From: Stefan Chulski <[email protected]>
Armada hardware has a pause generation mechanism in GOP (MAC).
The GOP generate flow control frames based on an indication programmed in Ports Control 0 Register. There is a bit per port.
However assertion of the PortX Pause bits in the ports control 0 register only sends a one time pause.
To complement the function the GOP has a mechanism to periodically send pause control messages based on periodic counters.
This mechanism ensures that the pause is effective as long as the Appropriate PortX Pause is asserted.
Problem is that Packet Processor that actually can drop packets due to lack of resources not connected to the GOP flow control generation mechanism.
To solve this issue Armada has firmware running on CM3 CPU dedicated for Flow Control support.
Firmware monitors Packet Processor resources and asserts XON/XOFF by writing to Ports Control 0 Register.
MSS shared SRAM memory used to communicate between CM3 firmware and PP2 driver.
During init PP2 driver informs firmware about used BM pools, RXQs, congestion and depletion thresholds.
The pause frames are generated whenever congestion or depletion in resources is detected.
The back pressure is stopped when the resource reaches a sufficient level.
So the congestion/depletion and sufficient level implement a hysteresis that reduces the XON/XOFF toggle frequency.
Packet Processor v23 hardware introduces support for RX FIFO fill level monitor.
Patch "add PPv23 version definition" to differ between v23 and v22 hardware.
Patch "add TX FC firmware check" verifies that CM3 firmware supports Flow Control monitoring.
v7 --> v8
- Reorder "always compare hw-version vs MVPP21" and "add PPv23 version definition" commits
- Typo fixes
- Remove condition fix from "add RXQ flow control configurations"
v6 --> v7
- Reduce patch set from 18 to 15 patches
- Documentation change combined into a single patch
- RXQ and BM size change combined into a single patch
- Ring size change check moved into "add RXQ flow control configurations" commit
v5 --> v6
- No change
v4 --> v5
- Add missed Signed-off
- Fix warnings in patches 3 and 12
- Add revision requirement to warning message
- Move mss_spinlock into RXQ flow control configurations patch
- Improve FCA RXQ non occupied descriptor threshold commit message
v3 --> v4
- Remove RFC tag
v2 --> v3
- Remove inline functions
- Add PPv2.3 description into marvell-pp2.txt
- Improve mvpp2_interrupts_mask/unmask procedure
- Improve FC enable/disable procedure
- Add priv->sram_pool check
- Remove gen_pool_destroy call
- Reduce Flow Control timer to x100 faster
v1 --> v2
- Add memory requirements information
- Add EPROBE_DEFER if of_gen_pool_get return NULL
- Move Flow control configuration to mvpp2_mac_link_up callback
- Add firmware version info with Flow control support
Konstantin Porotchkin (1):
dts: marvell: add CM3 SRAM memory to cp11x ethernet device tree
Stefan Chulski (14):
doc: marvell: add cm3-mem and PPv2.3 description
net: mvpp2: add CM3 SRAM memory map
net: mvpp2: always compare hw-version vs MVPP21
net: mvpp2: add PPv23 version definition
net: mvpp2: increase BM pool and RXQ size
net: mvpp2: add FCA periodic timer configurations
net: mvpp2: add FCA RXQ non occupied descriptor threshold
net: mvpp2: enable global flow control
net: mvpp2: add RXQ flow control configurations
net: mvpp2: add ethtool flow control configuration support
net: mvpp2: add BM protection underrun feature support
net: mvpp2: add PPv23 RX FIFO flow control
net: mvpp2: set 802.3x GoP Flow Control mode
net: mvpp2: add TX FC firmware check
Documentation/devicetree/bindings/net/marvell-pp2.txt | 4 +-
arch/arm64/boot/dts/marvell/armada-cp11x.dtsi | 10 +
drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 128 ++++-
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 563 ++++++++++++++++++--
4 files changed, 655 insertions(+), 50 deletions(-)
--
1.9.1
From: Stefan Chulski <[email protected]>
Patch introduce cm3-mem device tree bindings and add PPv2.3 description.
Signed-off-by: Stefan Chulski <[email protected]>
---
Documentation/devicetree/bindings/net/marvell-pp2.txt | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt
index b783976..df80cff 100644
--- a/Documentation/devicetree/bindings/net/marvell-pp2.txt
+++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt
@@ -1,5 +1,6 @@
* Marvell Armada 375 Ethernet Controller (PPv2.1)
Marvell Armada 7K/8K Ethernet Controller (PPv2.2)
+ Marvell CN913X Ethernet Controller (PPv2.3)
Required properties:
@@ -12,7 +13,7 @@ Required properties:
- common controller registers
- LMS registers
- one register area per Ethernet port
- For "marvell,armada-7k-pp2", must contain the following register
+ For "marvell,armada-7k-pp2" used by 7K/8K and CN913X, must contain the following register
sets:
- packet processor registers
- networking interfaces registers
@@ -37,6 +38,7 @@ Required properties (port):
GOP (Group Of Ports) point of view. This ID is used to index the
per-port registers in the second register area.
- phy-mode: See ethernet.txt file in the same directory
+- cm3-mem: phandle to CM3 SRAM definitions
Optional properties (port):
--
1.9.1
From: Stefan Chulski <[email protected]>
This patch add PPv23 version definition.
PPv23 is new packet processor in CP115.
Everything that supported by PPv22, also supported by PPv23.
No functional changes in this stage.
Signed-off-by: Stefan Chulski <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 24 ++++++++++++--------
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 17 +++++++++-----
2 files changed, 25 insertions(+), 16 deletions(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index aec9179..89b3ede 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -60,6 +60,9 @@
/* Top Registers */
#define MVPP2_MH_REG(port) (0x5040 + 4 * (port))
#define MVPP2_DSA_EXTENDED BIT(5)
+#define MVPP2_VER_ID_REG 0x50b0
+#define MVPP2_VER_PP22 0x10
+#define MVPP2_VER_PP23 0x11
/* Parser Registers */
#define MVPP2_PRS_INIT_LOOKUP_REG 0x1000
@@ -469,7 +472,7 @@
#define MVPP22_GMAC_INT_SUM_MASK_LINK_STAT BIT(1)
#define MVPP22_GMAC_INT_SUM_MASK_PTP BIT(2)
-/* Per-port XGMAC registers. PPv2.2 only, only for GOP port 0,
+/* Per-port XGMAC registers. PPv2.2 and PPv2.3, only for GOP port 0,
* relative to port->base.
*/
#define MVPP22_XLG_CTRL0_REG 0x100
@@ -506,7 +509,7 @@
#define MVPP22_XLG_CTRL4_MACMODSELECT_GMAC BIT(12)
#define MVPP22_XLG_CTRL4_EN_IDLE_CHECK BIT(14)
-/* SMI registers. PPv2.2 only, relative to priv->iface_base. */
+/* SMI registers. PPv2.2 and PPv2.3, relative to priv->iface_base. */
#define MVPP22_SMI_MISC_CFG_REG 0x1204
#define MVPP22_SMI_POLLING_EN BIT(10)
@@ -582,7 +585,7 @@
#define MVPP2_QUEUE_NEXT_DESC(q, index) \
(((index) < (q)->last_desc) ? ((index) + 1) : 0)
-/* XPCS registers. PPv2.2 only */
+/* XPCS registers.PPv2.2 and PPv2.3 */
#define MVPP22_MPCS_BASE(port) (0x7000 + (port) * 0x1000)
#define MVPP22_MPCS_CTRL 0x14
#define MVPP22_MPCS_CTRL_FWD_ERR_CONN BIT(10)
@@ -593,7 +596,7 @@
#define MVPP22_MPCS_CLK_RESET_DIV_RATIO(n) ((n) << 4)
#define MVPP22_MPCS_CLK_RESET_DIV_SET BIT(11)
-/* XPCS registers. PPv2.2 only */
+/* XPCS registers. PPv2.2 and PPv2.3 */
#define MVPP22_XPCS_BASE(port) (0x7400 + (port) * 0x1000)
#define MVPP22_XPCS_CFG0 0x0
#define MVPP22_XPCS_CFG0_RESET_DIS BIT(0)
@@ -930,15 +933,16 @@ struct mvpp2 {
void __iomem *iface_base;
void __iomem *cm3_base;
- /* On PPv2.2, each "software thread" can access the base
+ /* On PPv2.2 and PPv2.3, each "software thread" can access the base
* register through a separate address space, each 64 KB apart
* from each other. Typically, such address spaces will be
* used per CPU.
*/
void __iomem *swth_base[MVPP2_MAX_THREADS];
- /* On PPv2.2, some port control registers are located into the system
- * controller space. These registers are accessible through a regmap.
+ /* On PPv2.2 and PPv2.3, some port control registers are located into
+ * the system controller space. These registers are accessible
+ * through a regmap.
*/
struct regmap *sysctrl_base;
@@ -980,7 +984,7 @@ struct mvpp2 {
u32 tclk;
/* HW version */
- enum { MVPP21, MVPP22 } hw_version;
+ enum { MVPP21, MVPP22, MVPP23 } hw_version;
/* Maximum number of RXQs per port */
unsigned int max_port_rxqs;
@@ -1227,7 +1231,7 @@ struct mvpp21_rx_desc {
__le32 reserved8;
};
-/* HW TX descriptor for PPv2.2 */
+/* HW TX descriptor for PPv2.2 and PPv2.3 */
struct mvpp22_tx_desc {
__le32 command;
u8 packet_offset;
@@ -1239,7 +1243,7 @@ struct mvpp22_tx_desc {
__le64 buf_cookie_misc;
};
-/* HW RX descriptor for PPv2.2 */
+/* HW RX descriptor for PPv2.2 and PPv2.3 */
struct mvpp22_rx_desc {
__le32 status;
__le16 reserved1;
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 2c9da52..d80947a 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -385,7 +385,7 @@ static int mvpp2_bm_pool_create(struct device *dev, struct mvpp2 *priv,
if (!IS_ALIGNED(size, 16))
return -EINVAL;
- /* PPv2.1 needs 8 bytes per buffer pointer, PPv2.2 needs 16
+ /* PPv2.1 needs 8 bytes per buffer pointer, PPv2.2 and PPv2.3 needs 16
* bytes per buffer pointer
*/
if (priv->hw_version == MVPP21)
@@ -1173,7 +1173,7 @@ static void mvpp2_interrupts_unmask(void *arg)
u32 val;
int i;
- if (port->priv->hw_version != MVPP22)
+ if (port->priv->hw_version == MVPP21)
return;
if (mask)
@@ -5457,7 +5457,7 @@ static void mvpp2_rx_irqs_setup(struct mvpp2_port *port)
return;
}
- /* Handle the more complicated PPv2.2 case */
+ /* Handle the more complicated PPv2.2 and PPv2.3 case */
for (i = 0; i < port->nqvecs; i++) {
struct mvpp2_queue_vector *qv = port->qvecs + i;
@@ -5634,7 +5634,7 @@ static bool mvpp22_port_has_legacy_tx_irqs(struct device_node *port_node,
/* Checks if the port dt description has the required Tx interrupts:
* - PPv2.1: there are no such interrupts.
- * - PPv2.2:
+ * - PPv2.2 and PPv2.3:
* - The old DTs have: "rx-shared", "tx-cpuX" with X in [0...3]
* - The new ones have: "hifX" with X in [0..8]
*
@@ -6622,7 +6622,7 @@ static void mvpp22_rx_fifo_set_hw(struct mvpp2 *priv, int port, int data_size)
mvpp2_write(priv, MVPP2_RX_ATTR_FIFO_SIZE_REG(port), attr_size);
}
-/* Initialize TX FIFO's: the total FIFO size is 48kB on PPv2.2.
+/* Initialize TX FIFO's: the total FIFO size is 48kB on PPv2.2 and PPv2.3.
* 4kB fixed space must be assigned for the loopback port.
* Redistribute remaining avialable 44kB space among all active ports.
* Guarantee minimum 32kB for 10G port and 8kB for port 1, capable of 2.5G
@@ -6679,7 +6679,7 @@ static void mvpp22_tx_fifo_set_hw(struct mvpp2 *priv, int port, int size)
mvpp2_write(priv, MVPP22_TX_FIFO_THRESH_REG(port), threshold);
}
-/* Initialize TX FIFO's: the total FIFO size is 19kB on PPv2.2.
+/* Initialize TX FIFO's: the total FIFO size is 19kB on PPv2.2 and PPv2.3.
* 3kB fixed space must be assigned for the loopback port.
* Redistribute remaining avialable 16kB space among all active ports.
* The 10G interface should use 10kB (which is maximum possible size
@@ -7071,6 +7071,11 @@ static int mvpp2_probe(struct platform_device *pdev)
priv->port_map |= BIT(i);
}
+ if (priv->hw_version != MVPP21) {
+ if (mvpp2_read(priv, MVPP2_VER_ID_REG) == MVPP2_VER_PP23)
+ priv->hw_version = MVPP23;
+ }
+
/* Initialize network controller */
err = mvpp2_init(pdev, priv);
if (err < 0) {
--
1.9.1
From: Stefan Chulski <[email protected]>
Currently we have PP2v1 and PP2v2 hw-versions, with some different
handlers depending upon condition hw_version = MVPP21/MVPP22.
In a future there will be also PP2v3. Let's use now the generic
"if equal/notEqual MVPP21" for all cases instead of "if MVPP22".
This patch does not change any functionality.
It is not intended to introduce PP2v3.
It just modifies MVPP21/MVPP22 check-condition
bringing it to generic and unified form correct for new-code
introducing and PP2v3 net-next generation.
Signed-off-by: Stefan Chulski <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 36 ++++++++++----------
1 file changed, 18 insertions(+), 18 deletions(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 307f9fd..2c9da52 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -320,7 +320,7 @@ static int mvpp2_get_nrxqs(struct mvpp2 *priv)
{
unsigned int nrxqs;
- if (priv->hw_version == MVPP22 && queue_mode == MVPP2_QDIST_SINGLE_MODE)
+ if (priv->hw_version != MVPP21 && queue_mode == MVPP2_QDIST_SINGLE_MODE)
return 1;
/* According to the PPv2.2 datasheet and our experiments on
@@ -447,7 +447,7 @@ static void mvpp2_bm_bufs_get_addrs(struct device *dev, struct mvpp2 *priv,
MVPP2_BM_PHY_ALLOC_REG(bm_pool->id));
*phys_addr = mvpp2_thread_read(priv, thread, MVPP2_BM_VIRT_ALLOC_REG);
- if (priv->hw_version == MVPP22) {
+ if (priv->hw_version != MVPP21) {
u32 val;
u32 dma_addr_highbits, phys_addr_highbits;
@@ -743,7 +743,7 @@ static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
if (test_bit(thread, &port->priv->lock_map))
spin_lock_irqsave(&port->bm_lock[thread], flags);
- if (port->priv->hw_version == MVPP22) {
+ if (port->priv->hw_version != MVPP21) {
u32 val = 0;
if (sizeof(dma_addr_t) == 8)
@@ -1200,7 +1200,7 @@ static bool mvpp2_port_supports_xlg(struct mvpp2_port *port)
static bool mvpp2_port_supports_rgmii(struct mvpp2_port *port)
{
- return !(port->priv->hw_version == MVPP22 && port->gop_id == 0);
+ return !(port->priv->hw_version != MVPP21 && port->gop_id == 0);
}
/* Port configuration routines */
@@ -1818,7 +1818,7 @@ static void mvpp2_mac_reset_assert(struct mvpp2_port *port)
MVPP2_GMAC_PORT_RESET_MASK;
writel(val, port->base + MVPP2_GMAC_CTRL_2_REG);
- if (port->priv->hw_version == MVPP22 && port->gop_id == 0) {
+ if (port->priv->hw_version != MVPP21 && port->gop_id == 0) {
val = readl(port->base + MVPP22_XLG_CTRL0_REG) &
~MVPP22_XLG_CTRL0_MAC_RESET_DIS;
writel(val, port->base + MVPP22_XLG_CTRL0_REG);
@@ -1831,7 +1831,7 @@ static void mvpp22_pcs_reset_assert(struct mvpp2_port *port)
void __iomem *mpcs, *xpcs;
u32 val;
- if (port->priv->hw_version != MVPP22 || port->gop_id != 0)
+ if (port->priv->hw_version == MVPP21 || port->gop_id != 0)
return;
mpcs = priv->iface_base + MVPP22_MPCS_BASE(port->gop_id);
@@ -1852,7 +1852,7 @@ static void mvpp22_pcs_reset_deassert(struct mvpp2_port *port)
void __iomem *mpcs, *xpcs;
u32 val;
- if (port->priv->hw_version != MVPP22 || port->gop_id != 0)
+ if (port->priv->hw_version == MVPP21 || port->gop_id != 0)
return;
mpcs = priv->iface_base + MVPP22_MPCS_BASE(port->gop_id);
@@ -4189,7 +4189,7 @@ static void mvpp2_start_dev(struct mvpp2_port *port)
/* Enable interrupts on all threads */
mvpp2_interrupts_enable(port);
- if (port->priv->hw_version == MVPP22)
+ if (port->priv->hw_version != MVPP21)
mvpp22_mode_reconfigure(port);
if (port->phylink) {
@@ -4405,7 +4405,7 @@ static int mvpp2_open(struct net_device *dev)
valid = true;
}
- if (priv->hw_version == MVPP22 && port->port_irq) {
+ if (priv->hw_version != MVPP21 && port->port_irq) {
err = request_irq(port->port_irq, mvpp2_port_isr, 0,
dev->name, port);
if (err) {
@@ -6053,7 +6053,7 @@ static int mvpp2__mac_prepare(struct phylink_config *config, unsigned int mode,
MVPP2_GMAC_PORT_RESET_MASK,
MVPP2_GMAC_PORT_RESET_MASK);
- if (port->priv->hw_version == MVPP22) {
+ if (port->priv->hw_version != MVPP21) {
mvpp22_gop_mask_irq(port);
phy_power_off(port->comphy);
@@ -6107,7 +6107,7 @@ static int mvpp2_mac_finish(struct phylink_config *config, unsigned int mode,
{
struct mvpp2_port *port = mvpp2_phylink_to_port(config);
- if (port->priv->hw_version == MVPP22 &&
+ if (port->priv->hw_version != MVPP21 &&
port->phy_interface != interface) {
port->phy_interface = interface;
@@ -6787,7 +6787,7 @@ static int mvpp2_init(struct platform_device *pdev, struct mvpp2 *priv)
if (dram_target_info)
mvpp2_conf_mbus_windows(dram_target_info, priv);
- if (priv->hw_version == MVPP22)
+ if (priv->hw_version != MVPP21)
mvpp2_axi_init(priv);
/* Disable HW PHY polling */
@@ -6950,7 +6950,7 @@ static int mvpp2_probe(struct platform_device *pdev)
dev_warn(&pdev->dev, "Fail to alloc CM3 SRAM\n");
}
- if (priv->hw_version == MVPP22 && dev_of_node(&pdev->dev)) {
+ if (priv->hw_version != MVPP21 && dev_of_node(&pdev->dev)) {
priv->sysctrl_base =
syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
"marvell,system-controller");
@@ -6963,7 +6963,7 @@ static int mvpp2_probe(struct platform_device *pdev)
priv->sysctrl_base = NULL;
}
- if (priv->hw_version == MVPP22 &&
+ if (priv->hw_version != MVPP21 &&
mvpp2_get_nrxqs(priv) * 2 <= MVPP2_BM_MAX_POOLS)
priv->percpu_pools = 1;
@@ -7010,7 +7010,7 @@ static int mvpp2_probe(struct platform_device *pdev)
if (err < 0)
goto err_pp_clk;
- if (priv->hw_version == MVPP22) {
+ if (priv->hw_version != MVPP21) {
priv->mg_clk = devm_clk_get(&pdev->dev, "mg_clk");
if (IS_ERR(priv->mg_clk)) {
err = PTR_ERR(priv->mg_clk);
@@ -7051,7 +7051,7 @@ static int mvpp2_probe(struct platform_device *pdev)
return -EINVAL;
}
- if (priv->hw_version == MVPP22) {
+ if (priv->hw_version != MVPP21) {
err = dma_set_mask(&pdev->dev, MVPP2_DESC_DMA_MASK);
if (err)
goto err_axi_clk;
@@ -7126,10 +7126,10 @@ static int mvpp2_probe(struct platform_device *pdev)
clk_disable_unprepare(priv->axi_clk);
err_mg_core_clk:
- if (priv->hw_version == MVPP22)
+ if (priv->hw_version != MVPP21)
clk_disable_unprepare(priv->mg_core_clk);
err_mg_clk:
- if (priv->hw_version == MVPP22)
+ if (priv->hw_version != MVPP21)
clk_disable_unprepare(priv->mg_clk);
err_gop_clk:
clk_disable_unprepare(priv->gop_clk);
--
1.9.1
From: Konstantin Porotchkin <[email protected]>
CM3 SRAM address space would be used for Flow Control configuration.
Signed-off-by: Stefan Chulski <[email protected]>
Signed-off-by: Konstantin Porotchkin <[email protected]>
---
arch/arm64/boot/dts/marvell/armada-cp11x.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
index 9dcf16b..359cf42 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
@@ -69,6 +69,8 @@
status = "disabled";
dma-coherent;
+ cm3-mem = <&CP11X_LABEL(cm3_sram)>;
+
CP11X_LABEL(eth0): eth0 {
interrupts = <39 IRQ_TYPE_LEVEL_HIGH>,
<43 IRQ_TYPE_LEVEL_HIGH>,
@@ -211,6 +213,14 @@
};
};
+ CP11X_LABEL(cm3_sram): cm3@220000 {
+ compatible = "mmio-sram";
+ reg = <0x220000 0x800>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x220000 0x800>;
+ };
+
CP11X_LABEL(rtc): rtc@284000 {
compatible = "marvell,armada-8k-rtc";
reg = <0x284000 0x20>, <0x284080 0x24>;
--
1.9.1
From: Stefan Chulski <[email protected]>
This patch adds CM3 memory map and CM3 read/write callbacks.
No functionality changes.
Signed-off-by: Stefan Chulski <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 7 +++
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 63 +++++++++++++++++++-
2 files changed, 67 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 6bd7e40..aec9179 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -748,6 +748,9 @@
#define MVPP2_TX_FIFO_THRESHOLD(kb) \
((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
+/* MSS Flow control */
+#define MSS_SRAM_SIZE 0x800
+
/* RX buffer constants */
#define MVPP2_SKB_SHINFO_SIZE \
SKB_DATA_ALIGN(sizeof(struct skb_shared_info))
@@ -925,6 +928,7 @@ struct mvpp2 {
/* Shared registers' base addresses */
void __iomem *lms_base;
void __iomem *iface_base;
+ void __iomem *cm3_base;
/* On PPv2.2, each "software thread" can access the base
* register through a separate address space, each 64 KB apart
@@ -996,6 +1000,9 @@ struct mvpp2 {
/* page_pool allocator */
struct page_pool *page_pool[MVPP2_PORT_MAX_RXQ];
+
+ /* CM3 SRAM pool */
+ struct gen_pool *sram_pool;
};
struct mvpp2_pcpu_stats {
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index a07cf60..307f9fd 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -25,6 +25,7 @@
#include <linux/of_net.h>
#include <linux/of_address.h>
#include <linux/of_device.h>
+#include <linux/genalloc.h>
#include <linux/phy.h>
#include <linux/phylink.h>
#include <linux/phy/phy.h>
@@ -6846,6 +6847,44 @@ static int mvpp2_init(struct platform_device *pdev, struct mvpp2 *priv)
return 0;
}
+static int mvpp2_get_sram(struct platform_device *pdev,
+ struct mvpp2 *priv)
+{
+ struct device_node *dn = pdev->dev.of_node;
+ static bool defer_once;
+ struct resource *res;
+
+ if (has_acpi_companion(&pdev->dev)) {
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+ if (!res) {
+ dev_warn(&pdev->dev, "ACPI is too old, Flow control not supported\n");
+ return 0;
+ }
+ priv->cm3_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(priv->cm3_base))
+ return PTR_ERR(priv->cm3_base);
+ } else {
+ priv->sram_pool = of_gen_pool_get(dn, "cm3-mem", 0);
+ if (!priv->sram_pool) {
+ if (!defer_once) {
+ defer_once = true;
+ /* Try defer once */
+ return -EPROBE_DEFER;
+ }
+ dev_warn(&pdev->dev, "DT is too old, Flow control not supported\n");
+ return -ENOMEM;
+ }
+ /* cm3_base allocated with offset zero into the SRAM since mapping size
+ * is equal to requested size.
+ */
+ priv->cm3_base = (void __iomem *)gen_pool_alloc(priv->sram_pool,
+ MSS_SRAM_SIZE);
+ if (!priv->cm3_base)
+ return -ENOMEM;
+ }
+ return 0;
+}
+
static int mvpp2_probe(struct platform_device *pdev)
{
const struct acpi_device_id *acpi_id;
@@ -6902,6 +6941,13 @@ static int mvpp2_probe(struct platform_device *pdev)
priv->iface_base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(priv->iface_base))
return PTR_ERR(priv->iface_base);
+
+ /* Map CM3 SRAM */
+ err = mvpp2_get_sram(pdev, priv);
+ if (err == -EPROBE_DEFER)
+ return err;
+ else if (err)
+ dev_warn(&pdev->dev, "Fail to alloc CM3 SRAM\n");
}
if (priv->hw_version == MVPP22 && dev_of_node(&pdev->dev)) {
@@ -6947,11 +6993,13 @@ static int mvpp2_probe(struct platform_device *pdev)
if (dev_of_node(&pdev->dev)) {
priv->pp_clk = devm_clk_get(&pdev->dev, "pp_clk");
- if (IS_ERR(priv->pp_clk))
- return PTR_ERR(priv->pp_clk);
+ if (IS_ERR(priv->pp_clk)) {
+ err = PTR_ERR(priv->pp_clk);
+ goto err_cm3;
+ }
err = clk_prepare_enable(priv->pp_clk);
if (err < 0)
- return err;
+ goto err_cm3;
priv->gop_clk = devm_clk_get(&pdev->dev, "gop_clk");
if (IS_ERR(priv->gop_clk)) {
@@ -7087,6 +7135,11 @@ static int mvpp2_probe(struct platform_device *pdev)
clk_disable_unprepare(priv->gop_clk);
err_pp_clk:
clk_disable_unprepare(priv->pp_clk);
+err_cm3:
+ if (priv->sram_pool && priv->cm3_base)
+ gen_pool_free(priv->sram_pool, (unsigned long)priv->cm3_base,
+ MSS_SRAM_SIZE);
+
return err;
}
@@ -7127,6 +7180,10 @@ static int mvpp2_remove(struct platform_device *pdev)
aggr_txq->descs_dma);
}
+ if (priv->sram_pool && priv->cm3_base)
+ gen_pool_free(priv->sram_pool, (unsigned long)priv->cm3_base,
+ MSS_SRAM_SIZE);
+
if (is_acpi_node(port_fwnode))
return 0;
--
1.9.1
From: Stefan Chulski <[email protected]>
BM pool and RXQ size increased to support Firmware Flow Control.
Minimum depletion thresholds to support FC are 1024 buffers.
BM pool size increased to 2048 to have some 1024 buffers
space between depletion thresholds and BM pool size.
Jumbo frames require a 9888B buffer, so memory requirements
for data buffers increased from 7MB to 24MB.
Signed-off-by: Stefan Chulski <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 89b3ede..cac9885 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -715,8 +715,8 @@
#define MVPP2_PORT_MAX_RXQ 32
/* Max number of Rx descriptors */
-#define MVPP2_MAX_RXD_MAX 1024
-#define MVPP2_MAX_RXD_DFLT 128
+#define MVPP2_MAX_RXD_MAX 2048
+#define MVPP2_MAX_RXD_DFLT 1024
/* Max number of Tx descriptors */
#define MVPP2_MAX_TXD_MAX 2048
@@ -851,8 +851,8 @@ enum mvpp22_ptp_packet_format {
#define MVPP22_PTP_TIMESTAMPQUEUESELECT BIT(18)
/* BM constants */
-#define MVPP2_BM_JUMBO_BUF_NUM 512
-#define MVPP2_BM_LONG_BUF_NUM 1024
+#define MVPP2_BM_JUMBO_BUF_NUM 2048
+#define MVPP2_BM_LONG_BUF_NUM 2048
#define MVPP2_BM_SHORT_BUF_NUM 2048
#define MVPP2_BM_POOL_SIZE_MAX (16*1024 - MVPP2_BM_POOL_PTR_ALIGN/4)
#define MVPP2_BM_POOL_PTR_ALIGN 128
--
1.9.1
From: Stefan Chulski <[email protected]>
Flow Control periodic timer would be used if port in
XOFF to transmit periodic XOFF frames.
Signed-off-by: Stefan Chulski <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 13 +++++-
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 45 ++++++++++++++++++++
2 files changed, 57 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index cac9885..73f087c 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -596,6 +596,15 @@
#define MVPP22_MPCS_CLK_RESET_DIV_RATIO(n) ((n) << 4)
#define MVPP22_MPCS_CLK_RESET_DIV_SET BIT(11)
+/* FCA registers. PPv2.2 and PPv2.3 */
+#define MVPP22_FCA_BASE(port) (0x7600 + (port) * 0x1000)
+#define MVPP22_FCA_REG_SIZE 16
+#define MVPP22_FCA_REG_MASK 0xFFFF
+#define MVPP22_FCA_CONTROL_REG 0x0
+#define MVPP22_FCA_ENABLE_PERIODIC BIT(11)
+#define MVPP22_PERIODIC_COUNTER_LSB_REG (0x110)
+#define MVPP22_PERIODIC_COUNTER_MSB_REG (0x114)
+
/* XPCS registers. PPv2.2 and PPv2.3 */
#define MVPP22_XPCS_BASE(port) (0x7400 + (port) * 0x1000)
#define MVPP22_XPCS_CFG0 0x0
@@ -752,7 +761,9 @@
((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
/* MSS Flow control */
-#define MSS_SRAM_SIZE 0x800
+#define MSS_SRAM_SIZE 0x800
+#define FC_QUANTA 0xFFFF
+#define FC_CLK_DIVIDER 100
/* RX buffer constants */
#define MVPP2_SKB_SHINFO_SIZE \
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index d80947a..6e59d07 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -1281,6 +1281,49 @@ static void mvpp22_gop_init_10gkr(struct mvpp2_port *port)
writel(val, mpcs + MVPP22_MPCS_CLK_RESET);
}
+static void mvpp22_gop_fca_enable_periodic(struct mvpp2_port *port, bool en)
+{
+ struct mvpp2 *priv = port->priv;
+ void __iomem *fca = priv->iface_base + MVPP22_FCA_BASE(port->gop_id);
+ u32 val;
+
+ val = readl(fca + MVPP22_FCA_CONTROL_REG);
+ val &= ~MVPP22_FCA_ENABLE_PERIODIC;
+ if (en)
+ val |= MVPP22_FCA_ENABLE_PERIODIC;
+ writel(val, fca + MVPP22_FCA_CONTROL_REG);
+}
+
+static void mvpp22_gop_fca_set_timer(struct mvpp2_port *port, u32 timer)
+{
+ struct mvpp2 *priv = port->priv;
+ void __iomem *fca = priv->iface_base + MVPP22_FCA_BASE(port->gop_id);
+ u32 lsb, msb;
+
+ lsb = timer & MVPP22_FCA_REG_MASK;
+ msb = timer >> MVPP22_FCA_REG_SIZE;
+
+ writel(lsb, fca + MVPP22_PERIODIC_COUNTER_LSB_REG);
+ writel(msb, fca + MVPP22_PERIODIC_COUNTER_MSB_REG);
+}
+
+/* Set Flow Control timer x100 faster than pause quanta to ensure that link
+ * partner won't send traffic if port is in XOFF mode.
+ */
+static void mvpp22_gop_fca_set_periodic_timer(struct mvpp2_port *port)
+{
+ u32 timer;
+
+ timer = (port->priv->tclk / (USEC_PER_SEC * FC_CLK_DIVIDER))
+ * FC_QUANTA;
+
+ mvpp22_gop_fca_enable_periodic(port, false);
+
+ mvpp22_gop_fca_set_timer(port, timer);
+
+ mvpp22_gop_fca_enable_periodic(port, true);
+}
+
static int mvpp22_gop_init(struct mvpp2_port *port)
{
struct mvpp2 *priv = port->priv;
@@ -1325,6 +1368,8 @@ static int mvpp22_gop_init(struct mvpp2_port *port)
val |= GENCONF_SOFT_RESET1_GOP;
regmap_write(priv->sysctrl_base, GENCONF_SOFT_RESET1, val);
+ mvpp22_gop_fca_set_periodic_timer(port);
+
unsupported_conf:
return 0;
--
1.9.1
From: Stefan Chulski <[email protected]>
The firmware needs to monitor the RX Non-occupied descriptor
bits for flow control to move to XOFF mode.
These bits need to be unmasked to be functional, but they will
not raise interrupts as we leave the RX exception summary
bit in MVPP2_ISR_RX_TX_MASK_REG clear.
Signed-off-by: Stefan Chulski <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 3 ++
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 44 ++++++++++++++++----
2 files changed, 40 insertions(+), 7 deletions(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 73f087c..ca84995 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -295,6 +295,8 @@
#define MVPP2_PON_CAUSE_TXP_OCCUP_DESC_ALL_MASK 0x3fc00000
#define MVPP2_PON_CAUSE_MISC_SUM_MASK BIT(31)
#define MVPP2_ISR_MISC_CAUSE_REG 0x55b0
+#define MVPP2_ISR_RX_ERR_CAUSE_REG(port) (0x5520 + 4 * (port))
+#define MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK 0x00ff
/* Buffer Manager registers */
#define MVPP2_BM_POOL_BASE_REG(pool) (0x6000 + ((pool) * 4))
@@ -764,6 +766,7 @@
#define MSS_SRAM_SIZE 0x800
#define FC_QUANTA 0xFFFF
#define FC_CLK_DIVIDER 100
+#define MSS_THRESHOLD_STOP 768
/* RX buffer constants */
#define MVPP2_SKB_SHINFO_SIZE \
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 6e59d07..a72a390 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -1134,14 +1134,19 @@ static inline void mvpp2_qvec_interrupt_disable(struct mvpp2_queue_vector *qvec)
static void mvpp2_interrupts_mask(void *arg)
{
struct mvpp2_port *port = arg;
+ int cpu = smp_processor_id();
+ u32 thread;
/* If the thread isn't used, don't do anything */
- if (smp_processor_id() > port->priv->nthreads)
+ if (cpu > port->priv->nthreads)
return;
- mvpp2_thread_write(port->priv,
- mvpp2_cpu_to_thread(port->priv, smp_processor_id()),
+ thread = mvpp2_cpu_to_thread(port->priv, cpu);
+
+ mvpp2_thread_write(port->priv, thread,
MVPP2_ISR_RX_TX_MASK_REG(port->id), 0);
+ mvpp2_thread_write(port->priv, thread,
+ MVPP2_ISR_RX_ERR_CAUSE_REG(port->id), 0);
}
/* Unmask the current thread's Rx/Tx interrupts.
@@ -1151,20 +1156,25 @@ static void mvpp2_interrupts_mask(void *arg)
static void mvpp2_interrupts_unmask(void *arg)
{
struct mvpp2_port *port = arg;
- u32 val;
+ int cpu = smp_processor_id();
+ u32 val, thread;
/* If the thread isn't used, don't do anything */
- if (smp_processor_id() > port->priv->nthreads)
+ if (cpu > port->priv->nthreads)
return;
+ thread = mvpp2_cpu_to_thread(port->priv, cpu);
+
val = MVPP2_CAUSE_MISC_SUM_MASK |
MVPP2_CAUSE_RXQ_OCCUP_DESC_ALL_MASK(port->priv->hw_version);
if (port->has_tx_irqs)
val |= MVPP2_CAUSE_TXQ_OCCUP_DESC_ALL_MASK;
- mvpp2_thread_write(port->priv,
- mvpp2_cpu_to_thread(port->priv, smp_processor_id()),
+ mvpp2_thread_write(port->priv, thread,
MVPP2_ISR_RX_TX_MASK_REG(port->id), val);
+ mvpp2_thread_write(port->priv, thread,
+ MVPP2_ISR_RX_ERR_CAUSE_REG(port->id),
+ MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK);
}
static void
@@ -1189,6 +1199,9 @@ static void mvpp2_interrupts_unmask(void *arg)
mvpp2_thread_write(port->priv, v->sw_thread_id,
MVPP2_ISR_RX_TX_MASK_REG(port->id), val);
+ mvpp2_thread_write(port->priv, v->sw_thread_id,
+ MVPP2_ISR_RX_ERR_CAUSE_REG(port->id),
+ MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK);
}
}
@@ -2394,6 +2407,20 @@ static void mvpp2_txp_max_tx_size_set(struct mvpp2_port *port)
}
}
+/* Set the number of non-occupied descriptors threshold */
+static void mvpp2_set_rxq_free_tresh(struct mvpp2_port *port,
+ struct mvpp2_rx_queue *rxq)
+{
+ u32 val;
+
+ mvpp2_write(port->priv, MVPP2_RXQ_NUM_REG, rxq->id);
+
+ val = mvpp2_read(port->priv, MVPP2_RXQ_THRESH_REG);
+ val &= ~MVPP2_RXQ_NON_OCCUPIED_MASK;
+ val |= MSS_THRESHOLD_STOP << MVPP2_RXQ_NON_OCCUPIED_OFFSET;
+ mvpp2_write(port->priv, MVPP2_RXQ_THRESH_REG, val);
+}
+
/* Set the number of packets that will be received before Rx interrupt
* will be generated by HW.
*/
@@ -2649,6 +2676,9 @@ static int mvpp2_rxq_init(struct mvpp2_port *port,
mvpp2_rx_pkts_coal_set(port, rxq);
mvpp2_rx_time_coal_set(port, rxq);
+ /* Set the number of non occupied descriptors threshold */
+ mvpp2_set_rxq_free_tresh(port, rxq);
+
/* Add number of descriptors ready for receiving packets */
mvpp2_rxq_status_update(port, rxq->id, 0, rxq->size);
--
1.9.1
From: Stefan Chulski <[email protected]>
This patch adds RXQ flow control configurations.
Flow control disabled by default.
Minimum ring size limited to 1024 descriptors.
Signed-off-by: Stefan Chulski <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 35 +++++-
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 116 ++++++++++++++++++++
2 files changed, 150 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index e010410..0f27be0 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -766,9 +766,36 @@
#define MSS_SRAM_SIZE 0x800
#define MSS_FC_COM_REG 0
#define FLOW_CONTROL_ENABLE_BIT BIT(0)
+#define FLOW_CONTROL_UPDATE_COMMAND_BIT BIT(31)
#define FC_QUANTA 0xFFFF
#define FC_CLK_DIVIDER 100
-#define MSS_THRESHOLD_STOP 768
+
+#define MSS_RXQ_TRESH_BASE 0x200
+#define MSS_RXQ_TRESH_OFFS 4
+#define MSS_RXQ_TRESH_REG(q, fq) (MSS_RXQ_TRESH_BASE + (((q) + (fq)) \
+ * MSS_RXQ_TRESH_OFFS))
+
+#define MSS_RXQ_TRESH_START_MASK 0xFFFF
+#define MSS_RXQ_TRESH_STOP_MASK (0xFFFF << MSS_RXQ_TRESH_STOP_OFFS)
+#define MSS_RXQ_TRESH_STOP_OFFS 16
+
+#define MSS_RXQ_ASS_BASE 0x80
+#define MSS_RXQ_ASS_OFFS 4
+#define MSS_RXQ_ASS_PER_REG 4
+#define MSS_RXQ_ASS_PER_OFFS 8
+#define MSS_RXQ_ASS_PORTID_OFFS 0
+#define MSS_RXQ_ASS_PORTID_MASK 0x3
+#define MSS_RXQ_ASS_HOSTID_OFFS 2
+#define MSS_RXQ_ASS_HOSTID_MASK 0x3F
+
+#define MSS_RXQ_ASS_Q_BASE(q, fq) ((((q) + (fq)) % MSS_RXQ_ASS_PER_REG) \
+ * MSS_RXQ_ASS_PER_OFFS)
+#define MSS_RXQ_ASS_PQ_BASE(q, fq) ((((q) + (fq)) / MSS_RXQ_ASS_PER_REG) \
+ * MSS_RXQ_ASS_OFFS)
+#define MSS_RXQ_ASS_REG(q, fq) (MSS_RXQ_ASS_BASE + MSS_RXQ_ASS_PQ_BASE(q, fq))
+
+#define MSS_THRESHOLD_STOP 768
+#define MSS_THRESHOLD_START 1024
/* RX buffer constants */
#define MVPP2_SKB_SHINFO_SIZE \
@@ -1026,6 +1053,9 @@ struct mvpp2 {
/* Global TX Flow Control config */
bool global_tx_fc;
+
+ /* Spinlocks for CM3 shared memory configuration */
+ spinlock_t mss_spinlock;
};
struct mvpp2_pcpu_stats {
@@ -1188,6 +1218,9 @@ struct mvpp2_port {
bool rx_hwtstamp;
enum hwtstamp_tx_types tx_hwtstamp_type;
struct mvpp2_hwtstamp_queue tx_hwtstamp_queue[2];
+
+ /* Firmware TX flow control */
+ bool tx_fc;
};
/* The mvpp2_tx_desc and mvpp2_rx_desc structures describe the
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index fec1c81..29ba62a 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -742,6 +742,110 @@ static void *mvpp2_buf_alloc(struct mvpp2_port *port,
return data;
}
+/* Routine enable flow control for RXQs condition */
+static void mvpp2_rxq_enable_fc(struct mvpp2_port *port)
+{
+ int val, cm3_state, host_id, q;
+ int fq = port->first_rxq;
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->priv->mss_spinlock, flags);
+
+ /* Remove Flow control enable bit to prevent race between FW and Kernel
+ * If Flow control was enabled, it would be re-enabled.
+ */
+ val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+ cm3_state = (val & FLOW_CONTROL_ENABLE_BIT);
+ val &= ~FLOW_CONTROL_ENABLE_BIT;
+ mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+ /* Set same Flow control for all RXQs */
+ for (q = 0; q < port->nrxqs; q++) {
+ /* Set stop and start Flow control RXQ thresholds */
+ val = MSS_THRESHOLD_START;
+ val |= (MSS_THRESHOLD_STOP << MSS_RXQ_TRESH_STOP_OFFS);
+ mvpp2_cm3_write(port->priv, MSS_RXQ_TRESH_REG(q, fq), val);
+
+ val = mvpp2_cm3_read(port->priv, MSS_RXQ_ASS_REG(q, fq));
+ /* Set RXQ port ID */
+ val &= ~(MSS_RXQ_ASS_PORTID_MASK << MSS_RXQ_ASS_Q_BASE(q, fq));
+ val |= (port->id << MSS_RXQ_ASS_Q_BASE(q, fq));
+ val &= ~(MSS_RXQ_ASS_HOSTID_MASK << (MSS_RXQ_ASS_Q_BASE(q, fq)
+ + MSS_RXQ_ASS_HOSTID_OFFS));
+
+ /* Calculate RXQ host ID:
+ * In Single queue mode: Host ID equal to Host ID used for
+ * shared RX interrupt
+ * In Multi queue mode: Host ID equal to number of
+ * RXQ ID / number of CoS queues
+ * In Single resource mode: Host ID always equal to 0
+ */
+ if (queue_mode == MVPP2_QDIST_SINGLE_MODE)
+ host_id = port->nqvecs;
+ else if (queue_mode == MVPP2_QDIST_MULTI_MODE)
+ host_id = q;
+ else
+ host_id = 0;
+
+ /* Set RXQ host ID */
+ val |= (host_id << (MSS_RXQ_ASS_Q_BASE(q, fq)
+ + MSS_RXQ_ASS_HOSTID_OFFS));
+
+ mvpp2_cm3_write(port->priv, MSS_RXQ_ASS_REG(q, fq), val);
+ }
+
+ /* Notify Firmware that Flow control config space ready for update */
+ val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+ val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+ val |= cm3_state;
+ mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+ spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
+}
+
+/* Routine disable flow control for RXQs condition */
+static void mvpp2_rxq_disable_fc(struct mvpp2_port *port)
+{
+ int val, cm3_state, q;
+ unsigned long flags;
+ int fq = port->first_rxq;
+
+ spin_lock_irqsave(&port->priv->mss_spinlock, flags);
+
+ /* Remove Flow control enable bit to prevent race between FW and Kernel
+ * If Flow control was enabled, it would be re-enabled.
+ */
+ val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+ cm3_state = (val & FLOW_CONTROL_ENABLE_BIT);
+ val &= ~FLOW_CONTROL_ENABLE_BIT;
+ mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+ /* Disable Flow control for all RXQs */
+ for (q = 0; q < port->nrxqs; q++) {
+ /* Set threshold 0 to disable Flow control */
+ val = 0;
+ val |= (0 << MSS_RXQ_TRESH_STOP_OFFS);
+ mvpp2_cm3_write(port->priv, MSS_RXQ_TRESH_REG(q, fq), val);
+
+ val = mvpp2_cm3_read(port->priv, MSS_RXQ_ASS_REG(q, fq));
+
+ val &= ~(MSS_RXQ_ASS_PORTID_MASK << MSS_RXQ_ASS_Q_BASE(q, fq));
+
+ val &= ~(MSS_RXQ_ASS_HOSTID_MASK << (MSS_RXQ_ASS_Q_BASE(q, fq)
+ + MSS_RXQ_ASS_HOSTID_OFFS));
+
+ mvpp2_cm3_write(port->priv, MSS_RXQ_ASS_REG(q, fq), val);
+ }
+
+ /* Notify Firmware that Flow control config space ready for update */
+ val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+ val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+ val |= cm3_state;
+ mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+ spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
+}
+
/* Release buffer to BM */
static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
dma_addr_t buf_dma_addr,
@@ -3006,6 +3110,9 @@ static void mvpp2_cleanup_rxqs(struct mvpp2_port *port)
for (queue = 0; queue < port->nrxqs; queue++)
mvpp2_rxq_deinit(port, port->rxqs[queue]);
+
+ if (port->tx_fc)
+ mvpp2_rxq_disable_fc(port);
}
/* Init all Rx queues for port */
@@ -3018,6 +3125,10 @@ static int mvpp2_setup_rxqs(struct mvpp2_port *port)
if (err)
goto err_cleanup;
}
+
+ if (port->tx_fc)
+ mvpp2_rxq_enable_fc(port);
+
return 0;
err_cleanup:
@@ -4317,6 +4428,8 @@ static int mvpp2_check_ringparam_valid(struct net_device *dev,
if (ring->rx_pending > MVPP2_MAX_RXD_MAX)
new_rx_pending = MVPP2_MAX_RXD_MAX;
+ else if (ring->rx_pending < MSS_THRESHOLD_START)
+ new_rx_pending = MSS_THRESHOLD_START;
else if (!IS_ALIGNED(ring->rx_pending, 16))
new_rx_pending = ALIGN(ring->rx_pending, 16);
@@ -7170,6 +7283,9 @@ static int mvpp2_probe(struct platform_device *pdev)
priv->hw_version = MVPP23;
}
+ /* Init mss lock */
+ spin_lock_init(&priv->mss_spinlock);
+
/* Initialize network controller */
err = mvpp2_init(pdev, priv);
if (err < 0) {
--
1.9.1
From: Stefan Chulski <[email protected]>
The PP2v23 hardware supports a feature allowing to double the
size of BPPI by decreasing number of pools from 16 to 8.
Increasing of BPPI size protect BM drop from BPPI underrun.
Underrun could occurred due to stress on DDR and as result slow buffer
transition from BPPE to BPPI.
New BPPI threshold recommended by spec is:
BPPI low threshold - 640 buffers
BPPI high threshold - 832 buffers
Supported only in PPv23.
Signed-off-by: Stefan Chulski <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 8 +++++
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 35 +++++++++++++++++++-
2 files changed, 42 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 9071ab6..1967493 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -324,6 +324,10 @@
#define MVPP2_BM_HIGH_THRESH_MASK 0x7f0000
#define MVPP2_BM_HIGH_THRESH_VALUE(val) ((val) << \
MVPP2_BM_HIGH_THRESH_OFFS)
+#define MVPP2_BM_BPPI_HIGH_THRESH 0x1E
+#define MVPP2_BM_BPPI_LOW_THRESH 0x1C
+#define MVPP23_BM_BPPI_HIGH_THRESH 0x34
+#define MVPP23_BM_BPPI_LOW_THRESH 0x28
#define MVPP2_BM_INTR_CAUSE_REG(pool) (0x6240 + ((pool) * 4))
#define MVPP2_BM_RELEASED_DELAY_MASK BIT(0)
#define MVPP2_BM_ALLOC_FAILED_MASK BIT(1)
@@ -352,6 +356,10 @@
#define MVPP2_OVERRUN_ETH_DROP 0x7000
#define MVPP2_CLS_ETH_DROP 0x7020
+#define MVPP22_BM_POOL_BASE_ADDR_HIGH_REG 0x6310
+#define MVPP22_BM_POOL_BASE_ADDR_HIGH_MASK 0xff
+#define MVPP23_BM_8POOL_MODE BIT(8)
+
/* Hit counters registers */
#define MVPP2_CTRS_IDX 0x7040
#define MVPP22_CTRS_TX_CTR(port, txq) ((txq) | ((port) << 3) | BIT(7))
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 5d80c5e..e41b173 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -70,6 +70,11 @@ enum mvpp2_bm_pool_log_num {
module_param(queue_mode, int, 0444);
MODULE_PARM_DESC(queue_mode, "Set queue_mode (single=0, multi=1)");
+static int bm_underrun_protect = 1;
+
+module_param(bm_underrun_protect, int, 0444);
+MODULE_PARM_DESC(bm_underrun_protect, "Set BM underrun protect feature (0-1), def=1");
+
/* Utility/helper methods */
void mvpp2_write(struct mvpp2 *priv, u32 offset, u32 data)
@@ -424,6 +429,21 @@ static int mvpp2_bm_pool_create(struct device *dev, struct mvpp2 *priv,
val = mvpp2_read(priv, MVPP2_BM_POOL_CTRL_REG(bm_pool->id));
val |= MVPP2_BM_START_MASK;
+
+ val &= ~MVPP2_BM_LOW_THRESH_MASK;
+ val &= ~MVPP2_BM_HIGH_THRESH_MASK;
+
+ /* Set 8 Pools BPPI threshold if BM underrun protection feature
+ * was enabled
+ */
+ if (priv->hw_version == MVPP23 && bm_underrun_protect) {
+ val |= MVPP2_BM_LOW_THRESH_VALUE(MVPP23_BM_BPPI_LOW_THRESH);
+ val |= MVPP2_BM_HIGH_THRESH_VALUE(MVPP23_BM_BPPI_HIGH_THRESH);
+ } else {
+ val |= MVPP2_BM_LOW_THRESH_VALUE(MVPP2_BM_BPPI_LOW_THRESH);
+ val |= MVPP2_BM_HIGH_THRESH_VALUE(MVPP2_BM_BPPI_HIGH_THRESH);
+ }
+
mvpp2_write(priv, MVPP2_BM_POOL_CTRL_REG(bm_pool->id), val);
bm_pool->size = size;
@@ -592,6 +612,16 @@ static int mvpp2_bm_pools_init(struct device *dev, struct mvpp2 *priv)
return err;
}
+/* Routine enable PPv23 8 pool mode */
+static void mvpp23_bm_set_8pool_mode(struct mvpp2 *priv)
+{
+ int val;
+
+ val = mvpp2_read(priv, MVPP22_BM_POOL_BASE_ADDR_HIGH_REG);
+ val |= MVPP23_BM_8POOL_MODE;
+ mvpp2_write(priv, MVPP22_BM_POOL_BASE_ADDR_HIGH_REG, val);
+}
+
static int mvpp2_bm_init(struct device *dev, struct mvpp2 *priv)
{
enum dma_data_direction dma_dir = DMA_FROM_DEVICE;
@@ -645,6 +675,9 @@ static int mvpp2_bm_init(struct device *dev, struct mvpp2 *priv)
if (!priv->bm_pools)
return -ENOMEM;
+ if (priv->hw_version == MVPP23 && bm_underrun_protect)
+ mvpp23_bm_set_8pool_mode(priv);
+
err = mvpp2_bm_pools_init(dev, priv);
if (err < 0)
return err;
@@ -6491,7 +6524,7 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
val);
}
- if (port->priv->global_tx_fc) {
+ if (port->priv->global_tx_fc && bm_underrun_protect) {
port->tx_fc = tx_pause;
if (tx_pause)
mvpp2_rxq_enable_fc(port);
--
1.9.1
From: Stefan Chulski <[email protected]>
New FIFO flow control feature was added in PPv23.
PPv2 FIFO polled by HW and trigger pause frame if FIFO
fill level is below threshold.
FIFO HW flow control enabled with CM3 RXQ&BM flow
control with ethtool.
Current FIFO thresholds is:
9KB for port with maximum speed 10Gb/s port
4KB for port with maximum speed 5Gb/s port
2KB for port with maximum speed 1Gb/s port
Signed-off-by: Stefan Chulski <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 15 ++++++
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 53 ++++++++++++++++++++
2 files changed, 68 insertions(+)
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 1967493..9947385 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -770,6 +770,18 @@
#define MVPP2_TX_FIFO_THRESHOLD(kb) \
((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
+/* RX FIFO threshold in 1KB granularity */
+#define MVPP23_PORT0_FIFO_TRSH (9 * 1024)
+#define MVPP23_PORT1_FIFO_TRSH (4 * 1024)
+#define MVPP23_PORT2_FIFO_TRSH (2 * 1024)
+
+/* RX Flow Control Registers */
+#define MVPP2_RX_FC_REG(port) (0x150 + 4 * (port))
+#define MVPP2_RX_FC_EN BIT(24)
+#define MVPP2_RX_FC_TRSH_OFFS 16
+#define MVPP2_RX_FC_TRSH_MASK (0xFF << MVPP2_RX_FC_TRSH_OFFS)
+#define MVPP2_RX_FC_TRSH_UNIT 256
+
/* MSS Flow control */
#define MSS_SRAM_SIZE 0x800
#define MSS_FC_COM_REG 0
@@ -1502,6 +1514,8 @@ struct mvpp2_bm_pool {
void mvpp2_dbgfs_cleanup(struct mvpp2 *priv);
+void mvpp23_rx_fifo_fc_en(struct mvpp2 *priv, int port, bool en);
+
#ifdef CONFIG_MVPP2_PTP
int mvpp22_tai_probe(struct device *dev, struct mvpp2 *priv);
void mvpp22_tai_tstamp(struct mvpp2_tai *tai, u32 tstamp,
@@ -1534,4 +1548,5 @@ static inline bool mvpp22_rx_hwtstamping(struct mvpp2_port *port)
{
return IS_ENABLED(CONFIG_MVPP2_PTP) && port->rx_hwtstamp;
}
+
#endif
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index e41b173..5a51697 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -6537,6 +6537,8 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
mvpp2_bm_pool_update_fc(port, port->pool_long, tx_pause);
mvpp2_bm_pool_update_fc(port, port->pool_short, tx_pause);
}
+ if (port->priv->hw_version == MVPP23)
+ mvpp23_rx_fifo_fc_en(port->priv, port->id, tx_pause);
}
mvpp2_port_enable(port);
@@ -7005,6 +7007,55 @@ static void mvpp22_rx_fifo_init(struct mvpp2 *priv)
mvpp2_write(priv, MVPP2_RX_FIFO_INIT_REG, 0x1);
}
+/* Configure Rx FIFO Flow control thresholds */
+static void mvpp23_rx_fifo_fc_set_tresh(struct mvpp2 *priv)
+{
+ int port, val;
+
+ /* Port 0: maximum speed -10Gb/s port
+ * required by spec RX FIFO threshold 9KB
+ * Port 1: maximum speed -5Gb/s port
+ * required by spec RX FIFO threshold 4KB
+ * Port 2: maximum speed -1Gb/s port
+ * required by spec RX FIFO threshold 2KB
+ */
+
+ /* Without loopback port */
+ for (port = 0; port < (MVPP2_MAX_PORTS - 1); port++) {
+ if (port == 0) {
+ val = (MVPP23_PORT0_FIFO_TRSH / MVPP2_RX_FC_TRSH_UNIT)
+ << MVPP2_RX_FC_TRSH_OFFS;
+ val &= MVPP2_RX_FC_TRSH_MASK;
+ mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+ } else if (port == 1) {
+ val = (MVPP23_PORT1_FIFO_TRSH / MVPP2_RX_FC_TRSH_UNIT)
+ << MVPP2_RX_FC_TRSH_OFFS;
+ val &= MVPP2_RX_FC_TRSH_MASK;
+ mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+ } else {
+ val = (MVPP23_PORT2_FIFO_TRSH / MVPP2_RX_FC_TRSH_UNIT)
+ << MVPP2_RX_FC_TRSH_OFFS;
+ val &= MVPP2_RX_FC_TRSH_MASK;
+ mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+ }
+ }
+}
+
+/* Configure Rx FIFO Flow control thresholds */
+void mvpp23_rx_fifo_fc_en(struct mvpp2 *priv, int port, bool en)
+{
+ int val;
+
+ val = mvpp2_read(priv, MVPP2_RX_FC_REG(port));
+
+ if (en)
+ val |= MVPP2_RX_FC_EN;
+ else
+ val &= ~MVPP2_RX_FC_EN;
+
+ mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+}
+
static void mvpp22_tx_fifo_set_hw(struct mvpp2 *priv, int port, int size)
{
int threshold = MVPP2_TX_FIFO_THRESHOLD(size);
@@ -7156,6 +7207,8 @@ static int mvpp2_init(struct platform_device *pdev, struct mvpp2 *priv)
} else {
mvpp22_rx_fifo_init(priv);
mvpp22_tx_fifo_init(priv);
+ if (priv->hw_version == MVPP23)
+ mvpp23_rx_fifo_fc_set_tresh(priv);
}
if (priv->hw_version == MVPP21)
--
1.9.1
From: Stefan Chulski <[email protected]>
This patch enables global flow control in FW and in the phylink validate mask.
Signed-off-by: Stefan Chulski <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 13 ++++++---
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 30 +++++++++++++++++++-
2 files changed, 38 insertions(+), 5 deletions(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index ca84995..e010410 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -763,10 +763,12 @@
((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
/* MSS Flow control */
-#define MSS_SRAM_SIZE 0x800
-#define FC_QUANTA 0xFFFF
-#define FC_CLK_DIVIDER 100
-#define MSS_THRESHOLD_STOP 768
+#define MSS_SRAM_SIZE 0x800
+#define MSS_FC_COM_REG 0
+#define FLOW_CONTROL_ENABLE_BIT BIT(0)
+#define FC_QUANTA 0xFFFF
+#define FC_CLK_DIVIDER 100
+#define MSS_THRESHOLD_STOP 768
/* RX buffer constants */
#define MVPP2_SKB_SHINFO_SIZE \
@@ -1021,6 +1023,9 @@ struct mvpp2 {
/* CM3 SRAM pool */
struct gen_pool *sram_pool;
+
+ /* Global TX Flow Control config */
+ bool global_tx_fc;
};
struct mvpp2_pcpu_stats {
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index a72a390..fec1c81 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -92,6 +92,16 @@ static inline u32 mvpp2_cpu_to_thread(struct mvpp2 *priv, int cpu)
return cpu % priv->nthreads;
}
+static void mvpp2_cm3_write(struct mvpp2 *priv, u32 offset, u32 data)
+{
+ writel(data, priv->cm3_base + offset);
+}
+
+static u32 mvpp2_cm3_read(struct mvpp2 *priv, u32 offset)
+{
+ return readl(priv->cm3_base + offset);
+}
+
static struct page_pool *
mvpp2_create_page_pool(struct device *dev, int num, int len,
enum dma_data_direction dma_dir)
@@ -5951,6 +5961,11 @@ static void mvpp2_phylink_validate(struct phylink_config *config,
phylink_set(mask, Autoneg);
phylink_set_port_modes(mask);
+ if (port->priv->global_tx_fc) {
+ phylink_set(mask, Pause);
+ phylink_set(mask, Asym_Pause);
+ }
+
switch (state->interface) {
case PHY_INTERFACE_MODE_10GBASER:
case PHY_INTERFACE_MODE_XAUI:
@@ -6969,7 +6984,7 @@ static int mvpp2_probe(struct platform_device *pdev)
struct resource *res;
void __iomem *base;
int i, shared;
- int err;
+ int err, val;
priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
@@ -7023,6 +7038,10 @@ static int mvpp2_probe(struct platform_device *pdev)
return err;
else if (err)
dev_warn(&pdev->dev, "Fail to alloc CM3 SRAM\n");
+
+ /* Enable global Flow Control only if handler to SRAM not NULL */
+ if (priv->cm3_base)
+ priv->global_tx_fc = true;
}
if (priv->hw_version != MVPP21 && dev_of_node(&pdev->dev)) {
@@ -7190,6 +7209,15 @@ static int mvpp2_probe(struct platform_device *pdev)
goto err_port_probe;
}
+ /* Enable global flow control. In this stage global
+ * flow control enabled, but still disabled per port.
+ */
+ if (priv->global_tx_fc && priv->hw_version != MVPP21) {
+ val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
+ val |= FLOW_CONTROL_ENABLE_BIT;
+ mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+ }
+
mvpp2_dbgfs_init(priv, pdev->name);
platform_set_drvdata(pdev, priv);
--
1.9.1
From: Stefan Chulski <[email protected]>
This patch add ethtool flow control configuration support.
Tx flow control retrieved correctly by ethtool get function.
FW per port ethtool configuration capability added.
Patch also takes care about mtu change procedure, if PPv2 switch
BM pools during mtu change.
Signed-off-by: Stefan Chulski <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 13 +++
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 98 ++++++++++++++++++++
2 files changed, 111 insertions(+)
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 0f27be0..9071ab6 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -775,6 +775,19 @@
#define MSS_RXQ_TRESH_REG(q, fq) (MSS_RXQ_TRESH_BASE + (((q) + (fq)) \
* MSS_RXQ_TRESH_OFFS))
+#define MSS_BUF_POOL_BASE 0x40
+#define MSS_BUF_POOL_OFFS 4
+#define MSS_BUF_POOL_REG(id) (MSS_BUF_POOL_BASE \
+ + (id) * MSS_BUF_POOL_OFFS)
+
+#define MSS_BUF_POOL_STOP_MASK 0xFFF
+#define MSS_BUF_POOL_START_MASK (0xFFF << MSS_BUF_POOL_START_OFFS)
+#define MSS_BUF_POOL_START_OFFS 12
+#define MSS_BUF_POOL_PORTS_MASK (0xF << MSS_BUF_POOL_PORTS_OFFS)
+#define MSS_BUF_POOL_PORTS_OFFS 24
+#define MSS_BUF_POOL_PORT_OFFS(id) (0x1 << \
+ ((id) + MSS_BUF_POOL_PORTS_OFFS))
+
#define MSS_RXQ_TRESH_START_MASK 0xFFFF
#define MSS_RXQ_TRESH_STOP_MASK (0xFFFF << MSS_RXQ_TRESH_STOP_OFFS)
#define MSS_RXQ_TRESH_STOP_OFFS 16
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 29ba62a..5d80c5e 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -846,6 +846,59 @@ static void mvpp2_rxq_disable_fc(struct mvpp2_port *port)
spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
}
+/* Routine disable/enable flow control for BM pool condition */
+static void mvpp2_bm_pool_update_fc(struct mvpp2_port *port,
+ struct mvpp2_bm_pool *pool,
+ bool en)
+{
+ int val, cm3_state;
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->priv->mss_spinlock, flags);
+
+ /* Remove Flow control enable bit to prevent race between FW and Kernel
+ * If Flow control were enabled, it would be re-enabled.
+ */
+ val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+ cm3_state = (val & FLOW_CONTROL_ENABLE_BIT);
+ val &= ~FLOW_CONTROL_ENABLE_BIT;
+ mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+ /* Check if BM pool should be enabled/disable */
+ if (en) {
+ /* Set BM pool start and stop thresholds per port */
+ val = mvpp2_cm3_read(port->priv, MSS_BUF_POOL_REG(pool->id));
+ val |= MSS_BUF_POOL_PORT_OFFS(port->id);
+ val &= ~MSS_BUF_POOL_START_MASK;
+ val |= (MSS_THRESHOLD_START << MSS_BUF_POOL_START_OFFS);
+ val &= ~MSS_BUF_POOL_STOP_MASK;
+ val |= MSS_THRESHOLD_STOP;
+ mvpp2_cm3_write(port->priv, MSS_BUF_POOL_REG(pool->id), val);
+ } else {
+ /* Remove BM pool from the port */
+ val = mvpp2_cm3_read(port->priv, MSS_BUF_POOL_REG(pool->id));
+ val &= ~MSS_BUF_POOL_PORT_OFFS(port->id);
+
+ /* Zero BM pool start and stop thresholds to disable pool
+ * flow control if pool empty (not used by any port)
+ */
+ if (!pool->buf_num) {
+ val &= ~MSS_BUF_POOL_START_MASK;
+ val &= ~MSS_BUF_POOL_STOP_MASK;
+ }
+
+ mvpp2_cm3_write(port->priv, MSS_BUF_POOL_REG(pool->id), val);
+ }
+
+ /* Notify Firmware that Flow control config space ready for update */
+ val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+ val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+ val |= cm3_state;
+ mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+ spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
+}
+
/* Release buffer to BM */
static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
dma_addr_t buf_dma_addr,
@@ -1176,6 +1229,16 @@ static int mvpp2_bm_update_mtu(struct net_device *dev, int mtu)
new_long_pool = MVPP2_BM_LONG;
if (new_long_pool != port->pool_long->id) {
+ if (port->tx_fc) {
+ if (pkt_size > MVPP2_BM_LONG_PKT_SIZE)
+ mvpp2_bm_pool_update_fc(port,
+ port->pool_short,
+ false);
+ else
+ mvpp2_bm_pool_update_fc(port, port->pool_long,
+ false);
+ }
+
/* Remove port from old short & long pool */
port->pool_long = mvpp2_bm_pool_use(port, port->pool_long->id,
port->pool_long->pkt_size);
@@ -1193,6 +1256,25 @@ static int mvpp2_bm_update_mtu(struct net_device *dev, int mtu)
mvpp2_swf_bm_pool_init(port);
mvpp2_set_hw_csum(port, new_long_pool);
+
+ if (port->tx_fc) {
+ if (pkt_size > MVPP2_BM_LONG_PKT_SIZE)
+ mvpp2_bm_pool_update_fc(port, port->pool_long,
+ true);
+ else
+ mvpp2_bm_pool_update_fc(port, port->pool_short,
+ true);
+ }
+
+ /* Update L4 checksum when jumbo enable/disable on port */
+ if (new_long_pool == MVPP2_BM_JUMBO && port->id != 0) {
+ dev->features &= ~(NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM);
+ dev->hw_features &= ~(NETIF_F_IP_CSUM |
+ NETIF_F_IPV6_CSUM);
+ } else {
+ dev->features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
+ dev->hw_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
+ }
}
out_set:
@@ -6358,6 +6440,7 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
{
struct mvpp2_port *port = mvpp2_phylink_to_port(config);
u32 val;
+ int i;
if (mvpp2_is_xlg(interface)) {
if (!phylink_autoneg_inband(mode)) {
@@ -6408,6 +6491,21 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
val);
}
+ if (port->priv->global_tx_fc) {
+ port->tx_fc = tx_pause;
+ if (tx_pause)
+ mvpp2_rxq_enable_fc(port);
+ else
+ mvpp2_rxq_disable_fc(port);
+ if (port->priv->percpu_pools) {
+ for (i = 0; i < port->nrxqs; i++)
+ mvpp2_bm_pool_update_fc(port, &port->priv->bm_pools[i], tx_pause);
+ } else {
+ mvpp2_bm_pool_update_fc(port, port->pool_long, tx_pause);
+ mvpp2_bm_pool_update_fc(port, port->pool_short, tx_pause);
+ }
+ }
+
mvpp2_port_enable(port);
mvpp2_egress_enable(port);
--
1.9.1
From: Stefan Chulski <[email protected]>
Patch check that TX FC firmware is running in CM3.
If not, global TX FC would be disabled.
Signed-off-by: Stefan Chulski <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 1 +
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 42 ++++++++++++++++----
2 files changed, 36 insertions(+), 7 deletions(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 9947385..25013a4 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -829,6 +829,7 @@
#define MSS_THRESHOLD_STOP 768
#define MSS_THRESHOLD_START 1024
+#define MSS_FC_MAX_TIMEOUT 5000
/* RX buffer constants */
#define MVPP2_SKB_SHINFO_SIZE \
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 5526214..dfc2e71 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -932,6 +932,34 @@ static void mvpp2_bm_pool_update_fc(struct mvpp2_port *port,
spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
}
+static int mvpp2_enable_global_fc(struct mvpp2 *priv)
+{
+ int val, timeout = 0;
+
+ /* Enable global flow control. In this stage global
+ * flow control enabled, but still disabled per port.
+ */
+ val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
+ val |= FLOW_CONTROL_ENABLE_BIT;
+ mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+
+ /* Check if Firmware running and disable FC if not*/
+ val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+ mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+
+ while (timeout < MSS_FC_MAX_TIMEOUT) {
+ val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
+
+ if (!(val & FLOW_CONTROL_UPDATE_COMMAND_BIT))
+ return 0;
+ usleep_range(10, 20);
+ timeout++;
+ }
+
+ priv->global_tx_fc = false;
+ return -EOPNOTSUPP;
+}
+
/* Release buffer to BM */
static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
dma_addr_t buf_dma_addr,
@@ -7281,7 +7309,7 @@ static int mvpp2_probe(struct platform_device *pdev)
struct resource *res;
void __iomem *base;
int i, shared;
- int err, val;
+ int err;
priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
@@ -7509,13 +7537,13 @@ static int mvpp2_probe(struct platform_device *pdev)
goto err_port_probe;
}
- /* Enable global flow control. In this stage global
- * flow control enabled, but still disabled per port.
- */
if (priv->global_tx_fc && priv->hw_version != MVPP21) {
- val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
- val |= FLOW_CONTROL_ENABLE_BIT;
- mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+ err = mvpp2_enable_global_fc(priv);
+ if (err) {
+ dev_warn(&pdev->dev, "CM3 firmware not running, version should be higher than 18.09 ");
+ dev_warn(&pdev->dev, "and chip revision B0\n");
+ dev_warn(&pdev->dev, "Flow control not supported\n");
+ }
}
mvpp2_dbgfs_init(priv, pdev->name);
--
1.9.1
From: Stefan Chulski <[email protected]>
This patch fix GMAC TX flow control autoneg.
Flow control autoneg wrongly were disabled with enabled TX
flow control.
Signed-off-by: Stefan Chulski <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 5a51697..5526214 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -6284,7 +6284,7 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
old_ctrl4 = ctrl4 = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
ctrl0 &= ~MVPP2_GMAC_PORT_TYPE_MASK;
- ctrl2 &= ~(MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK);
+ ctrl2 &= ~(MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK | MVPP2_GMAC_FLOW_CTRL_MASK);
/* Configure port type */
if (phy_interface_mode_is_8023z(state->interface)) {
--
1.9.1
Hi Stefan,
On Sun, Feb 07 2021, [email protected] wrote:
> From: Stefan Chulski <[email protected]>
>
> This patch adds CM3 memory map and CM3 read/write callbacks.
> No functionality changes.
>
> Signed-off-by: Stefan Chulski <[email protected]>
> ---
> drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 7 +++
> drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 63 +++++++++++++++++++-
> 2 files changed, 67 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> index 6bd7e40..aec9179 100644
> --- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> +++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> @@ -748,6 +748,9 @@
> #define MVPP2_TX_FIFO_THRESHOLD(kb) \
> ((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
>
> +/* MSS Flow control */
> +#define MSS_SRAM_SIZE 0x800
> +
> /* RX buffer constants */
> #define MVPP2_SKB_SHINFO_SIZE \
> SKB_DATA_ALIGN(sizeof(struct skb_shared_info))
> @@ -925,6 +928,7 @@ struct mvpp2 {
> /* Shared registers' base addresses */
> void __iomem *lms_base;
> void __iomem *iface_base;
> + void __iomem *cm3_base;
>
> /* On PPv2.2, each "software thread" can access the base
> * register through a separate address space, each 64 KB apart
> @@ -996,6 +1000,9 @@ struct mvpp2 {
>
> /* page_pool allocator */
> struct page_pool *page_pool[MVPP2_PORT_MAX_RXQ];
> +
> + /* CM3 SRAM pool */
> + struct gen_pool *sram_pool;
> };
>
> struct mvpp2_pcpu_stats {
> diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
> index a07cf60..307f9fd 100644
> --- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
> +++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
> @@ -25,6 +25,7 @@
> #include <linux/of_net.h>
> #include <linux/of_address.h>
> #include <linux/of_device.h>
> +#include <linux/genalloc.h>
> #include <linux/phy.h>
> #include <linux/phylink.h>
> #include <linux/phy/phy.h>
> @@ -6846,6 +6847,44 @@ static int mvpp2_init(struct platform_device *pdev, struct mvpp2 *priv)
> return 0;
> }
>
> +static int mvpp2_get_sram(struct platform_device *pdev,
> + struct mvpp2 *priv)
> +{
> + struct device_node *dn = pdev->dev.of_node;
> + static bool defer_once;
> + struct resource *res;
> +
> + if (has_acpi_companion(&pdev->dev)) {
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
> + if (!res) {
> + dev_warn(&pdev->dev, "ACPI is too old, Flow control not supported\n");
> + return 0;
> + }
> + priv->cm3_base = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(priv->cm3_base))
> + return PTR_ERR(priv->cm3_base);
> + } else {
> + priv->sram_pool = of_gen_pool_get(dn, "cm3-mem", 0);
> + if (!priv->sram_pool) {
> + if (!defer_once) {
> + defer_once = true;
> + /* Try defer once */
> + return -EPROBE_DEFER;
> + }
> + dev_warn(&pdev->dev, "DT is too old, Flow control not supported\n");
This warning will show on every DT system with no cm3-mem property, right?
> + return -ENOMEM;
> + }
> + /* cm3_base allocated with offset zero into the SRAM since mapping size
> + * is equal to requested size.
> + */
> + priv->cm3_base = (void __iomem *)gen_pool_alloc(priv->sram_pool,
> + MSS_SRAM_SIZE);
> + if (!priv->cm3_base)
> + return -ENOMEM;
> + }
> + return 0;
> +}
> +
> static int mvpp2_probe(struct platform_device *pdev)
> {
> const struct acpi_device_id *acpi_id;
> @@ -6902,6 +6941,13 @@ static int mvpp2_probe(struct platform_device *pdev)
> priv->iface_base = devm_ioremap_resource(&pdev->dev, res);
> if (IS_ERR(priv->iface_base))
> return PTR_ERR(priv->iface_base);
> +
> + /* Map CM3 SRAM */
> + err = mvpp2_get_sram(pdev, priv);
> + if (err == -EPROBE_DEFER)
> + return err;
> + else if (err)
> + dev_warn(&pdev->dev, "Fail to alloc CM3 SRAM\n");
This one will show as well.
I would not expect that from a patch that makes "no functional change".
baruch
> }
>
> if (priv->hw_version == MVPP22 && dev_of_node(&pdev->dev)) {
> @@ -6947,11 +6993,13 @@ static int mvpp2_probe(struct platform_device *pdev)
>
> if (dev_of_node(&pdev->dev)) {
> priv->pp_clk = devm_clk_get(&pdev->dev, "pp_clk");
> - if (IS_ERR(priv->pp_clk))
> - return PTR_ERR(priv->pp_clk);
> + if (IS_ERR(priv->pp_clk)) {
> + err = PTR_ERR(priv->pp_clk);
> + goto err_cm3;
> + }
> err = clk_prepare_enable(priv->pp_clk);
> if (err < 0)
> - return err;
> + goto err_cm3;
>
> priv->gop_clk = devm_clk_get(&pdev->dev, "gop_clk");
> if (IS_ERR(priv->gop_clk)) {
> @@ -7087,6 +7135,11 @@ static int mvpp2_probe(struct platform_device *pdev)
> clk_disable_unprepare(priv->gop_clk);
> err_pp_clk:
> clk_disable_unprepare(priv->pp_clk);
> +err_cm3:
> + if (priv->sram_pool && priv->cm3_base)
> + gen_pool_free(priv->sram_pool, (unsigned long)priv->cm3_base,
> + MSS_SRAM_SIZE);
> +
> return err;
> }
>
> @@ -7127,6 +7180,10 @@ static int mvpp2_remove(struct platform_device *pdev)
> aggr_txq->descs_dma);
> }
>
> + if (priv->sram_pool && priv->cm3_base)
> + gen_pool_free(priv->sram_pool, (unsigned long)priv->cm3_base,
> + MSS_SRAM_SIZE);
> +
> if (is_acpi_node(port_fwnode))
> return 0;
--
~. .~ Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
- [email protected] - tel: +972.52.368.4656, http://www.tkos.co.il -
> > }
> >
> > +static int mvpp2_get_sram(struct platform_device *pdev,
> > + struct mvpp2 *priv)
> > +{
> > + struct device_node *dn = pdev->dev.of_node;
> > + static bool defer_once;
> > + struct resource *res;
> > +
> > + if (has_acpi_companion(&pdev->dev)) {
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
> > + if (!res) {
> > + dev_warn(&pdev->dev, "ACPI is too old, Flow control
> not supported\n");
> > + return 0;
> > + }
> > + priv->cm3_base = devm_ioremap_resource(&pdev->dev,
> res);
> > + if (IS_ERR(priv->cm3_base))
> > + return PTR_ERR(priv->cm3_base);
> > + } else {
> > + priv->sram_pool = of_gen_pool_get(dn, "cm3-mem", 0);
> > + if (!priv->sram_pool) {
> > + if (!defer_once) {
> > + defer_once = true;
> > + /* Try defer once */
> > + return -EPROBE_DEFER;
> > + }
> > + dev_warn(&pdev->dev, "DT is too old, Flow control
> not
> > +supported\n");
>
> This warning will show on every DT system with no cm3-mem property,
> right?
>
All DT system would has cm3-mem property if " add CM3 SRAM memory to cp11x ethernet device tree " patch applied.
This is also only warning message, without any functional impact.
Regards,
Stefan.
On Sun, Feb 07, 2021 at 10:19:12AM +0200, [email protected] wrote:
> From: Stefan Chulski <[email protected]>
>
> This patch adds CM3 memory map and CM3 read/write callbacks.
> No functionality changes.
>
> Signed-off-by: Stefan Chulski <[email protected]>
> ---
> drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 7 +++
> drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 63 +++++++++++++++++++-
> 2 files changed, 67 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> index 6bd7e40..aec9179 100644
> --- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> +++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> @@ -748,6 +748,9 @@
> #define MVPP2_TX_FIFO_THRESHOLD(kb) \
> ((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
>
> +/* MSS Flow control */
> +#define MSS_SRAM_SIZE 0x800
> +
> /* RX buffer constants */
> #define MVPP2_SKB_SHINFO_SIZE \
> SKB_DATA_ALIGN(sizeof(struct skb_shared_info))
> @@ -925,6 +928,7 @@ struct mvpp2 {
> /* Shared registers' base addresses */
> void __iomem *lms_base;
> void __iomem *iface_base;
> + void __iomem *cm3_base;
>
> /* On PPv2.2, each "software thread" can access the base
> * register through a separate address space, each 64 KB apart
> @@ -996,6 +1000,9 @@ struct mvpp2 {
>
> /* page_pool allocator */
> struct page_pool *page_pool[MVPP2_PORT_MAX_RXQ];
> +
> + /* CM3 SRAM pool */
> + struct gen_pool *sram_pool;
> };
>
> struct mvpp2_pcpu_stats {
> diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
> index a07cf60..307f9fd 100644
> --- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
> +++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
> @@ -25,6 +25,7 @@
> #include <linux/of_net.h>
> #include <linux/of_address.h>
> #include <linux/of_device.h>
> +#include <linux/genalloc.h>
> #include <linux/phy.h>
> #include <linux/phylink.h>
> #include <linux/phy/phy.h>
> @@ -6846,6 +6847,44 @@ static int mvpp2_init(struct platform_device *pdev, struct mvpp2 *priv)
> return 0;
> }
>
> +static int mvpp2_get_sram(struct platform_device *pdev,
> + struct mvpp2 *priv)
> +{
> + struct device_node *dn = pdev->dev.of_node;
> + static bool defer_once;
> + struct resource *res;
> +
> + if (has_acpi_companion(&pdev->dev)) {
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
> + if (!res) {
> + dev_warn(&pdev->dev, "ACPI is too old, Flow control not supported\n");
> + return 0;
> + }
> + priv->cm3_base = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(priv->cm3_base))
> + return PTR_ERR(priv->cm3_base);
> + } else {
> + priv->sram_pool = of_gen_pool_get(dn, "cm3-mem", 0);
> + if (!priv->sram_pool) {
> + if (!defer_once) {
> + defer_once = true;
> + /* Try defer once */
> + return -EPROBE_DEFER;
> + }
> + dev_warn(&pdev->dev, "DT is too old, Flow control not supported\n");
> + return -ENOMEM;
> + }
> + /* cm3_base allocated with offset zero into the SRAM since mapping size
> + * is equal to requested size.
> + */
> + priv->cm3_base = (void __iomem *)gen_pool_alloc(priv->sram_pool,
> + MSS_SRAM_SIZE);
> + if (!priv->cm3_base)
> + return -ENOMEM;
> + }
For v2 i asked:
> I'm wondering if using a pool even makes sense. The ACPI case just
> ioremap() the memory region. Either this memory is dedicated, and
> then there is no need to use a pool, or the memory is shared, and at
> some point the ACPI code is going to run into problems when some
> other driver also wants access.
There was never an answer to this.
Also, the defer_once stuff is odd. You don't see any other driver do
this. The core decides when to give up probing a device. This is
partially an API problem. of_gen_pool_get() gives you no idea why it
failed. Is the property missing, or has the SRAM not probed yet. If
the answer to my question is yes, a pool does make sense, it would be
good to add an of_gen_pool_get_optional() which returns
ERR_PTR(-EPROBE_DEFER) if the property is in DT, but is not yet
available, NULL if the properties does not exist, and a pointer if
everything goes well.
Andrew
> > + priv->sram_pool = of_gen_pool_get(dn, "cm3-mem", 0);
> > + if (!priv->sram_pool) {
> > + if (!defer_once) {
> > + defer_once = true;
> > + /* Try defer once */
> > + return -EPROBE_DEFER;
> > + }
> > + dev_warn(&pdev->dev, "DT is too old, Flow control
> not supported\n");
> > + return -ENOMEM;
> > + }
> > + /* cm3_base allocated with offset zero into the SRAM since
> mapping size
> > + * is equal to requested size.
> > + */
> > + priv->cm3_base = (void __iomem *)gen_pool_alloc(priv-
> >sram_pool,
> > +
> MSS_SRAM_SIZE);
> > + if (!priv->cm3_base)
> > + return -ENOMEM;
> > + }
>
> For v2 i asked:
>
> > I'm wondering if using a pool even makes sense. The ACPI case just
> > ioremap() the memory region. Either this memory is dedicated, and then
> > there is no need to use a pool, or the memory is shared, and at some
> > point the ACPI code is going to run into problems when some other
> > driver also wants access.
>
> There was never an answer to this.
Sorry probably missed this. Currently this memory not shared and I can just ioremap same way as in ACPI case.
In this case I can remove EPROBE_DEFER.
Thanks,
Stefan.