The F81532/534 had 4 clocksource 1.846/18.46/14.77/24MHz and baud rates
can be up to 1.5Mbits with 24MHz.
This device may generate data overrun when baud rate setting to 921600bps
or higher with old UART trigger level setting (8x14=112) with full
loading. We'll change trigger level from 8x14=112 to 8x8=64 to avoid data
overrun.
Also the read/write of EP0 will be affected by this patch. The worst case
of responding time is 20s when all serial port are full loading and trying
to access EP0, so we change EP0 timeout from 10 to 20s.
F81532/534 Clock register (offset +08h)
Bit0: UART Enable (always on)
Bit2-1: Clock source selector
00: 1.846MHz.
01: 18.46MHz.
10: 24MHz.
11: 14.77MHz.
Signed-off-by: Ji-Ze Hong (Peter Hong) <[email protected]>
---
V3:
1: Separate UART Enable bit from clock sources and active it in
port_probe() with port_priv->shadow_clk.
2: Add sanity check for clocksource idx in set_port_config().
3: change calc_baud_divisor() parameter from F81534_MAX_BAUDRATE
to priv->baud_base.
v2:
1: Add commit message for F81534_USB_TIMEOUT from 1000 to 2000 and
trigger level from UART_FCR_R_TRIG_11 to UART_FCR_TRIGGER_8.
2: Separate UART Enable bit from clock sources.
3: Add help function "f81534_find_clk()" to calculate baud rate and
clock source
4: Add shadow clock register for future use.
drivers/usb/serial/f81534.c | 93 +++++++++++++++++++++++++++++++++++++--------
1 file changed, 77 insertions(+), 16 deletions(-)
diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c
index e4573b4c8935..1563d3f34381 100644
--- a/drivers/usb/serial/f81534.c
+++ b/drivers/usb/serial/f81534.c
@@ -41,6 +41,7 @@
#define F81534_MODEM_CONTROL_REG (0x04 + F81534_UART_BASE_ADDRESS)
#define F81534_LINE_STATUS_REG (0x05 + F81534_UART_BASE_ADDRESS)
#define F81534_MODEM_STATUS_REG (0x06 + F81534_UART_BASE_ADDRESS)
+#define F81534_CLOCK_REG (0x08 + F81534_UART_BASE_ADDRESS)
#define F81534_CONFIG1_REG (0x09 + F81534_UART_BASE_ADDRESS)
#define F81534_DEF_CONF_ADDRESS_START 0x3000
@@ -57,7 +58,7 @@
/* Default URB timeout for USB operations */
#define F81534_USB_MAX_RETRY 10
-#define F81534_USB_TIMEOUT 1000
+#define F81534_USB_TIMEOUT 2000
#define F81534_SET_GET_REGISTER 0xA0
#define F81534_NUM_PORT 4
@@ -96,7 +97,6 @@
#define F81534_CMD_READ 0x03
#define F81534_DEFAULT_BAUD_RATE 9600
-#define F81534_MAX_BAUDRATE 115200
#define F81534_PORT_CONF_DISABLE_PORT BIT(3)
#define F81534_PORT_CONF_NOT_EXIST_PORT BIT(7)
@@ -106,6 +106,24 @@
#define F81534_1X_RXTRIGGER 0xc3
#define F81534_8X_RXTRIGGER 0xcf
+/*
+ * F81532/534 Clock registers (offset +08h)
+ *
+ * Bit0: UART Enable (always on)
+ * Bit2-1: Clock source selector
+ * 00: 1.846MHz.
+ * 01: 18.46MHz.
+ * 10: 24MHz.
+ * 11: 14.77MHz.
+ */
+
+#define F81534_UART_EN BIT(0)
+#define F81534_CLK_1_846_MHZ 0
+#define F81534_CLK_18_46_MHZ BIT(1)
+#define F81534_CLK_24_MHZ BIT(2)
+#define F81534_CLK_14_77_MHZ GENMASK(2, 1)
+#define F81534_CLK_MASK GENMASK(2, 1)
+
static const struct usb_device_id f81534_id_table[] = {
{ USB_DEVICE(FINTEK_VENDOR_ID_1, FINTEK_DEVICE_ID) },
{ USB_DEVICE(FINTEK_VENDOR_ID_2, FINTEK_DEVICE_ID) },
@@ -129,12 +147,18 @@ struct f81534_port_private {
struct usb_serial_port *port;
unsigned long tx_empty;
spinlock_t msr_lock;
+ u32 baud_base;
u8 shadow_mcr;
u8 shadow_lcr;
u8 shadow_msr;
+ u8 shadow_clk;
u8 phy_num;
};
+static u32 const baudrate_table[] = { 115200, 921600, 1152000, 1500000 };
+static u8 const clock_table[] = { F81534_CLK_1_846_MHZ, F81534_CLK_14_77_MHZ,
+ F81534_CLK_18_46_MHZ, F81534_CLK_24_MHZ };
+
static int f81534_logic_to_phy_port(struct usb_serial *serial,
struct usb_serial_port *port)
{
@@ -460,13 +484,52 @@ static u32 f81534_calc_baud_divisor(u32 baudrate, u32 clockrate)
return DIV_ROUND_CLOSEST(clockrate, baudrate);
}
-static int f81534_set_port_config(struct usb_serial_port *port, u32 baudrate,
- u8 lcr)
+static int f81534_find_clk(u32 baudrate)
+{
+ int idx;
+
+ for (idx = 0; idx < ARRAY_SIZE(baudrate_table); ++idx) {
+ if (baudrate <= baudrate_table[idx] &&
+ baudrate_table[idx] % baudrate == 0)
+ return idx;
+ }
+
+ return -EINVAL;
+}
+
+static int f81534_set_port_config(struct usb_serial_port *port,
+ struct tty_struct *tty, u32 baudrate, u32 old_baudrate, u8 lcr)
{
struct f81534_port_private *port_priv = usb_get_serial_port_data(port);
u32 divisor;
int status;
+ int i;
+ int idx;
u8 value;
+ u32 baud_list[] = {baudrate, old_baudrate, F81534_DEFAULT_BAUD_RATE};
+
+ for (i = 0; i < ARRAY_SIZE(baud_list); ++i) {
+ idx = f81534_find_clk(baud_list[i]);
+ if (idx >= 0) {
+ baudrate = baud_list[i];
+ tty_encode_baud_rate(tty, baudrate, baudrate);
+ break;
+ }
+ }
+
+ if (idx < 0)
+ return -EINVAL;
+
+ port_priv->baud_base = baudrate_table[idx];
+ port_priv->shadow_clk &= ~F81534_CLK_MASK;
+ port_priv->shadow_clk |= clock_table[idx];
+
+ status = f81534_set_port_register(port, F81534_CLOCK_REG,
+ port_priv->shadow_clk);
+ if (status) {
+ dev_err(&port->dev, "CLOCK_REG setting failed\n");
+ return status;
+ }
if (baudrate <= 1200)
value = F81534_1X_RXTRIGGER; /* 128 FIFO & TL: 1x */
@@ -482,7 +545,7 @@ static int f81534_set_port_config(struct usb_serial_port *port, u32 baudrate,
if (baudrate <= 1200)
value = UART_FCR_TRIGGER_1 | UART_FCR_ENABLE_FIFO; /* TL: 1 */
else
- value = UART_FCR_R_TRIG_11 | UART_FCR_ENABLE_FIFO; /* TL: 14 */
+ value = UART_FCR_TRIGGER_8 | UART_FCR_ENABLE_FIFO; /* TL: 8 */
status = f81534_set_port_register(port, F81534_FIFO_CONTROL_REG,
value);
@@ -491,7 +554,7 @@ static int f81534_set_port_config(struct usb_serial_port *port, u32 baudrate,
return status;
}
- divisor = f81534_calc_baud_divisor(baudrate, F81534_MAX_BAUDRATE);
+ divisor = f81534_calc_baud_divisor(baudrate, port_priv->baud_base);
mutex_lock(&port_priv->lcr_mutex);
@@ -741,6 +804,7 @@ static void f81534_set_termios(struct tty_struct *tty,
u8 new_lcr = 0;
int status;
u32 baud;
+ u32 old_baud;
if (C_BAUD(tty) == B0)
f81534_update_mctrl(port, 0, TIOCM_DTR | TIOCM_RTS);
@@ -780,18 +844,14 @@ static void f81534_set_termios(struct tty_struct *tty,
if (!baud)
return;
- if (baud > F81534_MAX_BAUDRATE) {
- if (old_termios)
- baud = tty_termios_baud_rate(old_termios);
- else
- baud = F81534_DEFAULT_BAUD_RATE;
-
- tty_encode_baud_rate(tty, baud, baud);
- }
+ if (old_termios)
+ old_baud = tty_termios_baud_rate(old_termios);
+ else
+ old_baud = F81534_DEFAULT_BAUD_RATE;
dev_dbg(&port->dev, "%s: baud: %d\n", __func__, baud);
- status = f81534_set_port_config(port, baud, new_lcr);
+ status = f81534_set_port_config(port, tty, baud, old_baud, new_lcr);
if (status < 0) {
dev_err(&port->dev, "%s: set port config failed: %d\n",
__func__, status);
@@ -947,7 +1007,7 @@ static int f81534_get_serial_info(struct usb_serial_port *port,
tmp.type = PORT_16550A;
tmp.port = port->port_number;
tmp.line = port->minor;
- tmp.baud_base = F81534_MAX_BAUDRATE;
+ tmp.baud_base = port_priv->baud_base;
if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
return -EFAULT;
@@ -1221,6 +1281,7 @@ static int f81534_port_probe(struct usb_serial_port *port)
if (!port_priv)
return -ENOMEM;
+ port_priv->shadow_clk = F81534_UART_EN;
spin_lock_init(&port_priv->msr_lock);
mutex_init(&port_priv->mcr_mutex);
mutex_init(&port_priv->lcr_mutex);
--
2.7.4
In the original code, We'll read configuration in calc_num_ports()
and read again in attach(). In fact, we can move all content from
attach() to calc_num_ports() to simplify the code.
Signed-off-by: Ji-Ze Hong (Peter Hong) <[email protected]>
---
V3:
1: First introduced in this series patches.
drivers/usb/serial/f81534.c | 116 ++++++++++++--------------------------------
1 file changed, 31 insertions(+), 85 deletions(-)
diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c
index e7dd01310f20..bc0a4bd5dcec 100644
--- a/drivers/usb/serial/f81534.c
+++ b/drivers/usb/serial/f81534.c
@@ -753,14 +753,14 @@ static int f81534_find_config_idx(struct usb_serial *serial, u8 *index)
static int f81534_calc_num_ports(struct usb_serial *serial,
struct usb_serial_endpoints *epds)
{
+ struct f81534_serial_private *serial_priv;
struct device *dev = &serial->interface->dev;
int size_bulk_in = usb_endpoint_maxp(epds->bulk_in[0]);
int size_bulk_out = usb_endpoint_maxp(epds->bulk_out[0]);
- u8 setting[F81534_CUSTOM_DATA_SIZE];
- u8 setting_idx;
u8 num_port = 0;
+ int index = 0;
int status;
- size_t i;
+ int i;
if (size_bulk_out != F81534_WRITE_BUFFER_SIZE ||
size_bulk_in != F81534_MAX_RECEIVE_BLOCK_SIZE) {
@@ -768,8 +768,16 @@ static int f81534_calc_num_ports(struct usb_serial *serial,
return -ENODEV;
}
+ serial_priv = devm_kzalloc(&serial->interface->dev,
+ sizeof(*serial_priv), GFP_KERNEL);
+ if (!serial_priv)
+ return -ENOMEM;
+
+ usb_set_serial_data(serial, serial_priv);
+ mutex_init(&serial_priv->urb_mutex);
+
/* Check had custom setting */
- status = f81534_find_config_idx(serial, &setting_idx);
+ status = f81534_find_config_idx(serial, &serial_priv->setting_idx);
if (status) {
dev_err(&serial->interface->dev, "%s: find idx failed: %d\n",
__func__, status);
@@ -780,11 +788,12 @@ static int f81534_calc_num_ports(struct usb_serial *serial,
* We'll read custom data only when data available, otherwise we'll
* read default value instead.
*/
- if (setting_idx != F81534_CUSTOM_NO_CUSTOM_DATA) {
+ if (serial_priv->setting_idx != F81534_CUSTOM_NO_CUSTOM_DATA) {
status = f81534_read_flash(serial,
F81534_CUSTOM_ADDRESS_START +
F81534_CONF_OFFSET,
- sizeof(setting), setting);
+ sizeof(serial_priv->conf_data),
+ serial_priv->conf_data);
if (status) {
dev_err(&serial->interface->dev,
"%s: get custom data failed: %d\n",
@@ -794,13 +803,13 @@ static int f81534_calc_num_ports(struct usb_serial *serial,
dev_dbg(&serial->interface->dev,
"%s: read config from block: %d\n", __func__,
- setting_idx);
+ serial_priv->setting_idx);
} else {
/* Read default board setting */
status = f81534_read_flash(serial,
- F81534_DEF_CONF_ADDRESS_START, F81534_NUM_PORT,
- setting);
-
+ F81534_DEF_CONF_ADDRESS_START,
+ sizeof(serial_priv->conf_data),
+ serial_priv->conf_data);
if (status) {
dev_err(&serial->interface->dev,
"%s: read failed: %d\n", __func__,
@@ -814,7 +823,7 @@ static int f81534_calc_num_ports(struct usb_serial *serial,
/* New style, find all possible ports */
for (i = 0; i < F81534_NUM_PORT; ++i) {
- if (setting[i] & F81534_PORT_UNAVAILABLE)
+ if (serial_priv->conf_data[i] & F81534_PORT_UNAVAILABLE)
continue;
++num_port;
@@ -826,6 +835,17 @@ static int f81534_calc_num_ports(struct usb_serial *serial,
num_port = 4; /* Nothing found, oldest version IC */
}
+ /* Assign phy-to-logic mapping */
+ for (i = 0; i < F81534_NUM_PORT; ++i) {
+ if (serial_priv->conf_data[i] & F81534_PORT_UNAVAILABLE)
+ continue;
+
+ serial_priv->tty_idx[i] = index++;
+ dev_dbg(&serial->interface->dev,
+ "%s: phy_num: %d, tty_idx: %d\n", __func__, i,
+ serial_priv->tty_idx[i]);
+ }
+
/*
* Setup bulk-out endpoint multiplexing. All ports share the same
* bulk-out endpoint.
@@ -1227,79 +1247,6 @@ static void f81534_write_usb_callback(struct urb *urb)
}
}
-static int f81534_attach(struct usb_serial *serial)
-{
- struct f81534_serial_private *serial_priv;
- int index = 0;
- int status;
- int i;
-
- serial_priv = devm_kzalloc(&serial->interface->dev,
- sizeof(*serial_priv), GFP_KERNEL);
- if (!serial_priv)
- return -ENOMEM;
-
- usb_set_serial_data(serial, serial_priv);
-
- mutex_init(&serial_priv->urb_mutex);
-
- /* Check had custom setting */
- status = f81534_find_config_idx(serial, &serial_priv->setting_idx);
- if (status) {
- dev_err(&serial->interface->dev, "%s: find idx failed: %d\n",
- __func__, status);
- return status;
- }
-
- /*
- * We'll read custom data only when data available, otherwise we'll
- * read default value instead.
- */
- if (serial_priv->setting_idx == F81534_CUSTOM_NO_CUSTOM_DATA) {
- /*
- * The default configuration layout:
- * byte 0/1/2/3: uart setting
- */
- status = f81534_read_flash(serial,
- F81534_DEF_CONF_ADDRESS_START,
- F81534_DEF_CONF_SIZE,
- serial_priv->conf_data);
- if (status) {
- dev_err(&serial->interface->dev,
- "%s: read reserve data failed: %d\n",
- __func__, status);
- return status;
- }
- } else {
- /* Only read 8 bytes for mode & GPIO */
- status = f81534_read_flash(serial,
- F81534_CUSTOM_ADDRESS_START +
- F81534_CONF_OFFSET,
- sizeof(serial_priv->conf_data),
- serial_priv->conf_data);
- if (status) {
- dev_err(&serial->interface->dev,
- "%s: idx: %d get data failed: %d\n",
- __func__, serial_priv->setting_idx,
- status);
- return status;
- }
- }
-
- /* Assign phy-to-logic mapping */
- for (i = 0; i < F81534_NUM_PORT; ++i) {
- if (serial_priv->conf_data[i] & F81534_PORT_UNAVAILABLE)
- continue;
-
- serial_priv->tty_idx[i] = index++;
- dev_dbg(&serial->interface->dev,
- "%s: phy_num: %d, tty_idx: %d\n", __func__, i,
- serial_priv->tty_idx[i]);
- }
-
- return 0;
-}
-
static void f81534_lsr_worker(struct work_struct *work)
{
struct f81534_port_private *port_priv;
@@ -1543,7 +1490,6 @@ static struct usb_serial_driver f81534_device = {
.write = f81534_write,
.tx_empty = f81534_tx_empty,
.calc_num_ports = f81534_calc_num_ports,
- .attach = f81534_attach,
.port_probe = f81534_port_probe,
.port_remove = f81534_port_remove,
.break_ctl = f81534_break_ctl,
--
2.7.4
The F81532/534 had 4 clocksource 1.846/18.46/14.77/24MHz and baud rates
can be up to 1.5Mbits with 24MHz. But on some baud rate (384~500kps), the
TX side will send the data frame too close to treat frame error on RX
side. This patch will force all TX data frame with delay 1bit gap.
Signed-off-by: Ji-Ze Hong (Peter Hong) <[email protected]>
---
V3:
1: had not noticeable changes.
V2:
1: First introduced in this series patches.
drivers/usb/serial/f81534.c | 8 +++++++-
1 file changed, 7 insertions(+), 1 deletion(-)
diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c
index 08ef72ea2eec..92c9d8f18a5a 100644
--- a/drivers/usb/serial/f81534.c
+++ b/drivers/usb/serial/f81534.c
@@ -131,6 +131,8 @@
#define F81534_CLK_24_MHZ BIT(2)
#define F81534_CLK_14_77_MHZ GENMASK(2, 1)
#define F81534_CLK_MASK GENMASK(2, 1)
+#define F81534_CLK_TX_DELAY_1BIT BIT(3)
+
#define F81534_CLK_RS485_MODE BIT(4)
#define F81534_CLK_RS485_INVERT BIT(5)
@@ -1386,7 +1388,11 @@ static int f81534_port_probe(struct usb_serial_port *port)
if (!port_priv)
return -ENOMEM;
- port_priv->shadow_clk = F81534_UART_EN;
+ /*
+ * We'll make tx frame error when baud rate from 384~500kps. So we'll
+ * delay all tx data frame with 1bit.
+ */
+ port_priv->shadow_clk = F81534_UART_EN | F81534_CLK_TX_DELAY_1BIT;
spin_lock_init(&port_priv->msr_lock);
mutex_init(&port_priv->mcr_mutex);
mutex_init(&port_priv->lcr_mutex);
--
2.7.4
The F81532/534 can be disable port by manufacturer with
following H/W design.
1: Connect DCD/DSR/CTS/RI pin to ground.
2: Connect RX pin to ground.
In driver, we'll implements some detect method likes following:
1: Read MSR.
2: Turn MCR LOOP bit on, off and read LSR after delay with 60ms.
It'll contain BREAK status in LSR.
Signed-off-by: Ji-Ze Hong (Peter Hong) <[email protected]>
---
V3:
1: Separate old patch into refacting and H/W disable patches.
V2:
1: f81534_check_port_hw_disabled() change return type from int to bool.
2: Add help function f81534_set_phy_port_register() /
f81534_get_phy_port_register() for f81534_check_port_hw_disabled()
to read register without port.
3: Re-write f81534_calc_num_ports() & f81534_attach() to reduce the
f81534_check_port_hw_disabled() repeatedly called.
drivers/usb/serial/f81534.c | 81 +++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 81 insertions(+)
diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c
index bc0a4bd5dcec..08ef72ea2eec 100644
--- a/drivers/usb/serial/f81534.c
+++ b/drivers/usb/serial/f81534.c
@@ -307,6 +307,20 @@ static int f81534_set_mask_register(struct usb_serial *serial, u16 reg,
return f81534_set_register(serial, reg, tmp);
}
+static int f81534_set_phy_port_register(struct usb_serial *serial, int phy,
+ u16 reg, u8 data)
+{
+ return f81534_set_register(serial, reg + F81534_UART_OFFSET * phy,
+ data);
+}
+
+static int f81534_get_phy_port_register(struct usb_serial *serial, int phy,
+ u16 reg, u8 *data)
+{
+ return f81534_get_register(serial, reg + F81534_UART_OFFSET * phy,
+ data);
+}
+
static int f81534_set_port_register(struct usb_serial_port *port, u16 reg,
u8 data)
{
@@ -733,6 +747,70 @@ static int f81534_find_config_idx(struct usb_serial *serial, u8 *index)
}
/*
+ * The F81532/534 will not report serial port to USB serial subsystem when
+ * H/W DCD/DSR/CTS/RI/RX pin connected to ground.
+ *
+ * To detect RX pin status, we'll enable MCR interal loopback, disable it and
+ * delayed for 60ms. It connected to ground If LSR register report UART_LSR_BI.
+ */
+static bool f81534_check_port_hw_disabled(struct usb_serial *serial, int phy)
+{
+ int status;
+ u8 old_mcr;
+ u8 msr;
+ u8 lsr;
+ u8 msr_mask;
+
+ msr_mask = UART_MSR_DCD | UART_MSR_RI | UART_MSR_DSR | UART_MSR_CTS;
+
+ status = f81534_get_phy_port_register(serial, phy,
+ F81534_MODEM_STATUS_REG, &msr);
+ if (status)
+ return false;
+
+ if ((msr & msr_mask) != msr_mask)
+ return false;
+
+ status = f81534_set_phy_port_register(serial, phy,
+ F81534_FIFO_CONTROL_REG, UART_FCR_ENABLE_FIFO |
+ UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
+ if (status)
+ return false;
+
+ status = f81534_get_phy_port_register(serial, phy,
+ F81534_MODEM_CONTROL_REG, &old_mcr);
+ if (status)
+ return false;
+
+ status = f81534_set_phy_port_register(serial, phy,
+ F81534_MODEM_CONTROL_REG, UART_MCR_LOOP);
+ if (status)
+ return false;
+
+ status = f81534_set_phy_port_register(serial, phy,
+ F81534_MODEM_CONTROL_REG, 0x0);
+ if (status)
+ return false;
+
+ msleep(60);
+
+ status = f81534_get_phy_port_register(serial, phy,
+ F81534_LINE_STATUS_REG, &lsr);
+ if (status)
+ return false;
+
+ status = f81534_set_phy_port_register(serial, phy,
+ F81534_MODEM_CONTROL_REG, old_mcr);
+ if (status)
+ return false;
+
+ if ((lsr & UART_LSR_BI) == UART_LSR_BI)
+ return true;
+
+ return false;
+}
+
+/*
* We had 2 generation of F81532/534 IC. All has an internal storage.
*
* 1st is pure USB-to-TTL RS232 IC and designed for 4 ports only, no any
@@ -823,6 +901,9 @@ static int f81534_calc_num_ports(struct usb_serial *serial,
/* New style, find all possible ports */
for (i = 0; i < F81534_NUM_PORT; ++i) {
+ if (f81534_check_port_hw_disabled(serial, i))
+ serial_priv->conf_data[i] |= F81534_PORT_UNAVAILABLE;
+
if (serial_priv->conf_data[i] & F81534_PORT_UNAVAILABLE)
continue;
--
2.7.4
The F81532/534 had 3 output pin (M0/SD, M1, M2) with open-drain mode to
control transceiver. We'll read it from internal Flash with address
0x2f05~0x2f08 for 4 ports. The value is range from 0 to 7. The M0/SD is
MSB of this value. For a examples, If read value is 6, we'll write M0/SD,
M1, M2 as 1, 1, 0.
Signed-off-by: Ji-Ze Hong (Peter Hong) <[email protected]>
---
V3:
1: change reg_mask type from u16 to u8.
2: change space around "{" & "}".
V2:
1: Fix for space between brace.
2: Remain the old pin control method.
drivers/usb/serial/f81534.c | 67 ++++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 66 insertions(+), 1 deletion(-)
diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c
index 2201be577dd3..e7dd01310f20 100644
--- a/drivers/usb/serial/f81534.c
+++ b/drivers/usb/serial/f81534.c
@@ -52,6 +52,7 @@
#define F81534_CUSTOM_NO_CUSTOM_DATA 0xff
#define F81534_CUSTOM_VALID_TOKEN 0xf0
#define F81534_CONF_OFFSET 1
+#define F81534_CONF_GPIO_OFFSET 4
#define F81534_MAX_DATA_BLOCK 64
#define F81534_MAX_BUS_RETRY 20
@@ -164,6 +165,23 @@ struct f81534_port_private {
u8 phy_num;
};
+struct f81534_pin_data {
+ const u16 reg_addr;
+ const u8 reg_mask;
+};
+
+struct f81534_port_out_pin {
+ struct f81534_pin_data pin[3];
+};
+
+/* Pin output value for M2/M1/M0(SD) */
+static const struct f81534_port_out_pin f81534_port_out_pins[] = {
+ { { { 0x2ae8, BIT(7) }, { 0x2a90, BIT(5) }, { 0x2a90, BIT(4) } } },
+ { { { 0x2ae8, BIT(6) }, { 0x2ae8, BIT(0) }, { 0x2ae8, BIT(3) } } },
+ { { { 0x2a90, BIT(0) }, { 0x2ae8, BIT(2) }, { 0x2a80, BIT(6) } } },
+ { { { 0x2a90, BIT(3) }, { 0x2a90, BIT(2) }, { 0x2a90, BIT(1) } } },
+};
+
static u32 const baudrate_table[] = { 115200, 921600, 1152000, 1500000 };
static u8 const clock_table[] = { F81534_CLK_1_846_MHZ, F81534_CLK_14_77_MHZ,
F81534_CLK_18_46_MHZ, F81534_CLK_24_MHZ };
@@ -273,6 +291,22 @@ static int f81534_get_register(struct usb_serial *serial, u16 reg, u8 *data)
return status;
}
+static int f81534_set_mask_register(struct usb_serial *serial, u16 reg,
+ u8 mask, u8 data)
+{
+ int status;
+ u8 tmp;
+
+ status = f81534_get_register(serial, reg, &tmp);
+ if (status)
+ return status;
+
+ tmp &= ~mask;
+ tmp |= (mask & data);
+
+ return f81534_set_register(serial, reg, tmp);
+}
+
static int f81534_set_port_register(struct usb_serial_port *port, u16 reg,
u8 data)
{
@@ -1281,6 +1315,37 @@ static void f81534_lsr_worker(struct work_struct *work)
dev_warn(&port->dev, "read LSR failed: %d\n", status);
}
+static int f81534_set_port_output_pin(struct usb_serial_port *port)
+{
+ struct f81534_serial_private *serial_priv;
+ struct f81534_port_private *port_priv;
+ struct usb_serial *serial;
+ const struct f81534_port_out_pin *pins;
+ int status;
+ int i;
+ u8 value;
+ u8 idx;
+
+ serial = port->serial;
+ serial_priv = usb_get_serial_data(serial);
+ port_priv = usb_get_serial_port_data(port);
+
+ idx = F81534_CONF_GPIO_OFFSET + port_priv->phy_num;
+ value = serial_priv->conf_data[idx];
+ pins = &f81534_port_out_pins[port_priv->phy_num];
+
+ for (i = 0; i < ARRAY_SIZE(pins->pin); ++i) {
+ status = f81534_set_mask_register(serial,
+ pins->pin[i].reg_addr, pins->pin[i].reg_mask,
+ value & BIT(i) ? pins->pin[i].reg_mask : 0);
+ if (status)
+ return status;
+ }
+
+ dev_dbg(&port->dev, "Output pin (M0/M1/M2): %d\n", value);
+ return 0;
+}
+
static int f81534_port_probe(struct usb_serial_port *port)
{
struct f81534_serial_private *serial_priv;
@@ -1339,7 +1404,7 @@ static int f81534_port_probe(struct usb_serial_port *port)
break;
}
- return 0;
+ return f81534_set_port_output_pin(port);
}
static int f81534_port_remove(struct usb_serial_port *port)
--
2.7.4
The F81532/534 had auto RTS direction support for RS485 mode.
We'll read it from internal Flash with address 0x2f01~0x2f04 for 4 ports.
There are 4 conditions below:
0: F81534_PORT_CONF_RS232.
1: F81534_PORT_CONF_RS485.
2: value error, default to F81534_PORT_CONF_RS232.
3: F81534_PORT_CONF_RS485_INVERT.
F81532/534 Clock register (offset +08h)
Bit0: UART Enable (always on)
Bit2-1: Clock source selector
00: 1.846MHz.
01: 18.46MHz.
10: 24MHz.
11: 14.77MHz.
Bit4: Auto direction(RTS) control (RTS pin Low when TX)
Bit5: Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)
Signed-off-by: Ji-Ze Hong (Peter Hong) <[email protected]>
---
V3:
1: change some BIT() operation to GENMASK().
2: change some dev_info() to dev_dbg().
V2:
1: Read the configure data from flash and save it to shadow clock
register.
drivers/usb/serial/f81534.c | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c
index 1563d3f34381..2201be577dd3 100644
--- a/drivers/usb/serial/f81534.c
+++ b/drivers/usb/serial/f81534.c
@@ -98,11 +98,16 @@
#define F81534_DEFAULT_BAUD_RATE 9600
+#define F81534_PORT_CONF_RS232 0
+#define F81534_PORT_CONF_RS485 BIT(0)
+#define F81534_PORT_CONF_RS485_INVERT GENMASK(1, 0)
#define F81534_PORT_CONF_DISABLE_PORT BIT(3)
#define F81534_PORT_CONF_NOT_EXIST_PORT BIT(7)
#define F81534_PORT_UNAVAILABLE \
(F81534_PORT_CONF_DISABLE_PORT | F81534_PORT_CONF_NOT_EXIST_PORT)
+#define F81534_UART_MODE_MASK GENMASK(1, 0)
+
#define F81534_1X_RXTRIGGER 0xc3
#define F81534_8X_RXTRIGGER 0xcf
@@ -115,6 +120,8 @@
* 01: 18.46MHz.
* 10: 24MHz.
* 11: 14.77MHz.
+ * Bit4: Auto direction(RTS) control (RTS pin Low when TX)
+ * Bit5: Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)
*/
#define F81534_UART_EN BIT(0)
@@ -123,6 +130,8 @@
#define F81534_CLK_24_MHZ BIT(2)
#define F81534_CLK_14_77_MHZ GENMASK(2, 1)
#define F81534_CLK_MASK GENMASK(2, 1)
+#define F81534_CLK_RS485_MODE BIT(4)
+#define F81534_CLK_RS485_INVERT BIT(5)
static const struct usb_device_id f81534_id_table[] = {
{ USB_DEVICE(FINTEK_VENDOR_ID_1, FINTEK_DEVICE_ID) },
@@ -1274,9 +1283,12 @@ static void f81534_lsr_worker(struct work_struct *work)
static int f81534_port_probe(struct usb_serial_port *port)
{
+ struct f81534_serial_private *serial_priv;
struct f81534_port_private *port_priv;
int ret;
+ u8 value;
+ serial_priv = usb_get_serial_data(port->serial);
port_priv = devm_kzalloc(&port->dev, sizeof(*port_priv), GFP_KERNEL);
if (!port_priv)
return -ENOMEM;
@@ -1309,6 +1321,24 @@ static int f81534_port_probe(struct usb_serial_port *port)
if (ret)
return ret;
+ value = serial_priv->conf_data[port_priv->phy_num];
+ switch (value & F81534_UART_MODE_MASK) {
+ case F81534_PORT_CONF_RS485_INVERT:
+ port_priv->shadow_clk |= F81534_CLK_RS485_MODE |
+ F81534_CLK_RS485_INVERT;
+ dev_dbg(&port->dev, "RS485 invert mode.\n");
+ break;
+ case F81534_PORT_CONF_RS485:
+ port_priv->shadow_clk |= F81534_CLK_RS485_MODE;
+ dev_dbg(&port->dev, "RS485 mode.\n");
+ break;
+
+ default:
+ case F81534_PORT_CONF_RS232:
+ dev_dbg(&port->dev, "RS232 mode.\n");
+ break;
+ }
+
return 0;
}
--
2.7.4
On Thu, Jan 11, 2018 at 02:47:16PM +0800, Ji-Ze Hong (Peter Hong) wrote:
> The F81532/534 had auto RTS direction support for RS485 mode.
> We'll read it from internal Flash with address 0x2f01~0x2f04 for 4 ports.
> There are 4 conditions below:
> 0: F81534_PORT_CONF_RS232.
> 1: F81534_PORT_CONF_RS485.
> 2: value error, default to F81534_PORT_CONF_RS232.
> 3: F81534_PORT_CONF_RS485_INVERT.
>
> F81532/534 Clock register (offset +08h)
>
> Bit0: UART Enable (always on)
> Bit2-1: Clock source selector
> 00: 1.846MHz.
> 01: 18.46MHz.
> 10: 24MHz.
> 11: 14.77MHz.
> Bit4: Auto direction(RTS) control (RTS pin Low when TX)
> Bit5: Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)
>
> Signed-off-by: Ji-Ze Hong (Peter Hong) <[email protected]>
> ---
> V3:
> 1: change some BIT() operation to GENMASK().
> 2: change some dev_info() to dev_dbg().
>
> V2:
> 1: Read the configure data from flash and save it to shadow clock
> register.
Series now applied with a few minor tweaks.
> +#define F81534_PORT_CONF_RS232 0
> +#define F81534_PORT_CONF_RS485 BIT(0)
> +#define F81534_PORT_CONF_RS485_INVERT GENMASK(1, 0)
I replaced GENMASK() with your original (BIT(x) | BIT(y)) for register
values like this one.
> #define F81534_PORT_CONF_DISABLE_PORT BIT(3)
> #define F81534_PORT_CONF_NOT_EXIST_PORT BIT(7)
> #define F81534_PORT_UNAVAILABLE \
> (F81534_PORT_CONF_DISABLE_PORT | F81534_PORT_CONF_NOT_EXIST_PORT)
>
> +#define F81534_UART_MODE_MASK GENMASK(1, 0)
And renamed this mask to F81534_PORT_CONF_MODE_MASK so its more
obvious to what it applies.
Thanks,
Johan