This support is compiled in if CONFIG_RFKILL
option is set.
Signed-off-by: Vasanthakumar Thiagarajan <[email protected]>
---
drivers/net/wireless/ath9k/Kconfig | 1 +
drivers/net/wireless/ath9k/ath9k.h | 9 +-
drivers/net/wireless/ath9k/core.h | 24 +
drivers/net/wireless/ath9k/hw.c | 70 ++-
drivers/net/wireless/ath9k/hw.h | 2 -
drivers/net/wireless/ath9k/main.c | 1205 ++++++++++++++++++++++--------------
6 files changed, 808 insertions(+), 503 deletions(-)
diff --git a/drivers/net/wireless/ath9k/Kconfig b/drivers/net/wireless/ath9k/Kconfig
index 80a6924..9358e9a 100644
--- a/drivers/net/wireless/ath9k/Kconfig
+++ b/drivers/net/wireless/ath9k/Kconfig
@@ -4,6 +4,7 @@ config ATH9K
select MAC80211_LEDS
select LEDS_CLASS
select NEW_LEDS
+ select RFKILL
---help---
This module adds support for wireless adapters based on
Atheros IEEE 802.11n AR5008 and AR9001 family of chipsets.
diff --git a/drivers/net/wireless/ath9k/ath9k.h b/drivers/net/wireless/ath9k/ath9k.h
index 28b8d84..d92e1ed 100644
--- a/drivers/net/wireless/ath9k/ath9k.h
+++ b/drivers/net/wireless/ath9k/ath9k.h
@@ -798,10 +798,13 @@ struct ath_hal {
struct ath9k_channel *ah_curchan;
u32 ah_nchan;
- u16 ah_rfsilent;
- bool ah_rfkillEnabled;
bool ah_isPciExpress;
u16 ah_txTrigLevel;
+#ifdef CONFIG_RFKILL
+ u16 ah_rfsilent;
+ u32 ah_rfkill_gpio ;
+ u32 ah_rfkill_polarity;
+#endif
#ifndef ATH_NF_PER_CHAN
struct ath9k_nfcal_hist nfCalHist[NUM_NF_READINGS];
@@ -1003,4 +1006,6 @@ bool ath9k_get_channel_edges(struct ath_hal *ah,
void ath9k_hw_cfg_output(struct ath_hal *ah, u32 gpio,
u32 ah_signal_type);
void ath9k_hw_set_gpio(struct ath_hal *ah, u32 gpio, u32 value);
+u32 ath9k_hw_gpio_get(struct ath_hal *ah, u32 gpio);
+void ath9k_hw_cfg_gpio_input(struct ath_hal *ah, u32 gpio);
#endif
diff --git a/drivers/net/wireless/ath9k/core.h b/drivers/net/wireless/ath9k/core.h
index 1faa1ef..aae5a4f 100644
--- a/drivers/net/wireless/ath9k/core.h
+++ b/drivers/net/wireless/ath9k/core.h
@@ -40,6 +40,9 @@
#include <asm/page.h>
#include <net/mac80211.h>
#include <linux/leds.h>
+#ifdef CONFIG_RFKILL
+#include <linux/rfkill.h>
+#endif
#include "ath9k.h"
#include "rc.h"
@@ -823,6 +826,17 @@ struct ath_led {
bool registered;
};
+#ifdef CONFIG_RFKILL
+/* Rfkill */
+#define ATH_RFKILL_POLL_INTERVAL 2000 /* msecs */
+
+struct ath_rfkill {
+ struct rfkill *rfkill;
+ struct delayed_work rfkill_poll;
+ char rfkill_name[32];
+};
+#endif
+
/********************/
/* Main driver core */
/********************/
@@ -906,6 +920,11 @@ struct ath_ht_info {
#define SC_OP_PROTECT_ENABLE BIT(8)
#define SC_OP_RXFLUSH BIT(9)
#define SC_OP_LED_ASSOCIATED BIT(10)
+#ifdef CONFIG_RFKILL
+#define SC_OP_RFKILL_REGISTERED BIT(11)
+#define SC_OP_RFKILL_SW_BLOCKED BIT(12)
+#define SC_OP_RFKILL_HW_BLOCKED BIT(13)
+#endif
struct ath_softc {
struct ieee80211_hw *hw;
@@ -1015,6 +1034,11 @@ struct ath_softc {
struct ath_led assoc_led;
struct ath_led tx_led;
struct ath_led rx_led;
+
+#ifdef CONFIG_RFKILL
+ /* Rfkill */
+ struct ath_rfkill rf_kill;
+#endif
};
int ath_init(u16 devid, struct ath_softc *sc);
diff --git a/drivers/net/wireless/ath9k/hw.c b/drivers/net/wireless/ath9k/hw.c
index 4ccbbc0..0251e59 100644
--- a/drivers/net/wireless/ath9k/hw.c
+++ b/drivers/net/wireless/ath9k/hw.c
@@ -2821,7 +2821,38 @@ void ath9k_hw_set_gpio(struct ath_hal *ah, u32 gpio, u32 val)
AR_GPIO_BIT(gpio));
}
-static u32 ath9k_hw_gpio_get(struct ath_hal *ah, u32 gpio)
+/*
+ * Configure GPIO Input lines
+ */
+void ath9k_hw_cfg_gpio_input(struct ath_hal *ah, u32 gpio)
+{
+ u32 gpio_shift;
+
+ ASSERT(gpio < ah->ah_caps.num_gpio_pins);
+
+ gpio_shift = gpio << 1;
+
+ REG_RMW(ah,
+ AR_GPIO_OE_OUT,
+ (AR_GPIO_OE_OUT_DRV_NO << gpio_shift),
+ (AR_GPIO_OE_OUT_DRV << gpio_shift));
+}
+
+#ifdef CONFIG_RFKILL
+static void ath9k_enable_rfkill(struct ath_hal *ah)
+{
+ REG_SET_BIT(ah, AR_GPIO_INPUT_EN_VAL,
+ AR_GPIO_INPUT_EN_VAL_RFSILENT_BB);
+
+ REG_CLR_BIT(ah, AR_GPIO_INPUT_MUX2,
+ AR_GPIO_INPUT_MUX2_RFSILENT);
+
+ ath9k_hw_cfg_gpio_input(ah, ah->ah_rfkill_gpio);
+ REG_SET_BIT(ah, AR_PHY_TEST, RFSILENT_BB);
+}
+#endif
+
+u32 ath9k_hw_gpio_get(struct ath_hal *ah, u32 gpio)
{
if (gpio >= ah->ah_caps.num_gpio_pins)
return 0xffffffff;
@@ -3034,17 +3065,17 @@ static bool ath9k_hw_fill_cap_info(struct ath_hal *ah)
pCap->hw_caps |= ATH9K_HW_CAP_ENHANCEDPM;
+#ifdef CONFIG_RFKILL
ah->ah_rfsilent = ath9k_hw_get_eeprom(ahp, EEP_RF_SILENT);
if (ah->ah_rfsilent & EEP_RFSILENT_ENABLED) {
- ahp->ah_gpioSelect =
+ ah->ah_rfkill_gpio =
MS(ah->ah_rfsilent, EEP_RFSILENT_GPIO_SEL);
- ahp->ah_polarity =
+ ah->ah_rfkill_polarity =
MS(ah->ah_rfsilent, EEP_RFSILENT_POLARITY);
- ath9k_hw_setcapability(ah, ATH9K_CAP_RFSILENT, 1, true,
- NULL);
pCap->hw_caps |= ATH9K_HW_CAP_RFSILENT;
}
+#endif
if ((ah->ah_macVersion == AR_SREV_VERSION_5416_PCI) ||
(ah->ah_macVersion == AR_SREV_VERSION_5416_PCIE) ||
@@ -5961,6 +5992,10 @@ bool ath9k_hw_reset(struct ath_hal *ah,
ath9k_hw_init_interrupt_masks(ah, ah->ah_opmode);
ath9k_hw_init_qos(ah);
+#ifdef CONFIG_RFKILL
+ if (ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT)
+ ath9k_enable_rfkill(ah);
+#endif
ath9k_hw_init_user_settings(ah);
REG_WRITE(ah, AR_STA_ID1,
@@ -6490,31 +6525,6 @@ ath9k_hw_setbssidmask(struct ath_hal *ah, const u8 *mask)
return true;
}
-#ifdef CONFIG_ATH9K_RFKILL
-static void ath9k_enable_rfkill(struct ath_hal *ah)
-{
- struct ath_hal_5416 *ahp = AH5416(ah);
-
- REG_SET_BIT(ah, AR_GPIO_INPUT_EN_VAL,
- AR_GPIO_INPUT_EN_VAL_RFSILENT_BB);
-
- REG_CLR_BIT(ah, AR_GPIO_INPUT_MUX2,
- AR_GPIO_INPUT_MUX2_RFSILENT);
-
- ath9k_hw_cfg_gpio_input(ah, ahp->ah_gpioSelect);
- REG_SET_BIT(ah, AR_PHY_TEST, RFSILENT_BB);
-
- if (ahp->ah_gpioBit == ath9k_hw_gpio_get(ah, ahp->ah_gpioSelect)) {
-
- ath9k_hw_set_gpio_intr(ah, ahp->ah_gpioSelect,
- !ahp->ah_gpioBit);
- } else {
- ath9k_hw_set_gpio_intr(ah, ahp->ah_gpioSelect,
- ahp->ah_gpioBit);
- }
-}
-#endif
-
void
ath9k_hw_write_associd(struct ath_hal *ah, const u8 *bssid,
u16 assocId)
diff --git a/drivers/net/wireless/ath9k/hw.h b/drivers/net/wireless/ath9k/hw.h
index 2113818..2134838 100644
--- a/drivers/net/wireless/ath9k/hw.h
+++ b/drivers/net/wireless/ath9k/hw.h
@@ -757,8 +757,6 @@ struct ath_hal_5416 {
u32 ah_ctstimeout;
u32 ah_globaltxtimeout;
u8 ah_gBeaconRate;
- u32 ah_gpioSelect;
- u32 ah_polarity;
u32 ah_gpioBit;
/* ANI */
diff --git a/drivers/net/wireless/ath9k/main.c b/drivers/net/wireless/ath9k/main.c
index 57d7cc8..6caecc5 100644
--- a/drivers/net/wireless/ath9k/main.c
+++ b/drivers/net/wireless/ath9k/main.c
@@ -325,6 +325,693 @@ static u8 parse_mpdudensity(u8 mpdudensity)
}
}
+#ifdef CONFIG_RFKILL
+/*******************/
+/* Rfkill */
+/*******************/
+
+static void ath_radio_enable(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ int status;
+
+ spin_lock_bh(&sc->sc_resetlock);
+ if (!ath9k_hw_reset(ah, ah->ah_curchan,
+ sc->sc_ht_info.tx_chan_width,
+ sc->sc_tx_chainmask,
+ sc->sc_rx_chainmask,
+ sc->sc_ht_extprotspacing,
+ false, &status)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to reset channel %u (%uMhz) "
+ "flags 0x%x hal status %u\n", __func__,
+ ath9k_hw_mhz2ieee(ah,
+ ah->ah_curchan->channel,
+ ah->ah_curchan->channelFlags),
+ ah->ah_curchan->channel,
+ ah->ah_curchan->channelFlags, status);
+ }
+ spin_unlock_bh(&sc->sc_resetlock);
+
+ ath_update_txpow(sc);
+ if (ath_startrecv(sc) != 0) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to restart recv logic\n", __func__);
+ return;
+ }
+
+ if (sc->sc_flags & SC_OP_BEACONS)
+ ath_beacon_config(sc, ATH_IF_ID_ANY); /* restart beacons */
+
+ /* Re-Enable interrupts */
+ ath9k_hw_set_interrupts(ah, sc->sc_imask);
+
+ /* Enable LED */
+ ath9k_hw_cfg_output(ah, ATH_LED_PIN,
+ AR_GPIO_OUTPUT_MUX_AS_OUTPUT);
+ ath9k_hw_set_gpio(ah, ATH_LED_PIN, 0);
+
+ ieee80211_wake_queues(sc->hw);
+}
+
+static void ath_radio_disable(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ int status;
+
+
+ ieee80211_stop_queues(sc->hw);
+
+ /* Disable LED */
+ ath9k_hw_set_gpio(ah, ATH_LED_PIN, 1);
+ ath9k_hw_cfg_gpio_input(ah, ATH_LED_PIN);
+
+ /* Disable interrupts */
+ ath9k_hw_set_interrupts(ah, 0);
+
+ ath_draintxq(sc, false); /* clear pending tx frames */
+ ath_stoprecv(sc); /* turn off frame recv */
+ ath_flushrecv(sc); /* flush recv queue */
+
+ spin_lock_bh(&sc->sc_resetlock);
+ if (!ath9k_hw_reset(ah, ah->ah_curchan,
+ sc->sc_ht_info.tx_chan_width,
+ sc->sc_tx_chainmask,
+ sc->sc_rx_chainmask,
+ sc->sc_ht_extprotspacing,
+ false, &status)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to reset channel %u (%uMhz) "
+ "flags 0x%x hal status %u\n", __func__,
+ ath9k_hw_mhz2ieee(ah,
+ ah->ah_curchan->channel,
+ ah->ah_curchan->channelFlags),
+ ah->ah_curchan->channel,
+ ah->ah_curchan->channelFlags, status);
+ }
+ spin_unlock_bh(&sc->sc_resetlock);
+
+ ath9k_hw_phy_disable(ah);
+ ath9k_hw_setpower(ah, ATH9K_PM_FULL_SLEEP);
+}
+
+static bool ath_is_rfkill_set(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+
+ return ath9k_hw_gpio_get(ah, ah->ah_rfkill_gpio) ==
+ ah->ah_rfkill_polarity;
+}
+
+/* h/w rfkill poll function */
+static void ath_rfkill_poll(struct work_struct *work)
+{
+ struct ath_softc *sc = container_of(work, struct ath_softc,
+ rf_kill.rfkill_poll.work);
+ bool radio_on;
+
+ if (sc->sc_flags & SC_OP_INVALID)
+ return;
+
+ radio_on = !ath_is_rfkill_set(sc);
+
+ /*
+ * enable/disable radio only when there is a
+ * state change in RF switch
+ */
+ if (radio_on == !!(sc->sc_flags & SC_OP_RFKILL_HW_BLOCKED)) {
+ enum rfkill_state state;
+
+ if (sc->sc_flags & SC_OP_RFKILL_SW_BLOCKED) {
+ state = radio_on ? RFKILL_STATE_SOFT_BLOCKED
+ : RFKILL_STATE_HARD_BLOCKED;
+ } else if (radio_on) {
+ ath_radio_enable(sc);
+ state = RFKILL_STATE_UNBLOCKED;
+ } else {
+ ath_radio_disable(sc);
+ state = RFKILL_STATE_HARD_BLOCKED;
+ }
+
+ if (state == RFKILL_STATE_HARD_BLOCKED)
+ sc->sc_flags |= SC_OP_RFKILL_HW_BLOCKED;
+ else
+ sc->sc_flags &= ~SC_OP_RFKILL_HW_BLOCKED;
+
+ rfkill_force_state(sc->rf_kill.rfkill, state);
+ }
+
+ queue_delayed_work(sc->hw->workqueue, &sc->rf_kill.rfkill_poll,
+ msecs_to_jiffies(ATH_RFKILL_POLL_INTERVAL));
+}
+
+/* s/w rfkill handler */
+static int ath_sw_toggle_radio(void *data, enum rfkill_state state)
+{
+ struct ath_softc *sc = data;
+
+ switch (state) {
+ case RFKILL_STATE_SOFT_BLOCKED:
+ if (!(sc->sc_flags & (SC_OP_RFKILL_HW_BLOCKED |
+ SC_OP_RFKILL_SW_BLOCKED)))
+ ath_radio_disable(sc);
+ sc->sc_flags |= SC_OP_RFKILL_SW_BLOCKED;
+ return 0;
+ case RFKILL_STATE_UNBLOCKED:
+ if ((sc->sc_flags & SC_OP_RFKILL_SW_BLOCKED)) {
+ sc->sc_flags &= ~SC_OP_RFKILL_SW_BLOCKED;
+ if (sc->sc_flags & SC_OP_RFKILL_HW_BLOCKED) {
+ DPRINTF(sc, ATH_DBG_FATAL, "Can't turn on the"
+ "radio as it is disabled by h/w \n");
+ return -EPERM;
+ }
+ ath_radio_enable(sc);
+ }
+ return 0;
+ default:
+ return -EINVAL;
+ }
+}
+
+/* Init s/w rfkill */
+static int ath_init_sw_rfkill(struct ath_softc *sc)
+{
+ sc->rf_kill.rfkill = rfkill_allocate(wiphy_dev(sc->hw->wiphy),
+ RFKILL_TYPE_WLAN);
+ if (!sc->rf_kill.rfkill) {
+ DPRINTF(sc, ATH_DBG_FATAL, "Failed to allocate rfkill\n");
+ return -ENOMEM;
+ }
+
+ snprintf(sc->rf_kill.rfkill_name, sizeof(sc->rf_kill.rfkill_name),
+ "ath9k-%s:rfkill", wiphy_name(sc->hw->wiphy));
+ sc->rf_kill.rfkill->name = sc->rf_kill.rfkill_name;
+ sc->rf_kill.rfkill->data = sc;
+ sc->rf_kill.rfkill->toggle_radio = ath_sw_toggle_radio;
+ sc->rf_kill.rfkill->state = RFKILL_STATE_UNBLOCKED;
+ sc->rf_kill.rfkill->user_claim_unsupported = 1;
+
+ return 0;
+}
+
+/* Deinitialize rfkill */
+static void ath_deinit_rfkill(struct ath_softc *sc)
+{
+ if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT)
+ cancel_delayed_work_sync(&sc->rf_kill.rfkill_poll);
+
+ if (sc->sc_flags & SC_OP_RFKILL_REGISTERED) {
+ rfkill_unregister(sc->rf_kill.rfkill);
+ sc->sc_flags &= ~SC_OP_RFKILL_REGISTERED;
+ sc->rf_kill.rfkill = NULL;
+ }
+}
+#endif /* CONFIG_RFKILL */
+
+static void ath9k_ht_conf(struct ath_softc *sc,
+ struct ieee80211_bss_conf *bss_conf)
+{
+#define IEEE80211_HT_CAP_40MHZ_INTOLERANT BIT(14)
+ struct ath_ht_info *ht_info = &sc->sc_ht_info;
+
+ if (bss_conf->assoc_ht) {
+ ht_info->ext_chan_offset =
+ bss_conf->ht_bss_conf->bss_cap &
+ IEEE80211_HT_IE_CHA_SEC_OFFSET;
+
+ if (!(bss_conf->ht_conf->cap &
+ IEEE80211_HT_CAP_40MHZ_INTOLERANT) &&
+ (bss_conf->ht_bss_conf->bss_cap &
+ IEEE80211_HT_IE_CHA_WIDTH))
+ ht_info->tx_chan_width = ATH9K_HT_MACMODE_2040;
+ else
+ ht_info->tx_chan_width = ATH9K_HT_MACMODE_20;
+
+ ath9k_hw_set11nmac2040(sc->sc_ah, ht_info->tx_chan_width);
+ ht_info->maxampdu = 1 << (IEEE80211_HTCAP_MAXRXAMPDU_FACTOR +
+ bss_conf->ht_conf->ampdu_factor);
+ ht_info->mpdudensity =
+ parse_mpdudensity(bss_conf->ht_conf->ampdu_density);
+
+ }
+
+#undef IEEE80211_HT_CAP_40MHZ_INTOLERANT
+}
+
+static void ath9k_bss_assoc_info(struct ath_softc *sc,
+ struct ieee80211_bss_conf *bss_conf)
+{
+ struct ieee80211_hw *hw = sc->hw;
+ struct ieee80211_channel *curchan = hw->conf.channel;
+ struct ath_vap *avp;
+ int pos;
+ DECLARE_MAC_BUF(mac);
+
+ if (bss_conf->assoc) {
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Bss Info ASSOC %d\n",
+ __func__,
+ bss_conf->aid);
+
+ avp = sc->sc_vaps[0];
+ if (avp == NULL) {
+ DPRINTF(sc, ATH_DBG_FATAL, "%s: Invalid interface\n",
+ __func__);
+ return;
+ }
+
+ /* New association, store aid */
+ if (avp->av_opmode == ATH9K_M_STA) {
+ sc->sc_curaid = bss_conf->aid;
+ ath9k_hw_write_associd(sc->sc_ah, sc->sc_curbssid,
+ sc->sc_curaid);
+ }
+
+ /* Configure the beacon */
+ ath_beacon_config(sc, 0);
+ sc->sc_flags |= SC_OP_BEACONS;
+
+ /* Reset rssi stats */
+ sc->sc_halstats.ns_avgbrssi = ATH_RSSI_DUMMY_MARKER;
+ sc->sc_halstats.ns_avgrssi = ATH_RSSI_DUMMY_MARKER;
+ sc->sc_halstats.ns_avgtxrssi = ATH_RSSI_DUMMY_MARKER;
+ sc->sc_halstats.ns_avgtxrate = ATH_RATE_DUMMY_MARKER;
+
+ /* Update chainmask */
+ ath_update_chainmask(sc, bss_conf->assoc_ht);
+
+ DPRINTF(sc, ATH_DBG_CONFIG,
+ "%s: bssid %s aid 0x%x\n",
+ __func__,
+ print_mac(mac, sc->sc_curbssid), sc->sc_curaid);
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Set channel: %d MHz\n",
+ __func__,
+ curchan->center_freq);
+
+ pos = ath_get_channel(sc, curchan);
+ if (pos == -1) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Invalid channel\n", __func__);
+ return;
+ }
+
+ if (hw->conf.ht_conf.ht_supported)
+ sc->sc_ah->ah_channels[pos].chanmode =
+ ath_get_extchanmode(sc, curchan);
+ else
+ sc->sc_ah->ah_channels[pos].chanmode =
+ (curchan->band == IEEE80211_BAND_2GHZ) ?
+ CHANNEL_G : CHANNEL_A;
+
+ /* set h/w channel */
+ if (ath_set_channel(sc, &sc->sc_ah->ah_channels[pos]) < 0)
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Unable to set channel\n",
+ __func__);
+
+ ath_rate_newstate(sc, avp);
+ /* Update ratectrl about the new state */
+ ath_rc_node_update(hw, avp->rc_node);
+ } else {
+ DPRINTF(sc, ATH_DBG_CONFIG,
+ "%s: Bss Info DISSOC\n", __func__);
+ sc->sc_curaid = 0;
+ }
+}
+
+void ath_get_beaconconfig(struct ath_softc *sc,
+ int if_id,
+ struct ath_beacon_config *conf)
+{
+ struct ieee80211_hw *hw = sc->hw;
+
+ /* fill in beacon config data */
+
+ conf->beacon_interval = hw->conf.beacon_int;
+ conf->listen_interval = 100;
+ conf->dtim_count = 1;
+ conf->bmiss_timeout = ATH_DEFAULT_BMISS_LIMIT * conf->listen_interval;
+}
+
+void ath_tx_complete(struct ath_softc *sc, struct sk_buff *skb,
+ struct ath_xmit_status *tx_status, struct ath_node *an)
+{
+ struct ieee80211_hw *hw = sc->hw;
+ struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
+
+ DPRINTF(sc, ATH_DBG_XMIT,
+ "%s: TX complete: skb: %p\n", __func__, skb);
+
+ if (tx_info->flags & IEEE80211_TX_CTL_NO_ACK ||
+ tx_info->flags & IEEE80211_TX_STAT_TX_FILTERED) {
+ /* free driver's private data area of tx_info */
+ if (tx_info->driver_data[0] != NULL)
+ kfree(tx_info->driver_data[0]);
+ tx_info->driver_data[0] = NULL;
+ }
+
+ if (tx_status->flags & ATH_TX_BAR) {
+ tx_info->flags |= IEEE80211_TX_STAT_AMPDU_NO_BACK;
+ tx_status->flags &= ~ATH_TX_BAR;
+ }
+
+ if (tx_status->flags & (ATH_TX_ERROR | ATH_TX_XRETRY)) {
+ if (!(tx_info->flags & IEEE80211_TX_CTL_NO_ACK)) {
+ /* Frame was not ACKed, but an ACK was expected */
+ tx_info->status.excessive_retries = 1;
+ }
+ } else {
+ /* Frame was ACKed */
+ tx_info->flags |= IEEE80211_TX_STAT_ACK;
+ }
+
+ tx_info->status.retry_count = tx_status->retries;
+
+ ieee80211_tx_status(hw, skb);
+ if (an)
+ ath_node_put(sc, an, ATH9K_BH_STATUS_CHANGE);
+}
+
+int _ath_rx_indicate(struct ath_softc *sc,
+ struct sk_buff *skb,
+ struct ath_recv_status *status,
+ u16 keyix)
+{
+ struct ieee80211_hw *hw = sc->hw;
+ struct ath_node *an = NULL;
+ struct ieee80211_rx_status rx_status;
+ struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
+ int hdrlen = ieee80211_get_hdrlen_from_skb(skb);
+ int padsize;
+ enum ATH_RX_TYPE st;
+
+ /* see if any padding is done by the hw and remove it */
+ if (hdrlen & 3) {
+ padsize = hdrlen % 4;
+ memmove(skb->data + padsize, skb->data, hdrlen);
+ skb_pull(skb, padsize);
+ }
+
+ /* Prepare rx status */
+ ath9k_rx_prepare(sc, skb, status, &rx_status);
+
+ if (!(keyix == ATH9K_RXKEYIX_INVALID) &&
+ !(status->flags & ATH_RX_DECRYPT_ERROR)) {
+ rx_status.flag |= RX_FLAG_DECRYPTED;
+ } else if ((le16_to_cpu(hdr->frame_control) & IEEE80211_FCTL_PROTECTED)
+ && !(status->flags & ATH_RX_DECRYPT_ERROR)
+ && skb->len >= hdrlen + 4) {
+ keyix = skb->data[hdrlen + 3] >> 6;
+
+ if (test_bit(keyix, sc->sc_keymap))
+ rx_status.flag |= RX_FLAG_DECRYPTED;
+ }
+
+ spin_lock_bh(&sc->node_lock);
+ an = ath_node_find(sc, hdr->addr2);
+ spin_unlock_bh(&sc->node_lock);
+
+ if (an) {
+ ath_rx_input(sc, an,
+ hw->conf.ht_conf.ht_supported,
+ skb, status, &st);
+ }
+ if (!an || (st != ATH_RX_CONSUMED))
+ __ieee80211_rx(hw, skb, &rx_status);
+
+ return 0;
+}
+
+int ath_rx_subframe(struct ath_node *an,
+ struct sk_buff *skb,
+ struct ath_recv_status *status)
+{
+ struct ath_softc *sc = an->an_sc;
+ struct ieee80211_hw *hw = sc->hw;
+ struct ieee80211_rx_status rx_status;
+
+ /* Prepare rx status */
+ ath9k_rx_prepare(sc, skb, status, &rx_status);
+ if (!(status->flags & ATH_RX_DECRYPT_ERROR))
+ rx_status.flag |= RX_FLAG_DECRYPTED;
+
+ __ieee80211_rx(hw, skb, &rx_status);
+
+ return 0;
+}
+
+/********************************/
+/* LED functions */
+/********************************/
+
+static void ath_led_brightness(struct led_classdev *led_cdev,
+ enum led_brightness brightness)
+{
+ struct ath_led *led = container_of(led_cdev, struct ath_led, led_cdev);
+ struct ath_softc *sc = led->sc;
+
+ switch (brightness) {
+ case LED_OFF:
+ if (led->led_type == ATH_LED_ASSOC ||
+ led->led_type == ATH_LED_RADIO)
+ sc->sc_flags &= ~SC_OP_LED_ASSOCIATED;
+ ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN,
+ (led->led_type == ATH_LED_RADIO) ? 1 :
+ !!(sc->sc_flags & SC_OP_LED_ASSOCIATED));
+ break;
+ case LED_FULL:
+ if (led->led_type == ATH_LED_ASSOC)
+ sc->sc_flags |= SC_OP_LED_ASSOCIATED;
+ ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 0);
+ break;
+ default:
+ break;
+ }
+}
+
+static int ath_register_led(struct ath_softc *sc, struct ath_led *led,
+ char *trigger)
+{
+ int ret;
+
+ led->sc = sc;
+ led->led_cdev.name = led->name;
+ led->led_cdev.default_trigger = trigger;
+ led->led_cdev.brightness_set = ath_led_brightness;
+
+ ret = led_classdev_register(wiphy_dev(sc->hw->wiphy), &led->led_cdev);
+ if (ret)
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "Failed to register led:%s", led->name);
+ else
+ led->registered = 1;
+ return ret;
+}
+
+static void ath_unregister_led(struct ath_led *led)
+{
+ if (led->registered) {
+ led_classdev_unregister(&led->led_cdev);
+ led->registered = 0;
+ }
+}
+
+static void ath_deinit_leds(struct ath_softc *sc)
+{
+ ath_unregister_led(&sc->assoc_led);
+ sc->sc_flags &= ~SC_OP_LED_ASSOCIATED;
+ ath_unregister_led(&sc->tx_led);
+ ath_unregister_led(&sc->rx_led);
+ ath_unregister_led(&sc->radio_led);
+ ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 1);
+}
+
+static void ath_init_leds(struct ath_softc *sc)
+{
+ char *trigger;
+ int ret;
+
+ /* Configure gpio 1 for output */
+ ath9k_hw_cfg_output(sc->sc_ah, ATH_LED_PIN,
+ AR_GPIO_OUTPUT_MUX_AS_OUTPUT);
+ /* LED off, active low */
+ ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 1);
+
+ trigger = ieee80211_get_radio_led_name(sc->hw);
+ snprintf(sc->radio_led.name, sizeof(sc->radio_led.name),
+ "ath9k-%s:radio", wiphy_name(sc->hw->wiphy));
+ ret = ath_register_led(sc, &sc->radio_led, trigger);
+ sc->radio_led.led_type = ATH_LED_RADIO;
+ if (ret)
+ goto fail;
+
+ trigger = ieee80211_get_assoc_led_name(sc->hw);
+ snprintf(sc->assoc_led.name, sizeof(sc->assoc_led.name),
+ "ath9k-%s:assoc", wiphy_name(sc->hw->wiphy));
+ ret = ath_register_led(sc, &sc->assoc_led, trigger);
+ sc->assoc_led.led_type = ATH_LED_ASSOC;
+ if (ret)
+ goto fail;
+
+ trigger = ieee80211_get_tx_led_name(sc->hw);
+ snprintf(sc->tx_led.name, sizeof(sc->tx_led.name),
+ "ath9k-%s:tx", wiphy_name(sc->hw->wiphy));
+ ret = ath_register_led(sc, &sc->tx_led, trigger);
+ sc->tx_led.led_type = ATH_LED_TX;
+ if (ret)
+ goto fail;
+
+ trigger = ieee80211_get_rx_led_name(sc->hw);
+ snprintf(sc->rx_led.name, sizeof(sc->rx_led.name),
+ "ath9k-%s:rx", wiphy_name(sc->hw->wiphy));
+ ret = ath_register_led(sc, &sc->rx_led, trigger);
+ sc->rx_led.led_type = ATH_LED_RX;
+ if (ret)
+ goto fail;
+
+ return;
+
+fail:
+ ath_deinit_leds(sc);
+}
+
+static int ath_detach(struct ath_softc *sc)
+{
+ struct ieee80211_hw *hw = sc->hw;
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Detach ATH hw\n", __func__);
+
+ /* Deinit LED control */
+ ath_deinit_leds(sc);
+
+#ifdef CONFIG_RFKILL
+ /* deinit rfkill */
+ ath_deinit_rfkill(sc);
+#endif
+
+ /* Unregister hw */
+
+ ieee80211_unregister_hw(hw);
+
+ /* unregister Rate control */
+ ath_rate_control_unregister();
+
+ /* tx/rx cleanup */
+
+ ath_rx_cleanup(sc);
+ ath_tx_cleanup(sc);
+
+ /* Deinit */
+
+ ath_deinit(sc);
+
+ return 0;
+}
+
+static int ath_attach(u16 devid,
+ struct ath_softc *sc)
+{
+ struct ieee80211_hw *hw = sc->hw;
+ int error = 0;
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Attach ATH hw\n", __func__);
+
+ error = ath_init(devid, sc);
+ if (error != 0)
+ return error;
+
+ /* Init nodes */
+
+ INIT_LIST_HEAD(&sc->node_list);
+ spin_lock_init(&sc->node_lock);
+
+ /* get mac address from hardware and set in mac80211 */
+
+ SET_IEEE80211_PERM_ADDR(hw, sc->sc_myaddr);
+
+ /* setup channels and rates */
+
+ sc->sbands[IEEE80211_BAND_2GHZ].channels =
+ sc->channels[IEEE80211_BAND_2GHZ];
+ sc->sbands[IEEE80211_BAND_2GHZ].bitrates =
+ sc->rates[IEEE80211_BAND_2GHZ];
+ sc->sbands[IEEE80211_BAND_2GHZ].band = IEEE80211_BAND_2GHZ;
+
+ if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT)
+ /* Setup HT capabilities for 2.4Ghz*/
+ setup_ht_cap(&sc->sbands[IEEE80211_BAND_2GHZ].ht_info);
+
+ hw->wiphy->bands[IEEE80211_BAND_2GHZ] =
+ &sc->sbands[IEEE80211_BAND_2GHZ];
+
+ if (test_bit(ATH9K_MODE_11A, sc->sc_ah->ah_caps.wireless_modes)) {
+ sc->sbands[IEEE80211_BAND_5GHZ].channels =
+ sc->channels[IEEE80211_BAND_5GHZ];
+ sc->sbands[IEEE80211_BAND_5GHZ].bitrates =
+ sc->rates[IEEE80211_BAND_5GHZ];
+ sc->sbands[IEEE80211_BAND_5GHZ].band =
+ IEEE80211_BAND_5GHZ;
+
+ if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT)
+ /* Setup HT capabilities for 5Ghz*/
+ setup_ht_cap(&sc->sbands[IEEE80211_BAND_5GHZ].ht_info);
+
+ hw->wiphy->bands[IEEE80211_BAND_5GHZ] =
+ &sc->sbands[IEEE80211_BAND_5GHZ];
+ }
+
+ /* FIXME: Have to figure out proper hw init values later */
+
+ hw->queues = 4;
+ hw->ampdu_queues = 1;
+
+ /* Register rate control */
+ hw->rate_control_algorithm = "ath9k_rate_control";
+ error = ath_rate_control_register();
+ if (error != 0) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Unable to register rate control "
+ "algorithm:%d\n", __func__, error);
+ ath_rate_control_unregister();
+ goto bad;
+ }
+
+ error = ieee80211_register_hw(hw);
+ if (error != 0) {
+ ath_rate_control_unregister();
+ goto bad;
+ }
+
+ /* Initialize LED control */
+ ath_init_leds(sc);
+
+#ifdef CONFIG_RFKILL
+ /* Initialze h/w Rfkill */
+ if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT)
+ INIT_DELAYED_WORK(&sc->rf_kill.rfkill_poll, ath_rfkill_poll);
+
+ /* Initialize s/w rfkill */
+ if (ath_init_sw_rfkill(sc))
+ goto detach;
+#endif
+
+ /* initialize tx/rx engine */
+
+ error = ath_tx_init(sc, ATH_TXBUF);
+ if (error != 0)
+ goto detach;
+
+ error = ath_rx_init(sc, ATH_RXBUF);
+ if (error != 0)
+ goto detach;
+
+ return 0;
+detach:
+ ath_detach(sc);
+bad:
+ return error;
+}
+
static int ath9k_start(struct ieee80211_hw *hw)
{
struct ath_softc *sc = hw->priv;
@@ -354,6 +1041,34 @@ static int ath9k_start(struct ieee80211_hw *hw)
}
ieee80211_wake_queues(hw);
+
+#ifdef CONFIG_RFKILL
+ /* Start rfkill polling */
+ if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT)
+ queue_delayed_work(sc->hw->workqueue,
+ &sc->rf_kill.rfkill_poll, 0);
+
+ if (!(sc->sc_flags & SC_OP_RFKILL_REGISTERED)) {
+ if (rfkill_register(sc->rf_kill.rfkill)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "Unable to register rfkill\n");
+ rfkill_free(sc->rf_kill.rfkill);
+
+ /* Deinitialize the device */
+ if (sc->pdev->irq)
+ free_irq(sc->pdev->irq, sc);
+ ath_detach(sc);
+ pci_iounmap(sc->pdev, sc->mem);
+ pci_release_region(sc->pdev, 0);
+ pci_disable_device(sc->pdev);
+ ieee80211_free_hw(hw);
+ return -EIO;
+ } else {
+ sc->sc_flags |= SC_OP_RFKILL_REGISTERED;
+ }
+ }
+#endif
+
return 0;
}
@@ -414,6 +1129,11 @@ static void ath9k_stop(struct ieee80211_hw *hw)
"%s: Device is no longer present\n", __func__);
ieee80211_stop_queues(hw);
+
+#ifdef CONFIG_RFKILL
+ if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT)
+ cancel_delayed_work_sync(&sc->rf_kill.rfkill_poll);
+#endif
}
static int ath9k_add_interface(struct ieee80211_hw *hw,
@@ -798,117 +1518,6 @@ static int ath9k_set_key(struct ieee80211_hw *hw,
return ret;
}
-static void ath9k_ht_conf(struct ath_softc *sc,
- struct ieee80211_bss_conf *bss_conf)
-{
-#define IEEE80211_HT_CAP_40MHZ_INTOLERANT BIT(14)
- struct ath_ht_info *ht_info = &sc->sc_ht_info;
-
- if (bss_conf->assoc_ht) {
- ht_info->ext_chan_offset =
- bss_conf->ht_bss_conf->bss_cap &
- IEEE80211_HT_IE_CHA_SEC_OFFSET;
-
- if (!(bss_conf->ht_conf->cap &
- IEEE80211_HT_CAP_40MHZ_INTOLERANT) &&
- (bss_conf->ht_bss_conf->bss_cap &
- IEEE80211_HT_IE_CHA_WIDTH))
- ht_info->tx_chan_width = ATH9K_HT_MACMODE_2040;
- else
- ht_info->tx_chan_width = ATH9K_HT_MACMODE_20;
-
- ath9k_hw_set11nmac2040(sc->sc_ah, ht_info->tx_chan_width);
- ht_info->maxampdu = 1 << (IEEE80211_HTCAP_MAXRXAMPDU_FACTOR +
- bss_conf->ht_conf->ampdu_factor);
- ht_info->mpdudensity =
- parse_mpdudensity(bss_conf->ht_conf->ampdu_density);
-
- }
-
-#undef IEEE80211_HT_CAP_40MHZ_INTOLERANT
-}
-
-static void ath9k_bss_assoc_info(struct ath_softc *sc,
- struct ieee80211_bss_conf *bss_conf)
-{
- struct ieee80211_hw *hw = sc->hw;
- struct ieee80211_channel *curchan = hw->conf.channel;
- struct ath_vap *avp;
- int pos;
- DECLARE_MAC_BUF(mac);
-
- if (bss_conf->assoc) {
- DPRINTF(sc, ATH_DBG_CONFIG, "%s: Bss Info ASSOC %d\n",
- __func__,
- bss_conf->aid);
-
- avp = sc->sc_vaps[0];
- if (avp == NULL) {
- DPRINTF(sc, ATH_DBG_FATAL, "%s: Invalid interface\n",
- __func__);
- return;
- }
-
- /* New association, store aid */
- if (avp->av_opmode == ATH9K_M_STA) {
- sc->sc_curaid = bss_conf->aid;
- ath9k_hw_write_associd(sc->sc_ah, sc->sc_curbssid,
- sc->sc_curaid);
- }
-
- /* Configure the beacon */
- ath_beacon_config(sc, 0);
- sc->sc_flags |= SC_OP_BEACONS;
-
- /* Reset rssi stats */
- sc->sc_halstats.ns_avgbrssi = ATH_RSSI_DUMMY_MARKER;
- sc->sc_halstats.ns_avgrssi = ATH_RSSI_DUMMY_MARKER;
- sc->sc_halstats.ns_avgtxrssi = ATH_RSSI_DUMMY_MARKER;
- sc->sc_halstats.ns_avgtxrate = ATH_RATE_DUMMY_MARKER;
-
- /* Update chainmask */
- ath_update_chainmask(sc, bss_conf->assoc_ht);
-
- DPRINTF(sc, ATH_DBG_CONFIG,
- "%s: bssid %s aid 0x%x\n",
- __func__,
- print_mac(mac, sc->sc_curbssid), sc->sc_curaid);
-
- DPRINTF(sc, ATH_DBG_CONFIG, "%s: Set channel: %d MHz\n",
- __func__,
- curchan->center_freq);
-
- pos = ath_get_channel(sc, curchan);
- if (pos == -1) {
- DPRINTF(sc, ATH_DBG_FATAL,
- "%s: Invalid channel\n", __func__);
- return;
- }
-
- if (hw->conf.ht_conf.ht_supported)
- sc->sc_ah->ah_channels[pos].chanmode =
- ath_get_extchanmode(sc, curchan);
- else
- sc->sc_ah->ah_channels[pos].chanmode =
- (curchan->band == IEEE80211_BAND_2GHZ) ?
- CHANNEL_G : CHANNEL_A;
-
- /* set h/w channel */
- if (ath_set_channel(sc, &sc->sc_ah->ah_channels[pos]) < 0)
- DPRINTF(sc, ATH_DBG_FATAL,
- "%s: Unable to set channel\n",
- __func__);
-
- ath_rate_newstate(sc, avp);
- /* Update ratectrl about the new state */
- ath_rc_node_update(hw, avp->rc_node);
- } else {
- DPRINTF(sc, ATH_DBG_CONFIG,
- "%s: Bss Info DISSOC\n", __func__);
- sc->sc_curaid = 0;
- }
-}
-
static void ath9k_bss_info_changed(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
struct ieee80211_bss_conf *bss_conf,
@@ -1048,364 +1657,6 @@ static struct ieee80211_ops ath9k_ops = {
.ampdu_action = ath9k_ampdu_action
};
-void ath_get_beaconconfig(struct ath_softc *sc,
- int if_id,
- struct ath_beacon_config *conf)
-{
- struct ieee80211_hw *hw = sc->hw;
-
- /* fill in beacon config data */
-
- conf->beacon_interval = hw->conf.beacon_int;
- conf->listen_interval = 100;
- conf->dtim_count = 1;
- conf->bmiss_timeout = ATH_DEFAULT_BMISS_LIMIT * conf->listen_interval;
-}
-
-void ath_tx_complete(struct ath_softc *sc, struct sk_buff *skb,
- struct ath_xmit_status *tx_status, struct ath_node *an)
-{
- struct ieee80211_hw *hw = sc->hw;
- struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
-
- DPRINTF(sc, ATH_DBG_XMIT,
- "%s: TX complete: skb: %p\n", __func__, skb);
-
- if (tx_info->flags & IEEE80211_TX_CTL_NO_ACK ||
- tx_info->flags & IEEE80211_TX_STAT_TX_FILTERED) {
- /* free driver's private data area of tx_info */
- if (tx_info->driver_data[0] != NULL)
- kfree(tx_info->driver_data[0]);
- tx_info->driver_data[0] = NULL;
- }
-
- if (tx_status->flags & ATH_TX_BAR) {
- tx_info->flags |= IEEE80211_TX_STAT_AMPDU_NO_BACK;
- tx_status->flags &= ~ATH_TX_BAR;
- }
-
- if (tx_status->flags & (ATH_TX_ERROR | ATH_TX_XRETRY)) {
- if (!(tx_info->flags & IEEE80211_TX_CTL_NO_ACK)) {
- /* Frame was not ACKed, but an ACK was expected */
- tx_info->status.excessive_retries = 1;
- }
- } else {
- /* Frame was ACKed */
- tx_info->flags |= IEEE80211_TX_STAT_ACK;
- }
-
- tx_info->status.retry_count = tx_status->retries;
-
- ieee80211_tx_status(hw, skb);
- if (an)
- ath_node_put(sc, an, ATH9K_BH_STATUS_CHANGE);
-}
-
-int _ath_rx_indicate(struct ath_softc *sc,
- struct sk_buff *skb,
- struct ath_recv_status *status,
- u16 keyix)
-{
- struct ieee80211_hw *hw = sc->hw;
- struct ath_node *an = NULL;
- struct ieee80211_rx_status rx_status;
- struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
- int hdrlen = ieee80211_get_hdrlen_from_skb(skb);
- int padsize;
- enum ATH_RX_TYPE st;
-
- /* see if any padding is done by the hw and remove it */
- if (hdrlen & 3) {
- padsize = hdrlen % 4;
- memmove(skb->data + padsize, skb->data, hdrlen);
- skb_pull(skb, padsize);
- }
-
- /* Prepare rx status */
- ath9k_rx_prepare(sc, skb, status, &rx_status);
-
- if (!(keyix == ATH9K_RXKEYIX_INVALID) &&
- !(status->flags & ATH_RX_DECRYPT_ERROR)) {
- rx_status.flag |= RX_FLAG_DECRYPTED;
- } else if ((le16_to_cpu(hdr->frame_control) & IEEE80211_FCTL_PROTECTED)
- && !(status->flags & ATH_RX_DECRYPT_ERROR)
- && skb->len >= hdrlen + 4) {
- keyix = skb->data[hdrlen + 3] >> 6;
-
- if (test_bit(keyix, sc->sc_keymap))
- rx_status.flag |= RX_FLAG_DECRYPTED;
- }
-
- spin_lock_bh(&sc->node_lock);
- an = ath_node_find(sc, hdr->addr2);
- spin_unlock_bh(&sc->node_lock);
-
- if (an) {
- ath_rx_input(sc, an,
- hw->conf.ht_conf.ht_supported,
- skb, status, &st);
- }
- if (!an || (st != ATH_RX_CONSUMED))
- __ieee80211_rx(hw, skb, &rx_status);
-
- return 0;
-}
-
-int ath_rx_subframe(struct ath_node *an,
- struct sk_buff *skb,
- struct ath_recv_status *status)
-{
- struct ath_softc *sc = an->an_sc;
- struct ieee80211_hw *hw = sc->hw;
- struct ieee80211_rx_status rx_status;
-
- /* Prepare rx status */
- ath9k_rx_prepare(sc, skb, status, &rx_status);
- if (!(status->flags & ATH_RX_DECRYPT_ERROR))
- rx_status.flag |= RX_FLAG_DECRYPTED;
-
- __ieee80211_rx(hw, skb, &rx_status);
-
- return 0;
-}
-
-/********************************/
-/* LED functions */
-/********************************/
-
-static void ath_led_brightness(struct led_classdev *led_cdev,
- enum led_brightness brightness)
-{
- struct ath_led *led = container_of(led_cdev, struct ath_led, led_cdev);
- struct ath_softc *sc = led->sc;
-
- switch (brightness) {
- case LED_OFF:
- if (led->led_type == ATH_LED_ASSOC ||
- led->led_type == ATH_LED_RADIO)
- sc->sc_flags &= ~SC_OP_LED_ASSOCIATED;
- ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN,
- (led->led_type == ATH_LED_RADIO) ? 1 :
- !!(sc->sc_flags & SC_OP_LED_ASSOCIATED));
- break;
- case LED_FULL:
- if (led->led_type == ATH_LED_ASSOC)
- sc->sc_flags |= SC_OP_LED_ASSOCIATED;
- ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 0);
- break;
- default:
- break;
- }
-}
-
-static int ath_register_led(struct ath_softc *sc, struct ath_led *led,
- char *trigger)
-{
- int ret;
-
- led->sc = sc;
- led->led_cdev.name = led->name;
- led->led_cdev.default_trigger = trigger;
- led->led_cdev.brightness_set = ath_led_brightness;
-
- ret = led_classdev_register(wiphy_dev(sc->hw->wiphy), &led->led_cdev);
- if (ret)
- DPRINTF(sc, ATH_DBG_FATAL,
- "Failed to register led:%s", led->name);
- else
- led->registered = 1;
- return ret;
-}
-
-static void ath_unregister_led(struct ath_led *led)
-{
- if (led->registered) {
- led_classdev_unregister(&led->led_cdev);
- led->registered = 0;
- }
-}
-
-static void ath_deinit_leds(struct ath_softc *sc)
-{
- ath_unregister_led(&sc->assoc_led);
- sc->sc_flags &= ~SC_OP_LED_ASSOCIATED;
- ath_unregister_led(&sc->tx_led);
- ath_unregister_led(&sc->rx_led);
- ath_unregister_led(&sc->radio_led);
- ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 1);
-}
-
-static void ath_init_leds(struct ath_softc *sc)
-{
- char *trigger;
- int ret;
-
- /* Configure gpio 1 for output */
- ath9k_hw_cfg_output(sc->sc_ah, ATH_LED_PIN,
- AR_GPIO_OUTPUT_MUX_AS_OUTPUT);
- /* LED off, active low */
- ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 1);
-
- trigger = ieee80211_get_radio_led_name(sc->hw);
- snprintf(sc->radio_led.name, sizeof(sc->radio_led.name),
- "ath9k-%s:radio", wiphy_name(sc->hw->wiphy));
- ret = ath_register_led(sc, &sc->radio_led, trigger);
- sc->radio_led.led_type = ATH_LED_RADIO;
- if (ret)
- goto fail;
-
- trigger = ieee80211_get_assoc_led_name(sc->hw);
- snprintf(sc->assoc_led.name, sizeof(sc->assoc_led.name),
- "ath9k-%s:assoc", wiphy_name(sc->hw->wiphy));
- ret = ath_register_led(sc, &sc->assoc_led, trigger);
- sc->assoc_led.led_type = ATH_LED_ASSOC;
- if (ret)
- goto fail;
-
- trigger = ieee80211_get_tx_led_name(sc->hw);
- snprintf(sc->tx_led.name, sizeof(sc->tx_led.name),
- "ath9k-%s:tx", wiphy_name(sc->hw->wiphy));
- ret = ath_register_led(sc, &sc->tx_led, trigger);
- sc->tx_led.led_type = ATH_LED_TX;
- if (ret)
- goto fail;
-
- trigger = ieee80211_get_rx_led_name(sc->hw);
- snprintf(sc->rx_led.name, sizeof(sc->rx_led.name),
- "ath9k-%s:rx", wiphy_name(sc->hw->wiphy));
- ret = ath_register_led(sc, &sc->rx_led, trigger);
- sc->rx_led.led_type = ATH_LED_RX;
- if (ret)
- goto fail;
-
- return;
-
-fail:
- ath_deinit_leds(sc);
-}
-
-static int ath_detach(struct ath_softc *sc)
-{
- struct ieee80211_hw *hw = sc->hw;
-
- DPRINTF(sc, ATH_DBG_CONFIG, "%s: Detach ATH hw\n", __func__);
-
- /* Deinit LED control */
- ath_deinit_leds(sc);
-
- /* Unregister hw */
-
- ieee80211_unregister_hw(hw);
-
- /* unregister Rate control */
- ath_rate_control_unregister();
-
- /* tx/rx cleanup */
-
- ath_rx_cleanup(sc);
- ath_tx_cleanup(sc);
-
- /* Deinit */
-
- ath_deinit(sc);
-
- return 0;
-}
-
-static int ath_attach(u16 devid,
- struct ath_softc *sc)
-{
- struct ieee80211_hw *hw = sc->hw;
- int error = 0;
-
- DPRINTF(sc, ATH_DBG_CONFIG, "%s: Attach ATH hw\n", __func__);
-
- error = ath_init(devid, sc);
- if (error != 0)
- return error;
-
- /* Init nodes */
-
- INIT_LIST_HEAD(&sc->node_list);
- spin_lock_init(&sc->node_lock);
-
- /* get mac address from hardware and set in mac80211 */
-
- SET_IEEE80211_PERM_ADDR(hw, sc->sc_myaddr);
-
- /* setup channels and rates */
-
- sc->sbands[IEEE80211_BAND_2GHZ].channels =
- sc->channels[IEEE80211_BAND_2GHZ];
- sc->sbands[IEEE80211_BAND_2GHZ].bitrates =
- sc->rates[IEEE80211_BAND_2GHZ];
- sc->sbands[IEEE80211_BAND_2GHZ].band = IEEE80211_BAND_2GHZ;
-
- if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT)
- /* Setup HT capabilities for 2.4Ghz*/
- setup_ht_cap(&sc->sbands[IEEE80211_BAND_2GHZ].ht_info);
-
- hw->wiphy->bands[IEEE80211_BAND_2GHZ] =
- &sc->sbands[IEEE80211_BAND_2GHZ];
-
- if (test_bit(ATH9K_MODE_11A, sc->sc_ah->ah_caps.wireless_modes)) {
- sc->sbands[IEEE80211_BAND_5GHZ].channels =
- sc->channels[IEEE80211_BAND_5GHZ];
- sc->sbands[IEEE80211_BAND_5GHZ].bitrates =
- sc->rates[IEEE80211_BAND_5GHZ];
- sc->sbands[IEEE80211_BAND_5GHZ].band =
- IEEE80211_BAND_5GHZ;
-
- if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT)
- /* Setup HT capabilities for 5Ghz*/
- setup_ht_cap(&sc->sbands[IEEE80211_BAND_5GHZ].ht_info);
-
- hw->wiphy->bands[IEEE80211_BAND_5GHZ] =
- &sc->sbands[IEEE80211_BAND_5GHZ];
- }
-
- /* FIXME: Have to figure out proper hw init values later */
-
- hw->queues = 4;
- hw->ampdu_queues = 1;
-
- /* Register rate control */
- hw->rate_control_algorithm = "ath9k_rate_control";
- error = ath_rate_control_register();
- if (error != 0) {
- DPRINTF(sc, ATH_DBG_FATAL,
- "%s: Unable to register rate control "
- "algorithm:%d\n", __func__, error);
- ath_rate_control_unregister();
- goto bad;
- }
-
- error = ieee80211_register_hw(hw);
- if (error != 0) {
- ath_rate_control_unregister();
- goto bad;
- }
-
- /* Initialize LED control */
- ath_init_leds(sc);
-
- /* initialize tx/rx engine */
-
- error = ath_tx_init(sc, ATH_TXBUF);
- if (error != 0)
- goto detach;
-
- error = ath_rx_init(sc, ATH_RXBUF);
- if (error != 0)
- goto detach;
-
- return 0;
-detach:
- ath_detach(sc);
-bad:
- return error;
-}
-
static int ath_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
{
void __iomem *mem;
@@ -1554,6 +1805,12 @@ static int ath_pci_suspend(struct pci_dev *pdev, pm_message_t state)
struct ath_softc *sc = hw->priv;
ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 1);
+
+#ifdef CONFIG_RFKILL
+ if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT)
+ cancel_delayed_work_sync(&sc->rf_kill.rfkill_poll);
+#endif
+
pci_save_state(pdev);
pci_disable_device(pdev);
pci_set_power_state(pdev, 3);
@@ -1586,6 +1843,16 @@ static int ath_pci_resume(struct pci_dev *pdev)
AR_GPIO_OUTPUT_MUX_AS_OUTPUT);
ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 1);
+#ifdef CONFIG_RFKILL
+ /*
+ * check the h/w rfkill state on resume
+ * and start the rfkill poll timer
+ */
+ if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT)
+ queue_delayed_work(sc->hw->workqueue,
+ &sc->rf_kill.rfkill_poll, 0);
+#endif
+
return 0;
}
--
1.5.5.1
This is much better, the rfkill bits seem fine at first glance.
--
"One disk to rule them all, One disk to find them. One disk to bring
them all and in the darkness grind them. In the Land of Redmond
where the shadows lie." -- The Silicon Valley Tarot
Henrique Holschuh
Johannes Berg wrote:
>> +#ifdef CONFIG_RFKILL
>> + u16 ah_rfsilent;
>> + u32 ah_rfkill_gpio ;
>>
>
> small typo, space too much.
>
>
ok, thanks.
>> --- a/drivers/net/wireless/ath9k/core.h
>> +++ b/drivers/net/wireless/ath9k/core.h
>> @@ -40,6 +40,9 @@
>> #include <asm/page.h>
>> #include <net/mac80211.h>
>> #include <linux/leds.h>
>> +#ifdef CONFIG_RFKILL
>> +#include <linux/rfkill.h>
>> +#endif
>>
>> #include "ath9k.h"
>> #include "rc.h"
>> @@ -823,6 +826,17 @@ struct ath_led {
>> bool registered;
>> };
>>
>> +#ifdef CONFIG_RFKILL
>> +/* Rfkill */
>> +#define ATH_RFKILL_POLL_INTERVAL 2000 /* msecs */
>> +
>> +struct ath_rfkill {
>> + struct rfkill *rfkill;
>> + struct delayed_work rfkill_poll;
>> + char rfkill_name[32];
>> +};
>> +#endif
>> +
>>
>
> No need to protect any of this with an #ifdef.
>
>
>> +#ifdef CONFIG_RFKILL
>> +#define SC_OP_RFKILL_REGISTERED BIT(11)
>> +#define SC_OP_RFKILL_SW_BLOCKED BIT(12)
>> +#define SC_OP_RFKILL_HW_BLOCKED BIT(13)
>> +#endif
>>
>
> Nor that.
>
>
ok.
>> +static void ath9k_ht_conf(struct ath_softc *sc,
>> + struct ieee80211_bss_conf *bss_conf)
>> +{
>> +#define IEEE80211_HT_CAP_40MHZ_INTOLERANT BIT(14)
>> + struct ath_ht_info *ht_info = &sc->sc_ht_info;
>>
>
> All that doesn't seem to belong into this patch?
>
> johannes
>
I just rearranged (purely change in the location of few static functions
in the file) the code to avoid
the prototype declaration of the functions which are called (before
their definition) in case of any
failure during rfkill_register().
Thanks for your comments.
Regards
Vasanth
Henrique de Moraes Holschuh wrote:
> On Tue, 09 Sep 2008, vasanthakumar thiagarajan wrote:
>
>> I just rearranged (purely change in the location of few static functions
>> in the file) the code to avoid
>> the prototype declaration of the functions which are called (before
>> their definition) in case of any
>> failure during rfkill_register().
>>
>
> That's much better done in two patches.
>
> The first patch should just move code around without changing *anything*.
> You can check the resulting binary to be sure you didn't change any code by
> mistake.
>
> The second patch does the real code changes.
>
> --
> "One disk to rule them all, One disk to find them. One disk to bring
> them all and in the darkness grind them. In the Land of Redmond
> where the shadows lie." -- The Silicon Valley Tarot
> Henrique Holschuh
>
Yeah, I got it. Thanks.
Vasanth
Johannes Berg wrote:
> On Tue, 2008-09-09 at 21:04 +0530, Vasanthakumar Thiagarajan wrote:
>
>> This support is compiled in if CONFIG_RFKILL
>> option is set.
>>
>
>
>> +++ b/drivers/net/wireless/ath9k/Kconfig
>> @@ -4,6 +4,7 @@ config ATH9K
>> select MAC80211_LEDS
>> select LEDS_CLASS
>> select NEW_LEDS
>> + select RFKILL
>>
>
> You really want to drop that then though.
>
> johannes
>
Yeah, I missed this one. Thanks.
Vasanth
On Tue, 09 Sep 2008, vasanthakumar thiagarajan wrote:
> I just rearranged (purely change in the location of few static functions
> in the file) the code to avoid
> the prototype declaration of the functions which are called (before
> their definition) in case of any
> failure during rfkill_register().
That's much better done in two patches.
The first patch should just move code around without changing *anything*.
You can check the resulting binary to be sure you didn't change any code by
mistake.
The second patch does the real code changes.
--
"One disk to rule them all, One disk to find them. One disk to bring
them all and in the darkness grind them. In the Land of Redmond
where the shadows lie." -- The Silicon Valley Tarot
Henrique Holschuh
> +#ifdef CONFIG_RFKILL
> + u16 ah_rfsilent;
> + u32 ah_rfkill_gpio ;
small typo, space too much.
> --- a/drivers/net/wireless/ath9k/core.h
> +++ b/drivers/net/wireless/ath9k/core.h
> @@ -40,6 +40,9 @@
> #include <asm/page.h>
> #include <net/mac80211.h>
> #include <linux/leds.h>
> +#ifdef CONFIG_RFKILL
> +#include <linux/rfkill.h>
> +#endif
>
> #include "ath9k.h"
> #include "rc.h"
> @@ -823,6 +826,17 @@ struct ath_led {
> bool registered;
> };
>
> +#ifdef CONFIG_RFKILL
> +/* Rfkill */
> +#define ATH_RFKILL_POLL_INTERVAL 2000 /* msecs */
> +
> +struct ath_rfkill {
> + struct rfkill *rfkill;
> + struct delayed_work rfkill_poll;
> + char rfkill_name[32];
> +};
> +#endif
> +
No need to protect any of this with an #ifdef.
> +#ifdef CONFIG_RFKILL
> +#define SC_OP_RFKILL_REGISTERED BIT(11)
> +#define SC_OP_RFKILL_SW_BLOCKED BIT(12)
> +#define SC_OP_RFKILL_HW_BLOCKED BIT(13)
> +#endif
Nor that.
> +static void ath9k_ht_conf(struct ath_softc *sc,
> + struct ieee80211_bss_conf *bss_conf)
> +{
> +#define IEEE80211_HT_CAP_40MHZ_INTOLERANT BIT(14)
> + struct ath_ht_info *ht_info = &sc->sc_ht_info;
All that doesn't seem to belong into this patch?
johannes
On Tue, 2008-09-09 at 21:04 +0530, Vasanthakumar Thiagarajan wrote:
> This support is compiled in if CONFIG_RFKILL
> option is set.
> +++ b/drivers/net/wireless/ath9k/Kconfig
> @@ -4,6 +4,7 @@ config ATH9K
> select MAC80211_LEDS
> select LEDS_CLASS
> select NEW_LEDS
> + select RFKILL
You really want to drop that then though.
johannes