2021-06-08 03:25:35

by Koba Ko

[permalink] [raw]
Subject: [PATCH] [v2] r8169: Use PHY_POLL when RTL8106E enable ASPM

For RTL8106E, it's a Fast-ethernet chip.
If ASPM is enabled, the link chang interrupt wouldn't be triggered
immediately and must wait a very long time to get link change interrupt.
Even the link change interrupt isn't triggered, the phy link is already
established.

Use PHY_POLL to watch the status of phy link and disable
the link change interrupt when ASPM is enabled on RTL8106E.

v2: Instead use PHY_POLL and identify 8106E by RTL_GIGA_MAC_VER_39.

Signed-off-by: Koba Ko <[email protected]>
---
drivers/net/ethernet/realtek/r8169_main.c | 21 +++++++++++++++++++--
1 file changed, 19 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
index 2c89cde7da1e..a59cbaef2839 100644
--- a/drivers/net/ethernet/realtek/r8169_main.c
+++ b/drivers/net/ethernet/realtek/r8169_main.c
@@ -4914,6 +4914,19 @@ static const struct dev_pm_ops rtl8169_pm_ops = {

#endif /* CONFIG_PM */

+static int rtl_phy_poll_quirk(struct rtl8169_private *tp)
+{
+ struct pci_dev *pdev = tp->pci_dev;
+
+ if (!pcie_aspm_enabled(pdev))
+ return 0;
+
+ if (tp->mac_version == RTL_GIGA_MAC_VER_39)
+ return 1;
+
+ return 0;
+}
+
static void rtl_wol_shutdown_quirk(struct rtl8169_private *tp)
{
/* WoL fails with 8168b when the receiver is disabled. */
@@ -4991,7 +5004,10 @@ static const struct net_device_ops rtl_netdev_ops = {

static void rtl_set_irq_mask(struct rtl8169_private *tp)
{
- tp->irq_mask = RxOK | RxErr | TxOK | TxErr | LinkChg;
+ tp->irq_mask = RxOK | RxErr | TxOK | TxErr;
+
+ if (!rtl_phy_poll_quirk(tp))
+ tp->irq_mask |= LinkChg;

if (tp->mac_version <= RTL_GIGA_MAC_VER_06)
tp->irq_mask |= SYSErr | RxOverflow | RxFIFOOver;
@@ -5085,7 +5101,8 @@ static int r8169_mdio_register(struct rtl8169_private *tp)
new_bus->name = "r8169";
new_bus->priv = tp;
new_bus->parent = &pdev->dev;
- new_bus->irq[0] = PHY_MAC_INTERRUPT;
+ new_bus->irq[0] =
+ (rtl_phy_poll_quirk(tp) ? PHY_POLL : PHY_MAC_INTERRUPT);
snprintf(new_bus->id, MII_BUS_ID_SIZE, "r8169-%x", pci_dev_id(pdev));

new_bus->read = r8169_mdio_read_reg;
--
2.25.1


2021-06-08 08:04:19

by Heiner Kallweit

[permalink] [raw]
Subject: Re: [PATCH] [v2] r8169: Use PHY_POLL when RTL8106E enable ASPM

On 08.06.2021 05:22, Koba Ko wrote:
> For RTL8106E, it's a Fast-ethernet chip.
> If ASPM is enabled, the link chang interrupt wouldn't be triggered
> immediately and must wait a very long time to get link change interrupt.
> Even the link change interrupt isn't triggered, the phy link is already
> established.
>
> Use PHY_POLL to watch the status of phy link and disable
> the link change interrupt when ASPM is enabled on RTL8106E.
>
> v2: Instead use PHY_POLL and identify 8106E by RTL_GIGA_MAC_VER_39.
>

Still the issue description doesn't convince me that it's a hw bug
with the respective chip version. What has been stated so far:

1. (and most important) Issue doesn't occur in mainline because ASPM
is disabled in mainline for r8169. Issue occurs only with a
downstream kernel with ASPM enabled for r8169.

2. Issue occurs only with ASPM L1.1 not disabled, even though this chip
version doesn't support L1 sub-states. Just L0s/L1 don't trigger
the issue.
The NIC doesn't announce L1.1 support, therefore PCI core won't
enable L1 sub-states on the PCIe link between NIC and upstream
PCI bridge.

3. Issue occurs only with a GBit-capable link partner. 100MBit link
partners are fine. Not clear whether issue occurs with a specific
Gbit link partner only or with GBit-capable link partners in general.

4. Only link-up interrupt is affected. Not link-down and not interrupts
triggered by other interrupt sources.

5. Realtek couldn't confirm that there's such a hw bug on RTL8106e.

One thing that hasn't been asked yet:
Does issue occur always if you re-plug the cable? Or only on boot?
I'm asking because in the dmesg log you attached to the bugzilla issue
the following looks totally ok.

[ 61.651643] r8169 0000:01:00.0 enp1s0: Link is Down
[ 63.720015] r8169 0000:01:00.0 enp1s0: Link is Up - 100Mbps/Full - flow control rx/tx
[ 66.685499] r8169 0000:01:00.0 enp1s0: Link is Down

> Signed-off-by: Koba Ko <[email protected]>
> ---
> drivers/net/ethernet/realtek/r8169_main.c | 21 +++++++++++++++++++--
> 1 file changed, 19 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
> index 2c89cde7da1e..a59cbaef2839 100644
> --- a/drivers/net/ethernet/realtek/r8169_main.c
> +++ b/drivers/net/ethernet/realtek/r8169_main.c
> @@ -4914,6 +4914,19 @@ static const struct dev_pm_ops rtl8169_pm_ops = {
>
> #endif /* CONFIG_PM */
>
> +static int rtl_phy_poll_quirk(struct rtl8169_private *tp)
> +{
> + struct pci_dev *pdev = tp->pci_dev;
> +
> + if (!pcie_aspm_enabled(pdev))

That's the wrong call. According to what you said earlier you want to
check for L1 sub-states, not for ASPM in general.

> + return 0;
> +
> + if (tp->mac_version == RTL_GIGA_MAC_VER_39)
> + return 1;
> +
> + return 0;
> +}
> +
> static void rtl_wol_shutdown_quirk(struct rtl8169_private *tp)
> {
> /* WoL fails with 8168b when the receiver is disabled. */
> @@ -4991,7 +5004,10 @@ static const struct net_device_ops rtl_netdev_ops = {
>
> static void rtl_set_irq_mask(struct rtl8169_private *tp)
> {
> - tp->irq_mask = RxOK | RxErr | TxOK | TxErr | LinkChg;
> + tp->irq_mask = RxOK | RxErr | TxOK | TxErr;
> +
> + if (!rtl_phy_poll_quirk(tp))
> + tp->irq_mask |= LinkChg;
>
> if (tp->mac_version <= RTL_GIGA_MAC_VER_06)
> tp->irq_mask |= SYSErr | RxOverflow | RxFIFOOver;
> @@ -5085,7 +5101,8 @@ static int r8169_mdio_register(struct rtl8169_private *tp)
> new_bus->name = "r8169";
> new_bus->priv = tp;
> new_bus->parent = &pdev->dev;
> - new_bus->irq[0] = PHY_MAC_INTERRUPT;
> + new_bus->irq[0] =
> + (rtl_phy_poll_quirk(tp) ? PHY_POLL : PHY_MAC_INTERRUPT);
> snprintf(new_bus->id, MII_BUS_ID_SIZE, "r8169-%x", pci_dev_id(pdev));
>
> new_bus->read = r8169_mdio_read_reg;
>

2021-06-08 10:46:46

by Koba Ko

[permalink] [raw]
Subject: Re: [PATCH] [v2] r8169: Use PHY_POLL when RTL8106E enable ASPM

On Tue, Jun 8, 2021 at 4:00 PM Heiner Kallweit <[email protected]> wrote:
>
> On 08.06.2021 05:22, Koba Ko wrote:
> > For RTL8106E, it's a Fast-ethernet chip.
> > If ASPM is enabled, the link chang interrupt wouldn't be triggered
> > immediately and must wait a very long time to get link change interrupt.
> > Even the link change interrupt isn't triggered, the phy link is already
> > established.
> >
> > Use PHY_POLL to watch the status of phy link and disable
> > the link change interrupt when ASPM is enabled on RTL8106E.
> >
> > v2: Instead use PHY_POLL and identify 8106E by RTL_GIGA_MAC_VER_39.
> >
>
> Still the issue description doesn't convince me that it's a hw bug
> with the respective chip version. What has been stated so far:
>
> 1. (and most important) Issue doesn't occur in mainline because ASPM
> is disabled in mainline for r8169. Issue occurs only with a
> downstream kernel with ASPM enabled for r8169.

mainline kernel and enable L1, the issue is also observed.

> 2. Issue occurs only with ASPM L1.1 not disabled, even though this chip
> version doesn't support L1 sub-states. Just L0s/L1 don't trigger
> the issue.
> The NIC doesn't announce L1.1 support, therefore PCI core won't
> enable L1 sub-states on the PCIe link between NIC and upstream
> PCI bridge.

More precisely, when L1 is enabled, the issue would be triggered.
For RTL8106E,
1. Only disable L0s, pcie_aspm_enabled return 1, issue is triggered.
2. Only disable L1_1, pcie_aspm_enabled return 1, issue is triggered.

3. Only disable L1, pcie_aspm_enabled return 0, issue is not triggered.

>
> 3. Issue occurs only with a GBit-capable link partner. 100MBit link
> partners are fine. Not clear whether issue occurs with a specific
> Gbit link partner only or with GBit-capable link partners in general.
>
> 4. Only link-up interrupt is affected. Not link-down and not interrupts
> triggered by other interrupt sources.
>
> 5. Realtek couldn't confirm that there's such a hw bug on RTL8106e.
>
> One thing that hasn't been asked yet:
> Does issue occur always if you re-plug the cable? Or only on boot?
> I'm asking because in the dmesg log you attached to the bugzilla issue
> the following looks totally ok.
>
> [ 61.651643] r8169 0000:01:00.0 enp1s0: Link is Down
> [ 63.720015] r8169 0000:01:00.0 enp1s0: Link is Up - 100Mbps/Full - flow control rx/tx
> [ 66.685499] r8169 0000:01:00.0 enp1s0: Link is Down

Once the link is up,
1. If cable is unplug&plug immediately, you wouldn't see the issue.
2. Unplug cable and wait a long time (~1Mins), then plug the cable,
the issue appears again.

>
> > Signed-off-by: Koba Ko <[email protected]>
> > ---
> > drivers/net/ethernet/realtek/r8169_main.c | 21 +++++++++++++++++++--
> > 1 file changed, 19 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
> > index 2c89cde7da1e..a59cbaef2839 100644
> > --- a/drivers/net/ethernet/realtek/r8169_main.c
> > +++ b/drivers/net/ethernet/realtek/r8169_main.c
> > @@ -4914,6 +4914,19 @@ static const struct dev_pm_ops rtl8169_pm_ops = {
> >
> > #endif /* CONFIG_PM */
> >
> > +static int rtl_phy_poll_quirk(struct rtl8169_private *tp)
> > +{
> > + struct pci_dev *pdev = tp->pci_dev;
> > +
> > + if (!pcie_aspm_enabled(pdev))
>
> That's the wrong call. According to what you said earlier you want to
> check for L1 sub-states, not for ASPM in general.

As per described above, that's why use pcie_aspm_enabled here.

>
> > + return 0;
> > +
> > + if (tp->mac_version == RTL_GIGA_MAC_VER_39)
> > + return 1;
> > +
> > + return 0;
> > +}
> > +
> > static void rtl_wol_shutdown_quirk(struct rtl8169_private *tp)
> > {
> > /* WoL fails with 8168b when the receiver is disabled. */
> > @@ -4991,7 +5004,10 @@ static const struct net_device_ops rtl_netdev_ops = {
> >
> > static void rtl_set_irq_mask(struct rtl8169_private *tp)
> > {
> > - tp->irq_mask = RxOK | RxErr | TxOK | TxErr | LinkChg;
> > + tp->irq_mask = RxOK | RxErr | TxOK | TxErr;
> > +
> > + if (!rtl_phy_poll_quirk(tp))
> > + tp->irq_mask |= LinkChg;
> >
> > if (tp->mac_version <= RTL_GIGA_MAC_VER_06)
> > tp->irq_mask |= SYSErr | RxOverflow | RxFIFOOver;
> > @@ -5085,7 +5101,8 @@ static int r8169_mdio_register(struct rtl8169_private *tp)
> > new_bus->name = "r8169";
> > new_bus->priv = tp;
> > new_bus->parent = &pdev->dev;
> > - new_bus->irq[0] = PHY_MAC_INTERRUPT;
> > + new_bus->irq[0] =
> > + (rtl_phy_poll_quirk(tp) ? PHY_POLL : PHY_MAC_INTERRUPT);
> > snprintf(new_bus->id, MII_BUS_ID_SIZE, "r8169-%x", pci_dev_id(pdev));
> >
> > new_bus->read = r8169_mdio_read_reg;
> >
>

2021-06-08 13:48:38

by Heiner Kallweit

[permalink] [raw]
Subject: Re: [PATCH] [v2] r8169: Use PHY_POLL when RTL8106E enable ASPM

On 08.06.2021 12:43, Koba Ko wrote:
> On Tue, Jun 8, 2021 at 4:00 PM Heiner Kallweit <[email protected]> wrote:
>>
>> On 08.06.2021 05:22, Koba Ko wrote:
>>> For RTL8106E, it's a Fast-ethernet chip.
>>> If ASPM is enabled, the link chang interrupt wouldn't be triggered
>>> immediately and must wait a very long time to get link change interrupt.
>>> Even the link change interrupt isn't triggered, the phy link is already
>>> established.
>>>
>>> Use PHY_POLL to watch the status of phy link and disable
>>> the link change interrupt when ASPM is enabled on RTL8106E.
>>>
>>> v2: Instead use PHY_POLL and identify 8106E by RTL_GIGA_MAC_VER_39.
>>>
>>
>> Still the issue description doesn't convince me that it's a hw bug
>> with the respective chip version. What has been stated so far:
>>
>> 1. (and most important) Issue doesn't occur in mainline because ASPM
>> is disabled in mainline for r8169. Issue occurs only with a
>> downstream kernel with ASPM enabled for r8169.
>
> mainline kernel and enable L1, the issue is also observed.
>
Yes, but enabling L1 via sysfs is at own risk.

>> 2. Issue occurs only with ASPM L1.1 not disabled, even though this chip
>> version doesn't support L1 sub-states. Just L0s/L1 don't trigger
>> the issue.
>> The NIC doesn't announce L1.1 support, therefore PCI core won't
>> enable L1 sub-states on the PCIe link between NIC and upstream
>> PCI bridge.
>
> More precisely, when L1 is enabled, the issue would be triggered.
> For RTL8106E,
> 1. Only disable L0s, pcie_aspm_enabled return 1, issue is triggered.
> 2. Only disable L1_1, pcie_aspm_enabled return 1, issue is triggered.
>
> 3. Only disable L1, pcie_aspm_enabled return 0, issue is not triggered.
>
>>
>> 3. Issue occurs only with a GBit-capable link partner. 100MBit link
>> partners are fine. Not clear whether issue occurs with a specific
>> Gbit link partner only or with GBit-capable link partners in general.
>>
>> 4. Only link-up interrupt is affected. Not link-down and not interrupts
>> triggered by other interrupt sources.
>>
>> 5. Realtek couldn't confirm that there's such a hw bug on RTL8106e.
>>
>> One thing that hasn't been asked yet:
>> Does issue occur always if you re-plug the cable? Or only on boot?
>> I'm asking because in the dmesg log you attached to the bugzilla issue
>> the following looks totally ok.
>>
>> [ 61.651643] r8169 0000:01:00.0 enp1s0: Link is Down
>> [ 63.720015] r8169 0000:01:00.0 enp1s0: Link is Up - 100Mbps/Full - flow control rx/tx
>> [ 66.685499] r8169 0000:01:00.0 enp1s0: Link is Down
>
> Once the link is up,
> 1. If cable is unplug&plug immediately, you wouldn't see the issue.
> 2. Unplug cable and wait a long time (~1Mins), then plug the cable,
> the issue appears again.
>
This sounds runtime-pm-related. After 10s the NIC runtime-suspends,
and once the cable is re-plugged a PME is triggered that lets the
PCI core return the PCIe link from D3hot to D0.
If you re-plug the cable after such a longer time, do you see the
PCIe PME immediately in /proc/interrupts?

And if you set /sys/class/net/<if>/power/control to "on", does the
issue still occur?

>>
>>> Signed-off-by: Koba Ko <[email protected]>
>>> ---
>>> drivers/net/ethernet/realtek/r8169_main.c | 21 +++++++++++++++++++--
>>> 1 file changed, 19 insertions(+), 2 deletions(-)
>>>
>>> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
>>> index 2c89cde7da1e..a59cbaef2839 100644
>>> --- a/drivers/net/ethernet/realtek/r8169_main.c
>>> +++ b/drivers/net/ethernet/realtek/r8169_main.c
>>> @@ -4914,6 +4914,19 @@ static const struct dev_pm_ops rtl8169_pm_ops = {
>>>
>>> #endif /* CONFIG_PM */
>>>
>>> +static int rtl_phy_poll_quirk(struct rtl8169_private *tp)
>>> +{
>>> + struct pci_dev *pdev = tp->pci_dev;
>>> +
>>> + if (!pcie_aspm_enabled(pdev))
>>
>> That's the wrong call. According to what you said earlier you want to
>> check for L1 sub-states, not for ASPM in general.
>
> As per described above, that's why use pcie_aspm_enabled here.
>
>>
>>> + return 0;
>>> +
>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_39)
>>> + return 1;
>>> +
>>> + return 0;
>>> +}
>>> +
>>> static void rtl_wol_shutdown_quirk(struct rtl8169_private *tp)
>>> {
>>> /* WoL fails with 8168b when the receiver is disabled. */
>>> @@ -4991,7 +5004,10 @@ static const struct net_device_ops rtl_netdev_ops = {
>>>
>>> static void rtl_set_irq_mask(struct rtl8169_private *tp)
>>> {
>>> - tp->irq_mask = RxOK | RxErr | TxOK | TxErr | LinkChg;
>>> + tp->irq_mask = RxOK | RxErr | TxOK | TxErr;
>>> +
>>> + if (!rtl_phy_poll_quirk(tp))
>>> + tp->irq_mask |= LinkChg;
>>>
>>> if (tp->mac_version <= RTL_GIGA_MAC_VER_06)
>>> tp->irq_mask |= SYSErr | RxOverflow | RxFIFOOver;
>>> @@ -5085,7 +5101,8 @@ static int r8169_mdio_register(struct rtl8169_private *tp)
>>> new_bus->name = "r8169";
>>> new_bus->priv = tp;
>>> new_bus->parent = &pdev->dev;
>>> - new_bus->irq[0] = PHY_MAC_INTERRUPT;
>>> + new_bus->irq[0] =
>>> + (rtl_phy_poll_quirk(tp) ? PHY_POLL : PHY_MAC_INTERRUPT);
>>> snprintf(new_bus->id, MII_BUS_ID_SIZE, "r8169-%x", pci_dev_id(pdev));
>>>
>>> new_bus->read = r8169_mdio_read_reg;
>>>
>>

2021-06-08 14:19:45

by Koba Ko

[permalink] [raw]
Subject: Re: [PATCH] [v2] r8169: Use PHY_POLL when RTL8106E enable ASPM

On Tue, Jun 8, 2021 at 9:45 PM Heiner Kallweit <[email protected]> wrote:
>
> On 08.06.2021 12:43, Koba Ko wrote:
> > On Tue, Jun 8, 2021 at 4:00 PM Heiner Kallweit <[email protected]> wrote:
> >>
> >> On 08.06.2021 05:22, Koba Ko wrote:
> >>> For RTL8106E, it's a Fast-ethernet chip.
> >>> If ASPM is enabled, the link chang interrupt wouldn't be triggered
> >>> immediately and must wait a very long time to get link change interrupt.
> >>> Even the link change interrupt isn't triggered, the phy link is already
> >>> established.
> >>>
> >>> Use PHY_POLL to watch the status of phy link and disable
> >>> the link change interrupt when ASPM is enabled on RTL8106E.
> >>>
> >>> v2: Instead use PHY_POLL and identify 8106E by RTL_GIGA_MAC_VER_39.
> >>>
> >>
> >> Still the issue description doesn't convince me that it's a hw bug
> >> with the respective chip version. What has been stated so far:
> >>
> >> 1. (and most important) Issue doesn't occur in mainline because ASPM
> >> is disabled in mainline for r8169. Issue occurs only with a
> >> downstream kernel with ASPM enabled for r8169.
> >
> > mainline kernel and enable L1, the issue is also observed.
> >
> Yes, but enabling L1 via sysfs is at own risk.

but we could have a workaround if hw have an aspm issue.

>
> >> 2. Issue occurs only with ASPM L1.1 not disabled, even though this chip
> >> version doesn't support L1 sub-states. Just L0s/L1 don't trigger
> >> the issue.
> >> The NIC doesn't announce L1.1 support, therefore PCI core won't
> >> enable L1 sub-states on the PCIe link between NIC and upstream
> >> PCI bridge.
> >
> > More precisely, when L1 is enabled, the issue would be triggered.
> > For RTL8106E,
> > 1. Only disable L0s, pcie_aspm_enabled return 1, issue is triggered.
> > 2. Only disable L1_1, pcie_aspm_enabled return 1, issue is triggered.
> >
> > 3. Only disable L1, pcie_aspm_enabled return 0, issue is not triggered.
> >
> >>
> >> 3. Issue occurs only with a GBit-capable link partner. 100MBit link
> >> partners are fine. Not clear whether issue occurs with a specific
> >> Gbit link partner only or with GBit-capable link partners in general.
> >>
> >> 4. Only link-up interrupt is affected. Not link-down and not interrupts
> >> triggered by other interrupt sources.
> >>
> >> 5. Realtek couldn't confirm that there's such a hw bug on RTL8106e.
> >>
> >> One thing that hasn't been asked yet:
> >> Does issue occur always if you re-plug the cable? Or only on boot?
> >> I'm asking because in the dmesg log you attached to the bugzilla issue
> >> the following looks totally ok.
> >>
> >> [ 61.651643] r8169 0000:01:00.0 enp1s0: Link is Down
> >> [ 63.720015] r8169 0000:01:00.0 enp1s0: Link is Up - 100Mbps/Full - flow control rx/tx
> >> [ 66.685499] r8169 0000:01:00.0 enp1s0: Link is Down
> >
> > Once the link is up,
> > 1. If cable is unplug&plug immediately, you wouldn't see the issue.
> > 2. Unplug cable and wait a long time (~1Mins), then plug the cable,
> > the issue appears again.
> >
> This sounds runtime-pm-related. After 10s the NIC runtime-suspends,
> and once the cable is re-plugged a PME is triggered that lets the
> PCI core return the PCIe link from D3hot to D0.
> If you re-plug the cable after such a longer time, do you see the
> PCIe PME immediately in /proc/interrupts?

I don't know which irq number is for RTL8106e PME, but check all PME
in /proc/interrupt,

There's no interrupt increase on all PME entries and rtl8106e irq entry(irq 32).

>
> And if you set /sys/class/net/<if>/power/control to "on", does the
> issue still occur?

Yes, after echo "on" to /sys/class/net/<if>/power/control and
replugging the cable, the issue is still caught.
>
> >>
> >>> Signed-off-by: Koba Ko <[email protected]>
> >>> ---
> >>> drivers/net/ethernet/realtek/r8169_main.c | 21 +++++++++++++++++++--
> >>> 1 file changed, 19 insertions(+), 2 deletions(-)
> >>>
> >>> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
> >>> index 2c89cde7da1e..a59cbaef2839 100644
> >>> --- a/drivers/net/ethernet/realtek/r8169_main.c
> >>> +++ b/drivers/net/ethernet/realtek/r8169_main.c
> >>> @@ -4914,6 +4914,19 @@ static const struct dev_pm_ops rtl8169_pm_ops = {
> >>>
> >>> #endif /* CONFIG_PM */
> >>>
> >>> +static int rtl_phy_poll_quirk(struct rtl8169_private *tp)
> >>> +{
> >>> + struct pci_dev *pdev = tp->pci_dev;
> >>> +
> >>> + if (!pcie_aspm_enabled(pdev))
> >>
> >> That's the wrong call. According to what you said earlier you want to
> >> check for L1 sub-states, not for ASPM in general.
> >
> > As per described above, that's why use pcie_aspm_enabled here.
> >
> >>
> >>> + return 0;
> >>> +
> >>> + if (tp->mac_version == RTL_GIGA_MAC_VER_39)
> >>> + return 1;
> >>> +
> >>> + return 0;
> >>> +}
> >>> +
> >>> static void rtl_wol_shutdown_quirk(struct rtl8169_private *tp)
> >>> {
> >>> /* WoL fails with 8168b when the receiver is disabled. */
> >>> @@ -4991,7 +5004,10 @@ static const struct net_device_ops rtl_netdev_ops = {
> >>>
> >>> static void rtl_set_irq_mask(struct rtl8169_private *tp)
> >>> {
> >>> - tp->irq_mask = RxOK | RxErr | TxOK | TxErr | LinkChg;
> >>> + tp->irq_mask = RxOK | RxErr | TxOK | TxErr;
> >>> +
> >>> + if (!rtl_phy_poll_quirk(tp))
> >>> + tp->irq_mask |= LinkChg;
> >>>
> >>> if (tp->mac_version <= RTL_GIGA_MAC_VER_06)
> >>> tp->irq_mask |= SYSErr | RxOverflow | RxFIFOOver;
> >>> @@ -5085,7 +5101,8 @@ static int r8169_mdio_register(struct rtl8169_private *tp)
> >>> new_bus->name = "r8169";
> >>> new_bus->priv = tp;
> >>> new_bus->parent = &pdev->dev;
> >>> - new_bus->irq[0] = PHY_MAC_INTERRUPT;
> >>> + new_bus->irq[0] =
> >>> + (rtl_phy_poll_quirk(tp) ? PHY_POLL : PHY_MAC_INTERRUPT);
> >>> snprintf(new_bus->id, MII_BUS_ID_SIZE, "r8169-%x", pci_dev_id(pdev));
> >>>
> >>> new_bus->read = r8169_mdio_read_reg;
> >>>
> >>
>

2021-06-08 21:02:00

by Heiner Kallweit

[permalink] [raw]
Subject: Re: [PATCH] [v2] r8169: Use PHY_POLL when RTL8106E enable ASPM

On 08.06.2021 16:17, Koba Ko wrote:
> On Tue, Jun 8, 2021 at 9:45 PM Heiner Kallweit <[email protected]> wrote:
>>
>> On 08.06.2021 12:43, Koba Ko wrote:
>>> On Tue, Jun 8, 2021 at 4:00 PM Heiner Kallweit <[email protected]> wrote:
>>>>
>>>> On 08.06.2021 05:22, Koba Ko wrote:
>>>>> For RTL8106E, it's a Fast-ethernet chip.
>>>>> If ASPM is enabled, the link chang interrupt wouldn't be triggered
>>>>> immediately and must wait a very long time to get link change interrupt.
>>>>> Even the link change interrupt isn't triggered, the phy link is already
>>>>> established.
>>>>>
>>>>> Use PHY_POLL to watch the status of phy link and disable
>>>>> the link change interrupt when ASPM is enabled on RTL8106E.
>>>>>
>>>>> v2: Instead use PHY_POLL and identify 8106E by RTL_GIGA_MAC_VER_39.
>>>>>
>>>>
>>>> Still the issue description doesn't convince me that it's a hw bug
>>>> with the respective chip version. What has been stated so far:
>>>>
>>>> 1. (and most important) Issue doesn't occur in mainline because ASPM
>>>> is disabled in mainline for r8169. Issue occurs only with a
>>>> downstream kernel with ASPM enabled for r8169.
>>>
>>> mainline kernel and enable L1, the issue is also observed.
>>>
>> Yes, but enabling L1 via sysfs is at own risk.
>
> but we could have a workaround if hw have an aspm issue.
>
>>
>>>> 2. Issue occurs only with ASPM L1.1 not disabled, even though this chip
>>>> version doesn't support L1 sub-states. Just L0s/L1 don't trigger
>>>> the issue.
>>>> The NIC doesn't announce L1.1 support, therefore PCI core won't
>>>> enable L1 sub-states on the PCIe link between NIC and upstream
>>>> PCI bridge.
>>>
>>> More precisely, when L1 is enabled, the issue would be triggered.
>>> For RTL8106E,
>>> 1. Only disable L0s, pcie_aspm_enabled return 1, issue is triggered.
>>> 2. Only disable L1_1, pcie_aspm_enabled return 1, issue is triggered.
>>>
>>> 3. Only disable L1, pcie_aspm_enabled return 0, issue is not triggered.
>>>
>>>>
>>>> 3. Issue occurs only with a GBit-capable link partner. 100MBit link
>>>> partners are fine. Not clear whether issue occurs with a specific
>>>> Gbit link partner only or with GBit-capable link partners in general.
>>>>
>>>> 4. Only link-up interrupt is affected. Not link-down and not interrupts
>>>> triggered by other interrupt sources.
>>>>
>>>> 5. Realtek couldn't confirm that there's such a hw bug on RTL8106e.
>>>>
>>>> One thing that hasn't been asked yet:
>>>> Does issue occur always if you re-plug the cable? Or only on boot?
>>>> I'm asking because in the dmesg log you attached to the bugzilla issue
>>>> the following looks totally ok.
>>>>
>>>> [ 61.651643] r8169 0000:01:00.0 enp1s0: Link is Down
>>>> [ 63.720015] r8169 0000:01:00.0 enp1s0: Link is Up - 100Mbps/Full - flow control rx/tx
>>>> [ 66.685499] r8169 0000:01:00.0 enp1s0: Link is Down
>>>
>>> Once the link is up,
>>> 1. If cable is unplug&plug immediately, you wouldn't see the issue.
>>> 2. Unplug cable and wait a long time (~1Mins), then plug the cable,
>>> the issue appears again.
>>>
>> This sounds runtime-pm-related. After 10s the NIC runtime-suspends,
>> and once the cable is re-plugged a PME is triggered that lets the
>> PCI core return the PCIe link from D3hot to D0.
>> If you re-plug the cable after such a longer time, do you see the
>> PCIe PME immediately in /proc/interrupts?
>
> I don't know which irq number is for RTL8106e PME, but check all PME
> in /proc/interrupt,
>
> There's no interrupt increase on all PME entries and rtl8106e irq entry(irq 32).
>
>>
>> And if you set /sys/class/net/<if>/power/control to "on", does the
>> issue still occur?
>
> Yes, after echo "on" to /sys/class/net/<if>/power/control and
> replugging the cable, the issue is still caught.
>>
>>>>
>>>>> Signed-off-by: Koba Ko <[email protected]>
>>>>> ---
>>>>> drivers/net/ethernet/realtek/r8169_main.c | 21 +++++++++++++++++++--
>>>>> 1 file changed, 19 insertions(+), 2 deletions(-)
>>>>>
>>>>> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
>>>>> index 2c89cde7da1e..a59cbaef2839 100644
>>>>> --- a/drivers/net/ethernet/realtek/r8169_main.c
>>>>> +++ b/drivers/net/ethernet/realtek/r8169_main.c
>>>>> @@ -4914,6 +4914,19 @@ static const struct dev_pm_ops rtl8169_pm_ops = {
>>>>>
>>>>> #endif /* CONFIG_PM */
>>>>>
>>>>> +static int rtl_phy_poll_quirk(struct rtl8169_private *tp)
>>>>> +{
>>>>> + struct pci_dev *pdev = tp->pci_dev;
>>>>> +
>>>>> + if (!pcie_aspm_enabled(pdev))
>>>>
>>>> That's the wrong call. According to what you said earlier you want to
>>>> check for L1 sub-states, not for ASPM in general.
>>>
>>> As per described above, that's why use pcie_aspm_enabled here.
>>>
>>>>
>>>>> + return 0;
>>>>> +
>>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_39)
>>>>> + return 1;
>>>>> +
>>>>> + return 0;
>>>>> +}
>>>>> +
>>>>> static void rtl_wol_shutdown_quirk(struct rtl8169_private *tp)
>>>>> {
>>>>> /* WoL fails with 8168b when the receiver is disabled. */
>>>>> @@ -4991,7 +5004,10 @@ static const struct net_device_ops rtl_netdev_ops = {
>>>>>
>>>>> static void rtl_set_irq_mask(struct rtl8169_private *tp)
>>>>> {
>>>>> - tp->irq_mask = RxOK | RxErr | TxOK | TxErr | LinkChg;
>>>>> + tp->irq_mask = RxOK | RxErr | TxOK | TxErr;
>>>>> +
>>>>> + if (!rtl_phy_poll_quirk(tp))
>>>>> + tp->irq_mask |= LinkChg;
>>>>>
>>>>> if (tp->mac_version <= RTL_GIGA_MAC_VER_06)
>>>>> tp->irq_mask |= SYSErr | RxOverflow | RxFIFOOver;
>>>>> @@ -5085,7 +5101,8 @@ static int r8169_mdio_register(struct rtl8169_private *tp)
>>>>> new_bus->name = "r8169";
>>>>> new_bus->priv = tp;
>>>>> new_bus->parent = &pdev->dev;
>>>>> - new_bus->irq[0] = PHY_MAC_INTERRUPT;
>>>>> + new_bus->irq[0] =
>>>>> + (rtl_phy_poll_quirk(tp) ? PHY_POLL : PHY_MAC_INTERRUPT);
>>>>> snprintf(new_bus->id, MII_BUS_ID_SIZE, "r8169-%x", pci_dev_id(pdev));
>>>>>
>>>>> new_bus->read = r8169_mdio_read_reg;
>>>>>
>>>>
>>

The r8101 vendor driver applies a special setting for RTL8106e if ASPM is enabled.
Not sure whether it's related but it's worth a try. Could you please check whether
the following makes a difference?

diff --git a/drivers/net/ethernet/realtek/r8169_phy_config.c b/drivers/net/ethernet/realtek/r8169_phy_config.c
index 50f0f621b..60014b9c4 100644
--- a/drivers/net/ethernet/realtek/r8169_phy_config.c
+++ b/drivers/net/ethernet/realtek/r8169_phy_config.c
@@ -1153,6 +1153,7 @@ static void rtl8106e_hw_phy_config(struct rtl8169_private *tp,
r8169_apply_firmware(tp);

rtl_writephy_batch(phydev, phy_reg_init);
+ phy_write(phydev, 0x18, 0x8310);
}

static void rtl8125_legacy_force_mode(struct phy_device *phydev)
--
2.32.0


2021-06-09 15:40:38

by Heiner Kallweit

[permalink] [raw]
Subject: Re: [PATCH] [v2] r8169: Use PHY_POLL when RTL8106E enable ASPM

On 09.06.2021 03:47, Koba Ko wrote:
> On Wed, Jun 9, 2021 at 4:58 AM Heiner Kallweit <[email protected]> wrote:
>>
>> On 08.06.2021 16:17, Koba Ko wrote:
>>> On Tue, Jun 8, 2021 at 9:45 PM Heiner Kallweit <[email protected]> wrote:
>>>>
>>>> On 08.06.2021 12:43, Koba Ko wrote:
>>>>> On Tue, Jun 8, 2021 at 4:00 PM Heiner Kallweit <[email protected]> wrote:
>>>>>>
>>>>>> On 08.06.2021 05:22, Koba Ko wrote:
>>>>>>> For RTL8106E, it's a Fast-ethernet chip.
>>>>>>> If ASPM is enabled, the link chang interrupt wouldn't be triggered
>>>>>>> immediately and must wait a very long time to get link change interrupt.
>>>>>>> Even the link change interrupt isn't triggered, the phy link is already
>>>>>>> established.
>>>>>>>
>>>>>>> Use PHY_POLL to watch the status of phy link and disable
>>>>>>> the link change interrupt when ASPM is enabled on RTL8106E.
>>>>>>>
>>>>>>> v2: Instead use PHY_POLL and identify 8106E by RTL_GIGA_MAC_VER_39.
>>>>>>>
>>>>>>
>>>>>> Still the issue description doesn't convince me that it's a hw bug
>>>>>> with the respective chip version. What has been stated so far:
>>>>>>
>>>>>> 1. (and most important) Issue doesn't occur in mainline because ASPM
>>>>>> is disabled in mainline for r8169. Issue occurs only with a
>>>>>> downstream kernel with ASPM enabled for r8169.
>>>>>
>>>>> mainline kernel and enable L1, the issue is also observed.
>>>>>
>>>> Yes, but enabling L1 via sysfs is at own risk.
>>>
>>> but we could have a workaround if hw have an aspm issue.
>>>
>>>>
>>>>>> 2. Issue occurs only with ASPM L1.1 not disabled, even though this chip
>>>>>> version doesn't support L1 sub-states. Just L0s/L1 don't trigger
>>>>>> the issue.
>>>>>> The NIC doesn't announce L1.1 support, therefore PCI core won't
>>>>>> enable L1 sub-states on the PCIe link between NIC and upstream
>>>>>> PCI bridge.
>>>>>
>>>>> More precisely, when L1 is enabled, the issue would be triggered.
>>>>> For RTL8106E,
>>>>> 1. Only disable L0s, pcie_aspm_enabled return 1, issue is triggered.
>>>>> 2. Only disable L1_1, pcie_aspm_enabled return 1, issue is triggered.
>>>>>
>>>>> 3. Only disable L1, pcie_aspm_enabled return 0, issue is not triggered.
>>>>>
>>>>>>
>>>>>> 3. Issue occurs only with a GBit-capable link partner. 100MBit link
>>>>>> partners are fine. Not clear whether issue occurs with a specific
>>>>>> Gbit link partner only or with GBit-capable link partners in general.
>>>>>>
>>>>>> 4. Only link-up interrupt is affected. Not link-down and not interrupts
>>>>>> triggered by other interrupt sources.
>>>>>>
>>>>>> 5. Realtek couldn't confirm that there's such a hw bug on RTL8106e.
>>>>>>
>>>>>> One thing that hasn't been asked yet:
>>>>>> Does issue occur always if you re-plug the cable? Or only on boot?
>>>>>> I'm asking because in the dmesg log you attached to the bugzilla issue
>>>>>> the following looks totally ok.
>>>>>>
>>>>>> [ 61.651643] r8169 0000:01:00.0 enp1s0: Link is Down
>>>>>> [ 63.720015] r8169 0000:01:00.0 enp1s0: Link is Up - 100Mbps/Full - flow control rx/tx
>>>>>> [ 66.685499] r8169 0000:01:00.0 enp1s0: Link is Down
>>>>>
>>>>> Once the link is up,
>>>>> 1. If cable is unplug&plug immediately, you wouldn't see the issue.
>>>>> 2. Unplug cable and wait a long time (~1Mins), then plug the cable,
>>>>> the issue appears again.
>>>>>
>>>> This sounds runtime-pm-related. After 10s the NIC runtime-suspends,
>>>> and once the cable is re-plugged a PME is triggered that lets the
>>>> PCI core return the PCIe link from D3hot to D0.
>>>> If you re-plug the cable after such a longer time, do you see the
>>>> PCIe PME immediately in /proc/interrupts?
>>>
>>> I don't know which irq number is for RTL8106e PME, but check all PME
>>> in /proc/interrupt,
>>>
>>> There's no interrupt increase on all PME entries and rtl8106e irq entry(irq 32).
>>>
>>>>
>>>> And if you set /sys/class/net/<if>/power/control to "on", does the
>>>> issue still occur?
>>>
>>> Yes, after echo "on" to /sys/class/net/<if>/power/control and
>>> replugging the cable, the issue is still caught.
>>>>
>>>>>>
>>>>>>> Signed-off-by: Koba Ko <[email protected]>
>>>>>>> ---
>>>>>>> drivers/net/ethernet/realtek/r8169_main.c | 21 +++++++++++++++++++--
>>>>>>> 1 file changed, 19 insertions(+), 2 deletions(-)
>>>>>>>
>>>>>>> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
>>>>>>> index 2c89cde7da1e..a59cbaef2839 100644
>>>>>>> --- a/drivers/net/ethernet/realtek/r8169_main.c
>>>>>>> +++ b/drivers/net/ethernet/realtek/r8169_main.c
>>>>>>> @@ -4914,6 +4914,19 @@ static const struct dev_pm_ops rtl8169_pm_ops = {
>>>>>>>
>>>>>>> #endif /* CONFIG_PM */
>>>>>>>
>>>>>>> +static int rtl_phy_poll_quirk(struct rtl8169_private *tp)
>>>>>>> +{
>>>>>>> + struct pci_dev *pdev = tp->pci_dev;
>>>>>>> +
>>>>>>> + if (!pcie_aspm_enabled(pdev))
>>>>>>
>>>>>> That's the wrong call. According to what you said earlier you want to
>>>>>> check for L1 sub-states, not for ASPM in general.
>>>>>
>>>>> As per described above, that's why use pcie_aspm_enabled here.
>>>>>
>>>>>>
>>>>>>> + return 0;
>>>>>>> +
>>>>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_39)
>>>>>>> + return 1;
>>>>>>> +
>>>>>>> + return 0;
>>>>>>> +}
>>>>>>> +
>>>>>>> static void rtl_wol_shutdown_quirk(struct rtl8169_private *tp)
>>>>>>> {
>>>>>>> /* WoL fails with 8168b when the receiver is disabled. */
>>>>>>> @@ -4991,7 +5004,10 @@ static const struct net_device_ops rtl_netdev_ops = {
>>>>>>>
>>>>>>> static void rtl_set_irq_mask(struct rtl8169_private *tp)
>>>>>>> {
>>>>>>> - tp->irq_mask = RxOK | RxErr | TxOK | TxErr | LinkChg;
>>>>>>> + tp->irq_mask = RxOK | RxErr | TxOK | TxErr;
>>>>>>> +
>>>>>>> + if (!rtl_phy_poll_quirk(tp))
>>>>>>> + tp->irq_mask |= LinkChg;
>>>>>>>
>>>>>>> if (tp->mac_version <= RTL_GIGA_MAC_VER_06)
>>>>>>> tp->irq_mask |= SYSErr | RxOverflow | RxFIFOOver;
>>>>>>> @@ -5085,7 +5101,8 @@ static int r8169_mdio_register(struct rtl8169_private *tp)
>>>>>>> new_bus->name = "r8169";
>>>>>>> new_bus->priv = tp;
>>>>>>> new_bus->parent = &pdev->dev;
>>>>>>> - new_bus->irq[0] = PHY_MAC_INTERRUPT;
>>>>>>> + new_bus->irq[0] =
>>>>>>> + (rtl_phy_poll_quirk(tp) ? PHY_POLL : PHY_MAC_INTERRUPT);
>>>>>>> snprintf(new_bus->id, MII_BUS_ID_SIZE, "r8169-%x", pci_dev_id(pdev));
>>>>>>>
>>>>>>> new_bus->read = r8169_mdio_read_reg;
>>>>>>>
>>>>>>
>>>>
>>
>> The r8101 vendor driver applies a special setting for RTL8106e if ASPM is enabled.
>> Not sure whether it's related but it's worth a try. Could you please check whether
>> the following makes a difference?
>
> After applying this patch, it can't help relieve the issue.
> The 8101 vendor driver also use polling method to watch the link change event.
> Tried to disable polling method and enable LinkChg Irq, but it also
> can't get LinkChg interrupt.
>
OK, thanks for testing.
As it is now, rtl_phy_poll_quirk() would always return false because ASPM
is disabled on driver load. Changing ASPM settings can be done later via sysfs
if supported by device and upstream bridge. In addition:
- If you want to return a bool, declare the return value as bool.
- You shouldn't have to disable the LinkChg interrupt. The interrupt just triggers
a phylib state machine run what may result in a faster link-up signal even
when using polling.

By the way: All Realtek vendor drivers (r8101, r8168, r8125) don't use the LinkChg
interrupt. However I don't think this is because of known hw issues, more likely
it's because they don't use phylib and thought polling is the easier approach.
At least for r8169 I haven't heard yet of any complain regarding the LinkChg
interrupt.

>>
>> diff --git a/drivers/net/ethernet/realtek/r8169_phy_config.c b/drivers/net/ethernet/realtek/r8169_phy_config.c
>> index 50f0f621b..60014b9c4 100644
>> --- a/drivers/net/ethernet/realtek/r8169_phy_config.c
>> +++ b/drivers/net/ethernet/realtek/r8169_phy_config.c
>> @@ -1153,6 +1153,7 @@ static void rtl8106e_hw_phy_config(struct rtl8169_private *tp,
>> r8169_apply_firmware(tp);
>>
>> rtl_writephy_batch(phydev, phy_reg_init);
>> + phy_write(phydev, 0x18, 0x8310);
>> }
>>
>> static void rtl8125_legacy_force_mode(struct phy_device *phydev)
>> --
>> 2.32.0
>>
>>

2021-06-09 16:21:19

by Koba Ko

[permalink] [raw]
Subject: Re: [PATCH] [v2] r8169: Use PHY_POLL when RTL8106E enable ASPM

On Wed, Jun 9, 2021 at 10:29 PM Heiner Kallweit <[email protected]> wrote:
>
> On 09.06.2021 03:47, Koba Ko wrote:
> > On Wed, Jun 9, 2021 at 4:58 AM Heiner Kallweit <[email protected]> wrote:
> >>
> >> On 08.06.2021 16:17, Koba Ko wrote:
> >>> On Tue, Jun 8, 2021 at 9:45 PM Heiner Kallweit <[email protected]> wrote:
> >>>>
> >>>> On 08.06.2021 12:43, Koba Ko wrote:
> >>>>> On Tue, Jun 8, 2021 at 4:00 PM Heiner Kallweit <[email protected]> wrote:
> >>>>>>
> >>>>>> On 08.06.2021 05:22, Koba Ko wrote:
> >>>>>>> For RTL8106E, it's a Fast-ethernet chip.
> >>>>>>> If ASPM is enabled, the link chang interrupt wouldn't be triggered
> >>>>>>> immediately and must wait a very long time to get link change interrupt.
> >>>>>>> Even the link change interrupt isn't triggered, the phy link is already
> >>>>>>> established.
> >>>>>>>
> >>>>>>> Use PHY_POLL to watch the status of phy link and disable
> >>>>>>> the link change interrupt when ASPM is enabled on RTL8106E.
> >>>>>>>
> >>>>>>> v2: Instead use PHY_POLL and identify 8106E by RTL_GIGA_MAC_VER_39.
> >>>>>>>
> >>>>>>
> >>>>>> Still the issue description doesn't convince me that it's a hw bug
> >>>>>> with the respective chip version. What has been stated so far:
> >>>>>>
> >>>>>> 1. (and most important) Issue doesn't occur in mainline because ASPM
> >>>>>> is disabled in mainline for r8169. Issue occurs only with a
> >>>>>> downstream kernel with ASPM enabled for r8169.
> >>>>>
> >>>>> mainline kernel and enable L1, the issue is also observed.
> >>>>>
> >>>> Yes, but enabling L1 via sysfs is at own risk.
> >>>
> >>> but we could have a workaround if hw have an aspm issue.
> >>>
> >>>>
> >>>>>> 2. Issue occurs only with ASPM L1.1 not disabled, even though this chip
> >>>>>> version doesn't support L1 sub-states. Just L0s/L1 don't trigger
> >>>>>> the issue.
> >>>>>> The NIC doesn't announce L1.1 support, therefore PCI core won't
> >>>>>> enable L1 sub-states on the PCIe link between NIC and upstream
> >>>>>> PCI bridge.
> >>>>>
> >>>>> More precisely, when L1 is enabled, the issue would be triggered.
> >>>>> For RTL8106E,
> >>>>> 1. Only disable L0s, pcie_aspm_enabled return 1, issue is triggered.
> >>>>> 2. Only disable L1_1, pcie_aspm_enabled return 1, issue is triggered.
> >>>>>
> >>>>> 3. Only disable L1, pcie_aspm_enabled return 0, issue is not triggered.
> >>>>>
> >>>>>>
> >>>>>> 3. Issue occurs only with a GBit-capable link partner. 100MBit link
> >>>>>> partners are fine. Not clear whether issue occurs with a specific
> >>>>>> Gbit link partner only or with GBit-capable link partners in general.
> >>>>>>
> >>>>>> 4. Only link-up interrupt is affected. Not link-down and not interrupts
> >>>>>> triggered by other interrupt sources.
> >>>>>>
> >>>>>> 5. Realtek couldn't confirm that there's such a hw bug on RTL8106e.
> >>>>>>
> >>>>>> One thing that hasn't been asked yet:
> >>>>>> Does issue occur always if you re-plug the cable? Or only on boot?
> >>>>>> I'm asking because in the dmesg log you attached to the bugzilla issue
> >>>>>> the following looks totally ok.
> >>>>>>
> >>>>>> [ 61.651643] r8169 0000:01:00.0 enp1s0: Link is Down
> >>>>>> [ 63.720015] r8169 0000:01:00.0 enp1s0: Link is Up - 100Mbps/Full - flow control rx/tx
> >>>>>> [ 66.685499] r8169 0000:01:00.0 enp1s0: Link is Down
> >>>>>
> >>>>> Once the link is up,
> >>>>> 1. If cable is unplug&plug immediately, you wouldn't see the issue.
> >>>>> 2. Unplug cable and wait a long time (~1Mins), then plug the cable,
> >>>>> the issue appears again.
> >>>>>
> >>>> This sounds runtime-pm-related. After 10s the NIC runtime-suspends,
> >>>> and once the cable is re-plugged a PME is triggered that lets the
> >>>> PCI core return the PCIe link from D3hot to D0.
> >>>> If you re-plug the cable after such a longer time, do you see the
> >>>> PCIe PME immediately in /proc/interrupts?
> >>>
> >>> I don't know which irq number is for RTL8106e PME, but check all PME
> >>> in /proc/interrupt,
> >>>
> >>> There's no interrupt increase on all PME entries and rtl8106e irq entry(irq 32).
> >>>
> >>>>
> >>>> And if you set /sys/class/net/<if>/power/control to "on", does the
> >>>> issue still occur?
> >>>
> >>> Yes, after echo "on" to /sys/class/net/<if>/power/control and
> >>> replugging the cable, the issue is still caught.
> >>>>
> >>>>>>
> >>>>>>> Signed-off-by: Koba Ko <[email protected]>
> >>>>>>> ---
> >>>>>>> drivers/net/ethernet/realtek/r8169_main.c | 21 +++++++++++++++++++--
> >>>>>>> 1 file changed, 19 insertions(+), 2 deletions(-)
> >>>>>>>
> >>>>>>> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
> >>>>>>> index 2c89cde7da1e..a59cbaef2839 100644
> >>>>>>> --- a/drivers/net/ethernet/realtek/r8169_main.c
> >>>>>>> +++ b/drivers/net/ethernet/realtek/r8169_main.c
> >>>>>>> @@ -4914,6 +4914,19 @@ static const struct dev_pm_ops rtl8169_pm_ops = {
> >>>>>>>
> >>>>>>> #endif /* CONFIG_PM */
> >>>>>>>
> >>>>>>> +static int rtl_phy_poll_quirk(struct rtl8169_private *tp)
> >>>>>>> +{
> >>>>>>> + struct pci_dev *pdev = tp->pci_dev;
> >>>>>>> +
> >>>>>>> + if (!pcie_aspm_enabled(pdev))
> >>>>>>
> >>>>>> That's the wrong call. According to what you said earlier you want to
> >>>>>> check for L1 sub-states, not for ASPM in general.
> >>>>>
> >>>>> As per described above, that's why use pcie_aspm_enabled here.
> >>>>>
> >>>>>>
> >>>>>>> + return 0;
> >>>>>>> +
> >>>>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_39)
> >>>>>>> + return 1;
> >>>>>>> +
> >>>>>>> + return 0;
> >>>>>>> +}
> >>>>>>> +
> >>>>>>> static void rtl_wol_shutdown_quirk(struct rtl8169_private *tp)
> >>>>>>> {
> >>>>>>> /* WoL fails with 8168b when the receiver is disabled. */
> >>>>>>> @@ -4991,7 +5004,10 @@ static const struct net_device_ops rtl_netdev_ops = {
> >>>>>>>
> >>>>>>> static void rtl_set_irq_mask(struct rtl8169_private *tp)
> >>>>>>> {
> >>>>>>> - tp->irq_mask = RxOK | RxErr | TxOK | TxErr | LinkChg;
> >>>>>>> + tp->irq_mask = RxOK | RxErr | TxOK | TxErr;
> >>>>>>> +
> >>>>>>> + if (!rtl_phy_poll_quirk(tp))
> >>>>>>> + tp->irq_mask |= LinkChg;
> >>>>>>>
> >>>>>>> if (tp->mac_version <= RTL_GIGA_MAC_VER_06)
> >>>>>>> tp->irq_mask |= SYSErr | RxOverflow | RxFIFOOver;
> >>>>>>> @@ -5085,7 +5101,8 @@ static int r8169_mdio_register(struct rtl8169_private *tp)
> >>>>>>> new_bus->name = "r8169";
> >>>>>>> new_bus->priv = tp;
> >>>>>>> new_bus->parent = &pdev->dev;
> >>>>>>> - new_bus->irq[0] = PHY_MAC_INTERRUPT;
> >>>>>>> + new_bus->irq[0] =
> >>>>>>> + (rtl_phy_poll_quirk(tp) ? PHY_POLL : PHY_MAC_INTERRUPT);
> >>>>>>> snprintf(new_bus->id, MII_BUS_ID_SIZE, "r8169-%x", pci_dev_id(pdev));
> >>>>>>>
> >>>>>>> new_bus->read = r8169_mdio_read_reg;
> >>>>>>>
> >>>>>>
> >>>>
> >>
> >> The r8101 vendor driver applies a special setting for RTL8106e if ASPM is enabled.
> >> Not sure whether it's related but it's worth a try. Could you please check whether
> >> the following makes a difference?
> >
> > After applying this patch, it can't help relieve the issue.
> > The 8101 vendor driver also use polling method to watch the link change event.
> > Tried to disable polling method and enable LinkChg Irq, but it also
> > can't get LinkChg interrupt.
> >
> OK, thanks for testing.
> As it is now, rtl_phy_poll_quirk() would always return false because ASPM
> is disabled on driver load. Changing ASPM settings can be done later via sysfs
> if supported by device and upstream bridge. In addition:

it seems a callback is needed to inform the driver when changing the
aspm policy,
is it correct?

> - If you want to return a bool, declare the return value as bool.
> - You shouldn't have to disable the LinkChg interrupt. The interrupt just triggers
> a phylib state machine run what may result in a faster link-up signal even
> when using polling.

ok.

>
> By the way: All Realtek vendor drivers (r8101, r8168, r8125) don't use the LinkChg
> interrupt. However I don't think this is because of known hw issues, more likely
> it's because they don't use phylib and thought polling is the easier approach.
> At least for r8169 I haven't heard yet of any complain regarding the LinkChg
> interrupt.
>
> >>
> >> diff --git a/drivers/net/ethernet/realtek/r8169_phy_config.c b/drivers/net/ethernet/realtek/r8169_phy_config.c
> >> index 50f0f621b..60014b9c4 100644
> >> --- a/drivers/net/ethernet/realtek/r8169_phy_config.c
> >> +++ b/drivers/net/ethernet/realtek/r8169_phy_config.c
> >> @@ -1153,6 +1153,7 @@ static void rtl8106e_hw_phy_config(struct rtl8169_private *tp,
> >> r8169_apply_firmware(tp);
> >>
> >> rtl_writephy_batch(phydev, phy_reg_init);
> >> + phy_write(phydev, 0x18, 0x8310);
> >> }
> >>
> >> static void rtl8125_legacy_force_mode(struct phy_device *phydev)
> >> --
> >> 2.32.0
> >>
> >>
>

2021-06-09 16:38:36

by Heiner Kallweit

[permalink] [raw]
Subject: Re: [PATCH] [v2] r8169: Use PHY_POLL when RTL8106E enable ASPM

On 09.06.2021 17:23, Koba Ko wrote:
> On Wed, Jun 9, 2021 at 10:29 PM Heiner Kallweit <[email protected]> wrote:
>>
>> On 09.06.2021 03:47, Koba Ko wrote:
>>> On Wed, Jun 9, 2021 at 4:58 AM Heiner Kallweit <[email protected]> wrote:
>>>>
>>>> On 08.06.2021 16:17, Koba Ko wrote:
>>>>> On Tue, Jun 8, 2021 at 9:45 PM Heiner Kallweit <[email protected]> wrote:
>>>>>>
>>>>>> On 08.06.2021 12:43, Koba Ko wrote:
>>>>>>> On Tue, Jun 8, 2021 at 4:00 PM Heiner Kallweit <[email protected]> wrote:
>>>>>>>>
>>>>>>>> On 08.06.2021 05:22, Koba Ko wrote:
>>>>>>>>> For RTL8106E, it's a Fast-ethernet chip.
>>>>>>>>> If ASPM is enabled, the link chang interrupt wouldn't be triggered
>>>>>>>>> immediately and must wait a very long time to get link change interrupt.
>>>>>>>>> Even the link change interrupt isn't triggered, the phy link is already
>>>>>>>>> established.
>>>>>>>>>
>>>>>>>>> Use PHY_POLL to watch the status of phy link and disable
>>>>>>>>> the link change interrupt when ASPM is enabled on RTL8106E.
>>>>>>>>>
>>>>>>>>> v2: Instead use PHY_POLL and identify 8106E by RTL_GIGA_MAC_VER_39.
>>>>>>>>>
>>>>>>>>
>>>>>>>> Still the issue description doesn't convince me that it's a hw bug
>>>>>>>> with the respective chip version. What has been stated so far:
>>>>>>>>
>>>>>>>> 1. (and most important) Issue doesn't occur in mainline because ASPM
>>>>>>>> is disabled in mainline for r8169. Issue occurs only with a
>>>>>>>> downstream kernel with ASPM enabled for r8169.
>>>>>>>
>>>>>>> mainline kernel and enable L1, the issue is also observed.
>>>>>>>
>>>>>> Yes, but enabling L1 via sysfs is at own risk.
>>>>>
>>>>> but we could have a workaround if hw have an aspm issue.
>>>>>
>>>>>>
>>>>>>>> 2. Issue occurs only with ASPM L1.1 not disabled, even though this chip
>>>>>>>> version doesn't support L1 sub-states. Just L0s/L1 don't trigger
>>>>>>>> the issue.
>>>>>>>> The NIC doesn't announce L1.1 support, therefore PCI core won't
>>>>>>>> enable L1 sub-states on the PCIe link between NIC and upstream
>>>>>>>> PCI bridge.
>>>>>>>
>>>>>>> More precisely, when L1 is enabled, the issue would be triggered.
>>>>>>> For RTL8106E,
>>>>>>> 1. Only disable L0s, pcie_aspm_enabled return 1, issue is triggered.
>>>>>>> 2. Only disable L1_1, pcie_aspm_enabled return 1, issue is triggered.
>>>>>>>
>>>>>>> 3. Only disable L1, pcie_aspm_enabled return 0, issue is not triggered.
>>>>>>>
>>>>>>>>
>>>>>>>> 3. Issue occurs only with a GBit-capable link partner. 100MBit link
>>>>>>>> partners are fine. Not clear whether issue occurs with a specific
>>>>>>>> Gbit link partner only or with GBit-capable link partners in general.
>>>>>>>>
>>>>>>>> 4. Only link-up interrupt is affected. Not link-down and not interrupts
>>>>>>>> triggered by other interrupt sources.
>>>>>>>>
>>>>>>>> 5. Realtek couldn't confirm that there's such a hw bug on RTL8106e.
>>>>>>>>
>>>>>>>> One thing that hasn't been asked yet:
>>>>>>>> Does issue occur always if you re-plug the cable? Or only on boot?
>>>>>>>> I'm asking because in the dmesg log you attached to the bugzilla issue
>>>>>>>> the following looks totally ok.
>>>>>>>>
>>>>>>>> [ 61.651643] r8169 0000:01:00.0 enp1s0: Link is Down
>>>>>>>> [ 63.720015] r8169 0000:01:00.0 enp1s0: Link is Up - 100Mbps/Full - flow control rx/tx
>>>>>>>> [ 66.685499] r8169 0000:01:00.0 enp1s0: Link is Down
>>>>>>>
>>>>>>> Once the link is up,
>>>>>>> 1. If cable is unplug&plug immediately, you wouldn't see the issue.
>>>>>>> 2. Unplug cable and wait a long time (~1Mins), then plug the cable,
>>>>>>> the issue appears again.
>>>>>>>
>>>>>> This sounds runtime-pm-related. After 10s the NIC runtime-suspends,
>>>>>> and once the cable is re-plugged a PME is triggered that lets the
>>>>>> PCI core return the PCIe link from D3hot to D0.
>>>>>> If you re-plug the cable after such a longer time, do you see the
>>>>>> PCIe PME immediately in /proc/interrupts?
>>>>>
>>>>> I don't know which irq number is for RTL8106e PME, but check all PME
>>>>> in /proc/interrupt,
>>>>>
>>>>> There's no interrupt increase on all PME entries and rtl8106e irq entry(irq 32).
>>>>>
>>>>>>
>>>>>> And if you set /sys/class/net/<if>/power/control to "on", does the
>>>>>> issue still occur?
>>>>>
>>>>> Yes, after echo "on" to /sys/class/net/<if>/power/control and
>>>>> replugging the cable, the issue is still caught.
>>>>>>
>>>>>>>>
>>>>>>>>> Signed-off-by: Koba Ko <[email protected]>
>>>>>>>>> ---
>>>>>>>>> drivers/net/ethernet/realtek/r8169_main.c | 21 +++++++++++++++++++--
>>>>>>>>> 1 file changed, 19 insertions(+), 2 deletions(-)
>>>>>>>>>
>>>>>>>>> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
>>>>>>>>> index 2c89cde7da1e..a59cbaef2839 100644
>>>>>>>>> --- a/drivers/net/ethernet/realtek/r8169_main.c
>>>>>>>>> +++ b/drivers/net/ethernet/realtek/r8169_main.c
>>>>>>>>> @@ -4914,6 +4914,19 @@ static const struct dev_pm_ops rtl8169_pm_ops = {
>>>>>>>>>
>>>>>>>>> #endif /* CONFIG_PM */
>>>>>>>>>
>>>>>>>>> +static int rtl_phy_poll_quirk(struct rtl8169_private *tp)
>>>>>>>>> +{
>>>>>>>>> + struct pci_dev *pdev = tp->pci_dev;
>>>>>>>>> +
>>>>>>>>> + if (!pcie_aspm_enabled(pdev))
>>>>>>>>
>>>>>>>> That's the wrong call. According to what you said earlier you want to
>>>>>>>> check for L1 sub-states, not for ASPM in general.
>>>>>>>
>>>>>>> As per described above, that's why use pcie_aspm_enabled here.
>>>>>>>
>>>>>>>>
>>>>>>>>> + return 0;
>>>>>>>>> +
>>>>>>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_39)
>>>>>>>>> + return 1;
>>>>>>>>> +
>>>>>>>>> + return 0;
>>>>>>>>> +}
>>>>>>>>> +
>>>>>>>>> static void rtl_wol_shutdown_quirk(struct rtl8169_private *tp)
>>>>>>>>> {
>>>>>>>>> /* WoL fails with 8168b when the receiver is disabled. */
>>>>>>>>> @@ -4991,7 +5004,10 @@ static const struct net_device_ops rtl_netdev_ops = {
>>>>>>>>>
>>>>>>>>> static void rtl_set_irq_mask(struct rtl8169_private *tp)
>>>>>>>>> {
>>>>>>>>> - tp->irq_mask = RxOK | RxErr | TxOK | TxErr | LinkChg;
>>>>>>>>> + tp->irq_mask = RxOK | RxErr | TxOK | TxErr;
>>>>>>>>> +
>>>>>>>>> + if (!rtl_phy_poll_quirk(tp))
>>>>>>>>> + tp->irq_mask |= LinkChg;
>>>>>>>>>
>>>>>>>>> if (tp->mac_version <= RTL_GIGA_MAC_VER_06)
>>>>>>>>> tp->irq_mask |= SYSErr | RxOverflow | RxFIFOOver;
>>>>>>>>> @@ -5085,7 +5101,8 @@ static int r8169_mdio_register(struct rtl8169_private *tp)
>>>>>>>>> new_bus->name = "r8169";
>>>>>>>>> new_bus->priv = tp;
>>>>>>>>> new_bus->parent = &pdev->dev;
>>>>>>>>> - new_bus->irq[0] = PHY_MAC_INTERRUPT;
>>>>>>>>> + new_bus->irq[0] =
>>>>>>>>> + (rtl_phy_poll_quirk(tp) ? PHY_POLL : PHY_MAC_INTERRUPT);
>>>>>>>>> snprintf(new_bus->id, MII_BUS_ID_SIZE, "r8169-%x", pci_dev_id(pdev));
>>>>>>>>>
>>>>>>>>> new_bus->read = r8169_mdio_read_reg;
>>>>>>>>>
>>>>>>>>
>>>>>>
>>>>
>>>> The r8101 vendor driver applies a special setting for RTL8106e if ASPM is enabled.
>>>> Not sure whether it's related but it's worth a try. Could you please check whether
>>>> the following makes a difference?
>>>
>>> After applying this patch, it can't help relieve the issue.
>>> The 8101 vendor driver also use polling method to watch the link change event.
>>> Tried to disable polling method and enable LinkChg Irq, but it also
>>> can't get LinkChg interrupt.
>>>
>> OK, thanks for testing.
>> As it is now, rtl_phy_poll_quirk() would always return false because ASPM
>> is disabled on driver load. Changing ASPM settings can be done later via sysfs
>> if supported by device and upstream bridge. In addition:
>
> it seems a callback is needed to inform the driver when changing the
> aspm policy,
> is it correct?
>
It's not the policy that changes when writing to the link attributes.
See aspm_attr_store_common(), it modifies link->aspm_disable and calls
pcie_config_aspm_link(). Having said that there is no such callback.
All that could be done is switching to polling for this chip version
unconditionally.

One more thing you could try is the following. The PCIe link will
have L1 support enabled, but the NIC won't actively trigger it.
This should be sufficient for the system to reach higher PC package
power saving states.

diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
index b923958af..be162d2f5 100644
--- a/drivers/net/ethernet/realtek/r8169_main.c
+++ b/drivers/net/ethernet/realtek/r8169_main.c
@@ -3510,7 +3510,6 @@ static void rtl_hw_start_8106(struct rtl8169_private *tp)
rtl_eri_write(tp, 0x1b0, ERIAR_MASK_0011, 0x0000);

rtl_pcie_state_l2l3_disable(tp);
- rtl_hw_aspm_clkreq_enable(tp, true);
}

DECLARE_RTL_COND(rtl_mac_ocp_e00e_cond)
--
2.32.0




>> - If you want to return a bool, declare the return value as bool.
>> - You shouldn't have to disable the LinkChg interrupt. The interrupt just triggers
>> a phylib state machine run what may result in a faster link-up signal even
>> when using polling.
>
> ok.
>
>>
>> By the way: All Realtek vendor drivers (r8101, r8168, r8125) don't use the LinkChg
>> interrupt. However I don't think this is because of known hw issues, more likely
>> it's because they don't use phylib and thought polling is the easier approach.
>> At least for r8169 I haven't heard yet of any complain regarding the LinkChg
>> interrupt.
>>
>>>>
>>>> diff --git a/drivers/net/ethernet/realtek/r8169_phy_config.c b/drivers/net/ethernet/realtek/r8169_phy_config.c
>>>> index 50f0f621b..60014b9c4 100644
>>>> --- a/drivers/net/ethernet/realtek/r8169_phy_config.c
>>>> +++ b/drivers/net/ethernet/realtek/r8169_phy_config.c
>>>> @@ -1153,6 +1153,7 @@ static void rtl8106e_hw_phy_config(struct rtl8169_private *tp,
>>>> r8169_apply_firmware(tp);
>>>>
>>>> rtl_writephy_batch(phydev, phy_reg_init);
>>>> + phy_write(phydev, 0x18, 0x8310);
>>>> }
>>>>
>>>> static void rtl8125_legacy_force_mode(struct phy_device *phydev)
>>>> --
>>>> 2.32.0
>>>>
>>>>
>>

2021-06-09 17:04:38

by Koba Ko

[permalink] [raw]
Subject: Re: [PATCH] [v2] r8169: Use PHY_POLL when RTL8106E enable ASPM

On Wed, Jun 9, 2021 at 4:58 AM Heiner Kallweit <[email protected]> wrote:
>
> On 08.06.2021 16:17, Koba Ko wrote:
> > On Tue, Jun 8, 2021 at 9:45 PM Heiner Kallweit <[email protected]> wrote:
> >>
> >> On 08.06.2021 12:43, Koba Ko wrote:
> >>> On Tue, Jun 8, 2021 at 4:00 PM Heiner Kallweit <[email protected]> wrote:
> >>>>
> >>>> On 08.06.2021 05:22, Koba Ko wrote:
> >>>>> For RTL8106E, it's a Fast-ethernet chip.
> >>>>> If ASPM is enabled, the link chang interrupt wouldn't be triggered
> >>>>> immediately and must wait a very long time to get link change interrupt.
> >>>>> Even the link change interrupt isn't triggered, the phy link is already
> >>>>> established.
> >>>>>
> >>>>> Use PHY_POLL to watch the status of phy link and disable
> >>>>> the link change interrupt when ASPM is enabled on RTL8106E.
> >>>>>
> >>>>> v2: Instead use PHY_POLL and identify 8106E by RTL_GIGA_MAC_VER_39.
> >>>>>
> >>>>
> >>>> Still the issue description doesn't convince me that it's a hw bug
> >>>> with the respective chip version. What has been stated so far:
> >>>>
> >>>> 1. (and most important) Issue doesn't occur in mainline because ASPM
> >>>> is disabled in mainline for r8169. Issue occurs only with a
> >>>> downstream kernel with ASPM enabled for r8169.
> >>>
> >>> mainline kernel and enable L1, the issue is also observed.
> >>>
> >> Yes, but enabling L1 via sysfs is at own risk.
> >
> > but we could have a workaround if hw have an aspm issue.
> >
> >>
> >>>> 2. Issue occurs only with ASPM L1.1 not disabled, even though this chip
> >>>> version doesn't support L1 sub-states. Just L0s/L1 don't trigger
> >>>> the issue.
> >>>> The NIC doesn't announce L1.1 support, therefore PCI core won't
> >>>> enable L1 sub-states on the PCIe link between NIC and upstream
> >>>> PCI bridge.
> >>>
> >>> More precisely, when L1 is enabled, the issue would be triggered.
> >>> For RTL8106E,
> >>> 1. Only disable L0s, pcie_aspm_enabled return 1, issue is triggered.
> >>> 2. Only disable L1_1, pcie_aspm_enabled return 1, issue is triggered.
> >>>
> >>> 3. Only disable L1, pcie_aspm_enabled return 0, issue is not triggered.
> >>>
> >>>>
> >>>> 3. Issue occurs only with a GBit-capable link partner. 100MBit link
> >>>> partners are fine. Not clear whether issue occurs with a specific
> >>>> Gbit link partner only or with GBit-capable link partners in general.
> >>>>
> >>>> 4. Only link-up interrupt is affected. Not link-down and not interrupts
> >>>> triggered by other interrupt sources.
> >>>>
> >>>> 5. Realtek couldn't confirm that there's such a hw bug on RTL8106e.
> >>>>
> >>>> One thing that hasn't been asked yet:
> >>>> Does issue occur always if you re-plug the cable? Or only on boot?
> >>>> I'm asking because in the dmesg log you attached to the bugzilla issue
> >>>> the following looks totally ok.
> >>>>
> >>>> [ 61.651643] r8169 0000:01:00.0 enp1s0: Link is Down
> >>>> [ 63.720015] r8169 0000:01:00.0 enp1s0: Link is Up - 100Mbps/Full - flow control rx/tx
> >>>> [ 66.685499] r8169 0000:01:00.0 enp1s0: Link is Down
> >>>
> >>> Once the link is up,
> >>> 1. If cable is unplug&plug immediately, you wouldn't see the issue.
> >>> 2. Unplug cable and wait a long time (~1Mins), then plug the cable,
> >>> the issue appears again.
> >>>
> >> This sounds runtime-pm-related. After 10s the NIC runtime-suspends,
> >> and once the cable is re-plugged a PME is triggered that lets the
> >> PCI core return the PCIe link from D3hot to D0.
> >> If you re-plug the cable after such a longer time, do you see the
> >> PCIe PME immediately in /proc/interrupts?
> >
> > I don't know which irq number is for RTL8106e PME, but check all PME
> > in /proc/interrupt,
> >
> > There's no interrupt increase on all PME entries and rtl8106e irq entry(irq 32).
> >
> >>
> >> And if you set /sys/class/net/<if>/power/control to "on", does the
> >> issue still occur?
> >
> > Yes, after echo "on" to /sys/class/net/<if>/power/control and
> > replugging the cable, the issue is still caught.
> >>
> >>>>
> >>>>> Signed-off-by: Koba Ko <[email protected]>
> >>>>> ---
> >>>>> drivers/net/ethernet/realtek/r8169_main.c | 21 +++++++++++++++++++--
> >>>>> 1 file changed, 19 insertions(+), 2 deletions(-)
> >>>>>
> >>>>> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
> >>>>> index 2c89cde7da1e..a59cbaef2839 100644
> >>>>> --- a/drivers/net/ethernet/realtek/r8169_main.c
> >>>>> +++ b/drivers/net/ethernet/realtek/r8169_main.c
> >>>>> @@ -4914,6 +4914,19 @@ static const struct dev_pm_ops rtl8169_pm_ops = {
> >>>>>
> >>>>> #endif /* CONFIG_PM */
> >>>>>
> >>>>> +static int rtl_phy_poll_quirk(struct rtl8169_private *tp)
> >>>>> +{
> >>>>> + struct pci_dev *pdev = tp->pci_dev;
> >>>>> +
> >>>>> + if (!pcie_aspm_enabled(pdev))
> >>>>
> >>>> That's the wrong call. According to what you said earlier you want to
> >>>> check for L1 sub-states, not for ASPM in general.
> >>>
> >>> As per described above, that's why use pcie_aspm_enabled here.
> >>>
> >>>>
> >>>>> + return 0;
> >>>>> +
> >>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_39)
> >>>>> + return 1;
> >>>>> +
> >>>>> + return 0;
> >>>>> +}
> >>>>> +
> >>>>> static void rtl_wol_shutdown_quirk(struct rtl8169_private *tp)
> >>>>> {
> >>>>> /* WoL fails with 8168b when the receiver is disabled. */
> >>>>> @@ -4991,7 +5004,10 @@ static const struct net_device_ops rtl_netdev_ops = {
> >>>>>
> >>>>> static void rtl_set_irq_mask(struct rtl8169_private *tp)
> >>>>> {
> >>>>> - tp->irq_mask = RxOK | RxErr | TxOK | TxErr | LinkChg;
> >>>>> + tp->irq_mask = RxOK | RxErr | TxOK | TxErr;
> >>>>> +
> >>>>> + if (!rtl_phy_poll_quirk(tp))
> >>>>> + tp->irq_mask |= LinkChg;
> >>>>>
> >>>>> if (tp->mac_version <= RTL_GIGA_MAC_VER_06)
> >>>>> tp->irq_mask |= SYSErr | RxOverflow | RxFIFOOver;
> >>>>> @@ -5085,7 +5101,8 @@ static int r8169_mdio_register(struct rtl8169_private *tp)
> >>>>> new_bus->name = "r8169";
> >>>>> new_bus->priv = tp;
> >>>>> new_bus->parent = &pdev->dev;
> >>>>> - new_bus->irq[0] = PHY_MAC_INTERRUPT;
> >>>>> + new_bus->irq[0] =
> >>>>> + (rtl_phy_poll_quirk(tp) ? PHY_POLL : PHY_MAC_INTERRUPT);
> >>>>> snprintf(new_bus->id, MII_BUS_ID_SIZE, "r8169-%x", pci_dev_id(pdev));
> >>>>>
> >>>>> new_bus->read = r8169_mdio_read_reg;
> >>>>>
> >>>>
> >>
>
> The r8101 vendor driver applies a special setting for RTL8106e if ASPM is enabled.
> Not sure whether it's related but it's worth a try. Could you please check whether
> the following makes a difference?

After applying this patch, it can't help relieve the issue.
The 8101 vendor driver also use polling method to watch the link change event.
Tried to disable polling method and enable LinkChg Irq, but it also
can't get LinkChg interrupt.

>
> diff --git a/drivers/net/ethernet/realtek/r8169_phy_config.c b/drivers/net/ethernet/realtek/r8169_phy_config.c
> index 50f0f621b..60014b9c4 100644
> --- a/drivers/net/ethernet/realtek/r8169_phy_config.c
> +++ b/drivers/net/ethernet/realtek/r8169_phy_config.c
> @@ -1153,6 +1153,7 @@ static void rtl8106e_hw_phy_config(struct rtl8169_private *tp,
> r8169_apply_firmware(tp);
>
> rtl_writephy_batch(phydev, phy_reg_init);
> + phy_write(phydev, 0x18, 0x8310);
> }
>
> static void rtl8125_legacy_force_mode(struct phy_device *phydev)
> --
> 2.32.0
>
>

2021-06-10 05:12:39

by Koba Ko

[permalink] [raw]
Subject: Re: [PATCH] [v2] r8169: Use PHY_POLL when RTL8106E enable ASPM

On Thu, Jun 10, 2021 at 12:12 AM Heiner Kallweit <[email protected]> wrote:
>
> On 09.06.2021 17:23, Koba Ko wrote:
> > On Wed, Jun 9, 2021 at 10:29 PM Heiner Kallweit <[email protected]> wrote:
> >>
> >> On 09.06.2021 03:47, Koba Ko wrote:
> >>> On Wed, Jun 9, 2021 at 4:58 AM Heiner Kallweit <[email protected]> wrote:
> >>>>
> >>>> On 08.06.2021 16:17, Koba Ko wrote:
> >>>>> On Tue, Jun 8, 2021 at 9:45 PM Heiner Kallweit <[email protected]> wrote:
> >>>>>>
> >>>>>> On 08.06.2021 12:43, Koba Ko wrote:
> >>>>>>> On Tue, Jun 8, 2021 at 4:00 PM Heiner Kallweit <[email protected]> wrote:
> >>>>>>>>
> >>>>>>>> On 08.06.2021 05:22, Koba Ko wrote:
> >>>>>>>>> For RTL8106E, it's a Fast-ethernet chip.
> >>>>>>>>> If ASPM is enabled, the link chang interrupt wouldn't be triggered
> >>>>>>>>> immediately and must wait a very long time to get link change interrupt.
> >>>>>>>>> Even the link change interrupt isn't triggered, the phy link is already
> >>>>>>>>> established.
> >>>>>>>>>
> >>>>>>>>> Use PHY_POLL to watch the status of phy link and disable
> >>>>>>>>> the link change interrupt when ASPM is enabled on RTL8106E.
> >>>>>>>>>
> >>>>>>>>> v2: Instead use PHY_POLL and identify 8106E by RTL_GIGA_MAC_VER_39.
> >>>>>>>>>
> >>>>>>>>
> >>>>>>>> Still the issue description doesn't convince me that it's a hw bug
> >>>>>>>> with the respective chip version. What has been stated so far:
> >>>>>>>>
> >>>>>>>> 1. (and most important) Issue doesn't occur in mainline because ASPM
> >>>>>>>> is disabled in mainline for r8169. Issue occurs only with a
> >>>>>>>> downstream kernel with ASPM enabled for r8169.
> >>>>>>>
> >>>>>>> mainline kernel and enable L1, the issue is also observed.
> >>>>>>>
> >>>>>> Yes, but enabling L1 via sysfs is at own risk.
> >>>>>
> >>>>> but we could have a workaround if hw have an aspm issue.
> >>>>>
> >>>>>>
> >>>>>>>> 2. Issue occurs only with ASPM L1.1 not disabled, even though this chip
> >>>>>>>> version doesn't support L1 sub-states. Just L0s/L1 don't trigger
> >>>>>>>> the issue.
> >>>>>>>> The NIC doesn't announce L1.1 support, therefore PCI core won't
> >>>>>>>> enable L1 sub-states on the PCIe link between NIC and upstream
> >>>>>>>> PCI bridge.
> >>>>>>>
> >>>>>>> More precisely, when L1 is enabled, the issue would be triggered.
> >>>>>>> For RTL8106E,
> >>>>>>> 1. Only disable L0s, pcie_aspm_enabled return 1, issue is triggered.
> >>>>>>> 2. Only disable L1_1, pcie_aspm_enabled return 1, issue is triggered.
> >>>>>>>
> >>>>>>> 3. Only disable L1, pcie_aspm_enabled return 0, issue is not triggered.
> >>>>>>>
> >>>>>>>>
> >>>>>>>> 3. Issue occurs only with a GBit-capable link partner. 100MBit link
> >>>>>>>> partners are fine. Not clear whether issue occurs with a specific
> >>>>>>>> Gbit link partner only or with GBit-capable link partners in general.
> >>>>>>>>
> >>>>>>>> 4. Only link-up interrupt is affected. Not link-down and not interrupts
> >>>>>>>> triggered by other interrupt sources.
> >>>>>>>>
> >>>>>>>> 5. Realtek couldn't confirm that there's such a hw bug on RTL8106e.
> >>>>>>>>
> >>>>>>>> One thing that hasn't been asked yet:
> >>>>>>>> Does issue occur always if you re-plug the cable? Or only on boot?
> >>>>>>>> I'm asking because in the dmesg log you attached to the bugzilla issue
> >>>>>>>> the following looks totally ok.
> >>>>>>>>
> >>>>>>>> [ 61.651643] r8169 0000:01:00.0 enp1s0: Link is Down
> >>>>>>>> [ 63.720015] r8169 0000:01:00.0 enp1s0: Link is Up - 100Mbps/Full - flow control rx/tx
> >>>>>>>> [ 66.685499] r8169 0000:01:00.0 enp1s0: Link is Down
> >>>>>>>
> >>>>>>> Once the link is up,
> >>>>>>> 1. If cable is unplug&plug immediately, you wouldn't see the issue.
> >>>>>>> 2. Unplug cable and wait a long time (~1Mins), then plug the cable,
> >>>>>>> the issue appears again.
> >>>>>>>
> >>>>>> This sounds runtime-pm-related. After 10s the NIC runtime-suspends,
> >>>>>> and once the cable is re-plugged a PME is triggered that lets the
> >>>>>> PCI core return the PCIe link from D3hot to D0.
> >>>>>> If you re-plug the cable after such a longer time, do you see the
> >>>>>> PCIe PME immediately in /proc/interrupts?
> >>>>>
> >>>>> I don't know which irq number is for RTL8106e PME, but check all PME
> >>>>> in /proc/interrupt,
> >>>>>
> >>>>> There's no interrupt increase on all PME entries and rtl8106e irq entry(irq 32).
> >>>>>
> >>>>>>
> >>>>>> And if you set /sys/class/net/<if>/power/control to "on", does the
> >>>>>> issue still occur?
> >>>>>
> >>>>> Yes, after echo "on" to /sys/class/net/<if>/power/control and
> >>>>> replugging the cable, the issue is still caught.
> >>>>>>
> >>>>>>>>
> >>>>>>>>> Signed-off-by: Koba Ko <[email protected]>
> >>>>>>>>> ---
> >>>>>>>>> drivers/net/ethernet/realtek/r8169_main.c | 21 +++++++++++++++++++--
> >>>>>>>>> 1 file changed, 19 insertions(+), 2 deletions(-)
> >>>>>>>>>
> >>>>>>>>> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
> >>>>>>>>> index 2c89cde7da1e..a59cbaef2839 100644
> >>>>>>>>> --- a/drivers/net/ethernet/realtek/r8169_main.c
> >>>>>>>>> +++ b/drivers/net/ethernet/realtek/r8169_main.c
> >>>>>>>>> @@ -4914,6 +4914,19 @@ static const struct dev_pm_ops rtl8169_pm_ops = {
> >>>>>>>>>
> >>>>>>>>> #endif /* CONFIG_PM */
> >>>>>>>>>
> >>>>>>>>> +static int rtl_phy_poll_quirk(struct rtl8169_private *tp)
> >>>>>>>>> +{
> >>>>>>>>> + struct pci_dev *pdev = tp->pci_dev;
> >>>>>>>>> +
> >>>>>>>>> + if (!pcie_aspm_enabled(pdev))
> >>>>>>>>
> >>>>>>>> That's the wrong call. According to what you said earlier you want to
> >>>>>>>> check for L1 sub-states, not for ASPM in general.
> >>>>>>>
> >>>>>>> As per described above, that's why use pcie_aspm_enabled here.
> >>>>>>>
> >>>>>>>>
> >>>>>>>>> + return 0;
> >>>>>>>>> +
> >>>>>>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_39)
> >>>>>>>>> + return 1;
> >>>>>>>>> +
> >>>>>>>>> + return 0;
> >>>>>>>>> +}
> >>>>>>>>> +
> >>>>>>>>> static void rtl_wol_shutdown_quirk(struct rtl8169_private *tp)
> >>>>>>>>> {
> >>>>>>>>> /* WoL fails with 8168b when the receiver is disabled. */
> >>>>>>>>> @@ -4991,7 +5004,10 @@ static const struct net_device_ops rtl_netdev_ops = {
> >>>>>>>>>
> >>>>>>>>> static void rtl_set_irq_mask(struct rtl8169_private *tp)
> >>>>>>>>> {
> >>>>>>>>> - tp->irq_mask = RxOK | RxErr | TxOK | TxErr | LinkChg;
> >>>>>>>>> + tp->irq_mask = RxOK | RxErr | TxOK | TxErr;
> >>>>>>>>> +
> >>>>>>>>> + if (!rtl_phy_poll_quirk(tp))
> >>>>>>>>> + tp->irq_mask |= LinkChg;
> >>>>>>>>>
> >>>>>>>>> if (tp->mac_version <= RTL_GIGA_MAC_VER_06)
> >>>>>>>>> tp->irq_mask |= SYSErr | RxOverflow | RxFIFOOver;
> >>>>>>>>> @@ -5085,7 +5101,8 @@ static int r8169_mdio_register(struct rtl8169_private *tp)
> >>>>>>>>> new_bus->name = "r8169";
> >>>>>>>>> new_bus->priv = tp;
> >>>>>>>>> new_bus->parent = &pdev->dev;
> >>>>>>>>> - new_bus->irq[0] = PHY_MAC_INTERRUPT;
> >>>>>>>>> + new_bus->irq[0] =
> >>>>>>>>> + (rtl_phy_poll_quirk(tp) ? PHY_POLL : PHY_MAC_INTERRUPT);
> >>>>>>>>> snprintf(new_bus->id, MII_BUS_ID_SIZE, "r8169-%x", pci_dev_id(pdev));
> >>>>>>>>>
> >>>>>>>>> new_bus->read = r8169_mdio_read_reg;
> >>>>>>>>>
> >>>>>>>>
> >>>>>>
> >>>>
> >>>> The r8101 vendor driver applies a special setting for RTL8106e if ASPM is enabled.
> >>>> Not sure whether it's related but it's worth a try. Could you please check whether
> >>>> the following makes a difference?
> >>>
> >>> After applying this patch, it can't help relieve the issue.
> >>> The 8101 vendor driver also use polling method to watch the link change event.
> >>> Tried to disable polling method and enable LinkChg Irq, but it also
> >>> can't get LinkChg interrupt.
> >>>
> >> OK, thanks for testing.
> >> As it is now, rtl_phy_poll_quirk() would always return false because ASPM
> >> is disabled on driver load. Changing ASPM settings can be done later via sysfs
> >> if supported by device and upstream bridge. In addition:
> >
> > it seems a callback is needed to inform the driver when changing the
> > aspm policy,
> > is it correct?
> >
> It's not the policy that changes when writing to the link attributes.
> See aspm_attr_store_common(), it modifies link->aspm_disable and calls
> pcie_config_aspm_link(). Having said that there is no such callback.
> All that could be done is switching to polling for this chip version
> unconditionally.
>
> One more thing you could try is the following. The PCIe link will
> have L1 support enabled, but the NIC won't actively trigger it.
> This should be sufficient for the system to reach higher PC package
> power saving states.

After applying this patch, the issue can't be got.
I also tried to call rtl_hw_aspm_clkreq_enable(tp, false); on
rtl8169h/8111h on intel platform.
the machine could go deeper to pc10.
After tried this patch, I still think there's a hw issue on ASPM for rtl8106e.
How do you think which next step is better?

Im very appreciate your effort.
Thanks

>
> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
> index b923958af..be162d2f5 100644
> --- a/drivers/net/ethernet/realtek/r8169_main.c
> +++ b/drivers/net/ethernet/realtek/r8169_main.c
> @@ -3510,7 +3510,6 @@ static void rtl_hw_start_8106(struct rtl8169_private *tp)
> rtl_eri_write(tp, 0x1b0, ERIAR_MASK_0011, 0x0000);
>
> rtl_pcie_state_l2l3_disable(tp);
> - rtl_hw_aspm_clkreq_enable(tp, true);
> }
>
> DECLARE_RTL_COND(rtl_mac_ocp_e00e_cond)
> --
> 2.32.0
>
>
>
>
> >> - If you want to return a bool, declare the return value as bool.
> >> - You shouldn't have to disable the LinkChg interrupt. The interrupt just triggers
> >> a phylib state machine run what may result in a faster link-up signal even
> >> when using polling.
> >
> > ok.
> >
> >>
> >> By the way: All Realtek vendor drivers (r8101, r8168, r8125) don't use the LinkChg
> >> interrupt. However I don't think this is because of known hw issues, more likely
> >> it's because they don't use phylib and thought polling is the easier approach.
> >> At least for r8169 I haven't heard yet of any complain regarding the LinkChg
> >> interrupt.
> >>
> >>>>
> >>>> diff --git a/drivers/net/ethernet/realtek/r8169_phy_config.c b/drivers/net/ethernet/realtek/r8169_phy_config.c
> >>>> index 50f0f621b..60014b9c4 100644
> >>>> --- a/drivers/net/ethernet/realtek/r8169_phy_config.c
> >>>> +++ b/drivers/net/ethernet/realtek/r8169_phy_config.c
> >>>> @@ -1153,6 +1153,7 @@ static void rtl8106e_hw_phy_config(struct rtl8169_private *tp,
> >>>> r8169_apply_firmware(tp);
> >>>>
> >>>> rtl_writephy_batch(phydev, phy_reg_init);
> >>>> + phy_write(phydev, 0x18, 0x8310);
> >>>> }
> >>>>
> >>>> static void rtl8125_legacy_force_mode(struct phy_device *phydev)
> >>>> --
> >>>> 2.32.0
> >>>>
> >>>>
> >>
>

2021-06-10 10:13:09

by Heiner Kallweit

[permalink] [raw]
Subject: Re: [PATCH] [v2] r8169: Use PHY_POLL when RTL8106E enable ASPM

On 10.06.2021 07:09, Koba Ko wrote:
> On Thu, Jun 10, 2021 at 12:12 AM Heiner Kallweit <[email protected]> wrote:
>>
>> On 09.06.2021 17:23, Koba Ko wrote:
>>> On Wed, Jun 9, 2021 at 10:29 PM Heiner Kallweit <[email protected]> wrote:
>>>>
>>>> On 09.06.2021 03:47, Koba Ko wrote:
>>>>> On Wed, Jun 9, 2021 at 4:58 AM Heiner Kallweit <[email protected]> wrote:
>>>>>>
>>>>>> On 08.06.2021 16:17, Koba Ko wrote:
>>>>>>> On Tue, Jun 8, 2021 at 9:45 PM Heiner Kallweit <[email protected]> wrote:
>>>>>>>>
>>>>>>>> On 08.06.2021 12:43, Koba Ko wrote:
>>>>>>>>> On Tue, Jun 8, 2021 at 4:00 PM Heiner Kallweit <[email protected]> wrote:
>>>>>>>>>>
>>>>>>>>>> On 08.06.2021 05:22, Koba Ko wrote:
>>>>>>>>>>> For RTL8106E, it's a Fast-ethernet chip.
>>>>>>>>>>> If ASPM is enabled, the link chang interrupt wouldn't be triggered
>>>>>>>>>>> immediately and must wait a very long time to get link change interrupt.
>>>>>>>>>>> Even the link change interrupt isn't triggered, the phy link is already
>>>>>>>>>>> established.
>>>>>>>>>>>
>>>>>>>>>>> Use PHY_POLL to watch the status of phy link and disable
>>>>>>>>>>> the link change interrupt when ASPM is enabled on RTL8106E.
>>>>>>>>>>>
>>>>>>>>>>> v2: Instead use PHY_POLL and identify 8106E by RTL_GIGA_MAC_VER_39.
>>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> Still the issue description doesn't convince me that it's a hw bug
>>>>>>>>>> with the respective chip version. What has been stated so far:
>>>>>>>>>>
>>>>>>>>>> 1. (and most important) Issue doesn't occur in mainline because ASPM
>>>>>>>>>> is disabled in mainline for r8169. Issue occurs only with a
>>>>>>>>>> downstream kernel with ASPM enabled for r8169.
>>>>>>>>>
>>>>>>>>> mainline kernel and enable L1, the issue is also observed.
>>>>>>>>>
>>>>>>>> Yes, but enabling L1 via sysfs is at own risk.
>>>>>>>
>>>>>>> but we could have a workaround if hw have an aspm issue.
>>>>>>>
>>>>>>>>
>>>>>>>>>> 2. Issue occurs only with ASPM L1.1 not disabled, even though this chip
>>>>>>>>>> version doesn't support L1 sub-states. Just L0s/L1 don't trigger
>>>>>>>>>> the issue.
>>>>>>>>>> The NIC doesn't announce L1.1 support, therefore PCI core won't
>>>>>>>>>> enable L1 sub-states on the PCIe link between NIC and upstream
>>>>>>>>>> PCI bridge.
>>>>>>>>>
>>>>>>>>> More precisely, when L1 is enabled, the issue would be triggered.
>>>>>>>>> For RTL8106E,
>>>>>>>>> 1. Only disable L0s, pcie_aspm_enabled return 1, issue is triggered.
>>>>>>>>> 2. Only disable L1_1, pcie_aspm_enabled return 1, issue is triggered.
>>>>>>>>>
>>>>>>>>> 3. Only disable L1, pcie_aspm_enabled return 0, issue is not triggered.
>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> 3. Issue occurs only with a GBit-capable link partner. 100MBit link
>>>>>>>>>> partners are fine. Not clear whether issue occurs with a specific
>>>>>>>>>> Gbit link partner only or with GBit-capable link partners in general.
>>>>>>>>>>
>>>>>>>>>> 4. Only link-up interrupt is affected. Not link-down and not interrupts
>>>>>>>>>> triggered by other interrupt sources.
>>>>>>>>>>
>>>>>>>>>> 5. Realtek couldn't confirm that there's such a hw bug on RTL8106e.
>>>>>>>>>>
>>>>>>>>>> One thing that hasn't been asked yet:
>>>>>>>>>> Does issue occur always if you re-plug the cable? Or only on boot?
>>>>>>>>>> I'm asking because in the dmesg log you attached to the bugzilla issue
>>>>>>>>>> the following looks totally ok.
>>>>>>>>>>
>>>>>>>>>> [ 61.651643] r8169 0000:01:00.0 enp1s0: Link is Down
>>>>>>>>>> [ 63.720015] r8169 0000:01:00.0 enp1s0: Link is Up - 100Mbps/Full - flow control rx/tx
>>>>>>>>>> [ 66.685499] r8169 0000:01:00.0 enp1s0: Link is Down
>>>>>>>>>
>>>>>>>>> Once the link is up,
>>>>>>>>> 1. If cable is unplug&plug immediately, you wouldn't see the issue.
>>>>>>>>> 2. Unplug cable and wait a long time (~1Mins), then plug the cable,
>>>>>>>>> the issue appears again.
>>>>>>>>>
>>>>>>>> This sounds runtime-pm-related. After 10s the NIC runtime-suspends,
>>>>>>>> and once the cable is re-plugged a PME is triggered that lets the
>>>>>>>> PCI core return the PCIe link from D3hot to D0.
>>>>>>>> If you re-plug the cable after such a longer time, do you see the
>>>>>>>> PCIe PME immediately in /proc/interrupts?
>>>>>>>
>>>>>>> I don't know which irq number is for RTL8106e PME, but check all PME
>>>>>>> in /proc/interrupt,
>>>>>>>
>>>>>>> There's no interrupt increase on all PME entries and rtl8106e irq entry(irq 32).
>>>>>>>
>>>>>>>>
>>>>>>>> And if you set /sys/class/net/<if>/power/control to "on", does the
>>>>>>>> issue still occur?
>>>>>>>
>>>>>>> Yes, after echo "on" to /sys/class/net/<if>/power/control and
>>>>>>> replugging the cable, the issue is still caught.
>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>> Signed-off-by: Koba Ko <[email protected]>
>>>>>>>>>>> ---
>>>>>>>>>>> drivers/net/ethernet/realtek/r8169_main.c | 21 +++++++++++++++++++--
>>>>>>>>>>> 1 file changed, 19 insertions(+), 2 deletions(-)
>>>>>>>>>>>
>>>>>>>>>>> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
>>>>>>>>>>> index 2c89cde7da1e..a59cbaef2839 100644
>>>>>>>>>>> --- a/drivers/net/ethernet/realtek/r8169_main.c
>>>>>>>>>>> +++ b/drivers/net/ethernet/realtek/r8169_main.c
>>>>>>>>>>> @@ -4914,6 +4914,19 @@ static const struct dev_pm_ops rtl8169_pm_ops = {
>>>>>>>>>>>
>>>>>>>>>>> #endif /* CONFIG_PM */
>>>>>>>>>>>
>>>>>>>>>>> +static int rtl_phy_poll_quirk(struct rtl8169_private *tp)
>>>>>>>>>>> +{
>>>>>>>>>>> + struct pci_dev *pdev = tp->pci_dev;
>>>>>>>>>>> +
>>>>>>>>>>> + if (!pcie_aspm_enabled(pdev))
>>>>>>>>>>
>>>>>>>>>> That's the wrong call. According to what you said earlier you want to
>>>>>>>>>> check for L1 sub-states, not for ASPM in general.
>>>>>>>>>
>>>>>>>>> As per described above, that's why use pcie_aspm_enabled here.
>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>> + return 0;
>>>>>>>>>>> +
>>>>>>>>>>> + if (tp->mac_version == RTL_GIGA_MAC_VER_39)
>>>>>>>>>>> + return 1;
>>>>>>>>>>> +
>>>>>>>>>>> + return 0;
>>>>>>>>>>> +}
>>>>>>>>>>> +
>>>>>>>>>>> static void rtl_wol_shutdown_quirk(struct rtl8169_private *tp)
>>>>>>>>>>> {
>>>>>>>>>>> /* WoL fails with 8168b when the receiver is disabled. */
>>>>>>>>>>> @@ -4991,7 +5004,10 @@ static const struct net_device_ops rtl_netdev_ops = {
>>>>>>>>>>>
>>>>>>>>>>> static void rtl_set_irq_mask(struct rtl8169_private *tp)
>>>>>>>>>>> {
>>>>>>>>>>> - tp->irq_mask = RxOK | RxErr | TxOK | TxErr | LinkChg;
>>>>>>>>>>> + tp->irq_mask = RxOK | RxErr | TxOK | TxErr;
>>>>>>>>>>> +
>>>>>>>>>>> + if (!rtl_phy_poll_quirk(tp))
>>>>>>>>>>> + tp->irq_mask |= LinkChg;
>>>>>>>>>>>
>>>>>>>>>>> if (tp->mac_version <= RTL_GIGA_MAC_VER_06)
>>>>>>>>>>> tp->irq_mask |= SYSErr | RxOverflow | RxFIFOOver;
>>>>>>>>>>> @@ -5085,7 +5101,8 @@ static int r8169_mdio_register(struct rtl8169_private *tp)
>>>>>>>>>>> new_bus->name = "r8169";
>>>>>>>>>>> new_bus->priv = tp;
>>>>>>>>>>> new_bus->parent = &pdev->dev;
>>>>>>>>>>> - new_bus->irq[0] = PHY_MAC_INTERRUPT;
>>>>>>>>>>> + new_bus->irq[0] =
>>>>>>>>>>> + (rtl_phy_poll_quirk(tp) ? PHY_POLL : PHY_MAC_INTERRUPT);
>>>>>>>>>>> snprintf(new_bus->id, MII_BUS_ID_SIZE, "r8169-%x", pci_dev_id(pdev));
>>>>>>>>>>>
>>>>>>>>>>> new_bus->read = r8169_mdio_read_reg;
>>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>
>>>>>>
>>>>>> The r8101 vendor driver applies a special setting for RTL8106e if ASPM is enabled.
>>>>>> Not sure whether it's related but it's worth a try. Could you please check whether
>>>>>> the following makes a difference?
>>>>>
>>>>> After applying this patch, it can't help relieve the issue.
>>>>> The 8101 vendor driver also use polling method to watch the link change event.
>>>>> Tried to disable polling method and enable LinkChg Irq, but it also
>>>>> can't get LinkChg interrupt.
>>>>>
>>>> OK, thanks for testing.
>>>> As it is now, rtl_phy_poll_quirk() would always return false because ASPM
>>>> is disabled on driver load. Changing ASPM settings can be done later via sysfs
>>>> if supported by device and upstream bridge. In addition:
>>>
>>> it seems a callback is needed to inform the driver when changing the
>>> aspm policy,
>>> is it correct?
>>>
>> It's not the policy that changes when writing to the link attributes.
>> See aspm_attr_store_common(), it modifies link->aspm_disable and calls
>> pcie_config_aspm_link(). Having said that there is no such callback.
>> All that could be done is switching to polling for this chip version
>> unconditionally.
>>
>> One more thing you could try is the following. The PCIe link will
>> have L1 support enabled, but the NIC won't actively trigger it.
>> This should be sufficient for the system to reach higher PC package
>> power saving states.
>
> After applying this patch, the issue can't be got.
> I also tried to call rtl_hw_aspm_clkreq_enable(tp, false); on
> rtl8169h/8111h on intel platform.
> the machine could go deeper to pc10.

You mean with the current rtl_hw_aspm_clkreq_enable(tp, true) you reach
only a lower pc state with RTL8168h?
Unfortunately Realtek doesn't release datasheets, therefore I don't
know the exact function of the affected registers/bits.


> After tried this patch, I still think there's a hw issue on ASPM for rtl8106e.
> How do you think which next step is better?
>
> Im very appreciate your effort.
> Thanks
>
>>
>> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
>> index b923958af..be162d2f5 100644
>> --- a/drivers/net/ethernet/realtek/r8169_main.c
>> +++ b/drivers/net/ethernet/realtek/r8169_main.c
>> @@ -3510,7 +3510,6 @@ static void rtl_hw_start_8106(struct rtl8169_private *tp)
>> rtl_eri_write(tp, 0x1b0, ERIAR_MASK_0011, 0x0000);
>>
>> rtl_pcie_state_l2l3_disable(tp);
>> - rtl_hw_aspm_clkreq_enable(tp, true);
>> }
>>
>> DECLARE_RTL_COND(rtl_mac_ocp_e00e_cond)
>> --
>> 2.32.0
>>
>>
>>
>>
>>>> - If you want to return a bool, declare the return value as bool.
>>>> - You shouldn't have to disable the LinkChg interrupt. The interrupt just triggers
>>>> a phylib state machine run what may result in a faster link-up signal even
>>>> when using polling.
>>>
>>> ok.
>>>
>>>>
>>>> By the way: All Realtek vendor drivers (r8101, r8168, r8125) don't use the LinkChg
>>>> interrupt. However I don't think this is because of known hw issues, more likely
>>>> it's because they don't use phylib and thought polling is the easier approach.
>>>> At least for r8169 I haven't heard yet of any complain regarding the LinkChg
>>>> interrupt.
>>>>
>>>>>>
>>>>>> diff --git a/drivers/net/ethernet/realtek/r8169_phy_config.c b/drivers/net/ethernet/realtek/r8169_phy_config.c
>>>>>> index 50f0f621b..60014b9c4 100644
>>>>>> --- a/drivers/net/ethernet/realtek/r8169_phy_config.c
>>>>>> +++ b/drivers/net/ethernet/realtek/r8169_phy_config.c
>>>>>> @@ -1153,6 +1153,7 @@ static void rtl8106e_hw_phy_config(struct rtl8169_private *tp,
>>>>>> r8169_apply_firmware(tp);
>>>>>>
>>>>>> rtl_writephy_batch(phydev, phy_reg_init);
>>>>>> + phy_write(phydev, 0x18, 0x8310);
>>>>>> }
>>>>>>
>>>>>> static void rtl8125_legacy_force_mode(struct phy_device *phydev)
>>>>>> --
>>>>>> 2.32.0
>>>>>>
>>>>>>
>>>>
>>