v3:
- pick up Rob's R-b for patches 1 and 2
- reinstate bindings docs license and maintainer
changes with Nikolaus agreement
- took Andy's comments on patch 4 into account
v2:
- keep original bindings license and maintainer/owner (Rob)
- squash bindings patches 2 & 4 (Krzysztof)
v1-resend:
- no change, resending after configuring git to accomodate
for smtp provider limit of 5 emails per batch
- just change cover-letter to mention si-en chip for idol347
The is31fl3190, is31fl3191 and is31fl3193 chips (1 or 3 PWM channels)
cannot be handled the same as is31fl3196 and is31fl3199,
if only because the register map is different.
Also:
- the software shutdown bit is reversed
- and additional field needs to be set to enable all channels
- the led-max-microamp current values and setting are not the same
Datasheets:
https://lumissil.com/assets/pdf/core/IS31FL3190_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3191_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3193_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3196_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3199_DS.pdf
This series:
- converts dt-bindings to dtschema, adding all si-en compatibles
for convenience and consistency, and adding constraints on
supported values for eg. reg address and led-max-microamp
- changes vars, structs and defines to not use 319X suffix
but 3190 for 319{0,1,3} and 3196 for 319{6,9}
- adds fields in chipdef struct for chip-specific values
- only in the last patch, adds is31fl319{0,1,3} specific values
so those chips can work.
Tested on msm8916-alcatel-idol347, which probably has an
si-en,sn3190 or si-en,sn3191 (only one white led indicator).
Vincent Knecht (6):
dt-bindings: leds: Convert is31fl319x to dtschema
dt-bindings: leds: is31fl319x: Document variants specificities
leds: is31fl319x: Add missing si-en compatibles
leds: is31fl319x: Use non-wildcard names for vars, structs and defines
leds: is31fl319x: Move chipset-specific values in chipdef struct
leds: is31fl319x: Add support for is31fl319{0,1,3} chips
.../bindings/leds/issi,is31fl319x.yaml | 193 +++++++++
.../bindings/leds/leds-is31fl319x.txt | 61 ---
drivers/leds/leds-is31fl319x.c | 406 +++++++++++++-----
3 files changed, 488 insertions(+), 172 deletions(-)
create mode 100644 Documentation/devicetree/bindings/leds/issi,is31fl319x.yaml
delete mode 100644 Documentation/devicetree/bindings/leds/leds-is31fl319x.txt
--
2.35.3
Add si-en compatibles for all chip variants.
Signed-off-by: Vincent Knecht <[email protected]>
---
drivers/leds/leds-is31fl319x.c | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/drivers/leds/leds-is31fl319x.c b/drivers/leds/leds-is31fl319x.c
index 4161b9dd7e48..0db5d4988131 100644
--- a/drivers/leds/leds-is31fl319x.c
+++ b/drivers/leds/leds-is31fl319x.c
@@ -102,6 +102,10 @@ static const struct of_device_id of_is31fl319x_match[] = {
{ .compatible = "issi,is31fl3193", .data = &is31fl3193_cdef, },
{ .compatible = "issi,is31fl3196", .data = &is31fl3196_cdef, },
{ .compatible = "issi,is31fl3199", .data = &is31fl3199_cdef, },
+ { .compatible = "si-en,sn3190", .data = &is31fl3190_cdef, },
+ { .compatible = "si-en,sn3191", .data = &is31fl3190_cdef, },
+ { .compatible = "si-en,sn3193", .data = &is31fl3193_cdef, },
+ { .compatible = "si-en,sn3196", .data = &is31fl3196_cdef, },
{ .compatible = "si-en,sn3199", .data = &is31fl3199_cdef, },
{ }
};
@@ -432,6 +436,10 @@ static const struct i2c_device_id is31fl319x_id[] = {
{ "is31fl3193" },
{ "is31fl3196" },
{ "is31fl3199" },
+ { "sn3190" },
+ { "sn3191" },
+ { "sn3193" },
+ { "sn3196" },
{ "sn3199" },
{},
};
--
2.35.3
Convert leds-is31fl319x.txt to dtschema.
Set license to the one recommended by DT project
and set myself as maintainer.
Reviewed-by: Rob Herring <[email protected]>
Signed-off-by: Vincent Knecht <[email protected]>
---
v3:
- changed license back to (GPL-2.0-only OR BSD-2-Clause) and
maintainer to myself, with Nikolaus agreement
---
.../bindings/leds/issi,is31fl319x.yaml | 113 ++++++++++++++++++
.../bindings/leds/leds-is31fl319x.txt | 61 ----------
2 files changed, 113 insertions(+), 61 deletions(-)
create mode 100644 Documentation/devicetree/bindings/leds/issi,is31fl319x.yaml
delete mode 100644 Documentation/devicetree/bindings/leds/leds-is31fl319x.txt
diff --git a/Documentation/devicetree/bindings/leds/issi,is31fl319x.yaml b/Documentation/devicetree/bindings/leds/issi,is31fl319x.yaml
new file mode 100644
index 000000000000..0d684aeeb8cd
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/issi,is31fl319x.yaml
@@ -0,0 +1,113 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/issi,is31fl319x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ISSI LED controllers bindings for IS31FL319{0,1,3,6,9}
+
+maintainers:
+ - Vincent Knecht <[email protected]>
+
+description: |
+ The IS31FL319X are LED controllers with I2C interface.
+ Previously known as Si-En SN319{0,1,3,6,9}.
+
+ For more product information please see the links below:
+ https://lumissil.com/assets/pdf/core/IS31FL3190_DS.pdf
+ https://lumissil.com/assets/pdf/core/IS31FL3191_DS.pdf
+ https://lumissil.com/assets/pdf/core/IS31FL3193_DS.pdf
+ https://lumissil.com/assets/pdf/core/IS31FL3196_DS.pdf
+ https://lumissil.com/assets/pdf/core/IS31FL3199_DS.pdf
+
+properties:
+ compatible:
+ enum:
+ - issi,is31fl3190
+ - issi,is31fl3191
+ - issi,is31fl3193
+ - issi,is31fl3196
+ - issi,is31fl3199
+ - si-en,sn3199
+
+ reg:
+ maxItems: 1
+
+ shutdown-gpios:
+ maxItems: 1
+ description: GPIO attached to the SDB pin.
+
+ audio-gain-db:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 0
+ description: Audio gain selection for external analog modulation input.
+ enum: [0, 3, 6, 9, 12, 15, 18, 21]
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
+
+patternProperties:
+ "^led@[1-9]$":
+ type: object
+ $ref: common.yaml#
+
+ properties:
+ reg:
+ description: Index of the LED.
+ minimum: 1
+ maximum: 9
+
+ led-max-microamp:
+ default: 20000
+ enum: [5000, 10000, 15000, 20000, 25000, 30000, 35000, 40000]
+ description:
+ Note that a driver will take the lowest of all LED limits
+ since the chip has a single global setting. The lowest value
+ will be chosen due to the PWM specificity, where lower
+ brightness is achieved by reducing the duty-cycle of pulses
+ and not the current, which will always have its peak value
+ equal to led-max-microamp.
+
+required:
+ - compatible
+ - reg
+ - "#address-cells"
+ - "#size-cells"
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/leds/common.h>
+
+ i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led-controller@65 {
+ compatible = "issi,is31fl3196";
+ reg = <0x65>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ shutdown-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+
+ led@1 {
+ reg = <1>;
+ label = "red:aux";
+ led-max-microamp = <10000>;
+ };
+
+ led@5 {
+ reg = <5>;
+ label = "green:power";
+ linux,default-trigger = "default-on";
+ };
+ };
+ };
+...
+
diff --git a/Documentation/devicetree/bindings/leds/leds-is31fl319x.txt b/Documentation/devicetree/bindings/leds/leds-is31fl319x.txt
deleted file mode 100644
index 676d43ec8169..000000000000
--- a/Documentation/devicetree/bindings/leds/leds-is31fl319x.txt
+++ /dev/null
@@ -1,61 +0,0 @@
-LEDs connected to is31fl319x LED controller chip
-
-Required properties:
-- compatible : Should be any of
- "issi,is31fl3190"
- "issi,is31fl3191"
- "issi,is31fl3193"
- "issi,is31fl3196"
- "issi,is31fl3199"
- "si-en,sn3199".
-- #address-cells: Must be 1.
-- #size-cells: Must be 0.
-- reg: 0x64, 0x65, 0x66, or 0x67.
-
-Optional properties:
-- audio-gain-db : audio gain selection for external analog modulation input.
- Valid values: 0 - 21, step by 3 (rounded down)
- Default: 0
-- shutdown-gpios : Specifier of the GPIO connected to SDB pin of the chip.
-
-Each led is represented as a sub-node of the issi,is31fl319x device.
-There can be less leds subnodes than the chip can support but not more.
-
-Required led sub-node properties:
-- reg : number of LED line
- Valid values: 1 - number of leds supported by the chip variant.
-
-Optional led sub-node properties:
-- label : see Documentation/devicetree/bindings/leds/common.txt.
-- linux,default-trigger :
- see Documentation/devicetree/bindings/leds/common.txt.
-- led-max-microamp : (optional)
- Valid values: 5000 - 40000, step by 5000 (rounded down)
- Default: 20000 (20 mA)
- Note: a driver will take the lowest of all led limits since the
- chip has a single global setting. The lowest value will be chosen
- due to the PWM specificity, where lower brightness is achieved
- by reducing the dury-cycle of pulses and not the current, which
- will always have its peak value equal to led-max-microamp.
-
-Examples:
-
-fancy_leds: leds@65 {
- compatible = "issi,is31fl3196";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x65>;
- shutdown-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
-
- red_aux: led@1 {
- label = "red:aux";
- reg = <1>;
- led-max-microamp = <10000>;
- };
-
- green_power: led@5 {
- label = "green:power";
- reg = <5>;
- linux,default-trigger = "default-on";
- };
-};
--
2.35.3
Set specific chipset structs values for is31fl319{0,1,3}
so that those chips can actually work.
Datasheets:
https://lumissil.com/assets/pdf/core/IS31FL3190_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3191_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3193_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3196_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3199_DS.pdf
Signed-off-by: Vincent Knecht <[email protected]>
---
drivers/leds/leds-is31fl319x.c | 164 ++++++++++++++++++++++++++++++---
1 file changed, 150 insertions(+), 14 deletions(-)
diff --git a/drivers/leds/leds-is31fl319x.c b/drivers/leds/leds-is31fl319x.c
index 0bccee6da5bf..911edcf973c1 100644
--- a/drivers/leds/leds-is31fl319x.c
+++ b/drivers/leds/leds-is31fl319x.c
@@ -21,6 +21,31 @@
/* register numbers */
#define IS31FL319X_SHUTDOWN 0x00
+
+/* registers for 3190, 3191 and 3193 */
+#define IS31FL3190_BREATHING 0x01
+#define IS31FL3190_LEDMODE 0x02
+#define IS31FL3190_CURRENT 0x03
+#define IS31FL3190_PWM(channel) (0x04 + channel)
+#define IS31FL3190_DATA_UPDATE 0x07
+#define IS31FL3190_T0(channel) (0x0a + channel)
+#define IS31FL3190_T1T2(channel) (0x10 + channel)
+#define IS31FL3190_T3T4(channel) (0x16 + channel)
+#define IS31FL3190_TIME_UPDATE 0x1c
+#define IS31FL3190_LEDCONTROL 0x1d
+#define IS31FL3190_RESET 0x2f
+
+#define IS31FL3190_CURRENT_uA_MIN 5000
+#define IS31FL3190_CURRENT_uA_DEFAULT 42000
+#define IS31FL3190_CURRENT_uA_MAX 42000
+#define IS31FL3190_CURRENT_MASK GENMASK(4, 2)
+#define IS31FL3190_CURRENT_5_mA 0x02
+#define IS31FL3190_CURRENT_10_mA 0x01
+#define IS31FL3190_CURRENT_17dot5_mA 0x04
+#define IS31FL3190_CURRENT_30_mA 0x03
+#define IS31FL3190_CURRENT_42_mA 0x00
+
+/* registers for 3196 and 3199 */
#define IS31FL3196_CTRL1 0x01
#define IS31FL3196_CTRL2 0x02
#define IS31FL3196_CONFIG1 0x03
@@ -92,6 +117,37 @@ static bool is31fl319x_readable_reg(struct device *dev, unsigned int reg)
return false;
}
+static bool is31fl3190_volatile_reg(struct device *dev, unsigned int reg)
+{ /* volatile registers are not cached */
+ switch (reg) {
+ case IS31FL3190_DATA_UPDATE:
+ case IS31FL3190_TIME_UPDATE:
+ case IS31FL3190_RESET:
+ return true; /* always write-through */
+ default:
+ return false;
+ }
+}
+
+static const struct reg_default is31fl3190_reg_defaults[] = {
+ { IS31FL3190_LEDMODE, 0x00},
+ { IS31FL3190_CURRENT, 0x00},
+ { IS31FL3190_PWM(0), 0x00},
+ { IS31FL3190_PWM(1), 0x00},
+ { IS31FL3190_PWM(2), 0x00},
+};
+
+static struct regmap_config is31fl3190_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = IS31FL3190_RESET,
+ .cache_type = REGCACHE_FLAT,
+ .readable_reg = is31fl319x_readable_reg,
+ .volatile_reg = is31fl3190_volatile_reg,
+ .reg_defaults = is31fl3190_reg_defaults,
+ .num_reg_defaults = ARRAY_SIZE(is31fl3190_reg_defaults),
+};
+
static bool is31fl3196_volatile_reg(struct device *dev, unsigned int reg)
{ /* volatile registers are not cached */
switch (reg) {
@@ -129,6 +185,63 @@ static struct regmap_config is31fl3196_regmap_config = {
.num_reg_defaults = ARRAY_SIZE(is31fl3196_reg_defaults),
};
+static int is31fl3190_brightness_set(struct led_classdev *cdev,
+ enum led_brightness brightness)
+{
+ struct is31fl319x_led *led = container_of(cdev, struct is31fl319x_led,
+ cdev);
+ struct is31fl319x_chip *is31 = led->chip;
+ int chan = led - is31->leds;
+ int ret;
+ int i;
+ u8 ctrl = 0;
+
+ dev_dbg(&is31->client->dev, "%s %d: %d\n", __func__, chan, brightness);
+
+ mutex_lock(&is31->lock);
+
+ /* update PWM register */
+ ret = regmap_write(is31->regmap, IS31FL3190_PWM(chan), brightness);
+ if (ret < 0)
+ goto out;
+
+ /* read current brightness of all PWM channels */
+ for (i = 0; i < is31->cdef->num_leds; i++) {
+ unsigned int pwm_value;
+ bool on;
+
+ /*
+ * since neither cdev nor the chip can provide
+ * the current setting, we read from the regmap cache
+ */
+
+ ret = regmap_read(is31->regmap, IS31FL3190_PWM(i), &pwm_value);
+ dev_dbg(&is31->client->dev, "%s read %d: ret=%d: %d\n",
+ __func__, i, ret, pwm_value);
+ on = ret >= 0 && pwm_value > LED_OFF;
+
+ ctrl |= on << i;
+ }
+
+ if (ctrl > 0) {
+ dev_dbg(&is31->client->dev, "power up %02x\n", ctrl);
+ regmap_write(is31->regmap, IS31FL3190_LEDCONTROL, ctrl);
+ /* update PWMs */
+ regmap_write(is31->regmap, IS31FL3190_DATA_UPDATE, 0x00);
+ /* enable chip from shut down and enable all channels */
+ ret = regmap_write(is31->regmap, IS31FL319X_SHUTDOWN, 0x20);
+ } else {
+ dev_dbg(&is31->client->dev, "power down\n");
+ /* shut down (no need to clear LEDCONTROL) */
+ ret = regmap_write(is31->regmap, IS31FL319X_SHUTDOWN, 0x01);
+ }
+
+out:
+ mutex_unlock(&is31->lock);
+
+ return ret;
+}
+
static int is31fl3196_brightness_set(struct led_classdev *cdev,
enum led_brightness brightness)
{
@@ -195,24 +308,24 @@ static int is31fl3196_brightness_set(struct led_classdev *cdev,
static const struct is31fl319x_chipdef is31fl3190_cdef = {
.num_leds = 1,
- .reset_reg = IS31FL3196_RESET,
- .is31fl319x_regmap_config = &is31fl3196_regmap_config,
- .brightness_set = is31fl3196_brightness_set,
- .current_default = IS31FL3196_CURRENT_uA_DEFAULT,
- .current_min = IS31FL3196_CURRENT_uA_MIN,
- .current_max = IS31FL3196_CURRENT_uA_MAX,
- .is_3196or3199 = true,
+ .reset_reg = IS31FL3190_RESET,
+ .is31fl319x_regmap_config = &is31fl3190_regmap_config,
+ .brightness_set = is31fl3190_brightness_set,
+ .current_default = IS31FL3190_CURRENT_uA_DEFAULT,
+ .current_min = IS31FL3190_CURRENT_uA_MIN,
+ .current_max = IS31FL3190_CURRENT_uA_MAX,
+ .is_3196or3199 = false,
};
static const struct is31fl319x_chipdef is31fl3193_cdef = {
.num_leds = 3,
- .reset_reg = IS31FL3196_RESET,
- .is31fl319x_regmap_config = &is31fl3196_regmap_config,
- .brightness_set = is31fl3196_brightness_set,
- .current_default = IS31FL3196_CURRENT_uA_DEFAULT,
- .current_min = IS31FL3196_CURRENT_uA_MIN,
- .current_max = IS31FL3196_CURRENT_uA_MAX,
- .is_3196or3199 = true,
+ .reset_reg = IS31FL3190_RESET,
+ .is31fl319x_regmap_config = &is31fl3190_regmap_config,
+ .brightness_set = is31fl3190_brightness_set,
+ .current_default = IS31FL3190_CURRENT_uA_DEFAULT,
+ .current_min = IS31FL3190_CURRENT_uA_MIN,
+ .current_max = IS31FL3190_CURRENT_uA_MAX,
+ .is_3196or3199 = false,
};
static const struct is31fl319x_chipdef is31fl3196_cdef = {
@@ -360,6 +473,26 @@ static int is31fl319x_parse_dt(struct device *dev,
return ret;
}
+static inline int is31fl3190_microamp_to_cs(struct device *dev, u32 microamp)
+{
+ switch (microamp) {
+ case 5000:
+ return IS31FL3190_CURRENT_5_mA;
+ case 10000:
+ return IS31FL3190_CURRENT_10_mA;
+ case 17500:
+ return IS31FL3190_CURRENT_17dot5_mA;
+ case 30000:
+ return IS31FL3190_CURRENT_30_mA;
+ case 42000:
+ return IS31FL3190_CURRENT_42_mA;
+ default:
+ dev_warn(dev, "Unsupported current value: %d, using 5000 µA!\n", microamp);
+ }
+
+ return IS31FL3190_CURRENT_5_mA;
+}
+
static inline int is31fl3196_microamp_to_cs(struct device *dev, u32 microamp)
{ /* round down to nearest supported value (range check done by caller) */
u32 step = microamp / IS31FL3196_CURRENT_uA_STEP;
@@ -436,6 +569,9 @@ static int is31fl319x_probe(struct i2c_client *client,
regmap_write(is31->regmap, IS31FL3196_CONFIG2,
is31fl3196_microamp_to_cs(dev, aggregated_led_microamp) |
is31fl3196_db_to_gain(is31->audio_gain_db));
+ else
+ regmap_update_bits(is31->regmap, IS31FL3190_CURRENT, IS31FL3190_CURRENT_MASK,
+ is31fl3190_microamp_to_cs(dev, aggregated_led_microamp));
for (i = 0; i < is31->cdef->num_leds; i++) {
struct is31fl319x_led *led = &is31->leds[i];
--
2.35.3
In order to add real support for is31fl3190, is31fl3191 and is31fl3193,
rename variant-dependent elements to not use 319X where needed.
3190 suffix is used for is31fl3190, is31fl3191 and is31fl3193 circuits.
3196 suffix is used for is31fl3196 and is31fl3199.
Those two groups have different register maps, current settings and even
a different interpretation of the software shutdown bit:
https://lumissil.com/assets/pdf/core/IS31FL3190_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3191_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3193_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3196_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3199_DS.pdf
Rename variables, structures and defines in preparation of the splitting.
No functional nor behaviour change.
Signed-off-by: Vincent Knecht <[email protected]>
---
v3:
- rename IS31FL3196_BREATH_MASK to IS31FL3196_BREATH_MARK
since it refers to "breathing mark" function, not to a bitmask
- use GENMASK for IS31FL3196_CONFIG2_CS_MASK (Andy)
- get rid of u32 castings in defines (Andy)
- add _uA_ in IS31FL3196_CURRENT defines to denote the unit (Andy)
- fix stuctures typo in commit message (Andy)
---
drivers/leds/leds-is31fl319x.c | 142 ++++++++++++++++-----------------
1 file changed, 71 insertions(+), 71 deletions(-)
diff --git a/drivers/leds/leds-is31fl319x.c b/drivers/leds/leds-is31fl319x.c
index 0db5d4988131..e6fe0a8bc8d5 100644
--- a/drivers/leds/leds-is31fl319x.c
+++ b/drivers/leds/leds-is31fl319x.c
@@ -21,39 +21,39 @@
/* register numbers */
#define IS31FL319X_SHUTDOWN 0x00
-#define IS31FL319X_CTRL1 0x01
-#define IS31FL319X_CTRL2 0x02
-#define IS31FL319X_CONFIG1 0x03
-#define IS31FL319X_CONFIG2 0x04
-#define IS31FL319X_RAMP_MODE 0x05
-#define IS31FL319X_BREATH_MASK 0x06
-#define IS31FL319X_PWM(channel) (0x07 + channel)
-#define IS31FL319X_DATA_UPDATE 0x10
-#define IS31FL319X_T0(channel) (0x11 + channel)
-#define IS31FL319X_T123_1 0x1a
-#define IS31FL319X_T123_2 0x1b
-#define IS31FL319X_T123_3 0x1c
-#define IS31FL319X_T4(channel) (0x1d + channel)
-#define IS31FL319X_TIME_UPDATE 0x26
-#define IS31FL319X_RESET 0xff
-
-#define IS31FL319X_REG_CNT (IS31FL319X_RESET + 1)
+#define IS31FL3196_CTRL1 0x01
+#define IS31FL3196_CTRL2 0x02
+#define IS31FL3196_CONFIG1 0x03
+#define IS31FL3196_CONFIG2 0x04
+#define IS31FL3196_RAMP_MODE 0x05
+#define IS31FL3196_BREATH_MARK 0x06
+#define IS31FL3196_PWM(channel) (0x07 + channel)
+#define IS31FL3196_DATA_UPDATE 0x10
+#define IS31FL3196_T0(channel) (0x11 + channel)
+#define IS31FL3196_T123_1 0x1a
+#define IS31FL3196_T123_2 0x1b
+#define IS31FL3196_T123_3 0x1c
+#define IS31FL3196_T4(channel) (0x1d + channel)
+#define IS31FL3196_TIME_UPDATE 0x26
+#define IS31FL3196_RESET 0xff
+
+#define IS31FL3196_REG_CNT (IS31FL3196_RESET + 1)
#define IS31FL319X_MAX_LEDS 9
/* CS (Current Setting) in CONFIG2 register */
-#define IS31FL319X_CONFIG2_CS_SHIFT 4
-#define IS31FL319X_CONFIG2_CS_MASK 0x7
-#define IS31FL319X_CONFIG2_CS_STEP_REF 12
+#define IS31FL3196_CONFIG2_CS_SHIFT 4
+#define IS31FL3196_CONFIG2_CS_MASK GENMASK(2, 0)
+#define IS31FL3196_CONFIG2_CS_STEP_REF 12
-#define IS31FL319X_CURRENT_MIN ((u32)5000)
-#define IS31FL319X_CURRENT_MAX ((u32)40000)
-#define IS31FL319X_CURRENT_STEP ((u32)5000)
-#define IS31FL319X_CURRENT_DEFAULT ((u32)20000)
+#define IS31FL3196_CURRENT_uA_MIN 5000
+#define IS31FL3196_CURRENT_uA_MAX 40000
+#define IS31FL3196_CURRENT_uA_STEP 5000
+#define IS31FL3196_CURRENT_uA_DEFAULT 20000
/* Audio gain in CONFIG2 register */
-#define IS31FL319X_AUDIO_GAIN_DB_MAX ((u32)21)
-#define IS31FL319X_AUDIO_GAIN_DB_STEP ((u32)3)
+#define IS31FL3196_AUDIO_GAIN_DB_MAX 21
+#define IS31FL3196_AUDIO_GAIN_DB_STEP 3
/*
* regmap is used as a cache of chip's register space,
@@ -111,7 +111,7 @@ static const struct of_device_id of_is31fl319x_match[] = {
};
MODULE_DEVICE_TABLE(of, of_is31fl319x_match);
-static int is31fl319x_brightness_set(struct led_classdev *cdev,
+static int is31fl3196_brightness_set(struct led_classdev *cdev,
enum led_brightness brightness)
{
struct is31fl319x_led *led = container_of(cdev, struct is31fl319x_led,
@@ -127,7 +127,7 @@ static int is31fl319x_brightness_set(struct led_classdev *cdev,
mutex_lock(&is31->lock);
/* update PWM register */
- ret = regmap_write(is31->regmap, IS31FL319X_PWM(chan), brightness);
+ ret = regmap_write(is31->regmap, IS31FL3196_PWM(chan), brightness);
if (ret < 0)
goto out;
@@ -141,7 +141,7 @@ static int is31fl319x_brightness_set(struct led_classdev *cdev,
* the current setting, we read from the regmap cache
*/
- ret = regmap_read(is31->regmap, IS31FL319X_PWM(i), &pwm_value);
+ ret = regmap_read(is31->regmap, IS31FL3196_PWM(i), &pwm_value);
dev_dbg(&is31->client->dev, "%s read %d: ret=%d: %d\n",
__func__, i, ret, pwm_value);
on = ret >= 0 && pwm_value > LED_OFF;
@@ -157,10 +157,10 @@ static int is31fl319x_brightness_set(struct led_classdev *cdev,
if (ctrl1 > 0 || ctrl2 > 0) {
dev_dbg(&is31->client->dev, "power up %02x %02x\n",
ctrl1, ctrl2);
- regmap_write(is31->regmap, IS31FL319X_CTRL1, ctrl1);
- regmap_write(is31->regmap, IS31FL319X_CTRL2, ctrl2);
+ regmap_write(is31->regmap, IS31FL3196_CTRL1, ctrl1);
+ regmap_write(is31->regmap, IS31FL3196_CTRL2, ctrl2);
/* update PWMs */
- regmap_write(is31->regmap, IS31FL319X_DATA_UPDATE, 0x00);
+ regmap_write(is31->regmap, IS31FL3196_DATA_UPDATE, 0x00);
/* enable chip from shut down */
ret = regmap_write(is31->regmap, IS31FL319X_SHUTDOWN, 0x01);
} else {
@@ -190,14 +190,14 @@ static int is31fl319x_parse_child_dt(const struct device *dev,
if (ret < 0 && ret != -EINVAL) /* is optional */
return ret;
- led->max_microamp = IS31FL319X_CURRENT_DEFAULT;
+ led->max_microamp = IS31FL3196_CURRENT_uA_DEFAULT;
ret = of_property_read_u32(child, "led-max-microamp",
&led->max_microamp);
if (!ret) {
- if (led->max_microamp < IS31FL319X_CURRENT_MIN)
+ if (led->max_microamp < IS31FL3196_CURRENT_uA_MIN)
return -EINVAL; /* not supported */
led->max_microamp = min(led->max_microamp,
- IS31FL319X_CURRENT_MAX);
+ IS31FL3196_CURRENT_uA_MAX);
}
return 0;
@@ -271,7 +271,7 @@ static int is31fl319x_parse_dt(struct device *dev,
ret = of_property_read_u32(np, "audio-gain-db", &is31->audio_gain_db);
if (!ret)
is31->audio_gain_db = min(is31->audio_gain_db,
- IS31FL319X_AUDIO_GAIN_DB_MAX);
+ IS31FL3196_AUDIO_GAIN_DB_MAX);
return 0;
@@ -285,55 +285,55 @@ static bool is31fl319x_readable_reg(struct device *dev, unsigned int reg)
return false;
}
-static bool is31fl319x_volatile_reg(struct device *dev, unsigned int reg)
+static bool is31fl3196_volatile_reg(struct device *dev, unsigned int reg)
{ /* volatile registers are not cached */
switch (reg) {
- case IS31FL319X_DATA_UPDATE:
- case IS31FL319X_TIME_UPDATE:
- case IS31FL319X_RESET:
+ case IS31FL3196_DATA_UPDATE:
+ case IS31FL3196_TIME_UPDATE:
+ case IS31FL3196_RESET:
return true; /* always write-through */
default:
return false;
}
}
-static const struct reg_default is31fl319x_reg_defaults[] = {
- { IS31FL319X_CONFIG1, 0x00},
- { IS31FL319X_CONFIG2, 0x00},
- { IS31FL319X_PWM(0), 0x00},
- { IS31FL319X_PWM(1), 0x00},
- { IS31FL319X_PWM(2), 0x00},
- { IS31FL319X_PWM(3), 0x00},
- { IS31FL319X_PWM(4), 0x00},
- { IS31FL319X_PWM(5), 0x00},
- { IS31FL319X_PWM(6), 0x00},
- { IS31FL319X_PWM(7), 0x00},
- { IS31FL319X_PWM(8), 0x00},
+static const struct reg_default is31fl3196_reg_defaults[] = {
+ { IS31FL3196_CONFIG1, 0x00},
+ { IS31FL3196_CONFIG2, 0x00},
+ { IS31FL3196_PWM(0), 0x00},
+ { IS31FL3196_PWM(1), 0x00},
+ { IS31FL3196_PWM(2), 0x00},
+ { IS31FL3196_PWM(3), 0x00},
+ { IS31FL3196_PWM(4), 0x00},
+ { IS31FL3196_PWM(5), 0x00},
+ { IS31FL3196_PWM(6), 0x00},
+ { IS31FL3196_PWM(7), 0x00},
+ { IS31FL3196_PWM(8), 0x00},
};
-static struct regmap_config regmap_config = {
+static struct regmap_config is31fl3196_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
- .max_register = IS31FL319X_REG_CNT,
+ .max_register = IS31FL3196_REG_CNT,
.cache_type = REGCACHE_FLAT,
.readable_reg = is31fl319x_readable_reg,
- .volatile_reg = is31fl319x_volatile_reg,
- .reg_defaults = is31fl319x_reg_defaults,
- .num_reg_defaults = ARRAY_SIZE(is31fl319x_reg_defaults),
+ .volatile_reg = is31fl3196_volatile_reg,
+ .reg_defaults = is31fl3196_reg_defaults,
+ .num_reg_defaults = ARRAY_SIZE(is31fl3196_reg_defaults),
};
-static inline int is31fl319x_microamp_to_cs(struct device *dev, u32 microamp)
+static inline int is31fl3196_microamp_to_cs(struct device *dev, u32 microamp)
{ /* round down to nearest supported value (range check done by caller) */
- u32 step = microamp / IS31FL319X_CURRENT_STEP;
+ u32 step = microamp / IS31FL3196_CURRENT_uA_STEP;
- return ((IS31FL319X_CONFIG2_CS_STEP_REF - step) &
- IS31FL319X_CONFIG2_CS_MASK) <<
- IS31FL319X_CONFIG2_CS_SHIFT; /* CS encoding */
+ return ((IS31FL3196_CONFIG2_CS_STEP_REF - step) &
+ IS31FL3196_CONFIG2_CS_MASK) <<
+ IS31FL3196_CONFIG2_CS_SHIFT; /* CS encoding */
}
-static inline int is31fl319x_db_to_gain(u32 dezibel)
+static inline int is31fl3196_db_to_gain(u32 dezibel)
{ /* round down to nearest supported value (range check done by caller) */
- return dezibel / IS31FL319X_AUDIO_GAIN_DB_STEP;
+ return dezibel / IS31FL3196_AUDIO_GAIN_DB_STEP;
}
static int is31fl319x_probe(struct i2c_client *client,
@@ -343,7 +343,7 @@ static int is31fl319x_probe(struct i2c_client *client,
struct device *dev = &client->dev;
int err;
int i = 0;
- u32 aggregated_led_microamp = IS31FL319X_CURRENT_MAX;
+ u32 aggregated_led_microamp = IS31FL3196_CURRENT_uA_MAX;
if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C))
return -EIO;
@@ -365,7 +365,7 @@ static int is31fl319x_probe(struct i2c_client *client,
}
is31->client = client;
- is31->regmap = devm_regmap_init_i2c(client, ®map_config);
+ is31->regmap = devm_regmap_init_i2c(client, &is31fl3196_regmap_config);
if (IS_ERR(is31->regmap)) {
dev_err(&client->dev, "failed to allocate register map\n");
err = PTR_ERR(is31->regmap);
@@ -375,7 +375,7 @@ static int is31fl319x_probe(struct i2c_client *client,
i2c_set_clientdata(client, is31);
/* check for write-reply from chip (we can't read any registers) */
- err = regmap_write(is31->regmap, IS31FL319X_RESET, 0x00);
+ err = regmap_write(is31->regmap, IS31FL3196_RESET, 0x00);
if (err < 0) {
dev_err(&client->dev, "no response from chip write: err = %d\n",
err);
@@ -393,9 +393,9 @@ static int is31fl319x_probe(struct i2c_client *client,
is31->leds[i].max_microamp < aggregated_led_microamp)
aggregated_led_microamp = is31->leds[i].max_microamp;
- regmap_write(is31->regmap, IS31FL319X_CONFIG2,
- is31fl319x_microamp_to_cs(dev, aggregated_led_microamp) |
- is31fl319x_db_to_gain(is31->audio_gain_db));
+ regmap_write(is31->regmap, IS31FL3196_CONFIG2,
+ is31fl3196_microamp_to_cs(dev, aggregated_led_microamp) |
+ is31fl3196_db_to_gain(is31->audio_gain_db));
for (i = 0; i < is31->cdef->num_leds; i++) {
struct is31fl319x_led *led = &is31->leds[i];
@@ -404,7 +404,7 @@ static int is31fl319x_probe(struct i2c_client *client,
continue;
led->chip = is31;
- led->cdev.brightness_set_blocking = is31fl319x_brightness_set;
+ led->cdev.brightness_set_blocking = is31fl3196_brightness_set;
err = devm_led_classdev_register(&client->dev, &led->cdev);
if (err < 0)
--
2.35.3
Allow setting chips' specifics in chipdef struct by adding fields for:
- the reset register address
- a pointer to a regmap_config struct
- a pointer to a brightness_set function
- current default, min and max values
- a boolean to distinguish 319{0,1,3} and 319{6,9} chips
and use those fields in places where distinction has to be made.
The fields for 319{0,1,3} still point to 319{6,9} values.
No functional change.
Signed-off-by: Vincent Knecht <[email protected]>
---
drivers/leds/leds-is31fl319x.c | 206 ++++++++++++++++++++-------------
1 file changed, 123 insertions(+), 83 deletions(-)
diff --git a/drivers/leds/leds-is31fl319x.c b/drivers/leds/leds-is31fl319x.c
index e6fe0a8bc8d5..0bccee6da5bf 100644
--- a/drivers/leds/leds-is31fl319x.c
+++ b/drivers/leds/leds-is31fl319x.c
@@ -78,38 +78,56 @@ struct is31fl319x_chip {
struct is31fl319x_chipdef {
int num_leds;
+ u8 reset_reg;
+ const struct regmap_config *is31fl319x_regmap_config;
+ int (*brightness_set)(struct led_classdev *cdev, enum led_brightness brightness);
+ u32 current_default;
+ u32 current_min;
+ u32 current_max;
+ bool is_3196or3199;
};
-static const struct is31fl319x_chipdef is31fl3190_cdef = {
- .num_leds = 1,
-};
-
-static const struct is31fl319x_chipdef is31fl3193_cdef = {
- .num_leds = 3,
-};
+static bool is31fl319x_readable_reg(struct device *dev, unsigned int reg)
+{ /* we have no readable registers */
+ return false;
+}
-static const struct is31fl319x_chipdef is31fl3196_cdef = {
- .num_leds = 6,
-};
+static bool is31fl3196_volatile_reg(struct device *dev, unsigned int reg)
+{ /* volatile registers are not cached */
+ switch (reg) {
+ case IS31FL3196_DATA_UPDATE:
+ case IS31FL3196_TIME_UPDATE:
+ case IS31FL3196_RESET:
+ return true; /* always write-through */
+ default:
+ return false;
+ }
+}
-static const struct is31fl319x_chipdef is31fl3199_cdef = {
- .num_leds = 9,
+static const struct reg_default is31fl3196_reg_defaults[] = {
+ { IS31FL3196_CONFIG1, 0x00},
+ { IS31FL3196_CONFIG2, 0x00},
+ { IS31FL3196_PWM(0), 0x00},
+ { IS31FL3196_PWM(1), 0x00},
+ { IS31FL3196_PWM(2), 0x00},
+ { IS31FL3196_PWM(3), 0x00},
+ { IS31FL3196_PWM(4), 0x00},
+ { IS31FL3196_PWM(5), 0x00},
+ { IS31FL3196_PWM(6), 0x00},
+ { IS31FL3196_PWM(7), 0x00},
+ { IS31FL3196_PWM(8), 0x00},
};
-static const struct of_device_id of_is31fl319x_match[] = {
- { .compatible = "issi,is31fl3190", .data = &is31fl3190_cdef, },
- { .compatible = "issi,is31fl3191", .data = &is31fl3190_cdef, },
- { .compatible = "issi,is31fl3193", .data = &is31fl3193_cdef, },
- { .compatible = "issi,is31fl3196", .data = &is31fl3196_cdef, },
- { .compatible = "issi,is31fl3199", .data = &is31fl3199_cdef, },
- { .compatible = "si-en,sn3190", .data = &is31fl3190_cdef, },
- { .compatible = "si-en,sn3191", .data = &is31fl3190_cdef, },
- { .compatible = "si-en,sn3193", .data = &is31fl3193_cdef, },
- { .compatible = "si-en,sn3196", .data = &is31fl3196_cdef, },
- { .compatible = "si-en,sn3199", .data = &is31fl3199_cdef, },
- { }
+static struct regmap_config is31fl3196_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = IS31FL3196_REG_CNT,
+ .cache_type = REGCACHE_FLAT,
+ .readable_reg = is31fl319x_readable_reg,
+ .volatile_reg = is31fl3196_volatile_reg,
+ .reg_defaults = is31fl3196_reg_defaults,
+ .num_reg_defaults = ARRAY_SIZE(is31fl3196_reg_defaults),
};
-MODULE_DEVICE_TABLE(of, of_is31fl319x_match);
static int is31fl3196_brightness_set(struct led_classdev *cdev,
enum led_brightness brightness)
@@ -175,9 +193,69 @@ static int is31fl3196_brightness_set(struct led_classdev *cdev,
return ret;
}
+static const struct is31fl319x_chipdef is31fl3190_cdef = {
+ .num_leds = 1,
+ .reset_reg = IS31FL3196_RESET,
+ .is31fl319x_regmap_config = &is31fl3196_regmap_config,
+ .brightness_set = is31fl3196_brightness_set,
+ .current_default = IS31FL3196_CURRENT_uA_DEFAULT,
+ .current_min = IS31FL3196_CURRENT_uA_MIN,
+ .current_max = IS31FL3196_CURRENT_uA_MAX,
+ .is_3196or3199 = true,
+};
+
+static const struct is31fl319x_chipdef is31fl3193_cdef = {
+ .num_leds = 3,
+ .reset_reg = IS31FL3196_RESET,
+ .is31fl319x_regmap_config = &is31fl3196_regmap_config,
+ .brightness_set = is31fl3196_brightness_set,
+ .current_default = IS31FL3196_CURRENT_uA_DEFAULT,
+ .current_min = IS31FL3196_CURRENT_uA_MIN,
+ .current_max = IS31FL3196_CURRENT_uA_MAX,
+ .is_3196or3199 = true,
+};
+
+static const struct is31fl319x_chipdef is31fl3196_cdef = {
+ .num_leds = 6,
+ .reset_reg = IS31FL3196_RESET,
+ .is31fl319x_regmap_config = &is31fl3196_regmap_config,
+ .brightness_set = is31fl3196_brightness_set,
+ .current_default = IS31FL3196_CURRENT_uA_DEFAULT,
+ .current_min = IS31FL3196_CURRENT_uA_MIN,
+ .current_max = IS31FL3196_CURRENT_uA_MAX,
+ .is_3196or3199 = true,
+};
+
+static const struct is31fl319x_chipdef is31fl3199_cdef = {
+ .num_leds = 9,
+ .reset_reg = IS31FL3196_RESET,
+ .is31fl319x_regmap_config = &is31fl3196_regmap_config,
+ .brightness_set = is31fl3196_brightness_set,
+ .current_default = IS31FL3196_CURRENT_uA_DEFAULT,
+ .current_min = IS31FL3196_CURRENT_uA_MIN,
+ .current_max = IS31FL3196_CURRENT_uA_MAX,
+ .is_3196or3199 = true,
+};
+
+static const struct of_device_id of_is31fl319x_match[] = {
+ { .compatible = "issi,is31fl3190", .data = &is31fl3190_cdef, },
+ { .compatible = "issi,is31fl3191", .data = &is31fl3190_cdef, },
+ { .compatible = "issi,is31fl3193", .data = &is31fl3193_cdef, },
+ { .compatible = "issi,is31fl3196", .data = &is31fl3196_cdef, },
+ { .compatible = "issi,is31fl3199", .data = &is31fl3199_cdef, },
+ { .compatible = "si-en,sn3190", .data = &is31fl3190_cdef, },
+ { .compatible = "si-en,sn3191", .data = &is31fl3190_cdef, },
+ { .compatible = "si-en,sn3193", .data = &is31fl3193_cdef, },
+ { .compatible = "si-en,sn3196", .data = &is31fl3196_cdef, },
+ { .compatible = "si-en,sn3199", .data = &is31fl3199_cdef, },
+ { }
+};
+MODULE_DEVICE_TABLE(of, of_is31fl319x_match);
+
static int is31fl319x_parse_child_dt(const struct device *dev,
const struct device_node *child,
- struct is31fl319x_led *led)
+ struct is31fl319x_led *led,
+ struct is31fl319x_chip *is31)
{
struct led_classdev *cdev = &led->cdev;
int ret;
@@ -190,14 +268,14 @@ static int is31fl319x_parse_child_dt(const struct device *dev,
if (ret < 0 && ret != -EINVAL) /* is optional */
return ret;
- led->max_microamp = IS31FL3196_CURRENT_uA_DEFAULT;
+ led->max_microamp = is31->cdef->current_default;
ret = of_property_read_u32(child, "led-max-microamp",
&led->max_microamp);
if (!ret) {
- if (led->max_microamp < IS31FL3196_CURRENT_uA_MIN)
+ if (led->max_microamp < is31->cdef->current_min)
return -EINVAL; /* not supported */
led->max_microamp = min(led->max_microamp,
- IS31FL3196_CURRENT_uA_MAX);
+ is31->cdef->current_max);
}
return 0;
@@ -258,7 +336,7 @@ static int is31fl319x_parse_dt(struct device *dev,
goto put_child_node;
}
- ret = is31fl319x_parse_child_dt(dev, child, led);
+ ret = is31fl319x_parse_child_dt(dev, child, led, is31);
if (ret) {
dev_err(dev, "led %u DT parsing failed\n", reg);
goto put_child_node;
@@ -268,10 +346,12 @@ static int is31fl319x_parse_dt(struct device *dev,
}
is31->audio_gain_db = 0;
- ret = of_property_read_u32(np, "audio-gain-db", &is31->audio_gain_db);
- if (!ret)
- is31->audio_gain_db = min(is31->audio_gain_db,
- IS31FL3196_AUDIO_GAIN_DB_MAX);
+ if (is31->cdef->is_3196or3199) {
+ ret = of_property_read_u32(np, "audio-gain-db", &is31->audio_gain_db);
+ if (!ret)
+ is31->audio_gain_db = min(is31->audio_gain_db,
+ IS31FL3196_AUDIO_GAIN_DB_MAX);
+ }
return 0;
@@ -280,48 +360,6 @@ static int is31fl319x_parse_dt(struct device *dev,
return ret;
}
-static bool is31fl319x_readable_reg(struct device *dev, unsigned int reg)
-{ /* we have no readable registers */
- return false;
-}
-
-static bool is31fl3196_volatile_reg(struct device *dev, unsigned int reg)
-{ /* volatile registers are not cached */
- switch (reg) {
- case IS31FL3196_DATA_UPDATE:
- case IS31FL3196_TIME_UPDATE:
- case IS31FL3196_RESET:
- return true; /* always write-through */
- default:
- return false;
- }
-}
-
-static const struct reg_default is31fl3196_reg_defaults[] = {
- { IS31FL3196_CONFIG1, 0x00},
- { IS31FL3196_CONFIG2, 0x00},
- { IS31FL3196_PWM(0), 0x00},
- { IS31FL3196_PWM(1), 0x00},
- { IS31FL3196_PWM(2), 0x00},
- { IS31FL3196_PWM(3), 0x00},
- { IS31FL3196_PWM(4), 0x00},
- { IS31FL3196_PWM(5), 0x00},
- { IS31FL3196_PWM(6), 0x00},
- { IS31FL3196_PWM(7), 0x00},
- { IS31FL3196_PWM(8), 0x00},
-};
-
-static struct regmap_config is31fl3196_regmap_config = {
- .reg_bits = 8,
- .val_bits = 8,
- .max_register = IS31FL3196_REG_CNT,
- .cache_type = REGCACHE_FLAT,
- .readable_reg = is31fl319x_readable_reg,
- .volatile_reg = is31fl3196_volatile_reg,
- .reg_defaults = is31fl3196_reg_defaults,
- .num_reg_defaults = ARRAY_SIZE(is31fl3196_reg_defaults),
-};
-
static inline int is31fl3196_microamp_to_cs(struct device *dev, u32 microamp)
{ /* round down to nearest supported value (range check done by caller) */
u32 step = microamp / IS31FL3196_CURRENT_uA_STEP;
@@ -343,7 +381,7 @@ static int is31fl319x_probe(struct i2c_client *client,
struct device *dev = &client->dev;
int err;
int i = 0;
- u32 aggregated_led_microamp = IS31FL3196_CURRENT_uA_MAX;
+ u32 aggregated_led_microamp;
if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C))
return -EIO;
@@ -365,7 +403,7 @@ static int is31fl319x_probe(struct i2c_client *client,
}
is31->client = client;
- is31->regmap = devm_regmap_init_i2c(client, &is31fl3196_regmap_config);
+ is31->regmap = devm_regmap_init_i2c(client, is31->cdef->is31fl319x_regmap_config);
if (IS_ERR(is31->regmap)) {
dev_err(&client->dev, "failed to allocate register map\n");
err = PTR_ERR(is31->regmap);
@@ -375,7 +413,7 @@ static int is31fl319x_probe(struct i2c_client *client,
i2c_set_clientdata(client, is31);
/* check for write-reply from chip (we can't read any registers) */
- err = regmap_write(is31->regmap, IS31FL3196_RESET, 0x00);
+ err = regmap_write(is31->regmap, is31->cdef->reset_reg, 0x00);
if (err < 0) {
dev_err(&client->dev, "no response from chip write: err = %d\n",
err);
@@ -388,14 +426,16 @@ static int is31fl319x_probe(struct i2c_client *client,
* But the chip does not allow to limit individual LEDs.
* So we take minimum from all subnodes for safety of hardware.
*/
+ aggregated_led_microamp = is31->cdef->current_max;
for (i = 0; i < is31->cdef->num_leds; i++)
if (is31->leds[i].configured &&
is31->leds[i].max_microamp < aggregated_led_microamp)
aggregated_led_microamp = is31->leds[i].max_microamp;
- regmap_write(is31->regmap, IS31FL3196_CONFIG2,
- is31fl3196_microamp_to_cs(dev, aggregated_led_microamp) |
- is31fl3196_db_to_gain(is31->audio_gain_db));
+ if (is31->cdef->is_3196or3199)
+ regmap_write(is31->regmap, IS31FL3196_CONFIG2,
+ is31fl3196_microamp_to_cs(dev, aggregated_led_microamp) |
+ is31fl3196_db_to_gain(is31->audio_gain_db));
for (i = 0; i < is31->cdef->num_leds; i++) {
struct is31fl319x_led *led = &is31->leds[i];
@@ -404,7 +444,7 @@ static int is31fl319x_probe(struct i2c_client *client,
continue;
led->chip = is31;
- led->cdev.brightness_set_blocking = is31fl3196_brightness_set;
+ led->cdev.brightness_set_blocking = is31->cdef->brightness_set;
err = devm_led_classdev_register(&client->dev, &led->cdev);
if (err < 0)
--
2.35.3
Add si-en compatibles for all chip variants and add conditionals
depending on compatibles to document variants specs:
- possible reg addresses
- whether audio-gain-db is supported or not
- maximum number of leds
- led-max-microamp values
Reviewed-by: Rob Herring <[email protected]>
Signed-off-by: Vincent Knecht <[email protected]>
---
.../bindings/leds/issi,is31fl319x.yaml | 84 ++++++++++++++++++-
1 file changed, 82 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/leds/issi,is31fl319x.yaml b/Documentation/devicetree/bindings/leds/issi,is31fl319x.yaml
index 0d684aeeb8cd..940333f2d69c 100644
--- a/Documentation/devicetree/bindings/leds/issi,is31fl319x.yaml
+++ b/Documentation/devicetree/bindings/leds/issi,is31fl319x.yaml
@@ -28,6 +28,10 @@ properties:
- issi,is31fl3193
- issi,is31fl3196
- issi,is31fl3199
+ - si-en,sn3190
+ - si-en,sn3191
+ - si-en,sn3193
+ - si-en,sn3196
- si-en,sn3199
reg:
@@ -61,8 +65,6 @@ patternProperties:
maximum: 9
led-max-microamp:
- default: 20000
- enum: [5000, 10000, 15000, 20000, 25000, 30000, 35000, 40000]
description:
Note that a driver will take the lowest of all LED limits
since the chip has a single global setting. The lowest value
@@ -71,6 +73,84 @@ patternProperties:
and not the current, which will always have its peak value
equal to led-max-microamp.
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - issi,is31fl3190
+ - issi,is31fl3191
+ - issi,is31fl3193
+ - si-en,sn3190
+ - si-en,sn3191
+ - si-en,sn3193
+ then:
+ properties:
+ reg:
+ enum: [0x68, 0x69, 0x6a, 0x6b]
+
+ audio-gain-db: false
+
+ patternProperties:
+ "^led@[1-9]$":
+ properties:
+ led-max-microamp:
+ default: 42000
+ enum: [5000, 10000, 17500, 30000, 42000]
+ else:
+ properties:
+ reg:
+ enum: [0x64, 0x65, 0x66, 0x67]
+
+ patternProperties:
+ "^led@[1-9]$":
+ properties:
+ led-max-microamp:
+ default: 20000
+ enum: [5000, 10000, 15000, 20000, 25000, 30000, 35000, 40000]
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - issi,is31fl3190
+ - issi,is31fl3191
+ - si-en,sn3190
+ - si-en,sn3191
+ then:
+ patternProperties:
+ "^led@[1-9]$":
+ properties:
+ reg:
+ maximum: 1
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - issi,is31fl3193
+ - si-en,sn3193
+ then:
+ patternProperties:
+ "^led@[1-9]$":
+ properties:
+ reg:
+ maximum: 3
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - issi,is31fl3196
+ - si-en,sn3196
+ then:
+ patternProperties:
+ "^led@[1-9]$":
+ properties:
+ reg:
+ maximum: 6
+
required:
- compatible
- reg
--
2.35.3
On Tue, Jul 5, 2022 at 6:32 PM Vincent Knecht <[email protected]> wrote:
>
> In order to add real support for is31fl3190, is31fl3191 and is31fl3193,
> rename variant-dependent elements to not use 319X where needed.
>
> 3190 suffix is used for is31fl3190, is31fl3191 and is31fl3193 circuits.
> 3196 suffix is used for is31fl3196 and is31fl3199.
>
> Those two groups have different register maps, current settings and even
> a different interpretation of the software shutdown bit:
> https://lumissil.com/assets/pdf/core/IS31FL3190_DS.pdf
> https://lumissil.com/assets/pdf/core/IS31FL3191_DS.pdf
> https://lumissil.com/assets/pdf/core/IS31FL3193_DS.pdf
> https://lumissil.com/assets/pdf/core/IS31FL3196_DS.pdf
> https://lumissil.com/assets/pdf/core/IS31FL3199_DS.pdf
>
> Rename variables, structures and defines in preparation of the splitting.
> No functional nor behaviour change.
...
> +static bool is31fl3196_volatile_reg(struct device *dev, unsigned int reg)
> { /* volatile registers are not cached */
This is a rather non-standard place for comments. Are you going to
address this in the future?
> }
...
> +static const struct reg_default is31fl3196_reg_defaults[] = {
> + { IS31FL3196_CONFIG1, 0x00},
> + { IS31FL3196_CONFIG2, 0x00},
> + { IS31FL3196_PWM(0), 0x00},
> + { IS31FL3196_PWM(1), 0x00},
> + { IS31FL3196_PWM(2), 0x00},
> + { IS31FL3196_PWM(3), 0x00},
> + { IS31FL3196_PWM(4), 0x00},
> + { IS31FL3196_PWM(5), 0x00},
> + { IS31FL3196_PWM(6), 0x00},
> + { IS31FL3196_PWM(7), 0x00},
> + { IS31FL3196_PWM(8), 0x00},
While at it, add a space before }. This seems in many places like
this. Perhaps address the rest in a separate patch?
> };
--
With Best Regards,
Andy Shevchenko
On Tue, Jul 5, 2022 at 6:32 PM Vincent Knecht <[email protected]> wrote:
>
> v3:
> - pick up Rob's R-b for patches 1 and 2
> - reinstate bindings docs license and maintainer
> changes with Nikolaus agreement
> - took Andy's comments on patch 4 into account
Thanks for the update. Nothing serious, but a few comments.
Also a question here. Do you have plans to convert it to use device properties?
> The is31fl3190, is31fl3191 and is31fl3193 chips (1 or 3 PWM channels)
> cannot be handled the same as is31fl3196 and is31fl3199,
> if only because the register map is different.
> Also:
> - the software shutdown bit is reversed
> - and additional field needs to be set to enable all channels
> - the led-max-microamp current values and setting are not the same
>
> Datasheets:
> https://lumissil.com/assets/pdf/core/IS31FL3190_DS.pdf
> https://lumissil.com/assets/pdf/core/IS31FL3191_DS.pdf
> https://lumissil.com/assets/pdf/core/IS31FL3193_DS.pdf
> https://lumissil.com/assets/pdf/core/IS31FL3196_DS.pdf
> https://lumissil.com/assets/pdf/core/IS31FL3199_DS.pdf
>
> This series:
>
> - converts dt-bindings to dtschema, adding all si-en compatibles
> for convenience and consistency, and adding constraints on
> supported values for eg. reg address and led-max-microamp
>
> - changes vars, structs and defines to not use 319X suffix
> but 3190 for 319{0,1,3} and 3196 for 319{6,9}
>
> - adds fields in chipdef struct for chip-specific values
>
> - only in the last patch, adds is31fl319{0,1,3} specific values
> so those chips can work.
>
> Tested on msm8916-alcatel-idol347, which probably has an
> si-en,sn3190 or si-en,sn3191 (only one white led indicator).
--
With Best Regards,
Andy Shevchenko
On Tue, Jul 5, 2022 at 6:33 PM Vincent Knecht <[email protected]> wrote:
>
> Allow setting chips' specifics in chipdef struct by adding fields for:
> - the reset register address
> - a pointer to a regmap_config struct
> - a pointer to a brightness_set function
> - current default, min and max values
> - a boolean to distinguish 319{0,1,3} and 319{6,9} chips
> and use those fields in places where distinction has to be made.
>
> The fields for 319{0,1,3} still point to 319{6,9} values.
> No functional change.
...
> +static bool is31fl319x_readable_reg(struct device *dev, unsigned int reg)
> +{ /* we have no readable registers */
Non-standard place for comments.
> + return false;
> +}
...
> +static const struct reg_default is31fl3196_reg_defaults[] = {
> + { IS31FL3196_CONFIG1, 0x00},
> + { IS31FL3196_CONFIG2, 0x00},
> + { IS31FL3196_PWM(0), 0x00},
> + { IS31FL3196_PWM(1), 0x00},
> + { IS31FL3196_PWM(2), 0x00},
> + { IS31FL3196_PWM(3), 0x00},
> + { IS31FL3196_PWM(4), 0x00},
> + { IS31FL3196_PWM(5), 0x00},
> + { IS31FL3196_PWM(6), 0x00},
> + { IS31FL3196_PWM(7), 0x00},
> + { IS31FL3196_PWM(8), 0x00},
Missed space before }.
> };
--
With Best Regards,
Andy Shevchenko
On Tue, Jul 5, 2022 at 6:32 PM Vincent Knecht <[email protected]> wrote:
>
> Set specific chipset structs values for is31fl319{0,1,3}
> so that those chips can actually work.
> Datasheets:
> https://lumissil.com/assets/pdf/core/IS31FL3190_DS.pdf
> https://lumissil.com/assets/pdf/core/IS31FL3191_DS.pdf
> https://lumissil.com/assets/pdf/core/IS31FL3193_DS.pdf
> https://lumissil.com/assets/pdf/core/IS31FL3196_DS.pdf
> https://lumissil.com/assets/pdf/core/IS31FL3199_DS.pdf
...
Two comments as per previous patch reviews.
...
> + struct is31fl319x_led *led = container_of(cdev, struct is31fl319x_led,
> + cdev);
One line?
...
> + ret = regmap_read(is31->regmap, IS31FL3190_PWM(i), &pwm_value);
> + dev_dbg(&is31->client->dev, "%s read %d: ret=%d: %d\n",
> + __func__, i, ret, pwm_value);
regmap has tracepoints Do you need to duplicate it with slow printk()?
...
> +static inline int is31fl3190_microamp_to_cs(struct device *dev, u32 microamp)
> +{
> + switch (microamp) {
> + case 5000:
> + return IS31FL3190_CURRENT_5_mA;
> + case 10000:
> + return IS31FL3190_CURRENT_10_mA;
> + case 17500:
> + return IS31FL3190_CURRENT_17dot5_mA;
> + case 30000:
> + return IS31FL3190_CURRENT_30_mA;
> + case 42000:
> + return IS31FL3190_CURRENT_42_mA;
> + default:
> + dev_warn(dev, "Unsupported current value: %d, using 5000 µA!\n", microamp);
> + }
> +
> + return IS31FL3190_CURRENT_5_mA;
It's more consistent to return directly from the default case.
> +}
--
With Best Regards,
Andy Shevchenko
Le mardi 05 juillet 2022 à 20:57 +0200, Andy Shevchenko a écrit :
> On Tue, Jul 5, 2022 at 6:32 PM Vincent Knecht <[email protected]> wrote:
> >
> > v3:
> > - pick up Rob's R-b for patches 1 and 2
> > - reinstate bindings docs license and maintainer
> > changes with Nikolaus agreement
> > - took Andy's comments on patch 4 into account
>
> Thanks for the update. Nothing serious, but a few comments.
>
> Also a question here. Do you have plans to convert it to use device properties?
Hi Andy, and thank you for the reviews.
Just sent a v4:
https://lore.kernel.org/linux-leds/[email protected]/
As for converting to device properties, it will take me some more time
since I'm not too familiar with the concepts and how to do it exactly.
Got some hints from git history, will look into that.
Also I'd like to add blink support...
On Mon, Jul 11, 2022 at 11:39 PM Andy Shevchenko
<[email protected]> wrote:
>
> On Sat, Jul 9, 2022 at 11:51 AM Vincent Knecht
> <[email protected]> wrote:
> > Le mardi 05 juillet 2022 à 20:57 +0200, Andy Shevchenko a écrit :
> > > On Tue, Jul 5, 2022 at 6:32 PM Vincent Knecht <[email protected]> wrote:
> > > >
> > > > v3:
> > > > - pick up Rob's R-b for patches 1 and 2
> > > > - reinstate bindings docs license and maintainer
> > > > changes with Nikolaus agreement
> > > > - took Andy's comments on patch 4 into account
> > >
> > > Thanks for the update. Nothing serious, but a few comments.
> > >
> > > Also a question here. Do you have plans to convert it to use device properties?
> >
> > Hi Andy, and thank you for the reviews.
> > Just sent a v4:
> > https://lore.kernel.org/linux-leds/[email protected]/
> >
> > As for converting to device properties, it will take me some more time
> > since I'm not too familiar with the concepts and how to do it exactly.
>
> I just sent a series [1] which is based on the top of yours. You can
> rebase it (it fixes a couple of subtle bugs: 1) GPIO error messaging
> during error probe, and 2) mutex destruction is out of order) or
> handle it together with yours. It seems you possess hardware, so I
> assume you at least can test it.
...missed link...
[1]: https://lore.kernel.org/linux-leds/[email protected]/
> > Got some hints from git history, will look into that.
> > Also I'd like to add blink support...
--
With Best Regards,
Andy Shevchenko
On Sat, Jul 9, 2022 at 11:51 AM Vincent Knecht
<[email protected]> wrote:
> Le mardi 05 juillet 2022 à 20:57 +0200, Andy Shevchenko a écrit :
> > On Tue, Jul 5, 2022 at 6:32 PM Vincent Knecht <[email protected]> wrote:
> > >
> > > v3:
> > > - pick up Rob's R-b for patches 1 and 2
> > > - reinstate bindings docs license and maintainer
> > > changes with Nikolaus agreement
> > > - took Andy's comments on patch 4 into account
> >
> > Thanks for the update. Nothing serious, but a few comments.
> >
> > Also a question here. Do you have plans to convert it to use device properties?
>
> Hi Andy, and thank you for the reviews.
> Just sent a v4:
> https://lore.kernel.org/linux-leds/[email protected]/
>
> As for converting to device properties, it will take me some more time
> since I'm not too familiar with the concepts and how to do it exactly.
I just sent a series [1] which is based on the top of yours. You can
rebase it (it fixes a couple of subtle bugs: 1) GPIO error messaging
during error probe, and 2) mutex destruction is out of order) or
handle it together with yours. It seems you possess hardware, so I
assume you at least can test it.
> Got some hints from git history, will look into that.
> Also I'd like to add blink support...
--
With Best Regards,
Andy Shevchenko