig
+++ b/drivers/clk/mediatek/Kconfig
@@ -344,6 +344,23 @@ config COMMON_CLK_MT7629_HIFSYS
This driver supports MediaTek MT7629 HIFSYS clocks providing
to PCI-E and USB.
+config COMMON_CLK_MT7986
+ bool "Clock driver for MediaTek MT7986"
+ depends on ARCH_MEDIATEK || COMPILE_TEST
+ select COMMON_CLK_MEDIATEK
+ default ARCH_MEDIATEK
+ help
+ This driver supports MediaTek MT7986 basic clocks and clocks
+ required for various periperals found on MediaTek.
+
+config COMMON_CLK_MT7986_ETHSYS
+ bool "Clock driver for MediaTek MT7986 ETHSYS"
+ depends on COMMON_CLK_MT7986
+ default COMMON_CLK_MT7986
+ help
+ This driver add support for clocks for Ethernet and SGMII
+ required on MediaTek MT7986 SoC.
+
config COMMON_CLK_MT8135
bool "Clock driver for MediaTek MT8135"
depends on (ARCH_MEDIATEK && ARM) || COMPILE_TEST
diff --git a/drivers/clk/mediatek/Makefile b/drivers/clk/mediatek/Makefile
index 15bc045f0b71..fec514413c98 100644
--- a/drivers/clk/mediatek/Makefile
+++ b/drivers/clk/mediatek/Makefile
@@ -46,6 +46,10 @@ obj-$(CONFIG_COMMON_CLK_MT7622_AUDSYS) += clk-mt7622-aud.o
obj-$(CONFIG_COMMON_CLK_MT7629) += clk-mt7629.o
obj-$(CONFIG_COMMON_CLK_MT7629_ETHSYS) += clk-mt7629-eth.o
obj-$(CONFIG_COMMON_CLK_MT7629_HIFSYS) += clk-mt7629-hif.o
+obj-$(CONFIG_COMMON_CLK_MT7986) += clk-mt7986-apmixed.o
+obj-$(CONFIG_COMMON_CLK_MT7986) += clk-mt7986-topckgen.o
+obj-$(CONFIG_COMMON_CLK_MT7986) += clk-mt7986-infracfg.o
+obj-$(CONFIG_COMMON_CLK_MT7986_ETHSYS) += clk-mt7986-eth.o
obj-$(CONFIG_COMMON_CLK_MT8135) += clk-mt8135.o
obj-$(CONFIG_COMMON_CLK_MT8167) += clk-mt8167.o
obj-$(CONFIG_COMMON_CLK_MT8167_AUDSYS) += clk-mt8167-aud.o
diff --git a/drivers/clk/mediatek/clk-mt7986-apmixed.c b/drivers/clk/mediatek/clk-mt7986-apmixed.c
new file mode 100644
index 000000000000..0925d61b55f2
--- /dev/null
+++ b/drivers/clk/mediatek/clk-mt7986-apmixed.c
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: GPL-1.0
+/*
+ * Copyright (c) 2021 MediaTek Inc.
+ * Author: Sam Shih <[email protected]>
+ * Author: Wenzhen Yu <[email protected]>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include "clk-mtk.h"
+#include "clk-gate.h"
+#include "clk-mux.h"
+
+#include <dt-bindings/clock/mt7986-clk.h>
+#include <linux/clk.h>
+
+#define MT7986_PLL_FMAX (2500UL * MHZ)
+#define CON0_MT7986_RST_BAR BIT(27)
+
+#define PLL_xtal(_id, _name, _reg, _pwr_reg, _en_mask, _flags, _pcwbits, \
+ _pd_reg, _pd_shift, _tuner_reg, _pcw_reg, _pcw_shift, \
+ _div_table, _parent_name) \
+ { \
+ .id = _id, .name = _name, .reg = _reg, .pwr_reg = _pwr_reg, \
+ .en_mask = _en_mask, .flags = _flags, \
+ .rst_bar_mask = CON0_MT7986_RST_BAR, .fmax = MT7986_PLL_FMAX, \
+ .pcwbits = _pcwbits, .pd_reg = _pd_reg, .pd_shift = _pd_shift, \
+ .tuner_reg = _tuner_reg, .pcw_reg = _pcw_reg, \
+ .pcw_shift = _pcw_shift, .div_table = _div_table, \
+ .parent_name = _parent_name, \
+ }
+
+#define PLL(_id, _name, _reg, _pwr_reg, _en_mask, _flags, _pcwbits, _pd_reg, \
+ _pd_shift, _tuner_reg, _pcw_reg, _pcw_shift) \
+ PLL_xtal(_id, _name, _reg, _pwr_reg, _en_mask, _flags, _pcwbits, \
+ _pd_reg, _pd_shift, _tuner_reg, _pcw_reg, _pcw_shift, NULL, \
+ "clkxtal")
+
+static const struct mtk_pll_data plls[] = {
+ PLL(CLK_APMIXED_ARMPLL, "armpll", 0x0200, 0x020C, 0x00000001, 0, 32,
+ 0x0200, 4, 0, 0x0204, 0),
+ PLL(CLK_APMIXED_NET2PLL, "net2pll", 0x0210, 0x021C, 0x00000001, 0, 32,
+ 0x0210, 4, 0, 0x0214, 0),
+ PLL(CLK_APMIXED_MMPLL, "mmpll", 0x0220, 0x022C, 0x00000001, 0, 32,
+ 0x0220, 4, 0, 0x0224, 0),
+ PLL(CLK_APMIXED_SGMPLL, "sgmpll", 0x0230, 0x023c, 0x00000001, 0, 32,
+ 0x0230, 4, 0, 0x0234, 0),
+ PLL(CLK_APMIXED_WEDMCUPLL, "wedmcupll", 0x0240, 0x024c, 0x00000001, 0,
+ 32, 0x0240, 4, 0, 0x0244, 0),
+ PLL(CLK_APMIXED_NET1PLL, "net1pll", 0x0250, 0x025c, 0x00000001, 0, 32,
+ 0x0250, 4, 0, 0x0254, 0),
+ PLL(CLK_APMIXED_MPLL, "mpll", 0x0260, 0x0270, 0x00000001, 0, 32, 0x0260,
+ 4, 0, 0x0264, 0),
+ PLL(CLK_APMIXED_APLL2, "apll2", 0x0278, 0x0288, 0x00000001, 0, 32,
+ 0x0278, 4, 0, 0x027c, 0),
+};
+
+static void __init mtk_apmixedsys_init(struct device_node *node)
+{
+ struct clk_onecell_data *clk_data;
+ int r;
+
+ clk_data = mtk_alloc_clk_data(ARRAY_SIZE(plls));
+
+ mtk_clk_register_plls(node, plls, ARRAY_SIZE(plls), clk_data);
+
+ clk_prepare_enable(clk_data->clks[CLK_APMIXED_ARMPLL]);
+
+ r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);
+ if (r)
+ pr_err("%s(): could not register clock provider: %d\n",
+ __func__, r);
+}
+CLK_OF_DECLARE(mtk_apmixedsys, "mediatek,mt7986-apmixedsys",
+ mtk_apmixedsys_init);
diff --git a/drivers/clk/mediatek/clk-mt7986-eth.c b/drivers/clk/mediatek/clk-mt7986-eth.c
new file mode 100644
index 000000000000..495d023ccad7
--- /dev/null
+++ b/drivers/clk/mediatek/clk-mt7986-eth.c
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2021 MediaTek Inc.
+ * Author: Sam Shih <[email protected]>
+ * Author: Wenzhen Yu <[email protected]>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+
+#include "clk-mtk.h"
+#include "clk-gate.h"
+
+#include <dt-bindings/clock/mt7986-clk.h>
+
+static const struct mtk_gate_regs sgmii0_cg_regs = {
+ .set_ofs = 0xe4,
+ .clr_ofs = 0xe4,
+ .sta_ofs = 0xe4,
+};
+
+#define GATE_SGMII0(_id, _name, _parent, _shift) \
+ { \
+ .id = _id, .name = _name, .parent_name = _parent, \
+ .regs = &sgmii0_cg_regs, .shift = _shift, \
+ .ops = &mtk_clk_gate_ops_no_setclr_inv, \
+ }
+
+static const struct mtk_gate sgmii0_clks[] __initconst = {
+ GATE_SGMII0(CLK_SGMII0_TX250M_EN, "sgmii0_tx250m_en", "top_xtal", 2),
+ GATE_SGMII0(CLK_SGMII0_RX250M_EN, "sgmii0_rx250m_en", "top_xtal", 3),
+ GATE_SGMII0(CLK_SGMII0_CDR_REF, "sgmii0_cdr_ref", "top_xtal", 4),
+ GATE_SGMII0(CLK_SGMII0_CDR_FB, "sgmii0_cdr_fb", "top_xtal", 5),
+};
+
+static const struct mtk_gate_regs sgmii1_cg_regs = {
+ .set_ofs = 0xe4,
+ .clr_ofs = 0xe4,
+ .sta_ofs = 0xe4,
+};
+
+#define GATE_SGMII1(_id, _name, _parent, _shift) \
+ { \
+ .id = _id, .name = _name, .parent_name = _parent, \
+ .regs = &sgmii1_cg_regs, .shift = _shift, \
+ .ops = &mtk_clk_gate_ops_no_setclr_inv, \
+ }
+
+static const struct mtk_gate sgmii1_clks[] __initconst = {
+ GATE_SGMII1(CLK_SGMII1_TX250M_EN, "sgmii1_tx250m_en", "top_xtal", 2),
+ GATE_SGMII1(CLK_SGMII1_RX250M_EN, "sgmii1_rx250m_en", "top_xtal", 3),
+ GATE_SGMII1(CLK_SGMII1_CDR_REF, "sgmii1_cdr_ref", "top_xtal", 4),
+ GATE_SGMII1(CLK_SGMII1_CDR_FB, "sgmii1_cdr_fb", "top_xtal", 5),
+};
+
+static const struct mtk_gate_regs eth_cg_regs = {
+ .set_ofs = 0x30,
+ .clr_ofs = 0x30,
+ .sta_ofs = 0x30,
+};
+
+#define GATE_ETH(_id, _name, _parent, _shift) \
+ { \
+ .id = _id, .name = _name, .parent_name = _parent, \
+ .regs = ð_cg_regs, .shift = _shift, \
+ .ops = &mtk_clk_gate_ops_no_setclr_inv, \
+ }
+
+static const struct mtk_gate eth_clks[] __initconst = {
+ GATE_ETH(CLK_ETH_FE_EN, "eth_fe_en", "netsys_2x_sel", 6),
+ GATE_ETH(CLK_ETH_GP2_EN, "eth_gp2_en", "sgm_325m_sel", 7),
+ GATE_ETH(CLK_ETH_GP1_EN, "eth_gp1_en", "sgm_325m_sel", 8),
+ GATE_ETH(CLK_ETH_WOCPU1_EN, "eth_wocpu1_en", "netsys_mcu_sel", 14),
+ GATE_ETH(CLK_ETH_WOCPU0_EN, "eth_wocpu0_en", "netsys_mcu_sel", 15),
+};
+
+static void __init mtk_sgmiisys_0_init(struct device_node *node)
+{
+ struct clk_onecell_data *clk_data;
+ int r;
+
+ clk_data = mtk_alloc_clk_data(ARRAY_SIZE(sgmii0_clks));
+
+ mtk_clk_register_gates(node, sgmii0_clks, ARRAY_SIZE(sgmii0_clks),
+ clk_data);
+
+ r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);
+ if (r)
+ pr_err("%s(): could not register clock provider: %d\n",
+ __func__, r);
+}
+CLK_OF_DECLARE(mtk_sgmiisys_0, "mediatek,mt7986-sgmiisys_0",
+ mtk_sgmiisys_0_init);
+
+static void __init mtk_sgmiisys_1_init(struct device_node *node)
+{
+ struct clk_onecell_data *clk_data;
+ int r;
+
+ clk_data = mtk_alloc_clk_data(ARRAY_SIZE(sgmii1_clks));
+
+ mtk_clk_register_gates(node, sgmii1_clks, ARRAY_SIZE(sgmii1_clks),
+ clk_data);
+
+ r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);
+
+ if (r)
+ pr_err("%s(): could not register clock provider: %d\n",
+ __func__, r);
+}
+CLK_OF_DECLARE(mtk_sgmiisys_1, "mediatek,mt7986-sgmiisys_1",
+ mtk_sgmiisys_1_init);
+
+static void __init mtk_ethsys_init(struct device_node *node)
+{
+ struct clk_onecell_data *clk_data;
+ int r;
+
+ clk_data = mtk_alloc_clk_data(ARRAY_SIZE(eth_clks));
+
+ mtk_clk_register_gates(node, eth_clks, ARRAY_SIZE(eth_clks), clk_data);
+
+ r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);
+
+ if (r)
+ pr_err("%s(): could not register clock provider: %d\n",
+ __func__, r);
+}
+CLK_OF_DECLARE(mtk_ethsys, "mediatek,mt7986-ethsys_ck", mtk_ethsys_init);
diff --git a/drivers/clk/mediatek/clk-mt7986-infracfg.c b/drivers/clk/mediatek/clk-mt7986-infracfg.c
new file mode 100644
index 000000000000..35e16c28966a
--- /dev/null
+++ b/drivers/clk/mediatek/clk-mt7986-infracfg.c
@@ -0,0 +1,198 @@
+// SPDX-License-Identifier: GPL-1.0
+/*
+ * Copyright (c) 2021 MediaTek Inc.
+ * Author: Sam Shih <[email protected]>
+ * Author: Wenzhen Yu <[email protected]>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include "clk-mtk.h"
+#include "clk-gate.h"
+#include "clk-mux.h"
+
+#include <dt-bindings/clock/mt7986-clk.h>
+#include <linux/clk.h>
+
+static DEFINE_SPINLOCK(mt7986_clk_lock);
+
+static const struct mtk_fixed_factor infra_divs[] __initconst = {
+ FACTOR(CLK_INFRA_SYSAXI_D2, "infra_sysaxi_d2", "sysaxi_sel", 1, 2),
+};
+
+static const char *const infra_uart_parent[] __initconst = { "csw_f26m_sel",
+ "uart_sel" };
+
+static const char *const infra_spi_parents[] __initconst = { "i2c_sel",
+ "spi_sel" };
+
+static const char *const infra_pwm_bsel_parents[] __initconst = {
+ "top_rtc_32p7k", "csw_f26m_sel", "infra_sysaxi_d2", "pwm_sel"
+};
+
+static const char *const infra_pcie_parents[] __initconst = {
+ "top_rtc_32p7k", "csw_f26m_sel", "top_xtal", "pextp_tl_ck_sel"
+};
+
+static const struct mtk_mux infra_muxes[] = {
+ /* MODULE_CLK_SEL_0 */
+ MUX_GATE_CLR_SET_UPD(CLK_INFRA_UART0_SEL, "infra_uart0_sel",
+ infra_uart_parent, 0x0018, 0x0010, 0x0014, 0, 1,
+ -1, -1, -1),
+ MUX_GATE_CLR_SET_UPD(CLK_INFRA_UART1_SEL, "infra_uart1_sel",
+ infra_uart_parent, 0x0018, 0x0010, 0x0014, 1, 1,
+ -1, -1, -1),
+ MUX_GATE_CLR_SET_UPD(CLK_INFRA_UART2_SEL, "infra_uart2_sel",
+ infra_uart_parent, 0x0018, 0x0010, 0x0014, 2, 1,
+ -1, -1, -1),
+ MUX_GATE_CLR_SET_UPD(CLK_INFRA_SPI0_SEL, "infra_spi0_sel",
+ infra_spi_parents, 0x0018, 0x0010, 0x0014, 4, 1,
+ -1, -1, -1),
+ MUX_GATE_CLR_SET_UPD(CLK_INFRA_SPI1_SEL, "infra_spi1_sel",
+ infra_spi_parents, 0x0018, 0x0010, 0x0014, 5, 1,
+ -1, -1, -1),
+ MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM1_SEL, "infra_pwm1_sel",
+ infra_pwm_bsel_parents, 0x0018, 0x0010, 0x0014, 9,
+ 2, -1, -1, -1),
+ MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM2_SEL, "infra_pwm2_sel",
+ infra_pwm_bsel_parents, 0x0018, 0x0010, 0x0014, 11,
+ 2, -1, -1, -1),
+ MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM_BSEL, "infra_pwm_bsel",
+ infra_pwm_bsel_parents, 0x0018, 0x0010, 0x0014, 13,
+ 2, -1, -1, -1),
+ /* MODULE_CLK_SEL_1 */
+ MUX_GATE_CLR_SET_UPD(CLK_INFRA_PCIE_SEL, "infra_pcie_sel",
+ infra_pcie_parents, 0x0028, 0x0020, 0x0024, 0, 2,
+ -1, -1, -1),
+};
+
+static const struct mtk_gate_regs infra0_cg_regs = {
+ .set_ofs = 0x40,
+ .clr_ofs = 0x44,
+ .sta_ofs = 0x48,
+};
+
+static const struct mtk_gate_regs infra1_cg_regs = {
+ .set_ofs = 0x50,
+ .clr_ofs = 0x54,
+ .sta_ofs = 0x58,
+};
+
+static const struct mtk_gate_regs infra2_cg_regs = {
+ .set_ofs = 0x60,
+ .clr_ofs = 0x64,
+ .sta_ofs = 0x68,
+};
+
+#define GATE_INFRA0(_id, _name, _parent, _shift) \
+ { \
+ .id = _id, .name = _name, .parent_name = _parent, \
+ .regs = &infra0_cg_regs, .shift = _shift, \
+ .ops = &mtk_clk_gate_ops_setclr, \
+ }
+
+#define GATE_INFRA1(_id, _name, _parent, _shift) \
+ { \
+ .id = _id, .name = _name, .parent_name = _parent, \
+ .regs = &infra1_cg_regs, .shift = _shift, \
+ .ops = &mtk_clk_gate_ops_setclr, \
+ }
+
+#define GATE_INFRA2(_id, _name, _parent, _shift) \
+ { \
+ .id = _id, .name = _name, .parent_name = _parent, \
+ .regs = &infra2_cg_regs, .shift = _shift, \
+ .ops = &mtk_clk_gate_ops_setclr, \
+ }
+
+static const struct mtk_gate infra_clks[] __initconst = {
+ /* INFRA0 */
+ GATE_INFRA0(CLK_INFRA_GPT_STA, "infra_gpt_sta", "infra_sysaxi_d2", 0),
+ GATE_INFRA0(CLK_INFRA_PWM_HCK, "infra_pwm_hck", "infra_sysaxi_d2", 1),
+ GATE_INFRA0(CLK_INFRA_PWM_STA, "infra_pwm_sta", "infra_pwm_bsel", 2),
+ GATE_INFRA0(CLK_INFRA_PWM1_CK, "infra_pwm1", "infra_pwm1_sel", 3),
+ GATE_INFRA0(CLK_INFRA_PWM2_CK, "infra_pwm2", "infra_pwm2_sel", 4),
+ GATE_INFRA0(CLK_INFRA_CQ_DMA_CK, "infra_cq_dma", "sysaxi_sel", 6),
+ GATE_INFRA0(CLK_INFRA_EIP97_CK, "infra_eip97", "eip_b_sel", 7),
+ GATE_INFRA0(CLK_INFRA_AUD_BUS_CK, "infra_aud_bus", "sysaxi_sel", 8),
+ GATE_INFRA0(CLK_INFRA_AUD_26M_CK, "infra_aud_26m", "csw_f26m_sel", 9),
+ GATE_INFRA0(CLK_INFRA_AUD_L_CK, "infra_aud_l", "aud_l_sel", 10),
+ GATE_INFRA0(CLK_INFRA_AUD_AUD_CK, "infra_aud_aud", "a1sys_sel", 11),
+ GATE_INFRA0(CLK_INFRA_AUD_EG2_CK, "infra_aud_eg2", "a_tuner_sel", 13),
+ GATE_INFRA0(CLK_INFRA_DRAMC_26M_CK, "infra_dramc_26m", "csw_f26m_sel",
+ 14),
+ GATE_INFRA0(CLK_INFRA_DBG_CK, "infra_dbg", "infra_sysaxi_d2", 15),
+ GATE_INFRA0(CLK_INFRA_AP_DMA_CK, "infra_ap_dma", "infra_sysaxi_d2", 16),
+ GATE_INFRA0(CLK_INFRA_SEJ_CK, "infra_sej", "infra_sysaxi_d2", 24),
+ GATE_INFRA0(CLK_INFRA_SEJ_13M_CK, "infra_sej_13m", "csw_f26m_sel", 25),
+ GATE_INFRA0(CLK_INFRA_TRNG_CK, "infra_trng", "sysaxi_sel", 26),
+ /* INFRA1 */
+ GATE_INFRA1(CLK_INFRA_THERM_CK, "infra_therm", "csw_f26m_sel", 0),
+ GATE_INFRA1(CLK_INFRA_I2C0_CK, "infra_i2c0", "i2c_sel", 1),
+ GATE_INFRA1(CLK_INFRA_UART0_CK, "infra_uart0", "infra_uart0_sel", 2),
+ GATE_INFRA1(CLK_INFRA_UART1_CK, "infra_uart1", "infra_uart1_sel", 3),
+ GATE_INFRA1(CLK_INFRA_UART2_CK, "infra_uart2", "infra_uart2_sel", 4),
+ GATE_INFRA1(CLK_INFRA_NFI1_CK, "infra_nfi1", "nfi1x_sel", 8),
+ GATE_INFRA1(CLK_INFRA_SPINFI1_CK, "infra_spinfi1", "spinfi_sel", 9),
+ GATE_INFRA1(CLK_INFRA_NFI_HCK_CK, "infra_nfi_hck", "infra_sysaxi_d2",
+ 10),
+ GATE_INFRA1(CLK_INFRA_SPI0_CK, "infra_spi0", "infra_spi0_sel", 11),
+ GATE_INFRA1(CLK_INFRA_SPI1_CK, "infra_spi1", "infra_spi1_sel", 12),
+ GATE_INFRA1(CLK_INFRA_SPI0_HCK_CK, "infra_spi0_hck", "infra_sysaxi_d2",
+ 13),
+ GATE_INFRA1(CLK_INFRA_SPI1_HCK_CK, "infra_spi1_hck", "infra_sysaxi_d2",
+ 14),
+ GATE_INFRA1(CLK_INFRA_FRTC_CK, "infra_frtc", "top_rtc_32k", 15),
+ GATE_INFRA1(CLK_INFRA_MSDC_CK, "infra_msdc", "emmc_416m_sel", 16),
+ GATE_INFRA1(CLK_INFRA_MSDC_HCK_CK, "infra_msdc_hck", "emmc_250m_sel",
+ 17),
+ GATE_INFRA1(CLK_INFRA_MSDC_133M_CK, "infra_msdc_133m", "sysaxi_sel",
+ 18),
+ GATE_INFRA1(CLK_INFRA_MSDC_66M_CK, "infra_msdc_66m", "infra_sysaxi_d2",
+ 19),
+ GATE_INFRA1(CLK_INFRA_ADC_26M_CK, "infra_adc_26m", "csw_f26m_sel", 20),
+ GATE_INFRA1(CLK_INFRA_ADC_FRC_CK, "infra_adc_frc", "csw_f26m_sel", 21),
+ GATE_INFRA1(CLK_INFRA_FBIST2FPC_CK, "infra_fbist2fpc", "nfi1x_sel", 23),
+ /* INFRA2 */
+ GATE_INFRA2(CLK_INFRA_IUSB_133_CK, "infra_iusb_133", "sysaxi_sel", 0),
+ GATE_INFRA2(CLK_INFRA_IUSB_66M_CK, "infra_iusb_66m", "infra_sysaxi_d2",
+ 1),
+ GATE_INFRA2(CLK_INFRA_IUSB_SYS_CK, "infra_iusb_sys", "u2u3_sys_sel", 2),
+ GATE_INFRA2(CLK_INFRA_IUSB_CK, "infra_iusb", "u2u3_sel", 3),
+ GATE_INFRA2(CLK_INFRA_IPCIE_CK, "infra_ipcie", "pextp_tl_ck_sel", 12),
+ GATE_INFRA2(CLK_INFRA_IPCIE_PIPE_CK, "infra_ipcie_pipe", "top_xtal",
+ 13),
+ GATE_INFRA2(CLK_INFRA_IPCIER_CK, "infra_ipcier", "csw_f26m_sel", 14),
+ GATE_INFRA2(CLK_INFRA_IPCIEB_CK, "infra_ipcieb", "sysaxi_sel", 15),
+};
+
+static void __init mtk_infracfg_init(struct device_node *node)
+{
+ struct clk_onecell_data *clk_data;
+ int r;
+ void __iomem *base;
+ int nr = ARRAY_SIZE(infra_divs) + ARRAY_SIZE(infra_muxes) +
+ ARRAY_SIZE(infra_clks);
+
+ base = of_iomap(node, 0);
+ if (!base) {
+ pr_err("%s(): ioremap failed\n", __func__);
+ return;
+ }
+
+ clk_data = mtk_alloc_clk_data(nr);
+ mtk_clk_register_factors(infra_divs, ARRAY_SIZE(infra_divs), clk_data);
+ mtk_clk_register_muxes(infra_muxes, ARRAY_SIZE(infra_muxes), node,
+ &mt7986_clk_lock, clk_data);
+ mtk_clk_register_gates(node, infra_clks, ARRAY_SIZE(infra_clks),
+ clk_data);
+
+ r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);
+ if (r)
+ pr_err("%s(): could not register clock provider: %d\n",
+ __func__, r);
+}
+CLK_OF_DECLARE(mtk_infracfg, "mediatek,mt7986-infracfg", mtk_infracfg_init);
diff --git a/drivers/clk/mediatek/clk-mt7986-topckgen.c b/drivers/clk/mediatek/clk-mt7986-topckgen.c
new file mode 100644
index 000000000000..0a376044d290
--- /dev/null
+++ b/drivers/clk/mediatek/clk-mt7986-topckgen.c
@@ -0,0 +1,319 @@
+// SPDX-License-Identifier: GPL-1.0
+/*
+ * Copyright (c) 2021 MediaTek Inc.
+ * Author: Sam Shih <[email protected]>
+ * Author: Wenzhen Yu <[email protected]>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include "clk-mtk.h"
+#include "clk-gate.h"
+#include "clk-mux.h"
+
+#include <dt-bindings/clock/mt7986-clk.h>
+#include <linux/clk.h>
+
+static DEFINE_SPINLOCK(mt7986_clk_lock);
+
+static const struct mtk_fixed_clk top_fixed_clks[] = {
+ FIXED_CLK(CLK_TOP_XTAL, "top_xtal", "clkxtal", 40000000),
+ FIXED_CLK(CLK_TOP_JTAG, "top_jtag", "clkxtal", 50000000),
+};
+
+static const struct mtk_fixed_factor top_divs[] __initconst = {
+ /* XTAL */
+ FACTOR(CLK_TOP_XTAL_D2, "top_xtal_d2", "top_xtal", 1, 2),
+ FACTOR(CLK_TOP_RTC_32K, "top_rtc_32k", "top_xtal", 1, 1250),
+ FACTOR(CLK_TOP_RTC_32P7K, "top_rtc_32p7k", "top_xtal", 1, 1220),
+ /* MPLL */
+ FACTOR(CLK_TOP_MPLL_D2, "top_mpll_d2", "mpll", 1, 2),
+ FACTOR(CLK_TOP_MPLL_D4, "top_mpll_d4", "mpll", 1, 4),
+ FACTOR(CLK_TOP_MPLL_D8, "top_mpll_d8", "mpll", 1, 8),
+ FACTOR(CLK_TOP_MPLL_D8_D2, "top_mpll_d8_d2", "mpll", 1, 16),
+ FACTOR(CLK_TOP_MPLL_D3_D2, "top_mpll_d3_d2", "mpll", 1, 6),
+ /* MMPLL */
+ FACTOR(CLK_TOP_MMPLL_D2, "top_mmpll_d2", "mmpll", 1, 2),
+ FACTOR(CLK_TOP_MMPLL_D4, "top_mmpll_d4", "mmpll", 1, 4),
+ FACTOR(CLK_TOP_MMPLL_D8, "top_mmpll_d8", "mmpll", 1, 8),
+ FACTOR(CLK_TOP_MMPLL_D8_D2, "top_mmpll_d8_d2", "mmpll", 1, 16),
+ FACTOR(CLK_TOP_MMPLL_D3_D8, "top_mmpll_d3_d8", "mmpll", 1, 24),
+ FACTOR(CLK_TOP_MMPLL_U2PHY, "top_mmpll_u2phy", "mmpll", 1, 30),
+ /* APLL2 */
+ FACTOR(CLK_TOP_APLL2_D4, "top_apll2_d4", "apll2", 1, 4),
+ /* NET1PLL */
+ FACTOR(CLK_TOP_NET1PLL_D4, "top_net1pll_d4", "net1pll", 1, 4),
+ FACTOR(CLK_TOP_NET1PLL_D5, "top_net1pll_d5", "net1pll", 1, 5),
+ FACTOR(CLK_TOP_NET1PLL_D5_D2, "top_net1pll_d5_d2", "net1pll", 1, 10),
+ FACTOR(CLK_TOP_NET1PLL_D5_D4, "top_net1pll_d5_d4", "net1pll", 1, 20),
+ FACTOR(CLK_TOP_NET1PLL_D8_D2, "top_net1pll_d8_d2", "net1pll", 1, 16),
+ FACTOR(CLK_TOP_NET1PLL_D8_D4, "top_net1pll_d8_d4", "net1pll", 1, 32),
+ /* NET2PLL */
+ FACTOR(CLK_TOP_NET2PLL_D4, "top_net2pll_d4", "net2pll", 1, 4),
+ FACTOR(CLK_TOP_NET2PLL_D4_D2, "top_net2pll_d4_d2", "net2pll", 1, 8),
+ FACTOR(CLK_TOP_NET2PLL_D3_D2, "top_net2pll_d3_d2", "net2pll", 1, 2),
+ /* WEDMCUPLL */
+ FACTOR(CLK_TOP_WEDMCUPLL_D5_D2, "top_wedmcupll_d5_d2", "wedmcupll", 1,
+ 10),
+};
+
+static const char *const nfi1x_parents[] __initconst = { "top_xtal",
+ "top_mmpll_d8",
+ "top_net1pll_d8_d2",
+ "top_net2pll_d3_d2",
+ "top_mpll_d4",
+ "top_mmpll_d8_d2",
+ "top_wedmcupll_d5_d2",
+ "top_mpll_d8" };
+
+static const char *const spinfi_parents[] __initconst = {
+ "top_xtal_d2", "top_xtal", "top_net1pll_d5_d4",
+ "top_mpll_d4", "top_mmpll_d8_d2", "top_wedmcupll_d5_d2",
+ "top_mmpll_d3_d8", "top_mpll_d8"
+};
+
+static const char *const spi_parents[] __initconst = {
+ "top_xtal", "top_mpll_d2", "top_mmpll_d8",
+ "top_net1pll_d8_d2", "top_net2pll_d3_d2", "top_net1pll_d5_d4",
+ "top_mpll_d4", "top_wedmcupll_d5_d2"
+};
+
+static const char *const uart_parents[] __initconst = { "top_xtal",
+ "top_mpll_d8",
+ "top_mpll_d8_d2" };
+
+static const char *const pwm_parents[] __initconst = {
+ "top_xtal", "top_net1pll_d8_d2", "top_net1pll_d5_d4", "top_mpll_d4"
+};
+
+static const char *const i2c_parents[] __initconst = {
+ "top_xtal", "top_net1pll_d5_d4", "top_mpll_d4", "top_net1pll_d8_d4"
+};
+
+static const char *const pextp_tl_ck_parents[] __initconst = {
+ "top_xtal", "top_net1pll_d5_d4", "top_net2pll_d4_d2", "top_rtc_32k"
+};
+
+static const char *const emmc_250m_parents[] __initconst = {
+ "top_xtal", "top_net1pll_d5_d2"
+};
+
+static const char *const emmc_416m_parents[] __initconst = { "top_xtal",
+ "mpll" };
+
+static const char *const f_26m_adc_parents[] __initconst = { "top_xtal",
+ "top_mpll_d8_d2" };
+
+static const char *const dramc_md32_parents[] __initconst = { "top_xtal",
+ "top_mpll_d2" };
+
+static const char *const sysaxi_parents[] __initconst = { "top_xtal",
+ "top_net1pll_d8_d2",
+ "top_net2pll_d4" };
+
+static const char *const sysapb_parents[] __initconst = { "top_xtal",
+ "top_mpll_d3_d2",
+ "top_net2pll_d4_d2" };
+
+static const char *const arm_db_main_parents[] __initconst = {
+ "top_xtal", "top_net2pll_d3_d2"
+};
+
+static const char *const arm_db_jtsel_parents[] __initconst = { "top_jtag",
+ "top_xtal" };
+
+static const char *const netsys_parents[] __initconst = { "top_xtal",
+ "top_mmpll_d4" };
+
+static const char *const netsys_500m_parents[] __initconst = {
+ "top_xtal", "top_net1pll_d5"
+};
+
+static const char *const netsys_mcu_parents[] __initconst = {
+ "top_xtal", "wedmcupll", "top_mmpll_d2", "top_net1pll_d4",
+ "top_net1pll_d5"
+};
+
+static const char *const netsys_2x_parents[] __initconst = {
+ "top_xtal", "net2pll", "wedmcupll", "top_mmpll_d2"
+};
+
+static const char *const sgm_325m_parents[] __initconst = { "top_xtal",
+ "sgmpll" };
+
+static const char *const sgm_reg_parents[] __initconst = {
+ "top_xtal", "top_net1pll_d8_d4"
+};
+
+static const char *const a1sys_parents[] __initconst = { "top_xtal",
+ "top_apll2_d4" };
+
+static const char *const conn_mcusys_parents[] __initconst = { "top_xtal",
+ "top_mmpll_d2" };
+
+static const char *const eip_b_parents[] __initconst = { "top_xtal",
+ "net2pll" };
+
+static const char *const aud_l_parents[] __initconst = { "top_xtal", "apll2",
+ "top_mpll_d8_d2" };
+
+static const char *const a_tuner_parents[] __initconst = { "top_xtal",
+ "top_apll2_d4",
+ "top_mpll_d8_d2" };
+
+static const char *const u2u3_sys_parents[] __initconst = {
+ "top_xtal", "top_net1pll_d5_d4"
+};
+
+static const char *const da_u2_refsel_parents[] __initconst = {
+ "top_xtal", "top_mmpll_u2phy"
+};
+
+static const struct mtk_mux top_muxes[] = {
+ /* CLK_CFG_0 */
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_NFI1X_SEL, "nfi1x_sel", nfi1x_parents,
+ 0x000, 0x004, 0x008, 0, 3, 7, 0x1C0, 0),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_SPINFI_SEL, "spinfi_sel", spinfi_parents,
+ 0x000, 0x004, 0x008, 8, 3, 15, 0x1C0, 1),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_SPI_SEL, "spi_sel", spi_parents, 0x000,
+ 0x004, 0x008, 16, 3, 23, 0x1C0, 2),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_SPIM_MST_SEL, "spim_mst_sel", spi_parents,
+ 0x000, 0x004, 0x008, 24, 3, 31, 0x1C0, 3),
+ /* CLK_CFG_1 */
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_UART_SEL, "uart_sel", uart_parents, 0x010,
+ 0x014, 0x018, 0, 2, 7, 0x1C0, 4),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_PWM_SEL, "pwm_sel", pwm_parents, 0x010,
+ 0x014, 0x018, 8, 2, 15, 0x1C0, 5),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_I2C_SEL, "i2c_sel", i2c_parents, 0x010,
+ 0x014, 0x018, 16, 2, 23, 0x1C0, 6),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_PEXTP_TL_SEL, "pextp_tl_ck_sel",
+ pextp_tl_ck_parents, 0x010, 0x014, 0x018, 24, 2,
+ 31, 0x1C0, 7),
+ /* CLK_CFG_2 */
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_EMMC_250M_SEL, "emmc_250m_sel",
+ emmc_250m_parents, 0x020, 0x024, 0x028, 0, 1, 7,
+ 0x1C0, 8),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_EMMC_416M_SEL, "emmc_416m_sel",
+ emmc_416m_parents, 0x020, 0x024, 0x028, 8, 1, 15,
+ 0x1C0, 9),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_F_26M_ADC_SEL, "f_26m_adc_sel",
+ f_26m_adc_parents, 0x020, 0x024, 0x028, 16, 1, 23,
+ 0x1C0, 10),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_DRAMC_SEL, "dramc_sel", f_26m_adc_parents,
+ 0x020, 0x024, 0x028, 24, 1, 31, 0x1C0, 11),
+ /* CLK_CFG_3 */
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_DRAMC_MD32_SEL, "dramc_md32_sel",
+ dramc_md32_parents, 0x030, 0x034, 0x038, 0, 1, 7,
+ 0x1C0, 12),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_SYSAXI_SEL, "sysaxi_sel", sysaxi_parents,
+ 0x030, 0x034, 0x038, 8, 2, 15, 0x1C0, 13),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_SYSAPB_SEL, "sysapb_sel", sysapb_parents,
+ 0x030, 0x034, 0x038, 16, 2, 23, 0x1C0, 14),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_ARM_DB_MAIN_SEL, "arm_db_main_sel",
+ arm_db_main_parents, 0x030, 0x034, 0x038, 24, 1,
+ 31, 0x1C0, 15),
+ /* CLK_CFG_4 */
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_ARM_DB_JTSEL, "arm_db_jtsel",
+ arm_db_jtsel_parents, 0x040, 0x044, 0x048, 0, 1, 7,
+ 0x1C0, 16),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_SEL, "netsys_sel", netsys_parents,
+ 0x040, 0x044, 0x048, 8, 1, 15, 0x1C0, 17),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_500M_SEL, "netsys_500m_sel",
+ netsys_500m_parents, 0x040, 0x044, 0x048, 16, 1,
+ 23, 0x1C0, 18),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_MCU_SEL, "netsys_mcu_sel",
+ netsys_mcu_parents, 0x040, 0x044, 0x048, 24, 3, 31,
+ 0x1C0, 19),
+ /* CLK_CFG_5 */
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_2X_SEL, "netsys_2x_sel",
+ netsys_2x_parents, 0x050, 0x054, 0x058, 0, 2, 7,
+ 0x1C0, 20),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_SGM_325M_SEL, "sgm_325m_sel",
+ sgm_325m_parents, 0x050, 0x054, 0x058, 8, 1, 15,
+ 0x1C0, 21),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_SGM_REG_SEL, "sgm_reg_sel",
+ sgm_reg_parents, 0x050, 0x054, 0x058, 16, 1, 23,
+ 0x1C0, 22),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_A1SYS_SEL, "a1sys_sel", a1sys_parents,
+ 0x050, 0x054, 0x058, 24, 1, 31, 0x1C0, 23),
+ /* CLK_CFG_6 */
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_CONN_MCUSYS_SEL, "conn_mcusys_sel",
+ conn_mcusys_parents, 0x060, 0x064, 0x068, 0, 1, 7,
+ 0x1C0, 24),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_EIP_B_SEL, "eip_b_sel", eip_b_parents,
+ 0x060, 0x064, 0x068, 8, 1, 15, 0x1C0, 25),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_PCIE_PHY_SEL, "pcie_phy_sel",
+ f_26m_adc_parents, 0x060, 0x064, 0x068, 16, 1, 23,
+ 0x1C0, 26),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_USB3_PHY_SEL, "usb3_phy_sel",
+ f_26m_adc_parents, 0x060, 0x064, 0x068, 24, 1, 31,
+ 0x1C0, 27),
+ /* CLK_CFG_7 */
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_F26M_SEL, "csw_f26m_sel",
+ f_26m_adc_parents, 0x070, 0x074, 0x078, 0, 1, 7,
+ 0x1C0, 28),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_AUD_L_SEL, "aud_l_sel", aud_l_parents,
+ 0x070, 0x074, 0x078, 8, 2, 15, 0x1C0, 29),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_A_TUNER_SEL, "a_tuner_sel",
+ a_tuner_parents, 0x070, 0x074, 0x078, 16, 2, 23,
+ 0x1C0, 30),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_U2U3_SEL, "u2u3_sel", f_26m_adc_parents,
+ 0x070, 0x074, 0x078, 24, 1, 31, 0x1C4, 0),
+ /* CLK_CFG_8 */
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_U2U3_SYS_SEL, "u2u3_sys_sel",
+ u2u3_sys_parents, 0x080, 0x084, 0x088, 0, 1, 7,
+ 0x1C4, 1),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_U2U3_XHCI_SEL, "u2u3_xhci_sel",
+ u2u3_sys_parents, 0x080, 0x084, 0x088, 8, 1, 15,
+ 0x1C4, 2),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_DA_U2_REFSEL, "da_u2_refsel",
+ da_u2_refsel_parents, 0x080, 0x084, 0x088, 16, 1,
+ 23, 0x1C4, 3),
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_DA_U2_CK_1P_SEL, "da_u2_ck_1p_sel",
+ da_u2_refsel_parents, 0x080, 0x084, 0x088, 24, 1,
+ 31, 0x1C4, 4),
+ /* CLK_CFG_9 */
+ MUX_GATE_CLR_SET_UPD(CLK_TOP_AP2CNN_HOST_SEL, "ap2cnn_host_sel",
+ sgm_reg_parents, 0x090, 0x094, 0x098, 0, 1, 7,
+ 0x1C4, 5),
+};
+
+static void __init mtk_topckgen_init(struct device_node *node)
+{
+ struct clk_onecell_data *clk_data;
+ int r;
+ void __iomem *base;
+ int nr = ARRAY_SIZE(top_fixed_clks) + ARRAY_SIZE(top_divs) +
+ ARRAY_SIZE(top_muxes);
+
+ base = of_iomap(node, 0);
+ if (!base) {
+ pr_err("%s(): ioremap failed\n", __func__);
+ return;
+ }
+
+ clk_data = mtk_alloc_clk_data(nr);
+
+ mtk_clk_register_fixed_clks(top_fixed_clks, ARRAY_SIZE(top_fixed_clks),
+ clk_data);
+ mtk_clk_register_factors(top_divs, ARRAY_SIZE(top_divs), clk_data);
+ mtk_clk_register_muxes(top_muxes, ARRAY_SIZE(top_muxes), node,
+ &mt7986_clk_lock, clk_data);
+
+ clk_prepare_enable(clk_data->clks[CLK_TOP_SYSAXI_SEL]);
+ clk_prepare_enable(clk_data->clks[CLK_TOP_SYSAPB_SEL]);
+ clk_prepare_enable(clk_data->clks[CLK_TOP_DRAMC_SEL]);
+ clk_prepare_enable(clk_data->clks[CLK_TOP_DRAMC_MD32_SEL]);
+ clk_prepare_enable(clk_data->clks[CLK_TOP_F26M_SEL]);
+ clk_prepare_enable(clk_data->clks[CLK_TOP_SGM_REG_SEL]);
+
+ r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);
+
+ if (r)
+ pr_err("%s(): could not register clock provider: %d\n",
+ __func__, r);
+}
+CLK_OF_DECLARE(mtk_topckgen, "mediatek,mt7986-topckgen", mtk_topckgen_init);
--
2.29.2
Certain SoC are missing the middle part gpios in consecutive pins,
it's better to check if mtk_pin_desc is a valid pin for the extensibility
Signed-off-by: Sam Shih <[email protected]>
Acked-by: Sean Wang <[email protected]>
---
v3: added an Acked-by tag.
v2: applied the comment suggested by reviewers:
- for the pins not ballout, we can fill .name in struct mtk_pin_desc
as NULL and return -ENOTSUPP in gpio/pinconf ops.
---
drivers/pinctrl/mediatek/pinctrl-moore.c | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/drivers/pinctrl/mediatek/pinctrl-moore.c b/drivers/pinctrl/mediatek/pinctrl-moore.c
index 3a4a23c40a71..ad3b67163973 100644
--- a/drivers/pinctrl/mediatek/pinctrl-moore.c
+++ b/drivers/pinctrl/mediatek/pinctrl-moore.c
@@ -60,6 +60,8 @@ static int mtk_pinmux_set_mux(struct pinctrl_dev *pctldev,
int pin = grp->pins[i];
desc = (const struct mtk_pin_desc *)&hw->soc->pins[pin];
+ if (!desc->name)
+ return -ENOTSUPP;
mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_MODE,
pin_modes[i]);
@@ -76,6 +78,8 @@ static int mtk_pinmux_gpio_request_enable(struct pinctrl_dev *pctldev,
const struct mtk_pin_desc *desc;
desc = (const struct mtk_pin_desc *)&hw->soc->pins[pin];
+ if (!desc->name)
+ return -ENOTSUPP;
return mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_MODE,
hw->soc->gpio_m);
@@ -89,6 +93,8 @@ static int mtk_pinmux_gpio_set_direction(struct pinctrl_dev *pctldev,
const struct mtk_pin_desc *desc;
desc = (const struct mtk_pin_desc *)&hw->soc->pins[pin];
+ if (!desc->name)
+ return -ENOTSUPP;
/* hardware would take 0 as input direction */
return mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_DIR, !input);
@@ -103,6 +109,8 @@ static int mtk_pinconf_get(struct pinctrl_dev *pctldev,
const struct mtk_pin_desc *desc;
desc = (const struct mtk_pin_desc *)&hw->soc->pins[pin];
+ if (!desc->name)
+ return -ENOTSUPP;
switch (param) {
case PIN_CONFIG_BIAS_DISABLE:
@@ -218,6 +226,8 @@ static int mtk_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
int cfg, err = 0;
desc = (const struct mtk_pin_desc *)&hw->soc->pins[pin];
+ if (!desc->name)
+ return -ENOTSUPP;
for (cfg = 0; cfg < num_configs; cfg++) {
param = pinconf_to_config_param(configs[cfg]);
@@ -435,6 +445,8 @@ static int mtk_gpio_get(struct gpio_chip *chip, unsigned int gpio)
int value, err;
desc = (const struct mtk_pin_desc *)&hw->soc->pins[gpio];
+ if (!desc->name)
+ return -ENOTSUPP;
err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_DI, &value);
if (err)
@@ -449,6 +461,10 @@ static void mtk_gpio_set(struct gpio_chip *chip, unsigned int gpio, int value)
const struct mtk_pin_desc *desc;
desc = (const struct mtk_pin_desc *)&hw->soc->pins[gpio];
+ if (!desc->name) {
+ dev_err(hw->dev, "Failed to set gpio %d\n", gpio);
+ return;
+ }
mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_DO, !!value);
}
@@ -490,6 +506,8 @@ static int mtk_gpio_set_config(struct gpio_chip *chip, unsigned int offset,
u32 debounce;
desc = (const struct mtk_pin_desc *)&hw->soc->pins[offset];
+ if (!desc->name)
+ return -ENOTSUPP;
if (!hw->eint ||
pinconf_to_config_param(config) != PIN_CONFIG_INPUT_DEBOUNCE ||
--
2.29.2
This commit includes pinctrl driver for Mediatek MT7986
The difference of pinctrl between mt7986a and mt7986b
is that pin-41 to pin-65 do not exist on mt7986b
Signed-off-by: Sam Shih <[email protected]>
---
v4: fixed warning in mt7986 pinctrl driver
v3: applied the comment suggested by reviewers:
- merge the consecutive entries into one to reduce the table size
- set .name to NULL to indicate the pin is not ball out
v2: applied the comment suggested by reviewers:
- for the pins not ballout, we can fill .name in struct mtk_pin_desc
as NULL and return -ENOTSUPP in gpio/pinconf ops.
---
drivers/pinctrl/mediatek/Kconfig | 7 +
drivers/pinctrl/mediatek/Makefile | 1 +
drivers/pinctrl/mediatek/pinctrl-mt7986.c | 928 ++++++++++++++++++++++
3 files changed, 936 insertions(+)
create mode 100644 drivers/pinctrl/mediatek/pinctrl-mt7986.c
diff --git a/drivers/pinctrl/mediatek/Kconfig b/drivers/pinctrl/mediatek/Kconfig
index 7040a7a7bd5d..66db4ac5d169 100644
--- a/drivers/pinctrl/mediatek/Kconfig
+++ b/drivers/pinctrl/mediatek/Kconfig
@@ -119,6 +119,13 @@ config PINCTRL_MT7622
default ARM64 && ARCH_MEDIATEK
select PINCTRL_MTK_MOORE
+config PINCTRL_MT7986
+ bool "Mediatek MT7986 pin control"
+ depends on OF
+ depends on ARM64 || COMPILE_TEST
+ default ARM64 && ARCH_MEDIATEK
+ select PINCTRL_MTK_MOORE
+
config PINCTRL_MT8167
bool "Mediatek MT8167 pin control"
depends on OF
diff --git a/drivers/pinctrl/mediatek/Makefile b/drivers/pinctrl/mediatek/Makefile
--- a/drivers/pinctrl/mediatek/Makefile
+++ b/drivers/pinctrl/mediatek/Makefile
@@ -17,6 +17,7 @@ obj-$(CONFIG_PINCTRL_MT6797) += pinctrl-mt6797.o
obj-$(CONFIG_PINCTRL_MT7622) += pinctrl-mt7622.o
obj-$(CONFIG_PINCTRL_MT7623) += pinctrl-mt7623.o
obj-$(CONFIG_PINCTRL_MT7629) += pinctrl-mt7629.o
+obj-$(CONFIG_PINCTRL_MT7986) += pinctrl-mt7986.o
obj-$(CONFIG_PINCTRL_MT8167) += pinctrl-mt8167.o
obj-$(CONFIG_PINCTRL_MT8173) += pinctrl-mt8173.o
obj-$(CONFIG_PINCTRL_MT8183) += pinctrl-mt8183.o
diff --git a/drivers/pinctrl/mediatek/pinctrl-mt7986.c b/drivers/pinctrl/mediatek/pinctrl-mt7986.c
new file mode 100644
--- /dev/null
+++ b/drivers/pinctrl/mediatek/pinctrl-mt7986.c
@@ -0,0 +1,927 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * The MT7986 driver based on Linux generic pinctrl binding.
+ *
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam Shih <[email protected]>
+ */
+
+#include "pinctrl-moore.h"
+
+#define MT7986_PIN(_number, _name) MTK_PIN(_number, _name, 0, _number, DRV_GRP4)
+#define MT7986_NOT_BALLOUT_PIN(_number) { .number = _number, .name = NULL }
+
+#define PIN_FIELD_BASE(_s_pin, _e_pin, _i_base, _s_addr, _x_addrs, _s_bit, \
+ _x_bits) \
+ PIN_FIELD_CALC(_s_pin, _e_pin, _i_base, _s_addr, _x_addrs, _s_bit, \
+ _x_bits, 32, 0)
+
+/**
+ * enum - Locking variants of the iocfg bases
+ *
+ * MT7986 have multiple bases to program pin configuration listed as the below:
+ * iocfg_rt:0x11c30000, iocfg_rb:0x11c40000, iocfg_lt:0x11e20000,
+ * iocfg_lb:0x11e30000, iocfg_tr:0x11f00000, iocfg_tl:0x11f10000,
+ * _i_based could be used to indicate what base the pin should be mapped into.
+ *
+ * Each iocfg register base control different group of pads on the SoC
+ *
+ *
+ * chip carrier
+ *
+ * A B C D E F G H
+ * +------------------------+
+ * 8 | o o o o o o o o |
+ * 7 | o o o o o o o o |
+ * 6 | o o o o o o o o |
+ * 5 | o o o o o o o o |
+ * 4 | o o o o o o o o |
+ * 3 | o o o o o o o o |
+ * 2 | o o o o o o o o |
+ * 1 | o o o o o o o o |
+ * +------------------------+
+ *
+ * inside Chip carrier
+ *
+ * A B C D E F G H
+ * +------------------------+
+ * 8 | |
+ * 7 | TL TR |
+ * 6 | +---------+ |
+ * 5 | LT | | RT |
+ * 4 | | | |
+ * 3 | LB | | RB |
+ * 2 | +---------+ |
+ * 1 | |
+ * +------------------------+
+ *
+ */
+
+enum {
+ GPIO_BASE,
+ IOCFG_RT_BASE,
+ IOCFG_RB_BASE,
+ IOCFG_LT_BASE,
+ IOCFG_LB_BASE,
+ IOCFG_TR_BASE,
+ IOCFG_TL_BASE,
+};
+
+static const char *const mt7986_pinctrl_register_base_names[] = {
+ "gpio_base", "iocfg_rt_base", "iocfg_rb_base", "iocfg_lt_base",
+ "iocfg_lb_base", "iocfg_tr_base", "iocfg_tl_base",
+};
+
+static const struct mtk_pin_field_calc mt7986_pin_mode_range[] = {
+ PIN_FIELD(0, 100, 0x300, 0x10, 0, 4),
+};
+
+static const struct mtk_pin_field_calc mt7986_pin_dir_range[] = {
+ PIN_FIELD(0, 100, 0x0, 0x10, 0, 1),
+};
+
+static const struct mtk_pin_field_calc mt7986_pin_di_range[] = {
+ PIN_FIELD(0, 100, 0x200, 0x10, 0, 1),
+};
+
+static const struct mtk_pin_field_calc mt7986_pin_do_range[] = {
+ PIN_FIELD(0, 100, 0x100, 0x10, 0, 1),
+};
+
+static const struct mtk_pin_field_calc mt7986_pin_ies_range[] = {
+ PIN_FIELD_BASE(0, 0, IOCFG_RB_BASE, 0x40, 0x10, 17, 1),
+ PIN_FIELD_BASE(1, 2, IOCFG_LT_BASE, 0x20, 0x10, 10, 1),
+ PIN_FIELD_BASE(3, 4, IOCFG_LB_BASE, 0x20, 0x10, 0, 1),
+ PIN_FIELD_BASE(5, 6, IOCFG_RB_BASE, 0x40, 0x10, 0, 1),
+ PIN_FIELD_BASE(7, 10, IOCFG_LT_BASE, 0x20, 0x10, 0, 1),
+ PIN_FIELD_BASE(11, 14, IOCFG_RB_BASE, 0x40, 0x10, 8, 1),
+ PIN_FIELD_BASE(15, 20, IOCFG_RB_BASE, 0x40, 0x10, 2, 1),
+ PIN_FIELD_BASE(21, 23, IOCFG_RT_BASE, 0x30, 0x10, 12, 1),
+ PIN_FIELD_BASE(24, 24, IOCFG_RT_BASE, 0x30, 0x10, 18, 1),
+ PIN_FIELD_BASE(25, 25, IOCFG_RT_BASE, 0x30, 0x10, 17, 1),
+ PIN_FIELD_BASE(26, 27, IOCFG_RT_BASE, 0x30, 0x10, 15, 1),
+ PIN_FIELD_BASE(28, 29, IOCFG_RT_BASE, 0x30, 0x10, 19, 1),
+ PIN_FIELD_BASE(30, 30, IOCFG_RT_BASE, 0x30, 0x10, 23, 1),
+ PIN_FIELD_BASE(31, 31, IOCFG_RT_BASE, 0x30, 0x10, 22, 1),
+ PIN_FIELD_BASE(32, 32, IOCFG_RT_BASE, 0x30, 0x10, 21, 1),
+ PIN_FIELD_BASE(33, 33, IOCFG_LT_BASE, 0x20, 0x10, 4, 1),
+ PIN_FIELD_BASE(34, 34, IOCFG_LT_BASE, 0x20, 0x10, 8, 1),
+ PIN_FIELD_BASE(35, 35, IOCFG_LT_BASE, 0x20, 0x10, 7, 1),
+ PIN_FIELD_BASE(36, 37, IOCFG_LT_BASE, 0x20, 0x10, 5, 1),
+ PIN_FIELD_BASE(38, 38, IOCFG_LT_BASE, 0x20, 0x10, 9, 1),
+ PIN_FIELD_BASE(39, 40, IOCFG_RB_BASE, 0x40, 0x10, 18, 1),
+ PIN_FIELD_BASE(41, 41, IOCFG_RB_BASE, 0x40, 0x10, 12, 1),
+ PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0x40, 0x10, 22, 1),
+ PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0x40, 0x10, 20, 1),
+ PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0x40, 0x10, 26, 1),
+ PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0x40, 0x10, 24, 1),
+ PIN_FIELD_BASE(50, 57, IOCFG_RT_BASE, 0x30, 0x10, 2, 1),
+ PIN_FIELD_BASE(58, 58, IOCFG_RT_BASE, 0x30, 0x10, 1, 1),
+ PIN_FIELD_BASE(59, 59, IOCFG_RT_BASE, 0x30, 0x10, 0, 1),
+ PIN_FIELD_BASE(60, 61, IOCFG_RT_BASE, 0x30, 0x10, 10, 1),
+ PIN_FIELD_BASE(62, 62, IOCFG_RB_BASE, 0x40, 0x10, 15, 1),
+ PIN_FIELD_BASE(63, 63, IOCFG_RB_BASE, 0x40, 0x10, 14, 1),
+ PIN_FIELD_BASE(64, 64, IOCFG_RB_BASE, 0x40, 0x10, 13, 1),
+ PIN_FIELD_BASE(65, 65, IOCFG_RB_BASE, 0x40, 0x10, 16, 1),
+ PIN_FIELD_BASE(66, 68, IOCFG_LB_BASE, 0x20, 0x10, 2, 1),
+ PIN_FIELD_BASE(69, 69, IOCFG_TR_BASE, 0x30, 0x10, 1, 1),
+ PIN_FIELD_BASE(70, 70, IOCFG_TR_BASE, 0x30, 0x10, 0, 1),
+ PIN_FIELD_BASE(71, 71, IOCFG_TR_BASE, 0x30, 0x10, 16, 1),
+ PIN_FIELD_BASE(72, 73, IOCFG_TR_BASE, 0x30, 0x10, 14, 1),
+ PIN_FIELD_BASE(74, 74, IOCFG_TR_BASE, 0x30, 0x10, 4, 1),
+ PIN_FIELD_BASE(75, 77, IOCFG_TR_BASE, 0x30, 0x10, 6, 1),
+ PIN_FIELD_BASE(78, 79, IOCFG_TR_BASE, 0x30, 0x10, 2, 1),
+ PIN_FIELD_BASE(80, 84, IOCFG_TR_BASE, 0x30, 0x10, 9, 1),
+ PIN_FIELD_BASE(85, 85, IOCFG_TR_BASE, 0x30, 0x10, 5, 1),
+ PIN_FIELD_BASE(86, 86, IOCFG_TL_BASE, 0x30, 0x10, 1, 1),
+ PIN_FIELD_BASE(87, 87, IOCFG_TL_BASE, 0x30, 0x10, 0, 1),
+ PIN_FIELD_BASE(88, 88, IOCFG_TL_BASE, 0x30, 0x10, 14, 1),
+ PIN_FIELD_BASE(89, 90, IOCFG_TL_BASE, 0x30, 0x10, 12, 1),
+ PIN_FIELD_BASE(91, 94, IOCFG_TL_BASE, 0x30, 0x10, 4, 1),
+ PIN_FIELD_BASE(95, 96, IOCFG_TL_BASE, 0x30, 0x10, 2, 1),
+ PIN_FIELD_BASE(97, 100, IOCFG_TL_BASE, 0x30, 0x10, 8, 1),
+};
+
+static const struct mtk_pin_field_calc mt7986_pin_smt_range[] = {
+ PIN_FIELD_BASE(0, 0, IOCFG_RB_BASE, 0xf0, 0x10, 17, 1),
+ PIN_FIELD_BASE(1, 2, IOCFG_LT_BASE, 0x90, 0x10, 10, 1),
+ PIN_FIELD_BASE(3, 4, IOCFG_LB_BASE, 0x90, 0x10, 0, 1),
+ PIN_FIELD_BASE(5, 6, IOCFG_RB_BASE, 0xf0, 0x10, 0, 1),
+ PIN_FIELD_BASE(7, 10, IOCFG_LT_BASE, 0x90, 0x10, 0, 1),
+ PIN_FIELD_BASE(11, 14, IOCFG_RB_BASE, 0xf0, 0x10, 8, 1),
+ PIN_FIELD_BASE(15, 20, IOCFG_RB_BASE, 0xf0, 0x10, 2, 1),
+ PIN_FIELD_BASE(21, 23, IOCFG_RT_BASE, 0xc0, 0x10, 12, 1),
+ PIN_FIELD_BASE(24, 24, IOCFG_RT_BASE, 0xc0, 0x10, 18, 1),
+ PIN_FIELD_BASE(25, 25, IOCFG_RT_BASE, 0xc0, 0x10, 17, 1),
+ PIN_FIELD_BASE(26, 27, IOCFG_RT_BASE, 0xc0, 0x10, 15, 1),
+ PIN_FIELD_BASE(28, 29, IOCFG_RT_BASE, 0xc0, 0x10, 19, 1),
+ PIN_FIELD_BASE(30, 30, IOCFG_RT_BASE, 0xc0, 0x10, 23, 1),
+ PIN_FIELD_BASE(31, 31, IOCFG_RT_BASE, 0xc0, 0x10, 22, 1),
+ PIN_FIELD_BASE(32, 32, IOCFG_RT_BASE, 0xc0, 0x10, 21, 1),
+ PIN_FIELD_BASE(33, 33, IOCFG_LT_BASE, 0x90, 0x10, 4, 1),
+ PIN_FIELD_BASE(34, 34, IOCFG_LT_BASE, 0x90, 0x10, 8, 1),
+ PIN_FIELD_BASE(35, 35, IOCFG_LT_BASE, 0x90, 0x10, 7, 1),
+ PIN_FIELD_BASE(36, 37, IOCFG_LT_BASE, 0x90, 0x10, 5, 1),
+ PIN_FIELD_BASE(38, 38, IOCFG_LT_BASE, 0x90, 0x10, 9, 1),
+ PIN_FIELD_BASE(39, 40, IOCFG_RB_BASE, 0xf0, 0x10, 18, 1),
+ PIN_FIELD_BASE(41, 41, IOCFG_RB_BASE, 0xf0, 0x10, 12, 1),
+ PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0xf0, 0x10, 22, 1),
+ PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0xf0, 0x10, 20, 1),
+ PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0xf0, 0x10, 26, 1),
+ PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0xf0, 0x10, 24, 1),
+ PIN_FIELD_BASE(50, 57, IOCFG_RT_BASE, 0xc0, 0x10, 2, 1),
+ PIN_FIELD_BASE(58, 58, IOCFG_RT_BASE, 0xc0, 0x10, 1, 1),
+ PIN_FIELD_BASE(59, 59, IOCFG_RT_BASE, 0xc0, 0x10, 0, 1),
+ PIN_FIELD_BASE(60, 61, IOCFG_RT_BASE, 0xc0, 0x10, 10, 1),
+ PIN_FIELD_BASE(62, 62, IOCFG_RB_BASE, 0xf0, 0x10, 15, 1),
+ PIN_FIELD_BASE(63, 63, IOCFG_RB_BASE, 0xf0, 0x10, 14, 1),
+ PIN_FIELD_BASE(64, 64, IOCFG_RB_BASE, 0xf0, 0x10, 13, 1),
+ PIN_FIELD_BASE(65, 65, IOCFG_RB_BASE, 0xf0, 0x10, 16, 1),
+ PIN_FIELD_BASE(66, 68, IOCFG_LB_BASE, 0x90, 0x10, 2, 1),
+ PIN_FIELD_BASE(69, 69, IOCFG_TR_BASE, 0x80, 0x10, 1, 1),
+ PIN_FIELD_BASE(70, 70, IOCFG_TR_BASE, 0x80, 0x10, 0, 1),
+ PIN_FIELD_BASE(71, 71, IOCFG_TR_BASE, 0x80, 0x10, 16, 1),
+ PIN_FIELD_BASE(72, 73, IOCFG_TR_BASE, 0x80, 0x10, 14, 1),
+ PIN_FIELD_BASE(74, 74, IOCFG_TR_BASE, 0x80, 0x10, 4, 1),
+ PIN_FIELD_BASE(75, 77, IOCFG_TR_BASE, 0x80, 0x10, 6, 1),
+ PIN_FIELD_BASE(78, 79, IOCFG_TR_BASE, 0x80, 0x10, 2, 1),
+ PIN_FIELD_BASE(80, 84, IOCFG_TR_BASE, 0x80, 0x10, 9, 1),
+ PIN_FIELD_BASE(85, 85, IOCFG_TR_BASE, 0x80, 0x10, 5, 1),
+ PIN_FIELD_BASE(86, 86, IOCFG_TL_BASE, 0x70, 0x10, 1, 1),
+ PIN_FIELD_BASE(87, 87, IOCFG_TL_BASE, 0x70, 0x10, 0, 1),
+ PIN_FIELD_BASE(88, 88, IOCFG_TL_BASE, 0x70, 0x10, 14, 1),
+ PIN_FIELD_BASE(89, 90, IOCFG_TL_BASE, 0x70, 0x10, 12, 1),
+ PIN_FIELD_BASE(91, 94, IOCFG_TL_BASE, 0x70, 0x10, 4, 1),
+ PIN_FIELD_BASE(95, 96, IOCFG_TL_BASE, 0x70, 0x10, 2, 1),
+ PIN_FIELD_BASE(97, 100, IOCFG_TL_BASE, 0x70, 0x10, 8, 1),
+};
+
+static const struct mtk_pin_field_calc mt7986_pin_pu_range[] = {
+ PIN_FIELD_BASE(69, 69, IOCFG_TR_BASE, 0x50, 0x10, 1, 1),
+ PIN_FIELD_BASE(70, 70, IOCFG_TR_BASE, 0x50, 0x10, 0, 1),
+ PIN_FIELD_BASE(71, 71, IOCFG_TR_BASE, 0x50, 0x10, 16, 1),
+ PIN_FIELD_BASE(72, 73, IOCFG_TR_BASE, 0x50, 0x10, 14, 1),
+ PIN_FIELD_BASE(74, 74, IOCFG_TR_BASE, 0x50, 0x10, 4, 1),
+ PIN_FIELD_BASE(75, 77, IOCFG_TR_BASE, 0x50, 0x10, 6, 1),
+ PIN_FIELD_BASE(78, 79, IOCFG_TR_BASE, 0x50, 0x10, 2, 1),
+ PIN_FIELD_BASE(80, 84, IOCFG_TR_BASE, 0x50, 0x10, 9, 1),
+ PIN_FIELD_BASE(85, 85, IOCFG_TR_BASE, 0x50, 0x10, 5, 1),
+ PIN_FIELD_BASE(86, 86, IOCFG_TL_BASE, 0x50, 0x10, 1, 1),
+ PIN_FIELD_BASE(87, 87, IOCFG_TL_BASE, 0x50, 0x10, 0, 1),
+ PIN_FIELD_BASE(88, 88, IOCFG_TL_BASE, 0x50, 0x10, 14, 1),
+ PIN_FIELD_BASE(89, 90, IOCFG_TL_BASE, 0x50, 0x10, 12, 1),
+ PIN_FIELD_BASE(91, 94, IOCFG_TL_BASE, 0x50, 0x10, 4, 1),
+ PIN_FIELD_BASE(95, 96, IOCFG_TL_BASE, 0x50, 0x10, 2, 1),
+ PIN_FIELD_BASE(97, 100, IOCFG_TL_BASE, 0x50, 0x10, 8, 1),
+};
+
+static const struct mtk_pin_field_calc mt7986_pin_pd_range[] = {
+ PIN_FIELD_BASE(69, 69, IOCFG_TR_BASE, 0x40, 0x10, 1, 1),
+ PIN_FIELD_BASE(70, 70, IOCFG_TR_BASE, 0x40, 0x10, 0, 1),
+ PIN_FIELD_BASE(71, 71, IOCFG_TR_BASE, 0x40, 0x10, 16, 1),
+ PIN_FIELD_BASE(72, 73, IOCFG_TR_BASE, 0x40, 0x10, 14, 1),
+ PIN_FIELD_BASE(74, 74, IOCFG_TR_BASE, 0x40, 0x10, 4, 1),
+ PIN_FIELD_BASE(75, 77, IOCFG_TR_BASE, 0x40, 0x10, 6, 1),
+ PIN_FIELD_BASE(78, 79, IOCFG_TR_BASE, 0x40, 0x10, 2, 1),
+ PIN_FIELD_BASE(80, 84, IOCFG_TR_BASE, 0x40, 0x10, 9, 1),
+ PIN_FIELD_BASE(85, 85, IOCFG_TR_BASE, 0x40, 0x10, 5, 1),
+ PIN_FIELD_BASE(86, 86, IOCFG_TL_BASE, 0x40, 0x10, 1, 1),
+ PIN_FIELD_BASE(87, 87, IOCFG_TL_BASE, 0x40, 0x10, 0, 1),
+ PIN_FIELD_BASE(88, 88, IOCFG_TL_BASE, 0x40, 0x10, 14, 1),
+ PIN_FIELD_BASE(89, 90, IOCFG_TL_BASE, 0x40, 0x10, 12, 1),
+ PIN_FIELD_BASE(91, 94, IOCFG_TL_BASE, 0x40, 0x10, 4, 1),
+ PIN_FIELD_BASE(95, 96, IOCFG_TL_BASE, 0x40, 0x10, 2, 1),
+ PIN_FIELD_BASE(97, 100, IOCFG_TL_BASE, 0x40, 0x10, 8, 1),
+};
+
+static const struct mtk_pin_field_calc mt7986_pin_drv_range[] = {
+ PIN_FIELD_BASE(0, 0, IOCFG_RB_BASE, 0x10, 0x10, 21, 3),
+ PIN_FIELD_BASE(1, 2, IOCFG_LT_BASE, 0x10, 0x10, 0, 3),
+ PIN_FIELD_BASE(3, 4, IOCFG_LB_BASE, 0x00, 0x10, 0, 1),
+ PIN_FIELD_BASE(5, 5, IOCFG_RB_BASE, 0x00, 0x10, 0, 3),
+ PIN_FIELD_BASE(6, 6, IOCFG_RB_BASE, 0x00, 0x10, 21, 3),
+ PIN_FIELD_BASE(7, 10, IOCFG_LT_BASE, 0x00, 0x10, 0, 3),
+ PIN_FIELD_BASE(11, 12, IOCFG_RB_BASE, 0x00, 0x10, 24, 3),
+ PIN_FIELD_BASE(13, 14, IOCFG_RB_BASE, 0x10, 0x10, 0, 3),
+ PIN_FIELD_BASE(15, 20, IOCFG_RB_BASE, 0x00, 0x10, 3, 3),
+ PIN_FIELD_BASE(21, 23, IOCFG_RT_BASE, 0x10, 0x10, 6, 3),
+ PIN_FIELD_BASE(24, 24, IOCFG_RT_BASE, 0x10, 0x10, 24, 3),
+ PIN_FIELD_BASE(25, 25, IOCFG_RT_BASE, 0x10, 0x10, 21, 3),
+ PIN_FIELD_BASE(26, 27, IOCFG_RT_BASE, 0x10, 0x10, 15, 3),
+ PIN_FIELD_BASE(28, 28, IOCFG_RT_BASE, 0x10, 0x10, 27, 3),
+ PIN_FIELD_BASE(29, 29, IOCFG_RT_BASE, 0x20, 0x10, 0, 3),
+ PIN_FIELD_BASE(30, 30, IOCFG_RT_BASE, 0x20, 0x10, 9, 3),
+ PIN_FIELD_BASE(31, 31, IOCFG_RT_BASE, 0x20, 0x10, 6, 3),
+ PIN_FIELD_BASE(32, 32, IOCFG_RT_BASE, 0x20, 0x10, 3, 3),
+ PIN_FIELD_BASE(33, 33, IOCFG_LT_BASE, 0x00, 0x10, 12, 3),
+ PIN_FIELD_BASE(34, 34, IOCFG_LT_BASE, 0x00, 0x10, 24, 3),
+ PIN_FIELD_BASE(35, 35, IOCFG_LT_BASE, 0x00, 0x10, 21, 3),
+ PIN_FIELD_BASE(36, 37, IOCFG_LT_BASE, 0x00, 0x10, 15, 3),
+ PIN_FIELD_BASE(38, 38, IOCFG_LT_BASE, 0x00, 0x10, 27, 3),
+ PIN_FIELD_BASE(39, 39, IOCFG_RB_BASE, 0x10, 0x10, 27, 3),
+ PIN_FIELD_BASE(40, 40, IOCFG_RB_BASE, 0x20, 0x10, 0, 3),
+ PIN_FIELD_BASE(41, 41, IOCFG_RB_BASE, 0x10, 0x10, 6, 3),
+ PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0x20, 0x10, 9, 3),
+ PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0x20, 0x10, 3, 3),
+ PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0x20, 0x10, 21, 3),
+ PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0x20, 0x10, 15, 3),
+ PIN_FIELD_BASE(50, 57, IOCFG_RT_BASE, 0x00, 0x10, 6, 3),
+ PIN_FIELD_BASE(58, 58, IOCFG_RT_BASE, 0x00, 0x10, 3, 3),
+ PIN_FIELD_BASE(59, 59, IOCFG_RT_BASE, 0x00, 0x10, 0, 3),
+ PIN_FIELD_BASE(60, 61, IOCFG_RT_BASE, 0x10, 0x10, 0, 3),
+ PIN_FIELD_BASE(62, 62, IOCFG_RB_BASE, 0x10, 0x10, 15, 3),
+ PIN_FIELD_BASE(63, 63, IOCFG_RB_BASE, 0x10, 0x10, 12, 3),
+ PIN_FIELD_BASE(64, 64, IOCFG_RB_BASE, 0x10, 0x10, 9, 3),
+ PIN_FIELD_BASE(65, 65, IOCFG_RB_BASE, 0x10, 0x10, 18, 3),
+ PIN_FIELD_BASE(66, 68, IOCFG_LB_BASE, 0x00, 0x10, 2, 3),
+ PIN_FIELD_BASE(69, 69, IOCFG_TR_BASE, 0x00, 0x10, 3, 3),
+ PIN_FIELD_BASE(70, 70, IOCFG_TR_BASE, 0x00, 0x10, 0, 3),
+ PIN_FIELD_BASE(71, 71, IOCFG_TR_BASE, 0x10, 0x10, 18, 3),
+ PIN_FIELD_BASE(72, 73, IOCFG_TR_BASE, 0x10, 0x10, 12, 3),
+ PIN_FIELD_BASE(74, 77, IOCFG_TR_BASE, 0x00, 0x10, 15, 3),
+ PIN_FIELD_BASE(78, 79, IOCFG_TR_BASE, 0x00, 0x10, 6, 3),
+ PIN_FIELD_BASE(80, 80, IOCFG_TR_BASE, 0x00, 0x10, 27, 3),
+ PIN_FIELD_BASE(81, 84, IOCFG_TR_BASE, 0x10, 0x10, 0, 3),
+ PIN_FIELD_BASE(85, 85, IOCFG_TR_BASE, 0x00, 0x10, 12, 3),
+ PIN_FIELD_BASE(86, 86, IOCFG_TL_BASE, 0x00, 0x10, 3, 3),
+ PIN_FIELD_BASE(87, 87, IOCFG_TL_BASE, 0x00, 0x10, 0, 3),
+ PIN_FIELD_BASE(88, 88, IOCFG_TL_BASE, 0x10, 0x10, 12, 3),
+ PIN_FIELD_BASE(89, 90, IOCFG_TL_BASE, 0x10, 0x10, 6, 3),
+ PIN_FIELD_BASE(91, 94, IOCFG_TL_BASE, 0x00, 0x10, 12, 3),
+ PIN_FIELD_BASE(95, 96, IOCFG_TL_BASE, 0x00, 0x10, 6, 3),
+ PIN_FIELD_BASE(97, 98, IOCFG_TL_BASE, 0x00, 0x10, 24, 3),
+ PIN_FIELD_BASE(99, 100, IOCFG_TL_BASE, 0x10, 0x10, 2, 3),
+};
+
+static const struct mtk_pin_field_calc mt7986_pin_pupd_range[] = {
+ PIN_FIELD_BASE(0, 0, IOCFG_RB_BASE, 0x60, 0x10, 17, 1),
+ PIN_FIELD_BASE(1, 2, IOCFG_LT_BASE, 0x30, 0x10, 10, 1),
+ PIN_FIELD_BASE(3, 4, IOCFG_LB_BASE, 0x40, 0x10, 0, 1),
+ PIN_FIELD_BASE(5, 6, IOCFG_RB_BASE, 0x60, 0x10, 0, 1),
+ PIN_FIELD_BASE(7, 10, IOCFG_LT_BASE, 0x30, 0x10, 0, 1),
+ PIN_FIELD_BASE(11, 14, IOCFG_RB_BASE, 0x60, 0x10, 8, 1),
+ PIN_FIELD_BASE(15, 20, IOCFG_RB_BASE, 0x60, 0x10, 2, 1),
+ PIN_FIELD_BASE(21, 23, IOCFG_RT_BASE, 0x40, 0x10, 12, 1),
+ PIN_FIELD_BASE(24, 24, IOCFG_RT_BASE, 0x40, 0x10, 18, 1),
+ PIN_FIELD_BASE(25, 25, IOCFG_RT_BASE, 0x40, 0x10, 17, 1),
+ PIN_FIELD_BASE(26, 27, IOCFG_RT_BASE, 0x40, 0x10, 15, 1),
+ PIN_FIELD_BASE(28, 29, IOCFG_RT_BASE, 0x40, 0x10, 19, 1),
+ PIN_FIELD_BASE(30, 30, IOCFG_RT_BASE, 0x40, 0x10, 23, 1),
+ PIN_FIELD_BASE(31, 31, IOCFG_RT_BASE, 0x40, 0x10, 22, 1),
+ PIN_FIELD_BASE(32, 32, IOCFG_RT_BASE, 0x40, 0x10, 21, 1),
+ PIN_FIELD_BASE(33, 33, IOCFG_LT_BASE, 0x30, 0x10, 4, 1),
+ PIN_FIELD_BASE(34, 34, IOCFG_LT_BASE, 0x30, 0x10, 8, 1),
+ PIN_FIELD_BASE(35, 35, IOCFG_LT_BASE, 0x30, 0x10, 7, 1),
+ PIN_FIELD_BASE(36, 37, IOCFG_LT_BASE, 0x30, 0x10, 5, 1),
+ PIN_FIELD_BASE(38, 38, IOCFG_LT_BASE, 0x30, 0x10, 9, 1),
+ PIN_FIELD_BASE(39, 40, IOCFG_RB_BASE, 0x60, 0x10, 18, 1),
+ PIN_FIELD_BASE(41, 41, IOCFG_RB_BASE, 0x60, 0x10, 12, 1),
+ PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0x60, 0x10, 22, 1),
+ PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0x60, 0x10, 20, 1),
+ PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0x60, 0x10, 26, 1),
+ PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0x60, 0x10, 24, 1),
+ PIN_FIELD_BASE(50, 57, IOCFG_RT_BASE, 0x40, 0x10, 2, 1),
+ PIN_FIELD_BASE(58, 58, IOCFG_RT_BASE, 0x40, 0x10, 1, 1),
+ PIN_FIELD_BASE(59, 59, IOCFG_RT_BASE, 0x40, 0x10, 0, 1),
+ PIN_FIELD_BASE(60, 61, IOCFG_RT_BASE, 0x40, 0x10, 10, 1),
+ PIN_FIELD_BASE(62, 62, IOCFG_RB_BASE, 0x60, 0x10, 15, 1),
+ PIN_FIELD_BASE(63, 63, IOCFG_RB_BASE, 0x60, 0x10, 14, 1),
+ PIN_FIELD_BASE(64, 64, IOCFG_RB_BASE, 0x60, 0x10, 13, 1),
+ PIN_FIELD_BASE(65, 65, IOCFG_RB_BASE, 0x60, 0x10, 16, 1),
+ PIN_FIELD_BASE(66, 68, IOCFG_LB_BASE, 0x40, 0x10, 2, 1),
+};
+
+static const struct mtk_pin_field_calc mt7986_pin_r0_range[] = {
+ PIN_FIELD_BASE(0, 0, IOCFG_RB_BASE, 0x70, 0x10, 17, 1),
+ PIN_FIELD_BASE(1, 2, IOCFG_LT_BASE, 0x40, 0x10, 10, 1),
+ PIN_FIELD_BASE(3, 4, IOCFG_LB_BASE, 0x50, 0x10, 0, 1),
+ PIN_FIELD_BASE(5, 6, IOCFG_RB_BASE, 0x70, 0x10, 0, 1),
+ PIN_FIELD_BASE(7, 10, IOCFG_LT_BASE, 0x40, 0x10, 0, 1),
+ PIN_FIELD_BASE(11, 14, IOCFG_RB_BASE, 0x70, 0x10, 8, 1),
+ PIN_FIELD_BASE(15, 20, IOCFG_RB_BASE, 0x70, 0x10, 2, 1),
+ PIN_FIELD_BASE(21, 23, IOCFG_RT_BASE, 0x50, 0x10, 12, 1),
+ PIN_FIELD_BASE(24, 24, IOCFG_RT_BASE, 0x50, 0x10, 18, 1),
+ PIN_FIELD_BASE(25, 25, IOCFG_RT_BASE, 0x50, 0x10, 17, 1),
+ PIN_FIELD_BASE(26, 27, IOCFG_RT_BASE, 0x50, 0x10, 15, 1),
+ PIN_FIELD_BASE(28, 29, IOCFG_RT_BASE, 0x50, 0x10, 19, 1),
+ PIN_FIELD_BASE(30, 30, IOCFG_RT_BASE, 0x50, 0x10, 23, 1),
+ PIN_FIELD_BASE(31, 31, IOCFG_RT_BASE, 0x50, 0x10, 22, 1),
+ PIN_FIELD_BASE(32, 32, IOCFG_RT_BASE, 0x50, 0x10, 21, 1),
+ PIN_FIELD_BASE(33, 33, IOCFG_LT_BASE, 0x40, 0x10, 4, 1),
+ PIN_FIELD_BASE(34, 34, IOCFG_LT_BASE, 0x40, 0x10, 8, 1),
+ PIN_FIELD_BASE(35, 35, IOCFG_LT_BASE, 0x40, 0x10, 7, 1),
+ PIN_FIELD_BASE(36, 37, IOCFG_LT_BASE, 0x40, 0x10, 5, 1),
+ PIN_FIELD_BASE(38, 38, IOCFG_LT_BASE, 0x40, 0x10, 9, 1),
+ PIN_FIELD_BASE(39, 40, IOCFG_RB_BASE, 0x70, 0x10, 18, 1),
+ PIN_FIELD_BASE(41, 41, IOCFG_RB_BASE, 0x70, 0x10, 12, 1),
+ PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0x70, 0x10, 22, 1),
+ PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0x70, 0x10, 20, 1),
+ PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0x70, 0x10, 26, 1),
+ PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0x70, 0x10, 24, 1),
+ PIN_FIELD_BASE(50, 57, IOCFG_RT_BASE, 0x50, 0x10, 2, 1),
+ PIN_FIELD_BASE(58, 58, IOCFG_RT_BASE, 0x50, 0x10, 1, 1),
+ PIN_FIELD_BASE(59, 59, IOCFG_RT_BASE, 0x50, 0x10, 0, 1),
+ PIN_FIELD_BASE(60, 61, IOCFG_RT_BASE, 0x50, 0x10, 10, 1),
+ PIN_FIELD_BASE(62, 62, IOCFG_RB_BASE, 0x70, 0x10, 15, 1),
+ PIN_FIELD_BASE(63, 63, IOCFG_RB_BASE, 0x70, 0x10, 14, 1),
+ PIN_FIELD_BASE(64, 64, IOCFG_RB_BASE, 0x70, 0x10, 13, 1),
+ PIN_FIELD_BASE(65, 65, IOCFG_RB_BASE, 0x70, 0x10, 16, 1),
+ PIN_FIELD_BASE(66, 68, IOCFG_LB_BASE, 0x50, 0x10, 2, 1),
+};
+
+static const struct mtk_pin_field_calc mt7986_pin_r1_range[] = {
+ PIN_FIELD_BASE(0, 0, IOCFG_RB_BASE, 0x80, 0x10, 17, 1),
+ PIN_FIELD_BASE(1, 2, IOCFG_LT_BASE, 0x50, 0x10, 10, 1),
+ PIN_FIELD_BASE(3, 4, IOCFG_LB_BASE, 0x60, 0x10, 0, 1),
+ PIN_FIELD_BASE(5, 6, IOCFG_RB_BASE, 0x80, 0x10, 0, 1),
+ PIN_FIELD_BASE(7, 10, IOCFG_LT_BASE, 0x50, 0x10, 0, 1),
+ PIN_FIELD_BASE(11, 14, IOCFG_RB_BASE, 0x80, 0x10, 8, 1),
+ PIN_FIELD_BASE(15, 20, IOCFG_RB_BASE, 0x80, 0x10, 2, 1),
+ PIN_FIELD_BASE(21, 23, IOCFG_RT_BASE, 0x60, 0x10, 12, 1),
+ PIN_FIELD_BASE(24, 24, IOCFG_RT_BASE, 0x60, 0x10, 18, 1),
+ PIN_FIELD_BASE(25, 25, IOCFG_RT_BASE, 0x60, 0x10, 17, 1),
+ PIN_FIELD_BASE(26, 27, IOCFG_RT_BASE, 0x60, 0x10, 15, 1),
+ PIN_FIELD_BASE(28, 29, IOCFG_RT_BASE, 0x60, 0x10, 19, 1),
+ PIN_FIELD_BASE(30, 30, IOCFG_RT_BASE, 0x60, 0x10, 23, 1),
+ PIN_FIELD_BASE(31, 31, IOCFG_RT_BASE, 0x60, 0x10, 22, 1),
+ PIN_FIELD_BASE(32, 32, IOCFG_RT_BASE, 0x60, 0x10, 21, 1),
+ PIN_FIELD_BASE(33, 33, IOCFG_LT_BASE, 0x50, 0x10, 4, 1),
+ PIN_FIELD_BASE(34, 34, IOCFG_LT_BASE, 0x50, 0x10, 8, 1),
+ PIN_FIELD_BASE(35, 35, IOCFG_LT_BASE, 0x50, 0x10, 7, 1),
+ PIN_FIELD_BASE(36, 37, IOCFG_LT_BASE, 0x50, 0x10, 5, 1),
+ PIN_FIELD_BASE(38, 38, IOCFG_LT_BASE, 0x50, 0x10, 9, 1),
+ PIN_FIELD_BASE(39, 40, IOCFG_RB_BASE, 0x80, 0x10, 18, 1),
+ PIN_FIELD_BASE(41, 41, IOCFG_RB_BASE, 0x80, 0x10, 12, 1),
+ PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0x80, 0x10, 22, 1),
+ PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0x80, 0x10, 20, 1),
+ PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0x80, 0x10, 26, 1),
+ PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0x80, 0x10, 24, 1),
+ PIN_FIELD_BASE(50, 57, IOCFG_RT_BASE, 0x60, 0x10, 2, 1),
+ PIN_FIELD_BASE(58, 58, IOCFG_RT_BASE, 0x60, 0x10, 1, 1),
+ PIN_FIELD_BASE(59, 59, IOCFG_RT_BASE, 0x60, 0x10, 0, 1),
+ PIN_FIELD_BASE(60, 61, IOCFG_RT_BASE, 0x60, 0x10, 10, 1),
+ PIN_FIELD_BASE(62, 62, IOCFG_RB_BASE, 0x80, 0x10, 15, 1),
+ PIN_FIELD_BASE(63, 63, IOCFG_RB_BASE, 0x80, 0x10, 14, 1),
+ PIN_FIELD_BASE(64, 64, IOCFG_RB_BASE, 0x80, 0x10, 13, 1),
+ PIN_FIELD_BASE(65, 65, IOCFG_RB_BASE, 0x80, 0x10, 16, 1),
+ PIN_FIELD_BASE(66, 68, IOCFG_LB_BASE, 0x60, 0x10, 2, 1),
+};
+
+static const struct mtk_pin_reg_calc mt7986_reg_cals[] = {
+ [PINCTRL_PIN_REG_MODE] = MTK_RANGE(mt7986_pin_mode_range),
+ [PINCTRL_PIN_REG_DIR] = MTK_RANGE(mt7986_pin_dir_range),
+ [PINCTRL_PIN_REG_DI] = MTK_RANGE(mt7986_pin_di_range),
+ [PINCTRL_PIN_REG_DO] = MTK_RANGE(mt7986_pin_do_range),
+ [PINCTRL_PIN_REG_SMT] = MTK_RANGE(mt7986_pin_smt_range),
+ [PINCTRL_PIN_REG_IES] = MTK_RANGE(mt7986_pin_ies_range),
+ [PINCTRL_PIN_REG_DRV] = MTK_RANGE(mt7986_pin_drv_range),
+ [PINCTRL_PIN_REG_PU] = MTK_RANGE(mt7986_pin_pu_range),
+ [PINCTRL_PIN_REG_PD] = MTK_RANGE(mt7986_pin_pd_range),
+ [PINCTRL_PIN_REG_PUPD] = MTK_RANGE(mt7986_pin_pupd_range),
+ [PINCTRL_PIN_REG_R0] = MTK_RANGE(mt7986_pin_r0_range),
+ [PINCTRL_PIN_REG_R1] = MTK_RANGE(mt7986_pin_r1_range),
+};
+
+static const struct mtk_pin_desc mt7986a_pins[] = {
+ MT7986_PIN(0, "SYS_WATCHDOG"),
+ MT7986_PIN(1, "WF2G_LED"),
+ MT7986_PIN(2, "WF5G_LED"),
+ MT7986_PIN(3, "I2C_SCL"),
+ MT7986_PIN(4, "I2C_SDA"),
+ MT7986_PIN(5, "GPIO_0"),
+ MT7986_PIN(6, "GPIO_1"),
+ MT7986_PIN(7, "GPIO_2"),
+ MT7986_PIN(8, "GPIO_3"),
+ MT7986_PIN(9, "GPIO_4"),
+ MT7986_PIN(10, "GPIO_5"),
+ MT7986_PIN(11, "GPIO_6"),
+ MT7986_PIN(12, "GPIO_7"),
+ MT7986_PIN(13, "GPIO_8"),
+ MT7986_PIN(14, "GPIO_9"),
+ MT7986_PIN(15, "GPIO_10"),
+ MT7986_PIN(16, "GPIO_11"),
+ MT7986_PIN(17, "GPIO_12"),
+ MT7986_PIN(18, "GPIO_13"),
+ MT7986_PIN(19, "GPIO_14"),
+ MT7986_PIN(20, "GPIO_15"),
+ MT7986_PIN(21, "PWM0"),
+ MT7986_PIN(22, "PWM1"),
+ MT7986_PIN(23, "SPI0_CLK"),
+ MT7986_PIN(24, "SPI0_MOSI"),
+ MT7986_PIN(25, "SPI0_MISO"),
+ MT7986_PIN(26, "SPI0_CS"),
+ MT7986_PIN(27, "SPI0_HOLD"),
+ MT7986_PIN(28, "SPI0_WP"),
+ MT7986_PIN(29, "SPI1_CLK"),
+ MT7986_PIN(30, "SPI1_MOSI"),
+ MT7986_PIN(31, "SPI1_MISO"),
+ MT7986_PIN(32, "SPI1_CS"),
+ MT7986_PIN(33, "SPI2_CLK"),
+ MT7986_PIN(34, "SPI2_MOSI"),
+ MT7986_PIN(35, "SPI2_MISO"),
+ MT7986_PIN(36, "SPI2_CS"),
+ MT7986_PIN(37, "SPI2_HOLD"),
+ MT7986_PIN(38, "SPI2_WP"),
+ MT7986_PIN(39, "UART0_RXD"),
+ MT7986_PIN(40, "UART0_TXD"),
+ MT7986_PIN(41, "PCIE_PERESET_N"),
+ MT7986_PIN(42, "UART1_RXD"),
+ MT7986_PIN(43, "UART1_TXD"),
+ MT7986_PIN(44, "UART1_CTS"),
+ MT7986_PIN(45, "UART1_RTS"),
+ MT7986_PIN(46, "UART2_RXD"),
+ MT7986_PIN(47, "UART2_TXD"),
+ MT7986_PIN(48, "UART2_CTS"),
+ MT7986_PIN(49, "UART2_RTS"),
+ MT7986_PIN(50, "EMMC_DATA_0"),
+ MT7986_PIN(51, "EMMC_DATA_1"),
+ MT7986_PIN(52, "EMMC_DATA_2"),
+ MT7986_PIN(53, "EMMC_DATA_3"),
+ MT7986_PIN(54, "EMMC_DATA_4"),
+ MT7986_PIN(55, "EMMC_DATA_5"),
+ MT7986_PIN(56, "EMMC_DATA_6"),
+ MT7986_PIN(57, "EMMC_DATA_7"),
+ MT7986_PIN(58, "EMMC_CMD"),
+ MT7986_PIN(59, "EMMC_CK"),
+ MT7986_PIN(60, "EMMC_DSL"),
+ MT7986_PIN(61, "EMMC_RSTB"),
+ MT7986_PIN(62, "PCM_DTX"),
+ MT7986_PIN(63, "PCM_DRX"),
+ MT7986_PIN(64, "PCM_CLK"),
+ MT7986_PIN(65, "PCM_FS"),
+ MT7986_PIN(66, "MT7531_INT"),
+ MT7986_PIN(67, "SMI_MDC"),
+ MT7986_PIN(68, "SMI_MDIO"),
+ MT7986_PIN(69, "WF0_DIG_RESETB"),
+ MT7986_PIN(70, "WF0_CBA_RESETB"),
+ MT7986_PIN(71, "WF0_XO_REQ"),
+ MT7986_PIN(72, "WF0_TOP_CLK"),
+ MT7986_PIN(73, "WF0_TOP_DATA"),
+ MT7986_PIN(74, "WF0_HB1"),
+ MT7986_PIN(75, "WF0_HB2"),
+ MT7986_PIN(76, "WF0_HB3"),
+ MT7986_PIN(77, "WF0_HB4"),
+ MT7986_PIN(78, "WF0_HB0"),
+ MT7986_PIN(79, "WF0_HB0_B"),
+ MT7986_PIN(80, "WF0_HB5"),
+ MT7986_PIN(81, "WF0_HB6"),
+ MT7986_PIN(82, "WF0_HB7"),
+ MT7986_PIN(83, "WF0_HB8"),
+ MT7986_PIN(84, "WF0_HB9"),
+ MT7986_PIN(85, "WF0_HB10"),
+ MT7986_PIN(86, "WF1_DIG_RESETB"),
+ MT7986_PIN(87, "WF1_CBA_RESETB"),
+ MT7986_PIN(88, "WF1_XO_REQ"),
+ MT7986_PIN(89, "WF1_TOP_CLK"),
+ MT7986_PIN(90, "WF1_TOP_DATA"),
+ MT7986_PIN(91, "WF1_HB1"),
+ MT7986_PIN(92, "WF1_HB2"),
+ MT7986_PIN(93, "WF1_HB3"),
+ MT7986_PIN(94, "WF1_HB4"),
+ MT7986_PIN(95, "WF1_HB0"),
+ MT7986_PIN(96, "WF1_HB0_B"),
+ MT7986_PIN(97, "WF1_HB5"),
+ MT7986_PIN(98, "WF1_HB6"),
+ MT7986_PIN(99, "WF1_HB7"),
+ MT7986_PIN(100, "WF1_HB8"),
+};
+
+static const struct mtk_pin_desc mt7986b_pins[] = {
+ MT7986_PIN(0, "SYS_WATCHDOG"),
+ MT7986_PIN(1, "WF2G_LED"),
+ MT7986_PIN(2, "WF5G_LED"),
+ MT7986_PIN(3, "I2C_SCL"),
+ MT7986_PIN(4, "I2C_SDA"),
+ MT7986_PIN(5, "GPIO_0"),
+ MT7986_PIN(6, "GPIO_1"),
+ MT7986_PIN(7, "GPIO_2"),
+ MT7986_PIN(8, "GPIO_3"),
+ MT7986_PIN(9, "GPIO_4"),
+ MT7986_PIN(10, "GPIO_5"),
+ MT7986_PIN(11, "GPIO_6"),
+ MT7986_PIN(12, "GPIO_7"),
+ MT7986_PIN(13, "GPIO_8"),
+ MT7986_PIN(14, "GPIO_9"),
+ MT7986_PIN(15, "GPIO_10"),
+ MT7986_PIN(16, "GPIO_11"),
+ MT7986_PIN(17, "GPIO_12"),
+ MT7986_PIN(18, "GPIO_13"),
+ MT7986_PIN(19, "GPIO_14"),
+ MT7986_PIN(20, "GPIO_15"),
+ MT7986_PIN(21, "PWM0"),
+ MT7986_PIN(22, "PWM1"),
+ MT7986_PIN(23, "SPI0_CLK"),
+ MT7986_PIN(24, "SPI0_MOSI"),
+ MT7986_PIN(25, "SPI0_MISO"),
+ MT7986_PIN(26, "SPI0_CS"),
+ MT7986_PIN(27, "SPI0_HOLD"),
+ MT7986_PIN(28, "SPI0_WP"),
+ MT7986_PIN(29, "SPI1_CLK"),
+ MT7986_PIN(30, "SPI1_MOSI"),
+ MT7986_PIN(31, "SPI1_MISO"),
+ MT7986_PIN(32, "SPI1_CS"),
+ MT7986_PIN(33, "SPI2_CLK"),
+ MT7986_PIN(34, "SPI2_MOSI"),
+ MT7986_PIN(35, "SPI2_MISO"),
+ MT7986_PIN(36, "SPI2_CS"),
+ MT7986_PIN(37, "SPI2_HOLD"),
+ MT7986_PIN(38, "SPI2_WP"),
+ MT7986_PIN(39, "UART0_RXD"),
+ MT7986_PIN(40, "UART0_TXD"),
+ MT7986_NOT_BALLOUT_PIN(41),
+ MT7986_NOT_BALLOUT_PIN(42),
+ MT7986_NOT_BALLOUT_PIN(43),
+ MT7986_NOT_BALLOUT_PIN(44),
+ MT7986_NOT_BALLOUT_PIN(45),
+ MT7986_NOT_BALLOUT_PIN(46),
+ MT7986_NOT_BALLOUT_PIN(47),
+ MT7986_NOT_BALLOUT_PIN(48),
+ MT7986_NOT_BALLOUT_PIN(49),
+ MT7986_NOT_BALLOUT_PIN(50),
+ MT7986_NOT_BALLOUT_PIN(51),
+ MT7986_NOT_BALLOUT_PIN(52),
+ MT7986_NOT_BALLOUT_PIN(53),
+ MT7986_NOT_BALLOUT_PIN(54),
+ MT7986_NOT_BALLOUT_PIN(55),
+ MT7986_NOT_BALLOUT_PIN(56),
+ MT7986_NOT_BALLOUT_PIN(57),
+ MT7986_NOT_BALLOUT_PIN(58),
+ MT7986_NOT_BALLOUT_PIN(59),
+ MT7986_NOT_BALLOUT_PIN(60),
+ MT7986_NOT_BALLOUT_PIN(61),
+ MT7986_NOT_BALLOUT_PIN(62),
+ MT7986_NOT_BALLOUT_PIN(63),
+ MT7986_NOT_BALLOUT_PIN(64),
+ MT7986_NOT_BALLOUT_PIN(65),
+ MT7986_PIN(66, "MT7531_INT"),
+ MT7986_PIN(67, "SMI_MDC"),
+ MT7986_PIN(68, "SMI_MDIO"),
+ MT7986_PIN(69, "WF0_DIG_RESETB"),
+ MT7986_PIN(70, "WF0_CBA_RESETB"),
+ MT7986_PIN(71, "WF0_XO_REQ"),
+ MT7986_PIN(72, "WF0_TOP_CLK"),
+ MT7986_PIN(73, "WF0_TOP_DATA"),
+ MT7986_PIN(74, "WF0_HB1"),
+ MT7986_PIN(75, "WF0_HB2"),
+ MT7986_PIN(76, "WF0_HB3"),
+ MT7986_PIN(77, "WF0_HB4"),
+ MT7986_PIN(78, "WF0_HB0"),
+ MT7986_PIN(79, "WF0_HB0_B"),
+ MT7986_PIN(80, "WF0_HB5"),
+ MT7986_PIN(81, "WF0_HB6"),
+ MT7986_PIN(82, "WF0_HB7"),
+ MT7986_PIN(83, "WF0_HB8"),
+ MT7986_PIN(84, "WF0_HB9"),
+ MT7986_PIN(85, "WF0_HB10"),
+ MT7986_PIN(86, "WF1_DIG_RESETB"),
+ MT7986_PIN(87, "WF1_CBA_RESETB"),
+ MT7986_PIN(88, "WF1_XO_REQ"),
+ MT7986_PIN(89, "WF1_TOP_CLK"),
+ MT7986_PIN(90, "WF1_TOP_DATA"),
+ MT7986_PIN(91, "WF1_HB1"),
+ MT7986_PIN(92, "WF1_HB2"),
+ MT7986_PIN(93, "WF1_HB3"),
+ MT7986_PIN(94, "WF1_HB4"),
+ MT7986_PIN(95, "WF1_HB0"),
+ MT7986_PIN(96, "WF1_HB0_B"),
+ MT7986_PIN(97, "WF1_HB5"),
+ MT7986_PIN(98, "WF1_HB6"),
+ MT7986_PIN(99, "WF1_HB7"),
+ MT7986_PIN(100, "WF1_HB8"),
+};
+
+/* List all groups consisting of these pins dedicated to the enablement of
+ * certain hardware block and the corresponding mode for all of the pins.
+ * The hardware probably has multiple combinations of these pinouts.
+ */
+
+static int mt7986_watchdog_pins[] = { 0, };
+static int mt7986_watchdog_funcs[] = { 1, };
+
+static int mt7986_wifi_led_pins[] = { 1, 2, };
+static int mt7986_wifi_led_funcs[] = { 1, 1, };
+
+static int mt7986_i2c_pins[] = { 3, 4, };
+static int mt7986_i2c_funcs[] = { 1, 1, };
+
+static int mt7986_uart1_0_pins[] = { 7, 8, 9, 10, };
+static int mt7986_uart1_0_funcs[] = { 3, 3, 3, 3, };
+
+static int mt7986_spi1_0_pins[] = { 11, 12, 13, 14, };
+static int mt7986_spi1_0_funcs[] = { 3, 3, 3, 3, };
+
+static int mt7986_pwm1_1_pins[] = { 20, };
+static int mt7986_pwm1_1_funcs[] = { 2, };
+
+static int mt7986_pwm0_pins[] = { 21, };
+static int mt7986_pwm0_funcs[] = { 1, };
+
+static int mt7986_pwm1_0_pins[] = { 22, };
+static int mt7986_pwm1_0_funcs[] = { 1, };
+
+static int mt7986_emmc_45_pins[] = {
+ 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, };
+static int mt7986_emmc_45_funcs[] = { 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, };
+
+static int mt7986_snfi_pins[] = { 23, 24, 25, 26, 27, 28, };
+static int mt7986_snfi_funcs[] = { 1, 1, 1, 1, 1, 1, };
+
+static int mt7986_spi1_1_pins[] = { 23, 24, 25, 26, };
+static int mt7986_spi1_1_funcs[] = { 3, 3, 3, 3, };
+
+static int mt7986_uart1_1_pins[] = { 23, 24, 25, 26, };
+static int mt7986_uart1_1_funcs[] = { 4, 4, 4, 4, };
+
+static int mt7986_spi1_2_pins[] = { 29, 30, 31, 32, };
+static int mt7986_spi1_2_funcs[] = { 1, 1, 1, 1, };
+
+static int mt7986_uart1_2_pins[] = { 29, 30, 31, 32, };
+static int mt7986_uart1_2_funcs[] = { 3, 3, 3, 3, };
+
+static int mt7986_uart2_0_pins[] = { 29, 30, 31, 32, };
+static int mt7986_uart2_0_funcs[] = { 4, 4, 4, 4, };
+
+static int mt7986_spi0_pins[] = { 33, 34, 35, 36, };
+static int mt7986_spi0_funcs[] = { 1, 1, 1, 1, };
+
+static int mt7986_spi0_wp_hold_pins[] = { 37, 38, };
+static int mt7986_spi0_wp_hold_funcs[] = { 1, 1, };
+
+static int mt7986_uart2_1_pins[] = { 33, 34, 35, 36, };
+static int mt7986_uart2_1_funcs[] = { 3, 3, 3, 3, };
+
+static int mt7986_uart1_3_rx_tx_pins[] = { 35, 36, };
+static int mt7986_uart1_3_rx_tx_funcs[] = { 2, 2, };
+
+static int mt7986_uart1_3_cts_rts_pins[] = { 37, 38, };
+static int mt7986_uart1_3_cts_rts_funcs[] = { 2, 2, };
+
+static int mt7986_spi1_3_pins[] = { 33, 34, 35, 36, };
+static int mt7986_spi1_3_funcs[] = { 4, 4, 4, 4, };
+
+static int mt7986_uart0_pins[] = { 39, 40, };
+static int mt7986_uart0_funcs[] = { 1, 1, };
+
+static int mt7986_pcie_reset_pins[] = { 41, };
+static int mt7986_pcie_reset_funcs[] = { 1, };
+
+static int mt7986_uart1_pins[] = { 42, 43, 44, 45, };
+static int mt7986_uart1_funcs[] = { 1, 1, 1, 1, };
+
+static int mt7986_uart2_pins[] = { 46, 47, 48, 49, };
+static int mt7986_uart2_funcs[] = { 1, 1, 1, 1, };
+
+static int mt7986_emmc_51_pins[] = {
+ 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, };
+static int mt7986_emmc_51_funcs[] = { 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, };
+
+static int mt7986_pcm_pins[] = { 62, 63, 64, 65, };
+static int mt7986_pcm_funcs[] = { 1, 1, 1, 1, };
+
+static int mt7986_i2s_pins[] = { 62, 63, 64, 65, };
+static int mt7986_i2s_funcs[] = { 1, 1, 1, 1, };
+
+static int mt7986_switch_int_pins[] = { 66, };
+static int mt7986_switch_int_funcs[] = { 1, };
+
+static int mt7986_mdc_mdio_pins[] = { 67, 68, };
+static int mt7986_mdc_mdio_funcs[] = { 1, 1, };
+
+static int mt7986_wf_2g_pins[] = {74, 75, 76, 77, 78, 79, 80, 81, 82, 83, };
+static int mt7986_wf_2g_funcs[] = {1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, };
+
+static int mt7986_wf_5g_pins[] = {91, 92, 93, 94, 95, 96, 97, 98, 99, 100, };
+static int mt7986_wf_5g_funcs[] = {1, 1, 1, 1, 1, 1, 1, 1, 1, 1, };
+
+static int mt7986_wf_dbdc_pins[] = {
+ 74, 75, 76, 77, 78, 79, 80, 81, 82, 83, 84, 85, };
+static int mt7986_wf_dbdc_funcs[] = {
+ 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, };
+
+static int mt7986_pcie_clk_pins[] = { 9, };
+static int mt7986_pcie_clk_funcs[] = { 1, };
+
+static int mt7986_pcie_wake_pins[] = { 10, };
+static int mt7986_pcie_wake_funcs[] = { 1, };
+
+static const struct group_desc mt7986_groups[] = {
+ PINCTRL_PIN_GROUP("watchdog", mt7986_watchdog),
+ PINCTRL_PIN_GROUP("wifi_led", mt7986_wifi_led),
+ PINCTRL_PIN_GROUP("i2c", mt7986_i2c),
+ PINCTRL_PIN_GROUP("uart1_0", mt7986_uart1_0),
+ PINCTRL_PIN_GROUP("pcie_clk", mt7986_pcie_clk),
+ PINCTRL_PIN_GROUP("pcie_wake", mt7986_pcie_wake),
+ PINCTRL_PIN_GROUP("spi1_0", mt7986_spi1_0),
+ PINCTRL_PIN_GROUP("pwm1_1", mt7986_pwm1_1),
+ PINCTRL_PIN_GROUP("pwm0", mt7986_pwm0),
+ PINCTRL_PIN_GROUP("pwm1_0", mt7986_pwm1_0),
+ PINCTRL_PIN_GROUP("emmc_45", mt7986_emmc_45),
+ PINCTRL_PIN_GROUP("snfi", mt7986_snfi),
+ PINCTRL_PIN_GROUP("spi1_1", mt7986_spi1_1),
+ PINCTRL_PIN_GROUP("uart1_1", mt7986_uart1_1),
+ PINCTRL_PIN_GROUP("spi1_2", mt7986_spi1_2),
+ PINCTRL_PIN_GROUP("uart1_2", mt7986_uart1_2),
+ PINCTRL_PIN_GROUP("uart2_0", mt7986_uart2_0),
+ PINCTRL_PIN_GROUP("spi0", mt7986_spi0),
+ PINCTRL_PIN_GROUP("spi0_wp_hold", mt7986_spi0_wp_hold),
+ PINCTRL_PIN_GROUP("uart2_1", mt7986_uart2_1),
+ PINCTRL_PIN_GROUP("uart1_3_rx_tx", mt7986_uart1_3_rx_tx),
+ PINCTRL_PIN_GROUP("uart1_3_cts_rts", mt7986_uart1_3_cts_rts),
+ PINCTRL_PIN_GROUP("spi1_3", mt7986_spi1_3),
+ PINCTRL_PIN_GROUP("uart0", mt7986_uart0),
+ PINCTRL_PIN_GROUP("switch_int", mt7986_switch_int),
+ PINCTRL_PIN_GROUP("mdc_mdio", mt7986_mdc_mdio),
+ PINCTRL_PIN_GROUP("pcie_pereset", mt7986_pcie_reset),
+ PINCTRL_PIN_GROUP("uart1", mt7986_uart1),
+ PINCTRL_PIN_GROUP("uart2", mt7986_uart2),
+ PINCTRL_PIN_GROUP("emmc_51", mt7986_emmc_51),
+ PINCTRL_PIN_GROUP("pcm", mt7986_pcm),
+ PINCTRL_PIN_GROUP("i2s", mt7986_i2s),
+ PINCTRL_PIN_GROUP("wf_2g", mt7986_wf_2g),
+ PINCTRL_PIN_GROUP("wf_5g", mt7986_wf_5g),
+ PINCTRL_PIN_GROUP("wf_dbdc", mt7986_wf_dbdc),
+};
+
+/* Joint those groups owning the same capability in user point of view which
+ * allows that people tend to use through the device tree.
+ */
+
+static const char *mt7986_audio_groups[] = { "pcm", "i2s" };
+static const char *mt7986_emmc_groups[] = {
+ "emmc_45", "emmc_51", };
+static const char *mt7986_ethernet_groups[] = {
+ "switch_int", "mdc_mdio", };
+static const char *mt7986_i2c_groups[] = { "i2c", };
+static const char *mt7986_led_groups[] = { "wifi_led", };
+static const char *mt7986_flash_groups[] = { "snfi", };
+static const char *mt7986_pcie_groups[] = {
+ "pcie_clk", "pcie_wake", "pcie_pereset" };
+static const char *mt7986_pwm_groups[] = { "pwm0", "pwm1_0", "pwm1_1", };
+static const char *mt7986_spi_groups[] = {
+ "spi0", "spi0_wp_hold", "spi1_0", "spi1_1", "spi1_2", "spi1_3", };
+static const char *mt7986_uart_groups[] = {
+ "uart1_0", "uart1_1", "uart1_2", "uart1_3_rx_tx", "uart1_3_cts_rts",
+ "uart2_0", "uart2_1", "uart0", "uart1", "uart2",
+};
+static const char *mt7986_wdt_groups[] = { "watchdog", };
+static const char *mt7986_wf_groups[] = { "wf_2g", "wf_5g", "wf_dbdc", };
+
+static const struct function_desc mt7986_functions[] = {
+ {"audio", mt7986_audio_groups, ARRAY_SIZE(mt7986_audio_groups)},
+ {"emmc", mt7986_emmc_groups, ARRAY_SIZE(mt7986_emmc_groups)},
+ {"eth", mt7986_ethernet_groups, ARRAY_SIZE(mt7986_ethernet_groups)},
+ {"i2c", mt7986_i2c_groups, ARRAY_SIZE(mt7986_i2c_groups)},
+ {"led", mt7986_led_groups, ARRAY_SIZE(mt7986_led_groups)},
+ {"flash", mt7986_flash_groups, ARRAY_SIZE(mt7986_flash_groups)},
+ {"pcie", mt7986_pcie_groups, ARRAY_SIZE(mt7986_pcie_groups)},
+ {"pwm", mt7986_pwm_groups, ARRAY_SIZE(mt7986_pwm_groups)},
+ {"spi", mt7986_spi_groups, ARRAY_SIZE(mt7986_spi_groups)},
+ {"uart", mt7986_uart_groups, ARRAY_SIZE(mt7986_uart_groups)},
+ {"watchdog", mt7986_wdt_groups, ARRAY_SIZE(mt7986_wdt_groups)},
+ {"wifi", mt7986_wf_groups, ARRAY_SIZE(mt7986_wf_groups)},
+};
+
+static const struct mtk_eint_hw mt7986a_eint_hw = {
+ .port_mask = 7,
+ .ports = 7,
+ .ap_num = ARRAY_SIZE(mt7986a_pins),
+ .db_cnt = 16,
+};
+
+static const struct mtk_eint_hw mt7986b_eint_hw = {
+ .port_mask = 7,
+ .ports = 7,
+ .ap_num = ARRAY_SIZE(mt7986b_pins),
+ .db_cnt = 16,
+};
+
+static struct mtk_pin_soc mt7986a_data = {
+ .reg_cal = mt7986_reg_cals,
+ .pins = mt7986a_pins,
+ .npins = ARRAY_SIZE(mt7986a_pins),
+ .grps = mt7986_groups,
+ .ngrps = ARRAY_SIZE(mt7986_groups),
+ .funcs = mt7986_functions,
+ .nfuncs = ARRAY_SIZE(mt7986_functions),
+ .eint_hw = &mt7986a_eint_hw,
+ .gpio_m = 0,
+ .ies_present = false,
+ .base_names = mt7986_pinctrl_register_base_names,
+ .nbase_names = ARRAY_SIZE(mt7986_pinctrl_register_base_names),
+ .bias_set_combo = mtk_pinconf_bias_set_combo,
+ .bias_get_combo = mtk_pinconf_bias_get_combo,
+ .drive_set = mtk_pinconf_drive_set_rev1,
+ .drive_get = mtk_pinconf_drive_get_rev1,
+ .adv_pull_get = mtk_pinconf_adv_pull_get,
+ .adv_pull_set = mtk_pinconf_adv_pull_set,
+};
+
+static struct mtk_pin_soc mt7986b_data = {
+ .reg_cal = mt7986_reg_cals,
+ .pins = mt7986b_pins,
+ .npins = ARRAY_SIZE(mt7986b_pins),
+ .grps = mt7986_groups,
+ .ngrps = ARRAY_SIZE(mt7986_groups),
+ .funcs = mt7986_functions,
+ .nfuncs = ARRAY_SIZE(mt7986_functions),
+ .eint_hw = &mt7986b_eint_hw,
+ .gpio_m = 0,
+ .ies_present = false,
+ .base_names = mt7986_pinctrl_register_base_names,
+ .nbase_names = ARRAY_SIZE(mt7986_pinctrl_register_base_names),
+ .bias_set_combo = mtk_pinconf_bias_set_combo,
+ .bias_get_combo = mtk_pinconf_bias_get_combo,
+ .drive_set = mtk_pinconf_drive_set_rev1,
+ .drive_get = mtk_pinconf_drive_get_rev1,
+ .adv_pull_get = mtk_pinconf_adv_pull_get,
+ .adv_pull_set = mtk_pinconf_adv_pull_set,
+};
+
+static const struct of_device_id mt7986a_pinctrl_of_match[] = {
+ {.compatible = "mediatek,mt7986a-pinctrl",},
+ {}
+};
+
+static const struct of_device_id mt7986b_pinctrl_of_match[] = {
+ {.compatible = "mediatek,mt7986b-pinctrl",},
+ {}
+};
+
+static int mt7986a_pinctrl_probe(struct platform_device *pdev)
+{
+ return mtk_moore_pinctrl_probe(pdev, &mt7986a_data);
+}
+
+static int mt7986b_pinctrl_probe(struct platform_device *pdev)
+{
+ return mtk_moore_pinctrl_probe(pdev, &mt7986b_data);
+}
+
+static struct platform_driver mt7986a_pinctrl_driver = {
+ .driver = {
+ .name = "mt7986a-pinctrl",
+ .of_match_table = mt7986a_pinctrl_of_match,
+ },
+ .probe = mt7986a_pinctrl_probe,
+};
+
+static struct platform_driver mt7986b_pinctrl_driver = {
+ .driver = {
+ .name = "mt7986b-pinctrl",
+ .of_match_table = mt7986b_pinctrl_of_match,
+ },
+ .probe = mt7986b_pinctrl_probe,
+};
+
+static int __init mt7986a_pinctrl_init(void)
+{
+ return platform_driver_register(&mt7986a_pinctrl_driver);
+}
+
+static int __init mt7986b_pinctrl_init(void)
+{
+ return platform_driver_register(&mt7986b_pinctrl_driver);
+}
+
+arch_initcall(mt7986a_pinctrl_init);
+arch_initcall(mt7986b_pinctrl_init);
--
2.29.2
This updates bindings for MT7986 pinctrl driver. The
difference of pinctrl between mt7986a and mt7986b is that pin-41 to pin-65
do not exist on mt7986b
Signed-off-by: Sam Shih <[email protected]>
---
v3 : make mt7986 pinctrl bindings as a separate file
v2 : deleted the redundant description of mt7986a/mt7986b
---
.../pinctrl/mediatek,mt7986-pinctrl.txt | 300 ++++++++++++++++++
1 file changed, 300 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.txt
diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.txt
new file mode 100644
index 000000000000..5805e53d5924
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.txt
@@ -0,0 +1,300 @@
+* Mediatek MT7986 Pin Controller
+
+The Mediatek's Pin controller is used to control SoC pins.
+
+Required properties for the root node:
+ - compatible: Should be one of the following
+ "mediatek,mt7986a-pinctrl" for MT7986a SoC
+ "mediatek,mt7986b-pinctrl" for MT7986b SoC
+ - gpio-controller: Marks the device node as a GPIO controller.
+ - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
+ binding is used, the amount of cells must be specified as 2. See the below
+ mentioned gpio binding representation for description of particular cells.
+ - gpio-ranges : gpio valid number range.
+ - reg: physical address base for gpio base registers. There are 8 GPIO
+ physical address base in mt8183.
+
+Optional properties:
+- reg-names: gpio base register names. There are 8 gpio base register
+ names in mt7986. They are "gpio_base", "iocfg_rt_base", "iocfg_rb_base",
+ "iocfg_lt_base", "iocfg_lb_base", "iocfg_tr_base", "iocfg_tl_base", "eint".
+- interrupt-controller: Marks the device node as an interrupt controller
+
+If the property interrupt-controller is defined, following property is required
+- interrupts : The interrupt outputs to gic.
+- #interrupt-cells: Should be two.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+MT7986 pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive-strength, etc.
+
+We support 2 types of configuration nodes. Those nodes can be either pinmux
+nodes or pinconf nodes. Each configuration node can consist of multiple nodes
+describing the pinmux and pinconf options.
+
+The name of each subnode doesn't matter as long as it is unique; all subnodes
+should be enumerated and processed purely based on their content.
+
+== pinmux nodes content ==
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pinmux subnode:
+
+Required properties are:
+ - groups: An array of strings. Each string contains the name of a group.
+ Valid values for these names are listed below.
+ - function: A string containing the name of the function to mux to the
+ group. Valid values for function names are listed below.
+
+== pinconf nodes content ==
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pinconf subnode:
+
+Required properties are:
+ - pins: An array of strings. Each string contains the name of a pin.
+ Valid values for these names are listed below.
+ - groups: An array of strings. Each string contains the name of a group.
+ Valid values for these names are listed below.
+
+Optional properies are:
+ - GENERIC_PINCONFIG: is the generic pinconfig options to use, bias-disable,
+ bias-pull-down, bias-pull-up, input-enable, input-disable, output-low,
+ output-high, input-schmitt-enable, input-schmitt-disable
+ and drive-strength are valid.
+ Valid arguments for 'drive-strength': 2, 4, 6, 8, 10, 12, 14, 16 in mA.
+ - mediatek,pull-up-adv
+ Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
+ Pull up setings for 2 pull resistors, R0 and R1. User can
+ configure those special pins. Valid arguments are described as below:
+ 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+ 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+ 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+ 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+ - mediatek,pull-down-adv
+ Valid arguments for 'mediatek,pull-down-adv' are '0', '1', '2', '3'
+ Pull down settings for 2 pull resistors, R0 and R1. User can
+ configure those special pins. Valid arguments are described as below:
+ 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+ 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+ 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+ 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+ - mediatek,tdsel: An integer describing the steps for output level shifter duty
+ cycle when asserted (high pulse width adjustment). Valid arguments are from 0
+ to 15.
+ - mediatek,rdsel: An integer describing the steps for input level shifter duty
+ cycle when asserted (high pulse width adjustment). Valid arguments are from 0
+ to 63.
+
+== Valid values for pins, function and groups on MT7986a and MT7986b ==
+
+Valid values for pins are:
+pins can be referenced via the pin names as the below table shown and the
+related physical number is also put ahead of those names which helps cross
+references to pins between groups to know whether pins assignment conflict
+happens among devices try to acquire those available pins.
+
+There is no PIN 41 to PIN 65 on mt7686b, you can only use those pins on mt7986a.
+
+ Pin #: Valid values for pins
+ -----------------------------
+ PIN 0: "SYS_WATCHDOG"
+ PIN 1: "WF2G_LED"
+ PIN 2: "WF5G_LED"
+ PIN 3: "I2C_SCL"
+ PIN 4: "I2C_SDA"
+ PIN 5: "GPIO_0"
+ PIN 6: "GPIO_1"
+ PIN 7: "GPIO_2"
+ PIN 8: "GPIO_3"
+ PIN 9: "GPIO_4"
+ PIN 10: "GPIO_5"
+ PIN 11: "GPIO_6"
+ PIN 12: "GPIO_7"
+ PIN 13: "GPIO_8"
+ PIN 14: "GPIO_9"
+ PIN 15: "GPIO_10"
+ PIN 16: "GPIO_11"
+ PIN 17: "GPIO_12"
+ PIN 18: "GPIO_13"
+ PIN 19: "GPIO_14"
+ PIN 20: "GPIO_15"
+ PIN 21: "PWM0"
+ PIN 22: "PWM1"
+ PIN 23: "SPI0_CLK"
+ PIN 24: "SPI0_MOSI"
+ PIN 25: "SPI0_MISO"
+ PIN 26: "SPI0_CS"
+ PIN 27: "SPI0_HOLD"
+ PIN 28: "SPI0_WP"
+ PIN 29: "SPI1_CLK"
+ PIN 30: "SPI1_MOSI"
+ PIN 31: "SPI1_MISO"
+ PIN 32: "SPI1_CS"
+ PIN 33: "SPI2_CLK"
+ PIN 34: "SPI2_MOSI"
+ PIN 35: "SPI2_MISO"
+ PIN 36: "SPI2_CS"
+ PIN 37: "SPI2_HOLD"
+ PIN 38: "SPI2_WP"
+ PIN 39: "UART0_RXD"
+ PIN 40: "UART0_TXD"
+ PIN 41: "PCIE_PERESET_N"
+ PIN 42: "UART1_RXD"
+ PIN 43: "UART1_TXD"
+ PIN 44: "UART1_CTS"
+ PIN 45: "UART1_RTS"
+ PIN 46: "UART2_RXD"
+ PIN 47: "UART2_TXD"
+ PIN 48: "UART2_CTS"
+ PIN 49: "UART2_RTS"
+ PIN 50: "EMMC_DATA_0"
+ PIN 51: "EMMC_DATA_1"
+ PIN 52: "EMMC_DATA_2"
+ PIN 53: "EMMC_DATA_3"
+ PIN 54: "EMMC_DATA_4"
+ PIN 55: "EMMC_DATA_5"
+ PIN 56: "EMMC_DATA_6"
+ PIN 57: "EMMC_DATA_7"
+ PIN 58: "EMMC_CMD"
+ PIN 59: "EMMC_CK"
+ PIN 60: "EMMC_DSL"
+ PIN 61: "EMMC_RSTB"
+ PIN 62: "PCM_DTX"
+ PIN 63: "PCM_DRX"
+ PIN 64: "PCM_CLK"
+ PIN 65: "PCM_FS"
+ PIN 66: "MT7531_INT"
+ PIN 67: "SMI_MDC"
+ PIN 68: "SMI_MDIO"
+ PIN 69: "WF0_DIG_RESETB"
+ PIN 70: "WF0_CBA_RESETB"
+ PIN 71: "WF0_XO_REQ"
+ PIN 72: "WF0_TOP_CLK"
+ PIN 73: "WF0_TOP_DATA"
+ PIN 74: "WF0_HB1"
+ PIN 75: "WF0_HB2"
+ PIN 76: "WF0_HB3"
+ PIN 77: "WF0_HB4"
+ PIN 78: "WF0_HB0"
+ PIN 79: "WF0_HB0_B"
+ PIN 80: "WF0_HB5"
+ PIN 81: "WF0_HB6"
+ PIN 82: "WF0_HB7"
+ PIN 83: "WF0_HB8"
+ PIN 84: "WF0_HB9"
+ PIN 85: "WF0_HB10"
+ PIN 86: "WF1_DIG_RESETB"
+ PIN 87: "WF1_CBA_RESETB"
+ PIN 88: "WF1_XO_REQ"
+ PIN 89: "WF1_TOP_CLK"
+ PIN 90: "WF1_TOP_DATA"
+ PIN 91: "WF1_HB1"
+ PIN 92: "WF1_HB2"
+ PIN 93: "WF1_HB3"
+ PIN 94: "WF1_HB4"
+ PIN 95: "WF1_HB0"
+ PIN 96: "WF1_HB0_B"
+ PIN 97: "WF1_HB5"
+ PIN 98: "WF1_HB6"
+ PIN 99: "WF1_HB7"
+ PIN 100: "WF1_HB8"
+
+Valid values for function are:
+ "audio, "emmc", "eth", "i2c", "wifi", "led", "flash", "pcie",
+ "pwm", "spi", "uart", "watchdog"
+
+There is no "audio", "pcie" functions on mt7986b, you can only use those
+functions on mt7986a.
+
+Valid values for groups are:
+additional data is put followingly with valid value allowing us to know which
+applicable function and which relevant pins (in pin#) are able applied for that
+group.
+
+There is no "pcie_pereset", "uart1", "uart2" "emmc_51", "pcm", and "i2s" groups
+on mt7986b, you can only use those groups on mt7986a.
+
+ Valid value function pins (in pin#)
+ -------------------------------------------------------------------------
+ "watchdog" "watchdog" 0
+ "wifi_led" "led" 1, 2
+ "i2c" "i2c" 3, 4
+ "uart1_0" "uart" 7, 8, 9, 10
+ "pcie_clk" "pcie" 9
+ "pcie_wake" "pcie" 10
+ "spi1_0" "spi" 11, 12, 13, 14
+ "pwm1_1" "pwm" 20,
+ "pwm0" "pwm" 21,
+ "pwm1_0" "pwm" 22,
+ "snfi" "flash" 23, 24, 25, 26, 27, 28
+ "spi1_2" "spi" 29, 30, 31, 32
+ "emmc_45" "emmc" 22, 23, 24, 25, 26, 27,
+ 28, 29, 30, 31, 32
+ "spi1_1" "spi" 23, 24, 25, 26
+ "uart1_2" "uart" 29, 30, 31, 32
+ "uart1_1" "uart" 23, 24, 25, 26
+ "uart2_0" "uart" 29, 30, 31, 32
+ "spi0" "spi" 33, 34, 35, 36
+ "spi0_wp_hold" "spi" 37, 38
+ "uart1_3_rx_tx" "uart" 35, 36
+ "uart1_3_cts_rts" "uart" 37, 38
+ "uart2_1" "uart" 33, 34, 35, 36
+ "spi1_3" "spi" 33, 34, 35, 36
+ "uart0" "uart" 39, 40
+ "pcie_pereset" "pcie" 41
+ "uart1" "uart" 42, 43, 44, 45
+ "uart2" "uart" 46, 47, 48, 49
+ "emmc_51" "emmc" 50, 51, 52, 53, 54, 55,
+ 56, 57, 57, 59, 60, 61
+ "pcm" "audio" 62, 63, 64, 65
+ "i2s" "audio" 62, 63, 64, 65
+ "switch_int" "eth" 66
+ "mdc_mdio" "eth" 67
+
+Example:
+
+{
+ pio: pinctrl@1001f000 {
+ compatible = "mediatek,mt7986a-pinctrl";
+ reg = <0 0x1001f000 0 0x1000>,
+ <0 0x11c30000 0 0x1000>,
+ <0 0x11c40000 0 0x1000>,
+ <0 0x11e20000 0 0x1000>,
+ <0 0x11e30000 0 0x1000>,
+ <0 0x11f00000 0 0x1000>,
+ <0 0x11f10000 0 0x1000>,
+ <0 0x1000b000 0 0x1000>;
+ reg-names = "gpio_base", "iocfg_rt_base", "iocfg_rb_base",
+ "iocfg_lt_base", "iocfg_lb_base", "iocfg_tr_base",
+ "iocfg_tl_base", "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 100>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ #interrupt-cells = <2>;
+
+ uart1_pins: uart1-pins-42-to-45 {
+ mux {
+ function = "uart";
+ groups = "uart1";
+ };
+ };
+
+ uart2_pins: uart1-pins-46-to-49 {
+ mux {
+ function = "uart";
+ groups = "uart2";
+ };
+ };
+ ...
+ };
+}
--
2.29.2
Add basic chip support for Mediatek mt7986a, include
uart nodes with correct clocks, rng node with correct clock,
and watchdog node and mt7986a pinctrl node.
Add cpu node, timer node, gic node, psci and reserved-memory node
for ARM Trusted Firmware,
Add clock controller nodes, include 40M clock source, topckgen, infracfg,
apmixedsys and ethernet subsystem.
Signed-off-by: Sam Shih <[email protected]>
---
v2: modified clock and uart node due to clock driver updated
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 49 ++++
arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 227 +++++++++++++++++++
3 files changed, 277 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 4f68ebed2e31..e6c3a73b9e4a 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
new file mode 100644
index 000000000000..a58347c09ab2
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+/dts-v1/;
+#include "mt7986a.dtsi"
+
+/ {
+ model = "MediaTek MT7986a RFB";
+ compatible = "mediatek,mt7986a-rfb";
+ chosen {
+ bootargs = "console=ttyS0,115200n1 loglevel=8 \
+ earlycon=uart8250,mmio32,0x11002000";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+};
+
+&pio {
+ uart1_pins: uart1-pins-42-to-45 {
+ mux {
+ function = "uart";
+ groups = "uart1";
+ };
+ };
+
+ uart2_pins: uart1-pins-46-to-49 {
+ mux {
+ function = "uart";
+ groups = "uart2";
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
new file mode 100644
index 000000000000..dfe3e7101031
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -0,0 +1,227 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/mt7986-clk.h>
+
+/ {
+ compatible = "mediatek,mt7986a";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clk40m: oscillator@0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <40000000>;
+ clock-output-names = "clkxtal";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x2>;
+ #cooling-cells = <2>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ enable-method = "psci";
+ compatible = "arm,cortex-a53";
+ reg = <0x3>;
+ #cooling-cells = <2>;
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ /* 192 KiB reserved for ARM Trusted Firmware (BL31) */
+ secmon_reserved: secmon@43000000 {
+ reg = <0 0x43000000 0 0x30000>;
+ no-map;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ clock-frequency = <13000000>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ gic: interrupt-controller@c000000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x0c000000 0 0x40000>,
+ <0 0x0c080000 0 0x200000>;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ infracfg: infracfg@10001000 {
+ compatible = "mediatek,mt7986-infracfg", "syscon";
+ reg = <0 0x10001000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ topckgen: topckgen@1001b000 {
+ compatible = "mediatek,mt7986-topckgen", "syscon";
+ reg = <0 0x1001B000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ watchdog: watchdog@1001c000 {
+ compatible = "mediatek,mt7986-wdt",
+ "mediatek,mt6589-wdt";
+ reg = <0 0x1001c000 0 0x1000>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ #reset-cells = <1>;
+ status = "disabled";
+ };
+
+ apmixedsys: apmixedsys@1001e000 {
+ compatible = "mediatek,mt7986-apmixedsys";
+ reg = <0 0x1001E000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ pio: pinctrl@1001f000 {
+ compatible = "mediatek,mt7986a-pinctrl";
+ reg = <0 0x1001f000 0 0x1000>,
+ <0 0x11c30000 0 0x1000>,
+ <0 0x11c40000 0 0x1000>,
+ <0 0x11e20000 0 0x1000>,
+ <0 0x11e30000 0 0x1000>,
+ <0 0x11f00000 0 0x1000>,
+ <0 0x11f10000 0 0x1000>,
+ <0 0x1000b000 0 0x1000>;
+ reg-names = "gpio_base", "iocfg_rt_base", "iocfg_rb_base",
+ "iocfg_lt_base", "iocfg_lb_base", "iocfg_tr_base",
+ "iocfg_tl_base", "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 100>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ #interrupt-cells = <2>;
+ };
+
+ sgmiisys0: syscon@10060000 {
+ compatible = "mediatek,mt7986-sgmiisys_0",
+ "syscon";
+ reg = <0 0x10060000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ sgmiisys1: syscon@10070000 {
+ compatible = "mediatek,mt7986-sgmiisys_1",
+ "syscon";
+ reg = <0 0x10070000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ trng: trng@1020f000 {
+ compatible = "mediatek,mt7986-rng",
+ "mediatek,mt7623-rng";
+ reg = <0 0x1020f000 0 0x100>;
+ clocks = <&infracfg CLK_INFRA_TRNG_CK>;
+ clock-names = "rng";
+ status = "disabled";
+ };
+
+ uart0: serial@11002000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11002000 0 0x400>;
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART0_SEL>,
+ <&infracfg CLK_INFRA_UART0_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&topckgen CLK_TOP_UART_SEL>,
+ <&infracfg CLK_INFRA_UART0_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_XTAL>,
+ <&topckgen CLK_TOP_UART_SEL>;
+ status = "disabled";
+ };
+
+ uart1: serial@11003000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11003000 0 0x400>;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART1_SEL>,
+ <&infracfg CLK_INFRA_UART1_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&infracfg CLK_INFRA_UART1_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+ status = "disabled";
+ };
+
+ uart2: serial@11004000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11004000 0 0x400>;
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART2_SEL>,
+ <&infracfg CLK_INFRA_UART2_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&infracfg CLK_INFRA_UART2_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+ status = "disabled";
+ };
+
+ ethsys: syscon@15000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mediatek,mt7986-ethsys",
+ "syscon";
+ reg = <0 0x15000000 0 0x1000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ };
+
+};
--
2.29.2
Add basic chip support for Mediatek mt7986b, include
uart nodes with correct clocks, rng node with correct clock,
and watchdog node and mt7986b pinctrl node.
Add cpu node, timer node, gic node, psci and reserved-memory node
for ARM Trusted Firmware,
Add clock controller nodes, include 40M clock source, topckgen, infracfg,
apmixedsys and ethernet subsystem.
Signed-off-by: Sam Shih <[email protected]>
---
v2: modified clock and uart node due to clock driver updated
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts | 21 ++
arch/arm64/boot/dts/mediatek/mt7986b.dtsi | 227 +++++++++++++++++++
3 files changed, 249 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986b.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index e6c3a73b9e4a..d555e43d1ccc 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
new file mode 100644
index 000000000000..8296f1d27e77
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+/dts-v1/;
+#include "mt7986b.dtsi"
+
+/ {
+ model = "MediaTek MT7986b RFB";
+ compatible = "mediatek,mt7986b-rfb";
+ chosen {
+ bootargs = "console=ttyS0,115200n1 loglevel=8 \
+ earlycon=uart8250,mmio32,0x11002000";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b.dtsi b/arch/arm64/boot/dts/mediatek/mt7986b.dtsi
new file mode 100644
index 000000000000..1fd98fb7ba84
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986b.dtsi
@@ -0,0 +1,227 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/mt7986-clk.h>
+
+/ {
+ compatible = "mediatek,mt7986b";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clk40m: oscillator@0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <40000000>;
+ clock-output-names = "clkxtal";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x2>;
+ #cooling-cells = <2>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ enable-method = "psci";
+ compatible = "arm,cortex-a53";
+ reg = <0x3>;
+ #cooling-cells = <2>;
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ /* 192 KiB reserved for ARM Trusted Firmware (BL31) */
+ secmon_reserved: secmon@43000000 {
+ reg = <0 0x43000000 0 0x30000>;
+ no-map;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ clock-frequency = <13000000>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ gic: interrupt-controller@c000000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x0c000000 0 0x40000>,
+ <0 0x0c080000 0 0x200000>;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ infracfg: infracfg@10001000 {
+ compatible = "mediatek,mt7986-infracfg", "syscon";
+ reg = <0 0x10001000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ topckgen: topckgen@1001b000 {
+ compatible = "mediatek,mt7986-topckgen", "syscon";
+ reg = <0 0x1001B000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ watchdog: watchdog@1001c000 {
+ compatible = "mediatek,mt7986-wdt",
+ "mediatek,mt6589-wdt";
+ reg = <0 0x1001c000 0 0x1000>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ #reset-cells = <1>;
+ status = "disabled";
+ };
+
+ apmixedsys: apmixedsys@1001e000 {
+ compatible = "mediatek,mt7986-apmixedsys";
+ reg = <0 0x1001E000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ pio: pinctrl@1001f000 {
+ compatible = "mediatek,mt7986b-pinctrl";
+ reg = <0 0x1001f000 0 0x1000>,
+ <0 0x11c30000 0 0x1000>,
+ <0 0x11c40000 0 0x1000>,
+ <0 0x11e20000 0 0x1000>,
+ <0 0x11e30000 0 0x1000>,
+ <0 0x11f00000 0 0x1000>,
+ <0 0x11f10000 0 0x1000>,
+ <0 0x1000b000 0 0x1000>;
+ reg-names = "gpio_base", "iocfg_rt_base", "iocfg_rb_base",
+ "iocfg_lt_base", "iocfg_lb_base", "iocfg_tr_base",
+ "iocfg_tl_base", "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 41>, <&pio 66 66 35>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ #interrupt-cells = <2>;
+ };
+
+ sgmiisys0: syscon@10060000 {
+ compatible = "mediatek,mt7986-sgmiisys_0",
+ "syscon";
+ reg = <0 0x10060000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ sgmiisys1: syscon@10070000 {
+ compatible = "mediatek,mt7986-sgmiisys_1",
+ "syscon";
+ reg = <0 0x10070000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ trng: trng@1020f000 {
+ compatible = "mediatek,mt7986-rng",
+ "mediatek,mt7623-rng";
+ reg = <0 0x1020f000 0 0x100>;
+ clocks = <&infracfg CLK_INFRA_TRNG_CK>;
+ clock-names = "rng";
+ status = "disabled";
+ };
+
+ uart0: serial@11002000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11002000 0 0x400>;
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART0_SEL>,
+ <&infracfg CLK_INFRA_UART0_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&topckgen CLK_TOP_UART_SEL>,
+ <&infracfg CLK_INFRA_UART0_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_XTAL>,
+ <&topckgen CLK_TOP_UART_SEL>;
+ status = "disabled";
+ };
+
+ uart1: serial@11003000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11003000 0 0x400>;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART1_SEL>,
+ <&infracfg CLK_INFRA_UART1_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&infracfg CLK_INFRA_UART1_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+ status = "disabled";
+ };
+
+ uart2: serial@11004000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11004000 0 0x400>;
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART2_SEL>,
+ <&infracfg CLK_INFRA_UART2_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&infracfg CLK_INFRA_UART2_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+ status = "disabled";
+ };
+
+ ethsys: syscon@15000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mediatek,mt7986-ethsys",
+ "syscon";
+ reg = <0 0x15000000 0 0x1000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ };
+
+};
--
2.29.2
On 14/09/2021 10:51, Sam Shih wrote:
> Add basic chip support for Mediatek mt7986a, include
> uart nodes with correct clocks, rng node with correct clock,
> and watchdog node and mt7986a pinctrl node.
>
> Add cpu node, timer node, gic node, psci and reserved-memory node
> for ARM Trusted Firmware,
>
> Add clock controller nodes, include 40M clock source, topckgen, infracfg,
> apmixedsys and ethernet subsystem.
>
> Signed-off-by: Sam Shih <[email protected]>
>
> ---
> v2: modified clock and uart node due to clock driver updated
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 49 ++++
> arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 227 +++++++++++++++++++
> 3 files changed, 277 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a.dtsi
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 4f68ebed2e31..e6c3a73b9e4a 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> new file mode 100644
> index 000000000000..a58347c09ab2
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> @@ -0,0 +1,49 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Author: Sam.Shih <[email protected]>
> + */
> +
> +/dts-v1/;
> +#include "mt7986a.dtsi"
> +
> +/ {
> + model = "MediaTek MT7986a RFB";
> + compatible = "mediatek,mt7986a-rfb";
> + chosen {
> + bootargs = "console=ttyS0,115200n1 loglevel=8 \
> + earlycon=uart8250,mmio32,0x11002000";
We should be able to achieve this by using the stdout-path instead.
Regards,
Matthias
On 14/09/2021 10:51, Sam Shih wrote:
> This updates bindings for MT7986 pinctrl driver. The
> difference of pinctrl between mt7986a and mt7986b is that pin-41 to pin-65
> do not exist on mt7986b
>
> Signed-off-by: Sam Shih <[email protected]>
>
> ---
> v3 : make mt7986 pinctrl bindings as a separate file
> v2 : deleted the redundant description of mt7986a/mt7986b
> ---
> .../pinctrl/mediatek,mt7986-pinctrl.txt | 300 ++++++++++++++++++
> 1 file changed, 300 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.txt
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.txt
Normally new bindings should be using the yaml description instead of txt.
Regards,
Matthias
On Tue, Sep 14, 2021 at 10:52 AM Sam Shih <[email protected]> wrote:
> Certain SoC are missing the middle part gpios in consecutive pins,
> it's better to check if mtk_pin_desc is a valid pin for the extensibility
>
> Signed-off-by: Sam Shih <[email protected]>
> Acked-by: Sean Wang <[email protected]>
This patch applied for v5.16 so we get some stuff merged.
Yours,
Linus Walleij
Add basic chip support for Mediatek mt7986a, include
uart nodes with correct clocks, rng node with correct clock,
and watchdog node and mt7986a pinctrl node.
Add cpu node, timer node, gic node, psci and reserved-memory node
for ARM Trusted Firmware,
Add clock controller nodes, include 40M clock source, topckgen, infracfg,
apmixedsys and ethernet subsystem.
Signed-off-by: Sam Shih <[email protected]>
---
v3: used the stdout-path instead of console=ttyS0
v2: modified clock and uart node due to clock driver updated
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 54 +++++
arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 227 +++++++++++++++++++
3 files changed, 282 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 4f68ebed2e31..e6c3a73b9e4a 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
new file mode 100644
index 000000000000..e210d03ba70a
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+/dts-v1/;
+#include "mt7986a.dtsi"
+
+/ {
+ model = "MediaTek MT7986a RFB";
+ compatible = "mediatek,mt7986a-rfb";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs = "earlycon=uart8250,mmio32,0x11002000 swiotlb=512";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+};
+
+&pio {
+ uart1_pins: uart1-pins-42-to-45 {
+ mux {
+ function = "uart";
+ groups = "uart1";
+ };
+ };
+
+ uart2_pins: uart1-pins-46-to-49 {
+ mux {
+ function = "uart";
+ groups = "uart2";
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
new file mode 100644
index 000000000000..dfe3e7101031
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -0,0 +1,227 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/mt7986-clk.h>
+
+/ {
+ compatible = "mediatek,mt7986a";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clk40m: oscillator@0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <40000000>;
+ clock-output-names = "clkxtal";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x2>;
+ #cooling-cells = <2>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ enable-method = "psci";
+ compatible = "arm,cortex-a53";
+ reg = <0x3>;
+ #cooling-cells = <2>;
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ /* 192 KiB reserved for ARM Trusted Firmware (BL31) */
+ secmon_reserved: secmon@43000000 {
+ reg = <0 0x43000000 0 0x30000>;
+ no-map;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ clock-frequency = <13000000>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ gic: interrupt-controller@c000000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x0c000000 0 0x40000>,
+ <0 0x0c080000 0 0x200000>;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ infracfg: infracfg@10001000 {
+ compatible = "mediatek,mt7986-infracfg", "syscon";
+ reg = <0 0x10001000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ topckgen: topckgen@1001b000 {
+ compatible = "mediatek,mt7986-topckgen", "syscon";
+ reg = <0 0x1001B000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ watchdog: watchdog@1001c000 {
+ compatible = "mediatek,mt7986-wdt",
+ "mediatek,mt6589-wdt";
+ reg = <0 0x1001c000 0 0x1000>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ #reset-cells = <1>;
+ status = "disabled";
+ };
+
+ apmixedsys: apmixedsys@1001e000 {
+ compatible = "mediatek,mt7986-apmixedsys";
+ reg = <0 0x1001E000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ pio: pinctrl@1001f000 {
+ compatible = "mediatek,mt7986a-pinctrl";
+ reg = <0 0x1001f000 0 0x1000>,
+ <0 0x11c30000 0 0x1000>,
+ <0 0x11c40000 0 0x1000>,
+ <0 0x11e20000 0 0x1000>,
+ <0 0x11e30000 0 0x1000>,
+ <0 0x11f00000 0 0x1000>,
+ <0 0x11f10000 0 0x1000>,
+ <0 0x1000b000 0 0x1000>;
+ reg-names = "gpio_base", "iocfg_rt_base", "iocfg_rb_base",
+ "iocfg_lt_base", "iocfg_lb_base", "iocfg_tr_base",
+ "iocfg_tl_base", "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 100>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ #interrupt-cells = <2>;
+ };
+
+ sgmiisys0: syscon@10060000 {
+ compatible = "mediatek,mt7986-sgmiisys_0",
+ "syscon";
+ reg = <0 0x10060000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ sgmiisys1: syscon@10070000 {
+ compatible = "mediatek,mt7986-sgmiisys_1",
+ "syscon";
+ reg = <0 0x10070000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ trng: trng@1020f000 {
+ compatible = "mediatek,mt7986-rng",
+ "mediatek,mt7623-rng";
+ reg = <0 0x1020f000 0 0x100>;
+ clocks = <&infracfg CLK_INFRA_TRNG_CK>;
+ clock-names = "rng";
+ status = "disabled";
+ };
+
+ uart0: serial@11002000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11002000 0 0x400>;
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART0_SEL>,
+ <&infracfg CLK_INFRA_UART0_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&topckgen CLK_TOP_UART_SEL>,
+ <&infracfg CLK_INFRA_UART0_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_XTAL>,
+ <&topckgen CLK_TOP_UART_SEL>;
+ status = "disabled";
+ };
+
+ uart1: serial@11003000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11003000 0 0x400>;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART1_SEL>,
+ <&infracfg CLK_INFRA_UART1_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&infracfg CLK_INFRA_UART1_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+ status = "disabled";
+ };
+
+ uart2: serial@11004000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11004000 0 0x400>;
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART2_SEL>,
+ <&infracfg CLK_INFRA_UART2_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&infracfg CLK_INFRA_UART2_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+ status = "disabled";
+ };
+
+ ethsys: syscon@15000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mediatek,mt7986-ethsys",
+ "syscon";
+ reg = <0 0x15000000 0 0x1000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ };
+
+};
--
2.29.2
Add basic chip support for Mediatek mt7986b, include
uart nodes with correct clocks, rng node with correct clock,
and watchdog node and mt7986b pinctrl node.
Add cpu node, timer node, gic node, psci and reserved-memory node
for ARM Trusted Firmware,
Add clock controller nodes, include 40M clock source, topckgen, infracfg,
apmixedsys and ethernet subsystem.
Signed-off-by: Sam Shih <[email protected]>
---
v3: used the stdout-path instead of console=ttyS0
v2: modified clock and uart node due to clock driver updated
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts | 26 +++
arch/arm64/boot/dts/mediatek/mt7986b.dtsi | 227 +++++++++++++++++++
3 files changed, 254 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986b.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index e6c3a73b9e4a..d555e43d1ccc 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
new file mode 100644
index 000000000000..95a202505bb2
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+/dts-v1/;
+#include "mt7986b.dtsi"
+
+/ {
+ model = "MediaTek MT7986b RFB";
+ compatible = "mediatek,mt7986b-rfb";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs = "earlycon=uart8250,mmio32,0x11002000 swiotlb=512";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b.dtsi b/arch/arm64/boot/dts/mediatek/mt7986b.dtsi
new file mode 100644
index 000000000000..1fd98fb7ba84
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986b.dtsi
@@ -0,0 +1,227 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/mt7986-clk.h>
+
+/ {
+ compatible = "mediatek,mt7986b";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clk40m: oscillator@0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <40000000>;
+ clock-output-names = "clkxtal";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x2>;
+ #cooling-cells = <2>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ enable-method = "psci";
+ compatible = "arm,cortex-a53";
+ reg = <0x3>;
+ #cooling-cells = <2>;
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ /* 192 KiB reserved for ARM Trusted Firmware (BL31) */
+ secmon_reserved: secmon@43000000 {
+ reg = <0 0x43000000 0 0x30000>;
+ no-map;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ clock-frequency = <13000000>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ gic: interrupt-controller@c000000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x0c000000 0 0x40000>,
+ <0 0x0c080000 0 0x200000>;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ infracfg: infracfg@10001000 {
+ compatible = "mediatek,mt7986-infracfg", "syscon";
+ reg = <0 0x10001000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ topckgen: topckgen@1001b000 {
+ compatible = "mediatek,mt7986-topckgen", "syscon";
+ reg = <0 0x1001B000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ watchdog: watchdog@1001c000 {
+ compatible = "mediatek,mt7986-wdt",
+ "mediatek,mt6589-wdt";
+ reg = <0 0x1001c000 0 0x1000>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ #reset-cells = <1>;
+ status = "disabled";
+ };
+
+ apmixedsys: apmixedsys@1001e000 {
+ compatible = "mediatek,mt7986-apmixedsys";
+ reg = <0 0x1001E000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ pio: pinctrl@1001f000 {
+ compatible = "mediatek,mt7986b-pinctrl";
+ reg = <0 0x1001f000 0 0x1000>,
+ <0 0x11c30000 0 0x1000>,
+ <0 0x11c40000 0 0x1000>,
+ <0 0x11e20000 0 0x1000>,
+ <0 0x11e30000 0 0x1000>,
+ <0 0x11f00000 0 0x1000>,
+ <0 0x11f10000 0 0x1000>,
+ <0 0x1000b000 0 0x1000>;
+ reg-names = "gpio_base", "iocfg_rt_base", "iocfg_rb_base",
+ "iocfg_lt_base", "iocfg_lb_base", "iocfg_tr_base",
+ "iocfg_tl_base", "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 41>, <&pio 66 66 35>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ #interrupt-cells = <2>;
+ };
+
+ sgmiisys0: syscon@10060000 {
+ compatible = "mediatek,mt7986-sgmiisys_0",
+ "syscon";
+ reg = <0 0x10060000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ sgmiisys1: syscon@10070000 {
+ compatible = "mediatek,mt7986-sgmiisys_1",
+ "syscon";
+ reg = <0 0x10070000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ trng: trng@1020f000 {
+ compatible = "mediatek,mt7986-rng",
+ "mediatek,mt7623-rng";
+ reg = <0 0x1020f000 0 0x100>;
+ clocks = <&infracfg CLK_INFRA_TRNG_CK>;
+ clock-names = "rng";
+ status = "disabled";
+ };
+
+ uart0: serial@11002000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11002000 0 0x400>;
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART0_SEL>,
+ <&infracfg CLK_INFRA_UART0_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&topckgen CLK_TOP_UART_SEL>,
+ <&infracfg CLK_INFRA_UART0_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_XTAL>,
+ <&topckgen CLK_TOP_UART_SEL>;
+ status = "disabled";
+ };
+
+ uart1: serial@11003000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11003000 0 0x400>;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART1_SEL>,
+ <&infracfg CLK_INFRA_UART1_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&infracfg CLK_INFRA_UART1_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+ status = "disabled";
+ };
+
+ uart2: serial@11004000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11004000 0 0x400>;
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART2_SEL>,
+ <&infracfg CLK_INFRA_UART2_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&infracfg CLK_INFRA_UART2_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+ status = "disabled";
+ };
+
+ ethsys: syscon@15000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mediatek,mt7986-ethsys",
+ "syscon";
+ reg = <0 0x15000000 0 0x1000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ };
+
+};
--
2.29.2
This updates bindings for MT7986 pinctrl driver. The
difference of pinctrl between mt7986a and mt7986b is that pin-41 to pin-65
do not exist on mt7986b
Signed-off-by: Sam Shih <[email protected]>
---
v4 : used yaml format instead of txt format document
v3 : make mt7986 pinctrl bindings as a separate file
v2 : deleted the redundant description of mt7986a/mt7986b
---
.../pinctrl/mediatek,mt7986-pinctrl.yaml | 350 ++++++++++++++++++
1 file changed, 350 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
new file mode 100644
index 000000000000..e59aada817af
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
@@ -0,0 +1,350 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/mediatek,mt7986-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek MT7986 Pin Controller Device Tree Bindings
+
+maintainers:
+ - Sean Wang <[email protected]>
+
+description: |+
+ The MediaTek's MT7986 Pin controller is used to control SoC pins.
+
+properties:
+ compatible:
+ enum:
+ - mediatek,mt7986a-pinctrl
+ - mediatek,mt7986b-pinctrl
+
+ reg:
+ minItems: 8
+ maxItems: 8
+
+ reg-names:
+ items:
+ - const: gpio_base
+ - const: iocfg_rt_base
+ - const: iocfg_rb_base
+ - const: iocfg_lt_base
+ - const: iocfg_lb_base
+ - const: iocfg_tr_base
+ - const: iocfg_tl_base
+ - const: eint
+
+ gpio-controller: true
+
+ "#gpio-cells":
+ const: 2
+ description: |
+ Number of cells in GPIO specifier. Since the generic GPIO
+ binding is used, the amount of cells must be specified as 2. See the below
+ mentioned gpio binding representation for description of particular cells.
+
+ interrupt-controller: true
+
+ interrupts:
+ maxItems: 1
+
+ "#interrupt-cells":
+ const: 2
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - gpio-controller
+ - "#gpio-cells"
+
+patternProperties:
+ '-[0-9]+$':
+ type: object
+ additionalProperties: false
+
+ patternProperties:
+ 'mux':
+ type: object
+ additionalProperties: false
+ description: |
+ pinmux configuration nodes.
+ $ref: "/schemas/pinctrl/pinmux-node.yaml"
+ properties:
+ function:
+ description: |
+ A string containing the name of the function to mux to the group.
+ There is no "audio", "pcie" functions on mt7986b, you can only use
+ those functions on mt7986a.
+ enum: [audio, emmc, eth, i2c, led, flash, pcie, pwm, spi, uart,
+ watchdog, wifi]
+ groups:
+ description: |
+ An array of strings. Each string contains the name of a group.
+ There is no "pcie_pereset", "uart1", "uart2" "emmc_51", "pcm",
+ and "i2s" groups on mt7986b, you can only use those groups on
+ mt7986a.
+ required:
+ - function
+ - groups
+
+ allOf:
+ - if:
+ properties:
+ function:
+ const: audio
+ then:
+ properties:
+ groups:
+ enum: [pcm, i2s]
+ - if:
+ properties:
+ function:
+ const: emmc
+ then:
+ properties:
+ groups:
+ enum: [emmc, emmc_rst]
+ - if:
+ properties:
+ function:
+ const: eth
+ then:
+ properties:
+ groups:
+ enum: [switch_int, mdc_mdio]
+ - if:
+ properties:
+ function:
+ const: i2c
+ then:
+ properties:
+ groups:
+ enum: [i2c]
+ - if:
+ properties:
+ function:
+ const: led
+ then:
+ properties:
+ groups:
+ enum: [wifi_led]
+ - if:
+ properties:
+ function:
+ const: flash
+ then:
+ properties:
+ groups:
+ enum: [snfi]
+ - if:
+ properties:
+ function:
+ const: pcie
+ then:
+ properties:
+ groups:
+ enum: [pcie_clk, pcie_wake, pcie_pereset]
+ - if:
+ properties:
+ function:
+ const: pwm
+ then:
+ properties:
+ groups:
+ enum: [pwm0, pwm1_0, pwm1_1]
+ - if:
+ properties:
+ function:
+ const: spi
+ then:
+ properties:
+ groups:
+ enum: [spi0, spi0_wp_hold, spi1_0, spi1_1, spi1_2, spi1_3]
+ - if:
+ properties:
+ function:
+ const: uart
+ then:
+ properties:
+ groups:
+ enum: [uart1_0, uart1_1, uart1_2, uart1_3_rx_tx,
+ uart1_3_cts_rts, uart2_0, uart2_1, uart0, uart1, uart2]
+ - if:
+ properties:
+ function:
+ const: watchdog
+ then:
+ properties:
+ groups:
+ enum: [watchdog]
+ - if:
+ properties:
+ function:
+ const: wifi
+ then:
+ properties:
+ groups:
+ enum: [wf_2g, wf_5g, wf_dbdc]
+ 'conf':
+ type: object
+ additionalProperties: false
+ description: |
+ pinconf configuration nodes.
+ $ref: "/schemas/pinctrl/pincfg-node.yaml"
+
+ properties:
+ pins:
+ description: |
+ An array of strings. Each string contains the name of a pin.
+ There is no PIN 41 to PIN 65 above on mt7686b, you can only use
+ those pins on mt7986a.
+ enum: [SYS_WATCHDOG, WF2G_LED, WF5G_LED, I2C_SCL, I2C_SDA, GPIO_0,
+ GPIO_1, GPIO_2, GPIO_3, GPIO_4, GPIO_5, GPIO_6, GPIO_7,
+ GPIO_8, GPIO_9, GPIO_10, GPIO_11, GPIO_12, GPIO_13, GPIO_14,
+ GPIO_15, PWM0, PWM1, SPI0_CLK, SPI0_MOSI, SPI0_MISO, SPI0_CS,
+ SPI0_HOLD, SPI0_WP, SPI1_CLK, SPI1_MOSI, SPI1_MISO, SPI1_CS,
+ SPI2_CLK, SPI2_MOSI, SPI2_MISO, SPI2_CS, SPI2_HOLD, SPI2_WP,
+ UART0_RXD, UART0_TXD, PCIE_PERESET_N, UART1_RXD, UART1_TXD,
+ UART1_CTS, UART1_RTS, UART2_RXD, UART2_TXD, UART2_CTS,
+ UART2_RTS, EMMC_DATA_0, EMMC_DATA_1, EMMC_DATA_2,
+ EMMC_DATA_3, EMMC_DATA_4, EMMC_DATA_5, EMMC_DATA_6,
+ EMMC_DATA_7, EMMC_CMD, EMMC_CK, EMMC_DSL, EMMC_RSTB, PCM_DTX,
+ PCM_DRX, PCM_CLK, PCM_FS, MT7531_INT, SMI_MDC, SMI_MDIO,
+ WF0_DIG_RESETB, WF0_CBA_RESETB, WF0_XO_REQ, WF0_TOP_CLK,
+ WF0_TOP_DATA, WF0_HB1, WF0_HB2, WF0_HB3, WF0_HB4, WF0_HB0,
+ WF0_HB0_B, WF0_HB5, WF0_HB6, WF0_HB7, WF0_HB8, WF0_HB9,
+ WF0_HB10, WF1_DIG_RESETB, WF1_CBA_RESETB, WF1_XO_REQ,
+ WF1_TOP_CLK, WF1_TOP_DATA, WF1_HB1, WF1_HB2, WF1_HB3,
+ WF1_HB4, WF1_HB0, WF1_HB0_B, WF1_HB5, WF1_HB6, WF1_HB7,
+ WF1_HB8]
+
+ bias-disable: true
+
+ bias-pull-up: true
+
+ bias-pull-down: true
+
+ input-enable: true
+
+ input-disable: true
+
+ output-enable: true
+
+ output-low: true
+
+ output-high: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ drive-strength:
+ enum: [2, 4, 6, 8, 10, 12, 14, 16]
+
+ mediatek,pull-up-adv:
+ description: |
+ Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
+ Pull up setings for 2 pull resistors, R0 and R1. Valid arguments
+ are described as below:
+ 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+ 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+ 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+ 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+
+ mediatek,pull-down-adv:
+ description: |
+ Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
+ Pull down setings for 2 pull resistors, R0 and R1. Valid arguments
+ are described as below:
+ 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+ 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+ 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+ 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+
+ required:
+ - pins
+
+additionalProperties: false
+
+pin_group_table:
+ - |
+ Valid values for groups are:
+
+ There is no "pcie_pereset", "uart1", "uart2" "emmc_51", "pcm", and "i2s"
+ groups on mt7986b, you can only use those groups on mt7986a.
+
+ Valid value function pins (in pin#)
+ -------------------------------------------------------------------------
+ "watchdog" "watchdog" 0
+ "wifi_led" "led" 1, 2
+ "i2c" "i2c" 3, 4
+ "uart1_0" "uart" 7, 8, 9, 10
+ "pcie_clk" "pcie" 9
+ "pcie_wake" "pcie" 10
+ "spi1_0" "spi" 11, 12, 13, 14
+ "pwm1_1" "pwm" 20,
+ "pwm0" "pwm" 21,
+ "pwm1_0" "pwm" 22,
+ "snfi" "flash" 23, 24, 25, 26, 27, 28
+ "spi1_2" "spi" 29, 30, 31, 32
+ "emmc_45" "emmc" 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32
+ "spi1_1" "spi" 23, 24, 25, 26
+ "uart1_2" "uart" 29, 30, 31, 32
+ "uart1_1" "uart" 23, 24, 25, 26
+ "uart2_0" "uart" 29, 30, 31, 32
+ "spi0" "spi" 33, 34, 35, 36
+ "spi0_wp_hold" "spi" 37, 38
+ "uart1_3_rx_tx" "uart" 35, 36
+ "uart1_3_cts_rts" "uart" 37, 38
+ "uart2_1" "uart" 33, 34, 35, 36
+ "spi1_3" "spi" 33, 34, 35, 36
+ "uart0" "uart" 39, 40
+ "pcie_pereset" "pcie" 41
+ "uart1" "uart" 42, 43, 44, 45
+ "uart2" "uart" 46, 47, 48, 49
+ "emmc_51" "emmc" 50, 51, 52, 53, 54, 55, 56, 57, 57, 59, 60, 61
+ "pcm" "audio" 62, 63, 64, 65
+ "i2s" "audio" 62, 63, 64, 65
+ "switch_int" "eth" 66
+ "mdc_mdio" "eth" 67
+
+examples:
+ - |
+ soc {
+ pio: pinctrl@1001f000 {
+ compatible = "mediatek,mt7986a-pinctrl";
+ reg = <0 0x1001f000 0 0x1000>,
+ <0 0x11c30000 0 0x1000>,
+ <0 0x11c40000 0 0x1000>,
+ <0 0x11e20000 0 0x1000>,
+ <0 0x11e30000 0 0x1000>,
+ <0 0x11f00000 0 0x1000>,
+ <0 0x11f10000 0 0x1000>,
+ <0 0x1000b000 0 0x1000>;
+ reg-names = "gpio_base", "iocfg_rt_base", "iocfg_rb_base",
+ "iocfg_lt_base", "iocfg_lb_base", "iocfg_tr_base",
+ "iocfg_tl_base", "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 100>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ #interrupt-cells = <2>;
+
+ uart1_pins: uart1-pins-42-to-45 {
+ mux {
+ function = "uart";
+ groups = "uart1";
+ };
+ };
+
+ uart2_pins: uart1-pins-46-to-49 {
+ mux {
+ function = "uart";
+ groups = "uart2";
+ };
+ };
+
+ };
+ };
--
2.29.2
On Fri, 24 Sep 2021 19:44:59 +0800, Sam Shih wrote:
> This updates bindings for MT7986 pinctrl driver. The
> difference of pinctrl between mt7986a and mt7986b is that pin-41 to pin-65
> do not exist on mt7986b
>
> Signed-off-by: Sam Shih <[email protected]>
>
> ---
> v4 : used yaml format instead of txt format document
> v3 : make mt7986 pinctrl bindings as a separate file
> v2 : deleted the redundant description of mt7986a/mt7986b
> ---
> .../pinctrl/mediatek,mt7986-pinctrl.yaml | 350 ++++++++++++++++++
> 1 file changed, 350 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml: 'pin_group_table' is not one of ['$id', '$schema', 'title', 'description', 'examples', 'required', 'allOf', 'anyOf', 'oneOf', 'definitions', '$defs', 'additionalProperties', 'dependencies', 'patternProperties', 'properties', 'if', 'then', 'else', 'unevaluatedProperties', 'deprecated', 'maintainers', 'select']
from schema $id: http://devicetree.org/meta-schemas/base.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml: patternProperties:-[0-9]+$:patternProperties:conf:properties:mediatek,pull-up-adv: 'oneOf' conditional failed, one must be fixed:
'type' is a required property
hint: A vendor boolean property can use "type: boolean"
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml: patternProperties:-[0-9]+$:patternProperties:conf:properties:mediatek,pull-up-adv: 'oneOf' conditional failed, one must be fixed:
'enum' is a required property
'const' is a required property
hint: A vendor string property with exact values has an implicit type
from schema $id: http://devicetree.org/meta-schemas/vendor-props.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml: patternProperties:-[0-9]+$:patternProperties:conf:properties:mediatek,pull-up-adv: 'oneOf' conditional failed, one must be fixed:
'$ref' is a required property
'allOf' is a required property
hint: A vendor property needs a $ref to types.yaml
from schema $id: http://devicetree.org/meta-schemas/vendor-props.yaml#
hint: Vendor specific properties must have a type and description unless they have a defined, common suffix.
from schema $id: http://devicetree.org/meta-schemas/vendor-props.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml: patternProperties:-[0-9]+$:patternProperties:conf:properties:mediatek,pull-down-adv: 'oneOf' conditional failed, one must be fixed:
'type' is a required property
hint: A vendor boolean property can use "type: boolean"
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml: patternProperties:-[0-9]+$:patternProperties:conf:properties:mediatek,pull-down-adv: 'oneOf' conditional failed, one must be fixed:
'enum' is a required property
'const' is a required property
hint: A vendor string property with exact values has an implicit type
from schema $id: http://devicetree.org/meta-schemas/vendor-props.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml: patternProperties:-[0-9]+$:patternProperties:conf:properties:mediatek,pull-down-adv: 'oneOf' conditional failed, one must be fixed:
'$ref' is a required property
'allOf' is a required property
hint: A vendor property needs a $ref to types.yaml
from schema $id: http://devicetree.org/meta-schemas/vendor-props.yaml#
hint: Vendor specific properties must have a type and description unless they have a defined, common suffix.
from schema $id: http://devicetree.org/meta-schemas/vendor-props.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml: ignoring, error in schema:
warning: no schema found in file: ./Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
Error: Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.example.dts:37.27-28 syntax error
FATAL ERROR: Unable to parse input tree
make[1]: *** [scripts/Makefile.lib:385: Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.example.dt.yaml] Error 1
make[1]: *** Waiting for unfinished jobs....
make: *** [Makefile:1441: dt_binding_check] Error 2
doc reference errors (make refcheckdocs):
See https://patchwork.ozlabs.org/patch/1532240
This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit.
This updates bindings for MT7986 pinctrl driver. The
difference of pinctrl between mt7986a and mt7986b is that pin-41 to pin-65
do not exist on mt7986b
Signed-off-by: Sam Shih <[email protected]>
---
v5 : fixed yamllint warnings/errors
v4 : used yaml format instead of txt format document
v3 : make mt7986 pinctrl bindings as a separate file
v2 : deleted the redundant description of mt7986a/mt7986b
---
.../pinctrl/mediatek,mt7986-pinctrl.yaml | 353 ++++++++++++++++++
1 file changed, 353 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
new file mode 100644
index 000000000000..51a13129bcb8
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
@@ -0,0 +1,353 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/mediatek,mt7986-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek MT7986 Pin Controller Device Tree Bindings
+
+maintainers:
+ - Sean Wang <[email protected]>
+
+description: |+
+ The MediaTek's MT7986 Pin controller is used to control SoC pins.
+
+properties:
+ compatible:
+ enum:
+ - mediatek,mt7986a-pinctrl
+ - mediatek,mt7986b-pinctrl
+
+ reg:
+ minItems: 8
+ maxItems: 8
+
+ reg-names:
+ items:
+ - const: gpio_base
+ - const: iocfg_rt_base
+ - const: iocfg_rb_base
+ - const: iocfg_lt_base
+ - const: iocfg_lb_base
+ - const: iocfg_tr_base
+ - const: iocfg_tl_base
+ - const: eint
+
+ gpio-controller: true
+
+ "#gpio-cells":
+ const: 2
+ description: |
+ Number of cells in GPIO specifier. Since the generic GPIO
+ binding is used, the amount of cells must be specified as 2. See the below
+ mentioned gpio binding representation for description of particular cells.
+
+ interrupt-controller: true
+
+ interrupts:
+ maxItems: 1
+
+ "#interrupt-cells":
+ const: 2
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - gpio-controller
+ - "#gpio-cells"
+
+patternProperties:
+ '-[0-9]+$':
+ type: object
+ additionalProperties: false
+
+ patternProperties:
+ 'mux':
+ type: object
+ additionalProperties: false
+ description: |
+ pinmux configuration nodes.
+
+ Valid value function pins (in pin#)
+ ---------------------------------------------------------------------
+ "watchdog" "watchdog" 0
+ "wifi_led" "led" 1, 2
+ "i2c" "i2c" 3, 4
+ "uart1_0" "uart" 7, 8, 9, 10
+ "pcie_clk" "pcie" 9
+ "pcie_wake" "pcie" 10
+ "spi1_0" "spi" 11, 12, 13, 14
+ "pwm1_1" "pwm" 20,
+ "pwm0" "pwm" 21,
+ "pwm1_0" "pwm" 22,
+ "snfi" "flash" 23, 24, 25, 26, 27, 28
+ "spi1_2" "spi" 29, 30, 31, 32
+ "emmc_45" "emmc" 22, 23, 24, 25, 26, 27, 28, 29, 30,
+ 31, 32
+ "spi1_1" "spi" 23, 24, 25, 26
+ "uart1_2" "uart" 29, 30, 31, 32
+ "uart1_1" "uart" 23, 24, 25, 26
+ "uart2_0" "uart" 29, 30, 31, 32
+ "spi0" "spi" 33, 34, 35, 36
+ "spi0_wp_hold" "spi" 37, 38
+ "uart1_3_rx_tx" "uart" 35, 36
+ "uart1_3_cts_rts" "uart" 37, 38
+ "uart2_1" "uart" 33, 34, 35, 36
+ "spi1_3" "spi" 33, 34, 35, 36
+ "uart0" "uart" 39, 40
+ "pcie_pereset" "pcie" 41
+ "uart1" "uart" 42, 43, 44, 45
+ "uart2" "uart" 46, 47, 48, 49
+ "emmc_51" "emmc" 50, 51, 52, 53, 54, 55, 56, 57, 57,
+ 59, 60, 61
+ "pcm" "audio" 62, 63, 64, 65
+ "i2s" "audio" 62, 63, 64, 65
+ "switch_int" "eth" 66
+ "mdc_mdio" "eth" 67
+
+ $ref: "/schemas/pinctrl/pinmux-node.yaml"
+ properties:
+ function:
+ description: |
+ A string containing the name of the function to mux to the group.
+ There is no "audio", "pcie" functions on mt7986b, you can only use
+ those functions on mt7986a.
+ enum: [audio, emmc, eth, i2c, led, flash, pcie, pwm, spi, uart,
+ watchdog, wifi]
+ groups:
+ description: |
+ An array of strings. Each string contains the name of a group.
+ There is no "pcie_pereset", "uart1", "uart2" "emmc_51", "pcm",
+ and "i2s" groups on mt7986b, you can only use those groups on
+ mt7986a.
+ required:
+ - function
+ - groups
+
+ allOf:
+ - if:
+ properties:
+ function:
+ const: audio
+ then:
+ properties:
+ groups:
+ enum: [pcm, i2s]
+ - if:
+ properties:
+ function:
+ const: emmc
+ then:
+ properties:
+ groups:
+ enum: [emmc, emmc_rst]
+ - if:
+ properties:
+ function:
+ const: eth
+ then:
+ properties:
+ groups:
+ enum: [switch_int, mdc_mdio]
+ - if:
+ properties:
+ function:
+ const: i2c
+ then:
+ properties:
+ groups:
+ enum: [i2c]
+ - if:
+ properties:
+ function:
+ const: led
+ then:
+ properties:
+ groups:
+ enum: [wifi_led]
+ - if:
+ properties:
+ function:
+ const: flash
+ then:
+ properties:
+ groups:
+ enum: [snfi]
+ - if:
+ properties:
+ function:
+ const: pcie
+ then:
+ properties:
+ groups:
+ enum: [pcie_clk, pcie_wake, pcie_pereset]
+ - if:
+ properties:
+ function:
+ const: pwm
+ then:
+ properties:
+ groups:
+ enum: [pwm0, pwm1_0, pwm1_1]
+ - if:
+ properties:
+ function:
+ const: spi
+ then:
+ properties:
+ groups:
+ enum: [spi0, spi0_wp_hold, spi1_0, spi1_1, spi1_2, spi1_3]
+ - if:
+ properties:
+ function:
+ const: uart
+ then:
+ properties:
+ groups:
+ enum: [uart1_0, uart1_1, uart1_2, uart1_3_rx_tx,
+ uart1_3_cts_rts, uart2_0, uart2_1, uart0, uart1, uart2]
+ - if:
+ properties:
+ function:
+ const: watchdog
+ then:
+ properties:
+ groups:
+ enum: [watchdog]
+ - if:
+ properties:
+ function:
+ const: wifi
+ then:
+ properties:
+ groups:
+ enum: [wf_2g, wf_5g, wf_dbdc]
+ 'conf':
+ type: object
+ additionalProperties: false
+ description: |
+ pinconf configuration nodes.
+ $ref: "/schemas/pinctrl/pincfg-node.yaml"
+
+ properties:
+ pins:
+ description: |
+ An array of strings. Each string contains the name of a pin.
+ There is no PIN 41 to PIN 65 above on mt7686b, you can only use
+ those pins on mt7986a.
+ enum: [SYS_WATCHDOG, WF2G_LED, WF5G_LED, I2C_SCL, I2C_SDA, GPIO_0,
+ GPIO_1, GPIO_2, GPIO_3, GPIO_4, GPIO_5, GPIO_6, GPIO_7,
+ GPIO_8, GPIO_9, GPIO_10, GPIO_11, GPIO_12, GPIO_13, GPIO_14,
+ GPIO_15, PWM0, PWM1, SPI0_CLK, SPI0_MOSI, SPI0_MISO, SPI0_CS,
+ SPI0_HOLD, SPI0_WP, SPI1_CLK, SPI1_MOSI, SPI1_MISO, SPI1_CS,
+ SPI2_CLK, SPI2_MOSI, SPI2_MISO, SPI2_CS, SPI2_HOLD, SPI2_WP,
+ UART0_RXD, UART0_TXD, PCIE_PERESET_N, UART1_RXD, UART1_TXD,
+ UART1_CTS, UART1_RTS, UART2_RXD, UART2_TXD, UART2_CTS,
+ UART2_RTS, EMMC_DATA_0, EMMC_DATA_1, EMMC_DATA_2,
+ EMMC_DATA_3, EMMC_DATA_4, EMMC_DATA_5, EMMC_DATA_6,
+ EMMC_DATA_7, EMMC_CMD, EMMC_CK, EMMC_DSL, EMMC_RSTB, PCM_DTX,
+ PCM_DRX, PCM_CLK, PCM_FS, MT7531_INT, SMI_MDC, SMI_MDIO,
+ WF0_DIG_RESETB, WF0_CBA_RESETB, WF0_XO_REQ, WF0_TOP_CLK,
+ WF0_TOP_DATA, WF0_HB1, WF0_HB2, WF0_HB3, WF0_HB4, WF0_HB0,
+ WF0_HB0_B, WF0_HB5, WF0_HB6, WF0_HB7, WF0_HB8, WF0_HB9,
+ WF0_HB10, WF1_DIG_RESETB, WF1_CBA_RESETB, WF1_XO_REQ,
+ WF1_TOP_CLK, WF1_TOP_DATA, WF1_HB1, WF1_HB2, WF1_HB3,
+ WF1_HB4, WF1_HB0, WF1_HB0_B, WF1_HB5, WF1_HB6, WF1_HB7,
+ WF1_HB8]
+
+ bias-disable: true
+
+ bias-pull-up: true
+
+ bias-pull-down: true
+
+ input-enable: true
+
+ input-disable: true
+
+ output-enable: true
+
+ output-low: true
+
+ output-high: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ drive-strength:
+ enum: [2, 4, 6, 8, 10, 12, 14, 16]
+
+ mediatek,pull-up-adv:
+ description: |
+ Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
+ Pull up setings for 2 pull resistors, R0 and R1. Valid arguments
+ are described as below:
+ 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+ 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+ 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+ 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+
+ mediatek,pull-down-adv:
+ description: |
+ Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
+ Pull down setings for 2 pull resistors, R0 and R1. Valid arguments
+ are described as below:
+ 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+ 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+ 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+ 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+
+ required:
+ - pins
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ soc {
+ pio: pinctrl@1001f000 {
+ compatible = "mediatek,mt7986a-pinctrl";
+ reg = <0 0x1001f000 0 0x1000>,
+ <0 0x11c30000 0 0x1000>,
+ <0 0x11c40000 0 0x1000>,
+ <0 0x11e20000 0 0x1000>,
+ <0 0x11e30000 0 0x1000>,
+ <0 0x11f00000 0 0x1000>,
+ <0 0x11f10000 0 0x1000>,
+ <0 0x1000b000 0 0x1000>;
+ reg-names = "gpio_base", "iocfg_rt_base", "iocfg_rb_base",
+ "iocfg_lt_base", "iocfg_lb_base", "iocfg_tr_base",
+ "iocfg_tl_base", "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 100>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ #interrupt-cells = <2>;
+
+ uart1_pins: uart1-pins-42-to-45 {
+ mux {
+ function = "uart";
+ groups = "uart1";
+ };
+ };
+
+ uart2_pins: uart1-pins-46-to-49 {
+ mux {
+ function = "uart";
+ groups = "uart2";
+ };
+ };
+
+ };
+ };
--
2.29.2
On Mon, 27 Sep 2021 10:34:19 +0800, Sam Shih wrote:
> This updates bindings for MT7986 pinctrl driver. The
> difference of pinctrl between mt7986a and mt7986b is that pin-41 to pin-65
> do not exist on mt7986b
>
> Signed-off-by: Sam Shih <[email protected]>
>
> ---
> v5 : fixed yamllint warnings/errors
> v4 : used yaml format instead of txt format document
> v3 : make mt7986 pinctrl bindings as a separate file
> v2 : deleted the redundant description of mt7986a/mt7986b
> ---
> .../pinctrl/mediatek,mt7986-pinctrl.yaml | 353 ++++++++++++++++++
> 1 file changed, 353 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.example.dts:25.13-32.43: Warning (reg_format): /example-0/soc/pinctrl@1001f000:reg: property has invalid length (128 bytes) (#address-cells == 2, #size-cells == 1)
Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.example.dt.yaml: Warning (pci_device_reg): Failed prerequisite 'reg_format'
Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.example.dt.yaml: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.example.dt.yaml: Warning (simple_bus_reg): Failed prerequisite 'reg_format'
Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.example.dt.yaml: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.example.dt.yaml: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.example.dts:23.33-58.13: Warning (avoid_default_addr_size): /example-0/soc/pinctrl@1001f000: Relying on default #address-cells value
Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.example.dts:23.33-58.13: Warning (avoid_default_addr_size): /example-0/soc/pinctrl@1001f000: Relying on default #size-cells value
Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.example.dt.yaml: Warning (unique_unit_address): Failed prerequisite 'avoid_default_addr_size'
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.example.dt.yaml: pinctrl@1001f000: 'gpio-ranges' does not match any of the regexes: '-[0-9]+$', 'pinctrl-[0-9]+'
From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
doc reference errors (make refcheckdocs):
See https://patchwork.ozlabs.org/patch/1533169
This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit.
On 2021-09-24 12:20, Sam Shih wrote:
> Add basic chip support for Mediatek mt7986a, include
> uart nodes with correct clocks, rng node with correct clock,
> and watchdog node and mt7986a pinctrl node.
>
> Add cpu node, timer node, gic node, psci and reserved-memory node
> for ARM Trusted Firmware,
>
> Add clock controller nodes, include 40M clock source, topckgen,
> infracfg,
> apmixedsys and ethernet subsystem.
>
> Signed-off-by: Sam Shih <[email protected]>
> ---
> v3: used the stdout-path instead of console=ttyS0
> v2: modified clock and uart node due to clock driver updated
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 54 +++++
> arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 227 +++++++++++++++++++
> 3 files changed, 282 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a.dtsi
[...]
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupt-parent = <&gic>;
> + clock-frequency = <13000000>;
No. Please fix your firmware to program CNTFRQ_EL0 on all CPUs.
This may have been OK in 2011, but not anymore.
> + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + compatible = "simple-bus";
> + ranges;
> +
> + gic: interrupt-controller@c000000 {
> + compatible = "arm,gic-v3";
> + #interrupt-cells = <3>;
> + interrupt-parent = <&gic>;
> + interrupt-controller;
> + reg = <0 0x0c000000 0 0x40000>,
> + <0 0x0c080000 0 0x200000>;
This looks wrong. 128kB per redistributor frames and 4 CPUs do
no result in 2MB worth of MMIO.
This is also missing the GICV/GICV/GICH regions that are exposed
by the CPUs directly.
M.
--
Jazz is not dead. It just smells funny...
Add basic chip support for Mediatek mt7986a, include
uart nodes with correct clocks, rng node with correct clock,
and watchdog node and mt7986a pinctrl node.
Add cpu node, timer node, gic node, psci and reserved-memory node
for ARM Trusted Firmware,
Add clock controller nodes, include 40M clock source, topckgen, infracfg,
apmixedsys and ethernet subsystem.
Signed-off-by: Sam Shih <[email protected]>
---
v4: added missing gic register bases, and fixed range of GICR
v3: used the stdout-path instead of console=ttyS0
v2: modified clock and uart node due to clock driver updated
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 54 +++++
arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 230 +++++++++++++++++++
3 files changed, 285 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 4f68ebed2e31..e6c3a73b9e4a 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
new file mode 100644
index 000000000000..e210d03ba70a
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+/dts-v1/;
+#include "mt7986a.dtsi"
+
+/ {
+ model = "MediaTek MT7986a RFB";
+ compatible = "mediatek,mt7986a-rfb";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs = "earlycon=uart8250,mmio32,0x11002000 swiotlb=512";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+};
+
+&pio {
+ uart1_pins: uart1-pins-42-to-45 {
+ mux {
+ function = "uart";
+ groups = "uart1";
+ };
+ };
+
+ uart2_pins: uart1-pins-46-to-49 {
+ mux {
+ function = "uart";
+ groups = "uart2";
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
new file mode 100644
index 000000000000..84fd044ae673
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -0,0 +1,230 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/mt7986-clk.h>
+
+/ {
+ compatible = "mediatek,mt7986a";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clk40m: oscillator@0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <40000000>;
+ clock-output-names = "clkxtal";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x2>;
+ #cooling-cells = <2>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ enable-method = "psci";
+ compatible = "arm,cortex-a53";
+ reg = <0x3>;
+ #cooling-cells = <2>;
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ /* 192 KiB reserved for ARM Trusted Firmware (BL31) */
+ secmon_reserved: secmon@43000000 {
+ reg = <0 0x43000000 0 0x30000>;
+ no-map;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ clock-frequency = <13000000>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ gic: interrupt-controller@c000000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x0c000000 0 0x40000>, /* GICD */
+ <0 0x0c080000 0 0x80000>, /* GICR */
+ <0 0x0c400000 0 0x2000>, /* GICC */
+ <0 0x0c410000 0 0x1000>, /* GICH */
+ <0 0x0c420000 0 0x2000>; /* GICV */
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ infracfg: infracfg@10001000 {
+ compatible = "mediatek,mt7986-infracfg", "syscon";
+ reg = <0 0x10001000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ topckgen: topckgen@1001b000 {
+ compatible = "mediatek,mt7986-topckgen", "syscon";
+ reg = <0 0x1001B000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ watchdog: watchdog@1001c000 {
+ compatible = "mediatek,mt7986-wdt",
+ "mediatek,mt6589-wdt";
+ reg = <0 0x1001c000 0 0x1000>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ #reset-cells = <1>;
+ status = "disabled";
+ };
+
+ apmixedsys: apmixedsys@1001e000 {
+ compatible = "mediatek,mt7986-apmixedsys";
+ reg = <0 0x1001E000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ pio: pinctrl@1001f000 {
+ compatible = "mediatek,mt7986a-pinctrl";
+ reg = <0 0x1001f000 0 0x1000>,
+ <0 0x11c30000 0 0x1000>,
+ <0 0x11c40000 0 0x1000>,
+ <0 0x11e20000 0 0x1000>,
+ <0 0x11e30000 0 0x1000>,
+ <0 0x11f00000 0 0x1000>,
+ <0 0x11f10000 0 0x1000>,
+ <0 0x1000b000 0 0x1000>;
+ reg-names = "gpio_base", "iocfg_rt_base", "iocfg_rb_base",
+ "iocfg_lt_base", "iocfg_lb_base", "iocfg_tr_base",
+ "iocfg_tl_base", "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 100>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ #interrupt-cells = <2>;
+ };
+
+ sgmiisys0: syscon@10060000 {
+ compatible = "mediatek,mt7986-sgmiisys_0",
+ "syscon";
+ reg = <0 0x10060000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ sgmiisys1: syscon@10070000 {
+ compatible = "mediatek,mt7986-sgmiisys_1",
+ "syscon";
+ reg = <0 0x10070000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ trng: trng@1020f000 {
+ compatible = "mediatek,mt7986-rng",
+ "mediatek,mt7623-rng";
+ reg = <0 0x1020f000 0 0x100>;
+ clocks = <&infracfg CLK_INFRA_TRNG_CK>;
+ clock-names = "rng";
+ status = "disabled";
+ };
+
+ uart0: serial@11002000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11002000 0 0x400>;
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART0_SEL>,
+ <&infracfg CLK_INFRA_UART0_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&topckgen CLK_TOP_UART_SEL>,
+ <&infracfg CLK_INFRA_UART0_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_XTAL>,
+ <&topckgen CLK_TOP_UART_SEL>;
+ status = "disabled";
+ };
+
+ uart1: serial@11003000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11003000 0 0x400>;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART1_SEL>,
+ <&infracfg CLK_INFRA_UART1_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&infracfg CLK_INFRA_UART1_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+ status = "disabled";
+ };
+
+ uart2: serial@11004000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11004000 0 0x400>;
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART2_SEL>,
+ <&infracfg CLK_INFRA_UART2_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&infracfg CLK_INFRA_UART2_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+ status = "disabled";
+ };
+
+ ethsys: syscon@15000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mediatek,mt7986-ethsys",
+ "syscon";
+ reg = <0 0x15000000 0 0x1000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ };
+
+};
--
2.29.2
Add basic chip support for Mediatek mt7986b, include
uart nodes with correct clocks, rng node with correct clock,
and watchdog node and mt7986b pinctrl node.
Add cpu node, timer node, gic node, psci and reserved-memory node
for ARM Trusted Firmware,
Add clock controller nodes, include 40M clock source, topckgen, infracfg,
apmixedsys and ethernet subsystem.
Signed-off-by: Sam Shih <[email protected]>
---
v4: added missing gic register bases, and fixed range of GICR
v3: used the stdout-path instead of console=ttyS0
v2: modified clock and uart node due to clock driver updated
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts | 26 +++
arch/arm64/boot/dts/mediatek/mt7986b.dtsi | 230 +++++++++++++++++++
3 files changed, 257 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986b.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index e6c3a73b9e4a..d555e43d1ccc 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
new file mode 100644
index 000000000000..95a202505bb2
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+/dts-v1/;
+#include "mt7986b.dtsi"
+
+/ {
+ model = "MediaTek MT7986b RFB";
+ compatible = "mediatek,mt7986b-rfb";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs = "earlycon=uart8250,mmio32,0x11002000 swiotlb=512";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b.dtsi b/arch/arm64/boot/dts/mediatek/mt7986b.dtsi
new file mode 100644
index 000000000000..06c3381a5170
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986b.dtsi
@@ -0,0 +1,230 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/mt7986-clk.h>
+
+/ {
+ compatible = "mediatek,mt7986b";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clk40m: oscillator@0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <40000000>;
+ clock-output-names = "clkxtal";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x2>;
+ #cooling-cells = <2>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ enable-method = "psci";
+ compatible = "arm,cortex-a53";
+ reg = <0x3>;
+ #cooling-cells = <2>;
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ /* 192 KiB reserved for ARM Trusted Firmware (BL31) */
+ secmon_reserved: secmon@43000000 {
+ reg = <0 0x43000000 0 0x30000>;
+ no-map;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ clock-frequency = <13000000>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ gic: interrupt-controller@c000000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x0c000000 0 0x40000>, /* GICD */
+ <0 0x0c080000 0 0x80000>, /* GICR */
+ <0 0x0c400000 0 0x2000>, /* GICC */
+ <0 0x0c410000 0 0x1000>, /* GICH */
+ <0 0x0c420000 0 0x2000>; /* GICV */
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ infracfg: infracfg@10001000 {
+ compatible = "mediatek,mt7986-infracfg", "syscon";
+ reg = <0 0x10001000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ topckgen: topckgen@1001b000 {
+ compatible = "mediatek,mt7986-topckgen", "syscon";
+ reg = <0 0x1001B000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ watchdog: watchdog@1001c000 {
+ compatible = "mediatek,mt7986-wdt",
+ "mediatek,mt6589-wdt";
+ reg = <0 0x1001c000 0 0x1000>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ #reset-cells = <1>;
+ status = "disabled";
+ };
+
+ apmixedsys: apmixedsys@1001e000 {
+ compatible = "mediatek,mt7986-apmixedsys";
+ reg = <0 0x1001E000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ pio: pinctrl@1001f000 {
+ compatible = "mediatek,mt7986b-pinctrl";
+ reg = <0 0x1001f000 0 0x1000>,
+ <0 0x11c30000 0 0x1000>,
+ <0 0x11c40000 0 0x1000>,
+ <0 0x11e20000 0 0x1000>,
+ <0 0x11e30000 0 0x1000>,
+ <0 0x11f00000 0 0x1000>,
+ <0 0x11f10000 0 0x1000>,
+ <0 0x1000b000 0 0x1000>;
+ reg-names = "gpio_base", "iocfg_rt_base", "iocfg_rb_base",
+ "iocfg_lt_base", "iocfg_lb_base", "iocfg_tr_base",
+ "iocfg_tl_base", "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 41>, <&pio 66 66 35>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ #interrupt-cells = <2>;
+ };
+
+ sgmiisys0: syscon@10060000 {
+ compatible = "mediatek,mt7986-sgmiisys_0",
+ "syscon";
+ reg = <0 0x10060000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ sgmiisys1: syscon@10070000 {
+ compatible = "mediatek,mt7986-sgmiisys_1",
+ "syscon";
+ reg = <0 0x10070000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ trng: trng@1020f000 {
+ compatible = "mediatek,mt7986-rng",
+ "mediatek,mt7623-rng";
+ reg = <0 0x1020f000 0 0x100>;
+ clocks = <&infracfg CLK_INFRA_TRNG_CK>;
+ clock-names = "rng";
+ status = "disabled";
+ };
+
+ uart0: serial@11002000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11002000 0 0x400>;
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART0_SEL>,
+ <&infracfg CLK_INFRA_UART0_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&topckgen CLK_TOP_UART_SEL>,
+ <&infracfg CLK_INFRA_UART0_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_XTAL>,
+ <&topckgen CLK_TOP_UART_SEL>;
+ status = "disabled";
+ };
+
+ uart1: serial@11003000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11003000 0 0x400>;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART1_SEL>,
+ <&infracfg CLK_INFRA_UART1_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&infracfg CLK_INFRA_UART1_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+ status = "disabled";
+ };
+
+ uart2: serial@11004000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11004000 0 0x400>;
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART2_SEL>,
+ <&infracfg CLK_INFRA_UART2_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&infracfg CLK_INFRA_UART2_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+ status = "disabled";
+ };
+
+ ethsys: syscon@15000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mediatek,mt7986-ethsys",
+ "syscon";
+ reg = <0 0x15000000 0 0x1000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ };
+
+};
--
2.29.2
This updates bindings for MT7986 pinctrl driver. The
difference of pinctrl between mt7986a and mt7986b is that pin-41 to pin-65
do not exist on mt7986b
Signed-off-by: Sam Shih <[email protected]>
---
v6 : fixed yamllint warnings/errors v2
v5 : fixed yamllint warnings/errors v1
v4 : used yaml format instead of txt format document
v3 : make mt7986 pinctrl bindings as a separate file
v2 : deleted the redundant description of mt7986a/mt7986b
---
.../pinctrl/mediatek,mt7986-pinctrl.yaml | 361 ++++++++++++++++++
1 file changed, 361 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
new file mode 100644
index 000000000000..cde842d093dc
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
@@ -0,0 +1,361 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/mediatek,mt7986-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek MT7986 Pin Controller Device Tree Bindings
+
+maintainers:
+ - Sean Wang <[email protected]>
+
+description: |+
+ The MediaTek's MT7986 Pin controller is used to control SoC pins.
+
+properties:
+ compatible:
+ enum:
+ - mediatek,mt7986a-pinctrl
+ - mediatek,mt7986b-pinctrl
+
+ reg:
+ minItems: 8
+ maxItems: 8
+
+ reg-names:
+ items:
+ - const: gpio_base
+ - const: iocfg_rt_base
+ - const: iocfg_rb_base
+ - const: iocfg_lt_base
+ - const: iocfg_lb_base
+ - const: iocfg_tr_base
+ - const: iocfg_tl_base
+ - const: eint
+
+ gpio-controller: true
+
+ "#gpio-cells":
+ const: 2
+ description: |
+ Number of cells in GPIO specifier. Since the generic GPIO
+ binding is used, the amount of cells must be specified as 2. See the below
+ mentioned gpio binding representation for description of particular cells.
+
+ gpio-ranges:
+ minItems: 1
+ maxItems: 5
+ description: |
+ GPIO valid number range.
+
+ interrupt-controller: true
+
+ interrupts:
+ maxItems: 1
+
+ "#interrupt-cells":
+ const: 2
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - gpio-controller
+ - "#gpio-cells"
+
+patternProperties:
+ '-[0-9]+$':
+ type: object
+ additionalProperties: false
+
+ patternProperties:
+ 'mux':
+ type: object
+ additionalProperties: false
+ description: |
+ pinmux configuration nodes.
+
+ Valid value function pins (in pin#)
+ ---------------------------------------------------------------------
+ "watchdog" "watchdog" 0
+ "wifi_led" "led" 1, 2
+ "i2c" "i2c" 3, 4
+ "uart1_0" "uart" 7, 8, 9, 10
+ "pcie_clk" "pcie" 9
+ "pcie_wake" "pcie" 10
+ "spi1_0" "spi" 11, 12, 13, 14
+ "pwm1_1" "pwm" 20,
+ "pwm0" "pwm" 21,
+ "pwm1_0" "pwm" 22,
+ "snfi" "flash" 23, 24, 25, 26, 27, 28
+ "spi1_2" "spi" 29, 30, 31, 32
+ "emmc_45" "emmc" 22, 23, 24, 25, 26, 27, 28, 29, 30,
+ 31, 32
+ "spi1_1" "spi" 23, 24, 25, 26
+ "uart1_2" "uart" 29, 30, 31, 32
+ "uart1_1" "uart" 23, 24, 25, 26
+ "uart2_0" "uart" 29, 30, 31, 32
+ "spi0" "spi" 33, 34, 35, 36
+ "spi0_wp_hold" "spi" 37, 38
+ "uart1_3_rx_tx" "uart" 35, 36
+ "uart1_3_cts_rts" "uart" 37, 38
+ "uart2_1" "uart" 33, 34, 35, 36
+ "spi1_3" "spi" 33, 34, 35, 36
+ "uart0" "uart" 39, 40
+ "pcie_pereset" "pcie" 41
+ "uart1" "uart" 42, 43, 44, 45
+ "uart2" "uart" 46, 47, 48, 49
+ "emmc_51" "emmc" 50, 51, 52, 53, 54, 55, 56, 57, 57,
+ 59, 60, 61
+ "pcm" "audio" 62, 63, 64, 65
+ "i2s" "audio" 62, 63, 64, 65
+ "switch_int" "eth" 66
+ "mdc_mdio" "eth" 67
+
+ $ref: "/schemas/pinctrl/pinmux-node.yaml"
+ properties:
+ function:
+ description: |
+ A string containing the name of the function to mux to the group.
+ There is no "audio", "pcie" functions on mt7986b, you can only use
+ those functions on mt7986a.
+ enum: [audio, emmc, eth, i2c, led, flash, pcie, pwm, spi, uart,
+ watchdog, wifi]
+ groups:
+ description: |
+ An array of strings. Each string contains the name of a group.
+ There is no "pcie_pereset", "uart1", "uart2" "emmc_51", "pcm",
+ and "i2s" groups on mt7986b, you can only use those groups on
+ mt7986a.
+ required:
+ - function
+ - groups
+
+ allOf:
+ - if:
+ properties:
+ function:
+ const: audio
+ then:
+ properties:
+ groups:
+ enum: [pcm, i2s]
+ - if:
+ properties:
+ function:
+ const: emmc
+ then:
+ properties:
+ groups:
+ enum: [emmc, emmc_rst]
+ - if:
+ properties:
+ function:
+ const: eth
+ then:
+ properties:
+ groups:
+ enum: [switch_int, mdc_mdio]
+ - if:
+ properties:
+ function:
+ const: i2c
+ then:
+ properties:
+ groups:
+ enum: [i2c]
+ - if:
+ properties:
+ function:
+ const: led
+ then:
+ properties:
+ groups:
+ enum: [wifi_led]
+ - if:
+ properties:
+ function:
+ const: flash
+ then:
+ properties:
+ groups:
+ enum: [snfi]
+ - if:
+ properties:
+ function:
+ const: pcie
+ then:
+ properties:
+ groups:
+ enum: [pcie_clk, pcie_wake, pcie_pereset]
+ - if:
+ properties:
+ function:
+ const: pwm
+ then:
+ properties:
+ groups:
+ enum: [pwm0, pwm1_0, pwm1_1]
+ - if:
+ properties:
+ function:
+ const: spi
+ then:
+ properties:
+ groups:
+ enum: [spi0, spi0_wp_hold, spi1_0, spi1_1, spi1_2, spi1_3]
+ - if:
+ properties:
+ function:
+ const: uart
+ then:
+ properties:
+ groups:
+ enum: [uart1_0, uart1_1, uart1_2, uart1_3_rx_tx,
+ uart1_3_cts_rts, uart2_0, uart2_1, uart0, uart1, uart2]
+ - if:
+ properties:
+ function:
+ const: watchdog
+ then:
+ properties:
+ groups:
+ enum: [watchdog]
+ - if:
+ properties:
+ function:
+ const: wifi
+ then:
+ properties:
+ groups:
+ enum: [wf_2g, wf_5g, wf_dbdc]
+ 'conf':
+ type: object
+ additionalProperties: false
+ description: |
+ pinconf configuration nodes.
+ $ref: "/schemas/pinctrl/pincfg-node.yaml"
+
+ properties:
+ pins:
+ description: |
+ An array of strings. Each string contains the name of a pin.
+ There is no PIN 41 to PIN 65 above on mt7686b, you can only use
+ those pins on mt7986a.
+ enum: [SYS_WATCHDOG, WF2G_LED, WF5G_LED, I2C_SCL, I2C_SDA, GPIO_0,
+ GPIO_1, GPIO_2, GPIO_3, GPIO_4, GPIO_5, GPIO_6, GPIO_7,
+ GPIO_8, GPIO_9, GPIO_10, GPIO_11, GPIO_12, GPIO_13, GPIO_14,
+ GPIO_15, PWM0, PWM1, SPI0_CLK, SPI0_MOSI, SPI0_MISO, SPI0_CS,
+ SPI0_HOLD, SPI0_WP, SPI1_CLK, SPI1_MOSI, SPI1_MISO, SPI1_CS,
+ SPI2_CLK, SPI2_MOSI, SPI2_MISO, SPI2_CS, SPI2_HOLD, SPI2_WP,
+ UART0_RXD, UART0_TXD, PCIE_PERESET_N, UART1_RXD, UART1_TXD,
+ UART1_CTS, UART1_RTS, UART2_RXD, UART2_TXD, UART2_CTS,
+ UART2_RTS, EMMC_DATA_0, EMMC_DATA_1, EMMC_DATA_2,
+ EMMC_DATA_3, EMMC_DATA_4, EMMC_DATA_5, EMMC_DATA_6,
+ EMMC_DATA_7, EMMC_CMD, EMMC_CK, EMMC_DSL, EMMC_RSTB, PCM_DTX,
+ PCM_DRX, PCM_CLK, PCM_FS, MT7531_INT, SMI_MDC, SMI_MDIO,
+ WF0_DIG_RESETB, WF0_CBA_RESETB, WF0_XO_REQ, WF0_TOP_CLK,
+ WF0_TOP_DATA, WF0_HB1, WF0_HB2, WF0_HB3, WF0_HB4, WF0_HB0,
+ WF0_HB0_B, WF0_HB5, WF0_HB6, WF0_HB7, WF0_HB8, WF0_HB9,
+ WF0_HB10, WF1_DIG_RESETB, WF1_CBA_RESETB, WF1_XO_REQ,
+ WF1_TOP_CLK, WF1_TOP_DATA, WF1_HB1, WF1_HB2, WF1_HB3,
+ WF1_HB4, WF1_HB0, WF1_HB0_B, WF1_HB5, WF1_HB6, WF1_HB7,
+ WF1_HB8]
+
+ bias-disable: true
+
+ bias-pull-up: true
+
+ bias-pull-down: true
+
+ input-enable: true
+
+ input-disable: true
+
+ output-enable: true
+
+ output-low: true
+
+ output-high: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ drive-strength:
+ enum: [2, 4, 6, 8, 10, 12, 14, 16]
+
+ mediatek,pull-up-adv:
+ description: |
+ Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
+ Pull up setings for 2 pull resistors, R0 and R1. Valid arguments
+ are described as below:
+ 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+ 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+ 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+ 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+
+ mediatek,pull-down-adv:
+ description: |
+ Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
+ Pull down setings for 2 pull resistors, R0 and R1. Valid arguments
+ are described as below:
+ 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+ 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+ 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+ 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+
+ required:
+ - pins
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ pio: pinctrl@1001f000 {
+ compatible = "mediatek,mt7986a-pinctrl";
+ reg = <0 0x1001f000 0 0x1000>,
+ <0 0x11c30000 0 0x1000>,
+ <0 0x11c40000 0 0x1000>,
+ <0 0x11e20000 0 0x1000>,
+ <0 0x11e30000 0 0x1000>,
+ <0 0x11f00000 0 0x1000>,
+ <0 0x11f10000 0 0x1000>,
+ <0 0x1000b000 0 0x1000>;
+ reg-names = "gpio_base", "iocfg_rt_base", "iocfg_rb_base",
+ "iocfg_lt_base", "iocfg_lb_base", "iocfg_tr_base",
+ "iocfg_tl_base", "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 100>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ #interrupt-cells = <2>;
+
+ uart1_pins: uart1-pins-42-to-45 {
+ mux {
+ function = "uart";
+ groups = "uart1";
+ };
+ };
+
+ uart2_pins: uart1-pins-46-to-49 {
+ mux {
+ function = "uart";
+ groups = "uart2";
+ };
+ };
+
+ };
+ };
--
2.29.2
On Mon, 04 Oct 2021 10:12:08 +0100,
Sam Shih <[email protected]> wrote:
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupt-parent = <&gic>;
> + clock-frequency = <13000000>;
I mentioned it last time[1] , but you seem to have ignored my comment.
This property isn't an acceptable workaround on new systems. Please
fix your firmware and drop this clock-frequency property.
M.
[1] https://lore.kernel.org/r/[email protected]
--
Without deviation from the norm, progress is not possible.
On Mon, 04 Oct 2021 10:12:08 +0100,
Sam Shih <[email protected]> wrote:
>
> + gic: interrupt-controller@c000000 {
> + compatible = "arm,gic-v3";
> + #interrupt-cells = <3>;
> + interrupt-parent = <&gic>;
> + interrupt-controller;
> + reg = <0 0x0c000000 0 0x40000>, /* GICD */
> + <0 0x0c080000 0 0x80000>, /* GICR */
> + <0 0x0c400000 0 0x2000>, /* GICC */
> + <0 0x0c410000 0 0x1000>, /* GICH */
> + <0 0x0c420000 0 0x2000>; /* GICV */
> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
> + };
Also, the GICD region is totally wrong. It is 64kB at all times. I
don't know where you get this 256kB figure from.
M.
--
Without deviation from the norm, progress is not possible.
On 2021-10-04 10:16, Sam Shih wrote:
> Add basic chip support for Mediatek mt7986b, include
> uart nodes with correct clocks, rng node with correct clock,
> and watchdog node and mt7986b pinctrl node.
>
> Add cpu node, timer node, gic node, psci and reserved-memory node
> for ARM Trusted Firmware,
>
> Add clock controller nodes, include 40M clock source, topckgen,
> infracfg,
> apmixedsys and ethernet subsystem.
>
> Signed-off-by: Sam Shih <[email protected]>
> ---
> v4: added missing gic register bases, and fixed range of GICR
> v3: used the stdout-path instead of console=ttyS0
> v2: modified clock and uart node due to clock driver updated
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts | 26 +++
> arch/arm64/boot/dts/mediatek/mt7986b.dtsi | 230 +++++++++++++++++++
> 3 files changed, 257 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt7986b.dtsi
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile
> b/arch/arm64/boot/dts/mediatek/Makefile
> index e6c3a73b9e4a..d555e43d1ccc 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
> b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
> new file mode 100644
> index 000000000000..95a202505bb2
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
> @@ -0,0 +1,26 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Author: Sam.Shih <[email protected]>
> + */
> +
> +/dts-v1/;
> +#include "mt7986b.dtsi"
> +
> +/ {
> + model = "MediaTek MT7986b RFB";
> + compatible = "mediatek,mt7986b-rfb";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + bootargs = "earlycon=uart8250,mmio32,0x11002000 swiotlb=512";
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986b.dtsi
> b/arch/arm64/boot/dts/mediatek/mt7986b.dtsi
> new file mode 100644
> index 000000000000..06c3381a5170
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986b.dtsi
> @@ -0,0 +1,230 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Author: Sam.Shih <[email protected]>
> + */
> +
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/mt7986-clk.h>
> +
> +/ {
> + compatible = "mediatek,mt7986b";
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + clk40m: oscillator@0 {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <40000000>;
> + clock-output-names = "clkxtal";
> + };
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + cpu0: cpu@0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + enable-method = "psci";
> + reg = <0x0>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu1: cpu@1 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + enable-method = "psci";
> + reg = <0x1>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu2: cpu@2 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + enable-method = "psci";
> + reg = <0x2>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu3: cpu@3 {
> + device_type = "cpu";
> + enable-method = "psci";
> + compatible = "arm,cortex-a53";
> + reg = <0x3>;
> + #cooling-cells = <2>;
> + };
> + };
> +
> + psci {
> + compatible = "arm,psci-0.2";
> + method = "smc";
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> + /* 192 KiB reserved for ARM Trusted Firmware (BL31) */
> + secmon_reserved: secmon@43000000 {
> + reg = <0 0x43000000 0 0x30000>;
> + no-map;
> + };
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupt-parent = <&gic>;
> + clock-frequency = <13000000>;
As previously mentioned, please fix your firmware and drop this.
> + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + compatible = "simple-bus";
> + ranges;
> +
> + gic: interrupt-controller@c000000 {
> + compatible = "arm,gic-v3";
> + #interrupt-cells = <3>;
> + interrupt-parent = <&gic>;
> + interrupt-controller;
> + reg = <0 0x0c000000 0 0x40000>, /* GICD */
This is not a valid value for GICD.
Thanks,
M.
Add basic chip support for Mediatek mt7986a, include
uart nodes with correct clocks, rng node with correct clock,
and watchdog node and mt7986a pinctrl node.
Add cpu node, timer node, gic node, psci and reserved-memory node
for ARM Trusted Firmware,
Add clock controller nodes, include 40M clock source, topckgen, infracfg,
apmixedsys and ethernet subsystem.
Signed-off-by: Sam Shih <[email protected]>
---
v5: follow reviewr's comment: removed clock freqency node in timer due to
we have set CNTFRQ_EL0 in ATF firmware, and also corrected GICD range
v4: added missing gic register bases, and fixed range of GICR
v3: used the stdout-path instead of console=ttyS0
v2: modified clock and uart node due to clock driver updated
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 54 +++++
arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 229 +++++++++++++++++++
3 files changed, 284 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 4f68ebed2e31..e6c3a73b9e4a 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
new file mode 100644
index 000000000000..e210d03ba70a
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+/dts-v1/;
+#include "mt7986a.dtsi"
+
+/ {
+ model = "MediaTek MT7986a RFB";
+ compatible = "mediatek,mt7986a-rfb";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs = "earlycon=uart8250,mmio32,0x11002000 swiotlb=512";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+};
+
+&pio {
+ uart1_pins: uart1-pins-42-to-45 {
+ mux {
+ function = "uart";
+ groups = "uart1";
+ };
+ };
+
+ uart2_pins: uart1-pins-46-to-49 {
+ mux {
+ function = "uart";
+ groups = "uart2";
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
new file mode 100644
index 000000000000..d126fb7218c6
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -0,0 +1,229 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/mt7986-clk.h>
+
+/ {
+ compatible = "mediatek,mt7986a";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clk40m: oscillator@0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <40000000>;
+ clock-output-names = "clkxtal";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x2>;
+ #cooling-cells = <2>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ enable-method = "psci";
+ compatible = "arm,cortex-a53";
+ reg = <0x3>;
+ #cooling-cells = <2>;
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ /* 192 KiB reserved for ARM Trusted Firmware (BL31) */
+ secmon_reserved: secmon@43000000 {
+ reg = <0 0x43000000 0 0x30000>;
+ no-map;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ gic: interrupt-controller@c000000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x0c000000 0 0x10000>, /* GICD */
+ <0 0x0c080000 0 0x80000>, /* GICR */
+ <0 0x0c400000 0 0x2000>, /* GICC */
+ <0 0x0c410000 0 0x1000>, /* GICH */
+ <0 0x0c420000 0 0x2000>; /* GICV */
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ infracfg: infracfg@10001000 {
+ compatible = "mediatek,mt7986-infracfg", "syscon";
+ reg = <0 0x10001000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ topckgen: topckgen@1001b000 {
+ compatible = "mediatek,mt7986-topckgen", "syscon";
+ reg = <0 0x1001B000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ watchdog: watchdog@1001c000 {
+ compatible = "mediatek,mt7986-wdt",
+ "mediatek,mt6589-wdt";
+ reg = <0 0x1001c000 0 0x1000>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ #reset-cells = <1>;
+ status = "disabled";
+ };
+
+ apmixedsys: apmixedsys@1001e000 {
+ compatible = "mediatek,mt7986-apmixedsys";
+ reg = <0 0x1001E000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ pio: pinctrl@1001f000 {
+ compatible = "mediatek,mt7986a-pinctrl";
+ reg = <0 0x1001f000 0 0x1000>,
+ <0 0x11c30000 0 0x1000>,
+ <0 0x11c40000 0 0x1000>,
+ <0 0x11e20000 0 0x1000>,
+ <0 0x11e30000 0 0x1000>,
+ <0 0x11f00000 0 0x1000>,
+ <0 0x11f10000 0 0x1000>,
+ <0 0x1000b000 0 0x1000>;
+ reg-names = "gpio_base", "iocfg_rt_base", "iocfg_rb_base",
+ "iocfg_lt_base", "iocfg_lb_base", "iocfg_tr_base",
+ "iocfg_tl_base", "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 100>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ #interrupt-cells = <2>;
+ };
+
+ sgmiisys0: syscon@10060000 {
+ compatible = "mediatek,mt7986-sgmiisys_0",
+ "syscon";
+ reg = <0 0x10060000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ sgmiisys1: syscon@10070000 {
+ compatible = "mediatek,mt7986-sgmiisys_1",
+ "syscon";
+ reg = <0 0x10070000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ trng: trng@1020f000 {
+ compatible = "mediatek,mt7986-rng",
+ "mediatek,mt7623-rng";
+ reg = <0 0x1020f000 0 0x100>;
+ clocks = <&infracfg CLK_INFRA_TRNG_CK>;
+ clock-names = "rng";
+ status = "disabled";
+ };
+
+ uart0: serial@11002000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11002000 0 0x400>;
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART0_SEL>,
+ <&infracfg CLK_INFRA_UART0_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&topckgen CLK_TOP_UART_SEL>,
+ <&infracfg CLK_INFRA_UART0_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_XTAL>,
+ <&topckgen CLK_TOP_UART_SEL>;
+ status = "disabled";
+ };
+
+ uart1: serial@11003000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11003000 0 0x400>;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART1_SEL>,
+ <&infracfg CLK_INFRA_UART1_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&infracfg CLK_INFRA_UART1_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+ status = "disabled";
+ };
+
+ uart2: serial@11004000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11004000 0 0x400>;
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART2_SEL>,
+ <&infracfg CLK_INFRA_UART2_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&infracfg CLK_INFRA_UART2_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+ status = "disabled";
+ };
+
+ ethsys: syscon@15000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mediatek,mt7986-ethsys",
+ "syscon";
+ reg = <0 0x15000000 0 0x1000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ };
+
+};
--
2.29.2
Add basic chip support for Mediatek mt7986b, include
uart nodes with correct clocks, rng node with correct clock,
and watchdog node and mt7986b pinctrl node.
Add cpu node, timer node, gic node, psci and reserved-memory node
for ARM Trusted Firmware,
Add clock controller nodes, include 40M clock source, topckgen, infracfg,
apmixedsys and ethernet subsystem.
Signed-off-by: Sam Shih <[email protected]>
---
v5: follow reviewr's comment: removed clock freqency node in timer due to
we have set CNTFRQ_EL0 in ATF firmware, and also corrected GICD range
v4: added missing gic register bases, and fixed range of GICR
v3: used the stdout-path instead of console=ttyS0
v2: modified clock and uart node due to clock driver updated
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts | 26 +++
arch/arm64/boot/dts/mediatek/mt7986b.dtsi | 229 +++++++++++++++++++
3 files changed, 256 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986b.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index e6c3a73b9e4a..d555e43d1ccc 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
new file mode 100644
index 000000000000..95a202505bb2
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+/dts-v1/;
+#include "mt7986b.dtsi"
+
+/ {
+ model = "MediaTek MT7986b RFB";
+ compatible = "mediatek,mt7986b-rfb";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs = "earlycon=uart8250,mmio32,0x11002000 swiotlb=512";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b.dtsi b/arch/arm64/boot/dts/mediatek/mt7986b.dtsi
new file mode 100644
index 000000000000..318547dde733
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986b.dtsi
@@ -0,0 +1,229 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/mt7986-clk.h>
+
+/ {
+ compatible = "mediatek,mt7986b";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clk40m: oscillator@0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <40000000>;
+ clock-output-names = "clkxtal";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x2>;
+ #cooling-cells = <2>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ enable-method = "psci";
+ compatible = "arm,cortex-a53";
+ reg = <0x3>;
+ #cooling-cells = <2>;
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ /* 192 KiB reserved for ARM Trusted Firmware (BL31) */
+ secmon_reserved: secmon@43000000 {
+ reg = <0 0x43000000 0 0x30000>;
+ no-map;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ gic: interrupt-controller@c000000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x0c000000 0 0x10000>, /* GICD */
+ <0 0x0c080000 0 0x80000>, /* GICR */
+ <0 0x0c400000 0 0x2000>, /* GICC */
+ <0 0x0c410000 0 0x1000>, /* GICH */
+ <0 0x0c420000 0 0x2000>; /* GICV */
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ infracfg: infracfg@10001000 {
+ compatible = "mediatek,mt7986-infracfg", "syscon";
+ reg = <0 0x10001000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ topckgen: topckgen@1001b000 {
+ compatible = "mediatek,mt7986-topckgen", "syscon";
+ reg = <0 0x1001B000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ watchdog: watchdog@1001c000 {
+ compatible = "mediatek,mt7986-wdt",
+ "mediatek,mt6589-wdt";
+ reg = <0 0x1001c000 0 0x1000>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ #reset-cells = <1>;
+ status = "disabled";
+ };
+
+ apmixedsys: apmixedsys@1001e000 {
+ compatible = "mediatek,mt7986-apmixedsys";
+ reg = <0 0x1001E000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ pio: pinctrl@1001f000 {
+ compatible = "mediatek,mt7986b-pinctrl";
+ reg = <0 0x1001f000 0 0x1000>,
+ <0 0x11c30000 0 0x1000>,
+ <0 0x11c40000 0 0x1000>,
+ <0 0x11e20000 0 0x1000>,
+ <0 0x11e30000 0 0x1000>,
+ <0 0x11f00000 0 0x1000>,
+ <0 0x11f10000 0 0x1000>,
+ <0 0x1000b000 0 0x1000>;
+ reg-names = "gpio_base", "iocfg_rt_base", "iocfg_rb_base",
+ "iocfg_lt_base", "iocfg_lb_base", "iocfg_tr_base",
+ "iocfg_tl_base", "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 41>, <&pio 66 66 35>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ #interrupt-cells = <2>;
+ };
+
+ sgmiisys0: syscon@10060000 {
+ compatible = "mediatek,mt7986-sgmiisys_0",
+ "syscon";
+ reg = <0 0x10060000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ sgmiisys1: syscon@10070000 {
+ compatible = "mediatek,mt7986-sgmiisys_1",
+ "syscon";
+ reg = <0 0x10070000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ trng: trng@1020f000 {
+ compatible = "mediatek,mt7986-rng",
+ "mediatek,mt7623-rng";
+ reg = <0 0x1020f000 0 0x100>;
+ clocks = <&infracfg CLK_INFRA_TRNG_CK>;
+ clock-names = "rng";
+ status = "disabled";
+ };
+
+ uart0: serial@11002000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11002000 0 0x400>;
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART0_SEL>,
+ <&infracfg CLK_INFRA_UART0_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&topckgen CLK_TOP_UART_SEL>,
+ <&infracfg CLK_INFRA_UART0_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_XTAL>,
+ <&topckgen CLK_TOP_UART_SEL>;
+ status = "disabled";
+ };
+
+ uart1: serial@11003000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11003000 0 0x400>;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART1_SEL>,
+ <&infracfg CLK_INFRA_UART1_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&infracfg CLK_INFRA_UART1_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+ status = "disabled";
+ };
+
+ uart2: serial@11004000 {
+ compatible = "mediatek,mt7986-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11004000 0 0x400>;
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&infracfg CLK_INFRA_UART2_SEL>,
+ <&infracfg CLK_INFRA_UART2_CK>;
+ clock-names = "baud", "bus";
+ assigned-clocks = <&infracfg CLK_INFRA_UART2_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+ status = "disabled";
+ };
+
+ ethsys: syscon@15000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mediatek,mt7986-ethsys",
+ "syscon";
+ reg = <0 0x15000000 0 0x1000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ };
+
+};
--
2.29.2
On Mon, Oct 04, 2021 at 05:41:40PM +0800, Sam Shih wrote:
> This updates bindings for MT7986 pinctrl driver. The
> difference of pinctrl between mt7986a and mt7986b is that pin-41 to pin-65
> do not exist on mt7986b
>
> Signed-off-by: Sam Shih <[email protected]>
>
> ---
> v6 : fixed yamllint warnings/errors v2
> v5 : fixed yamllint warnings/errors v1
> v4 : used yaml format instead of txt format document
> v3 : make mt7986 pinctrl bindings as a separate file
> v2 : deleted the redundant description of mt7986a/mt7986b
> ---
> .../pinctrl/mediatek,mt7986-pinctrl.yaml | 361 ++++++++++++++++++
> 1 file changed, 361 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
> new file mode 100644
> index 000000000000..cde842d093dc
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
> @@ -0,0 +1,361 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/mediatek,mt7986-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Mediatek MT7986 Pin Controller Device Tree Bindings
> +
> +maintainers:
> + - Sean Wang <[email protected]>
> +
> +description: |+
> + The MediaTek's MT7986 Pin controller is used to control SoC pins.
> +
> +properties:
> + compatible:
> + enum:
> + - mediatek,mt7986a-pinctrl
> + - mediatek,mt7986b-pinctrl
> +
> + reg:
> + minItems: 8
> + maxItems: 8
> +
> + reg-names:
> + items:
> + - const: gpio_base
> + - const: iocfg_rt_base
> + - const: iocfg_rb_base
> + - const: iocfg_lt_base
> + - const: iocfg_lb_base
> + - const: iocfg_tr_base
> + - const: iocfg_tl_base
_base is redundant. Drop.
> + - const: eint
> +
> + gpio-controller: true
> +
> + "#gpio-cells":
> + const: 2
> + description: |
> + Number of cells in GPIO specifier. Since the generic GPIO
> + binding is used, the amount of cells must be specified as 2. See the below
> + mentioned gpio binding representation for description of particular cells.
> +
> + gpio-ranges:
> + minItems: 1
> + maxItems: 5
> + description: |
> + GPIO valid number range.
> +
> + interrupt-controller: true
> +
> + interrupts:
> + maxItems: 1
> +
> + "#interrupt-cells":
> + const: 2
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - gpio-controller
> + - "#gpio-cells"
> +
> +patternProperties:
> + '-[0-9]+$':
This could be a bit more specific. Most new bindings use '-pins$' here.
> + type: object
> + additionalProperties: false
> +
> + patternProperties:
> + 'mux':
Do you really mean '.*mux.*' because that's what is allowed here. If the
node name is really just 'mux', then this isn't a pattern and should be
under 'properties'.
> + type: object
> + additionalProperties: false
> + description: |
> + pinmux configuration nodes.
> +
> + Valid value function pins (in pin#)
> + ---------------------------------------------------------------------
> + "watchdog" "watchdog" 0
> + "wifi_led" "led" 1, 2
> + "i2c" "i2c" 3, 4
> + "uart1_0" "uart" 7, 8, 9, 10
> + "pcie_clk" "pcie" 9
> + "pcie_wake" "pcie" 10
> + "spi1_0" "spi" 11, 12, 13, 14
> + "pwm1_1" "pwm" 20,
> + "pwm0" "pwm" 21,
> + "pwm1_0" "pwm" 22,
> + "snfi" "flash" 23, 24, 25, 26, 27, 28
> + "spi1_2" "spi" 29, 30, 31, 32
> + "emmc_45" "emmc" 22, 23, 24, 25, 26, 27, 28, 29, 30,
> + 31, 32
> + "spi1_1" "spi" 23, 24, 25, 26
> + "uart1_2" "uart" 29, 30, 31, 32
> + "uart1_1" "uart" 23, 24, 25, 26
> + "uart2_0" "uart" 29, 30, 31, 32
> + "spi0" "spi" 33, 34, 35, 36
> + "spi0_wp_hold" "spi" 37, 38
> + "uart1_3_rx_tx" "uart" 35, 36
> + "uart1_3_cts_rts" "uart" 37, 38
> + "uart2_1" "uart" 33, 34, 35, 36
> + "spi1_3" "spi" 33, 34, 35, 36
> + "uart0" "uart" 39, 40
> + "pcie_pereset" "pcie" 41
> + "uart1" "uart" 42, 43, 44, 45
> + "uart2" "uart" 46, 47, 48, 49
> + "emmc_51" "emmc" 50, 51, 52, 53, 54, 55, 56, 57, 57,
> + 59, 60, 61
> + "pcm" "audio" 62, 63, 64, 65
> + "i2s" "audio" 62, 63, 64, 65
> + "switch_int" "eth" 66
> + "mdc_mdio" "eth" 67
> +
> + $ref: "/schemas/pinctrl/pinmux-node.yaml"
> + properties:
> + function:
> + description: |
> + A string containing the name of the function to mux to the group.
> + There is no "audio", "pcie" functions on mt7986b, you can only use
> + those functions on mt7986a.
> + enum: [audio, emmc, eth, i2c, led, flash, pcie, pwm, spi, uart,
> + watchdog, wifi]
> + groups:
> + description: |
> + An array of strings. Each string contains the name of a group.
> + There is no "pcie_pereset", "uart1", "uart2" "emmc_51", "pcm",
> + and "i2s" groups on mt7986b, you can only use those groups on
> + mt7986a.
> + required:
> + - function
> + - groups
> +
> + allOf:
> + - if:
> + properties:
> + function:
> + const: audio
> + then:
> + properties:
> + groups:
> + enum: [pcm, i2s]
> + - if:
> + properties:
> + function:
> + const: emmc
> + then:
> + properties:
> + groups:
> + enum: [emmc, emmc_rst]
> + - if:
> + properties:
> + function:
> + const: eth
> + then:
> + properties:
> + groups:
> + enum: [switch_int, mdc_mdio]
> + - if:
> + properties:
> + function:
> + const: i2c
> + then:
> + properties:
> + groups:
> + enum: [i2c]
> + - if:
> + properties:
> + function:
> + const: led
> + then:
> + properties:
> + groups:
> + enum: [wifi_led]
> + - if:
> + properties:
> + function:
> + const: flash
> + then:
> + properties:
> + groups:
> + enum: [snfi]
> + - if:
> + properties:
> + function:
> + const: pcie
> + then:
> + properties:
> + groups:
> + enum: [pcie_clk, pcie_wake, pcie_pereset]
> + - if:
> + properties:
> + function:
> + const: pwm
> + then:
> + properties:
> + groups:
> + enum: [pwm0, pwm1_0, pwm1_1]
> + - if:
> + properties:
> + function:
> + const: spi
> + then:
> + properties:
> + groups:
> + enum: [spi0, spi0_wp_hold, spi1_0, spi1_1, spi1_2, spi1_3]
> + - if:
> + properties:
> + function:
> + const: uart
> + then:
> + properties:
> + groups:
> + enum: [uart1_0, uart1_1, uart1_2, uart1_3_rx_tx,
> + uart1_3_cts_rts, uart2_0, uart2_1, uart0, uart1, uart2]
> + - if:
> + properties:
> + function:
> + const: watchdog
> + then:
> + properties:
> + groups:
> + enum: [watchdog]
> + - if:
> + properties:
> + function:
> + const: wifi
> + then:
> + properties:
> + groups:
> + enum: [wf_2g, wf_5g, wf_dbdc]
> + 'conf':
Same here. pattern or not?
> + type: object
> + additionalProperties: false
> + description: |
> + pinconf configuration nodes.
> + $ref: "/schemas/pinctrl/pincfg-node.yaml"
> +
> + properties:
> + pins:
> + description: |
> + An array of strings. Each string contains the name of a pin.
> + There is no PIN 41 to PIN 65 above on mt7686b, you can only use
> + those pins on mt7986a.
> + enum: [SYS_WATCHDOG, WF2G_LED, WF5G_LED, I2C_SCL, I2C_SDA, GPIO_0,
> + GPIO_1, GPIO_2, GPIO_3, GPIO_4, GPIO_5, GPIO_6, GPIO_7,
> + GPIO_8, GPIO_9, GPIO_10, GPIO_11, GPIO_12, GPIO_13, GPIO_14,
> + GPIO_15, PWM0, PWM1, SPI0_CLK, SPI0_MOSI, SPI0_MISO, SPI0_CS,
> + SPI0_HOLD, SPI0_WP, SPI1_CLK, SPI1_MOSI, SPI1_MISO, SPI1_CS,
> + SPI2_CLK, SPI2_MOSI, SPI2_MISO, SPI2_CS, SPI2_HOLD, SPI2_WP,
> + UART0_RXD, UART0_TXD, PCIE_PERESET_N, UART1_RXD, UART1_TXD,
> + UART1_CTS, UART1_RTS, UART2_RXD, UART2_TXD, UART2_CTS,
> + UART2_RTS, EMMC_DATA_0, EMMC_DATA_1, EMMC_DATA_2,
> + EMMC_DATA_3, EMMC_DATA_4, EMMC_DATA_5, EMMC_DATA_6,
> + EMMC_DATA_7, EMMC_CMD, EMMC_CK, EMMC_DSL, EMMC_RSTB, PCM_DTX,
> + PCM_DRX, PCM_CLK, PCM_FS, MT7531_INT, SMI_MDC, SMI_MDIO,
> + WF0_DIG_RESETB, WF0_CBA_RESETB, WF0_XO_REQ, WF0_TOP_CLK,
> + WF0_TOP_DATA, WF0_HB1, WF0_HB2, WF0_HB3, WF0_HB4, WF0_HB0,
> + WF0_HB0_B, WF0_HB5, WF0_HB6, WF0_HB7, WF0_HB8, WF0_HB9,
> + WF0_HB10, WF1_DIG_RESETB, WF1_CBA_RESETB, WF1_XO_REQ,
> + WF1_TOP_CLK, WF1_TOP_DATA, WF1_HB1, WF1_HB2, WF1_HB3,
> + WF1_HB4, WF1_HB0, WF1_HB0_B, WF1_HB5, WF1_HB6, WF1_HB7,
> + WF1_HB8]
> +
> + bias-disable: true
> +
> + bias-pull-up: true
> +
> + bias-pull-down: true
> +
> + input-enable: true
> +
> + input-disable: true
> +
> + output-enable: true
> +
> + output-low: true
> +
> + output-high: true
> +
> + input-schmitt-enable: true
> +
> + input-schmitt-disable: true
> +
> + drive-strength:
> + enum: [2, 4, 6, 8, 10, 12, 14, 16]
> +
> + mediatek,pull-up-adv:
> + description: |
> + Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
> + Pull up setings for 2 pull resistors, R0 and R1. Valid arguments
> + are described as below:
> + 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
> + 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
> + 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
> + 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1, 2, 3]
> +
> + mediatek,pull-down-adv:
> + description: |
> + Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
> + Pull down setings for 2 pull resistors, R0 and R1. Valid arguments
> + are described as below:
> + 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
> + 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
> + 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
> + 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1, 2, 3]
> +
> + required:
> + - pins
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/irq.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> + soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + pio: pinctrl@1001f000 {
> + compatible = "mediatek,mt7986a-pinctrl";
> + reg = <0 0x1001f000 0 0x1000>,
> + <0 0x11c30000 0 0x1000>,
> + <0 0x11c40000 0 0x1000>,
> + <0 0x11e20000 0 0x1000>,
> + <0 0x11e30000 0 0x1000>,
> + <0 0x11f00000 0 0x1000>,
> + <0 0x11f10000 0 0x1000>,
> + <0 0x1000b000 0 0x1000>;
> + reg-names = "gpio_base", "iocfg_rt_base", "iocfg_rb_base",
> + "iocfg_lt_base", "iocfg_lb_base", "iocfg_tr_base",
> + "iocfg_tl_base", "eint";
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&pio 0 0 100>;
> + interrupt-controller;
> + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-parent = <&gic>;
> + #interrupt-cells = <2>;
> +
> + uart1_pins: uart1-pins-42-to-45 {
> + mux {
> + function = "uart";
> + groups = "uart1";
> + };
> + };
> +
> + uart2_pins: uart1-pins-46-to-49 {
> + mux {
> + function = "uart";
> + groups = "uart2";
> + };
> + };
> +
> + };
> + };
> --
> 2.29.2
>
>