running the rt61pci module on 2.6.31.5 works fine, but using the recent
linus/master (2.6.32-rc5) results in this:
[ 2112.943630] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2.
[...]
[ 2827.646318] phy0 -> rt61pci_wait_bbp_ready: Error - BBP register access failed, aborting.
[ 2827.646323] phy0 -> rt61pci_set_device_state: Error - Device failed to enter state 4 (-5).
[ 2873.143407] BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
[ 2873.143413] IP: [<ffffffffa01e7290>] rt2x00pci_free_queue_dma+0x20/0xd0 [rt2x00pci]
[ 2873.143421] PGD 2dec1a067 PUD 26c1bc067 PMD 0
[ 2873.143426] Oops: 0000 [#1] PREEMPT SMP
[ 2873.143429] last sysfs file: /sys/devices/platform/coretemp.3/temp1_input
[ 2873.143433] CPU 0
[ 2873.143434] Modules linked in: binfmt_misc ppdev nvidia(P) ipt_REJECT ipt_LOG xt_limit xt_tcpudp xt_state ipt_addrtype snd_hda_codec_realtek ip6table_filter ip6_tables nf_nat_irc coretemp arc4 snd_hda_intel nf_conntrack_irc snd_hda_codec snd_hdsp nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 snd_pcm_oss rt61pci(-) crc_itu_t snd_mixer_oss nf_conntrack_ftp lp snd_pcm nf_conntrack rt2x00pci snd_hwdep parport iptable_filter rt2x00lib snd_seq_dummy snd_seq_oss snd_seq_midi ip_tables x_tables led_class snd_rawmidi snd_seq_midi_event snd_seq mac80211 snd_timer snd_seq_device cfg80211 eeprom_93cx6 snd psmouse pcmcia soundcore snd_page_alloc serio_raw yenta_socket rsrc_nonstatic pcmcia_core xfs exportfs usbhid r8169 mii floppy
[ 2873.143487] Pid: 4677, comm: rmmod Tainted: P 2.6.32-rc5 #35 System Product Name
[ 2873.143490] RIP: 0010:[<ffffffffa01e7290>] [<ffffffffa01e7290>] rt2x00pci_free_queue_dma+0x20/0xd0 [rt2x00pci]
[ 2873.143496] RSP: 0018:ffff880305e53cf8 EFLAGS: 00010282
[ 2873.143499] RAX: 0000000000000000 RBX: ffff8803312e51e0 RCX: 0000000000000000
[ 2873.143501] RDX: 0000000000000150 RSI: ffff880331290c00 RDI: ffff8803312e51e0
[ 2873.143504] RBP: ffff880305e53d38 R08: 0000000000000000 R09: 0000000000000000
[ 2873.143506] R10: 0000000000000001 R11: 0000000000000000 R12: ffff880331290c38
[ 2873.143508] R13: ffff8803312e4340 R14: ffff8803312e51e0 R15: 0000000000000001
[ 2873.143511] FS: 00007f4e38e146f0(0000) GS:ffff880028200000(0000) knlGS:0000000000000000
[ 2873.143514] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 2873.143517] CR2: 0000000000000020 CR3: 00000002b2e66000 CR4: 00000000000006b0
[ 2873.143519] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 2873.143522] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 2873.143525] Process rmmod (pid: 4677, threadinfo ffff880305e52000, task ffff880305f50000)
[ 2873.143527] Stack:
[ 2873.143528] ffff8803312e51e0 0000000000000001 ffff880305e53d38 ffff8803312e51e0
[ 2873.143532] <0> ffff880331290c38 ffff8803312e4340 ffff8803312e51e0 0000000000000001
[ 2873.143537] <0> ffff880305e53d58 ffffffffa01e7378 ffff8803312e51e0 ffff880333afc080
[ 2873.143542] Call Trace:
[ 2873.143548] [<ffffffffa01e7378>] rt2x00pci_uninitialize+0x38/0x70 [rt2x00pci]
[ 2873.143554] [<ffffffffa01c8062>] rt2x00lib_uninitialize+0x32/0x60 [rt2x00lib]
[ 2873.143560] [<ffffffffa01c886d>] rt2x00lib_remove_dev+0x2d/0xc0 [rt2x00lib]
[ 2873.143565] [<ffffffffa01e718c>] rt2x00pci_remove+0x3c/0x120 [rt2x00pci]
[ 2873.143572] [<ffffffff81298fbf>] pci_device_remove+0x2f/0x60
[ 2873.143578] [<ffffffff8132eec3>] __device_release_driver+0x53/0xb0
[ 2873.143582] [<ffffffff8132efe0>] driver_detach+0xc0/0xd0
[ 2873.143587] [<ffffffff8132df44>] bus_remove_driver+0x94/0xc0
[ 2873.143591] [<ffffffff8132f5a9>] driver_unregister+0x59/0x90
[ 2873.143595] [<ffffffff8129925f>] pci_unregister_driver+0x3f/0xb0
[ 2873.143601] [<ffffffffa024f290>] rt61pci_exit+0x10/0x12 [rt61pci]
[ 2873.143608] [<ffffffff810923f3>] sys_delete_module+0x183/0x250
[ 2873.143613] [<ffffffff8107dbe9>] ? up_read+0x9/0x10
[ 2873.143618] [<ffffffff815351df>] ? do_page_fault+0x13f/0x3f0
[ 2873.143624] [<ffffffff81011f02>] system_call_fastpath+0x16/0x1b
[ 2873.143627] Code: b8 ea ff ff ff eb b3 0f 1f 40 00 55 48 89 e5 48 83 ec 40 48 89 5d d8 4c 89 65 e0 4c 89 6d e8 4c 89 75 f0 4c 89 7d f8 48 8b 46 08 <48> 8b 58 20 48 8b 13 48 85 d2 74 4c 4c 8b 27 48 8b 4b 08 44 0f
[ 2873.143663] RIP [<ffffffffa01e7290>] rt2x00pci_free_queue_dma+0x20/0xd0 [rt2x00pci]
[ 2873.143669] RSP <ffff880305e53cf8>
[ 2873.143670] CR2: 0000000000000020
[ 2873.143673] ---[ end trace af6b473a456cf4f3 ]---
full bootlog attached.
hth, tim
--
[email protected]
http://tim.klingt.org
After one look at this planet any visitor from outer space would say
"I want to see the manager."
William S. Burroughs
On 11/04/2009 07:00 PM, Tim Blechmann wrote:
>> running the rt61pci module on 2.6.31.5 works fine, but using the recent
>> linus/master (2.6.32-rc5) results in this:
>
> same issue with 2.6.32-rc5 ... new bootlog with more debugging info
> attached ...
i was still able to reproduce this issue with 2.6.32-rc8 ... it would
be nice, if someone could have a look into this issue before 2.6.32 is
released ...
dmesg from 2.6.32-rc8:
[ 10.249098] rt61pci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 10.257182] phy0 -> rt61pci_validate_eeprom: EEPROM recovery - NIC: 0xff80
[ 10.257184] phy0 -> rt61pci_validate_eeprom: EEPROM recovery - Led: 0xe0ff
[ 10.257187] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 0302, rf: 0003, rev: 0002561c.
[ 10.351794] Registered led device: rt61pci-phy0::radio
[ 10.351839] Registered led device: rt61pci-phy0::assoc
[ 14.342046] rt61pci 0000:06:00.0: firmware: requesting rt2561.bin
[ 14.395533] phy0 -> rt2x00lib_request_firmware: Info - Firmware detected - version: 0.8.
[ 14.421238] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 102.
[ 14.421245] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 4, CWmax: 5, Aifs: 2, TXop: 188.
[ 14.421252] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 3, TXop: 0.
[ 14.421258] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 7, TXop: 0.
[ 273.404685] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2.
[ 273.404687] Please file bug report to http://rt2x00.serialmonkey.com.
[ 282.143549] wlan0: no IPv6 routers present
[ 357.304908] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 2
[ 357.333806] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 9
[ 360.172776] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2.
[ 360.172778] Please file bug report to http://rt2x00.serialmonkey.com.
[ 360.172782] phy0 -> rt2x00mac_tx_rts_cts: Warning - Failed to send RTS/CTS frame.
[ 383.880010] No probe response from AP 00:24:fe:09:94:18 after 500ms, disconnecting.
[ 383.880026] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
[ 383.880034] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
[ 383.880042] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
[ 383.880050] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
[ 385.220460] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 1)
[ 385.421337] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 2)
[ 385.621304] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 3)
[ 385.821264] wlan0: direct probe to AP 00:24:fe:09:94:18 timed out
lspci -vvv:
06:00.0 Network controller: RaLink RT2561/RT61 rev B 802.11g
Subsystem: D-Link System Inc Device 3c09
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fb6f8000 (32-bit, non-prefetchable) [size=32K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: rt61pci
Kernel modules: rt61pci
thanks, tim
--
[email protected]
http://tim.klingt.org
Happiness is a byproduct of function, purpose, and conflict; those who
seek happiness for itself seek victory without war.
William S. Burroughs
> running the rt61pci module on 2.6.31.5 works fine, but using the recent
> linus/master (2.6.32-rc5) results in this:
same issue with 2.6.32-rc5 ... new bootlog with more debugging info
attached ...
tim
--
[email protected]
http://tim.klingt.org
Life is really simple, but we insist on making it complicated.
Confucius
On Wed, Nov 4, 2009 at 19:27, Matthijs Kooijman <[email protected]> wrote:
>> [ 1656.653963] Please file bug report to http://rt2x00.serialmonkey.com
>>
>> Is that message correct? ?The bug reports link at the wiki seems a bit unclear...
> Also, I just noticed that the "mailing lists" link in the first section, as
> well as the "LISTS" link in the menu bar at the top point to the old
> sourceforge lists page, which is empty.
>
> Perhaps the frontpage should be reviewed a bit?
>
> Gr.
>
> Matthijs
>
I've notified Mark, our webmaster.
Hopefully, we'll have it fixed in a couple of days, thanks for the notice.
Luis Correia
rt2x00 project admin
On Sun, Nov 29, 2009 at 3:01 PM, Tim Blechmann <[email protected]> wrote:
> On 11/04/2009 07:00 PM, Tim Blechmann wrote:
>>> running the rt61pci module on 2.6.31.5 works fine, but using the recent
>>> linus/master (2.6.32-rc5) results in this:
>>
>> same issue with 2.6.32-rc5 ... new bootlog with more debugging info
>> attached ...
>
> i was still able to reproduce this issue with 2.6.32-rc8 ... it would
> be nice, if someone could have a look into this issue before 2.6.32 is
> released ...
>
> dmesg from 2.6.32-rc8:
> [ ? 10.249098] rt61pci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
> [ ? 10.257182] phy0 -> rt61pci_validate_eeprom: EEPROM recovery - NIC: 0xff80
> [ ? 10.257184] phy0 -> rt61pci_validate_eeprom: EEPROM recovery - Led: 0xe0ff
> [ ? 10.257187] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 0302, rf: 0003, rev: 0002561c.
> [ ? 10.351794] Registered led device: rt61pci-phy0::radio
> [ ? 10.351839] Registered led device: rt61pci-phy0::assoc
> [ ? 14.342046] rt61pci 0000:06:00.0: firmware: requesting rt2561.bin
> [ ? 14.395533] phy0 -> rt2x00lib_request_firmware: Info - Firmware detected - version: 0.8.
> [ ? 14.421238] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 102.
> [ ? 14.421245] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 4, CWmax: 5, Aifs: 2, TXop: 188.
> [ ? 14.421252] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 3, TXop: 0.
> [ ? 14.421258] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 7, TXop: 0.
> [ ?273.404685] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2.
> [ ?273.404687] Please file bug report to http://rt2x00.serialmonkey.com.
> [ ?282.143549] wlan0: no IPv6 routers present
> [ ?357.304908] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 2
> [ ?357.333806] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 9
> [ ?360.172776] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2.
> [ ?360.172778] Please file bug report to http://rt2x00.serialmonkey.com.
> [ ?360.172782] phy0 -> rt2x00mac_tx_rts_cts: Warning - Failed to send RTS/CTS frame.
> [ ?383.880010] No probe response from AP 00:24:fe:09:94:18 after 500ms, disconnecting.
> [ ?383.880026] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ ?383.880034] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ ?383.880042] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ ?383.880050] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ ?385.220460] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 1)
> [ ?385.421337] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 2)
> [ ?385.621304] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 3)
> [ ?385.821264] wlan0: direct probe to AP 00:24:fe:09:94:18 timed out
>
>
> lspci -vvv:
>
> 06:00.0 Network controller: RaLink RT2561/RT61 rev B 802.11g
> ? ? ? ?Subsystem: D-Link System Inc Device 3c09
> ? ? ? ?Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> ? ? ? ?Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> ? ? ? ?Latency: 64, Cache Line Size: 64 bytes
> ? ? ? ?Interrupt: pin A routed to IRQ 16
> ? ? ? ?Region 0: Memory at fb6f8000 (32-bit, non-prefetchable) [size=32K]
> ? ? ? ?Capabilities: [40] Power Management version 2
> ? ? ? ? ? ? ? ?Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> ? ? ? ? ? ? ? ?Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> ? ? ? ?Kernel driver in use: rt61pci
> ? ? ? ?Kernel modules: rt61pci
>
> thanks, tim
Could you please try a bisect between 2.6.31 and 2.6.32-rc5? That
should reveal the faulty commit.
>
> --
> [email protected]
> http://tim.klingt.org
>
> Happiness is a byproduct of function, purpose, and conflict; those who
> seek happiness for itself seek victory without war.
> ?William S. Burroughs
>
>
--
Vista: [V]iruses, [I]ntruders, [S]pyware, [T]rojans and [A]dware. :-)
> [ 1656.653963] Please file bug report to http://rt2x00.serialmonkey.com
>
> Is that message correct? The bug reports link at the wiki seems a bit unclear...
Also, I just noticed that the "mailing lists" link in the first section, as
well as the "LISTS" link in the menu bar at the top point to the old
sourceforge lists page, which is empty.
Perhaps the frontpage should be reviewed a bit?
Gr.
Matthijs
[ 1591.626628] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
[ 1591.626636] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
[ 1591.626644] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
[ 1591.626652] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
[ 1656.653960] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2.
[ 1656.653963] Please file bug report to http://rt2x00.serialmonkey.com
Near the bottom...
Is that message correct? The bug reports link at the wiki seems a bit unclear...
John
On Wed, Nov 04, 2009 at 07:00:54PM +0100, Tim Blechmann wrote:
> > running the rt61pci module on 2.6.31.5 works fine, but using the recent
> > linus/master (2.6.32-rc5) results in this:
>
> same issue with 2.6.32-rc5 ... new bootlog with more debugging info
> attached ...
>
> tim
>
> --
> [email protected]
> http://tim.klingt.org
>
> Life is really simple, but we insist on making it complicated.
> Confucius
> [ 0.000000] Initializing cgroup subsys cpuset
> [ 0.000000] Initializing cgroup subsys cpu
> [ 0.000000] Linux version 2.6.32-rc6 (tim@moka) (gcc version 4.4.1 (Ubuntu 4.4.1-4ubuntu8) ) #36 SMP PREEMPT Wed Nov 4 01:03:33 CET 2009
> [ 0.000000] Command line: root=UUID=f4e801b1-b54a-4002-a3e3-328308ad48fb ro splash vga=769
> [ 0.000000] KERNEL supported cpus:
> [ 0.000000] Intel GenuineIntel
> [ 0.000000] AMD AuthenticAMD
> [ 0.000000] Centaur CentaurHauls
> [ 0.000000] BIOS-provided physical RAM map:
> [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> [ 0.000000] BIOS-e820: 00000000000e4c00 - 0000000000100000 (reserved)
> [ 0.000000] BIOS-e820: 0000000000100000 - 00000000bf680000 (usable)
> [ 0.000000] BIOS-e820: 00000000bf680000 - 00000000bf698000 (ACPI data)
> [ 0.000000] BIOS-e820: 00000000bf698000 - 00000000bf6dc000 (ACPI NVS)
> [ 0.000000] BIOS-e820: 00000000bf6dc000 - 00000000c0000000 (reserved)
> [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> [ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
> [ 0.000000] BIOS-e820: 0000000100000000 - 0000000340000000 (usable)
> [ 0.000000] DMI 2.5 present.
> [ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it.
> [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
> [ 0.000000] last_pfn = 0x340000 max_arch_pfn = 0x400000000
> [ 0.000000] MTRR default type: uncachable
> [ 0.000000] MTRR fixed ranges enabled:
> [ 0.000000] 00000-9FFFF write-back
> [ 0.000000] A0000-BFFFF uncachable
> [ 0.000000] C0000-E3FFF write-protect
> [ 0.000000] E4000-EBFFF write-through
> [ 0.000000] EC000-FFFFF write-protect
> [ 0.000000] MTRR variable ranges enabled:
> [ 0.000000] 0 base 000000000 mask E00000000 write-back
> [ 0.000000] 1 base 200000000 mask F00000000 write-back
> [ 0.000000] 2 base 300000000 mask FC0000000 write-back
> [ 0.000000] 3 base 0C0000000 mask FC0000000 uncachable
> [ 0.000000] 4 base 0BF700000 mask FFFF00000 uncachable
> [ 0.000000] 5 base 0BF800000 mask FFF800000 uncachable
> [ 0.000000] 6 disabled
> [ 0.000000] 7 disabled
> [ 0.000000] e820 update range: 00000000bf700000 - 0000000100000000 (usable) ==> (reserved)
> [ 0.000000] last_pfn = 0xbf680 max_arch_pfn = 0x400000000
> [ 0.000000] Scanning 0 areas for low memory corruption
> [ 0.000000] modified physical RAM map:
> [ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved)
> [ 0.000000] modified: 0000000000010000 - 000000000009fc00 (usable)
> [ 0.000000] modified: 000000000009fc00 - 00000000000a0000 (reserved)
> [ 0.000000] modified: 00000000000e4c00 - 0000000000100000 (reserved)
> [ 0.000000] modified: 0000000000100000 - 00000000bf680000 (usable)
> [ 0.000000] modified: 00000000bf680000 - 00000000bf698000 (ACPI data)
> [ 0.000000] modified: 00000000bf698000 - 00000000bf6dc000 (ACPI NVS)
> [ 0.000000] modified: 00000000bf6dc000 - 00000000c0000000 (reserved)
> [ 0.000000] modified: 00000000fee00000 - 00000000fee01000 (reserved)
> [ 0.000000] modified: 00000000ffe00000 - 0000000100000000 (reserved)
> [ 0.000000] modified: 0000000100000000 - 0000000340000000 (usable)
> [ 0.000000] initial memory mapped : 0 - 20000000
> [ 0.000000] init_memory_mapping: 0000000000000000-00000000bf680000
> [ 0.000000] 0000000000 - 00bf600000 page 2M
> [ 0.000000] 00bf600000 - 00bf680000 page 4k
> [ 0.000000] kernel direct mapping tables up to bf680000 @ 10000-15000
> [ 0.000000] init_memory_mapping: 0000000100000000-0000000340000000
> [ 0.000000] 0100000000 - 0340000000 page 2M
> [ 0.000000] kernel direct mapping tables up to 340000000 @ 13000-21000
> [ 0.000000] RAMDISK: 37868000 - 37fef45a
> [ 0.000000] ACPI: RSDP 00000000000fabd0 00024 (v02 ACPIAM)
> [ 0.000000] ACPI: XSDT 00000000bf680100 0005C (v01 022609 XSDT1156 20090226 MSFT 00000097)
> [ 0.000000] ACPI: FACP 00000000bf680290 000F4 (v03 022609 FACP1156 20090226 MSFT 00000097)
> [ 0.000000] ACPI: DSDT 00000000bf6804b0 0C3DD (v01 A1146 A1146001 00000001 INTL 20060113)
> [ 0.000000] ACPI: FACS 00000000bf698000 00040
> [ 0.000000] ACPI: APIC 00000000bf680390 000D8 (v01 022609 APIC1156 20090226 MSFT 00000097)
> [ 0.000000] ACPI: MCFG 00000000bf680470 0003C (v01 022609 OEMMCFG 20090226 MSFT 00000097)
> [ 0.000000] ACPI: OEMB 00000000bf698040 00072 (v01 022609 OEMB1156 20090226 MSFT 00000097)
> [ 0.000000] ACPI: HPET 00000000bf68f4b0 00038 (v01 022609 OEMHPET 20090226 MSFT 00000097)
> [ 0.000000] ACPI: OSFR 00000000bf68f4f0 000B0 (v01 022609 OEMOSFR 20090226 MSFT 00000097)
> [ 0.000000] ACPI: SSDT 00000000bf69a8f0 0249F (v01 DpgPmm CpuPm 00000012 INTL 20060113)
> [ 0.000000] ACPI: Local APIC address 0xfee00000
> [ 0.000000] (8 early reservations) ==> bootmem [0000000000 - 0340000000]
> [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
> [ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
> [ 0.000000] #2 [0001000000 - 00019a6d44] TEXT DATA BSS ==> [0001000000 - 00019a6d44]
> [ 0.000000] #3 [0037868000 - 0037fef45a] RAMDISK ==> [0037868000 - 0037fef45a]
> [ 0.000000] #4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
> [ 0.000000] #5 [00019a7000 - 00019a7288] BRK ==> [00019a7000 - 00019a7288]
> [ 0.000000] #6 [0000010000 - 0000013000] PGTABLE ==> [0000010000 - 0000013000]
> [ 0.000000] #7 [0000013000 - 000001c000] PGTABLE ==> [0000013000 - 000001c000]
> [ 0.000000] found SMP MP-table at [ffff8800000ff780] ff780
> [ 0.000000] [ffffea0000000000-ffffea000b5fffff] PMD -> [ffff880028600000-ffff880032dfffff] on node 0
> [ 0.000000] Zone PFN ranges:
> [ 0.000000] DMA 0x00000010 -> 0x00001000
> [ 0.000000] DMA32 0x00001000 -> 0x00100000
> [ 0.000000] Normal 0x00100000 -> 0x00340000
> [ 0.000000] Movable zone start PFN for each node
> [ 0.000000] early_node_map[3] active PFN ranges
> [ 0.000000] 0: 0x00000010 -> 0x0000009f
> [ 0.000000] 0: 0x00000100 -> 0x000bf680
> [ 0.000000] 0: 0x00100000 -> 0x00340000
> [ 0.000000] On node 0 totalpages: 3143183
> [ 0.000000] DMA zone: 56 pages used for memmap
> [ 0.000000] DMA zone: 111 pages reserved
> [ 0.000000] DMA zone: 3816 pages, LIFO batch:0
> [ 0.000000] DMA32 zone: 14280 pages used for memmap
> [ 0.000000] DMA32 zone: 765624 pages, LIFO batch:31
> [ 0.000000] Normal zone: 32256 pages used for memmap
> [ 0.000000] Normal zone: 2327040 pages, LIFO batch:31
> [ 0.000000] ACPI: PM-Timer IO Port: 0x808
> [ 0.000000] ACPI: Local APIC address 0xfee00000
> [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x01] enabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x03] enabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x05] enabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x88] disabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x89] disabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x8a] disabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x8b] disabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x8c] disabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x8d] disabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x8e] disabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x10] lapic_id[0x8f] disabled)
> [ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
> [ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
> [ 0.000000] ACPI: IOAPIC (id[0x09] address[0xfec8a000] gsi_base[24])
> [ 0.000000] IOAPIC[1]: apic_id 9, version 32, address 0xfec8a000, GSI 24-47
> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> [ 0.000000] ACPI: IRQ0 used by override.
> [ 0.000000] ACPI: IRQ2 used by override.
> [ 0.000000] ACPI: IRQ9 used by override.
> [ 0.000000] Using ACPI (MADT) for SMP configuration information
> [ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
> [ 0.000000] 16 Processors exceeds NR_CPUS limit of 8
> [ 0.000000] SMP: Allowing 8 CPUs, 0 hotplug CPUs
> [ 0.000000] nr_irqs_gsi: 48
> [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
> [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e5000
> [ 0.000000] PM: Registered nosave memory: 00000000000e5000 - 0000000000100000
> [ 0.000000] PM: Registered nosave memory: 00000000bf680000 - 00000000bf698000
> [ 0.000000] PM: Registered nosave memory: 00000000bf698000 - 00000000bf6dc000
> [ 0.000000] PM: Registered nosave memory: 00000000bf6dc000 - 00000000c0000000
> [ 0.000000] PM: Registered nosave memory: 00000000c0000000 - 00000000fee00000
> [ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
> [ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffe00000
> [ 0.000000] PM: Registered nosave memory: 00000000ffe00000 - 0000000100000000
> [ 0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:3ee00000)
> [ 0.000000] Booting paravirtualized kernel on bare hardware
> [ 0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
> [ 0.000000] PERCPU: Embedded 30 pages/cpu @ffff880028200000 s90200 r8192 d24488 u262144
> [ 0.000000] pcpu-alloc: s90200 r8192 d24488 u262144 alloc=1*2097152
> [ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 3096480
> [ 0.000000] Kernel command line: root=UUID=f4e801b1-b54a-4002-a3e3-328308ad48fb ro splash vga=769
> [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
> [ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
> [ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
> [ 0.000000] Initializing CPU#0
> [ 0.000000] Checking aperture...
> [ 0.000000] No AGP bridge found
> [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
> [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
> [ 0.000000] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
> [ 0.000000] Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000
> [ 0.000000] software IO TLB at phys 0x20000000 - 0x24000000
> [ 0.000000] Memory: 12290392k/13631488k available (5351k kernel code, 1058756k absent, 281452k reserved, 2986k data, 540k init)
> [ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
> [ 0.000000] Hierarchical RCU implementation.
> [ 0.000000] NR_IRQS:512
> [ 0.000000] Extended CMOS year: 2000
> [ 0.000000] Console: colour VGA+ 80x25
> [ 0.000000] console [tty0] enabled
> [ 0.000000] allocated 125829120 bytes of page_cgroup
> [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
> [ 0.000000] hpet clockevent registered
> [ 0.000000] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
> [ 0.000000] Fast TSC calibration using PIT
> [ 0.010000] Detected 2672.606 MHz processor.
> [ 0.000003] Calibrating delay loop (skipped), value calculated using timer frequency.. 5345.21 BogoMIPS (lpj=26726060)
> [ 0.000121] Security Framework initialized
> [ 0.000174] SELinux: Disabled at boot.
> [ 0.000229] Mount-cache hash table entries: 256
> [ 0.000356] Initializing cgroup subsys ns
> [ 0.000408] Initializing cgroup subsys cpuacct
> [ 0.000462] Initializing cgroup subsys memory
> [ 0.000515] Initializing cgroup subsys freezer
> [ 0.000578] CPU: Physical Processor ID: 0
> [ 0.000630] CPU: Processor Core ID: 0
> [ 0.000682] CPU: L1 I cache: 32K, L1 D cache: 32K
> [ 0.000765] CPU: L2 cache: 256K
> [ 0.000814] CPU: L3 cache: 8192K
> [ 0.000865] using mwait in idle threads.
> [ 0.000916] Performance Events: Nehalem/Corei7 events, Intel PMU driver.
> [ 0.001035] ... version: 3
> [ 0.001086] ... bit width: 48
> [ 0.001136] ... generic registers: 4
> [ 0.001187] ... value mask: 0000ffffffffffff
> [ 0.001240] ... max period: 000000007fffffff
> [ 0.001293] ... fixed-purpose events: 3
> [ 0.001344] ... event mask: 000000070000000f
> [ 0.002090] ACPI: Core revision 20090903
> [ 0.038176] Setting APIC routing to flat
> [ 0.038676] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
> [ 0.138701] CPU0: Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz stepping 05
> [ 0.308525] Booting processor 1 APIC 0x2 ip 0x6000
> [ 0.318842] Initializing CPU#1
> [ 0.467616] Calibrating delay using timer specific routine.. 5317.40 BogoMIPS (lpj=26587025)
> [ 0.467624] CPU: Physical Processor ID: 0
> [ 0.467625] CPU: Processor Core ID: 1
> [ 0.467627] CPU: L1 I cache: 32K, L1 D cache: 32K
> [ 0.467628] CPU: L2 cache: 256K
> [ 0.467629] CPU: L3 cache: 8192K
> [ 0.467663] CPU1: Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz stepping 05
> [ 0.468895] Skipping synchronization checks as TSC is reliable.
> [ 0.497467] Booting processor 2 APIC 0x4 ip 0x6000
> [ 0.507879] Initializing CPU#2
> [ 0.656557] Calibrating delay using timer specific routine.. 5317.41 BogoMIPS (lpj=26587054)
> [ 0.656563] CPU: Physical Processor ID: 0
> [ 0.656564] CPU: Processor Core ID: 2
> [ 0.656566] CPU: L1 I cache: 32K, L1 D cache: 32K
> [ 0.656567] CPU: L2 cache: 256K
> [ 0.656568] CPU: L3 cache: 8192K
> [ 0.656578] CPU2: Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz stepping 05
> [ 0.686417] Booting processor 3 APIC 0x6 ip 0x6000
> [ 0.696730] Initializing CPU#3
> [ 0.845503] Calibrating delay using timer specific routine.. 5317.40 BogoMIPS (lpj=26587036)
> [ 0.845509] CPU: Physical Processor ID: 0
> [ 0.845510] CPU: Processor Core ID: 3
> [ 0.845512] CPU: L1 I cache: 32K, L1 D cache: 32K
> [ 0.845514] CPU: L2 cache: 256K
> [ 0.845514] CPU: L3 cache: 8192K
> [ 0.845530] CPU3: Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz stepping 05
> [ 0.875358] Booting processor 4 APIC 0x1 ip 0x6000
> [ 0.885771] Initializing CPU#4
> [ 1.034447] Calibrating delay using timer specific routine.. 5317.41 BogoMIPS (lpj=26587077)
> [ 1.034456] CPU: Physical Processor ID: 0
> [ 1.034457] CPU: Processor Core ID: 0
> [ 1.034460] CPU: L1 I cache: 32K, L1 D cache: 32K
> [ 1.034462] CPU: L2 cache: 256K
> [ 1.034463] CPU: L3 cache: 8192K
> [ 1.034550] CPU4: Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz stepping 05
> [ 1.064298] Booting processor 5 APIC 0x3 ip 0x6000
> [ 1.074612] Initializing CPU#5
> [ 1.223389] Calibrating delay using timer specific routine.. 5317.27 BogoMIPS (lpj=26586378)
> [ 1.223396] CPU: Physical Processor ID: 0
> [ 1.223397] CPU: Processor Core ID: 1
> [ 1.223399] CPU: L1 I cache: 32K, L1 D cache: 32K
> [ 1.223400] CPU: L2 cache: 256K
> [ 1.223401] CPU: L3 cache: 8192K
> [ 1.223404] CPU5: Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz stepping 05
> [ 1.253242] Booting processor 6 APIC 0x5 ip 0x6000
> [ 1.263656] Initializing CPU#6
> [ 1.412330] Calibrating delay using timer specific routine.. 5317.41 BogoMIPS (lpj=26587050)
> [ 1.412336] CPU: Physical Processor ID: 0
> [ 1.412337] CPU: Processor Core ID: 2
> [ 1.412339] CPU: L1 I cache: 32K, L1 D cache: 32K
> [ 1.412341] CPU: L2 cache: 256K
> [ 1.412341] CPU: L3 cache: 8192K
> [ 1.412355] CPU6: Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz stepping 05
> [ 1.442215] Booting processor 7 APIC 0x7 ip 0x6000
> [ 1.452531] Initializing CPU#7
> [ 1.601277] Calibrating delay using timer specific routine.. 5317.40 BogoMIPS (lpj=26587018)
> [ 1.601283] CPU: Physical Processor ID: 0
> [ 1.601284] CPU: Processor Core ID: 3
> [ 1.601286] CPU: L1 I cache: 32K, L1 D cache: 32K
> [ 1.601287] CPU: L2 cache: 256K
> [ 1.601288] CPU: L3 cache: 8192K
> [ 1.601346] CPU7: Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz stepping 05
> [ 1.601848] Brought up 8 CPUs
> [ 1.601898] Total of 8 processors activated (42566.93 BogoMIPS).
> [ 1.605179] CPU0 attaching sched-domain:
> [ 1.605182] domain 0: span 0,4 level SIBLING
> [ 1.605184] groups: 0 (cpu_power = 589) 4 (cpu_power = 589)
> [ 1.605187] domain 1: span 0-7 level MC
> [ 1.605189] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178)
> [ 1.605196] CPU1 attaching sched-domain:
> [ 1.605198] domain 0: span 1,5 level SIBLING
> [ 1.605199] groups: 1 (cpu_power = 589) 5 (cpu_power = 589)
> [ 1.605202] domain 1: span 0-7 level MC
> [ 1.605204] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178)
> [ 1.605210] CPU2 attaching sched-domain:
> [ 1.605211] domain 0: span 2,6 level SIBLING
> [ 1.605212] groups: 2 (cpu_power = 589) 6 (cpu_power = 589)
> [ 1.605216] domain 1: span 0-7 level MC
> [ 1.605217] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178)
> [ 1.605223] CPU3 attaching sched-domain:
> [ 1.605224] domain 0: span 3,7 level SIBLING
> [ 1.605226] groups: 3 (cpu_power = 589) 7 (cpu_power = 589)
> [ 1.605229] domain 1: span 0-7 level MC
> [ 1.605231] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178)
> [ 1.605236] CPU4 attaching sched-domain:
> [ 1.605238] domain 0: span 0,4 level SIBLING
> [ 1.605239] groups: 4 (cpu_power = 589) 0 (cpu_power = 589)
> [ 1.605242] domain 1: span 0-7 level MC
> [ 1.605244] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178)
> [ 1.605250] CPU5 attaching sched-domain:
> [ 1.605251] domain 0: span 1,5 level SIBLING
> [ 1.605252] groups: 5 (cpu_power = 589) 1 (cpu_power = 589)
> [ 1.605256] domain 1: span 0-7 level MC
> [ 1.605257] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178)
> [ 1.605263] CPU6 attaching sched-domain:
> [ 1.605264] domain 0: span 2,6 level SIBLING
> [ 1.605266] groups: 6 (cpu_power = 589) 2 (cpu_power = 589)
> [ 1.605269] domain 1: span 0-7 level MC
> [ 1.605270] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178)
> [ 1.605276] CPU7 attaching sched-domain:
> [ 1.605278] domain 0: span 3,7 level SIBLING
> [ 1.605279] groups: 7 (cpu_power = 589) 3 (cpu_power = 589)
> [ 1.605282] domain 1: span 0-7 level MC
> [ 1.605284] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178)
> [ 1.605756] regulator: core version 0.5
> [ 1.605829] Time: 17:10:51 Date: 11/04/09
> [ 1.605908] NET: Registered protocol family 16
> [ 1.606032] ACPI: bus type pci registered
> [ 1.606129] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
> [ 1.606186] PCI: Not using MMCONFIG.
> [ 1.606236] PCI: Using configuration type 1 for base access
> [ 1.606874] bio: create slab <bio-0> at 0
> [ 1.607794] ACPI: EC: Look up EC in DSDT
> [ 1.610167] ACPI: Executed 1 blocks of module-level executable AML code
> [ 1.640134] ACPI: Interpreter enabled
> [ 1.640189] ACPI: (supports S0 S1 S3 S4 S5)
> [ 1.640412] ACPI: Using IOAPIC for interrupt routing
> [ 1.640514] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
> [ 1.642726] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
> [ 1.646706] PCI: Using MMCONFIG at e0000000 - efffffff
> [ 1.654909] ACPI Warning: Incorrect checksum in table [OEMB] - 8B, should be 83 (20090903/tbutils-314)
> [ 1.655173] ACPI: No dock devices found.
> [ 1.655351] ACPI: PCI Root Bridge [PCI0] (0000:00)
> [ 1.655467] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
> [ 1.655524] pci 0000:00:00.0: PME# disabled
> [ 1.655630] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
> [ 1.655686] pci 0000:00:01.0: PME# disabled
> [ 1.655793] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
> [ 1.655849] pci 0000:00:03.0: PME# disabled
> [ 1.655957] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
> [ 1.656013] pci 0000:00:07.0: PME# disabled
> [ 1.656348] pci 0000:00:1a.0: reg 20 io port: [0xb800-0xb81f]
> [ 1.656409] pci 0000:00:1a.1: reg 20 io port: [0xb880-0xb89f]
> [ 1.656469] pci 0000:00:1a.2: reg 20 io port: [0xbc00-0xbc1f]
> [ 1.656533] pci 0000:00:1a.7: reg 10 32bit mmio: [0xf7fff000-0xf7fff3ff]
> [ 1.656582] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
> [ 1.656639] pci 0000:00:1a.7: PME# disabled
> [ 1.656725] pci 0000:00:1b.0: reg 10 64bit mmio: [0xf7ff8000-0xf7ffbfff]
> [ 1.656761] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
> [ 1.656817] pci 0000:00:1b.0: PME# disabled
> [ 1.656921] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
> [ 1.656977] pci 0000:00:1c.0: PME# disabled
> [ 1.657083] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
> [ 1.657139] pci 0000:00:1c.2: PME# disabled
> [ 1.657238] pci 0000:00:1d.0: reg 20 io port: [0xb080-0xb09f]
> [ 1.657299] pci 0000:00:1d.1: reg 20 io port: [0xb400-0xb41f]
> [ 1.657360] pci 0000:00:1d.2: reg 20 io port: [0xb480-0xb49f]
> [ 1.657426] pci 0000:00:1d.7: reg 10 32bit mmio: [0xf7ffe000-0xf7ffe3ff]
> [ 1.657475] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
> [ 1.657532] pci 0000:00:1d.7: PME# disabled
> [ 1.657691] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
> [ 1.657763] pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
> [ 1.657821] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0294 (mask 0003)
> [ 1.657894] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 4700 (mask 001f)
> [ 1.658009] pci 0000:00:1f.2: reg 10 io port: [0xa000-0xa007]
> [ 1.658013] pci 0000:00:1f.2: reg 14 io port: [0x9c00-0x9c03]
> [ 1.658018] pci 0000:00:1f.2: reg 18 io port: [0x9880-0x9887]
> [ 1.658022] pci 0000:00:1f.2: reg 1c io port: [0x9800-0x9803]
> [ 1.658027] pci 0000:00:1f.2: reg 20 io port: [0x9480-0x948f]
> [ 1.658032] pci 0000:00:1f.2: reg 24 io port: [0x9400-0x940f]
> [ 1.658072] pci 0000:00:1f.3: reg 10 64bit mmio: [0xf7ffd000-0xf7ffd0ff]
> [ 1.658083] pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
> [ 1.658121] pci 0000:00:1f.5: reg 10 io port: [0xb000-0xb007]
> [ 1.658125] pci 0000:00:1f.5: reg 14 io port: [0xac00-0xac03]
> [ 1.658130] pci 0000:00:1f.5: reg 18 io port: [0xa880-0xa887]
> [ 1.658135] pci 0000:00:1f.5: reg 1c io port: [0xa800-0xa803]
> [ 1.658139] pci 0000:00:1f.5: reg 20 io port: [0xa480-0xa48f]
> [ 1.658144] pci 0000:00:1f.5: reg 24 io port: [0xa400-0xa40f]
> [ 1.658220] pci 0000:02:00.0: reg 10 32bit mmio: [0xfa000000-0xfaffffff]
> [ 1.658227] pci 0000:02:00.0: reg 14 64bit mmio pref: [0xd0000000-0xdfffffff]
> [ 1.658235] pci 0000:02:00.0: reg 1c 64bit mmio: [0xf8000000-0xf9ffffff]
> [ 1.658239] pci 0000:02:00.0: reg 24 io port: [0xcc00-0xcc7f]
> [ 1.658244] pci 0000:02:00.0: reg 30 32bit mmio pref: [0xfb480000-0xfb4fffff]
> [ 1.658290] pci 0000:00:03.0: bridge io port: [0xc000-0xcfff]
> [ 1.658292] pci 0000:00:03.0: bridge 32bit mmio: [0xf8000000-0xfb4fffff]
> [ 1.658297] pci 0000:00:03.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
> [ 1.658361] pci 0000:00:1c.0: bridge 64bit mmio pref: [0xf4f00000-0xf4ffffff]
> [ 1.658403] pci 0000:04:00.0: reg 10 io port: [0xd800-0xd8ff]
> [ 1.658421] pci 0000:04:00.0: reg 18 64bit mmio: [0xfb5ff000-0xfb5fffff]
> [ 1.658434] pci 0000:04:00.0: reg 20 64bit mmio pref: [0xf4ef0000-0xf4efffff]
> [ 1.658441] pci 0000:04:00.0: reg 30 32bit mmio pref: [0xfb5c0000-0xfb5dffff]
> [ 1.658477] pci 0000:04:00.0: supports D1 D2
> [ 1.658479] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
> [ 1.658537] pci 0000:04:00.0: PME# disabled
> [ 1.658636] pci 0000:00:1c.2: bridge io port: [0xd000-0xdfff]
> [ 1.658639] pci 0000:00:1c.2: bridge 32bit mmio: [0xfb500000-0xfb5fffff]
> [ 1.658644] pci 0000:00:1c.2: bridge 64bit mmio pref: [0xf4e00000-0xf4efffff]
> [ 1.658674] pci 0000:06:00.0: reg 10 32bit mmio: [0xfb6f8000-0xfb6fffff]
> [ 1.658745] pci 0000:06:01.0: reg 10 32bit mmio: [0x000000-0x000fff]
> [ 1.658763] pci 0000:06:01.0: supports D1 D2
> [ 1.658764] pci 0000:06:01.0: PME# supported from D0 D1 D2 D3hot D3cold
> [ 1.658822] pci 0000:06:01.0: PME# disabled
> [ 1.658913] pci 0000:00:1e.0: transparent bridge
> [ 1.658967] pci 0000:00:1e.0: bridge io port: [0xe000-0xefff]
> [ 1.658970] pci 0000:00:1e.0: bridge 32bit mmio: [0xfb600000-0xfbefffff]
> [ 1.658975] pci 0000:00:1e.0: bridge 64bit mmio pref: [0xf5000000-0xf6ffffff]
> [ 1.659009] pci_bus 0000:00: on NUMA node 0
> [ 1.659013] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> [ 1.659257] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
> [ 1.659352] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
> [ 1.659405] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
> [ 1.659463] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE1._PRT]
> [ 1.659512] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE3._PRT]
> [ 1.659560] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE7._PRT]
> [ 1.684264] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12 14 15)
> [ 1.684761] ACPI: PCI Interrupt Link [LNKB] (IRQs *5)
> [ 1.685008] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12 14 15)
> [ 1.685504] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12 *14 15)
> [ 1.685999] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 14 *15)
> [ 1.686496] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 6 7 10 11 12 14 15)
> [ 1.686991] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 *7 10 11 12 14 15)
> [ 1.687487] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *4 6 7 10 11 12 14 15)
> [ 1.687956] vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none
> [ 1.688028] vgaarb: loaded
> [ 1.688137] SCSI subsystem initialized
> [ 1.688296] libata version 3.00 loaded.
> [ 1.688342] usbcore: registered new interface driver usbfs
> [ 1.688405] usbcore: registered new interface driver hub
> [ 1.688474] usbcore: registered new device driver usb
> [ 1.688618] ACPI: WMI: Mapper loaded
> [ 1.688668] PCI: Using ACPI for IRQ routing
> [ 1.688846] Bluetooth: Core ver 2.15
> [ 1.688916] NET: Registered protocol family 31
> [ 1.688968] Bluetooth: HCI device and connection manager initialized
> [ 1.689024] Bluetooth: HCI socket layer initialized
> [ 1.689076] NET: Registered protocol family 8
> [ 1.689128] NET: Registered protocol family 20
> [ 1.689185] NetLabel: Initializing
> [ 1.689235] NetLabel: domain hash size = 128
> [ 1.689286] NetLabel: protocols = UNLABELED CIPSOv4
> [ 1.689347] NetLabel: unlabeled traffic allowed by default
> [ 1.689424] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
> [ 1.689631] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
> [ 1.750486] Switching to clocksource tsc
> [ 1.751759] pnp: PnP ACPI init
> [ 1.751822] ACPI: bus type pnp registered
> [ 1.754433] pnp: PnP ACPI: found 15 devices
> [ 1.754486] ACPI: ACPI bus type pnp unregistered
> [ 1.754544] system 00:01: iomem range 0xfbf00000-0xfbffffff has been reserved
> [ 1.754602] system 00:01: iomem range 0xfc000000-0xfcffffff has been reserved
> [ 1.754659] system 00:01: iomem range 0xfd000000-0xfdffffff has been reserved
> [ 1.754716] system 00:01: iomem range 0xfe000000-0xfebfffff has been reserved
> [ 1.754773] system 00:01: iomem range 0xfec8a000-0xfec8afff could not be reserved
> [ 1.754843] system 00:01: iomem range 0xfed10000-0xfed10fff has been reserved
> [ 1.754903] system 00:07: ioport range 0x290-0x29f has been reserved
> [ 1.754961] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
> [ 1.755016] system 00:08: ioport range 0x800-0x87f has been reserved
> [ 1.755073] system 00:08: ioport range 0x500-0x57f could not be reserved
> [ 1.755129] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
> [ 1.755186] system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
> [ 1.755243] system 00:08: iomem range 0xfed40000-0xfed8ffff has been reserved
> [ 1.755302] system 00:0b: iomem range 0xffc00000-0xffdfffff has been reserved
> [ 1.755360] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved
> [ 1.755431] system 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
> [ 1.755489] system 00:0d: iomem range 0xe0000000-0xefffffff has been reserved
> [ 1.755548] system 00:0e: iomem range 0x0-0x9ffff could not be reserved
> [ 1.755604] system 00:0e: iomem range 0xc0000-0xcffff has been reserved
> [ 1.755660] system 00:0e: iomem range 0xe0000-0xfffff could not be reserved
> [ 1.755716] system 00:0e: iomem range 0x100000-0xbfefffff could not be reserved
> [ 1.755787] system 00:0e: iomem range 0xfed90000-0xffffffff could not be reserved
> [ 1.760488] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
> [ 1.760543] pci 0000:00:01.0: IO window: disabled
> [ 1.760597] pci 0000:00:01.0: MEM window: disabled
> [ 1.760652] pci 0000:00:01.0: PREFETCH window: disabled
> [ 1.760707] pci 0000:00:03.0: PCI bridge, secondary bus 0000:02
> [ 1.760762] pci 0000:00:03.0: IO window: 0xc000-0xcfff
> [ 1.760818] pci 0000:00:03.0: MEM window: 0xf8000000-0xfb4fffff
> [ 1.761617] pci 0000:00:03.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
> [ 1.761691] pci 0000:00:07.0: PCI bridge, secondary bus 0000:03
> [ 1.761745] pci 0000:00:07.0: IO window: disabled
> [ 1.761800] pci 0000:00:07.0: MEM window: disabled
> [ 1.761854] pci 0000:00:07.0: PREFETCH window: disabled
> [ 1.761909] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:05
> [ 1.761965] pci 0000:00:1c.0: IO window: 0x1000-0x1fff
> [ 1.762021] pci 0000:00:1c.0: MEM window: 0xc0000000-0xc03fffff
> [ 1.762078] pci 0000:00:1c.0: PREFETCH window: 0x000000f4f00000-0x000000f4ffffff
> [ 1.762152] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04
> [ 1.762207] pci 0000:00:1c.2: IO window: 0xd000-0xdfff
> [ 1.762263] pci 0000:00:1c.2: MEM window: 0xfb500000-0xfb5fffff
> [ 1.762320] pci 0000:00:1c.2: PREFETCH window: 0x000000f4e00000-0x000000f4efffff
> [ 1.762399] pci 0000:06:01.0: CardBus bridge, secondary bus 0000:07
> [ 1.762454] pci 0000:06:01.0: IO window: 0x00e000-0x00e0ff
> [ 1.762510] pci 0000:06:01.0: IO window: 0x00e400-0x00e4ff
> [ 1.762568] pci 0000:06:01.0: PREFETCH window: 0xc4000000-0xc7ffffff
> [ 1.762625] pci 0000:06:01.0: MEM window: 0xc8000000-0xcbffffff
> [ 1.762682] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:06
> [ 1.762738] pci 0000:00:1e.0: IO window: 0xe000-0xefff
> [ 1.762794] pci 0000:00:1e.0: MEM window: 0xfb600000-0xfbefffff
> [ 1.762851] pci 0000:00:1e.0: PREFETCH window: 0x000000f5000000-0x000000f6ffffff
> [ 1.762931] pci 0000:00:01.0: setting latency timer to 64
> [ 1.762937] pci 0000:00:03.0: setting latency timer to 64
> [ 1.762944] pci 0000:00:07.0: setting latency timer to 64
> [ 1.762950] pci 0000:00:1c.0: enabling device (0106 -> 0107)
> [ 1.763009] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
> [ 1.763066] pci 0000:00:1c.0: setting latency timer to 64
> [ 1.763074] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
> [ 1.763131] pci 0000:00:1c.2: setting latency timer to 64
> [ 1.763136] pci 0000:00:1e.0: setting latency timer to 64
> [ 1.763143] pci 0000:06:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
> [ 1.763203] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
> [ 1.763204] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
> [ 1.763206] pci_bus 0000:02: resource 0 io: [0xc000-0xcfff]
> [ 1.763208] pci_bus 0000:02: resource 1 mem: [0xf8000000-0xfb4fffff]
> [ 1.763209] pci_bus 0000:02: resource 2 pref mem [0xd0000000-0xdfffffff]
> [ 1.763211] pci_bus 0000:05: resource 0 io: [0x1000-0x1fff]
> [ 1.763213] pci_bus 0000:05: resource 1 mem: [0xc0000000-0xc03fffff]
> [ 1.763214] pci_bus 0000:05: resource 2 pref mem [0xf4f00000-0xf4ffffff]
> [ 1.763216] pci_bus 0000:04: resource 0 io: [0xd000-0xdfff]
> [ 1.763218] pci_bus 0000:04: resource 1 mem: [0xfb500000-0xfb5fffff]
> [ 1.763219] pci_bus 0000:04: resource 2 pref mem [0xf4e00000-0xf4efffff]
> [ 1.763221] pci_bus 0000:06: resource 0 io: [0xe000-0xefff]
> [ 1.763222] pci_bus 0000:06: resource 1 mem: [0xfb600000-0xfbefffff]
> [ 1.763224] pci_bus 0000:06: resource 2 pref mem [0xf5000000-0xf6ffffff]
> [ 1.763225] pci_bus 0000:06: resource 3 io: [0x00-0xffff]
> [ 1.763227] pci_bus 0000:06: resource 4 mem: [0x000000-0xffffffffffffffff]
> [ 1.763229] pci_bus 0000:07: resource 0 io: [0xe000-0xe0ff]
> [ 1.763230] pci_bus 0000:07: resource 1 io: [0xe400-0xe4ff]
> [ 1.763232] pci_bus 0000:07: resource 2 pref mem [0xc4000000-0xc7ffffff]
> [ 1.763233] pci_bus 0000:07: resource 3 mem: [0xc8000000-0xcbffffff]
> [ 1.763258] NET: Registered protocol family 2
> [ 1.763380] IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
> [ 1.763962] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
> [ 1.764625] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
> [ 1.764814] TCP: Hash tables configured (established 262144 bind 65536)
> [ 1.764870] TCP reno registered
> [ 1.764987] NET: Registered protocol family 1
> [ 1.765187] pci 0000:02:00.0: Boot video device
> [ 1.765224] Trying to unpack rootfs image as initramfs...
> [ 1.891482] Freeing initrd memory: 7709k freed
> [ 1.892896] Scanning for low memory corruption every 60 seconds
> [ 1.893034] audit: initializing netlink socket (disabled)
> [ 1.893096] type=2000 audit(1257354651.780:1): initialized
> [ 1.896800] HugeTLB registered 2 MB page size, pre-allocated 0 pages
> [ 1.897814] VFS: Disk quotas dquot_6.5.2
> [ 1.897912] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
> [ 1.898380] fuse init (API version 7.13)
> [ 1.898484] msgmni has been set to 24021
> [ 1.898725] alg: No test for stdrng (krng)
> [ 1.898783] io scheduler noop registered
> [ 1.898834] io scheduler anticipatory registered
> [ 1.898887] io scheduler deadline registered
> [ 1.898948] io scheduler cfq registered (default)
> [ 1.899099] pcieport 0000:00:01.0: irq 48 for MSI/MSI-X
> [ 1.899106] pcieport 0000:00:01.0: setting latency timer to 64
> [ 1.899198] pcieport 0000:00:03.0: irq 49 for MSI/MSI-X
> [ 1.899203] pcieport 0000:00:03.0: setting latency timer to 64
> [ 1.899291] pcieport 0000:00:07.0: irq 50 for MSI/MSI-X
> [ 1.899296] pcieport 0000:00:07.0: setting latency timer to 64
> [ 1.899382] pcieport 0000:00:1c.0: irq 51 for MSI/MSI-X
> [ 1.899389] pcieport 0000:00:1c.0: setting latency timer to 64
> [ 1.899481] pcieport 0000:00:1c.2: irq 52 for MSI/MSI-X
> [ 1.899488] pcieport 0000:00:1c.2: setting latency timer to 64
> [ 1.899550] aer 0000:00:01.0:pcie02: AER service couldn't init device: no _OSC support
> [ 1.899556] aer 0000:00:03.0:pcie02: AER service couldn't init device: no _OSC support
> [ 1.899560] aer 0000:00:07.0:pcie02: AER service couldn't init device: no _OSC support
> [ 1.899565] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
> [ 1.899677] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
> [ 1.899821] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
> [ 1.899894] ACPI: Power Button [PWRB]
> [ 1.899971] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
> [ 1.900041] ACPI: Power Button [PWRF]
> [ 1.900779] ACPI: SSDT 00000000bf6980c0 00403 (v01 DpgPmm P001Ist 00000011 INTL 20060113)
> [ 1.901312] ACPI: SSDT 00000000bf69a140 003B2 (v01 PmRef P001Cst 00003001 INTL 20060113)
> [ 1.903931] Monitor-Mwait will be used to enter C-1 state
> [ 1.903950] Monitor-Mwait will be used to enter C-2 state
> [ 1.903966] Monitor-Mwait will be used to enter C-3 state
> [ 1.904005] processor LNXCPU:00: registered as cooling_device0
> [ 1.904450] ACPI: SSDT 00000000bf6984d0 00403 (v01 DpgPmm P002Ist 00000012 INTL 20060113)
> [ 1.904915] ACPI: SSDT 00000000bf69a500 00085 (v01 PmRef P002Cst 00003000 INTL 20060113)
> [ 1.907543] processor LNXCPU:01: registered as cooling_device1
> [ 1.907995] ACPI: SSDT 00000000bf6988e0 00403 (v01 DpgPmm P003Ist 00000012 INTL 20060113)
> [ 1.908469] ACPI: SSDT 00000000bf69a590 00085 (v01 PmRef P003Cst 00003000 INTL 20060113)
> [ 1.911096] processor LNXCPU:02: registered as cooling_device2
> [ 1.911552] ACPI: SSDT 00000000bf698cf0 00403 (v01 DpgPmm P004Ist 00000012 INTL 20060113)
> [ 1.912027] ACPI: SSDT 00000000bf69a620 00085 (v01 PmRef P004Cst 00003000 INTL 20060113)
> [ 1.914645] processor LNXCPU:03: registered as cooling_device3
> [ 1.915099] ACPI: SSDT 00000000bf699100 00403 (v01 DpgPmm P005Ist 00000012 INTL 20060113)
> [ 1.915568] ACPI: SSDT 00000000bf69a6b0 00085 (v01 PmRef P005Cst 00003000 INTL 20060113)
> [ 1.918189] processor LNXCPU:04: registered as cooling_device4
> [ 1.918648] ACPI: SSDT 00000000bf699510 00403 (v01 DpgPmm P006Ist 00000012 INTL 20060113)
> [ 1.919126] ACPI: SSDT 00000000bf69a740 00085 (v01 PmRef P006Cst 00003000 INTL 20060113)
> [ 1.921743] processor LNXCPU:05: registered as cooling_device5
> [ 1.922204] ACPI: SSDT 00000000bf699920 00403 (v01 DpgPmm P007Ist 00000012 INTL 20060113)
> [ 1.922689] ACPI: SSDT 00000000bf69a7d0 00085 (v01 PmRef P007Cst 00003000 INTL 20060113)
> [ 1.925315] processor LNXCPU:06: registered as cooling_device6
> [ 1.925763] ACPI: SSDT 00000000bf699d30 00403 (v01 DpgPmm P008Ist 00000012 INTL 20060113)
> [ 1.926237] ACPI: SSDT 00000000bf69a860 00085 (v01 PmRef P008Cst 00003000 INTL 20060113)
> [ 1.928864] processor LNXCPU:07: registered as cooling_device7
> [ 1.931249] XENFS: not registering filesystem on non-xen platform
> [ 1.932027] Linux agpgart interface v0.103
> [ 1.932080] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
> [ 1.932934] brd: module loaded
> [ 1.933258] loop: module loaded
> [ 1.933351] input: Macintosh mouse button emulation as /devices/virtual/input/input2
> [ 1.933507] ata_piix 0000:00:1f.2: version 2.13
> [ 1.933522] ata_piix 0000:00:1f.2: PCI INT B -> GSI 20 (level, low) -> IRQ 20
> [ 1.933581] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
> [ 1.933811] ata_piix 0000:00:1f.2: setting latency timer to 64
> [ 1.933848] scsi0 : ata_piix
> [ 1.933941] scsi1 : ata_piix
> [ 1.935195] ata1: SATA max UDMA/133 cmd 0xa000 ctl 0x9c00 bmdma 0x9480 irq 20
> [ 1.935256] ata2: SATA max UDMA/133 cmd 0x9880 ctl 0x9800 bmdma 0x9488 irq 20
> [ 1.935327] ata_piix 0000:00:1f.5: PCI INT B -> GSI 20 (level, low) -> IRQ 20
> [ 1.935386] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
> [ 1.935612] ata_piix 0000:00:1f.5: setting latency timer to 64
> [ 1.935636] scsi2 : ata_piix
> [ 1.935715] scsi3 : ata_piix
> [ 1.936749] ata3: SATA max UDMA/133 cmd 0xb000 ctl 0xac00 bmdma 0xa480 irq 20
> [ 1.936808] ata4: SATA max UDMA/133 cmd 0xa880 ctl 0xa800 bmdma 0xa488 irq 20
> [ 1.937235] Fixed MDIO Bus: probed
> [ 1.937287] PPP generic driver version 2.4.2
> [ 1.937389] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [ 1.937458] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
> [ 1.937524] ehci_hcd 0000:00:1a.7: setting latency timer to 64
> [ 1.937527] ehci_hcd 0000:00:1a.7: EHCI Host Controller
> [ 1.937606] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
> [ 1.937693] ehci_hcd 0000:00:1a.7: debug port 1
> [ 1.941631] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
> [ 1.941641] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf7fff000
> [ 1.964967] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
> [ 1.965077] usb usb1: configuration #1 chosen from 1 choice
> [ 1.965148] hub 1-0:1.0: USB hub found
> [ 1.965201] hub 1-0:1.0: 6 ports detected
> [ 1.965296] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
> [ 1.965360] ehci_hcd 0000:00:1d.7: setting latency timer to 64
> [ 1.965362] ehci_hcd 0000:00:1d.7: EHCI Host Controller
> [ 1.965433] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
> [ 1.965519] ehci_hcd 0000:00:1d.7: debug port 1
> [ 1.969454] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
> [ 1.969463] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf7ffe000
> [ 1.994950] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
> [ 1.995047] usb usb2: configuration #1 chosen from 1 choice
> [ 1.995115] hub 2-0:1.0: USB hub found
> [ 1.995168] hub 2-0:1.0: 6 ports detected
> [ 1.995257] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> [ 1.995321] uhci_hcd: USB Universal Host Controller Interface driver
> [ 1.995411] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
> [ 1.995471] uhci_hcd 0000:00:1a.0: setting latency timer to 64
> [ 1.995473] uhci_hcd 0000:00:1a.0: UHCI Host Controller
> [ 1.995547] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
> [ 1.995642] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000b800
> [ 1.995744] usb usb3: configuration #1 chosen from 1 choice
> [ 1.995812] hub 3-0:1.0: USB hub found
> [ 1.995865] hub 3-0:1.0: 2 ports detected
> [ 1.995947] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
> [ 1.996007] uhci_hcd 0000:00:1a.1: setting latency timer to 64
> [ 1.996009] uhci_hcd 0000:00:1a.1: UHCI Host Controller
> [ 1.996079] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
> [ 1.996174] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000b880
> [ 1.996272] usb usb4: configuration #1 chosen from 1 choice
> [ 1.996341] hub 4-0:1.0: USB hub found
> [ 1.996393] hub 4-0:1.0: 2 ports detected
> [ 1.996474] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
> [ 1.996533] uhci_hcd 0000:00:1a.2: setting latency timer to 64
> [ 1.996536] uhci_hcd 0000:00:1a.2: UHCI Host Controller
> [ 1.996605] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
> [ 1.996698] uhci_hcd 0000:00:1a.2: irq 19, io base 0x0000bc00
> [ 1.996798] usb usb5: configuration #1 chosen from 1 choice
> [ 1.996867] hub 5-0:1.0: USB hub found
> [ 1.996919] hub 5-0:1.0: 2 ports detected
> [ 1.997002] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
> [ 1.997062] uhci_hcd 0000:00:1d.0: setting latency timer to 64
> [ 1.997064] uhci_hcd 0000:00:1d.0: UHCI Host Controller
> [ 1.997134] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
> [ 1.997222] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000b080
> [ 1.997321] usb usb6: configuration #1 chosen from 1 choice
> [ 1.997388] hub 6-0:1.0: USB hub found
> [ 1.997441] hub 6-0:1.0: 2 ports detected
> [ 1.997521] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
> [ 1.997580] uhci_hcd 0000:00:1d.1: setting latency timer to 64
> [ 1.997582] uhci_hcd 0000:00:1d.1: UHCI Host Controller
> [ 1.998395] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
> [ 1.998484] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b400
> [ 1.998584] usb usb7: configuration #1 chosen from 1 choice
> [ 1.998652] hub 7-0:1.0: USB hub found
> [ 1.998706] hub 7-0:1.0: 2 ports detected
> [ 1.998786] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
> [ 1.998845] uhci_hcd 0000:00:1d.2: setting latency timer to 64
> [ 1.998848] uhci_hcd 0000:00:1d.2: UHCI Host Controller
> [ 1.998921] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
> [ 1.999009] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b480
> [ 1.999112] usb usb8: configuration #1 chosen from 1 choice
> [ 1.999180] hub 8-0:1.0: USB hub found
> [ 1.999233] hub 8-0:1.0: 2 ports detected
> [ 1.999344] PNP: No PS/2 controller found. Probing ports directly.
> [ 2.001923] serio: i8042 KBD port at 0x60,0x64 irq 1
> [ 2.001983] serio: i8042 AUX port at 0x60,0x64 irq 12
> [ 2.002077] mice: PS/2 mouse device common for all mice
> [ 2.002173] Driver 'rtc_cmos' needs updating - please use bus_type methods
> [ 2.002244] rtc_cmos 00:03: RTC can wake from S4
> [ 2.002315] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
> [ 2.002391] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
> [ 2.002531] device-mapper: uevent: version 1.0.3
> [ 2.002632] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: [email protected]
> [ 2.002793] device-mapper: multipath: version 1.1.0 loaded
> [ 2.002857] device-mapper: multipath round-robin: version 1.0.0 loaded
> [ 2.003256] cpuidle: using governor ladder
> [ 2.003551] cpuidle: using governor menu
> [ 2.003897] TCP cubic registered
> [ 2.004033] NET: Registered protocol family 10
> [ 2.004429] lo: Disabled Privacy Extensions
> [ 2.004705] NET: Registered protocol family 17
> [ 2.004767] Bluetooth: L2CAP ver 2.14
> [ 2.004817] Bluetooth: L2CAP socket layer initialized
> [ 2.004871] Bluetooth: SCO (Voice Link) ver 0.6
> [ 2.004923] Bluetooth: SCO socket layer initialized
> [ 2.005015] Bluetooth: RFCOMM TTY layer initialized
> [ 2.005070] Bluetooth: RFCOMM socket layer initialized
> [ 2.005123] Bluetooth: RFCOMM ver 1.11
> [ 2.009780] PM: Resume from disk failed.
> [ 2.009787] registered taskstats version 1
> [ 2.010229] Magic number: 1:749:187
> [ 2.010394] rtc_cmos 00:03: setting system clock to 2009-11-04 17:10:52 UTC (1257354652)
> [ 2.010469] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
> [ 2.010523] EDD information not available.
> [ 2.291460] ata3: SATA link down (SStatus 0 SControl 300)
> [ 2.440581] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 2.460932] ata4.00: ATA-7: SAMSUNG HD103UJ, 1AA01118, max UDMA7
> [ 2.460995] ata4.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
> [ 2.480924] ata4.00: configured for UDMA/133
> [ 2.624790] usb 3-2: new low speed USB device using uhci_hcd and address 2
> [ 2.790398] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> [ 2.790473] ata1.01: SATA link down (SStatus 0 SControl 300)
> [ 2.790539] ata1.01: link offline, clearing class 3 to NONE
> [ 2.790702] ata2.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 2.790766] ata2.01: SATA link down (SStatus 0 SControl 300)
> [ 2.810800] ata1.00: ATAPI: TSSTcorp CDDVDW SH-S223B, SB01, max UDMA/100
> [ 2.810907] ata2.00: ATA-7: SAMSUNG HD154UI, 1AG01118, max UDMA7
> [ 2.810963] ata2.00: 2930277168 sectors, multi 16: LBA48 NCQ (depth 0/32)
> [ 2.813565] usb 3-2: configuration #1 chosen from 1 choice
> [ 2.830794] ata2.00: configured for UDMA/133
> [ 2.850545] ata1.00: configured for UDMA/100
> [ 2.851842] scsi 0:0:0:0: CD-ROM TSSTcorp CDDVDW SH-S223B SB01 PQ: 0 ANSI: 5
> [ 2.855851] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
> [ 2.855930] Uniform CD-ROM driver Revision: 3.20
> [ 2.856045] sr 0:0:0:0: Attached scsi CD-ROM sr0
> [ 2.856072] sr 0:0:0:0: Attached scsi generic sg0 type 5
> [ 2.856276] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD154UI 1AG0 PQ: 0 ANSI: 5
> [ 2.856443] sd 1:0:0:0: Attached scsi generic sg1 type 0
> [ 2.856600] sd 1:0:0:0: [sda] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
> [ 2.856643] scsi 3:0:0:0: Direct-Access ATA SAMSUNG HD103UJ 1AA0 PQ: 0 ANSI: 5
> [ 2.856705] sd 3:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
> [ 2.856732] sd 3:0:0:0: [sdb] Write Protect is off
> [ 2.856733] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> [ 2.856748] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 2.856819] sdb:
> [ 2.856918] sd 3:0:0:0: Attached scsi generic sg2 type 0
> [ 2.857085] sd 1:0:0:0: [sda] Write Protect is off
> [ 2.857141] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 2.857155] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 2.857297] sda: unknown partition table
> [ 2.867728] sd 1:0:0:0: [sda] Attached SCSI disk
> [ 2.867991] sdb1 sdb2 < sdb5 >
> [ 2.890655] sd 3:0:0:0: [sdb] Attached SCSI disk
> [ 2.890764] Freeing unused kernel memory: 540k freed
> [ 2.890902] Write protecting the kernel read-only data: 7552k
> [ 2.960902] Floppy drive(s): fd0 is 1.44M
> [ 2.966532] usbcore: registered new interface driver hiddev
> [ 2.969771] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
> [ 2.969849] r8169 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
> [ 2.969997] r8169 0000:04:00.0: setting latency timer to 64
> [ 2.970049] r8169 0000:04:00.0: irq 53 for MSI/MSI-X
> [ 2.970576] eth0: RTL8168c/8111c at 0xffffc9000007e000, 00:24:8c:a7:6e:2d, XID 1c4000c0 IRQ 53
> [ 2.976467] FDC 0 is a post-1991 82077
> [ 2.985611] input: Cherry GmbH Cherry TouchBoard as /devices/pci0000:00/0000:00:1a.0/usb3/3-2/3-2:1.0/input/input3
> [ 2.985723] generic-usb 0003:046A:002F.0001: input,hidraw0: USB HID v1.11 Keyboard [Cherry GmbH Cherry TouchBoard] on usb-0000:00:1a.0-2/input0
> [ 3.010571] input: Cherry GmbH Cherry TouchBoard as /devices/pci0000:00/0000:00:1a.0/usb3/3-2/3-2:1.1/input/input4
> [ 3.010689] generic-usb 0003:046A:002F.0002: input,hidraw1: USB HID v1.11 Mouse [Cherry GmbH Cherry TouchBoard] on usb-0000:00:1a.0-2/input1
> [ 3.010780] usbcore: registered new interface driver usbhid
> [ 3.010880] usbhid: v2.6:USB HID core driver
> [ 3.140904] usb 6-2: new full speed USB device using uhci_hcd and address 2
> [ 3.324942] usb 6-2: configuration #1 chosen from 1 choice
> [ 4.079158] PM: Starting manual resume from disk
> [ 4.079161] PM: Resume from partition 8:21
> [ 4.079162] PM: Checking hibernation image.
> [ 4.079367] PM: Error -22 checking image file
> [ 4.079370] PM: Resume from disk failed.
> [ 4.142309] EXT4-fs (sdb1): mounted filesystem with ordered data mode
> [ 6.625698] Adding 2000052k swap on /dev/sdb5. Priority:-1 extents:1 across:2000052k
> [ 7.849284] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
> [ 7.855346] SGI XFS Quota Management subsystem
> [ 7.886584] XFS mounting filesystem sda
> [ 8.020792] Ending clean XFS mount for filesystem: sda
> [ 8.823748] udev: starting version 147
> [ 9.710498] nvidia: module license 'NVIDIA' taints kernel.
> [ 9.710501] Disabling lock debugging due to kernel taint
> [ 10.156989] cfg80211: Calling CRDA to update world regulatory domain
> [ 10.171979] yenta_cardbus 0000:06:01.0: CardBus bridge found [1524:1410]
> [ 10.171997] yenta_cardbus 0000:06:01.0: Using CSCINT to route CSC interrupts to PCI
> [ 10.171999] yenta_cardbus 0000:06:01.0: Routing CardBus interrupts to PCI
> [ 10.172004] yenta_cardbus 0000:06:01.0: TI: mfunc 0x00001002, devctl 0x44
> [ 10.173900] nvidia 0000:02:00.0: PCI INT A -> GSI 24 (level, low) -> IRQ 24
> [ 10.173905] nvidia 0000:02:00.0: setting latency timer to 64
> [ 10.174023] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 185.18.36 Fri Aug 14 17:35:21 PDT 2009
> [ 10.418185] yenta_cardbus 0000:06:01.0: ISA IRQ mask 0x0000, PCI irq 17
> [ 10.418188] yenta_cardbus 0000:06:01.0: Socket status: 30000020
> [ 10.418191] pci_bus 0000:06: Raising subordinate bus# of parent bus (#06) from #07 to #0a
> [ 10.418196] yenta_cardbus 0000:06:01.0: pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff
> [ 10.418198] yenta_cardbus 0000:06:01.0: pcmcia: parent PCI bridge Memory window: 0xfb600000 - 0xfbefffff
> [ 10.418200] yenta_cardbus 0000:06:01.0: pcmcia: parent PCI bridge Memory window: 0xf5000000 - 0xf6ffffff
> [ 10.540799] lp: driver loaded but no devices found
> [ 10.942281] rt61pci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
> [ 10.949231] phy0 -> rt61pci_validate_eeprom: EEPROM recovery - NIC: 0xff80
> [ 10.949233] phy0 -> rt61pci_validate_eeprom: EEPROM recovery - Led: 0xe0ff
> [ 10.949235] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 0302, rf: 0003, rev: 0002561c.
> [ 10.961990] ip_tables: (C) 2000-2006 Netfilter Core Team
> [ 11.048748] cfg80211: World regulatory domain updated:
> [ 11.048750] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
> [ 11.048751] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
> [ 11.048753] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
> [ 11.048755] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
> [ 11.048756] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
> [ 11.048758] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
> [ 11.081556] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
> [ 11.081584] pci 0000:07:00.0: reg 10 32bit mmio: [0x000000-0x00ffff]
> [ 11.081645] yenta_cardbus 0000:06:01.0: EnE: chaning testregister 0xC9, 0e -> 0c
> [ 11.210391] phy0: Selected rate control algorithm 'minstrel'
> [ 11.210928] Registered led device: rt61pci-phy0::radio
> [ 11.210966] Registered led device: rt61pci-phy0::assoc
> [ 11.426723] usbcore: registered new interface driver snd-usb-audio
> [ 11.427862] coretemp coretemp.0: Unable to access MSR 0xEE, for Tjmax, left at default
> [ 11.427898] coretemp coretemp.1: Unable to access MSR 0xEE, for Tjmax, left at default
> [ 11.427991] coretemp coretemp.2: Unable to access MSR 0xEE, for Tjmax, left at default
> [ 11.428087] coretemp coretemp.3: Unable to access MSR 0xEE, for Tjmax, left at default
> [ 11.428125] coretemp coretemp.4: Unable to access MSR 0xEE, for Tjmax, left at default
> [ 11.428157] coretemp coretemp.5: Unable to access MSR 0xEE, for Tjmax, left at default
> [ 11.428184] coretemp coretemp.6: Unable to access MSR 0xEE, for Tjmax, left at default
> [ 11.428271] coretemp coretemp.7: Unable to access MSR 0xEE, for Tjmax, left at default
> [ 11.441678] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
> [ 11.441852] HDA Intel 0000:00:1b.0: setting latency timer to 64
> [ 11.484954] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
> [ 11.485278] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
> [ 11.485280] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
> [ 11.485281] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
> [ 11.513347] RME Hammerfall DSP 0000:07:00.0: enabling device (0000 -> 0002)
> [ 11.513353] RME Hammerfall DSP 0000:07:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
> [ 11.603683] hda_codec: ALC1200: BIOS auto-probing.
> [ 13.389405] ip6_tables: (C) 2000-2006 Netfilter Core Team
> [ 13.986143] Hammerfall-DSP: Firmware already present, initializing card.
> [ 15.184533] r8169: eth0: link down
> [ 15.185650] ADDRCONF(NETDEV_UP): eth0: link is not ready
> [ 15.387562] phy0 -> rt2x00lib_request_firmware: Info - Loading firmware file 'rt2561.bin'.
> [ 15.387565] rt61pci 0000:06:00.0: firmware: requesting rt2561.bin
> [ 15.544241] phy0 -> rt2x00lib_request_firmware: Info - Firmware detected - version: 0.8.
> [ 15.676621] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 102.
> [ 15.676628] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 4, CWmax: 5, Aifs: 2, TXop: 188.
> [ 15.676634] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 3, TXop: 0.
> [ 15.676640] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 7, TXop: 0.
> [ 15.677679] ADDRCONF(NETDEV_UP): wlan0: link is not ready
> [ 25.297686] ppdev: user-space parallel port driver
> [ 28.107305] CPU0 attaching NULL sched-domain.
> [ 28.107309] CPU1 attaching NULL sched-domain.
> [ 28.107310] CPU2 attaching NULL sched-domain.
> [ 28.107312] CPU3 attaching NULL sched-domain.
> [ 28.107313] CPU4 attaching NULL sched-domain.
> [ 28.107314] CPU5 attaching NULL sched-domain.
> [ 28.107316] CPU6 attaching NULL sched-domain.
> [ 28.107317] CPU7 attaching NULL sched-domain.
> [ 28.190785] CPU0 attaching sched-domain:
> [ 28.190787] domain 0: span 0,4 level SIBLING
> [ 28.190789] groups: 0 (cpu_power = 589) 4 (cpu_power = 589)
> [ 28.190792] domain 1: span 0-7 level MC
> [ 28.190794] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178)
> [ 28.190800] CPU1 attaching sched-domain:
> [ 28.190801] domain 0: span 1,5 level SIBLING
> [ 28.190802] groups: 1 (cpu_power = 589) 5 (cpu_power = 589)
> [ 28.190805] domain 1: span 0-7 level MC
> [ 28.190806] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178)
> [ 28.190812] CPU2 attaching sched-domain:
> [ 28.190813] domain 0: span 2,6 level SIBLING
> [ 28.190814] groups: 2 (cpu_power = 589) 6 (cpu_power = 589)
> [ 28.190817] domain 1: span 0-7 level MC
> [ 28.190818] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178)
> [ 28.190823] CPU3 attaching sched-domain:
> [ 28.190824] domain 0: span 3,7 level SIBLING
> [ 28.190826] groups: 3 (cpu_power = 589) 7 (cpu_power = 589)
> [ 28.190829] domain 1: span 0-7 level MC
> [ 28.190830] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178)
> [ 28.190835] CPU4 attaching sched-domain:
> [ 28.190836] domain 0: span 0,4 level SIBLING
> [ 28.190837] groups: 4 (cpu_power = 589) 0 (cpu_power = 589)
> [ 28.190840] domain 1: span 0-7 level MC
> [ 28.190842] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178)
> [ 28.190847] CPU5 attaching sched-domain:
> [ 28.190848] domain 0: span 1,5 level SIBLING
> [ 28.190849] groups: 5 (cpu_power = 589) 1 (cpu_power = 589)
> [ 28.190852] domain 1: span 0-7 level MC
> [ 28.190853] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178)
> [ 28.190859] CPU6 attaching sched-domain:
> [ 28.190860] domain 0: span 2,6 level SIBLING
> [ 28.190861] groups: 6 (cpu_power = 589) 2 (cpu_power = 589)
> [ 28.190864] domain 1: span 0-7 level MC
> [ 28.190865] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178)
> [ 28.190870] CPU7 attaching sched-domain:
> [ 28.190871] domain 0: span 3,7 level SIBLING
> [ 28.190873] groups: 7 (cpu_power = 589) 3 (cpu_power = 589)
> [ 28.190876] domain 1: span 0-7 level MC
> [ 28.190877] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178)
> [ 86.409045] wlan0: deauthenticating from 00:24:fe:09:94:18 by local choice (reason=3)
> [ 86.409209] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 1)
> [ 86.412957] wlan0: direct probe responded
> [ 86.412962] wlan0: authenticate with AP 00:24:fe:09:94:18 (try 1)
> [ 86.416343] wlan0: authenticated
> [ 86.416361] wlan0: associate with AP 00:24:fe:09:94:18 (try 1)
> [ 86.419280] wlan0: RX AssocResp from 00:24:fe:09:94:18 (capab=0x401 status=0 aid=2)
> [ 86.419282] wlan0: associated
> [ 86.420465] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
> [ 88.872600] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2.
> [ 88.872604] Please file bug report to http://rt2x00.serialmonkey.com.
> [ 97.096637] wlan0: no IPv6 routers present
> [ 631.853445] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 631.853456] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 631.853466] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 631.853475] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 631.929711] wlan0: deauthenticating from 00:24:fe:09:94:18 by local choice (reason=3)
> [ 631.929750] wlan0: deauthenticating from 00:24:fe:09:94:18 by local choice (reason=3)
> [ 631.948559] wlan0: direct probe to AP 00:14:6c:5a:96:60 (try 1)
> [ 631.950289] wlan0: direct probe responded
> [ 631.950293] wlan0: authenticate with AP 00:14:6c:5a:96:60 (try 1)
> [ 631.954044] wlan0: authenticated
> [ 631.991386] wlan0: associate with AP 00:14:6c:5a:96:60 (try 1)
> [ 631.993618] wlan0: RX ReassocResp from 00:14:6c:5a:96:60 (capab=0x401 status=0 aid=1)
> [ 631.993622] wlan0: associated
> [ 631.993934] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 631.993942] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 631.993950] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 631.993958] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 677.910672] wlan0: deauthenticated from 00:14:6c:5a:96:60 (Reason: 7)
> [ 677.910685] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 677.910693] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 677.910701] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 677.910709] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 679.458583] wlan0: deauthenticating from 00:14:6c:5a:96:60 by local choice (reason=3)
> [ 679.478323] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 1)
> [ 679.480351] wlan0: direct probe responded
> [ 679.480355] wlan0: authenticate with AP 00:24:fe:09:94:18 (try 1)
> [ 679.482828] wlan0: authenticated
> [ 679.482848] wlan0: associate with AP 00:24:fe:09:94:18 (try 1)
> [ 679.485996] wlan0: RX ReassocResp from 00:24:fe:09:94:18 (capab=0x401 status=0 aid=2)
> [ 679.486000] wlan0: associated
> [ 871.756709] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 871.756719] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 871.756726] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 871.756734] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 871.834625] wlan0: deauthenticating from 00:24:fe:09:94:18 by local choice (reason=3)
> [ 871.834666] wlan0: deauthenticating from 00:24:fe:09:94:18 by local choice (reason=3)
> [ 871.854802] wlan0: direct probe to AP 00:14:6c:5a:96:60 (try 1)
> [ 871.856453] wlan0: direct probe responded
> [ 871.856457] wlan0: authenticate with AP 00:14:6c:5a:96:60 (try 1)
> [ 871.858184] wlan0: authenticated
> [ 871.896378] wlan0: associate with AP 00:14:6c:5a:96:60 (try 1)
> [ 871.898260] wlan0: RX ReassocResp from 00:14:6c:5a:96:60 (capab=0x401 status=0 aid=1)
> [ 871.898264] wlan0: associated
> [ 871.898875] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 871.898909] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 871.898919] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 871.898929] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 917.819830] wlan0: deauthenticated from 00:14:6c:5a:96:60 (Reason: 7)
> [ 917.819843] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 917.819851] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 917.819859] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 917.819866] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 919.366662] wlan0: deauthenticating from 00:14:6c:5a:96:60 by local choice (reason=3)
> [ 919.389718] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 1)
> [ 919.586979] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 2)
> [ 919.786869] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 3)
> [ 919.986197] wlan0: direct probe to AP 00:24:fe:09:94:18 timed out
> [ 925.773981] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 1)
> [ 925.775992] wlan0: direct probe responded
> [ 925.775996] wlan0: authenticate with AP 00:24:fe:09:94:18 (try 1)
> [ 925.778936] wlan0: authenticated
> [ 925.778955] wlan0: associate with AP 00:24:fe:09:94:18 (try 1)
> [ 925.781540] wlan0: RX ReassocResp from 00:24:fe:09:94:18 (capab=0x401 status=0 aid=2)
> [ 925.781543] wlan0: associated
> [ 991.710855] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 991.710864] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 991.710873] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 991.710880] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 991.833019] wlan0: deauthenticating from 00:24:fe:09:94:18 by local choice (reason=3)
> [ 991.833059] wlan0: deauthenticating from 00:24:fe:09:94:18 by local choice (reason=3)
> [ 991.853052] wlan0: direct probe to AP 00:14:6c:5a:96:60 (try 1)
> [ 991.854656] wlan0: direct probe responded
> [ 991.854661] wlan0: authenticate with AP 00:14:6c:5a:96:60 (try 1)
> [ 991.856415] wlan0: authenticated
> [ 991.894763] wlan0: associate with AP 00:14:6c:5a:96:60 (try 1)
> [ 991.902095] wlan0: RX ReassocResp from 00:14:6c:5a:96:60 (capab=0x401 status=0 aid=1)
> [ 991.902100] wlan0: associated
> [ 991.902605] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 991.902613] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 991.902621] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 991.902629] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 1037.776170] wlan0: deauthenticated from 00:14:6c:5a:96:60 (Reason: 7)
> [ 1037.776183] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 1037.776192] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 1037.776199] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 1037.776207] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 1039.320831] wlan0: deauthenticating from 00:14:6c:5a:96:60 by local choice (reason=3)
> [ 1039.340475] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 1)
> [ 1039.342469] wlan0: direct probe responded
> [ 1039.342473] wlan0: authenticate with AP 00:24:fe:09:94:18 (try 1)
> [ 1039.345279] wlan0: authenticated
> [ 1039.345299] wlan0: associate with AP 00:24:fe:09:94:18 (try 1)
> [ 1039.347910] wlan0: RX ReassocResp from 00:24:fe:09:94:18 (capab=0x401 status=0 aid=2)
> [ 1039.347914] wlan0: associated
> [ 1111.666903] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 1111.666912] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 1111.666921] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 1111.666928] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 1111.743367] wlan0: deauthenticating from 00:24:fe:09:94:18 by local choice (reason=3)
> [ 1111.743408] wlan0: deauthenticating from 00:24:fe:09:94:18 by local choice (reason=3)
> [ 1111.763503] wlan0: direct probe to AP 00:14:6c:5a:96:60 (try 1)
> [ 1111.963267] wlan0: direct probe to AP 00:14:6c:5a:96:60 (try 2)
> [ 1111.964988] wlan0: direct probe responded
> [ 1111.964992] wlan0: authenticate with AP 00:14:6c:5a:96:60 (try 1)
> [ 1111.966753] wlan0: authenticated
> [ 1111.966771] wlan0: associate with AP 00:14:6c:5a:96:60 (try 1)
> [ 1111.969096] wlan0: RX ReassocResp from 00:14:6c:5a:96:60 (capab=0x401 status=0 aid=1)
> [ 1111.969099] wlan0: associated
> [ 1111.969454] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 1111.969461] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 1111.969469] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 1111.969477] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 1155.736323] wlan0: deauthenticated from 00:14:6c:5a:96:60 (Reason: 7)
> [ 1155.736335] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 1155.736344] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 1155.736415] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 1155.736424] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 1157.285521] wlan0: deauthenticating from 00:14:6c:5a:96:60 by local choice (reason=3)
> [ 1157.305987] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 1)
> [ 1157.505130] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 2)
> [ 1157.705131] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 3)
> [ 1157.905642] wlan0: direct probe to AP 00:24:fe:09:94:18 timed out
> [ 1163.902756] wlan0: direct probe to AP 00:14:6c:5a:96:60 (try 1)
> [ 1163.904411] wlan0: direct probe responded
> [ 1163.904415] wlan0: authenticate with AP 00:14:6c:5a:96:60 (try 1)
> [ 1163.958044] wlan0: authenticated
> [ 1163.958063] wlan0: associate with AP 00:14:6c:5a:96:60 (try 1)
> [ 1163.962692] wlan0: RX ReassocResp from 00:14:6c:5a:96:60 (capab=0x401 status=0 aid=1)
> [ 1163.962695] wlan0: associated
> [ 1163.963009] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 1163.963017] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 1163.963025] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 1163.963033] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 1217.702957] wlan0: deauthenticated from 00:14:6c:5a:96:60 (Reason: 7)
> [ 1217.702969] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 1217.702977] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 1217.702985] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 1217.702993] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 1219.271545] wlan0: direct probe to AP 00:14:6c:5a:96:60 (try 1)
> [ 1219.273152] wlan0: direct probe responded
> [ 1219.273157] wlan0: authenticate with AP 00:14:6c:5a:96:60 (try 1)
> [ 1219.274939] wlan0: authenticated
> [ 1219.274960] wlan0: associate with AP 00:14:6c:5a:96:60 (try 1)
> [ 1219.277147] wlan0: RX ReassocResp from 00:14:6c:5a:96:60 (capab=0x401 status=0 aid=1)
> [ 1219.277150] wlan0: associated
> [ 1219.277480] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 1219.277488] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 1219.277496] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 1219.277503] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 1457.614602] wlan0: deauthenticated from 00:14:6c:5a:96:60 (Reason: 7)
> [ 1457.614615] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 1457.614623] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 1457.614631] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 1457.614639] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 1459.209592] wlan0: direct probe to AP 00:14:6c:5a:96:60 (try 1)
> [ 1459.211254] wlan0: direct probe responded
> [ 1459.211259] wlan0: authenticate with AP 00:14:6c:5a:96:60 (try 1)
> [ 1459.212978] wlan0: authenticated
> [ 1459.212996] wlan0: associate with AP 00:14:6c:5a:96:60 (try 1)
> [ 1459.215260] wlan0: RX ReassocResp from 00:14:6c:5a:96:60 (capab=0x401 status=0 aid=1)
> [ 1459.215263] wlan0: associated
> [ 1459.215769] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 1459.215777] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 1459.215785] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 1459.215792] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 1471.529821] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 1471.529828] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 1471.529835] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 1471.529841] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 1471.585463] wlan0: deauthenticating from 00:14:6c:5a:96:60 by local choice (reason=3)
> [ 1471.585501] wlan0: deauthenticating from 00:14:6c:5a:96:60 by local choice (reason=3)
> [ 1471.605499] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 1)
> [ 1471.607487] wlan0: direct probe responded
> [ 1471.607490] wlan0: authenticate with AP 00:24:fe:09:94:18 (try 1)
> [ 1471.610845] wlan0: authenticated
> [ 1471.666559] wlan0: associate with AP 00:24:fe:09:94:18 (try 1)
> [ 1471.669919] wlan0: RX ReassocResp from 00:24:fe:09:94:18 (capab=0x401 status=0 aid=2)
> [ 1471.669922] wlan0: associated
> [ 1591.481020] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 1591.481029] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 1591.481037] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 1591.481045] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 1591.562677] wlan0: deauthenticating from 00:24:fe:09:94:18 by local choice (reason=3)
> [ 1591.562722] wlan0: deauthenticating from 00:24:fe:09:94:18 by local choice (reason=3)
> [ 1591.582741] wlan0: direct probe to AP 00:14:6c:5a:96:60 (try 1)
> [ 1591.592157] wlan0: direct probe responded
> [ 1591.592161] wlan0: authenticate with AP 00:14:6c:5a:96:60 (try 1)
> [ 1591.594157] wlan0: authenticated
> [ 1591.624398] wlan0: associate with AP 00:14:6c:5a:96:60 (try 1)
> [ 1591.626246] wlan0: RX ReassocResp from 00:14:6c:5a:96:60 (capab=0x401 status=0 aid=1)
> [ 1591.626249] wlan0: associated
> [ 1591.626628] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 1591.626636] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 1591.626644] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 1591.626652] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 1656.653960] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2.
> [ 1656.653963] Please file bug report to http://rt2x00.serialmonkey.com.
> [ 1755.419796] wlan0: deauthenticated from 00:14:6c:5a:96:60 (Reason: 7)
> [ 1755.419809] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 1755.419817] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 1755.419825] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 1755.419833] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 1756.967256] wlan0: deauthenticating from 00:14:6c:5a:96:60 by local choice (reason=3)
> [ 1756.985669] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 1)
> [ 1756.987739] wlan0: direct probe responded
> [ 1756.987744] wlan0: authenticate with AP 00:24:fe:09:94:18 (try 1)
> [ 1756.990263] wlan0: authenticated
> [ 1756.990282] wlan0: associate with AP 00:24:fe:09:94:18 (try 1)
> [ 1756.993557] wlan0: RX ReassocResp from 00:24:fe:09:94:18 (capab=0x401 status=0 aid=2)
> [ 1756.993561] wlan0: associated
> [ 1759.427571] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2.
> [ 1759.427574] Please file bug report to http://rt2x00.serialmonkey.com.
> [ 1822.420522] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2.
> [ 1822.420524] Please file bug report to http://rt2x00.serialmonkey.com.
> [ 1951.374836] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 1951.374845] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 1951.374873] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 1951.374881] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
> [ 1951.451087] wlan0: deauthenticating from 00:24:fe:09:94:18 by local choice (reason=3)
> [ 1951.451126] wlan0: deauthenticating from 00:24:fe:09:94:18 by local choice (reason=3)
> [ 1951.471202] wlan0: direct probe to AP 00:14:6c:5a:96:60 (try 1)
> [ 1951.670923] wlan0: direct probe to AP 00:14:6c:5a:96:60 (try 2)
> [ 1951.672651] wlan0: direct probe responded
> [ 1951.672655] wlan0: authenticate with AP 00:14:6c:5a:96:60 (try 1)
> [ 1951.674408] wlan0: authenticated
> [ 1951.674427] wlan0: associate with AP 00:14:6c:5a:96:60 (try 1)
> [ 1951.676580] wlan0: RX ReassocResp from 00:14:6c:5a:96:60 (capab=0x401 status=0 aid=1)
> [ 1951.676583] wlan0: associated
> [ 1951.677126] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
> [ 1951.677134] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
> [ 1951.677142] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
> [ 1951.677150] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
--
John W. Linville Someday the world will need a hero, and you
[email protected] might be all we have. Be ready.
> Could you please try a bisect between 2.6.31 and 2.6.32-rc5? That
> should reveal the faulty commit.
can you give me some hints, which source files, i should pay attention to?
thnx, tim
--
[email protected]
http://tim.klingt.org
The first question I ask myself when something doesn't seem to be
beautiful is why do I think it's not beautiful. And very shortly you
discover that there is no reason.
John Cage.
On 11/29/2009 05:59 PM, Gábor Stefanik wrote:
> On Sun, Nov 29, 2009 at 3:01 PM, Tim Blechmann <[email protected]> wrote:
>> On 11/04/2009 07:00 PM, Tim Blechmann wrote:
>>>> running the rt61pci module on 2.6.31.5 works fine, but using the recent
>>>> linus/master (2.6.32-rc5) results in this:
>>>
>>> same issue with 2.6.32-rc5 ... new bootlog with more debugging info
>>> attached ...
>>
>> i was still able to reproduce this issue with 2.6.32-rc8 ... it would
>> be nice, if someone could have a look into this issue before 2.6.32 is
>> released ...
>>
>> dmesg from 2.6.32-rc8:
>> [ 10.249098] rt61pci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
>> [ 10.257182] phy0 -> rt61pci_validate_eeprom: EEPROM recovery - NIC: 0xff80
>> [ 10.257184] phy0 -> rt61pci_validate_eeprom: EEPROM recovery - Led: 0xe0ff
>> [ 10.257187] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 0302, rf: 0003, rev: 0002561c.
>> [ 10.351794] Registered led device: rt61pci-phy0::radio
>> [ 10.351839] Registered led device: rt61pci-phy0::assoc
>> [ 14.342046] rt61pci 0000:06:00.0: firmware: requesting rt2561.bin
>> [ 14.395533] phy0 -> rt2x00lib_request_firmware: Info - Firmware detected - version: 0.8.
>> [ 14.421238] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 102.
>> [ 14.421245] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 4, CWmax: 5, Aifs: 2, TXop: 188.
>> [ 14.421252] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 3, TXop: 0.
>> [ 14.421258] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 7, TXop: 0.
>> [ 273.404685] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2.
>> [ 273.404687] Please file bug report to http://rt2x00.serialmonkey.com.
>> [ 282.143549] wlan0: no IPv6 routers present
>> [ 357.304908] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 2
>> [ 357.333806] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 9
>> [ 360.172776] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2.
>> [ 360.172778] Please file bug report to http://rt2x00.serialmonkey.com.
>> [ 360.172782] phy0 -> rt2x00mac_tx_rts_cts: Warning - Failed to send RTS/CTS frame.
>> [ 383.880010] No probe response from AP 00:24:fe:09:94:18 after 500ms, disconnecting.
>> [ 383.880026] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
>> [ 383.880034] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
>> [ 383.880042] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
>> [ 383.880050] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
>> [ 385.220460] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 1)
>> [ 385.421337] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 2)
>> [ 385.621304] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 3)
>> [ 385.821264] wlan0: direct probe to AP 00:24:fe:09:94:18 timed out
>>
>>
>> lspci -vvv:
>>
>> 06:00.0 Network controller: RaLink RT2561/RT61 rev B 802.11g
>> Subsystem: D-Link System Inc Device 3c09
>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
>> Latency: 64, Cache Line Size: 64 bytes
>> Interrupt: pin A routed to IRQ 16
>> Region 0: Memory at fb6f8000 (32-bit, non-prefetchable) [size=32K]
>> Capabilities: [40] Power Management version 2
>> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
>> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>> Kernel driver in use: rt61pci
>> Kernel modules: rt61pci
>>
>> thanks, tim
>
> Could you please try a bisect between 2.6.31 and 2.6.32-rc5? That
> should reveal the faulty commit.
unfortunately, this bug seems to be shadowed by another bug, so
bisecting was not really successful ... do you have suggestions for
commits to revert?
the commits touching drivers/net/wireless/rt2x00/* are:
Alexey Dobriyan (1):
headers: remove sched.h from interrupt.h
Andrew Price (1):
rt2x00: fix the definition of rt2x00crypto_rx_insert_iv
Benoit PAPILLAULT (1):
rt2x00: Add support for retry rates
David S. Miller (2):
Merge branch 'master' of master.kernel.org:/.../davem/net-2.6
Merge branch 'master' of master.kernel.org:/.../davem/net-2.6
Igor Perminov (3):
rt2x00: Fix for race condition while update beacon
rt2x00: FIF_PSPOLL filter flag support
rt2x00: Fix beacon de-synchronization while update beacon
Ivo van Doorn (18):
rt2x00: use wiphy rfkill interface
rt2x00: Remove DEVICE_STATE_DISABLED_RADIO_HW
rt2x00: Fix build error when crypto support is disabled
rt2x00: Remove usage of deprecated radio_enabled &
IEEE80211_CONF_CHANGE_RADIO_ENABLED
rt2x00: Use IEEE80211_TX_CTL_MORE_FRAMES flag
rt2x00: Align ieee80211 header to 4-byte boundary for PCI devices
rt2x00: Fix RFKILL polling
rt2x00: Fix for rt2800usb for SHARED_KEY_TABLE initializations
rt2x00: Add new RF chip defines
rt2x00: Set SKBDESC_L2_PADDED in RX path
rt2x00: wireless CLI ID and packet ID must not be 0
rt2x00: Fix MCS register intialization
rt2x00: configure_filter() callback is allowed to sleep
rt2x00: bss_info_changed() callback is allowed to sleep
rt2x00: Cleanup rt2x00mac_bss_info_changed()
rt2x00: Fix TX status reporting
rt2x00: Reorganize padding & L2 padding
rt2x00: Hardcode TX ack timeout and consume time
Johannes Berg (4):
rt2x00: remove skb->do_not_encrypt usage
mac80211: push rx status into skb->cb
wireless: remove print_mac uses
mac80211: allow configure_filter callback to sleep
Lars Ericsson (3):
rt2x00: Don't alter rt2x00dev->default_ant
rt2x00: Fix quality houskeeping for software diversity
rt2x00: Fix rounding errors in RSSI average calculation
Luis Correia (1):
rt2x00: Comment spellchecking
Luis R. Rodriguez (2):
rt2x00: move experimental on kconfig only to rt2800usb
mac80211: redefine usage of the mac80211 workqueue
Michal Szalata (1):
rt2x00: Thrustmaster FunAccess WIFI USB and rt73usb
Pavel Roskin (2):
rt61pci: fix module reloading
rt2x00: cancel all work on disconnect
Stefan Steuerwald (1):
rt2x00: Implement set_tim callback for all drivers
--
[email protected]
http://tim.klingt.org
Which is more musical, a truck passing by a factory or a truck passing
by a music school?
John Cage
On 11/29/2009 05:59 PM, Gábor Stefanik wrote:
> On Sun, Nov 29, 2009 at 3:01 PM, Tim Blechmann <tim-xpEK/[email protected]> wrote:
>> On 11/04/2009 07:00 PM, Tim Blechmann wrote:
>>>> running the rt61pci module on 2.6.31.5 works fine, but using the recent
>>>> linus/master (2.6.32-rc5) results in this:
>>>
>>> same issue with 2.6.32-rc5 ... new bootlog with more debugging info
>>> attached ...
>>
>> i was still able to reproduce this issue with 2.6.32-rc8 ... it would
>> be nice, if someone could have a look into this issue before 2.6.32 is
>> released ...
>>
>> dmesg from 2.6.32-rc8:
>> [ 10.249098] rt61pci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
>> [ 10.257182] phy0 -> rt61pci_validate_eeprom: EEPROM recovery - NIC: 0xff80
>> [ 10.257184] phy0 -> rt61pci_validate_eeprom: EEPROM recovery - Led: 0xe0ff
>> [ 10.257187] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 0302, rf: 0003, rev: 0002561c.
>> [ 10.351794] Registered led device: rt61pci-phy0::radio
>> [ 10.351839] Registered led device: rt61pci-phy0::assoc
>> [ 14.342046] rt61pci 0000:06:00.0: firmware: requesting rt2561.bin
>> [ 14.395533] phy0 -> rt2x00lib_request_firmware: Info - Firmware detected - version: 0.8.
>> [ 14.421238] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 102.
>> [ 14.421245] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 4, CWmax: 5, Aifs: 2, TXop: 188.
>> [ 14.421252] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 3, TXop: 0.
>> [ 14.421258] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 7, TXop: 0.
>> [ 273.404685] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2.
>> [ 273.404687] Please file bug report to http://rt2x00.serialmonkey.com.
>> [ 282.143549] wlan0: no IPv6 routers present
>> [ 357.304908] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 2
>> [ 357.333806] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 9
>> [ 360.172776] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2.
>> [ 360.172778] Please file bug report to http://rt2x00.serialmonkey.com.
>> [ 360.172782] phy0 -> rt2x00mac_tx_rts_cts: Warning - Failed to send RTS/CTS frame.
>> [ 383.880010] No probe response from AP 00:24:fe:09:94:18 after 500ms, disconnecting.
>> [ 383.880026] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.
>> [ 383.880034] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.
>> [ 383.880042] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.
>> [ 383.880050] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
>> [ 385.220460] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 1)
>> [ 385.421337] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 2)
>> [ 385.621304] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 3)
>> [ 385.821264] wlan0: direct probe to AP 00:24:fe:09:94:18 timed out
>>
>>
>> lspci -vvv:
>>
>> 06:00.0 Network controller: RaLink RT2561/RT61 rev B 802.11g
>> Subsystem: D-Link System Inc Device 3c09
>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
>> Latency: 64, Cache Line Size: 64 bytes
>> Interrupt: pin A routed to IRQ 16
>> Region 0: Memory at fb6f8000 (32-bit, non-prefetchable) [size=32K]
>> Capabilities: [40] Power Management version 2
>> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
>> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>> Kernel driver in use: rt61pci
>> Kernel modules: rt61pci
>>
>> thanks, tim
>
> Could you please try a bisect between 2.6.31 and 2.6.32-rc5? That
> should reveal the faulty commit.
>
>>
>> --
>> [email protected]
>> http://tim.klingt.org
>>
>> Happiness is a byproduct of function, purpose, and conflict; those who
>> seek happiness for itself seek victory without war.
>> William S. Burroughs
btw, on v2.6.31.6-rt19, i get the following messages continuously:
[35097.254691] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 15
[35097.352620] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 21
[35097.400820] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 11
[35097.682924] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 17
[35098.050321] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 5
[35098.203187] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 23
[35098.390729] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 15
[35098.572894] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 15
[35098.735895] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 19
[35099.069564] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 7
[35099.407685] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 9
[35099.408726] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 13
[35099.417144] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 17
[35099.420996] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 21
[35099.518701] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 23
[35100.012178] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 11
[35101.354838] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 15
[35101.448263] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 7
[35101.498144] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 13
[35102.168253] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 9
[35102.548745] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 9
what does this tell me? i am not able to get any network connection
with any 2.6.32-rc build, with (and without) the previously posted
error messages
tim
--
[email protected]
http://tim.klingt.org
Who need fossil fuel when the sun ain't goin' nowhere
Amiri Baraka