2013-08-13 20:04:32

by Arend van Spriel

[permalink] [raw]
Subject: [RFT 00/13] brcmsmac: bcm4313 iPA related patches

This series replaces the patch "[PATCH 12/12] brcmsmac: support 4313iPA"
with Message-ID: <[email protected]>.

It has been split up into individual patches. Please test this series
especially if you had issues with the original commit b6fc28a that was
reverted.

Cc: Jonas Gorski <[email protected]>
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>

Arend van Spriel (13):
brcmsmac: cosmetic change in phy_lcn.c
brcmsmac: change pa_gain for bcm4313 iPA
brcmsmac: use ARRAY_SIZE in phytbl_lcn.c
brcmsmac: add switch control table for BCM4313 iPA BT-combo cards
brcmsmac: add debug info message providing phy and radio info
brcmsmac: update transmit gain table for lcn phy
brcmsmac: change lcnphy receive i/q calibration routine
brcmsmac: fix TSSI idle estimation
brcmsmac: avoid calling set_txpwr_by_index() twice
brcmsmac: rework switch control table init including iPA BT-combo
brcmsmac: correct phy registers for TSSI-based power control
brcmsmac: reinitialize TSSI power control upon channel switch
brcmsmac: add support for BCM4313 iPA variant

drivers/net/wireless/brcm80211/brcmsmac/main.c | 4 +-
.../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 397 +++++++++++--------
.../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c | 405 +++++++++++---------
.../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h | 1 +
4 files changed, 475 insertions(+), 332 deletions(-)

--
1.7.10.4




2013-08-13 20:04:34

by Arend van Spriel

[permalink] [raw]
Subject: [RFT V2 02/13] brcmsmac: change pa_gain for bcm4313 iPA

The function wlc_lcnphy_load_tx_gain_table() has a target PA
gain specified for the iPA variant of the bcm4313. This gain
value is reduced to avoid PA distortion. The if-statement is
removed because it was rather redundant in the first place.
Please not that this patch does not provide full iPA support.

Cc: Jonas Gorski <[email protected]>
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Reviewed-by: Hante Meuleman <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 7 ++-----
1 file changed, 2 insertions(+), 5 deletions(-)

diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index e646ba0..8dc5d0f 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -4282,13 +4282,10 @@ wlc_lcnphy_load_tx_gain_table(struct brcms_phy *pi,
u16 pa_gain;
u16 gm_gain;

- if (CHSPEC_IS5G(pi->radio_chanspec))
- pa_gain = 0x70;
- else
- pa_gain = 0x70;
-
if (pi->sh->boardflags & BFL_FEM)
pa_gain = 0x10;
+ else
+ pa_gain = 0x60;
tab.tbl_id = LCNPHY_TBL_ID_TXPWRCTL;
tab.tbl_width = 32;
tab.tbl_len = 1;
--
1.7.10.4



2013-08-13 20:04:34

by Arend van Spriel

[permalink] [raw]
Subject: [RFT V2 04/13] brcmsmac: add switch control table for BCM4313 iPA BT-combo cards

The bcm4313 iPA BT-WLAN combo cards need to be initialized with
a different switch control table. This patch adds that table.

Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
.../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c | 72 ++++++++++++++++++++
.../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h | 1 +
2 files changed, 73 insertions(+)

diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
index deae3a7..36c41df 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
@@ -2044,6 +2044,73 @@ static const u16 dot11lcn_sw_ctrl_tbl_4313_rev0[] = {
0x0005,
};

+static const u16 dot11lcn_sw_ctrl_tbl_4313_ipa_rev0_combo[] = {
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+ 0x0005,
+ 0x0006,
+ 0x0009,
+ 0x000a,
+};
+
static const u16 dot11lcn_sw_ctrl_tbl_rev0[] = {
0x0004,
0x0004,
@@ -2808,6 +2875,11 @@ const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313 = {
ARRAY_SIZE(dot11lcn_sw_ctrl_tbl_4313_rev0), 15, 0, 16
};

+const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_bt_ipa = {
+ &dot11lcn_sw_ctrl_tbl_4313_ipa_rev0_combo,
+ ARRAY_SIZE(dot11lcn_sw_ctrl_tbl_4313_ipa_rev0_combo), 15, 0, 16
+};
+
const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_epa = {
&dot11lcn_sw_ctrl_tbl_4313_epa_rev0,
ARRAY_SIZE(dot11lcn_sw_ctrl_tbl_4313_epa_rev0), 15, 0, 16
diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h
index 5f75e16..489422a 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h
@@ -20,6 +20,7 @@
extern const struct phytbl_info dot11lcnphytbl_rx_gain_info_rev0[];
extern const u32 dot11lcnphytbl_rx_gain_info_sz_rev0;
extern const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313;
+extern const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_bt_ipa;
extern const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_epa;
extern const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_epa_combo;
extern const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_bt_epa;
--
1.7.10.4



2013-08-14 10:33:05

by David Herrmann

[permalink] [raw]
Subject: Re: [RFT 00/13] brcmsmac: bcm4313 iPA related patches

Hi

On Tue, Aug 13, 2013 at 10:46 PM, Arend van Spriel <[email protected]> wrote:
> On 08/13/2013 10:09 PM, David Herrmann wrote:
>>
>> Hi
>>
>> On Tue, Aug 13, 2013 at 10:03 PM, Arend van Spriel <[email protected]>
>> wrote:
>>>
>>> This series replaces the patch "[PATCH 12/12] brcmsmac: support 4313iPA"
>>> with Message-ID: <[email protected]>.
>>>
>>> It has been split up into individual patches. Please test this series
>>> especially if you had issues with the original commit b6fc28a that was
>>> reverted.
>>>
>>> Cc: Jonas Gorski <[email protected]>
>>> Cc: David Herrmann <[email protected]>
>>> Cc: Maximilian Engelhardt <[email protected]>
>>> Cc: David Costa <[email protected]>
>>
>>
>> Is this available in a public branch that I can merge? And what should
>> be used as base? 3.11-rc5? linux-next?
>
>
> Indeed I should have mentioned. It applies on v3.11-rc5 for sure. Did not
> try linux-next.

All 13 patches applied cleanly on top of 3.11-rc5, everything works
fine even after a dozen of reconnects to different networks. No
additional delays.

Consider this whole series:
Tested-by: David Herrmann <[email protected]>

card info: Broadcom Corporation BCM4313 802.11b/g/n (0a5c:219c)
(builtin into my old Intel Atom N450 board)
I tested with 802.11g networks. I have only a/g networks here. I don't
know whether that matters.

Cheers
David

2013-08-14 18:16:48

by Arend van Spriel

[permalink] [raw]
Subject: Re: [RFT 00/13] brcmsmac: bcm4313 iPA related patches

On 08/14/2013 12:33 PM, David Herrmann wrote:
> Hi
>
> On Tue, Aug 13, 2013 at 10:46 PM, Arend van Spriel <[email protected]> wrote:
>> On 08/13/2013 10:09 PM, David Herrmann wrote:
>>>
>>> Hi
>>>
>>> On Tue, Aug 13, 2013 at 10:03 PM, Arend van Spriel <[email protected]>
>>> wrote:
>>>>
>>>> This series replaces the patch "[PATCH 12/12] brcmsmac: support 4313iPA"
>>>> with Message-ID: <[email protected]>.
>>>>
>>>> It has been split up into individual patches. Please test this series
>>>> especially if you had issues with the original commit b6fc28a that was
>>>> reverted.
>>>>
>>>> Cc: Jonas Gorski <[email protected]>
>>>> Cc: David Herrmann <[email protected]>
>>>> Cc: Maximilian Engelhardt <[email protected]>
>>>> Cc: David Costa <[email protected]>
>>>
>>>
>>> Is this available in a public branch that I can merge? And what should
>>> be used as base? 3.11-rc5? linux-next?
>>
>>
>> Indeed I should have mentioned. It applies on v3.11-rc5 for sure. Did not
>> try linux-next.
>
> All 13 patches applied cleanly on top of 3.11-rc5, everything works
> fine even after a dozen of reconnects to different networks. No
> additional delays.
>
> Consider this whole series:
> Tested-by: David Herrmann <[email protected]>
>
> card info: Broadcom Corporation BCM4313 802.11b/g/n (0a5c:219c)
> (builtin into my old Intel Atom N450 board)
> I tested with 802.11g networks. I have only a/g networks here. I don't
> know whether that matters.

As this series modifies the phy code, I would say no.

Thanks for verifying this works for you.

Regards,
Arend


2013-08-13 20:04:44

by Arend van Spriel

[permalink] [raw]
Subject: [RFT V2 10/13] brcmsmac: rework switch control table init including iPA BT-combo

Rework the code path in lcnphy tbl_init() for switch control
table programming. This also takes the iPA BT-combo card into
account.

Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
.../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 31 ++++++++++----------
1 file changed, 16 insertions(+), 15 deletions(-)

diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index e02729d..732371c 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -4573,6 +4573,7 @@ static void wlc_lcnphy_tbl_init(struct brcms_phy *pi)
uint idx;
u8 phybw40;
struct phytbl_info tab;
+ const struct phytbl_info *tb;
u32 val;

phybw40 = CHSPEC_IS40(pi->radio_chanspec);
@@ -4619,7 +4620,6 @@ static void wlc_lcnphy_tbl_init(struct brcms_phy *pi)
}

if (LCNREV_IS(pi->pubpi.phy_rev, 2)) {
- const struct phytbl_info *tb;
int l;

if (CHSPEC_IS2G(pi->radio_chanspec)) {
@@ -4640,21 +4640,22 @@ static void wlc_lcnphy_tbl_init(struct brcms_phy *pi)
wlc_lcnphy_write_table(pi, &tb[idx]);
}

- if ((pi->sh->boardflags & BFL_FEM)
- && !(pi->sh->boardflags & BFL_FEM_BT))
- wlc_lcnphy_write_table(pi, &dot11lcn_sw_ctrl_tbl_info_4313_epa);
- else if (pi->sh->boardflags & BFL_FEM_BT) {
- if (pi->sh->boardrev < 0x1250)
- wlc_lcnphy_write_table(
- pi,
- &dot11lcn_sw_ctrl_tbl_info_4313_bt_epa);
+ if (pi->sh->boardflags & BFL_FEM) {
+ if (pi->sh->boardflags & BFL_FEM_BT) {
+ if (pi->sh->boardrev < 0x1250)
+ tb = &dot11lcn_sw_ctrl_tbl_info_4313_bt_epa;
+ else
+ tb = &dot11lcn_sw_ctrl_tbl_info_4313_bt_epa_p250;
+ } else {
+ tb = &dot11lcn_sw_ctrl_tbl_info_4313_epa;
+ }
+ } else {
+ if (pi->sh->boardflags & BFL_FEM_BT)
+ tb = &dot11lcn_sw_ctrl_tbl_info_4313_bt_ipa;
else
- wlc_lcnphy_write_table(
- pi,
- &dot11lcn_sw_ctrl_tbl_info_4313_bt_epa_p250);
- } else
- wlc_lcnphy_write_table(pi, &dot11lcn_sw_ctrl_tbl_info_4313);
-
+ tb = &dot11lcn_sw_ctrl_tbl_info_4313;
+ }
+ wlc_lcnphy_write_table(pi, tb);
wlc_lcnphy_load_rfpower(pi);

wlc_lcnphy_clear_papd_comptable(pi);
--
1.7.10.4



2013-08-13 20:04:37

by Arend van Spriel

[permalink] [raw]
Subject: [RFT V2 12/13] brcmsmac: reinitialize TSSI power control upon channel switch

When changing channels the TSSI based power control needs to be
reinitialized.

Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 2 ++
1 file changed, 2 insertions(+)

diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index a0a268d..6e6bc28 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -5019,6 +5019,8 @@ void wlc_phy_chanspec_set_lcnphy(struct brcms_phy *pi, u16 chanspec)
wlc_lcnphy_load_tx_iir_filter(pi, true, 3);

mod_phy_reg(pi, 0x4eb, (0x7 << 3), (1) << 3);
+ if (wlc_lcnphy_tssi_based_pwr_ctrl_enabled(pi))
+ wlc_lcnphy_tssi_setup(pi);
}

void wlc_phy_detach_lcnphy(struct brcms_phy *pi)
--
1.7.10.4



2013-08-13 20:04:32

by Arend van Spriel

[permalink] [raw]
Subject: [RFT V2 01/13] brcmsmac: cosmetic change in phy_lcn.c

Cleaning up some code fragments reducing indentation and uncluttering
some lines. Apart from whitespace there are no actual code changes
made.

Cc: Jonas Gorski <[email protected]>
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
.../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 213 ++++++++++----------
1 file changed, 106 insertions(+), 107 deletions(-)

diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index 3d6b16c..e646ba0 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -1137,8 +1137,9 @@ wlc_lcnphy_set_rx_gain_by_distribution(struct brcms_phy *pi,
gain0_15 = ((biq1 & 0xf) << 12) |
((tia & 0xf) << 8) |
((lna2 & 0x3) << 6) |
- ((lna2 &
- 0x3) << 4) | ((lna1 & 0x3) << 2) | ((lna1 & 0x3) << 0);
+ ((lna2 & 0x3) << 4) |
+ ((lna1 & 0x3) << 2) |
+ ((lna1 & 0x3) << 0);

mod_phy_reg(pi, 0x4b6, (0xffff << 0), gain0_15 << 0);
mod_phy_reg(pi, 0x4b7, (0xf << 0), gain16_19 << 0);
@@ -1368,126 +1369,124 @@ wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi,
goto cal_done;
}

- if (module == 1) {
+ WARN_ON(module != 1);
+ tx_pwr_ctrl = wlc_lcnphy_get_tx_pwr_ctrl(pi);
+ wlc_lcnphy_set_tx_pwr_ctrl(pi, LCNPHY_TX_PWR_CTRL_OFF);

- tx_pwr_ctrl = wlc_lcnphy_get_tx_pwr_ctrl(pi);
- wlc_lcnphy_set_tx_pwr_ctrl(pi, LCNPHY_TX_PWR_CTRL_OFF);
+ for (i = 0; i < 11; i++)
+ values_to_save[i] =
+ read_radio_reg(pi, rxiq_cal_rf_reg[i]);
+ Core1TxControl_old = read_phy_reg(pi, 0x631);
+
+ or_phy_reg(pi, 0x631, 0x0015);
+
+ RFOverride0_old = read_phy_reg(pi, 0x44c);
+ RFOverrideVal0_old = read_phy_reg(pi, 0x44d);
+ rfoverride2_old = read_phy_reg(pi, 0x4b0);
+ rfoverride2val_old = read_phy_reg(pi, 0x4b1);
+ rfoverride3_old = read_phy_reg(pi, 0x4f9);
+ rfoverride3val_old = read_phy_reg(pi, 0x4fa);
+ rfoverride4_old = read_phy_reg(pi, 0x938);
+ rfoverride4val_old = read_phy_reg(pi, 0x939);
+ afectrlovr_old = read_phy_reg(pi, 0x43b);
+ afectrlovrval_old = read_phy_reg(pi, 0x43c);
+ old_sslpnCalibClkEnCtrl = read_phy_reg(pi, 0x6da);
+ old_sslpnRxFeClkEnCtrl = read_phy_reg(pi, 0x6db);

- for (i = 0; i < 11; i++)
- values_to_save[i] =
- read_radio_reg(pi, rxiq_cal_rf_reg[i]);
- Core1TxControl_old = read_phy_reg(pi, 0x631);
-
- or_phy_reg(pi, 0x631, 0x0015);
-
- RFOverride0_old = read_phy_reg(pi, 0x44c);
- RFOverrideVal0_old = read_phy_reg(pi, 0x44d);
- rfoverride2_old = read_phy_reg(pi, 0x4b0);
- rfoverride2val_old = read_phy_reg(pi, 0x4b1);
- rfoverride3_old = read_phy_reg(pi, 0x4f9);
- rfoverride3val_old = read_phy_reg(pi, 0x4fa);
- rfoverride4_old = read_phy_reg(pi, 0x938);
- rfoverride4val_old = read_phy_reg(pi, 0x939);
- afectrlovr_old = read_phy_reg(pi, 0x43b);
- afectrlovrval_old = read_phy_reg(pi, 0x43c);
- old_sslpnCalibClkEnCtrl = read_phy_reg(pi, 0x6da);
- old_sslpnRxFeClkEnCtrl = read_phy_reg(pi, 0x6db);
-
- tx_gain_override_old = wlc_lcnphy_tx_gain_override_enabled(pi);
- if (tx_gain_override_old) {
- wlc_lcnphy_get_tx_gain(pi, &old_gains);
- tx_gain_index_old = pi_lcn->lcnphy_current_index;
- }
+ tx_gain_override_old = wlc_lcnphy_tx_gain_override_enabled(pi);
+ if (tx_gain_override_old) {
+ wlc_lcnphy_get_tx_gain(pi, &old_gains);
+ tx_gain_index_old = pi_lcn->lcnphy_current_index;
+ }

- wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_idx);
+ wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_idx);

- mod_phy_reg(pi, 0x4f9, (0x1 << 0), 1 << 0);
- mod_phy_reg(pi, 0x4fa, (0x1 << 0), 0 << 0);
+ mod_phy_reg(pi, 0x4f9, (0x1 << 0), 1 << 0);
+ mod_phy_reg(pi, 0x4fa, (0x1 << 0), 0 << 0);

- mod_phy_reg(pi, 0x43b, (0x1 << 1), 1 << 1);
- mod_phy_reg(pi, 0x43c, (0x1 << 1), 0 << 1);
+ mod_phy_reg(pi, 0x43b, (0x1 << 1), 1 << 1);
+ mod_phy_reg(pi, 0x43c, (0x1 << 1), 0 << 1);

- write_radio_reg(pi, RADIO_2064_REG116, 0x06);
- write_radio_reg(pi, RADIO_2064_REG12C, 0x07);
- write_radio_reg(pi, RADIO_2064_REG06A, 0xd3);
- write_radio_reg(pi, RADIO_2064_REG098, 0x03);
- write_radio_reg(pi, RADIO_2064_REG00B, 0x7);
- mod_radio_reg(pi, RADIO_2064_REG113, 1 << 4, 1 << 4);
- write_radio_reg(pi, RADIO_2064_REG01D, 0x01);
- write_radio_reg(pi, RADIO_2064_REG114, 0x01);
- write_radio_reg(pi, RADIO_2064_REG02E, 0x10);
- write_radio_reg(pi, RADIO_2064_REG12A, 0x08);
-
- mod_phy_reg(pi, 0x938, (0x1 << 0), 1 << 0);
- mod_phy_reg(pi, 0x939, (0x1 << 0), 0 << 0);
- mod_phy_reg(pi, 0x938, (0x1 << 1), 1 << 1);
- mod_phy_reg(pi, 0x939, (0x1 << 1), 1 << 1);
- mod_phy_reg(pi, 0x938, (0x1 << 2), 1 << 2);
- mod_phy_reg(pi, 0x939, (0x1 << 2), 1 << 2);
- mod_phy_reg(pi, 0x938, (0x1 << 3), 1 << 3);
- mod_phy_reg(pi, 0x939, (0x1 << 3), 1 << 3);
- mod_phy_reg(pi, 0x938, (0x1 << 5), 1 << 5);
- mod_phy_reg(pi, 0x939, (0x1 << 5), 0 << 5);
-
- mod_phy_reg(pi, 0x43b, (0x1 << 0), 1 << 0);
- mod_phy_reg(pi, 0x43c, (0x1 << 0), 0 << 0);
-
- wlc_lcnphy_start_tx_tone(pi, 2000, 120, 0);
- write_phy_reg(pi, 0x6da, 0xffff);
- or_phy_reg(pi, 0x6db, 0x3);
- wlc_lcnphy_set_trsw_override(pi, tx_switch, rx_switch);
- wlc_lcnphy_rx_gain_override_enable(pi, true);
-
- tia_gain = 8;
- rx_pwr_threshold = 950;
- while (tia_gain > 0) {
- tia_gain -= 1;
- wlc_lcnphy_set_rx_gain_by_distribution(pi,
- 0, 0, 2, 2,
- (u16)
- tia_gain, 1, 0);
- udelay(500);
+ write_radio_reg(pi, RADIO_2064_REG116, 0x06);
+ write_radio_reg(pi, RADIO_2064_REG12C, 0x07);
+ write_radio_reg(pi, RADIO_2064_REG06A, 0xd3);
+ write_radio_reg(pi, RADIO_2064_REG098, 0x03);
+ write_radio_reg(pi, RADIO_2064_REG00B, 0x7);
+ mod_radio_reg(pi, RADIO_2064_REG113, 1 << 4, 1 << 4);
+ write_radio_reg(pi, RADIO_2064_REG01D, 0x01);
+ write_radio_reg(pi, RADIO_2064_REG114, 0x01);
+ write_radio_reg(pi, RADIO_2064_REG02E, 0x10);
+ write_radio_reg(pi, RADIO_2064_REG12A, 0x08);
+
+ mod_phy_reg(pi, 0x938, (0x1 << 0), 1 << 0);
+ mod_phy_reg(pi, 0x939, (0x1 << 0), 0 << 0);
+ mod_phy_reg(pi, 0x938, (0x1 << 1), 1 << 1);
+ mod_phy_reg(pi, 0x939, (0x1 << 1), 1 << 1);
+ mod_phy_reg(pi, 0x938, (0x1 << 2), 1 << 2);
+ mod_phy_reg(pi, 0x939, (0x1 << 2), 1 << 2);
+ mod_phy_reg(pi, 0x938, (0x1 << 3), 1 << 3);
+ mod_phy_reg(pi, 0x939, (0x1 << 3), 1 << 3);
+ mod_phy_reg(pi, 0x938, (0x1 << 5), 1 << 5);
+ mod_phy_reg(pi, 0x939, (0x1 << 5), 0 << 5);

- received_power =
- wlc_lcnphy_measure_digital_power(pi, 2000);
- if (received_power < rx_pwr_threshold)
- break;
- }
- result = wlc_lcnphy_calc_rx_iq_comp(pi, 0xffff);
+ mod_phy_reg(pi, 0x43b, (0x1 << 0), 1 << 0);
+ mod_phy_reg(pi, 0x43c, (0x1 << 0), 0 << 0);

- wlc_lcnphy_stop_tx_tone(pi);
+ wlc_lcnphy_start_tx_tone(pi, 2000, 120, 0);
+ write_phy_reg(pi, 0x6da, 0xffff);
+ or_phy_reg(pi, 0x6db, 0x3);
+ wlc_lcnphy_set_trsw_override(pi, tx_switch, rx_switch);
+ wlc_lcnphy_rx_gain_override_enable(pi, true);

- write_phy_reg(pi, 0x631, Core1TxControl_old);
+ tia_gain = 8;
+ rx_pwr_threshold = 950;
+ while (tia_gain > 0) {
+ tia_gain -= 1;
+ wlc_lcnphy_set_rx_gain_by_distribution(pi,
+ 0, 0, 2, 2,
+ (u16)
+ tia_gain, 1, 0);
+ udelay(500);

- write_phy_reg(pi, 0x44c, RFOverrideVal0_old);
- write_phy_reg(pi, 0x44d, RFOverrideVal0_old);
- write_phy_reg(pi, 0x4b0, rfoverride2_old);
- write_phy_reg(pi, 0x4b1, rfoverride2val_old);
- write_phy_reg(pi, 0x4f9, rfoverride3_old);
- write_phy_reg(pi, 0x4fa, rfoverride3val_old);
- write_phy_reg(pi, 0x938, rfoverride4_old);
- write_phy_reg(pi, 0x939, rfoverride4val_old);
- write_phy_reg(pi, 0x43b, afectrlovr_old);
- write_phy_reg(pi, 0x43c, afectrlovrval_old);
- write_phy_reg(pi, 0x6da, old_sslpnCalibClkEnCtrl);
- write_phy_reg(pi, 0x6db, old_sslpnRxFeClkEnCtrl);
+ received_power =
+ wlc_lcnphy_measure_digital_power(pi, 2000);
+ if (received_power < rx_pwr_threshold)
+ break;
+ }
+ result = wlc_lcnphy_calc_rx_iq_comp(pi, 0xffff);

- wlc_lcnphy_clear_trsw_override(pi);
+ wlc_lcnphy_stop_tx_tone(pi);

- mod_phy_reg(pi, 0x44c, (0x1 << 2), 0 << 2);
+ write_phy_reg(pi, 0x631, Core1TxControl_old);
+
+ write_phy_reg(pi, 0x44c, RFOverrideVal0_old);
+ write_phy_reg(pi, 0x44d, RFOverrideVal0_old);
+ write_phy_reg(pi, 0x4b0, rfoverride2_old);
+ write_phy_reg(pi, 0x4b1, rfoverride2val_old);
+ write_phy_reg(pi, 0x4f9, rfoverride3_old);
+ write_phy_reg(pi, 0x4fa, rfoverride3val_old);
+ write_phy_reg(pi, 0x938, rfoverride4_old);
+ write_phy_reg(pi, 0x939, rfoverride4val_old);
+ write_phy_reg(pi, 0x43b, afectrlovr_old);
+ write_phy_reg(pi, 0x43c, afectrlovrval_old);
+ write_phy_reg(pi, 0x6da, old_sslpnCalibClkEnCtrl);
+ write_phy_reg(pi, 0x6db, old_sslpnRxFeClkEnCtrl);

- for (i = 0; i < 11; i++)
- write_radio_reg(pi, rxiq_cal_rf_reg[i],
- values_to_save[i]);
+ wlc_lcnphy_clear_trsw_override(pi);

- if (tx_gain_override_old)
- wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_index_old);
- else
- wlc_lcnphy_disable_tx_gain_override(pi);
+ mod_phy_reg(pi, 0x44c, (0x1 << 2), 0 << 2);

- wlc_lcnphy_set_tx_pwr_ctrl(pi, tx_pwr_ctrl);
- wlc_lcnphy_rx_gain_override_enable(pi, false);
- }
+ for (i = 0; i < 11; i++)
+ write_radio_reg(pi, rxiq_cal_rf_reg[i],
+ values_to_save[i]);
+
+ if (tx_gain_override_old)
+ wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_index_old);
+ else
+ wlc_lcnphy_disable_tx_gain_override(pi);
+
+ wlc_lcnphy_set_tx_pwr_ctrl(pi, tx_pwr_ctrl);
+ wlc_lcnphy_rx_gain_override_enable(pi, false);

cal_done:
kfree(ptr);
--
1.7.10.4



2013-08-13 20:09:46

by David Herrmann

[permalink] [raw]
Subject: Re: [RFT 00/13] brcmsmac: bcm4313 iPA related patches

Hi

On Tue, Aug 13, 2013 at 10:03 PM, Arend van Spriel <[email protected]> wrote:
> This series replaces the patch "[PATCH 12/12] brcmsmac: support 4313iPA"
> with Message-ID: <[email protected]>.
>
> It has been split up into individual patches. Please test this series
> especially if you had issues with the original commit b6fc28a that was
> reverted.
>
> Cc: Jonas Gorski <[email protected]>
> Cc: David Herrmann <[email protected]>
> Cc: Maximilian Engelhardt <[email protected]>
> Cc: David Costa <[email protected]>

Is this available in a public branch that I can merge? And what should
be used as base? 3.11-rc5? linux-next?

Cheers
David

> Arend van Spriel (13):
> brcmsmac: cosmetic change in phy_lcn.c
> brcmsmac: change pa_gain for bcm4313 iPA
> brcmsmac: use ARRAY_SIZE in phytbl_lcn.c
> brcmsmac: add switch control table for BCM4313 iPA BT-combo cards
> brcmsmac: add debug info message providing phy and radio info
> brcmsmac: update transmit gain table for lcn phy
> brcmsmac: change lcnphy receive i/q calibration routine
> brcmsmac: fix TSSI idle estimation
> brcmsmac: avoid calling set_txpwr_by_index() twice
> brcmsmac: rework switch control table init including iPA BT-combo
> brcmsmac: correct phy registers for TSSI-based power control
> brcmsmac: reinitialize TSSI power control upon channel switch
> brcmsmac: add support for BCM4313 iPA variant
>
> drivers/net/wireless/brcm80211/brcmsmac/main.c | 4 +-
> .../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 397 +++++++++++--------
> .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c | 405 +++++++++++---------
> .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h | 1 +
> 4 files changed, 475 insertions(+), 332 deletions(-)
>
> --
> 1.7.10.4
>
>

2013-08-13 20:04:44

by Arend van Spriel

[permalink] [raw]
Subject: [RFT V2 13/13] brcmsmac: add support for BCM4313 iPA variant

This patch completes the changes needed for supporting the
iPA variant cards of the BCM4313 wireless chipset.

Cc: Jonas Gorski <[email protected]>
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
.../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 71 ++++++++++++++------
1 file changed, 51 insertions(+), 20 deletions(-)

diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index 6e6bc28..4ba5d62 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -1826,6 +1826,17 @@ wlc_lcnphy_radio_2064_channel_tune_4313(struct brcms_phy *pi, u8 channel)
write_radio_reg(pi, RADIO_2064_REG038, 3);
write_radio_reg(pi, RADIO_2064_REG091, 7);
}
+
+ if (!(pi->sh->boardflags & BFL_FEM)) {
+ u8 reg038[14] = {0xd, 0xe, 0xd, 0xd, 0xd, 0xc,
+ 0xa, 0xb, 0xb, 0x3, 0x3, 0x2, 0x0, 0x0};
+
+ write_radio_reg(pi, RADIO_2064_REG02A, 0xf);
+ write_radio_reg(pi, RADIO_2064_REG091, 0x3);
+ write_radio_reg(pi, RADIO_2064_REG038, 0x3);
+
+ write_radio_reg(pi, RADIO_2064_REG038, reg038[channel - 1]);
+ }
}

static int
@@ -2123,7 +2134,16 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi)
{
struct phytbl_info tab;
u32 rfseq, ind;
+ enum lcnphy_tssi_mode mode;
+ u8 tssi_sel;

+ if (pi->sh->boardflags & BFL_FEM) {
+ tssi_sel = 0x1;
+ mode = LCNPHY_TSSI_EXT;
+ } else {
+ tssi_sel = 0xe;
+ mode = LCNPHY_TSSI_POST_PA;
+ }
tab.tbl_id = LCNPHY_TBL_ID_TXPWRCTL;
tab.tbl_width = 32;
tab.tbl_ptr = &ind;
@@ -2144,7 +2164,7 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi)

mod_phy_reg(pi, 0x503, (0x1 << 4), (1) << 4);

- wlc_lcnphy_set_tssi_mux(pi, LCNPHY_TSSI_EXT);
+ wlc_lcnphy_set_tssi_mux(pi, mode);
mod_phy_reg(pi, 0x4a4, (0x1 << 14), (0) << 14);

mod_phy_reg(pi, 0x4a4, (0x1 << 15), (1) << 15);
@@ -2180,9 +2200,10 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi)
mod_phy_reg(pi, 0x49a, (0x1ff << 0), (0xff) << 0);

if (LCNREV_IS(pi->pubpi.phy_rev, 2)) {
- mod_radio_reg(pi, RADIO_2064_REG028, 0xf, 0xe);
+ mod_radio_reg(pi, RADIO_2064_REG028, 0xf, tssi_sel);
mod_radio_reg(pi, RADIO_2064_REG086, 0x4, 0x4);
} else {
+ mod_radio_reg(pi, RADIO_2064_REG028, 0x1e, tssi_sel << 1);
mod_radio_reg(pi, RADIO_2064_REG03A, 0x1, 1);
mod_radio_reg(pi, RADIO_2064_REG11A, 0x8, 1 << 3);
}
@@ -4358,8 +4379,11 @@ wlc_lcnphy_load_tx_gain_table(struct brcms_phy *pi,
tab.tbl_len = 1;
tab.tbl_ptr = &val;

+ /* fixed gm_gain value for iPA */
+ gm_gain = 15;
for (j = 0; j < 128; j++) {
- gm_gain = gain_table[j].gm;
+ if (pi->sh->boardflags & BFL_FEM)
+ gm_gain = gain_table[j].gm;
val = (((u32) pa_gain << 24) |
(gain_table[j].pad << 16) |
(gain_table[j].pga << 8) | gm_gain);
@@ -4570,7 +4594,10 @@ static void wlc_radio_2064_init(struct brcms_phy *pi)

write_phy_reg(pi, 0x4ea, 0x4688);

- mod_phy_reg(pi, 0x4eb, (0x7 << 0), 2 << 0);
+ if (pi->sh->boardflags & BFL_FEM)
+ mod_phy_reg(pi, 0x4eb, (0x7 << 0), 2 << 0);
+ else
+ mod_phy_reg(pi, 0x4eb, (0x7 << 0), 3 << 0);

mod_phy_reg(pi, 0x4eb, (0x7 << 6), 0 << 6);

@@ -4581,6 +4608,13 @@ static void wlc_radio_2064_init(struct brcms_phy *pi)
wlc_lcnphy_rcal(pi);

wlc_lcnphy_rc_cal(pi);
+
+ if (!(pi->sh->boardflags & BFL_FEM)) {
+ write_radio_reg(pi, RADIO_2064_REG032, 0x6f);
+ write_radio_reg(pi, RADIO_2064_REG033, 0x19);
+ write_radio_reg(pi, RADIO_2064_REG039, 0xe);
+ }
+
}

static void wlc_lcnphy_radio_init(struct brcms_phy *pi)
@@ -4611,22 +4645,20 @@ static void wlc_lcnphy_tbl_init(struct brcms_phy *pi)
wlc_lcnphy_write_table(pi, &tab);
}

- tab.tbl_id = LCNPHY_TBL_ID_RFSEQ;
- tab.tbl_width = 16;
- tab.tbl_ptr = &val;
- tab.tbl_len = 1;
-
- val = 114;
- tab.tbl_offset = 0;
- wlc_lcnphy_write_table(pi, &tab);
+ if (!(pi->sh->boardflags & BFL_FEM)) {
+ tab.tbl_id = LCNPHY_TBL_ID_RFSEQ;
+ tab.tbl_width = 16;
+ tab.tbl_ptr = &val;
+ tab.tbl_len = 1;

- val = 130;
- tab.tbl_offset = 1;
- wlc_lcnphy_write_table(pi, &tab);
+ val = 150;
+ tab.tbl_offset = 0;
+ wlc_lcnphy_write_table(pi, &tab);

- val = 6;
- tab.tbl_offset = 8;
- wlc_lcnphy_write_table(pi, &tab);
+ val = 220;
+ tab.tbl_offset = 1;
+ wlc_lcnphy_write_table(pi, &tab);
+ }

if (CHSPEC_IS2G(pi->radio_chanspec)) {
if (pi->sh->boardflags & BFL_FEM)
@@ -5059,8 +5091,7 @@ bool wlc_phy_attach_lcnphy(struct brcms_phy *pi)
if (!wlc_phy_txpwr_srom_read_lcnphy(pi))
return false;

- if ((pi->sh->boardflags & BFL_FEM) &&
- (LCNREV_IS(pi->pubpi.phy_rev, 1))) {
+ if (LCNREV_IS(pi->pubpi.phy_rev, 1)) {
if (pi_lcn->lcnphy_tempsense_option == 3) {
pi->hwpwrctrl = true;
pi->hwpwrctrl_capable = true;
--
1.7.10.4



2013-08-13 20:04:32

by Arend van Spriel

[permalink] [raw]
Subject: [RFT V2 06/13] brcmsmac: update transmit gain table for lcn phy

Update the transmit gain table for bcm4313 chip family.

Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
.../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c | 216 ++++++++++----------
1 file changed, 108 insertions(+), 108 deletions(-)

diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
index 36c41df..d7fa312 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
@@ -3031,134 +3031,134 @@ dot11lcnphy_2GHz_extPA_gaintable_rev0[128] = {
};

const struct lcnphy_tx_gain_tbl_entry dot11lcnphy_2GHz_gaintable_rev0[128] = {
- {7, 0, 31, 0, 72},
- {7, 0, 31, 0, 70},
- {7, 0, 31, 0, 68},
- {7, 0, 30, 0, 67},
- {7, 0, 29, 0, 68},
- {7, 0, 28, 0, 68},
- {7, 0, 27, 0, 69},
- {7, 0, 26, 0, 70},
- {7, 0, 25, 0, 70},
- {7, 0, 24, 0, 71},
- {7, 0, 23, 0, 72},
- {7, 0, 23, 0, 70},
- {7, 0, 22, 0, 71},
- {7, 0, 21, 0, 72},
- {7, 0, 21, 0, 70},
- {7, 0, 21, 0, 68},
- {7, 0, 21, 0, 66},
- {7, 0, 21, 0, 64},
- {7, 0, 21, 0, 63},
- {7, 0, 20, 0, 64},
- {7, 0, 19, 0, 65},
- {7, 0, 19, 0, 64},
- {7, 0, 18, 0, 65},
- {7, 0, 18, 0, 64},
- {7, 0, 17, 0, 65},
- {7, 0, 17, 0, 64},
- {7, 0, 16, 0, 65},
- {7, 0, 16, 0, 64},
- {7, 0, 16, 0, 62},
- {7, 0, 16, 0, 60},
- {7, 0, 16, 0, 58},
- {7, 0, 15, 0, 61},
- {7, 0, 15, 0, 59},
- {7, 0, 14, 0, 61},
- {7, 0, 14, 0, 60},
- {7, 0, 14, 0, 58},
- {7, 0, 13, 0, 60},
- {7, 0, 13, 0, 59},
- {7, 0, 12, 0, 62},
- {7, 0, 12, 0, 60},
- {7, 0, 12, 0, 58},
- {7, 0, 11, 0, 62},
- {7, 0, 11, 0, 60},
- {7, 0, 11, 0, 59},
- {7, 0, 11, 0, 57},
- {7, 0, 10, 0, 61},
- {7, 0, 10, 0, 59},
- {7, 0, 10, 0, 57},
- {7, 0, 9, 0, 62},
- {7, 0, 9, 0, 60},
- {7, 0, 9, 0, 58},
- {7, 0, 9, 0, 57},
- {7, 0, 8, 0, 62},
- {7, 0, 8, 0, 60},
- {7, 0, 8, 0, 58},
- {7, 0, 8, 0, 57},
- {7, 0, 8, 0, 55},
- {7, 0, 7, 0, 61},
+ {15, 0, 31, 0, 72},
+ {15, 0, 31, 0, 70},
+ {15, 0, 31, 0, 68},
+ {15, 0, 30, 0, 68},
+ {15, 0, 29, 0, 69},
+ {15, 0, 28, 0, 69},
+ {15, 0, 27, 0, 70},
+ {15, 0, 26, 0, 70},
+ {15, 0, 25, 0, 71},
+ {15, 0, 24, 0, 72},
+ {15, 0, 23, 0, 73},
+ {15, 0, 23, 0, 71},
+ {15, 0, 22, 0, 72},
+ {15, 0, 21, 0, 73},
+ {15, 0, 21, 0, 71},
+ {15, 0, 21, 0, 69},
+ {15, 0, 21, 0, 67},
+ {15, 0, 21, 0, 65},
+ {15, 0, 21, 0, 63},
+ {15, 0, 20, 0, 65},
+ {15, 0, 19, 0, 66},
+ {15, 0, 19, 0, 64},
+ {15, 0, 18, 0, 66},
+ {15, 0, 18, 0, 64},
+ {15, 0, 17, 0, 66},
+ {15, 0, 17, 0, 64},
+ {15, 0, 16, 0, 66},
+ {15, 0, 16, 0, 64},
+ {15, 0, 16, 0, 62},
+ {15, 0, 16, 0, 61},
+ {15, 0, 16, 0, 59},
+ {15, 0, 15, 0, 61},
+ {15, 0, 15, 0, 59},
+ {15, 0, 14, 0, 62},
+ {15, 0, 14, 0, 60},
+ {15, 0, 14, 0, 58},
+ {15, 0, 13, 0, 61},
+ {15, 0, 13, 0, 59},
+ {15, 0, 12, 0, 62},
+ {15, 0, 12, 0, 61},
+ {15, 0, 12, 0, 59},
+ {15, 0, 11, 0, 62},
+ {15, 0, 11, 0, 61},
+ {15, 0, 11, 0, 59},
+ {15, 0, 11, 0, 57},
+ {15, 0, 10, 0, 61},
+ {15, 0, 10, 0, 59},
+ {15, 0, 10, 0, 58},
+ {15, 0, 9, 0, 62},
+ {15, 0, 9, 0, 61},
+ {15, 0, 9, 0, 59},
+ {15, 0, 9, 0, 57},
+ {15, 0, 8, 0, 62},
+ {15, 0, 8, 0, 61},
+ {15, 0, 8, 0, 59},
+ {15, 0, 8, 0, 57},
+ {15, 0, 8, 0, 56},
+ {15, 0, 8, 0, 54},
+ {15, 0, 8, 0, 53},
+ {15, 0, 8, 0, 51},
+ {15, 0, 8, 0, 50},
+ {7, 0, 7, 0, 69},
+ {7, 0, 7, 0, 67},
+ {7, 0, 7, 0, 65},
+ {7, 0, 7, 0, 64},
+ {7, 0, 7, 0, 62},
{7, 0, 7, 0, 60},
{7, 0, 7, 0, 58},
- {7, 0, 7, 0, 56},
+ {7, 0, 7, 0, 57},
{7, 0, 7, 0, 55},
{7, 0, 6, 0, 62},
- {7, 0, 6, 0, 60},
- {7, 0, 6, 0, 58},
+ {7, 0, 6, 0, 61},
+ {7, 0, 6, 0, 59},
{7, 0, 6, 0, 57},
- {7, 0, 6, 0, 55},
+ {7, 0, 6, 0, 56},
{7, 0, 6, 0, 54},
- {7, 0, 6, 0, 52},
+ {7, 0, 6, 0, 53},
{7, 0, 5, 0, 61},
- {7, 0, 5, 0, 59},
- {7, 0, 5, 0, 57},
+ {7, 0, 5, 0, 60},
+ {7, 0, 5, 0, 58},
{7, 0, 5, 0, 56},
- {7, 0, 5, 0, 54},
+ {7, 0, 5, 0, 55},
{7, 0, 5, 0, 53},
- {7, 0, 5, 0, 51},
- {7, 0, 4, 0, 62},
- {7, 0, 4, 0, 60},
- {7, 0, 4, 0, 58},
+ {7, 0, 5, 0, 52},
+ {7, 0, 5, 0, 50},
+ {7, 0, 5, 0, 49},
+ {7, 0, 5, 0, 47},
{7, 0, 4, 0, 57},
- {7, 0, 4, 0, 55},
+ {7, 0, 4, 0, 56},
{7, 0, 4, 0, 54},
- {7, 0, 4, 0, 52},
+ {7, 0, 4, 0, 53},
{7, 0, 4, 0, 51},
- {7, 0, 4, 0, 49},
+ {7, 0, 4, 0, 50},
{7, 0, 4, 0, 48},
+ {7, 0, 4, 0, 47},
{7, 0, 4, 0, 46},
- {7, 0, 3, 0, 60},
- {7, 0, 3, 0, 58},
- {7, 0, 3, 0, 57},
- {7, 0, 3, 0, 55},
- {7, 0, 3, 0, 54},
- {7, 0, 3, 0, 52},
+ {7, 0, 4, 0, 44},
+ {7, 0, 4, 0, 43},
+ {7, 0, 4, 0, 42},
+ {7, 0, 4, 0, 41},
+ {7, 0, 4, 0, 40},
{7, 0, 3, 0, 51},
- {7, 0, 3, 0, 49},
+ {7, 0, 3, 0, 50},
{7, 0, 3, 0, 48},
+ {7, 0, 3, 0, 47},
{7, 0, 3, 0, 46},
- {7, 0, 3, 0, 45},
{7, 0, 3, 0, 44},
{7, 0, 3, 0, 43},
+ {7, 0, 3, 0, 42},
{7, 0, 3, 0, 41},
- {7, 0, 2, 0, 61},
- {7, 0, 2, 0, 59},
- {7, 0, 2, 0, 57},
- {7, 0, 2, 0, 56},
- {7, 0, 2, 0, 54},
- {7, 0, 2, 0, 53},
- {7, 0, 2, 0, 51},
- {7, 0, 2, 0, 50},
- {7, 0, 2, 0, 48},
- {7, 0, 2, 0, 47},
- {7, 0, 2, 0, 46},
- {7, 0, 2, 0, 44},
- {7, 0, 2, 0, 43},
- {7, 0, 2, 0, 42},
- {7, 0, 2, 0, 41},
- {7, 0, 2, 0, 39},
- {7, 0, 2, 0, 38},
- {7, 0, 2, 0, 37},
- {7, 0, 2, 0, 36},
- {7, 0, 2, 0, 35},
- {7, 0, 2, 0, 34},
- {7, 0, 2, 0, 33},
- {7, 0, 2, 0, 32},
- {7, 0, 1, 0, 63},
- {7, 0, 1, 0, 61},
- {7, 0, 1, 0, 59},
- {7, 0, 1, 0, 57},
+ {3, 0, 3, 0, 56},
+ {3, 0, 3, 0, 54},
+ {3, 0, 3, 0, 53},
+ {3, 0, 3, 0, 51},
+ {3, 0, 3, 0, 50},
+ {3, 0, 3, 0, 48},
+ {3, 0, 3, 0, 47},
+ {3, 0, 3, 0, 46},
+ {3, 0, 3, 0, 44},
+ {3, 0, 3, 0, 43},
+ {3, 0, 3, 0, 42},
+ {3, 0, 3, 0, 41},
+ {3, 0, 3, 0, 39},
+ {3, 0, 3, 0, 38},
+ {3, 0, 3, 0, 37},
+ {3, 0, 3, 0, 36},
+ {3, 0, 3, 0, 35},
+ {3, 0, 3, 0, 34},
};

const struct lcnphy_tx_gain_tbl_entry dot11lcnphy_5GHz_gaintable_rev0[128] = {
--
1.7.10.4



2013-08-22 08:09:01

by Arend van Spriel

[permalink] [raw]
Subject: Re: [RFT V2 02/13] brcmsmac: change pa_gain for bcm4313 iPA

On 08/21/2013 09:18 PM, Hauke Mehrtens wrote:
> Hi Arend,
>
> when you send a new patch please fix this typo.

Got it covered already:

http://mid.gmane.org/[email protected]

Regards,
Arend

> Hauke
>
> On 08/13/2013 10:03 PM, Arend van Spriel wrote:
>> The function wlc_lcnphy_load_tx_gain_table() has a target PA
>> gain specified for the iPA variant of the bcm4313. This gain
>> value is reduced to avoid PA distortion. The if-statement is
>> removed because it was rather redundant in the first place.
>> Please not that this patch does not provide full iPA support.
> ^^^
> note
>
>
>



2013-08-13 20:04:32

by Arend van Spriel

[permalink] [raw]
Subject: [RFT V2 08/13] brcmsmac: fix TSSI idle estimation

The baseband multiplier must be zero during TSSI idle estimation
and restored afterwards.

Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 9 +++++++++
1 file changed, 9 insertions(+)

diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index 8099d74..96be1ba 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -2836,6 +2836,8 @@ static void wlc_lcnphy_idle_tssi_est(struct brcms_phy_pub *ppi)
read_radio_reg(pi, RADIO_2064_REG007) & 1;
u16 SAVE_jtag_auxpga = read_radio_reg(pi, RADIO_2064_REG0FF) & 0x10;
u16 SAVE_iqadc_aux_en = read_radio_reg(pi, RADIO_2064_REG11F) & 4;
+ u8 SAVE_bbmult = wlc_lcnphy_get_bbmult(pi);
+
idleTssi = read_phy_reg(pi, 0x4ab);
suspend = (0 == (bcma_read32(pi->d11core, D11REGOFFS(maccontrol)) &
MCTL_EN_MAC));
@@ -2853,6 +2855,12 @@ static void wlc_lcnphy_idle_tssi_est(struct brcms_phy_pub *ppi)
mod_radio_reg(pi, RADIO_2064_REG0FF, 0x10, 1 << 4);
mod_radio_reg(pi, RADIO_2064_REG11F, 0x4, 1 << 2);
wlc_lcnphy_tssi_setup(pi);
+
+ mod_phy_reg(pi, 0x4d7, (0x1 << 0), (1 << 0));
+ mod_phy_reg(pi, 0x4d7, (0x1 << 6), (1 << 6));
+
+ wlc_lcnphy_set_bbmult(pi, 0x0);
+
wlc_phy_do_dummy_tx(pi, true, OFF);
idleTssi = ((read_phy_reg(pi, 0x4ab) & (0x1ff << 0))
>> 0);
@@ -2874,6 +2882,7 @@ static void wlc_lcnphy_idle_tssi_est(struct brcms_phy_pub *ppi)

mod_phy_reg(pi, 0x44c, (0x1 << 12), (0) << 12);

+ wlc_lcnphy_set_bbmult(pi, SAVE_bbmult);
wlc_lcnphy_set_tx_gain_override(pi, tx_gain_override_old);
wlc_lcnphy_set_tx_gain(pi, &old_gains);
wlc_lcnphy_set_tx_pwr_ctrl(pi, SAVE_txpwrctrl);
--
1.7.10.4



2013-08-13 20:04:32

by Arend van Spriel

[permalink] [raw]
Subject: [RFT V2 11/13] brcmsmac: correct phy registers for TSSI-based power control

A number of additional phy registers needs to be programmed when
using TSSI-based power control.

Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
.../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)

diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index 732371c..a0a268d 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -2020,6 +2020,16 @@ wlc_lcnphy_set_tssi_mux(struct brcms_phy *pi, enum lcnphy_tssi_mode pos)
} else {
mod_radio_reg(pi, RADIO_2064_REG03A, 1, 0x1);
mod_radio_reg(pi, RADIO_2064_REG11A, 0x8, 0x8);
+ mod_radio_reg(pi, RADIO_2064_REG028, 0x1, 0x0);
+ mod_radio_reg(pi, RADIO_2064_REG11A, 0x4, 1<<2);
+ mod_radio_reg(pi, RADIO_2064_REG036, 0x10, 0x0);
+ mod_radio_reg(pi, RADIO_2064_REG11A, 0x10, 1<<4);
+ mod_radio_reg(pi, RADIO_2064_REG036, 0x3, 0x0);
+ mod_radio_reg(pi, RADIO_2064_REG035, 0xff, 0x77);
+ mod_radio_reg(pi, RADIO_2064_REG028, 0x1e, 0xe<<1);
+ mod_radio_reg(pi, RADIO_2064_REG112, 0x80, 1<<7);
+ mod_radio_reg(pi, RADIO_2064_REG005, 0x7, 1<<1);
+ mod_radio_reg(pi, RADIO_2064_REG029, 0xf0, 0<<4);
}
} else {
mod_phy_reg(pi, 0x4d9, (0x1 << 2), (0x1) << 2);
@@ -2106,6 +2116,7 @@ static void wlc_lcnphy_pwrctrl_rssiparams(struct brcms_phy *pi)
(auxpga_vmid_temp << 0) | (auxpga_gain_temp << 12));

mod_radio_reg(pi, RADIO_2064_REG082, (1 << 5), (1 << 5));
+ mod_radio_reg(pi, RADIO_2064_REG07C, (1 << 0), (1 << 0));
}

static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi)
@@ -2218,6 +2229,10 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi)

mod_phy_reg(pi, 0x4d7, (0xf << 8), (0) << 8);

+ mod_radio_reg(pi, RADIO_2064_REG035, 0xff, 0x0);
+ mod_radio_reg(pi, RADIO_2064_REG036, 0x3, 0x0);
+ mod_radio_reg(pi, RADIO_2064_REG11A, 0x8, 0x8);
+
wlc_lcnphy_pwrctrl_rssiparams(pi);
}

@@ -3096,6 +3111,11 @@ static void wlc_lcnphy_tx_pwr_ctrl_init(struct brcms_phy_pub *ppi)
wlc_lcnphy_write_table(pi, &tab);
tab.tbl_offset++;
}
+ mod_phy_reg(pi, 0x4d0, (0x1 << 0), (0) << 0);
+ mod_phy_reg(pi, 0x4d3, (0xff << 0), (0) << 0);
+ mod_phy_reg(pi, 0x4d3, (0xff << 8), (0) << 8);
+ mod_phy_reg(pi, 0x4d0, (0x1 << 4), (0) << 4);
+ mod_phy_reg(pi, 0x4d0, (0x1 << 2), (0) << 2);

mod_phy_reg(pi, 0x410, (0x1 << 7), (0) << 7);

--
1.7.10.4



2013-08-21 19:01:07

by Arend van Spriel

[permalink] [raw]
Subject: Re: [RFT 00/13] brcmsmac: bcm4313 iPA related patches

On 08/21/13 18:17, Maximilian Engelhardt wrote:
> On Tuesday 13 August 2013 22:03:27 Arend van Spriel wrote:
>> This series replaces the patch "[PATCH 12/12] brcmsmac: support 4313iPA"
>> with Message-ID:<[email protected]>.
>>
>> It has been split up into individual patches. Please test this series
>> especially if you had issues with the original commit b6fc28a that was
>> reverted.
>>
>> Cc: Jonas Gorski<[email protected]>
>> Cc: David Herrmann<[email protected]>
>> Cc: Maximilian Engelhardt<[email protected]>
>> Cc: David Costa<[email protected]>
>>
>> Arend van Spriel (13):
>> brcmsmac: cosmetic change in phy_lcn.c
>> brcmsmac: change pa_gain for bcm4313 iPA
>> brcmsmac: use ARRAY_SIZE in phytbl_lcn.c
>> brcmsmac: add switch control table for BCM4313 iPA BT-combo cards
>> brcmsmac: add debug info message providing phy and radio info
>> brcmsmac: update transmit gain table for lcn phy
>> brcmsmac: change lcnphy receive i/q calibration routine
>> brcmsmac: fix TSSI idle estimation
>> brcmsmac: avoid calling set_txpwr_by_index() twice
>> brcmsmac: rework switch control table init including iPA BT-combo
>> brcmsmac: correct phy registers for TSSI-based power control
>> brcmsmac: reinitialize TSSI power control upon channel switch
>> brcmsmac: add support for BCM4313 iPA variant
>>
>> drivers/net/wireless/brcm80211/brcmsmac/main.c | 4 +-
>> .../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 397
>> +++++++++++-------- .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c |
>> 405 +++++++++++--------- .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h
>> | 1 +
>> 4 files changed, 475 insertions(+), 332 deletions(-)
>
> Hello Arend,
>
> I finally had some time to test your patches.
>
> On my hardware I couldn't find any regressions with these patches. I also
> verified that the reception problems I had with my card are fixed by these
> patches.
>
> I did test the patches on top of 3.10.5 as they did apply without any
> problems.

Appreciated. I did send the patches for wireless-next already, ie. for
v3.12 kernel. Good to know that they apply to 3.10 as is.

Regards,
Arend


2013-08-21 19:18:58

by Hauke Mehrtens

[permalink] [raw]
Subject: Re: [RFT V2 02/13] brcmsmac: change pa_gain for bcm4313 iPA

Hi Arend,

when you send a new patch please fix this typo.

Hauke

On 08/13/2013 10:03 PM, Arend van Spriel wrote:
> The function wlc_lcnphy_load_tx_gain_table() has a target PA
> gain specified for the iPA variant of the bcm4313. This gain
> value is reduced to avoid PA distortion. The if-statement is
> removed because it was rather redundant in the first place.
> Please not that this patch does not provide full iPA support.
^^^
note



2013-08-13 20:04:32

by Arend van Spriel

[permalink] [raw]
Subject: [RFT V2 07/13] brcmsmac: change lcnphy receive i/q calibration routine

The gain setting for the test tone of the i/q calibration is
controlled has changed. This gain level needs to be set correctly
before the i/q compensation can be determined.

Cc: Jonas Gorski <[email protected]>
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Reviewed-by: Hante Meuleman <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
.../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 78 +++++++++++++++-----
1 file changed, 58 insertions(+), 20 deletions(-)

diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index 8dc5d0f..8099d74 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -1329,6 +1329,43 @@ static u32 wlc_lcnphy_measure_digital_power(struct brcms_phy *pi, u16 nsamples)
return (iq_est.i_pwr + iq_est.q_pwr) / nsamples;
}

+static bool wlc_lcnphy_rx_iq_cal_gain(struct brcms_phy *pi, u16 biq1_gain,
+ u16 tia_gain, u16 lna2_gain)
+{
+ u32 i_thresh_l, q_thresh_l;
+ u32 i_thresh_h, q_thresh_h;
+ struct lcnphy_iq_est iq_est_h, iq_est_l;
+
+ wlc_lcnphy_set_rx_gain_by_distribution(pi, 0, 0, 0, biq1_gain, tia_gain,
+ lna2_gain, 0);
+
+ wlc_lcnphy_rx_gain_override_enable(pi, true);
+ wlc_lcnphy_start_tx_tone(pi, 2000, (40 >> 1), 0);
+ udelay(500);
+ write_radio_reg(pi, RADIO_2064_REG112, 0);
+ if (!wlc_lcnphy_rx_iq_est(pi, 1024, 32, &iq_est_l))
+ return false;
+
+ wlc_lcnphy_start_tx_tone(pi, 2000, 40, 0);
+ udelay(500);
+ write_radio_reg(pi, RADIO_2064_REG112, 0);
+ if (!wlc_lcnphy_rx_iq_est(pi, 1024, 32, &iq_est_h))
+ return false;
+
+ i_thresh_l = (iq_est_l.i_pwr << 1);
+ i_thresh_h = (iq_est_l.i_pwr << 2) + iq_est_l.i_pwr;
+
+ q_thresh_l = (iq_est_l.q_pwr << 1);
+ q_thresh_h = (iq_est_l.q_pwr << 2) + iq_est_l.q_pwr;
+ if ((iq_est_h.i_pwr > i_thresh_l) &&
+ (iq_est_h.i_pwr < i_thresh_h) &&
+ (iq_est_h.q_pwr > q_thresh_l) &&
+ (iq_est_h.q_pwr < q_thresh_h))
+ return true;
+
+ return false;
+}
+
static bool
wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi,
const struct lcnphy_rx_iqcomp *iqcomp,
@@ -1343,8 +1380,8 @@ wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi,
RFOverrideVal0_old, rfoverride2_old, rfoverride2val_old,
rfoverride3_old, rfoverride3val_old, rfoverride4_old,
rfoverride4val_old, afectrlovr_old, afectrlovrval_old;
- int tia_gain;
- u32 received_power, rx_pwr_threshold;
+ int tia_gain, lna2_gain, biq1_gain;
+ bool set_gain;
u16 old_sslpnCalibClkEnCtrl, old_sslpnRxFeClkEnCtrl;
u16 values_to_save[11];
s16 *ptr;
@@ -1432,29 +1469,30 @@ wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi,
mod_phy_reg(pi, 0x43b, (0x1 << 0), 1 << 0);
mod_phy_reg(pi, 0x43c, (0x1 << 0), 0 << 0);

- wlc_lcnphy_start_tx_tone(pi, 2000, 120, 0);
write_phy_reg(pi, 0x6da, 0xffff);
or_phy_reg(pi, 0x6db, 0x3);
- wlc_lcnphy_set_trsw_override(pi, tx_switch, rx_switch);
- wlc_lcnphy_rx_gain_override_enable(pi, true);
-
- tia_gain = 8;
- rx_pwr_threshold = 950;
- while (tia_gain > 0) {
- tia_gain -= 1;
- wlc_lcnphy_set_rx_gain_by_distribution(pi,
- 0, 0, 2, 2,
- (u16)
- tia_gain, 1, 0);
- udelay(500);

- received_power =
- wlc_lcnphy_measure_digital_power(pi, 2000);
- if (received_power < rx_pwr_threshold)
- break;
+ wlc_lcnphy_set_trsw_override(pi, tx_switch, rx_switch);
+ for (lna2_gain = 3; lna2_gain >= 0; lna2_gain--) {
+ for (tia_gain = 4; tia_gain >= 0; tia_gain--) {
+ for (biq1_gain = 6; biq1_gain >= 0; biq1_gain--) {
+ set_gain = wlc_lcnphy_rx_iq_cal_gain(pi,
+ (u16)
+ biq1_gain,
+ (u16)
+ tia_gain,
+ (u16)
+ lna2_gain);
+ if (set_gain) {
+ result = wlc_lcnphy_calc_rx_iq_comp(pi,
+ 1024);
+ goto stop_tone;
+ }
+ }
+ }
}
- result = wlc_lcnphy_calc_rx_iq_comp(pi, 0xffff);

+stop_tone:
wlc_lcnphy_stop_tx_tone(pi);

write_phy_reg(pi, 0x631, Core1TxControl_old);
--
1.7.10.4



2013-08-13 20:04:32

by Arend van Spriel

[permalink] [raw]
Subject: [RFT V2 09/13] brcmsmac: avoid calling set_txpwr_by_index() twice

For lcnphy revision 1 or when hardware supports i/q calibration the
function wlc_lcnphy_set_txpwr_by_index() was called twice.

Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
index 96be1ba..e02729d 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -3897,7 +3897,6 @@ static void wlc_lcnphy_txpwrtbl_iqlo_cal(struct brcms_phy *pi)
target_gains.pad_gain = 21;
target_gains.dac_gain = 0;
wlc_lcnphy_set_tx_gain(pi, &target_gains);
- wlc_lcnphy_set_tx_pwr_by_index(pi, 16);

if (LCNREV_IS(pi->pubpi.phy_rev, 1) || pi_lcn->lcnphy_hw_iqcal_en) {

@@ -3908,6 +3907,7 @@ static void wlc_lcnphy_txpwrtbl_iqlo_cal(struct brcms_phy *pi)
lcnphy_recal ? LCNPHY_CAL_RECAL :
LCNPHY_CAL_FULL), false);
} else {
+ wlc_lcnphy_set_tx_pwr_by_index(pi, 16);
wlc_lcnphy_tx_iqlo_soft_cal_full(pi);
}

--
1.7.10.4



2013-08-13 20:46:53

by Arend van Spriel

[permalink] [raw]
Subject: Re: [RFT 00/13] brcmsmac: bcm4313 iPA related patches

On 08/13/2013 10:09 PM, David Herrmann wrote:
> Hi
>
> On Tue, Aug 13, 2013 at 10:03 PM, Arend van Spriel <[email protected]> wrote:
>> This series replaces the patch "[PATCH 12/12] brcmsmac: support 4313iPA"
>> with Message-ID: <[email protected]>.
>>
>> It has been split up into individual patches. Please test this series
>> especially if you had issues with the original commit b6fc28a that was
>> reverted.
>>
>> Cc: Jonas Gorski <[email protected]>
>> Cc: David Herrmann <[email protected]>
>> Cc: Maximilian Engelhardt <[email protected]>
>> Cc: David Costa <[email protected]>
>
> Is this available in a public branch that I can merge? And what should
> be used as base? 3.11-rc5? linux-next?

Indeed I should have mentioned. It applies on v3.11-rc5 for sure. Did
not try linux-next.

Regards,
Arend

> Cheers
> David
>
>> Arend van Spriel (13):
>> brcmsmac: cosmetic change in phy_lcn.c
>> brcmsmac: change pa_gain for bcm4313 iPA
>> brcmsmac: use ARRAY_SIZE in phytbl_lcn.c
>> brcmsmac: add switch control table for BCM4313 iPA BT-combo cards
>> brcmsmac: add debug info message providing phy and radio info
>> brcmsmac: update transmit gain table for lcn phy
>> brcmsmac: change lcnphy receive i/q calibration routine
>> brcmsmac: fix TSSI idle estimation
>> brcmsmac: avoid calling set_txpwr_by_index() twice
>> brcmsmac: rework switch control table init including iPA BT-combo
>> brcmsmac: correct phy registers for TSSI-based power control
>> brcmsmac: reinitialize TSSI power control upon channel switch
>> brcmsmac: add support for BCM4313 iPA variant
>>
>> drivers/net/wireless/brcm80211/brcmsmac/main.c | 4 +-
>> .../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 397 +++++++++++--------
>> .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c | 405 +++++++++++---------
>> .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h | 1 +
>> 4 files changed, 475 insertions(+), 332 deletions(-)
>>
>> --
>> 1.7.10.4
>>
>>
>



2013-08-13 20:04:32

by Arend van Spriel

[permalink] [raw]
Subject: [RFT V2 05/13] brcmsmac: add debug info message providing phy and radio info

For debug purposes it is good to have the phy and radio information
available in the log. Only logged when driver is build when BRCMDBG
or BRCM_TRACING kconfig are set.

Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
drivers/net/wireless/brcm80211/brcmsmac/main.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/brcm80211/brcmsmac/main.c b/drivers/net/wireless/brcm80211/brcmsmac/main.c
index 7ca10bf..c3c6123 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/main.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/main.c
@@ -4652,7 +4652,9 @@ static int brcms_b_attach(struct brcms_c_info *wlc, struct bcma_device *core,
wlc->band->phyrev = wlc_hw->band->phyrev;
wlc->band->radioid = wlc_hw->band->radioid;
wlc->band->radiorev = wlc_hw->band->radiorev;
-
+ brcms_dbg_info(core, "wl%d: phy %u/%u radio %x/%u\n", unit,
+ wlc->band->phytype, wlc->band->phyrev,
+ wlc->band->radioid, wlc->band->radiorev);
/* default contention windows size limits */
wlc_hw->band->CWmin = APHY_CWMIN;
wlc_hw->band->CWmax = PHY_CWMAX;
--
1.7.10.4



2013-08-13 20:04:34

by Arend van Spriel

[permalink] [raw]
Subject: [RFT V2 03/13] brcmsmac: use ARRAY_SIZE in phytbl_lcn.c

This patch converts all sizeof(x)/sizeof(x[0]) instances to
ARRAY_SIZE macro in phytbl_lcn.c. The patch was made using
spatch with ARRAY_SIZE.cocci (see [1]).

[1] https://github.com/coccinelle/coccinelle/tree/master/demos/janitorings

Cc: Jonas Gorski <[email protected]>
Cc: David Herrmann <[email protected]>
Cc: Maximilian Engelhardt <[email protected]>
Cc: David Costa <[email protected]>
Reviewed-by: Hante Meuleman <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
---
.../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c | 117 ++++++++------------
1 file changed, 44 insertions(+), 73 deletions(-)

diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
index 622c01c..deae3a7 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
@@ -1507,117 +1507,103 @@ static const u32 dot11lcn_gain_tbl_5G[] = {

const struct phytbl_info dot11lcnphytbl_rx_gain_info_rev0[] = {
{&dot11lcn_gain_tbl_rev0,
- sizeof(dot11lcn_gain_tbl_rev0) / sizeof(dot11lcn_gain_tbl_rev0[0]), 18,
+ ARRAY_SIZE(dot11lcn_gain_tbl_rev0), 18,
0, 32}
,
{&dot11lcn_aux_gain_idx_tbl_rev0,
- sizeof(dot11lcn_aux_gain_idx_tbl_rev0) /
- sizeof(dot11lcn_aux_gain_idx_tbl_rev0[0]), 14, 0, 16}
+ ARRAY_SIZE(dot11lcn_aux_gain_idx_tbl_rev0), 14, 0, 16}
,
{&dot11lcn_gain_idx_tbl_rev0,
- sizeof(dot11lcn_gain_idx_tbl_rev0) /
- sizeof(dot11lcn_gain_idx_tbl_rev0[0]), 13, 0, 32}
+ ARRAY_SIZE(dot11lcn_gain_idx_tbl_rev0), 13, 0, 32}
,
};

static const struct phytbl_info dot11lcnphytbl_rx_gain_info_rev1[] = {
{&dot11lcn_gain_tbl_rev1,
- sizeof(dot11lcn_gain_tbl_rev1) / sizeof(dot11lcn_gain_tbl_rev1[0]), 18,
+ ARRAY_SIZE(dot11lcn_gain_tbl_rev1), 18,
0, 32}
,
{&dot11lcn_aux_gain_idx_tbl_rev0,
- sizeof(dot11lcn_aux_gain_idx_tbl_rev0) /
- sizeof(dot11lcn_aux_gain_idx_tbl_rev0[0]), 14, 0, 16}
+ ARRAY_SIZE(dot11lcn_aux_gain_idx_tbl_rev0), 14, 0, 16}
,
{&dot11lcn_gain_idx_tbl_rev0,
- sizeof(dot11lcn_gain_idx_tbl_rev0) /
- sizeof(dot11lcn_gain_idx_tbl_rev0[0]), 13, 0, 32}
+ ARRAY_SIZE(dot11lcn_gain_idx_tbl_rev0), 13, 0, 32}
,
};

const struct phytbl_info dot11lcnphytbl_rx_gain_info_2G_rev2[] = {
{&dot11lcn_gain_tbl_2G,
- sizeof(dot11lcn_gain_tbl_2G) / sizeof(dot11lcn_gain_tbl_2G[0]), 18, 0,
+ ARRAY_SIZE(dot11lcn_gain_tbl_2G), 18, 0,
32}
,
{&dot11lcn_aux_gain_idx_tbl_2G,
- sizeof(dot11lcn_aux_gain_idx_tbl_2G) /
- sizeof(dot11lcn_aux_gain_idx_tbl_2G[0]), 14, 0, 16}
+ ARRAY_SIZE(dot11lcn_aux_gain_idx_tbl_2G), 14, 0, 16}
,
{&dot11lcn_gain_idx_tbl_2G,
- sizeof(dot11lcn_gain_idx_tbl_2G) / sizeof(dot11lcn_gain_idx_tbl_2G[0]),
+ ARRAY_SIZE(dot11lcn_gain_idx_tbl_2G),
13, 0, 32}
,
{&dot11lcn_gain_val_tbl_2G,
- sizeof(dot11lcn_gain_val_tbl_2G) / sizeof(dot11lcn_gain_val_tbl_2G[0]),
+ ARRAY_SIZE(dot11lcn_gain_val_tbl_2G),
17, 0, 8}
};

const struct phytbl_info dot11lcnphytbl_rx_gain_info_5G_rev2[] = {
{&dot11lcn_gain_tbl_5G,
- sizeof(dot11lcn_gain_tbl_5G) / sizeof(dot11lcn_gain_tbl_5G[0]), 18, 0,
+ ARRAY_SIZE(dot11lcn_gain_tbl_5G), 18, 0,
32}
,
{&dot11lcn_aux_gain_idx_tbl_5G,
- sizeof(dot11lcn_aux_gain_idx_tbl_5G) /
- sizeof(dot11lcn_aux_gain_idx_tbl_5G[0]), 14, 0, 16}
+ ARRAY_SIZE(dot11lcn_aux_gain_idx_tbl_5G), 14, 0, 16}
,
{&dot11lcn_gain_idx_tbl_5G,
- sizeof(dot11lcn_gain_idx_tbl_5G) / sizeof(dot11lcn_gain_idx_tbl_5G[0]),
+ ARRAY_SIZE(dot11lcn_gain_idx_tbl_5G),
13, 0, 32}
,
{&dot11lcn_gain_val_tbl_5G,
- sizeof(dot11lcn_gain_val_tbl_5G) / sizeof(dot11lcn_gain_val_tbl_5G[0]),
+ ARRAY_SIZE(dot11lcn_gain_val_tbl_5G),
17, 0, 8}
};

const struct phytbl_info dot11lcnphytbl_rx_gain_info_extlna_2G_rev2[] = {
{&dot11lcn_gain_tbl_extlna_2G,
- sizeof(dot11lcn_gain_tbl_extlna_2G) /
- sizeof(dot11lcn_gain_tbl_extlna_2G[0]), 18, 0, 32}
+ ARRAY_SIZE(dot11lcn_gain_tbl_extlna_2G), 18, 0, 32}
,
{&dot11lcn_aux_gain_idx_tbl_extlna_2G,
- sizeof(dot11lcn_aux_gain_idx_tbl_extlna_2G) /
- sizeof(dot11lcn_aux_gain_idx_tbl_extlna_2G[0]), 14, 0, 16}
+ ARRAY_SIZE(dot11lcn_aux_gain_idx_tbl_extlna_2G), 14, 0, 16}
,
{&dot11lcn_gain_idx_tbl_extlna_2G,
- sizeof(dot11lcn_gain_idx_tbl_extlna_2G) /
- sizeof(dot11lcn_gain_idx_tbl_extlna_2G[0]), 13, 0, 32}
+ ARRAY_SIZE(dot11lcn_gain_idx_tbl_extlna_2G), 13, 0, 32}
,
{&dot11lcn_gain_val_tbl_extlna_2G,
- sizeof(dot11lcn_gain_val_tbl_extlna_2G) /
- sizeof(dot11lcn_gain_val_tbl_extlna_2G[0]), 17, 0, 8}
+ ARRAY_SIZE(dot11lcn_gain_val_tbl_extlna_2G), 17, 0, 8}
};

const struct phytbl_info dot11lcnphytbl_rx_gain_info_extlna_5G_rev2[] = {
{&dot11lcn_gain_tbl_5G,
- sizeof(dot11lcn_gain_tbl_5G) / sizeof(dot11lcn_gain_tbl_5G[0]), 18, 0,
+ ARRAY_SIZE(dot11lcn_gain_tbl_5G), 18, 0,
32}
,
{&dot11lcn_aux_gain_idx_tbl_5G,
- sizeof(dot11lcn_aux_gain_idx_tbl_5G) /
- sizeof(dot11lcn_aux_gain_idx_tbl_5G[0]), 14, 0, 16}
+ ARRAY_SIZE(dot11lcn_aux_gain_idx_tbl_5G), 14, 0, 16}
,
{&dot11lcn_gain_idx_tbl_5G,
- sizeof(dot11lcn_gain_idx_tbl_5G) / sizeof(dot11lcn_gain_idx_tbl_5G[0]),
+ ARRAY_SIZE(dot11lcn_gain_idx_tbl_5G),
13, 0, 32}
,
{&dot11lcn_gain_val_tbl_5G,
- sizeof(dot11lcn_gain_val_tbl_5G) / sizeof(dot11lcn_gain_val_tbl_5G[0]),
+ ARRAY_SIZE(dot11lcn_gain_val_tbl_5G),
17, 0, 8}
};

const u32 dot11lcnphytbl_rx_gain_info_sz_rev0 =
- sizeof(dot11lcnphytbl_rx_gain_info_rev0) /
- sizeof(dot11lcnphytbl_rx_gain_info_rev0[0]);
+ ARRAY_SIZE(dot11lcnphytbl_rx_gain_info_rev0);

const u32 dot11lcnphytbl_rx_gain_info_2G_rev2_sz =
- sizeof(dot11lcnphytbl_rx_gain_info_2G_rev2) /
- sizeof(dot11lcnphytbl_rx_gain_info_2G_rev2[0]);
+ ARRAY_SIZE(dot11lcnphytbl_rx_gain_info_2G_rev2);

const u32 dot11lcnphytbl_rx_gain_info_5G_rev2_sz =
- sizeof(dot11lcnphytbl_rx_gain_info_5G_rev2) /
- sizeof(dot11lcnphytbl_rx_gain_info_5G_rev2[0]);
+ ARRAY_SIZE(dot11lcnphytbl_rx_gain_info_5G_rev2);

static const u16 dot11lcn_min_sig_sq_tbl_rev0[] = {
0x014d,
@@ -2771,89 +2757,74 @@ static const u32 dot11lcn_papd_compdelta_tbl_rev0[] = {

const struct phytbl_info dot11lcnphytbl_info_rev0[] = {
{&dot11lcn_min_sig_sq_tbl_rev0,
- sizeof(dot11lcn_min_sig_sq_tbl_rev0) /
- sizeof(dot11lcn_min_sig_sq_tbl_rev0[0]), 2, 0, 16}
+ ARRAY_SIZE(dot11lcn_min_sig_sq_tbl_rev0), 2, 0, 16}
,
{&dot11lcn_noise_scale_tbl_rev0,
- sizeof(dot11lcn_noise_scale_tbl_rev0) /
- sizeof(dot11lcn_noise_scale_tbl_rev0[0]), 1, 0, 16}
+ ARRAY_SIZE(dot11lcn_noise_scale_tbl_rev0), 1, 0, 16}
,
{&dot11lcn_fltr_ctrl_tbl_rev0,
- sizeof(dot11lcn_fltr_ctrl_tbl_rev0) /
- sizeof(dot11lcn_fltr_ctrl_tbl_rev0[0]), 11, 0, 32}
+ ARRAY_SIZE(dot11lcn_fltr_ctrl_tbl_rev0), 11, 0, 32}
,
{&dot11lcn_ps_ctrl_tbl_rev0,
- sizeof(dot11lcn_ps_ctrl_tbl_rev0) /
- sizeof(dot11lcn_ps_ctrl_tbl_rev0[0]), 12, 0, 32}
+ ARRAY_SIZE(dot11lcn_ps_ctrl_tbl_rev0), 12, 0, 32}
,
{&dot11lcn_gain_idx_tbl_rev0,
- sizeof(dot11lcn_gain_idx_tbl_rev0) /
- sizeof(dot11lcn_gain_idx_tbl_rev0[0]), 13, 0, 32}
+ ARRAY_SIZE(dot11lcn_gain_idx_tbl_rev0), 13, 0, 32}
,
{&dot11lcn_aux_gain_idx_tbl_rev0,
- sizeof(dot11lcn_aux_gain_idx_tbl_rev0) /
- sizeof(dot11lcn_aux_gain_idx_tbl_rev0[0]), 14, 0, 16}
+ ARRAY_SIZE(dot11lcn_aux_gain_idx_tbl_rev0), 14, 0, 16}
,
{&dot11lcn_sw_ctrl_tbl_rev0,
- sizeof(dot11lcn_sw_ctrl_tbl_rev0) /
- sizeof(dot11lcn_sw_ctrl_tbl_rev0[0]), 15, 0, 16}
+ ARRAY_SIZE(dot11lcn_sw_ctrl_tbl_rev0), 15, 0, 16}
,
{&dot11lcn_nf_table_rev0,
- sizeof(dot11lcn_nf_table_rev0) / sizeof(dot11lcn_nf_table_rev0[0]), 16,
+ ARRAY_SIZE(dot11lcn_nf_table_rev0), 16,
0, 8}
,
{&dot11lcn_gain_val_tbl_rev0,
- sizeof(dot11lcn_gain_val_tbl_rev0) /
- sizeof(dot11lcn_gain_val_tbl_rev0[0]), 17, 0, 8}
+ ARRAY_SIZE(dot11lcn_gain_val_tbl_rev0), 17, 0, 8}
,
{&dot11lcn_gain_tbl_rev0,
- sizeof(dot11lcn_gain_tbl_rev0) / sizeof(dot11lcn_gain_tbl_rev0[0]), 18,
+ ARRAY_SIZE(dot11lcn_gain_tbl_rev0), 18,
0, 32}
,
{&dot11lcn_spur_tbl_rev0,
- sizeof(dot11lcn_spur_tbl_rev0) / sizeof(dot11lcn_spur_tbl_rev0[0]), 20,
+ ARRAY_SIZE(dot11lcn_spur_tbl_rev0), 20,
0, 8}
,
{&dot11lcn_unsup_mcs_tbl_rev0,
- sizeof(dot11lcn_unsup_mcs_tbl_rev0) /
- sizeof(dot11lcn_unsup_mcs_tbl_rev0[0]), 23, 0, 16}
+ ARRAY_SIZE(dot11lcn_unsup_mcs_tbl_rev0), 23, 0, 16}
,
{&dot11lcn_iq_local_tbl_rev0,
- sizeof(dot11lcn_iq_local_tbl_rev0) /
- sizeof(dot11lcn_iq_local_tbl_rev0[0]), 0, 0, 16}
+ ARRAY_SIZE(dot11lcn_iq_local_tbl_rev0), 0, 0, 16}
,
{&dot11lcn_papd_compdelta_tbl_rev0,
- sizeof(dot11lcn_papd_compdelta_tbl_rev0) /
- sizeof(dot11lcn_papd_compdelta_tbl_rev0[0]), 24, 0, 32}
+ ARRAY_SIZE(dot11lcn_papd_compdelta_tbl_rev0), 24, 0, 32}
,
};

const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313 = {
&dot11lcn_sw_ctrl_tbl_4313_rev0,
- sizeof(dot11lcn_sw_ctrl_tbl_4313_rev0) /
- sizeof(dot11lcn_sw_ctrl_tbl_4313_rev0[0]), 15, 0, 16
+ ARRAY_SIZE(dot11lcn_sw_ctrl_tbl_4313_rev0), 15, 0, 16
};

const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_epa = {
&dot11lcn_sw_ctrl_tbl_4313_epa_rev0,
- sizeof(dot11lcn_sw_ctrl_tbl_4313_epa_rev0) /
- sizeof(dot11lcn_sw_ctrl_tbl_4313_epa_rev0[0]), 15, 0, 16
+ ARRAY_SIZE(dot11lcn_sw_ctrl_tbl_4313_epa_rev0), 15, 0, 16
};

const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_bt_epa = {
&dot11lcn_sw_ctrl_tbl_4313_epa_rev0_combo,
- sizeof(dot11lcn_sw_ctrl_tbl_4313_epa_rev0_combo) /
- sizeof(dot11lcn_sw_ctrl_tbl_4313_epa_rev0_combo[0]), 15, 0, 16
+ ARRAY_SIZE(dot11lcn_sw_ctrl_tbl_4313_epa_rev0_combo), 15, 0, 16
};

const struct phytbl_info dot11lcn_sw_ctrl_tbl_info_4313_bt_epa_p250 = {
&dot11lcn_sw_ctrl_tbl_4313_bt_epa_p250_rev0,
- sizeof(dot11lcn_sw_ctrl_tbl_4313_bt_epa_p250_rev0) /
- sizeof(dot11lcn_sw_ctrl_tbl_4313_bt_epa_p250_rev0[0]), 15, 0, 16
+ ARRAY_SIZE(dot11lcn_sw_ctrl_tbl_4313_bt_epa_p250_rev0), 15, 0, 16
};

const u32 dot11lcnphytbl_info_sz_rev0 =
- sizeof(dot11lcnphytbl_info_rev0) / sizeof(dot11lcnphytbl_info_rev0[0]);
+ ARRAY_SIZE(dot11lcnphytbl_info_rev0);

const struct lcnphy_tx_gain_tbl_entry
dot11lcnphy_2GHz_extPA_gaintable_rev0[128] = {
--
1.7.10.4



2013-08-21 16:28:17

by Maximilian Engelhardt

[permalink] [raw]
Subject: Re: [RFT 00/13] brcmsmac: bcm4313 iPA related patches

On Tuesday 13 August 2013 22:03:27 Arend van Spriel wrote:
> This series replaces the patch "[PATCH 12/12] brcmsmac: support 4313iPA"
> with Message-ID: <[email protected]>.
>
> It has been split up into individual patches. Please test this series
> especially if you had issues with the original commit b6fc28a that was
> reverted.
>
> Cc: Jonas Gorski <[email protected]>
> Cc: David Herrmann <[email protected]>
> Cc: Maximilian Engelhardt <[email protected]>
> Cc: David Costa <[email protected]>
>
> Arend van Spriel (13):
> brcmsmac: cosmetic change in phy_lcn.c
> brcmsmac: change pa_gain for bcm4313 iPA
> brcmsmac: use ARRAY_SIZE in phytbl_lcn.c
> brcmsmac: add switch control table for BCM4313 iPA BT-combo cards
> brcmsmac: add debug info message providing phy and radio info
> brcmsmac: update transmit gain table for lcn phy
> brcmsmac: change lcnphy receive i/q calibration routine
> brcmsmac: fix TSSI idle estimation
> brcmsmac: avoid calling set_txpwr_by_index() twice
> brcmsmac: rework switch control table init including iPA BT-combo
> brcmsmac: correct phy registers for TSSI-based power control
> brcmsmac: reinitialize TSSI power control upon channel switch
> brcmsmac: add support for BCM4313 iPA variant
>
> drivers/net/wireless/brcm80211/brcmsmac/main.c | 4 +-
> .../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 397
> +++++++++++-------- .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c |
> 405 +++++++++++--------- .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.h
> | 1 +
> 4 files changed, 475 insertions(+), 332 deletions(-)

Hello Arend,

I finally had some time to test your patches.

On my hardware I couldn't find any regressions with these patches. I also
verified that the reception problems I had with my card are fixed by these
patches.

I did test the patches on top of 3.10.5 as they did apply without any
problems.

Greetings,
Maxi


Attachments:
signature.asc (836.00 B)
This is a digitally signed message part.