This series replaces the patch "[PATCH 12/12] brcmsmac: support 4313iPA"
with Message-ID: <[email protected]>.
It has been split up into individual patches. Please test this series
especially if you had issues with the original commit b6fc28a that was
reverted.
Cc: Jonas Gorski <[email protected]>
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Arend van Spriel (13):
brcmsmac: cosmetic change in phy_lcn.c
brcmsmac: change pa_gain for bcm4313 iPA
brcmsmac: use ARRAY_SIZE in phytbl_lcn.c
brcmsmac: add switch control table for BCM4313 iPA BT-combo cards
brcmsmac: add debug info message providing phy and radio info
brcmsmac: update transmit gain table for lcn phy
brcmsmac: change lcnphy receive i/q calibration routine
brcmsmac: fix TSSI idle estimation
brcmsmac: avoid calling set_txpwr_by_index() twice
brcmsmac: rework switch control table init including iPA BT-combo
brcmsmac: correct phy registers for TSSI-based power control
brcmsmac: reinitialize TSSI power control upon channel switch
brcmsmac: add support for BCM4313 iPA variant
drivers/net/wireless/brcm80211/brcmsmac/main.c | 4 +-
.../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 397 +++++++++++--------
.../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c | 405 +++++++++++---------
.../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h | 1 +
4 files changed, 475 insertions(+), 332 deletions(-)
--
1.7.10.4
The function wlc_lcnphy_load_tx_gain_table() has a target PA
gain specified for the iPA variant of the bcm4313. This gain
value is reduced to avoid PA distortion. The if-statement is
removed because it was rather redundant in the first place.
Please not that this patch does not provide full iPA support.
Cc: Jonas Gorski <[email protected]>
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Reviewed-by: Hante Meuleman <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 7 ++-----
1 file changed, 2 insertions(+), 5 deletions(-)
diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index e646ba0..8dc5d0f 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -4282,13 +4282,10 @@ wlc_lcnphy_load_tx_gain_table(struct brcms_phy *pi,
u16 pa_gain;
u16 gm_gain;
- if (CHSPEC_IS5G(pi->radio_chanspec))
- pa_gain = 0x70;
- else
- pa_gain = 0x70;
-
if (pi->sh->boardflags & BFL_FEM)
pa_gain = 0x10;
+ else
+ pa_gain = 0x60;
tab.tbl_id = LCNPHY_TBL_ID_TXPWRCTL;
tab.tbl_width = 32;
tab.tbl_len = 1;
--
1.7.10.4
The bcm4313 iPA BT-WLAN combo cards need to be initialized with
a different switch control table. This patch adds that table.
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
.../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c | 72 ++++++++++++++++++++
.../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h | 1 +
2 files changed, 73 insertions(+)
diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
index deae3a7..36c41df 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
@@ -2044,6 +2044,73 @@ static const u16 dot11lcn_sw_ctrl_tbl_4313_rev0[] = {
0x0005,
};
+static const u16 dot11lcn_sw_ctrl_tbl_4313_ipa_rev0_combo[] = {
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+};
+
static const u16 dot11lcn_sw_ctrl_tbl_rev0[] = {
0x0004,
0x0004,
@@ -2808,6 +2875,11 @@ const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313 = {
ARRAY_SIZE(dot11lcn_sw_ctrl_tbl_4313_rev0), 15, 0, 16
};
+const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_bt_ipa = {
+ &dot11lcn_sw_ctrl_tbl_4313_ipa_rev0_combo,
+ ARRAY_SIZE(dot11lcn_sw_ctrl_tbl_4313_ipa_rev0_combo), 15, 0, 16
+};
+
const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_epa = {
&dot11lcn_sw_ctrl_tbl_4313_epa_rev0,
ARRAY_SIZE(dot11lcn_sw_ctrl_tbl_4313_epa_rev0), 15, 0, 16
diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h
index 5f75e16..489422a 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h
@@ -20,6 +20,7 @@
extern const struct phytbl_info dot11lcnphytbl_rx_gain_info_rev0[];
extern const u32 dot11lcnphytbl_rx_gain_info_sz_rev0;
extern const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313;
+extern const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_bt_ipa;
extern const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_epa;
extern const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_epa_combo;
extern const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_bt_epa;
--
1.7.10.4
Hi
On Tue, Aug 13, 2013 at 10:46 PM, Arend van Spriel <[email protected]> wrote:
> On 08/13/2013 10:09 PM, David Herrmann wrote:
>>
>> Hi
>>
>> On Tue, Aug 13, 2013 at 10:03 PM, Arend van Spriel <[email protected]>
>> wrote:
>>>
>>> This series replaces the patch "[PATCH 12/12] brcmsmac: support 4313iPA"
>>> with Message-ID: <[email protected]>.
>>>
>>> It has been split up into individual patches. Please test this series
>>> especially if you had issues with the original commit b6fc28a that was
>>> reverted.
>>>
>>> Cc: Jonas Gorski <[email protected]>
>>> Cc: David Herrmann <[email protected]>
>>> Cc: Maximilian Engelhardt <[email protected]>
>>> Cc: David Costa <[email protected]>
>>
>>
>> Is this available in a public branch that I can merge? And what should
>> be used as base? 3.11-rc5? linux-next?
>
>
> Indeed I should have mentioned. It applies on v3.11-rc5 for sure. Did not
> try linux-next.
All 13 patches applied cleanly on top of 3.11-rc5, everything works
fine even after a dozen of reconnects to different networks. No
additional delays.
Consider this whole series:
Tested-by: David Herrmann <[email protected]>
card info: Broadcom Corporation BCM4313 802.11b/g/n (0a5c:219c)
(builtin into my old Intel Atom N450 board)
I tested with 802.11g networks. I have only a/g networks here. I don't
know whether that matters.
Cheers
David
On 08/14/2013 12:33 PM, David Herrmann wrote:
> Hi
>
> On Tue, Aug 13, 2013 at 10:46 PM, Arend van Spriel <[email protected]> wrote:
>> On 08/13/2013 10:09 PM, David Herrmann wrote:
>>>
>>> Hi
>>>
>>> On Tue, Aug 13, 2013 at 10:03 PM, Arend van Spriel <[email protected]>
>>> wrote:
>>>>
>>>> This series replaces the patch "[PATCH 12/12] brcmsmac: support 4313iPA"
>>>> with Message-ID: <[email protected]>.
>>>>
>>>> It has been split up into individual patches. Please test this series
>>>> especially if you had issues with the original commit b6fc28a that was
>>>> reverted.
>>>>
>>>> Cc: Jonas Gorski <[email protected]>
>>>> Cc: David Herrmann <[email protected]>
>>>> Cc: Maximilian Engelhardt <[email protected]>
>>>> Cc: David Costa <[email protected]>
>>>
>>>
>>> Is this available in a public branch that I can merge? And what should
>>> be used as base? 3.11-rc5? linux-next?
>>
>>
>> Indeed I should have mentioned. It applies on v3.11-rc5 for sure. Did not
>> try linux-next.
>
> All 13 patches applied cleanly on top of 3.11-rc5, everything works
> fine even after a dozen of reconnects to different networks. No
> additional delays.
>
> Consider this whole series:
> Tested-by: David Herrmann <[email protected]>
>
> card info: Broadcom Corporation BCM4313 802.11b/g/n (0a5c:219c)
> (builtin into my old Intel Atom N450 board)
> I tested with 802.11g networks. I have only a/g networks here. I don't
> know whether that matters.
As this series modifies the phy code, I would say no.
Thanks for verifying this works for you.
Regards,
Arend
Rework the code path in lcnphy tbl_init() for switch control
table programming. This also takes the iPA BT-combo card into
account.
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
.../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 31 ++++++++++----------
1 file changed, 16 insertions(+), 15 deletions(-)
diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index e02729d..732371c 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -4573,6 +4573,7 @@ static void wlc_lcnphy_tbl_init(struct brcms_phy *pi)
uint idx;
u8 phybw40;
struct phytbl_info tab;
+ const struct phytbl_info *tb;
u32 val;
phybw40 = CHSPEC_IS40(pi->radio_chanspec);
@@ -4619,7 +4620,6 @@ static void wlc_lcnphy_tbl_init(struct brcms_phy *pi)
}
if (LCNREV_IS(pi->pubpi.phy_rev, 2)) {
- const struct phytbl_info *tb;
int l;
if (CHSPEC_IS2G(pi->radio_chanspec)) {
@@ -4640,21 +4640,22 @@ static void wlc_lcnphy_tbl_init(struct brcms_phy *pi)
wlc_lcnphy_write_table(pi, &tb[idx]);
}
- if ((pi->sh->boardflags & BFL_FEM)
- && !(pi->sh->boardflags & BFL_FEM_BT))
- wlc_lcnphy_write_table(pi, &dot11lcn_sw_ctrl_tbl_info_4313_epa);
- else if (pi->sh->boardflags & BFL_FEM_BT) {
- if (pi->sh->boardrev < 0x1250)
- wlc_lcnphy_write_table(
- pi,
- &dot11lcn_sw_ctrl_tbl_info_4313_bt_epa);
+ if (pi->sh->boardflags & BFL_FEM) {
+ if (pi->sh->boardflags & BFL_FEM_BT) {
+ if (pi->sh->boardrev < 0x1250)
+ tb = &dot11lcn_sw_ctrl_tbl_info_4313_bt_epa;
+ else
+ tb = &dot11lcn_sw_ctrl_tbl_info_4313_bt_epa_p250;
+ } else {
+ tb = &dot11lcn_sw_ctrl_tbl_info_4313_epa;
+ }
+ } else {
+ if (pi->sh->boardflags & BFL_FEM_BT)
+ tb = &dot11lcn_sw_ctrl_tbl_info_4313_bt_ipa;
else
- wlc_lcnphy_write_table(
- pi,
- &dot11lcn_sw_ctrl_tbl_info_4313_bt_epa_p250);
- } else
- wlc_lcnphy_write_table(pi, &dot11lcn_sw_ctrl_tbl_info_4313);
-
+ tb = &dot11lcn_sw_ctrl_tbl_info_4313;
+ }
+ wlc_lcnphy_write_table(pi, tb);
wlc_lcnphy_load_rfpower(pi);
wlc_lcnphy_clear_papd_comptable(pi);
--
1.7.10.4
When changing channels the TSSI based power control needs to be
reinitialized.
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index a0a268d..6e6bc28 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -5019,6 +5019,8 @@ void wlc_phy_chanspec_set_lcnphy(struct brcms_phy *pi, u16 chanspec)
wlc_lcnphy_load_tx_iir_filter(pi, true, 3);
mod_phy_reg(pi, 0x4eb, (0x7 << 3), (1) << 3);
+ if (wlc_lcnphy_tssi_based_pwr_ctrl_enabled(pi))
+ wlc_lcnphy_tssi_setup(pi);
}
void wlc_phy_detach_lcnphy(struct brcms_phy *pi)
--
1.7.10.4
Cleaning up some code fragments reducing indentation and uncluttering
some lines. Apart from whitespace there are no actual code changes
made.
Cc: Jonas Gorski <[email protected]>
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
.../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 213 ++++++++++----------
1 file changed, 106 insertions(+), 107 deletions(-)
diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index 3d6b16c..e646ba0 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -1137,8 +1137,9 @@ wlc_lcnphy_set_rx_gain_by_distribution(struct brcms_phy *pi,
gain0_15 = ((biq1 & 0xf) << 12) |
((tia & 0xf) << 8) |
((lna2 & 0x3) << 6) |
- ((lna2 &
- 0x3) << 4) | ((lna1 & 0x3) << 2) | ((lna1 & 0x3) << 0);
+ ((lna2 & 0x3) << 4) |
+ ((lna1 & 0x3) << 2) |
+ ((lna1 & 0x3) << 0);
mod_phy_reg(pi, 0x4b6, (0xffff << 0), gain0_15 << 0);
mod_phy_reg(pi, 0x4b7, (0xf << 0), gain16_19 << 0);
@@ -1368,126 +1369,124 @@ wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi,
goto cal_done;
}
- if (module == 1) {
+ WARN_ON(module != 1);
+ tx_pwr_ctrl = wlc_lcnphy_get_tx_pwr_ctrl(pi);
+ wlc_lcnphy_set_tx_pwr_ctrl(pi, LCNPHY_TX_PWR_CTRL_OFF);
- tx_pwr_ctrl = wlc_lcnphy_get_tx_pwr_ctrl(pi);
- wlc_lcnphy_set_tx_pwr_ctrl(pi, LCNPHY_TX_PWR_CTRL_OFF);
+ for (i = 0; i < 11; i++)
+ values_to_save[i] =
+ read_radio_reg(pi, rxiq_cal_rf_reg[i]);
+ Core1TxControl_old = read_phy_reg(pi, 0x631);
+
+ or_phy_reg(pi, 0x631, 0x0015);
+
+ RFOverride0_old = read_phy_reg(pi, 0x44c);
+ RFOverrideVal0_old = read_phy_reg(pi, 0x44d);
+ rfoverride2_old = read_phy_reg(pi, 0x4b0);
+ rfoverride2val_old = read_phy_reg(pi, 0x4b1);
+ rfoverride3_old = read_phy_reg(pi, 0x4f9);
+ rfoverride3val_old = read_phy_reg(pi, 0x4fa);
+ rfoverride4_old = read_phy_reg(pi, 0x938);
+ rfoverride4val_old = read_phy_reg(pi, 0x939);
+ afectrlovr_old = read_phy_reg(pi, 0x43b);
+ afectrlovrval_old = read_phy_reg(pi, 0x43c);
+ old_sslpnCalibClkEnCtrl = read_phy_reg(pi, 0x6da);
+ old_sslpnRxFeClkEnCtrl = read_phy_reg(pi, 0x6db);
- for (i = 0; i < 11; i++)
- values_to_save[i] =
- read_radio_reg(pi, rxiq_cal_rf_reg[i]);
- Core1TxControl_old = read_phy_reg(pi, 0x631);
-
- or_phy_reg(pi, 0x631, 0x0015);
-
- RFOverride0_old = read_phy_reg(pi, 0x44c);
- RFOverrideVal0_old = read_phy_reg(pi, 0x44d);
- rfoverride2_old = read_phy_reg(pi, 0x4b0);
- rfoverride2val_old = read_phy_reg(pi, 0x4b1);
- rfoverride3_old = read_phy_reg(pi, 0x4f9);
- rfoverride3val_old = read_phy_reg(pi, 0x4fa);
- rfoverride4_old = read_phy_reg(pi, 0x938);
- rfoverride4val_old = read_phy_reg(pi, 0x939);
- afectrlovr_old = read_phy_reg(pi, 0x43b);
- afectrlovrval_old = read_phy_reg(pi, 0x43c);
- old_sslpnCalibClkEnCtrl = read_phy_reg(pi, 0x6da);
- old_sslpnRxFeClkEnCtrl = read_phy_reg(pi, 0x6db);
-
- tx_gain_override_old = wlc_lcnphy_tx_gain_override_enabled(pi);
- if (tx_gain_override_old) {
- wlc_lcnphy_get_tx_gain(pi, &old_gains);
- tx_gain_index_old = pi_lcn->lcnphy_current_index;
- }
+ tx_gain_override_old = wlc_lcnphy_tx_gain_override_enabled(pi);
+ if (tx_gain_override_old) {
+ wlc_lcnphy_get_tx_gain(pi, &old_gains);
+ tx_gain_index_old = pi_lcn->lcnphy_current_index;
+ }
- wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_idx);
+ wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_idx);
- mod_phy_reg(pi, 0x4f9, (0x1 << 0), 1 << 0);
- mod_phy_reg(pi, 0x4fa, (0x1 << 0), 0 << 0);
+ mod_phy_reg(pi, 0x4f9, (0x1 << 0), 1 << 0);
+ mod_phy_reg(pi, 0x4fa, (0x1 << 0), 0 << 0);
- mod_phy_reg(pi, 0x43b, (0x1 << 1), 1 << 1);
- mod_phy_reg(pi, 0x43c, (0x1 << 1), 0 << 1);
+ mod_phy_reg(pi, 0x43b, (0x1 << 1), 1 << 1);
+ mod_phy_reg(pi, 0x43c, (0x1 << 1), 0 << 1);
- write_radio_reg(pi, RADIO_2064_REG116, 0x06);
- write_radio_reg(pi, RADIO_2064_REG12C, 0x07);
- write_radio_reg(pi, RADIO_2064_REG06A, 0xd3);
- write_radio_reg(pi, RADIO_2064_REG098, 0x03);
- write_radio_reg(pi, RADIO_2064_REG00B, 0x7);
- mod_radio_reg(pi, RADIO_2064_REG113, 1 << 4, 1 << 4);
- write_radio_reg(pi, RADIO_2064_REG01D, 0x01);
- write_radio_reg(pi, RADIO_2064_REG114, 0x01);
- write_radio_reg(pi, RADIO_2064_REG02E, 0x10);
- write_radio_reg(pi, RADIO_2064_REG12A, 0x08);
-
- mod_phy_reg(pi, 0x938, (0x1 << 0), 1 << 0);
- mod_phy_reg(pi, 0x939, (0x1 << 0), 0 << 0);
- mod_phy_reg(pi, 0x938, (0x1 << 1), 1 << 1);
- mod_phy_reg(pi, 0x939, (0x1 << 1), 1 << 1);
- mod_phy_reg(pi, 0x938, (0x1 << 2), 1 << 2);
- mod_phy_reg(pi, 0x939, (0x1 << 2), 1 << 2);
- mod_phy_reg(pi, 0x938, (0x1 << 3), 1 << 3);
- mod_phy_reg(pi, 0x939, (0x1 << 3), 1 << 3);
- mod_phy_reg(pi, 0x938, (0x1 << 5), 1 << 5);
- mod_phy_reg(pi, 0x939, (0x1 << 5), 0 << 5);
-
- mod_phy_reg(pi, 0x43b, (0x1 << 0), 1 << 0);
- mod_phy_reg(pi, 0x43c, (0x1 << 0), 0 << 0);
-
- wlc_lcnphy_start_tx_tone(pi, 2000, 120, 0);
- write_phy_reg(pi, 0x6da, 0xffff);
- or_phy_reg(pi, 0x6db, 0x3);
- wlc_lcnphy_set_trsw_override(pi, tx_switch, rx_switch);
- wlc_lcnphy_rx_gain_override_enable(pi, true);
-
- tia_gain = 8;
- rx_pwr_threshold = 950;
- while (tia_gain > 0) {
- tia_gain -= 1;
- wlc_lcnphy_set_rx_gain_by_distribution(pi,
- 0, 0, 2, 2,
- (u16)
- tia_gain, 1, 0);
- udelay(500);
+ write_radio_reg(pi, RADIO_2064_REG116, 0x06);
+ write_radio_reg(pi, RADIO_2064_REG12C, 0x07);
+ write_radio_reg(pi, RADIO_2064_REG06A, 0xd3);
+ write_radio_reg(pi, RADIO_2064_REG098, 0x03);
+ write_radio_reg(pi, RADIO_2064_REG00B, 0x7);
+ mod_radio_reg(pi, RADIO_2064_REG113, 1 << 4, 1 << 4);
+ write_radio_reg(pi, RADIO_2064_REG01D, 0x01);
+ write_radio_reg(pi, RADIO_2064_REG114, 0x01);
+ write_radio_reg(pi, RADIO_2064_REG02E, 0x10);
+ write_radio_reg(pi, RADIO_2064_REG12A, 0x08);
+
+ mod_phy_reg(pi, 0x938, (0x1 << 0), 1 << 0);
+ mod_phy_reg(pi, 0x939, (0x1 << 0), 0 << 0);
+ mod_phy_reg(pi, 0x938, (0x1 << 1), 1 << 1);
+ mod_phy_reg(pi, 0x939, (0x1 << 1), 1 << 1);
+ mod_phy_reg(pi, 0x938, (0x1 << 2), 1 << 2);
+ mod_phy_reg(pi, 0x939, (0x1 << 2), 1 << 2);
+ mod_phy_reg(pi, 0x938, (0x1 << 3), 1 << 3);
+ mod_phy_reg(pi, 0x939, (0x1 << 3), 1 << 3);
+ mod_phy_reg(pi, 0x938, (0x1 << 5), 1 << 5);
+ mod_phy_reg(pi, 0x939, (0x1 << 5), 0 << 5);
- received_power =
- wlc_lcnphy_measure_digital_power(pi, 2000);
- if (received_power < rx_pwr_threshold)
- break;
- }
- result = wlc_lcnphy_calc_rx_iq_comp(pi, 0xffff);
+ mod_phy_reg(pi, 0x43b, (0x1 << 0), 1 << 0);
+ mod_phy_reg(pi, 0x43c, (0x1 << 0), 0 << 0);
- wlc_lcnphy_stop_tx_tone(pi);
+ wlc_lcnphy_start_tx_tone(pi, 2000, 120, 0);
+ write_phy_reg(pi, 0x6da, 0xffff);
+ or_phy_reg(pi, 0x6db, 0x3);
+ wlc_lcnphy_set_trsw_override(pi, tx_switch, rx_switch);
+ wlc_lcnphy_rx_gain_override_enable(pi, true);
- write_phy_reg(pi, 0x631, Core1TxControl_old);
+ tia_gain = 8;
+ rx_pwr_threshold = 950;
+ while (tia_gain > 0) {
+ tia_gain -= 1;
+ wlc_lcnphy_set_rx_gain_by_distribution(pi,
+ 0, 0, 2, 2,
+ (u16)
+ tia_gain, 1, 0);
+ udelay(500);
- write_phy_reg(pi, 0x44c, RFOverrideVal0_old);
- write_phy_reg(pi, 0x44d, RFOverrideVal0_old);
- write_phy_reg(pi, 0x4b0, rfoverride2_old);
- write_phy_reg(pi, 0x4b1, rfoverride2val_old);
- write_phy_reg(pi, 0x4f9, rfoverride3_old);
- write_phy_reg(pi, 0x4fa, rfoverride3val_old);
- write_phy_reg(pi, 0x938, rfoverride4_old);
- write_phy_reg(pi, 0x939, rfoverride4val_old);
- write_phy_reg(pi, 0x43b, afectrlovr_old);
- write_phy_reg(pi, 0x43c, afectrlovrval_old);
- write_phy_reg(pi, 0x6da, old_sslpnCalibClkEnCtrl);
- write_phy_reg(pi, 0x6db, old_sslpnRxFeClkEnCtrl);
+ received_power =
+ wlc_lcnphy_measure_digital_power(pi, 2000);
+ if (received_power < rx_pwr_threshold)
+ break;
+ }
+ result = wlc_lcnphy_calc_rx_iq_comp(pi, 0xffff);
- wlc_lcnphy_clear_trsw_override(pi);
+ wlc_lcnphy_stop_tx_tone(pi);
- mod_phy_reg(pi, 0x44c, (0x1 << 2), 0 << 2);
+ write_phy_reg(pi, 0x631, Core1TxControl_old);
+
+ write_phy_reg(pi, 0x44c, RFOverrideVal0_old);
+ write_phy_reg(pi, 0x44d, RFOverrideVal0_old);
+ write_phy_reg(pi, 0x4b0, rfoverride2_old);
+ write_phy_reg(pi, 0x4b1, rfoverride2val_old);
+ write_phy_reg(pi, 0x4f9, rfoverride3_old);
+ write_phy_reg(pi, 0x4fa, rfoverride3val_old);
+ write_phy_reg(pi, 0x938, rfoverride4_old);
+ write_phy_reg(pi, 0x939, rfoverride4val_old);
+ write_phy_reg(pi, 0x43b, afectrlovr_old);
+ write_phy_reg(pi, 0x43c, afectrlovrval_old);
+ write_phy_reg(pi, 0x6da, old_sslpnCalibClkEnCtrl);
+ write_phy_reg(pi, 0x6db, old_sslpnRxFeClkEnCtrl);
- for (i = 0; i < 11; i++)
- write_radio_reg(pi, rxiq_cal_rf_reg[i],
- values_to_save[i]);
+ wlc_lcnphy_clear_trsw_override(pi);
- if (tx_gain_override_old)
- wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_index_old);
- else
- wlc_lcnphy_disable_tx_gain_override(pi);
+ mod_phy_reg(pi, 0x44c, (0x1 << 2), 0 << 2);
- wlc_lcnphy_set_tx_pwr_ctrl(pi, tx_pwr_ctrl);
- wlc_lcnphy_rx_gain_override_enable(pi, false);
- }
+ for (i = 0; i < 11; i++)
+ write_radio_reg(pi, rxiq_cal_rf_reg[i],
+ values_to_save[i]);
+
+ if (tx_gain_override_old)
+ wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_index_old);
+ else
+ wlc_lcnphy_disable_tx_gain_override(pi);
+
+ wlc_lcnphy_set_tx_pwr_ctrl(pi, tx_pwr_ctrl);
+ wlc_lcnphy_rx_gain_override_enable(pi, false);
cal_done:
kfree(ptr);
--
1.7.10.4
Hi
On Tue, Aug 13, 2013 at 10:03 PM, Arend van Spriel <[email protected]> wrote:
> This series replaces the patch "[PATCH 12/12] brcmsmac: support 4313iPA"
> with Message-ID: <[email protected]>.
>
> It has been split up into individual patches. Please test this series
> especially if you had issues with the original commit b6fc28a that was
> reverted.
>
> Cc: Jonas Gorski <[email protected]>
> Cc: David Herrmann <[email protected]>
> Cc: Maximilian Engelhardt <[email protected]>
> Cc: David Costa <[email protected]>
Is this available in a public branch that I can merge? And what should
be used as base? 3.11-rc5? linux-next?
Cheers
David
> Arend van Spriel (13):
> brcmsmac: cosmetic change in phy_lcn.c
> brcmsmac: change pa_gain for bcm4313 iPA
> brcmsmac: use ARRAY_SIZE in phytbl_lcn.c
> brcmsmac: add switch control table for BCM4313 iPA BT-combo cards
> brcmsmac: add debug info message providing phy and radio info
> brcmsmac: update transmit gain table for lcn phy
> brcmsmac: change lcnphy receive i/q calibration routine
> brcmsmac: fix TSSI idle estimation
> brcmsmac: avoid calling set_txpwr_by_index() twice
> brcmsmac: rework switch control table init including iPA BT-combo
> brcmsmac: correct phy registers for TSSI-based power control
> brcmsmac: reinitialize TSSI power control upon channel switch
> brcmsmac: add support for BCM4313 iPA variant
>
> drivers/net/wireless/brcm80211/brcmsmac/main.c | 4 +-
> .../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 397 +++++++++++--------
> .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c | 405 +++++++++++---------
> .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h | 1 +
> 4 files changed, 475 insertions(+), 332 deletions(-)
>
> --
> 1.7.10.4
>
>
This patch completes the changes needed for supporting the
iPA variant cards of the BCM4313 wireless chipset.
Cc: Jonas Gorski <[email protected]>
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
.../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 71 ++++++++++++++------
1 file changed, 51 insertions(+), 20 deletions(-)
diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index 6e6bc28..4ba5d62 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -1826,6 +1826,17 @@ wlc_lcnphy_radio_2064_channel_tune_4313(struct brcms_phy *pi, u8 channel)
write_radio_reg(pi, RADIO_2064_REG038, 3);
write_radio_reg(pi, RADIO_2064_REG091, 7);
}
+
+ if (!(pi->sh->boardflags & BFL_FEM)) {
+ u8 reg038[14] = {0xd, 0xe, 0xd, 0xd, 0xd, 0xc,
+ 0xa, 0xb, 0xb, 0x3, 0x3, 0x2, 0x0, 0x0};
+
+ write_radio_reg(pi, RADIO_2064_REG02A, 0xf);
+ write_radio_reg(pi, RADIO_2064_REG091, 0x3);
+ write_radio_reg(pi, RADIO_2064_REG038, 0x3);
+
+ write_radio_reg(pi, RADIO_2064_REG038, reg038[channel - 1]);
+ }
}
static int
@@ -2123,7 +2134,16 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi)
{
struct phytbl_info tab;
u32 rfseq, ind;
+ enum lcnphy_tssi_mode mode;
+ u8 tssi_sel;
+ if (pi->sh->boardflags & BFL_FEM) {
+ tssi_sel = 0x1;
+ mode = LCNPHY_TSSI_EXT;
+ } else {
+ tssi_sel = 0xe;
+ mode = LCNPHY_TSSI_POST_PA;
+ }
tab.tbl_id = LCNPHY_TBL_ID_TXPWRCTL;
tab.tbl_width = 32;
tab.tbl_ptr = &ind;
@@ -2144,7 +2164,7 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi)
mod_phy_reg(pi, 0x503, (0x1 << 4), (1) << 4);
- wlc_lcnphy_set_tssi_mux(pi, LCNPHY_TSSI_EXT);
+ wlc_lcnphy_set_tssi_mux(pi, mode);
mod_phy_reg(pi, 0x4a4, (0x1 << 14), (0) << 14);
mod_phy_reg(pi, 0x4a4, (0x1 << 15), (1) << 15);
@@ -2180,9 +2200,10 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi)
mod_phy_reg(pi, 0x49a, (0x1ff << 0), (0xff) << 0);
if (LCNREV_IS(pi->pubpi.phy_rev, 2)) {
- mod_radio_reg(pi, RADIO_2064_REG028, 0xf, 0xe);
+ mod_radio_reg(pi, RADIO_2064_REG028, 0xf, tssi_sel);
mod_radio_reg(pi, RADIO_2064_REG086, 0x4, 0x4);
} else {
+ mod_radio_reg(pi, RADIO_2064_REG028, 0x1e, tssi_sel << 1);
mod_radio_reg(pi, RADIO_2064_REG03A, 0x1, 1);
mod_radio_reg(pi, RADIO_2064_REG11A, 0x8, 1 << 3);
}
@@ -4358,8 +4379,11 @@ wlc_lcnphy_load_tx_gain_table(struct brcms_phy *pi,
tab.tbl_len = 1;
tab.tbl_ptr = &val;
+ /* fixed gm_gain value for iPA */
+ gm_gain = 15;
for (j = 0; j < 128; j++) {
- gm_gain = gain_table[j].gm;
+ if (pi->sh->boardflags & BFL_FEM)
+ gm_gain = gain_table[j].gm;
val = (((u32) pa_gain << 24) |
(gain_table[j].pad << 16) |
(gain_table[j].pga << 8) | gm_gain);
@@ -4570,7 +4594,10 @@ static void wlc_radio_2064_init(struct brcms_phy *pi)
write_phy_reg(pi, 0x4ea, 0x4688);
- mod_phy_reg(pi, 0x4eb, (0x7 << 0), 2 << 0);
+ if (pi->sh->boardflags & BFL_FEM)
+ mod_phy_reg(pi, 0x4eb, (0x7 << 0), 2 << 0);
+ else
+ mod_phy_reg(pi, 0x4eb, (0x7 << 0), 3 << 0);
mod_phy_reg(pi, 0x4eb, (0x7 << 6), 0 << 6);
@@ -4581,6 +4608,13 @@ static void wlc_radio_2064_init(struct brcms_phy *pi)
wlc_lcnphy_rcal(pi);
wlc_lcnphy_rc_cal(pi);
+
+ if (!(pi->sh->boardflags & BFL_FEM)) {
+ write_radio_reg(pi, RADIO_2064_REG032, 0x6f);
+ write_radio_reg(pi, RADIO_2064_REG033, 0x19);
+ write_radio_reg(pi, RADIO_2064_REG039, 0xe);
+ }
+
}
static void wlc_lcnphy_radio_init(struct brcms_phy *pi)
@@ -4611,22 +4645,20 @@ static void wlc_lcnphy_tbl_init(struct brcms_phy *pi)
wlc_lcnphy_write_table(pi, &tab);
}
- tab.tbl_id = LCNPHY_TBL_ID_RFSEQ;
- tab.tbl_width = 16;
- tab.tbl_ptr = &val;
- tab.tbl_len = 1;
-
- val = 114;
- tab.tbl_offset = 0;
- wlc_lcnphy_write_table(pi, &tab);
+ if (!(pi->sh->boardflags & BFL_FEM)) {
+ tab.tbl_id = LCNPHY_TBL_ID_RFSEQ;
+ tab.tbl_width = 16;
+ tab.tbl_ptr = &val;
+ tab.tbl_len = 1;
- val = 130;
- tab.tbl_offset = 1;
- wlc_lcnphy_write_table(pi, &tab);
+ val = 150;
+ tab.tbl_offset = 0;
+ wlc_lcnphy_write_table(pi, &tab);
- val = 6;
- tab.tbl_offset = 8;
- wlc_lcnphy_write_table(pi, &tab);
+ val = 220;
+ tab.tbl_offset = 1;
+ wlc_lcnphy_write_table(pi, &tab);
+ }
if (CHSPEC_IS2G(pi->radio_chanspec)) {
if (pi->sh->boardflags & BFL_FEM)
@@ -5059,8 +5091,7 @@ bool wlc_phy_attach_lcnphy(struct brcms_phy *pi)
if (!wlc_phy_txpwr_srom_read_lcnphy(pi))
return false;
- if ((pi->sh->boardflags & BFL_FEM) &&
- (LCNREV_IS(pi->pubpi.phy_rev, 1))) {
+ if (LCNREV_IS(pi->pubpi.phy_rev, 1)) {
if (pi_lcn->lcnphy_tempsense_option == 3) {
pi->hwpwrctrl = true;
pi->hwpwrctrl_capable = true;
--
1.7.10.4
Update the transmit gain table for bcm4313 chip family.
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
.../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c | 216 ++++++++++----------
1 file changed, 108 insertions(+), 108 deletions(-)
diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
index 36c41df..d7fa312 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
@@ -3031,134 +3031,134 @@ dot11lcnphy_2GHz_extPA_gaintable_rev0[128] = {
};
const struct lcnphy_tx_gain_tbl_entry dot11lcnphy_2GHz_gaintable_rev0[128] = {
- {7, 0, 31, 0, 72},
- {7, 0, 31, 0, 70},
- {7, 0, 31, 0, 68},
- {7, 0, 30, 0, 67},
- {7, 0, 29, 0, 68},
- {7, 0, 28, 0, 68},
- {7, 0, 27, 0, 69},
- {7, 0, 26, 0, 70},
- {7, 0, 25, 0, 70},
- {7, 0, 24, 0, 71},
- {7, 0, 23, 0, 72},
- {7, 0, 23, 0, 70},
- {7, 0, 22, 0, 71},
- {7, 0, 21, 0, 72},
- {7, 0, 21, 0, 70},
- {7, 0, 21, 0, 68},
- {7, 0, 21, 0, 66},
- {7, 0, 21, 0, 64},
- {7, 0, 21, 0, 63},
- {7, 0, 20, 0, 64},
- {7, 0, 19, 0, 65},
- {7, 0, 19, 0, 64},
- {7, 0, 18, 0, 65},
- {7, 0, 18, 0, 64},
- {7, 0, 17, 0, 65},
- {7, 0, 17, 0, 64},
- {7, 0, 16, 0, 65},
- {7, 0, 16, 0, 64},
- {7, 0, 16, 0, 62},
- {7, 0, 16, 0, 60},
- {7, 0, 16, 0, 58},
- {7, 0, 15, 0, 61},
- {7, 0, 15, 0, 59},
- {7, 0, 14, 0, 61},
- {7, 0, 14, 0, 60},
- {7, 0, 14, 0, 58},
- {7, 0, 13, 0, 60},
- {7, 0, 13, 0, 59},
- {7, 0, 12, 0, 62},
- {7, 0, 12, 0, 60},
- {7, 0, 12, 0, 58},
- {7, 0, 11, 0, 62},
- {7, 0, 11, 0, 60},
- {7, 0, 11, 0, 59},
- {7, 0, 11, 0, 57},
- {7, 0, 10, 0, 61},
- {7, 0, 10, 0, 59},
- {7, 0, 10, 0, 57},
- {7, 0, 9, 0, 62},
- {7, 0, 9, 0, 60},
- {7, 0, 9, 0, 58},
- {7, 0, 9, 0, 57},
- {7, 0, 8, 0, 62},
- {7, 0, 8, 0, 60},
- {7, 0, 8, 0, 58},
- {7, 0, 8, 0, 57},
- {7, 0, 8, 0, 55},
- {7, 0, 7, 0, 61},
+ {15, 0, 31, 0, 72},
+ {15, 0, 31, 0, 70},
+ {15, 0, 31, 0, 68},
+ {15, 0, 30, 0, 68},
+ {15, 0, 29, 0, 69},
+ {15, 0, 28, 0, 69},
+ {15, 0, 27, 0, 70},
+ {15, 0, 26, 0, 70},
+ {15, 0, 25, 0, 71},
+ {15, 0, 24, 0, 72},
+ {15, 0, 23, 0, 73},
+ {15, 0, 23, 0, 71},
+ {15, 0, 22, 0, 72},
+ {15, 0, 21, 0, 73},
+ {15, 0, 21, 0, 71},
+ {15, 0, 21, 0, 69},
+ {15, 0, 21, 0, 67},
+ {15, 0, 21, 0, 65},
+ {15, 0, 21, 0, 63},
+ {15, 0, 20, 0, 65},
+ {15, 0, 19, 0, 66},
+ {15, 0, 19, 0, 64},
+ {15, 0, 18, 0, 66},
+ {15, 0, 18, 0, 64},
+ {15, 0, 17, 0, 66},
+ {15, 0, 17, 0, 64},
+ {15, 0, 16, 0, 66},
+ {15, 0, 16, 0, 64},
+ {15, 0, 16, 0, 62},
+ {15, 0, 16, 0, 61},
+ {15, 0, 16, 0, 59},
+ {15, 0, 15, 0, 61},
+ {15, 0, 15, 0, 59},
+ {15, 0, 14, 0, 62},
+ {15, 0, 14, 0, 60},
+ {15, 0, 14, 0, 58},
+ {15, 0, 13, 0, 61},
+ {15, 0, 13, 0, 59},
+ {15, 0, 12, 0, 62},
+ {15, 0, 12, 0, 61},
+ {15, 0, 12, 0, 59},
+ {15, 0, 11, 0, 62},
+ {15, 0, 11, 0, 61},
+ {15, 0, 11, 0, 59},
+ {15, 0, 11, 0, 57},
+ {15, 0, 10, 0, 61},
+ {15, 0, 10, 0, 59},
+ {15, 0, 10, 0, 58},
+ {15, 0, 9, 0, 62},
+ {15, 0, 9, 0, 61},
+ {15, 0, 9, 0, 59},
+ {15, 0, 9, 0, 57},
+ {15, 0, 8, 0, 62},
+ {15, 0, 8, 0, 61},
+ {15, 0, 8, 0, 59},
+ {15, 0, 8, 0, 57},
+ {15, 0, 8, 0, 56},
+ {15, 0, 8, 0, 54},
+ {15, 0, 8, 0, 53},
+ {15, 0, 8, 0, 51},
+ {15, 0, 8, 0, 50},
+ {7, 0, 7, 0, 69},
+ {7, 0, 7, 0, 67},
+ {7, 0, 7, 0, 65},
+ {7, 0, 7, 0, 64},
+ {7, 0, 7, 0, 62},
{7, 0, 7, 0, 60},
{7, 0, 7, 0, 58},
- {7, 0, 7, 0, 56},
+ {7, 0, 7, 0, 57},
{7, 0, 7, 0, 55},
{7, 0, 6, 0, 62},
- {7, 0, 6, 0, 60},
- {7, 0, 6, 0, 58},
+ {7, 0, 6, 0, 61},
+ {7, 0, 6, 0, 59},
{7, 0, 6, 0, 57},
- {7, 0, 6, 0, 55},
+ {7, 0, 6, 0, 56},
{7, 0, 6, 0, 54},
- {7, 0, 6, 0, 52},
+ {7, 0, 6, 0, 53},
{7, 0, 5, 0, 61},
- {7, 0, 5, 0, 59},
- {7, 0, 5, 0, 57},
+ {7, 0, 5, 0, 60},
+ {7, 0, 5, 0, 58},
{7, 0, 5, 0, 56},
- {7, 0, 5, 0, 54},
+ {7, 0, 5, 0, 55},
{7, 0, 5, 0, 53},
- {7, 0, 5, 0, 51},
- {7, 0, 4, 0, 62},
- {7, 0, 4, 0, 60},
- {7, 0, 4, 0, 58},
+ {7, 0, 5, 0, 52},
+ {7, 0, 5, 0, 50},
+ {7, 0, 5, 0, 49},
+ {7, 0, 5, 0, 47},
{7, 0, 4, 0, 57},
- {7, 0, 4, 0, 55},
+ {7, 0, 4, 0, 56},
{7, 0, 4, 0, 54},
- {7, 0, 4, 0, 52},
+ {7, 0, 4, 0, 53},
{7, 0, 4, 0, 51},
- {7, 0, 4, 0, 49},
+ {7, 0, 4, 0, 50},
{7, 0, 4, 0, 48},
+ {7, 0, 4, 0, 47},
{7, 0, 4, 0, 46},
- {7, 0, 3, 0, 60},
- {7, 0, 3, 0, 58},
- {7, 0, 3, 0, 57},
- {7, 0, 3, 0, 55},
- {7, 0, 3, 0, 54},
- {7, 0, 3, 0, 52},
+ {7, 0, 4, 0, 44},
+ {7, 0, 4, 0, 43},
+ {7, 0, 4, 0, 42},
+ {7, 0, 4, 0, 41},
+ {7, 0, 4, 0, 40},
{7, 0, 3, 0, 51},
- {7, 0, 3, 0, 49},
+ {7, 0, 3, 0, 50},
{7, 0, 3, 0, 48},
+ {7, 0, 3, 0, 47},
{7, 0, 3, 0, 46},
- {7, 0, 3, 0, 45},
{7, 0, 3, 0, 44},
{7, 0, 3, 0, 43},
+ {7, 0, 3, 0, 42},
{7, 0, 3, 0, 41},
- {7, 0, 2, 0, 61},
- {7, 0, 2, 0, 59},
- {7, 0, 2, 0, 57},
- {7, 0, 2, 0, 56},
- {7, 0, 2, 0, 54},
- {7, 0, 2, 0, 53},
- {7, 0, 2, 0, 51},
- {7, 0, 2, 0, 50},
- {7, 0, 2, 0, 48},
- {7, 0, 2, 0, 47},
- {7, 0, 2, 0, 46},
- {7, 0, 2, 0, 44},
- {7, 0, 2, 0, 43},
- {7, 0, 2, 0, 42},
- {7, 0, 2, 0, 41},
- {7, 0, 2, 0, 39},
- {7, 0, 2, 0, 38},
- {7, 0, 2, 0, 37},
- {7, 0, 2, 0, 36},
- {7, 0, 2, 0, 35},
- {7, 0, 2, 0, 34},
- {7, 0, 2, 0, 33},
- {7, 0, 2, 0, 32},
- {7, 0, 1, 0, 63},
- {7, 0, 1, 0, 61},
- {7, 0, 1, 0, 59},
- {7, 0, 1, 0, 57},
+ {3, 0, 3, 0, 56},
+ {3, 0, 3, 0, 54},
+ {3, 0, 3, 0, 53},
+ {3, 0, 3, 0, 51},
+ {3, 0, 3, 0, 50},
+ {3, 0, 3, 0, 48},
+ {3, 0, 3, 0, 47},
+ {3, 0, 3, 0, 46},
+ {3, 0, 3, 0, 44},
+ {3, 0, 3, 0, 43},
+ {3, 0, 3, 0, 42},
+ {3, 0, 3, 0, 41},
+ {3, 0, 3, 0, 39},
+ {3, 0, 3, 0, 38},
+ {3, 0, 3, 0, 37},
+ {3, 0, 3, 0, 36},
+ {3, 0, 3, 0, 35},
+ {3, 0, 3, 0, 34},
};
const struct lcnphy_tx_gain_tbl_entry dot11lcnphy_5GHz_gaintable_rev0[128] = {
--
1.7.10.4
On 08/21/2013 09:18 PM, Hauke Mehrtens wrote:
> Hi Arend,
>
> when you send a new patch please fix this typo.
Got it covered already:
http://mid.gmane.org/[email protected]
Regards,
Arend
> Hauke
>
> On 08/13/2013 10:03 PM, Arend van Spriel wrote:
>> The function wlc_lcnphy_load_tx_gain_table() has a target PA
>> gain specified for the iPA variant of the bcm4313. This gain
>> value is reduced to avoid PA distortion. The if-statement is
>> removed because it was rather redundant in the first place.
>> Please not that this patch does not provide full iPA support.
> ^^^
> note
>
>
>
The baseband multiplier must be zero during TSSI idle estimation
and restored afterwards.
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index 8099d74..96be1ba 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -2836,6 +2836,8 @@ static void wlc_lcnphy_idle_tssi_est(struct brcms_phy_pub *ppi)
read_radio_reg(pi, RADIO_2064_REG007) & 1;
u16 SAVE_jtag_auxpga = read_radio_reg(pi, RADIO_2064_REG0FF) & 0x10;
u16 SAVE_iqadc_aux_en = read_radio_reg(pi, RADIO_2064_REG11F) & 4;
+ u8 SAVE_bbmult = wlc_lcnphy_get_bbmult(pi);
+
idleTssi = read_phy_reg(pi, 0x4ab);
suspend = (0 == (bcma_read32(pi->d11core, D11REGOFFS(maccontrol)) &
MCTL_EN_MAC));
@@ -2853,6 +2855,12 @@ static void wlc_lcnphy_idle_tssi_est(struct brcms_phy_pub *ppi)
mod_radio_reg(pi, RADIO_2064_REG0FF, 0x10, 1 << 4);
mod_radio_reg(pi, RADIO_2064_REG11F, 0x4, 1 << 2);
wlc_lcnphy_tssi_setup(pi);
+
+ mod_phy_reg(pi, 0x4d7, (0x1 << 0), (1 << 0));
+ mod_phy_reg(pi, 0x4d7, (0x1 << 6), (1 << 6));
+
+ wlc_lcnphy_set_bbmult(pi, 0x0);
+
wlc_phy_do_dummy_tx(pi, true, OFF);
idleTssi = ((read_phy_reg(pi, 0x4ab) & (0x1ff << 0))
>> 0);
@@ -2874,6 +2882,7 @@ static void wlc_lcnphy_idle_tssi_est(struct brcms_phy_pub *ppi)
mod_phy_reg(pi, 0x44c, (0x1 << 12), (0) << 12);
+ wlc_lcnphy_set_bbmult(pi, SAVE_bbmult);
wlc_lcnphy_set_tx_gain_override(pi, tx_gain_override_old);
wlc_lcnphy_set_tx_gain(pi, &old_gains);
wlc_lcnphy_set_tx_pwr_ctrl(pi, SAVE_txpwrctrl);
--
1.7.10.4
A number of additional phy registers needs to be programmed when
using TSSI-based power control.
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
.../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index 732371c..a0a268d 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -2020,6 +2020,16 @@ wlc_lcnphy_set_tssi_mux(struct brcms_phy *pi, enum lcnphy_tssi_mode pos)
} else {
mod_radio_reg(pi, RADIO_2064_REG03A, 1, 0x1);
mod_radio_reg(pi, RADIO_2064_REG11A, 0x8, 0x8);
+ mod_radio_reg(pi, RADIO_2064_REG028, 0x1, 0x0);
+ mod_radio_reg(pi, RADIO_2064_REG11A, 0x4, 1<<2);
+ mod_radio_reg(pi, RADIO_2064_REG036, 0x10, 0x0);
+ mod_radio_reg(pi, RADIO_2064_REG11A, 0x10, 1<<4);
+ mod_radio_reg(pi, RADIO_2064_REG036, 0x3, 0x0);
+ mod_radio_reg(pi, RADIO_2064_REG035, 0xff, 0x77);
+ mod_radio_reg(pi, RADIO_2064_REG028, 0x1e, 0xe<<1);
+ mod_radio_reg(pi, RADIO_2064_REG112, 0x80, 1<<7);
+ mod_radio_reg(pi, RADIO_2064_REG005, 0x7, 1<<1);
+ mod_radio_reg(pi, RADIO_2064_REG029, 0xf0, 0<<4);
}
} else {
mod_phy_reg(pi, 0x4d9, (0x1 << 2), (0x1) << 2);
@@ -2106,6 +2116,7 @@ static void wlc_lcnphy_pwrctrl_rssiparams(struct brcms_phy *pi)
(auxpga_vmid_temp << 0) | (auxpga_gain_temp << 12));
mod_radio_reg(pi, RADIO_2064_REG082, (1 << 5), (1 << 5));
+ mod_radio_reg(pi, RADIO_2064_REG07C, (1 << 0), (1 << 0));
}
static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi)
@@ -2218,6 +2229,10 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi)
mod_phy_reg(pi, 0x4d7, (0xf << 8), (0) << 8);
+ mod_radio_reg(pi, RADIO_2064_REG035, 0xff, 0x0);
+ mod_radio_reg(pi, RADIO_2064_REG036, 0x3, 0x0);
+ mod_radio_reg(pi, RADIO_2064_REG11A, 0x8, 0x8);
+
wlc_lcnphy_pwrctrl_rssiparams(pi);
}
@@ -3096,6 +3111,11 @@ static void wlc_lcnphy_tx_pwr_ctrl_init(struct brcms_phy_pub *ppi)
wlc_lcnphy_write_table(pi, &tab);
tab.tbl_offset++;
}
+ mod_phy_reg(pi, 0x4d0, (0x1 << 0), (0) << 0);
+ mod_phy_reg(pi, 0x4d3, (0xff << 0), (0) << 0);
+ mod_phy_reg(pi, 0x4d3, (0xff << 8), (0) << 8);
+ mod_phy_reg(pi, 0x4d0, (0x1 << 4), (0) << 4);
+ mod_phy_reg(pi, 0x4d0, (0x1 << 2), (0) << 2);
mod_phy_reg(pi, 0x410, (0x1 << 7), (0) << 7);
--
1.7.10.4
On 08/21/13 18:17, Maximilian Engelhardt wrote:
> On Tuesday 13 August 2013 22:03:27 Arend van Spriel wrote:
>> This series replaces the patch "[PATCH 12/12] brcmsmac: support 4313iPA"
>> with Message-ID:<[email protected]>.
>>
>> It has been split up into individual patches. Please test this series
>> especially if you had issues with the original commit b6fc28a that was
>> reverted.
>>
>> Cc: Jonas Gorski<[email protected]>
>> Cc: David Herrmann<[email protected]>
>> Cc: Maximilian Engelhardt<[email protected]>
>> Cc: David Costa<[email protected]>
>>
>> Arend van Spriel (13):
>> brcmsmac: cosmetic change in phy_lcn.c
>> brcmsmac: change pa_gain for bcm4313 iPA
>> brcmsmac: use ARRAY_SIZE in phytbl_lcn.c
>> brcmsmac: add switch control table for BCM4313 iPA BT-combo cards
>> brcmsmac: add debug info message providing phy and radio info
>> brcmsmac: update transmit gain table for lcn phy
>> brcmsmac: change lcnphy receive i/q calibration routine
>> brcmsmac: fix TSSI idle estimation
>> brcmsmac: avoid calling set_txpwr_by_index() twice
>> brcmsmac: rework switch control table init including iPA BT-combo
>> brcmsmac: correct phy registers for TSSI-based power control
>> brcmsmac: reinitialize TSSI power control upon channel switch
>> brcmsmac: add support for BCM4313 iPA variant
>>
>> drivers/net/wireless/brcm80211/brcmsmac/main.c | 4 +-
>> .../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 397
>> +++++++++++-------- .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c |
>> 405 +++++++++++--------- .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h
>> | 1 +
>> 4 files changed, 475 insertions(+), 332 deletions(-)
>
> Hello Arend,
>
> I finally had some time to test your patches.
>
> On my hardware I couldn't find any regressions with these patches. I also
> verified that the reception problems I had with my card are fixed by these
> patches.
>
> I did test the patches on top of 3.10.5 as they did apply without any
> problems.
Appreciated. I did send the patches for wireless-next already, ie. for
v3.12 kernel. Good to know that they apply to 3.10 as is.
Regards,
Arend
Hi Arend,
when you send a new patch please fix this typo.
Hauke
On 08/13/2013 10:03 PM, Arend van Spriel wrote:
> The function wlc_lcnphy_load_tx_gain_table() has a target PA
> gain specified for the iPA variant of the bcm4313. This gain
> value is reduced to avoid PA distortion. The if-statement is
> removed because it was rather redundant in the first place.
> Please not that this patch does not provide full iPA support.
^^^
note
The gain setting for the test tone of the i/q calibration is
controlled has changed. This gain level needs to be set correctly
before the i/q compensation can be determined.
Cc: Jonas Gorski <[email protected]>
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Reviewed-by: Hante Meuleman <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
.../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 78 +++++++++++++++-----
1 file changed, 58 insertions(+), 20 deletions(-)
diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index 8dc5d0f..8099d74 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -1329,6 +1329,43 @@ static u32 wlc_lcnphy_measure_digital_power(struct brcms_phy *pi, u16 nsamples)
return (iq_est.i_pwr + iq_est.q_pwr) / nsamples;
}
+static bool wlc_lcnphy_rx_iq_cal_gain(struct brcms_phy *pi, u16 biq1_gain,
+ u16 tia_gain, u16 lna2_gain)
+{
+ u32 i_thresh_l, q_thresh_l;
+ u32 i_thresh_h, q_thresh_h;
+ struct lcnphy_iq_est iq_est_h, iq_est_l;
+
+ wlc_lcnphy_set_rx_gain_by_distribution(pi, 0, 0, 0, biq1_gain, tia_gain,
+ lna2_gain, 0);
+
+ wlc_lcnphy_rx_gain_override_enable(pi, true);
+ wlc_lcnphy_start_tx_tone(pi, 2000, (40 >> 1), 0);
+ udelay(500);
+ write_radio_reg(pi, RADIO_2064_REG112, 0);
+ if (!wlc_lcnphy_rx_iq_est(pi, 1024, 32, &iq_est_l))
+ return false;
+
+ wlc_lcnphy_start_tx_tone(pi, 2000, 40, 0);
+ udelay(500);
+ write_radio_reg(pi, RADIO_2064_REG112, 0);
+ if (!wlc_lcnphy_rx_iq_est(pi, 1024, 32, &iq_est_h))
+ return false;
+
+ i_thresh_l = (iq_est_l.i_pwr << 1);
+ i_thresh_h = (iq_est_l.i_pwr << 2) + iq_est_l.i_pwr;
+
+ q_thresh_l = (iq_est_l.q_pwr << 1);
+ q_thresh_h = (iq_est_l.q_pwr << 2) + iq_est_l.q_pwr;
+ if ((iq_est_h.i_pwr > i_thresh_l) &&
+ (iq_est_h.i_pwr < i_thresh_h) &&
+ (iq_est_h.q_pwr > q_thresh_l) &&
+ (iq_est_h.q_pwr < q_thresh_h))
+ return true;
+
+ return false;
+}
+
static bool
wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi,
const struct lcnphy_rx_iqcomp *iqcomp,
@@ -1343,8 +1380,8 @@ wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi,
RFOverrideVal0_old, rfoverride2_old, rfoverride2val_old,
rfoverride3_old, rfoverride3val_old, rfoverride4_old,
rfoverride4val_old, afectrlovr_old, afectrlovrval_old;
- int tia_gain;
- u32 received_power, rx_pwr_threshold;
+ int tia_gain, lna2_gain, biq1_gain;
+ bool set_gain;
u16 old_sslpnCalibClkEnCtrl, old_sslpnRxFeClkEnCtrl;
u16 values_to_save[11];
s16 *ptr;
@@ -1432,29 +1469,30 @@ wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi,
mod_phy_reg(pi, 0x43b, (0x1 << 0), 1 << 0);
mod_phy_reg(pi, 0x43c, (0x1 << 0), 0 << 0);
- wlc_lcnphy_start_tx_tone(pi, 2000, 120, 0);
write_phy_reg(pi, 0x6da, 0xffff);
or_phy_reg(pi, 0x6db, 0x3);
- wlc_lcnphy_set_trsw_override(pi, tx_switch, rx_switch);
- wlc_lcnphy_rx_gain_override_enable(pi, true);
-
- tia_gain = 8;
- rx_pwr_threshold = 950;
- while (tia_gain > 0) {
- tia_gain -= 1;
- wlc_lcnphy_set_rx_gain_by_distribution(pi,
- 0, 0, 2, 2,
- (u16)
- tia_gain, 1, 0);
- udelay(500);
- received_power =
- wlc_lcnphy_measure_digital_power(pi, 2000);
- if (received_power < rx_pwr_threshold)
- break;
+ wlc_lcnphy_set_trsw_override(pi, tx_switch, rx_switch);
+ for (lna2_gain = 3; lna2_gain >= 0; lna2_gain--) {
+ for (tia_gain = 4; tia_gain >= 0; tia_gain--) {
+ for (biq1_gain = 6; biq1_gain >= 0; biq1_gain--) {
+ set_gain = wlc_lcnphy_rx_iq_cal_gain(pi,
+ (u16)
+ biq1_gain,
+ (u16)
+ tia_gain,
+ (u16)
+ lna2_gain);
+ if (set_gain) {
+ result = wlc_lcnphy_calc_rx_iq_comp(pi,
+ 1024);
+ goto stop_tone;
+ }
+ }
+ }
}
- result = wlc_lcnphy_calc_rx_iq_comp(pi, 0xffff);
+stop_tone:
wlc_lcnphy_stop_tx_tone(pi);
write_phy_reg(pi, 0x631, Core1TxControl_old);
--
1.7.10.4
For lcnphy revision 1 or when hardware supports i/q calibration the
function wlc_lcnphy_set_txpwr_by_index() was called twice.
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index 96be1ba..e02729d 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -3897,7 +3897,6 @@ static void wlc_lcnphy_txpwrtbl_iqlo_cal(struct brcms_phy *pi)
target_gains.pad_gain = 21;
target_gains.dac_gain = 0;
wlc_lcnphy_set_tx_gain(pi, &target_gains);
- wlc_lcnphy_set_tx_pwr_by_index(pi, 16);
if (LCNREV_IS(pi->pubpi.phy_rev, 1) || pi_lcn->lcnphy_hw_iqcal_en) {
@@ -3908,6 +3907,7 @@ static void wlc_lcnphy_txpwrtbl_iqlo_cal(struct brcms_phy *pi)
lcnphy_recal ? LCNPHY_CAL_RECAL :
LCNPHY_CAL_FULL), false);
} else {
+ wlc_lcnphy_set_tx_pwr_by_index(pi, 16);
wlc_lcnphy_tx_iqlo_soft_cal_full(pi);
}
--
1.7.10.4
On 08/13/2013 10:09 PM, David Herrmann wrote:
> Hi
>
> On Tue, Aug 13, 2013 at 10:03 PM, Arend van Spriel <[email protected]> wrote:
>> This series replaces the patch "[PATCH 12/12] brcmsmac: support 4313iPA"
>> with Message-ID: <[email protected]>.
>>
>> It has been split up into individual patches. Please test this series
>> especially if you had issues with the original commit b6fc28a that was
>> reverted.
>>
>> Cc: Jonas Gorski <[email protected]>
>> Cc: David Herrmann <[email protected]>
>> Cc: Maximilian Engelhardt <[email protected]>
>> Cc: David Costa <[email protected]>
>
> Is this available in a public branch that I can merge? And what should
> be used as base? 3.11-rc5? linux-next?
Indeed I should have mentioned. It applies on v3.11-rc5 for sure. Did
not try linux-next.
Regards,
Arend
> Cheers
> David
>
>> Arend van Spriel (13):
>> brcmsmac: cosmetic change in phy_lcn.c
>> brcmsmac: change pa_gain for bcm4313 iPA
>> brcmsmac: use ARRAY_SIZE in phytbl_lcn.c
>> brcmsmac: add switch control table for BCM4313 iPA BT-combo cards
>> brcmsmac: add debug info message providing phy and radio info
>> brcmsmac: update transmit gain table for lcn phy
>> brcmsmac: change lcnphy receive i/q calibration routine
>> brcmsmac: fix TSSI idle estimation
>> brcmsmac: avoid calling set_txpwr_by_index() twice
>> brcmsmac: rework switch control table init including iPA BT-combo
>> brcmsmac: correct phy registers for TSSI-based power control
>> brcmsmac: reinitialize TSSI power control upon channel switch
>> brcmsmac: add support for BCM4313 iPA variant
>>
>> drivers/net/wireless/brcm80211/brcmsmac/main.c | 4 +-
>> .../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 397 +++++++++++--------
>> .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c | 405 +++++++++++---------
>> .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h | 1 +
>> 4 files changed, 475 insertions(+), 332 deletions(-)
>>
>> --
>> 1.7.10.4
>>
>>
>
For debug purposes it is good to have the phy and radio information
available in the log. Only logged when driver is build when BRCMDBG
or BRCM_TRACING kconfig are set.
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
drivers/net/wireless/brcm80211/brcmsmac/main.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/net/wireless/brcm80211/brcmsmac/main.c b/drivers/net/wireless/brcm80211/brcmsmac/main.c
index 7ca10bf..c3c6123 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/main.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/main.c
@@ -4652,7 +4652,9 @@ static int brcms_b_attach(struct brcms_c_info *wlc, struct bcma_device *core,
wlc->band->phyrev = wlc_hw->band->phyrev;
wlc->band->radioid = wlc_hw->band->radioid;
wlc->band->radiorev = wlc_hw->band->radiorev;
-
+ brcms_dbg_info(core, "wl%d: phy %u/%u radio %x/%u\n", unit,
+ wlc->band->phytype, wlc->band->phyrev,
+ wlc->band->radioid, wlc->band->radiorev);
/* default contention windows size limits */
wlc_hw->band->CWmin = APHY_CWMIN;
wlc_hw->band->CWmax = PHY_CWMAX;
--
1.7.10.4
This patch converts all sizeof(x)/sizeof(x[0]) instances to
ARRAY_SIZE macro in phytbl_lcn.c. The patch was made using
spatch with ARRAY_SIZE.cocci (see [1]).
[1] https://github.com/coccinelle/coccinelle/tree/master/demos/janitorings
Cc: Jonas Gorski <[email protected]>
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Hante Meuleman <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
.../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c | 117 ++++++++------------
1 file changed, 44 insertions(+), 73 deletions(-)
diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
index 622c01c..deae3a7 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
@@ -1507,117 +1507,103 @@ static const u32 dot11lcn_gain_tbl_5G[] = {
const struct phytbl_info dot11lcnphytbl_rx_gain_info_rev0[] = {
{&dot11lcn_gain_tbl_rev0,
- sizeof(dot11lcn_gain_tbl_rev0) / sizeof(dot11lcn_gain_tbl_rev0[0]), 18,
+ ARRAY_SIZE(dot11lcn_gain_tbl_rev0), 18,
0, 32}
,
{&dot11lcn_aux_gain_idx_tbl_rev0,
- sizeof(dot11lcn_aux_gain_idx_tbl_rev0) /
- sizeof(dot11lcn_aux_gain_idx_tbl_rev0[0]), 14, 0, 16}
+ ARRAY_SIZE(dot11lcn_aux_gain_idx_tbl_rev0), 14, 0, 16}
,
{&dot11lcn_gain_idx_tbl_rev0,
- sizeof(dot11lcn_gain_idx_tbl_rev0) /
- sizeof(dot11lcn_gain_idx_tbl_rev0[0]), 13, 0, 32}
+ ARRAY_SIZE(dot11lcn_gain_idx_tbl_rev0), 13, 0, 32}
,
};
static const struct phytbl_info dot11lcnphytbl_rx_gain_info_rev1[] = {
{&dot11lcn_gain_tbl_rev1,
- sizeof(dot11lcn_gain_tbl_rev1) / sizeof(dot11lcn_gain_tbl_rev1[0]), 18,
+ ARRAY_SIZE(dot11lcn_gain_tbl_rev1), 18,
0, 32}
,
{&dot11lcn_aux_gain_idx_tbl_rev0,
- sizeof(dot11lcn_aux_gain_idx_tbl_rev0) /
- sizeof(dot11lcn_aux_gain_idx_tbl_rev0[0]), 14, 0, 16}
+ ARRAY_SIZE(dot11lcn_aux_gain_idx_tbl_rev0), 14, 0, 16}
,
{&dot11lcn_gain_idx_tbl_rev0,
- sizeof(dot11lcn_gain_idx_tbl_rev0) /
- sizeof(dot11lcn_gain_idx_tbl_rev0[0]), 13, 0, 32}
+ ARRAY_SIZE(dot11lcn_gain_idx_tbl_rev0), 13, 0, 32}
,
};
const struct phytbl_info dot11lcnphytbl_rx_gain_info_2G_rev2[] = {
{&dot11lcn_gain_tbl_2G,
- sizeof(dot11lcn_gain_tbl_2G) / sizeof(dot11lcn_gain_tbl_2G[0]), 18, 0,
+ ARRAY_SIZE(dot11lcn_gain_tbl_2G), 18, 0,
32}
,
{&dot11lcn_aux_gain_idx_tbl_2G,
- sizeof(dot11lcn_aux_gain_idx_tbl_2G) /
- sizeof(dot11lcn_aux_gain_idx_tbl_2G[0]), 14, 0, 16}
+ ARRAY_SIZE(dot11lcn_aux_gain_idx_tbl_2G), 14, 0, 16}
,
{&dot11lcn_gain_idx_tbl_2G,
- sizeof(dot11lcn_gain_idx_tbl_2G) / sizeof(dot11lcn_gain_idx_tbl_2G[0]),
+ ARRAY_SIZE(dot11lcn_gain_idx_tbl_2G),
13, 0, 32}
,
{&dot11lcn_gain_val_tbl_2G,
- sizeof(dot11lcn_gain_val_tbl_2G) / sizeof(dot11lcn_gain_val_tbl_2G[0]),
+ ARRAY_SIZE(dot11lcn_gain_val_tbl_2G),
17, 0, 8}
};
const struct phytbl_info dot11lcnphytbl_rx_gain_info_5G_rev2[] = {
{&dot11lcn_gain_tbl_5G,
- sizeof(dot11lcn_gain_tbl_5G) / sizeof(dot11lcn_gain_tbl_5G[0]), 18, 0,
+ ARRAY_SIZE(dot11lcn_gain_tbl_5G), 18, 0,
32}
,
{&dot11lcn_aux_gain_idx_tbl_5G,
- sizeof(dot11lcn_aux_gain_idx_tbl_5G) /
- sizeof(dot11lcn_aux_gain_idx_tbl_5G[0]), 14, 0, 16}
+ ARRAY_SIZE(dot11lcn_aux_gain_idx_tbl_5G), 14, 0, 16}
,
{&dot11lcn_gain_idx_tbl_5G,
- sizeof(dot11lcn_gain_idx_tbl_5G) / sizeof(dot11lcn_gain_idx_tbl_5G[0]),
+ ARRAY_SIZE(dot11lcn_gain_idx_tbl_5G),
13, 0, 32}
,
{&dot11lcn_gain_val_tbl_5G,
- sizeof(dot11lcn_gain_val_tbl_5G) / sizeof(dot11lcn_gain_val_tbl_5G[0]),
+ ARRAY_SIZE(dot11lcn_gain_val_tbl_5G),
17, 0, 8}
};
const struct phytbl_info dot11lcnphytbl_rx_gain_info_extlna_2G_rev2[] = {
{&dot11lcn_gain_tbl_extlna_2G,
- sizeof(dot11lcn_gain_tbl_extlna_2G) /
- sizeof(dot11lcn_gain_tbl_extlna_2G[0]), 18, 0, 32}
+ ARRAY_SIZE(dot11lcn_gain_tbl_extlna_2G), 18, 0, 32}
,
{&dot11lcn_aux_gain_idx_tbl_extlna_2G,
- sizeof(dot11lcn_aux_gain_idx_tbl_extlna_2G) /
- sizeof(dot11lcn_aux_gain_idx_tbl_extlna_2G[0]), 14, 0, 16}
+ ARRAY_SIZE(dot11lcn_aux_gain_idx_tbl_extlna_2G), 14, 0, 16}
,
{&dot11lcn_gain_idx_tbl_extlna_2G,
- sizeof(dot11lcn_gain_idx_tbl_extlna_2G) /
- sizeof(dot11lcn_gain_idx_tbl_extlna_2G[0]), 13, 0, 32}
+ ARRAY_SIZE(dot11lcn_gain_idx_tbl_extlna_2G), 13, 0, 32}
,
{&dot11lcn_gain_val_tbl_extlna_2G,
- sizeof(dot11lcn_gain_val_tbl_extlna_2G) /
- sizeof(dot11lcn_gain_val_tbl_extlna_2G[0]), 17, 0, 8}
+ ARRAY_SIZE(dot11lcn_gain_val_tbl_extlna_2G), 17, 0, 8}
};
const struct phytbl_info dot11lcnphytbl_rx_gain_info_extlna_5G_rev2[] = {
{&dot11lcn_gain_tbl_5G,
- sizeof(dot11lcn_gain_tbl_5G) / sizeof(dot11lcn_gain_tbl_5G[0]), 18, 0,
+ ARRAY_SIZE(dot11lcn_gain_tbl_5G), 18, 0,
32}
,
{&dot11lcn_aux_gain_idx_tbl_5G,
- sizeof(dot11lcn_aux_gain_idx_tbl_5G) /
- sizeof(dot11lcn_aux_gain_idx_tbl_5G[0]), 14, 0, 16}
+ ARRAY_SIZE(dot11lcn_aux_gain_idx_tbl_5G), 14, 0, 16}
,
{&dot11lcn_gain_idx_tbl_5G,
- sizeof(dot11lcn_gain_idx_tbl_5G) / sizeof(dot11lcn_gain_idx_tbl_5G[0]),
+ ARRAY_SIZE(dot11lcn_gain_idx_tbl_5G),
13, 0, 32}
,
{&dot11lcn_gain_val_tbl_5G,
- sizeof(dot11lcn_gain_val_tbl_5G) / sizeof(dot11lcn_gain_val_tbl_5G[0]),
+ ARRAY_SIZE(dot11lcn_gain_val_tbl_5G),
17, 0, 8}
};
const u32 dot11lcnphytbl_rx_gain_info_sz_rev0 =
- sizeof(dot11lcnphytbl_rx_gain_info_rev0) /
- sizeof(dot11lcnphytbl_rx_gain_info_rev0[0]);
+ ARRAY_SIZE(dot11lcnphytbl_rx_gain_info_rev0);
const u32 dot11lcnphytbl_rx_gain_info_2G_rev2_sz =
- sizeof(dot11lcnphytbl_rx_gain_info_2G_rev2) /
- sizeof(dot11lcnphytbl_rx_gain_info_2G_rev2[0]);
+ ARRAY_SIZE(dot11lcnphytbl_rx_gain_info_2G_rev2);
const u32 dot11lcnphytbl_rx_gain_info_5G_rev2_sz =
- sizeof(dot11lcnphytbl_rx_gain_info_5G_rev2) /
- sizeof(dot11lcnphytbl_rx_gain_info_5G_rev2[0]);
+ ARRAY_SIZE(dot11lcnphytbl_rx_gain_info_5G_rev2);
static const u16 dot11lcn_min_sig_sq_tbl_rev0[] = {
0x014d,
@@ -2771,89 +2757,74 @@ static const u32 dot11lcn_papd_compdelta_tbl_rev0[] = {
const struct phytbl_info dot11lcnphytbl_info_rev0[] = {
{&dot11lcn_min_sig_sq_tbl_rev0,
- sizeof(dot11lcn_min_sig_sq_tbl_rev0) /
- sizeof(dot11lcn_min_sig_sq_tbl_rev0[0]), 2, 0, 16}
+ ARRAY_SIZE(dot11lcn_min_sig_sq_tbl_rev0), 2, 0, 16}
,
{&dot11lcn_noise_scale_tbl_rev0,
- sizeof(dot11lcn_noise_scale_tbl_rev0) /
- sizeof(dot11lcn_noise_scale_tbl_rev0[0]), 1, 0, 16}
+ ARRAY_SIZE(dot11lcn_noise_scale_tbl_rev0), 1, 0, 16}
,
{&dot11lcn_fltr_ctrl_tbl_rev0,
- sizeof(dot11lcn_fltr_ctrl_tbl_rev0) /
- sizeof(dot11lcn_fltr_ctrl_tbl_rev0[0]), 11, 0, 32}
+ ARRAY_SIZE(dot11lcn_fltr_ctrl_tbl_rev0), 11, 0, 32}
,
{&dot11lcn_ps_ctrl_tbl_rev0,
- sizeof(dot11lcn_ps_ctrl_tbl_rev0) /
- sizeof(dot11lcn_ps_ctrl_tbl_rev0[0]), 12, 0, 32}
+ ARRAY_SIZE(dot11lcn_ps_ctrl_tbl_rev0), 12, 0, 32}
,
{&dot11lcn_gain_idx_tbl_rev0,
- sizeof(dot11lcn_gain_idx_tbl_rev0) /
- sizeof(dot11lcn_gain_idx_tbl_rev0[0]), 13, 0, 32}
+ ARRAY_SIZE(dot11lcn_gain_idx_tbl_rev0), 13, 0, 32}
,
{&dot11lcn_aux_gain_idx_tbl_rev0,
- sizeof(dot11lcn_aux_gain_idx_tbl_rev0) /
- sizeof(dot11lcn_aux_gain_idx_tbl_rev0[0]), 14, 0, 16}
+ ARRAY_SIZE(dot11lcn_aux_gain_idx_tbl_rev0), 14, 0, 16}
,
{&dot11lcn_sw_ctrl_tbl_rev0,
- sizeof(dot11lcn_sw_ctrl_tbl_rev0) /
- sizeof(dot11lcn_sw_ctrl_tbl_rev0[0]), 15, 0, 16}
+ ARRAY_SIZE(dot11lcn_sw_ctrl_tbl_rev0), 15, 0, 16}
,
{&dot11lcn_nf_table_rev0,
- sizeof(dot11lcn_nf_table_rev0) / sizeof(dot11lcn_nf_table_rev0[0]), 16,
+ ARRAY_SIZE(dot11lcn_nf_table_rev0), 16,
0, 8}
,
{&dot11lcn_gain_val_tbl_rev0,
- sizeof(dot11lcn_gain_val_tbl_rev0) /
- sizeof(dot11lcn_gain_val_tbl_rev0[0]), 17, 0, 8}
+ ARRAY_SIZE(dot11lcn_gain_val_tbl_rev0), 17, 0, 8}
,
{&dot11lcn_gain_tbl_rev0,
- sizeof(dot11lcn_gain_tbl_rev0) / sizeof(dot11lcn_gain_tbl_rev0[0]), 18,
+ ARRAY_SIZE(dot11lcn_gain_tbl_rev0), 18,
0, 32}
,
{&dot11lcn_spur_tbl_rev0,
- sizeof(dot11lcn_spur_tbl_rev0) / sizeof(dot11lcn_spur_tbl_rev0[0]), 20,
+ ARRAY_SIZE(dot11lcn_spur_tbl_rev0), 20,
0, 8}
,
{&dot11lcn_unsup_mcs_tbl_rev0,
- sizeof(dot11lcn_unsup_mcs_tbl_rev0) /
- sizeof(dot11lcn_unsup_mcs_tbl_rev0[0]), 23, 0, 16}
+ ARRAY_SIZE(dot11lcn_unsup_mcs_tbl_rev0), 23, 0, 16}
,
{&dot11lcn_iq_local_tbl_rev0,
- sizeof(dot11lcn_iq_local_tbl_rev0) /
- sizeof(dot11lcn_iq_local_tbl_rev0[0]), 0, 0, 16}
+ ARRAY_SIZE(dot11lcn_iq_local_tbl_rev0), 0, 0, 16}
,
{&dot11lcn_papd_compdelta_tbl_rev0,
- sizeof(dot11lcn_papd_compdelta_tbl_rev0) /
- sizeof(dot11lcn_papd_compdelta_tbl_rev0[0]), 24, 0, 32}
+ ARRAY_SIZE(dot11lcn_papd_compdelta_tbl_rev0), 24, 0, 32}
,
};
const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313 = {
&dot11lcn_sw_ctrl_tbl_4313_rev0,
- sizeof(dot11lcn_sw_ctrl_tbl_4313_rev0) /
- sizeof(dot11lcn_sw_ctrl_tbl_4313_rev0[0]), 15, 0, 16
+ ARRAY_SIZE(dot11lcn_sw_ctrl_tbl_4313_rev0), 15, 0, 16
};
const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_epa = {
&dot11lcn_sw_ctrl_tbl_4313_epa_rev0,
- sizeof(dot11lcn_sw_ctrl_tbl_4313_epa_rev0) /
- sizeof(dot11lcn_sw_ctrl_tbl_4313_epa_rev0[0]), 15, 0, 16
+ ARRAY_SIZE(dot11lcn_sw_ctrl_tbl_4313_epa_rev0), 15, 0, 16
};
const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_bt_epa = {
&dot11lcn_sw_ctrl_tbl_4313_epa_rev0_combo,
- sizeof(dot11lcn_sw_ctrl_tbl_4313_epa_rev0_combo) /
- sizeof(dot11lcn_sw_ctrl_tbl_4313_epa_rev0_combo[0]), 15, 0, 16
+ ARRAY_SIZE(dot11lcn_sw_ctrl_tbl_4313_epa_rev0_combo), 15, 0, 16
};
const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_bt_epa_p250 = {
&dot11lcn_sw_ctrl_tbl_4313_bt_epa_p250_rev0,
- sizeof(dot11lcn_sw_ctrl_tbl_4313_bt_epa_p250_rev0) /
- sizeof(dot11lcn_sw_ctrl_tbl_4313_bt_epa_p250_rev0[0]), 15, 0, 16
+ ARRAY_SIZE(dot11lcn_sw_ctrl_tbl_4313_bt_epa_p250_rev0), 15, 0, 16
};
const u32 dot11lcnphytbl_info_sz_rev0 =
- sizeof(dot11lcnphytbl_info_rev0) / sizeof(dot11lcnphytbl_info_rev0[0]);
+ ARRAY_SIZE(dot11lcnphytbl_info_rev0);
const struct lcnphy_tx_gain_tbl_entry
dot11lcnphy_2GHz_extPA_gaintable_rev0[128] = {
--
1.7.10.4
On Tuesday 13 August 2013 22:03:27 Arend van Spriel wrote:
> This series replaces the patch "[PATCH 12/12] brcmsmac: support 4313iPA"
> with Message-ID: <[email protected]>.
>
> It has been split up into individual patches. Please test this series
> especially if you had issues with the original commit b6fc28a that was
> reverted.
>
> Cc: Jonas Gorski <[email protected]>
> Cc: David Herrmann <[email protected]>
> Cc: Maximilian Engelhardt <[email protected]>
> Cc: David Costa <[email protected]>
>
> Arend van Spriel (13):
> brcmsmac: cosmetic change in phy_lcn.c
> brcmsmac: change pa_gain for bcm4313 iPA
> brcmsmac: use ARRAY_SIZE in phytbl_lcn.c
> brcmsmac: add switch control table for BCM4313 iPA BT-combo cards
> brcmsmac: add debug info message providing phy and radio info
> brcmsmac: update transmit gain table for lcn phy
> brcmsmac: change lcnphy receive i/q calibration routine
> brcmsmac: fix TSSI idle estimation
> brcmsmac: avoid calling set_txpwr_by_index() twice
> brcmsmac: rework switch control table init including iPA BT-combo
> brcmsmac: correct phy registers for TSSI-based power control
> brcmsmac: reinitialize TSSI power control upon channel switch
> brcmsmac: add support for BCM4313 iPA variant
>
> drivers/net/wireless/brcm80211/brcmsmac/main.c | 4 +-
> .../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 397
> +++++++++++-------- .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c |
> 405 +++++++++++--------- .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h
> | 1 +
> 4 files changed, 475 insertions(+), 332 deletions(-)
Hello Arend,
I finally had some time to test your patches.
On my hardware I couldn't find any regressions with these patches. I also
verified that the reception problems I had with my card are fixed by these
patches.
I did test the patches on top of 3.10.5 as they did apply without any
problems.
Greetings,
Maxi