From: "H. Nikolaus Schaller" <[email protected]>
[ Upstream commit 934df23171e7c5b71d937104d4957891c39748ff ]
1. check if chip is really present and don't succeed if it isn't.
2. if it succeeds, power down the chip until accessed
Signed-off-by: H. Nikolaus Schaller <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/input/touchscreen/tsc2007.c | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/drivers/input/touchscreen/tsc2007.c b/drivers/input/touchscreen/tsc2007.c
index 5d0cd51c6f41..a4b7b4c3d27b 100644
--- a/drivers/input/touchscreen/tsc2007.c
+++ b/drivers/input/touchscreen/tsc2007.c
@@ -455,6 +455,14 @@ static int tsc2007_probe(struct i2c_client *client,
tsc2007_stop(ts);
+ /* power down the chip (TSC2007_SETUP does not ACK on I2C) */
+ err = tsc2007_xfer(ts, PWRDOWN);
+ if (err < 0) {
+ dev_err(&client->dev,
+ "Failed to setup chip: %d\n", err);
+ return err; /* usually, chip does not respond */
+ }
+
err = input_register_device(input_dev);
if (err) {
dev_err(&client->dev,
--
2.14.1
From: Stephane Eranian <[email protected]>
[ Upstream commit 88b897a30c525c2eee6e7f16e1e8d0f18830845e ]
This patch significantly improves the execution time of
perf_event__synthesize_mmap_events() when running perf record on systems
where processes have lots of threads.
It just happens that cat /proc/pid/maps support uses a O(N^2) algorithm to
generate each map line in the maps file. If you have 1000 threads, then you
have necessarily 1000 stacks. For each vma, you need to check if it
corresponds to a thread's stack. With a large number of threads, this can take
a very long time. I have seen latencies >> 10mn.
As of today, perf does not use the fact that a mapping is a stack, therefore we
can work around the issue by using /proc/pid/tasks/pid/maps. This entry does
not try to map a vma to stack and is thus much faster with no loss of
functonality.
The proc-map-timeout logic is kept in case users still want some upper limit.
In V2, we fix the file path from /proc/pid/tasks/pid/maps to actual
/proc/pid/task/pid/maps, tasks -> task. Thanks Arnaldo for catching this.
Committer note:
This problem seems to have been elliminated in the kernel since commit :
b18cb64ead40 ("fs/proc: Stop trying to report thread stacks").
Signed-off-by: Stephane Eranian <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/perf/util/event.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/tools/perf/util/event.c b/tools/perf/util/event.c
index 8ab0d7da956b..663192395780 100644
--- a/tools/perf/util/event.c
+++ b/tools/perf/util/event.c
@@ -255,8 +255,8 @@ int perf_event__synthesize_mmap_events(struct perf_tool *tool,
if (machine__is_default_guest(machine))
return 0;
- snprintf(filename, sizeof(filename), "%s/proc/%d/maps",
- machine->root_dir, pid);
+ snprintf(filename, sizeof(filename), "%s/proc/%d/task/%d/maps",
+ machine->root_dir, pid, pid);
fp = fopen(filename, "r");
if (fp == NULL) {
--
2.14.1
From: Greg KH <[email protected]>
[ Upstream commit 6f051e4a685b768f3704c7c069aa1edee3010622 ]
[resend due to me forgetting to cc: linux-api the first time around I
posted these back on Feb 23]
From: Greg Kroah-Hartman <[email protected]>
When userspace tries to use these defines, it complains that it needs to
be an unsigned 1 that is shifted, so libc implementations have to create
their own version. Fix this by defining it properly so that libcs can
just use the kernel uapi header.
Reported-by: Elliott Hughes <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
include/uapi/linux/eventpoll.h | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/include/uapi/linux/eventpoll.h b/include/uapi/linux/eventpoll.h
index bc96b14dfb2c..f4d5c998cc2b 100644
--- a/include/uapi/linux/eventpoll.h
+++ b/include/uapi/linux/eventpoll.h
@@ -40,7 +40,7 @@
#define EPOLLRDHUP 0x00002000
/* Set exclusive wakeup mode for the target file descriptor */
-#define EPOLLEXCLUSIVE (1 << 28)
+#define EPOLLEXCLUSIVE (1U << 28)
/*
* Request the handling of system wakeup events so as to prevent system suspends
@@ -52,13 +52,13 @@
*
* Requires CAP_BLOCK_SUSPEND
*/
-#define EPOLLWAKEUP (1 << 29)
+#define EPOLLWAKEUP (1U << 29)
/* Set the One Shot behaviour for the target file descriptor */
-#define EPOLLONESHOT (1 << 30)
+#define EPOLLONESHOT (1U << 30)
/* Set the Edge Triggered behaviour for the target file descriptor */
-#define EPOLLET (1 << 31)
+#define EPOLLET (1U << 31)
/*
* On x86-64 make the 64bit structure have the same alignment as the
--
2.14.1
From: Steve Lin <[email protected]>
[ Upstream commit 2f771399a3a2c371c140ff33544a583c6fbc5fd9 ]
Allows the BCMA version of the bgmac driver to obtain MAC address
from the device tree. If no MAC address is specified there, then
the previous behavior (obtaining MAC address from SPROM) is
used.
Signed-off-by: Steve Lin <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Acked-by: Jon Mason <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/broadcom/bgmac-bcma.c | 39 ++++++++++++++++++------------
1 file changed, 23 insertions(+), 16 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bgmac-bcma.c b/drivers/net/ethernet/broadcom/bgmac-bcma.c
index c16ec3a51876..1ee11b600645 100644
--- a/drivers/net/ethernet/broadcom/bgmac-bcma.c
+++ b/drivers/net/ethernet/broadcom/bgmac-bcma.c
@@ -11,6 +11,7 @@
#include <linux/bcma/bcma.h>
#include <linux/brcmphy.h>
#include <linux/etherdevice.h>
+#include <linux/of_net.h>
#include "bgmac.h"
static inline bool bgmac_is_bcm4707_family(struct bcma_device *core)
@@ -96,7 +97,7 @@ static int bgmac_probe(struct bcma_device *core)
struct ssb_sprom *sprom = &core->bus->sprom;
struct mii_bus *mii_bus;
struct bgmac *bgmac;
- u8 *mac;
+ const u8 *mac = NULL;
int err;
bgmac = kzalloc(sizeof(*bgmac), GFP_KERNEL);
@@ -110,21 +111,27 @@ static int bgmac_probe(struct bcma_device *core)
bcma_set_drvdata(core, bgmac);
- switch (core->core_unit) {
- case 0:
- mac = sprom->et0mac;
- break;
- case 1:
- mac = sprom->et1mac;
- break;
- case 2:
- mac = sprom->et2mac;
- break;
- default:
- dev_err(bgmac->dev, "Unsupported core_unit %d\n",
- core->core_unit);
- err = -ENOTSUPP;
- goto err;
+ if (bgmac->dev->of_node)
+ mac = of_get_mac_address(bgmac->dev->of_node);
+
+ /* If no MAC address assigned via device tree, check SPROM */
+ if (!mac) {
+ switch (core->core_unit) {
+ case 0:
+ mac = sprom->et0mac;
+ break;
+ case 1:
+ mac = sprom->et1mac;
+ break;
+ case 2:
+ mac = sprom->et2mac;
+ break;
+ default:
+ dev_err(bgmac->dev, "Unsupported core_unit %d\n",
+ core->core_unit);
+ err = -ENOTSUPP;
+ goto err;
+ }
}
ether_addr_copy(bgmac->mac_addr, mac);
--
2.14.1
From: Rob Herring <[email protected]>
[ Upstream commit bcf54d5385abaea9c8026aae6f4eeb348671a52d ]
If the length of the modalias is greater than the buffer size, then the
modalias is truncated. However the untruncated length is returned which
will cause an error. Fix this to return the truncated length. If an error
in the case was desired, then then we should just return -ENOMEM.
The reality is no device will ever have 4KB of compatible strings to hit
this case.
Signed-off-by: Rob Herring <[email protected]>
Cc: Frank Rowand <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/of/device.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/of/device.c b/drivers/of/device.c
index f7a970120055..3cda60c036f9 100644
--- a/drivers/of/device.c
+++ b/drivers/of/device.c
@@ -223,7 +223,7 @@ ssize_t of_device_get_modalias(struct device *dev, char *str, ssize_t len)
str[i] = '_';
}
- return tsize;
+ return repend;
}
EXPORT_SYMBOL_GPL(of_device_get_modalias);
--
2.14.1
From: Matthias Kaehlcke <[email protected]>
[ Upstream commit fd086045559d90cd7854818b4c60a7119eda6231 ]
Commit 26988efe11b1 ("regulator: core: Allow to get voltage count and
list from parent") introduces the propagation of the parent voltage
count and list for regulators that don't provide this information
themselves. The goal is to support simple switch regulators, however as
a side effect normal continuous regulators can leak details of their
supplies and provide consumers with inconsistent information.
Limit the propagation of the voltage count and list to switch
regulators.
Fixes: 26988efe11b1 ("regulator: core: Allow to get voltage count and
list from parent")
Signed-off-by: Matthias Kaehlcke <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
Tested-by: Javier Martinez Canillas <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/regulator/core.c | 9 +++++++--
include/linux/regulator/driver.h | 2 ++
2 files changed, 9 insertions(+), 2 deletions(-)
diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c
index 9403245503de..178fcda12cec 100644
--- a/drivers/regulator/core.c
+++ b/drivers/regulator/core.c
@@ -2465,7 +2465,7 @@ static int _regulator_list_voltage(struct regulator *regulator,
ret = ops->list_voltage(rdev, selector);
if (lock)
mutex_unlock(&rdev->mutex);
- } else if (rdev->supply) {
+ } else if (rdev->is_switch && rdev->supply) {
ret = _regulator_list_voltage(rdev->supply, selector, lock);
} else {
return -EINVAL;
@@ -2523,7 +2523,7 @@ int regulator_count_voltages(struct regulator *regulator)
if (rdev->desc->n_voltages)
return rdev->desc->n_voltages;
- if (!rdev->supply)
+ if (!rdev->is_switch || !rdev->supply)
return -EINVAL;
return regulator_count_voltages(rdev->supply);
@@ -4049,6 +4049,11 @@ regulator_register(const struct regulator_desc *regulator_desc,
mutex_unlock(®ulator_list_mutex);
}
+ if (!rdev->desc->ops->get_voltage &&
+ !rdev->desc->ops->list_voltage &&
+ !rdev->desc->fixed_uV)
+ rdev->is_switch = true;
+
ret = device_register(&rdev->dev);
if (ret != 0) {
put_device(&rdev->dev);
diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h
index 37b532410528..3c3786df044c 100644
--- a/include/linux/regulator/driver.h
+++ b/include/linux/regulator/driver.h
@@ -425,6 +425,8 @@ struct regulator_dev {
struct regulator_enable_gpio *ena_pin;
unsigned int ena_gpio_state:1;
+ unsigned int is_switch:1;
+
/* time when this regulator was disabled last time */
unsigned long last_off_jiffy;
};
--
2.14.1
From: Nicolai Hähnle <[email protected]>
[ Upstream commit c2c139cf435b18939204800fa72c53a7207bdd68 ]
Fixes a potential race condition in amdgpu that looks as follows:
Task 1: attempt ttm_bo_init, but ttm_bo_validate fails
Task 1: add BO to global list anyway
Task 2: grabs hold of the BO, waits on its reservation lock
Task 1: releases its reference of the BO; never gives up the
reservation lock
The patch "drm/amdgpu: fix a potential deadlock in
amdgpu_bo_create_restricted()" attempts to fix that by releasing
the reservation lock in amdgpu code; unfortunately, it introduces
a use-after-free when this race _doesn't_ happen.
This patch should fix the race properly by never adding the BO
to the global list in the first place.
Cc: zhoucm1 <[email protected]>
Signed-off-by: Nicolai Hähnle <[email protected]>
Tested-by: Samuel Pitoiset <[email protected]>
Reviewed-by: Christian König <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/gpu/drm/ttm/ttm_bo.c | 12 +++++++-----
1 file changed, 7 insertions(+), 5 deletions(-)
diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c
index d09276ec7e90..52a2a1a75682 100644
--- a/drivers/gpu/drm/ttm/ttm_bo.c
+++ b/drivers/gpu/drm/ttm/ttm_bo.c
@@ -1209,18 +1209,20 @@ int ttm_bo_init(struct ttm_bo_device *bdev,
if (likely(!ret))
ret = ttm_bo_validate(bo, placement, interruptible, false);
- if (!resv) {
+ if (!resv)
ttm_bo_unreserve(bo);
- } else if (!(bo->mem.placement & TTM_PL_FLAG_NO_EVICT)) {
+ if (unlikely(ret)) {
+ ttm_bo_unref(&bo);
+ return ret;
+ }
+
+ if (resv && !(bo->mem.placement & TTM_PL_FLAG_NO_EVICT)) {
spin_lock(&bo->glob->lru_lock);
ttm_bo_add_to_lru(bo);
spin_unlock(&bo->glob->lru_lock);
}
- if (unlikely(ret))
- ttm_bo_unref(&bo);
-
return ret;
}
EXPORT_SYMBOL(ttm_bo_init);
--
2.14.1
From: Anton Sviridenko <[email protected]>
[ Upstream commit 6e4c8480bd2eb95309ad3c875e11d2cad98f9188 ]
Fixes warning that appears in dmesg after closing V4L2 userspace
application that plays video from the display device
(first device from V4L2 device nodes provided by solo, usually /dev/video0
when no other V4L2 devices are present). Encoder device nodes are not
affected. Can be reproduced by starting and closing
ffplay -f video4linux2 /dev/video0
[ 8130.281251] ------------[ cut here ]------------
[ 8130.281256] WARNING: CPU: 1 PID: 20414 at drivers/media/v4l2-core/videobuf2-core.c:1651 __vb2_queue_cancel+0x14b/0x230
[ 8130.281257] Modules linked in: ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat solo6x10 x86_pkg_temp_thermal vboxpci(O) vboxnetadp(O) vboxnetflt(O) vboxdrv(O)
[ 8130.281264] CPU: 1 PID: 20414 Comm: ffplay Tainted: G O 4.10.0-gentoo #1
[ 8130.281264] Hardware name: ASUS All Series/B85M-E, BIOS 2301 03/30/2015
[ 8130.281265] Call Trace:
[ 8130.281267] dump_stack+0x4f/0x72
[ 8130.281270] __warn+0xc7/0xf0
[ 8130.281271] warn_slowpath_null+0x18/0x20
[ 8130.281272] __vb2_queue_cancel+0x14b/0x230
[ 8130.281273] vb2_core_streamoff+0x23/0x90
[ 8130.281275] vb2_streamoff+0x24/0x50
[ 8130.281276] vb2_ioctl_streamoff+0x3d/0x50
[ 8130.281278] v4l_streamoff+0x15/0x20
[ 8130.281279] __video_do_ioctl+0x25e/0x2f0
[ 8130.281280] video_usercopy+0x279/0x520
[ 8130.281282] ? v4l_enum_fmt+0x1330/0x1330
[ 8130.281285] ? unmap_region+0xdf/0x110
[ 8130.281285] video_ioctl2+0x10/0x20
[ 8130.281286] v4l2_ioctl+0xce/0xe0
[ 8130.281289] do_vfs_ioctl+0x8b/0x5b0
[ 8130.281290] ? __fget+0x72/0xa0
[ 8130.281291] SyS_ioctl+0x74/0x80
[ 8130.281294] entry_SYSCALL_64_fastpath+0x13/0x94
[ 8130.281295] RIP: 0033:0x7ff86fee6b27
[ 8130.281296] RSP: 002b:00007ffe467f6a08 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[ 8130.281297] RAX: ffffffffffffffda RBX: 00000000d1a4d788 RCX: 00007ff86fee6b27
[ 8130.281297] RDX: 00007ffe467f6a14 RSI: 0000000040045613 RDI: 0000000000000006
[ 8130.281298] RBP: 000000000373f8d0 R08: 00000000ffffffff R09: 00007ff860001140
[ 8130.281298] R10: 0000000000000243 R11: 0000000000000246 R12: 0000000000000000
[ 8130.281299] R13: 00000000000000a0 R14: 00007ffe467f6530 R15: 0000000001f32228
[ 8130.281300] ---[ end trace 00695dc96be646e7 ]---
Signed-off-by: Anton Sviridenko <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/media/pci/solo6x10/solo6x10-v4l2.c | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/drivers/media/pci/solo6x10/solo6x10-v4l2.c b/drivers/media/pci/solo6x10/solo6x10-v4l2.c
index b4be47969b6b..e17d6b945c07 100644
--- a/drivers/media/pci/solo6x10/solo6x10-v4l2.c
+++ b/drivers/media/pci/solo6x10/solo6x10-v4l2.c
@@ -341,6 +341,17 @@ static void solo_stop_streaming(struct vb2_queue *q)
struct solo_dev *solo_dev = vb2_get_drv_priv(q);
solo_stop_thread(solo_dev);
+
+ spin_lock(&solo_dev->slock);
+ while (!list_empty(&solo_dev->vidq_active)) {
+ struct solo_vb2_buf *buf = list_entry(
+ solo_dev->vidq_active.next,
+ struct solo_vb2_buf, list);
+
+ list_del(&buf->list);
+ vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR);
+ }
+ spin_unlock(&solo_dev->slock);
INIT_LIST_HEAD(&solo_dev->vidq_active);
}
--
2.14.1
From: Jaegeuk Kim <[email protected]>
[ Upstream commit c13ff37e359bb3eacf4e1760dcea8d9760aa7459 ]
- has_not_enough_free_secs
node_secs: 0 dent_secs: 0 freed:0 free_segments:103 reserved:104
- f2fs_gc
- get_victim_by_default
alloc_mode 0, gc_mode 1, max_search 2672, offset 4654, ofs_unit 1
- do_garbage_collect
start_segno 3976, end_segno 3977 type 0
- is_alive
nid 22797, blkaddr 2131882, ofs_in_node 0, version 0x8/0x0
- gc_data_segment 766, segno 3976, block 512/426 not alive
So, this patch fixes subtle corrupted case where node version does not match
to summary version which results in infinite loop by gc.
Reported-by: Yunlei He <[email protected]>
Signed-off-by: Jaegeuk Kim <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
fs/f2fs/gc.c | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/fs/f2fs/gc.c b/fs/f2fs/gc.c
index 34a69e7ed90b..17ab23f64bba 100644
--- a/fs/f2fs/gc.c
+++ b/fs/f2fs/gc.c
@@ -538,8 +538,10 @@ static bool is_alive(struct f2fs_sb_info *sbi, struct f2fs_summary *sum,
get_node_info(sbi, nid, dni);
if (sum->version != dni->version) {
- f2fs_put_page(node_page, 1);
- return false;
+ f2fs_msg(sbi->sb, KERN_WARNING,
+ "%s: valid data with mismatched node version.",
+ __func__);
+ set_sbi_flag(sbi, SBI_NEED_FSCK);
}
*nofs = ofs_of_node(node_page);
--
2.14.1
From: Arnaldo Carvalho de Melo <[email protected]>
[ Upstream commit fd2b2975149f5f7099693027cece81b16842964a ]
Which may happen when we start a tracing session and a thread is waiting
for something like "poll" to return, in which case we better print "?"
both for the syscall entry timestamp and for the duration.
E.g.:
Tracing existing mutt session:
# perf trace -p `pidof mutt`
? ( ? ): mutt/17135 ... [continued]: poll()) = 1
0.027 ( 0.013 ms): mutt/17135 read(buf: 0x7ffcb3c42cef, count: 1) = 1
0.047 ( 0.008 ms): mutt/17135 poll(ufds: 0x7ffcb3c42c50, nfds: 1, timeout_msecs: 1000) = 1
0.059 ( 0.008 ms): mutt/17135 read(buf: 0x7ffcb3c42cef, count: 1) = 1
<SNIP>
Before it would print a large number because we'd do:
ttrace->entry_time - trace->base_time
And entry_time would be 0, while base_time would be the timestamp for
the first event 'perf trace' reads, oops.
Cc: Adrian Hunter <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Luis Claudio Gonçalves <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/perf/builtin-trace.c | 43 ++++++++++++++++++++++++++++++++++---------
1 file changed, 34 insertions(+), 9 deletions(-)
diff --git a/tools/perf/builtin-trace.c b/tools/perf/builtin-trace.c
index 21f8a81797a0..4c596ba310cb 100644
--- a/tools/perf/builtin-trace.c
+++ b/tools/perf/builtin-trace.c
@@ -822,12 +822,21 @@ struct syscall {
void **arg_parm;
};
-static size_t fprintf_duration(unsigned long t, FILE *fp)
+/*
+ * We need to have this 'calculated' boolean because in some cases we really
+ * don't know what is the duration of a syscall, for instance, when we start
+ * a session and some threads are waiting for a syscall to finish, say 'poll',
+ * in which case all we can do is to print "( ? ) for duration and for the
+ * start timestamp.
+ */
+static size_t fprintf_duration(unsigned long t, bool calculated, FILE *fp)
{
double duration = (double)t / NSEC_PER_MSEC;
size_t printed = fprintf(fp, "(");
- if (duration >= 1.0)
+ if (!calculated)
+ printed += fprintf(fp, " ? ");
+ else if (duration >= 1.0)
printed += color_fprintf(fp, PERF_COLOR_RED, "%6.3f ms", duration);
else if (duration >= 0.01)
printed += color_fprintf(fp, PERF_COLOR_YELLOW, "%6.3f ms", duration);
@@ -1030,13 +1039,27 @@ static bool trace__filter_duration(struct trace *trace, double t)
return t < (trace->duration_filter * NSEC_PER_MSEC);
}
-static size_t trace__fprintf_tstamp(struct trace *trace, u64 tstamp, FILE *fp)
+static size_t __trace__fprintf_tstamp(struct trace *trace, u64 tstamp, FILE *fp)
{
double ts = (double)(tstamp - trace->base_time) / NSEC_PER_MSEC;
return fprintf(fp, "%10.3f ", ts);
}
+/*
+ * We're handling tstamp=0 as an undefined tstamp, i.e. like when we are
+ * using ttrace->entry_time for a thread that receives a sys_exit without
+ * first having received a sys_enter ("poll" issued before tracing session
+ * starts, lost sys_enter exit due to ring buffer overflow).
+ */
+static size_t trace__fprintf_tstamp(struct trace *trace, u64 tstamp, FILE *fp)
+{
+ if (tstamp > 0)
+ return __trace__fprintf_tstamp(trace, tstamp, fp);
+
+ return fprintf(fp, " ? ");
+}
+
static bool done = false;
static bool interrupted = false;
@@ -1047,10 +1070,10 @@ static void sig_handler(int sig)
}
static size_t trace__fprintf_entry_head(struct trace *trace, struct thread *thread,
- u64 duration, u64 tstamp, FILE *fp)
+ u64 duration, bool duration_calculated, u64 tstamp, FILE *fp)
{
size_t printed = trace__fprintf_tstamp(trace, tstamp, fp);
- printed += fprintf_duration(duration, fp);
+ printed += fprintf_duration(duration, duration_calculated, fp);
if (trace->multiple_threads) {
if (trace->show_comm)
@@ -1452,7 +1475,7 @@ static int trace__printf_interrupted_entry(struct trace *trace, struct perf_samp
duration = sample->time - ttrace->entry_time;
- printed = trace__fprintf_entry_head(trace, trace->current, duration, ttrace->entry_time, trace->output);
+ printed = trace__fprintf_entry_head(trace, trace->current, duration, true, ttrace->entry_time, trace->output);
printed += fprintf(trace->output, "%-70s) ...\n", ttrace->entry_str);
ttrace->entry_pending = false;
@@ -1499,7 +1522,7 @@ static int trace__sys_enter(struct trace *trace, struct perf_evsel *evsel,
if (sc->is_exit) {
if (!(trace->duration_filter || trace->summary_only || trace->min_stack)) {
- trace__fprintf_entry_head(trace, thread, 1, ttrace->entry_time, trace->output);
+ trace__fprintf_entry_head(trace, thread, 0, false, ttrace->entry_time, trace->output);
fprintf(trace->output, "%-70s)\n", ttrace->entry_str);
}
} else {
@@ -1547,6 +1570,7 @@ static int trace__sys_exit(struct trace *trace, struct perf_evsel *evsel,
{
long ret;
u64 duration = 0;
+ bool duration_calculated = false;
struct thread *thread;
int id = perf_evsel__sc_tp_uint(evsel, id, sample), err = -1, callchain_ret = 0;
struct syscall *sc = trace__syscall_info(trace, evsel, id);
@@ -1577,6 +1601,7 @@ static int trace__sys_exit(struct trace *trace, struct perf_evsel *evsel,
duration = sample->time - ttrace->entry_time;
if (trace__filter_duration(trace, duration))
goto out;
+ duration_calculated = true;
} else if (trace->duration_filter)
goto out;
@@ -1592,7 +1617,7 @@ static int trace__sys_exit(struct trace *trace, struct perf_evsel *evsel,
if (trace->summary_only)
goto out;
- trace__fprintf_entry_head(trace, thread, duration, ttrace->entry_time, trace->output);
+ trace__fprintf_entry_head(trace, thread, duration, duration_calculated, ttrace->entry_time, trace->output);
if (ttrace->entry_pending) {
fprintf(trace->output, "%-70s", ttrace->entry_str);
@@ -1855,7 +1880,7 @@ static int trace__pgfault(struct trace *trace,
thread__find_addr_location(thread, sample->cpumode, MAP__FUNCTION,
sample->ip, &al);
- trace__fprintf_entry_head(trace, thread, 0, sample->time, trace->output);
+ trace__fprintf_entry_head(trace, thread, 0, true, sample->time, trace->output);
fprintf(trace->output, "%sfault [",
evsel->attr.config == PERF_COUNT_SW_PAGE_FAULTS_MAJ ?
--
2.14.1
From: Takashi Sakamoto <[email protected]>
[ Upstream commit 8820a4cf0cb4cd5c6540a9a18b2cedbdfd5a6891 ]
At a commit 9dc5d31cdceb ("ALSA: firewire-digi00x: handle MIDI messages in
isochronous packets"), a functionality to handle MIDI messages on
isochronous packet was supported. But this includes some of my
misunderstanding. This commit is to fix them.
For digi00x series, first data channel of data blocks in rx/tx packet
includes MIDI messages. The data channel has 0x80 in 8 bit of its MSB,
however it's against IEC 61883-6. Unique data format is applied:
- Upper 4 bits of LSB represent port number.
- 0x0: port 1.
- 0x2: port 2.
- 0xe: console port.
- Lower 4 bits of LSB represent the number of included MIDI message bytes;
0x0/0x1/0x2.
- Two bytes of middle of this data channel have MIDI bytes.
Especially, MIDI messages from/to console surface are also transferred by
isochronous packets, as well as physical MIDI ports.
Signed-off-by: Takashi Sakamoto <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
sound/firewire/digi00x/amdtp-dot.c | 55 +++++++++++++++++++++++++-------------
1 file changed, 37 insertions(+), 18 deletions(-)
diff --git a/sound/firewire/digi00x/amdtp-dot.c b/sound/firewire/digi00x/amdtp-dot.c
index b3cffd01a19f..a4688545339c 100644
--- a/sound/firewire/digi00x/amdtp-dot.c
+++ b/sound/firewire/digi00x/amdtp-dot.c
@@ -28,6 +28,9 @@
*/
#define MAX_MIDI_RX_BLOCKS 8
+/* 3 = MAX(DOT_MIDI_IN_PORTS, DOT_MIDI_OUT_PORTS) + 1. */
+#define MAX_MIDI_PORTS 3
+
/*
* The double-oh-three algorithm was discovered by Robin Gareus and Damien
* Zammit in 2012, with reverse-engineering for Digi 003 Rack.
@@ -42,10 +45,8 @@ struct amdtp_dot {
unsigned int pcm_channels;
struct dot_state state;
- unsigned int midi_ports;
- /* 2 = MAX(DOT_MIDI_IN_PORTS, DOT_MIDI_OUT_PORTS) */
- struct snd_rawmidi_substream *midi[2];
- int midi_fifo_used[2];
+ struct snd_rawmidi_substream *midi[MAX_MIDI_PORTS];
+ int midi_fifo_used[MAX_MIDI_PORTS];
int midi_fifo_limit;
void (*transfer_samples)(struct amdtp_stream *s,
@@ -124,8 +125,8 @@ int amdtp_dot_set_parameters(struct amdtp_stream *s, unsigned int rate,
return -EBUSY;
/*
- * A first data channel is for MIDI conformant data channel, the rest is
- * Multi Bit Linear Audio data channel.
+ * A first data channel is for MIDI messages, the rest is Multi Bit
+ * Linear Audio data channel.
*/
err = amdtp_stream_set_parameters(s, rate, pcm_channels + 1);
if (err < 0)
@@ -135,11 +136,6 @@ int amdtp_dot_set_parameters(struct amdtp_stream *s, unsigned int rate,
p->pcm_channels = pcm_channels;
- if (s->direction == AMDTP_IN_STREAM)
- p->midi_ports = DOT_MIDI_IN_PORTS;
- else
- p->midi_ports = DOT_MIDI_OUT_PORTS;
-
/*
* We do not know the actual MIDI FIFO size of most devices. Just
* assume two bytes, i.e., one byte can be received over the bus while
@@ -281,13 +277,25 @@ static void write_midi_messages(struct amdtp_stream *s, __be32 *buffer,
b = (u8 *)&buffer[0];
len = 0;
- if (port < p->midi_ports &&
+ if (port < MAX_MIDI_PORTS &&
midi_ratelimit_per_packet(s, port) &&
p->midi[port] != NULL)
len = snd_rawmidi_transmit(p->midi[port], b + 1, 2);
if (len > 0) {
- b[3] = (0x10 << port) | len;
+ /*
+ * Upper 4 bits of LSB represent port number.
+ * - 0000b: physical MIDI port 1.
+ * - 0010b: physical MIDI port 2.
+ * - 1110b: console MIDI port.
+ */
+ if (port == 2)
+ b[3] = 0xe0;
+ else if (port == 1)
+ b[3] = 0x20;
+ else
+ b[3] = 0x00;
+ b[3] |= len;
midi_use_bytes(s, port, len);
} else {
b[1] = 0;
@@ -309,11 +317,22 @@ static void read_midi_messages(struct amdtp_stream *s, __be32 *buffer,
for (f = 0; f < data_blocks; f++) {
b = (u8 *)&buffer[0];
- port = b[3] >> 4;
- len = b[3] & 0x0f;
- if (port < p->midi_ports && p->midi[port] && len > 0)
- snd_rawmidi_receive(p->midi[port], b + 1, len);
+ len = b[3] & 0x0f;
+ if (len > 0) {
+ /*
+ * Upper 4 bits of LSB represent port number.
+ * - 0000b: physical MIDI port 1. Use port 0.
+ * - 1110b: console MIDI port. Use port 2.
+ */
+ if (b[3] >> 4 > 0)
+ port = 2;
+ else
+ port = 0;
+
+ if (port < MAX_MIDI_PORTS && p->midi[port])
+ snd_rawmidi_receive(p->midi[port], b + 1, len);
+ }
buffer += s->data_block_quadlets;
}
@@ -364,7 +383,7 @@ void amdtp_dot_midi_trigger(struct amdtp_stream *s, unsigned int port,
{
struct amdtp_dot *p = s->protocol;
- if (port < p->midi_ports)
+ if (port < MAX_MIDI_PORTS)
ACCESS_ONCE(p->midi[port]) = midi;
}
--
2.14.1
From: Geert Uytterhoeven <[email protected]>
[ Upstream commit 16fe68dcab5702a024d85229ff7e98979cb701a5 ]
The SSI-ALL gate clock is located in between the P clock and the
individual SSI[0-9] clocks, hence the former should be listed as their
parent.
Fixes: ee9141522dcf13f8 ("ARM: shmobile: r8a7791: add MSTP10 support on DTSI")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/r8a7791.dtsi | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 64749080e639..59405ebdce01 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -1437,8 +1437,11 @@
compatible = "renesas,r8a7791-mstp-clocks", "renesas,cpg-mstp-clocks";
reg = <0 0xe6150998 0 4>, <0 0xe61509a8 0 4>;
clocks = <&p_clk>,
- <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>,
- <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>,
+ <&mstp10_clks R8A7791_CLK_SSI_ALL>, <&mstp10_clks R8A7791_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7791_CLK_SSI_ALL>, <&mstp10_clks R8A7791_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7791_CLK_SSI_ALL>, <&mstp10_clks R8A7791_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7791_CLK_SSI_ALL>, <&mstp10_clks R8A7791_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7791_CLK_SSI_ALL>, <&mstp10_clks R8A7791_CLK_SSI_ALL>,
<&p_clk>,
<&mstp10_clks R8A7791_CLK_SCU_ALL>, <&mstp10_clks R8A7791_CLK_SCU_ALL>,
<&mstp10_clks R8A7791_CLK_SCU_ALL>, <&mstp10_clks R8A7791_CLK_SCU_ALL>,
--
2.14.1
From: "Mintz, Yuval" <[email protected]>
[ Upstream commit 2f78227874754b1e10cd348fd6e7693b0dabb3f6 ]
When qedr is enabled, qed would try dividing the msi-x vectors between
L2 and RoCE, starting with L2 and providing it with sufficient vectors
for its queues.
Problem is qed would also do that for storage partitions, and as those
don't need queues it would lead qed to award those partitions with 0
msi-x vectors, causing them to believe theye're using INTa and
preventing them from operating.
Fixes: 51ff17251c9c ("qed: Add support for RoCE hw init")
Signed-off-by: Yuval Mintz <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/qlogic/qed/qed_main.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/qlogic/qed/qed_main.c b/drivers/net/ethernet/qlogic/qed/qed_main.c
index 333c7442e48a..dba3fbe4800e 100644
--- a/drivers/net/ethernet/qlogic/qed/qed_main.c
+++ b/drivers/net/ethernet/qlogic/qed/qed_main.c
@@ -711,7 +711,8 @@ static int qed_slowpath_setup_int(struct qed_dev *cdev,
cdev->int_params.fp_msix_cnt = cdev->int_params.out.num_vectors -
cdev->num_hwfns;
- if (!IS_ENABLED(CONFIG_QED_RDMA))
+ if (!IS_ENABLED(CONFIG_QED_RDMA) ||
+ QED_LEADING_HWFN(cdev)->hw_info.personality != QED_PCI_ETH_ROCE)
return 0;
for_each_hwfn(cdev, i)
--
2.14.1
From: David Daney <[email protected]>
[ Upstream commit a81507c79f4ae9a0f9fb1054b59b62a090620dd9 ]
o Socket data is unsigned, so use unsigned accessors instructions.
o Fix path result pointer generation arithmetic.
o Fix half-word byte swapping code for unsigned semantics.
Signed-off-by: David Daney <[email protected]>
Cc: James Hogan <[email protected]>
Cc: Alexei Starovoitov <[email protected]>
Cc: Steven J. Hill <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Patchwork: https://patchwork.linux-mips.org/patch/15747/
Signed-off-by: Ralf Baechle <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/mips/net/bpf_jit_asm.S | 23 ++++++++++++-----------
1 file changed, 12 insertions(+), 11 deletions(-)
diff --git a/arch/mips/net/bpf_jit_asm.S b/arch/mips/net/bpf_jit_asm.S
index 5d2e0c8d29c0..88a2075305d1 100644
--- a/arch/mips/net/bpf_jit_asm.S
+++ b/arch/mips/net/bpf_jit_asm.S
@@ -90,18 +90,14 @@ FEXPORT(sk_load_half_positive)
is_offset_in_header(2, half)
/* Offset within header boundaries */
PTR_ADDU t1, $r_skb_data, offset
- .set reorder
- lh $r_A, 0(t1)
- .set noreorder
+ lhu $r_A, 0(t1)
#ifdef CONFIG_CPU_LITTLE_ENDIAN
# if defined(__mips_isa_rev) && (__mips_isa_rev >= 2)
- wsbh t0, $r_A
- seh $r_A, t0
+ wsbh $r_A, $r_A
# else
- sll t0, $r_A, 24
- andi t1, $r_A, 0xff00
- sra t0, t0, 16
- srl t1, t1, 8
+ sll t0, $r_A, 8
+ srl t1, $r_A, 8
+ andi t0, t0, 0xff00
or $r_A, t0, t1
# endif
#endif
@@ -115,7 +111,7 @@ FEXPORT(sk_load_byte_positive)
is_offset_in_header(1, byte)
/* Offset within header boundaries */
PTR_ADDU t1, $r_skb_data, offset
- lb $r_A, 0(t1)
+ lbu $r_A, 0(t1)
jr $r_ra
move $r_ret, zero
END(sk_load_byte)
@@ -139,6 +135,11 @@ FEXPORT(sk_load_byte_positive)
* (void *to) is returned in r_s0
*
*/
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+#define DS_OFFSET(SIZE) (4 * SZREG)
+#else
+#define DS_OFFSET(SIZE) ((4 * SZREG) + (4 - SIZE))
+#endif
#define bpf_slow_path_common(SIZE) \
/* Quick check. Are we within reasonable boundaries? */ \
LONG_ADDIU $r_s1, $r_skb_len, -SIZE; \
@@ -150,7 +151,7 @@ FEXPORT(sk_load_byte_positive)
PTR_LA t0, skb_copy_bits; \
PTR_S $r_ra, (5 * SZREG)($r_sp); \
/* Assign low slot to a2 */ \
- move a2, $r_sp; \
+ PTR_ADDIU a2, $r_sp, DS_OFFSET(SIZE); \
jalr t0; \
/* Reset our destination slot (DS but it's ok) */ \
INT_S zero, (4 * SZREG)($r_sp); \
--
2.14.1
From: Takashi Sakamoto <[email protected]>
[ Upstream commit 13e005f9f933a35b5e55c9d36f151efe2a8383ec ]
Digi00x series includes two types of unit; rack and console. As long as
reading information on config rom of Digi 002 console, 'MODEL_ID' field
has a different value from the one on Digi 002 rack.
We've already got a test report from users with Digi 003 rack. We can
assume that console type and rack type has different value in the field.
This commit adds a device entry for console type. For following commits,
this commit also adds a member to 'struct snd_digi00x' to identify console
type.
$ cd linux-firewire-utils/src
$ python2 ./crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 0404f9d0 bus_info_length 4, crc_length 4, crc 63952
404 31333934 bus_name "1394"
408 60647002 irmc 0, cmc 1, isc 1, bmc 0, cyc_clk_acc 100, max_rec 7 (256)
40c 00a07e00 company_id 00a07e |
410 00a30000 device_id 0000a30000 | EUI-64 00a07e0000a30000
root directory
-----------------------------------------------------------------
414 00058a39 directory_length 5, crc 35385
418 0c0043a0 node capabilities
41c 04000001 hardware version
420 0300a07e vendor
424 81000007 --> descriptor leaf at 440
428 d1000001 --> unit directory at 42c
unit directory at 42c
-----------------------------------------------------------------
42c 00046674 directory_length 4, crc 26228
430 120000a3 specifier id
434 13000001 version
438 17000001 model
43c 81000007 --> descriptor leaf at 458
descriptor leaf at 440
-----------------------------------------------------------------
440 00055913 leaf_length 5, crc 22803
444 000050f2 descriptor_type 00, specifier_ID 50f2
448 80000000
44c 44696769
450 64657369
454 676e0000
descriptor leaf at 458
-----------------------------------------------------------------
458 0004a6fd leaf_length 4, crc 42749
45c 00000000 textual descriptor
460 00000000 minimal ASCII
464 44696769 "Digi"
468 20303032 " 002"
Signed-off-by: Takashi Sakamoto <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
sound/firewire/digi00x/digi00x.c | 13 +++++++++++--
sound/firewire/digi00x/digi00x.h | 1 +
2 files changed, 12 insertions(+), 2 deletions(-)
diff --git a/sound/firewire/digi00x/digi00x.c b/sound/firewire/digi00x/digi00x.c
index cc4776c6ded3..1f5e1d23f31a 100644
--- a/sound/firewire/digi00x/digi00x.c
+++ b/sound/firewire/digi00x/digi00x.c
@@ -13,7 +13,8 @@ MODULE_AUTHOR("Takashi Sakamoto <[email protected]>");
MODULE_LICENSE("GPL v2");
#define VENDOR_DIGIDESIGN 0x00a07e
-#define MODEL_DIGI00X 0x000002
+#define MODEL_CONSOLE 0x000001
+#define MODEL_RACK 0x000002
static int name_card(struct snd_dg00x *dg00x)
{
@@ -129,6 +130,8 @@ static int snd_dg00x_probe(struct fw_unit *unit,
spin_lock_init(&dg00x->lock);
init_waitqueue_head(&dg00x->hwdep_wait);
+ dg00x->is_console = entry->model_id == MODEL_CONSOLE;
+
/* Allocate and register this sound card later. */
INIT_DEFERRABLE_WORK(&dg00x->dwork, do_registration);
snd_fw_schedule_registration(unit, &dg00x->dwork);
@@ -183,7 +186,13 @@ static const struct ieee1394_device_id snd_dg00x_id_table[] = {
.match_flags = IEEE1394_MATCH_VENDOR_ID |
IEEE1394_MATCH_MODEL_ID,
.vendor_id = VENDOR_DIGIDESIGN,
- .model_id = MODEL_DIGI00X,
+ .model_id = MODEL_CONSOLE,
+ },
+ {
+ .match_flags = IEEE1394_MATCH_VENDOR_ID |
+ IEEE1394_MATCH_MODEL_ID,
+ .vendor_id = VENDOR_DIGIDESIGN,
+ .model_id = MODEL_RACK,
},
{}
};
diff --git a/sound/firewire/digi00x/digi00x.h b/sound/firewire/digi00x/digi00x.h
index 2cd465c0caae..43bcb0ce69c0 100644
--- a/sound/firewire/digi00x/digi00x.h
+++ b/sound/firewire/digi00x/digi00x.h
@@ -60,6 +60,7 @@ struct snd_dg00x {
/* For asynchronous MIDI controls. */
struct snd_rawmidi_substream *in_control;
struct snd_fw_async_midi_port out_control;
+ bool is_console;
};
#define DG00X_ADDR_BASE 0xffffe0000000ull
--
2.14.1
From: Vincent Stehlé <[email protected]>
[ Upstream commit 0c08aaf873174c95e674cf21ffcd041c589d2e5b ]
ISL9305_MAX_REGULATOR is the last index used to access the init_data[]
array, so we need to add one to this last index to obtain the necessary
array size.
This fixes the following smatch error:
drivers/regulator/isl9305.c:160 isl9305_i2c_probe() error: buffer overflow 'pdata->init_data' 3 <= 3
Fixes: dec38b5ce6a9edb4 ("regulator: isl9305: Add Intersil ISL9305/H driver")
Signed-off-by: Vincent Stehlé <[email protected]>
Cc: Mark Brown <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
include/linux/platform_data/isl9305.h | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/include/linux/platform_data/isl9305.h b/include/linux/platform_data/isl9305.h
index 1419133fa69e..4ac1a070af0a 100644
--- a/include/linux/platform_data/isl9305.h
+++ b/include/linux/platform_data/isl9305.h
@@ -24,7 +24,7 @@
struct regulator_init_data;
struct isl9305_pdata {
- struct regulator_init_data *init_data[ISL9305_MAX_REGULATOR];
+ struct regulator_init_data *init_data[ISL9305_MAX_REGULATOR + 1];
};
#endif
--
2.14.1
From: "Luis R. Rodriguez" <[email protected]>
[ Upstream commit 65c79230576873b312c3599479c1e42355c9f349 ]
The file /sys/module/firmware_class/parameters/path can be used
to set a custom firmware path. The fw_filesystem.sh script creates
a temporary directory to add a test firmware file to be used during
testing, in order for this to work it uses the custom path syfs file
and it was supposed to reset back the file on execution exit. The
script failed to do this due to a typo, it was using OLD_PATH instead
of OLD_FWPATH, since its inception since v3.17.
Its not as easy to just keep the old setting, it turns out that
resetting an empty setting won't actually do what we want, we need
to check if it was empty and set an empty space.
Without this we end up having the temporary path always set after
we run these tests.
Fixes: 0a8adf58475 ("test: add firmware_class loader test")
Signed-off-by: Luis R. Rodriguez <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/testing/selftests/firmware/fw_filesystem.sh | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/tools/testing/selftests/firmware/fw_filesystem.sh b/tools/testing/selftests/firmware/fw_filesystem.sh
index d8ac9ba67688..17e16fcaa0cc 100755
--- a/tools/testing/selftests/firmware/fw_filesystem.sh
+++ b/tools/testing/selftests/firmware/fw_filesystem.sh
@@ -28,7 +28,10 @@ test_finish()
if [ "$HAS_FW_LOADER_USER_HELPER" = "yes" ]; then
echo "$OLD_TIMEOUT" >/sys/class/firmware/timeout
fi
- echo -n "$OLD_PATH" >/sys/module/firmware_class/parameters/path
+ if [ "$OLD_FWPATH" = "" ]; then
+ OLD_FWPATH=" "
+ fi
+ echo -n "$OLD_FWPATH" >/sys/module/firmware_class/parameters/path
rm -f "$FW"
rmdir "$FWPATH"
}
--
2.14.1
From: "Andrew F. Davis" <[email protected]>
[ Upstream commit dcb407b257af06fa58b0544ec01ec9e0d3927e02 ]
Currently BCLK inverting is only handled when the DAI format is
DSP, but the BCLK may be inverted in any supported mode. Without
this using this CODEC in any other mode than DSP with the BCLK
inverted leads to bad sampling timing and very poor audio quality.
Signed-off-by: Andrew F. Davis <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
sound/soc/codecs/tlv320aic31xx.c | 28 ++++++++++++++++++----------
1 file changed, 18 insertions(+), 10 deletions(-)
diff --git a/sound/soc/codecs/tlv320aic31xx.c b/sound/soc/codecs/tlv320aic31xx.c
index be1a64bfd320..16b0e600ed4c 100644
--- a/sound/soc/codecs/tlv320aic31xx.c
+++ b/sound/soc/codecs/tlv320aic31xx.c
@@ -924,6 +924,18 @@ static int aic31xx_set_dai_fmt(struct snd_soc_dai *codec_dai,
return -EINVAL;
}
+ /* signal polarity */
+ switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+ case SND_SOC_DAIFMT_NB_NF:
+ break;
+ case SND_SOC_DAIFMT_IB_NF:
+ iface_reg2 |= AIC31XX_BCLKINV_MASK;
+ break;
+ default:
+ dev_err(codec->dev, "Invalid DAI clock signal polarity\n");
+ return -EINVAL;
+ }
+
/* interface format */
switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
case SND_SOC_DAIFMT_I2S:
@@ -931,16 +943,12 @@ static int aic31xx_set_dai_fmt(struct snd_soc_dai *codec_dai,
case SND_SOC_DAIFMT_DSP_A:
dsp_a_val = 0x1;
case SND_SOC_DAIFMT_DSP_B:
- /* NOTE: BCLKINV bit value 1 equas NB and 0 equals IB */
- switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
- case SND_SOC_DAIFMT_NB_NF:
- iface_reg2 |= AIC31XX_BCLKINV_MASK;
- break;
- case SND_SOC_DAIFMT_IB_NF:
- break;
- default:
- return -EINVAL;
- }
+ /*
+ * NOTE: This CODEC samples on the falling edge of BCLK in
+ * DSP mode, this is inverted compared to what most DAIs
+ * expect, so we invert for this mode
+ */
+ iface_reg2 ^= AIC31XX_BCLKINV_MASK;
iface_reg1 |= (AIC31XX_DSP_MODE <<
AIC31XX_IFACE1_DATATYPE_SHIFT);
break;
--
2.14.1
From: "Paul E. McKenney" <[email protected]>
[ Upstream commit a0982dfa03efca6c239c52cabebcea4afb93ea6b ]
The rcutorture test suite occasionally provokes a splat due to invoking
resched_cpu() on an offline CPU:
WARNING: CPU: 2 PID: 8 at /home/paulmck/public_git/linux-rcu/arch/x86/kernel/smp.c:128 native_smp_send_reschedule+0x37/0x40
Modules linked in:
CPU: 2 PID: 8 Comm: rcu_preempt Not tainted 4.14.0-rc4+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
task: ffff902ede9daf00 task.stack: ffff96c50010c000
RIP: 0010:native_smp_send_reschedule+0x37/0x40
RSP: 0018:ffff96c50010fdb8 EFLAGS: 00010096
RAX: 000000000000002e RBX: ffff902edaab4680 RCX: 0000000000000003
RDX: 0000000080000003 RSI: 0000000000000000 RDI: 00000000ffffffff
RBP: ffff96c50010fdb8 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: 00000000299f36ae R12: 0000000000000001
R13: ffffffff9de64240 R14: 0000000000000001 R15: ffffffff9de64240
FS: 0000000000000000(0000) GS:ffff902edfc80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000f7d4c642 CR3: 000000001e0e2000 CR4: 00000000000006e0
Call Trace:
resched_curr+0x8f/0x1c0
resched_cpu+0x2c/0x40
rcu_implicit_dynticks_qs+0x152/0x220
force_qs_rnp+0x147/0x1d0
? sync_rcu_exp_select_cpus+0x450/0x450
rcu_gp_kthread+0x5a9/0x950
kthread+0x142/0x180
? force_qs_rnp+0x1d0/0x1d0
? kthread_create_on_node+0x40/0x40
ret_from_fork+0x27/0x40
Code: 14 01 0f 92 c0 84 c0 74 14 48 8b 05 14 4f f4 00 be fd 00 00 00 ff 90 a0 00 00 00 5d c3 89 fe 48 c7 c7 38 89 ca 9d e8 e5 56 08 00 <0f> ff 5d c3 0f 1f 44 00 00 8b 05 52 9e 37 02 85 c0 75 38 55 48
---[ end trace 26df9e5df4bba4ac ]---
This splat cannot be generated by expedited grace periods because they
always invoke resched_cpu() on the current CPU, which is good because
expedited grace periods require that resched_cpu() unconditionally
succeed. However, other parts of RCU can tolerate resched_cpu() acting
as a no-op, at least as long as it doesn't happen too often.
This commit therefore makes resched_cpu() invoke resched_curr() only if
the CPU is either online or is the current CPU.
Signed-off-by: Paul E. McKenney <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
kernel/sched/core.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/kernel/sched/core.c b/kernel/sched/core.c
index bce3a7ad4253..291ea6fa7ee6 100644
--- a/kernel/sched/core.c
+++ b/kernel/sched/core.c
@@ -508,7 +508,8 @@ void resched_cpu(int cpu)
unsigned long flags;
raw_spin_lock_irqsave(&rq->lock, flags);
- resched_curr(rq);
+ if (cpu_online(cpu) || cpu == smp_processor_id())
+ resched_curr(rq);
raw_spin_unlock_irqrestore(&rq->lock, flags);
}
--
2.14.1
From: Srinivas Kandagatla <[email protected]>
[ Upstream commit d8e488e8242ecf129eebc440c92d800a99ca109d ]
This patch fixes missing mnd_width for codec_digital clk, this is now set to
8 inline with datasheet.
Fixes: 3966fab8b6ab ("clk: qcom: Add MSM8916 Global Clock Controller support")
Signed-off-by: Srinivas Kandagatla <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/clk/qcom/gcc-msm8916.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/clk/qcom/gcc-msm8916.c b/drivers/clk/qcom/gcc-msm8916.c
index 5c4e193164d4..8dd71345b5d0 100644
--- a/drivers/clk/qcom/gcc-msm8916.c
+++ b/drivers/clk/qcom/gcc-msm8916.c
@@ -1437,6 +1437,7 @@ static const struct freq_tbl ftbl_codec_clk[] = {
static struct clk_rcg2 codec_digcodec_clk_src = {
.cmd_rcgr = 0x1c09c,
+ .mnd_width = 8,
.hid_width = 5,
.parent_map = gcc_xo_gpll1_emclk_sleep_map,
.freq_tbl = ftbl_codec_clk,
--
2.14.1
From: Tobias Jordan <[email protected]>
[ Upstream commit 2d9bbd02c54094ceffa555143b0d68cd06504d63 ]
sun6i_spi_probe() uses sun6i_spi_runtime_resume() to prepare/enable
clocks, so sun6i_spi_remove() should use sun6i_spi_runtime_suspend() to
disable/unprepare them if we're not suspended.
Replacing pm_runtime_disable() by pm_runtime_force_suspend() will ensure
that sun6i_spi_runtime_suspend() is called if needed.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3558fe900e8af (spi: sunxi: Add Allwinner A31 SPI controller driver)
Signed-off-by: Tobias Jordan <[email protected]>
Acked-by: Maxime Ripard <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/spi/spi-sun6i.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/spi/spi-sun6i.c b/drivers/spi/spi-sun6i.c
index 9918a57a6a6e..7e7da97982aa 100644
--- a/drivers/spi/spi-sun6i.c
+++ b/drivers/spi/spi-sun6i.c
@@ -464,7 +464,7 @@ err_free_master:
static int sun6i_spi_remove(struct platform_device *pdev)
{
- pm_runtime_disable(&pdev->dev);
+ pm_runtime_force_suspend(&pdev->dev);
return 0;
}
--
2.14.1
From: Yong Zhao <[email protected]>
[ Upstream commit 5108d768408abc80e4e8d99f5b406a73cb04056b ]
Kobject created using kobject_create_and_add() can be freed using
kobject_put() when there is no referenece any more. However,
kobject memory allocated with kzalloc() has to set up a release
callback in order to free it when the counter decreases to 0.
Otherwise it causes memory leak.
Signed-off-by: Yong Zhao <[email protected]>
Signed-off-by: Felix Kuehling <[email protected]>
Reviewed-by: Oded Gabbay <[email protected]>
Signed-off-by: Oded Gabbay <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/gpu/drm/amd/amdkfd/kfd_topology.c | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/drivers/gpu/drm/amd/amdkfd/kfd_topology.c b/drivers/gpu/drm/amd/amdkfd/kfd_topology.c
index 1e5064749959..8c6e47c5507f 100644
--- a/drivers/gpu/drm/amd/amdkfd/kfd_topology.c
+++ b/drivers/gpu/drm/amd/amdkfd/kfd_topology.c
@@ -519,11 +519,17 @@ static ssize_t sysprops_show(struct kobject *kobj, struct attribute *attr,
return ret;
}
+static void kfd_topology_kobj_release(struct kobject *kobj)
+{
+ kfree(kobj);
+}
+
static const struct sysfs_ops sysprops_ops = {
.show = sysprops_show,
};
static struct kobj_type sysprops_type = {
+ .release = kfd_topology_kobj_release,
.sysfs_ops = &sysprops_ops,
};
@@ -559,6 +565,7 @@ static const struct sysfs_ops iolink_ops = {
};
static struct kobj_type iolink_type = {
+ .release = kfd_topology_kobj_release,
.sysfs_ops = &iolink_ops,
};
@@ -586,6 +593,7 @@ static const struct sysfs_ops mem_ops = {
};
static struct kobj_type mem_type = {
+ .release = kfd_topology_kobj_release,
.sysfs_ops = &mem_ops,
};
@@ -625,6 +633,7 @@ static const struct sysfs_ops cache_ops = {
};
static struct kobj_type cache_type = {
+ .release = kfd_topology_kobj_release,
.sysfs_ops = &cache_ops,
};
@@ -747,6 +756,7 @@ static const struct sysfs_ops node_ops = {
};
static struct kobj_type node_type = {
+ .release = kfd_topology_kobj_release,
.sysfs_ops = &node_ops,
};
--
2.14.1
From: Davidlohr Bueso <[email protected]>
[ Upstream commit 2ce77d16db4240dd2e422fc0a5c26d3e2ec03446 ]
Things can explode for locktorture if the user does combinations
of nwriters_stress=0 nreaders_stress=0. Fix this by not assuming
we always want to torture writer threads.
Reported-by: Jeremy Linton <[email protected]>
Signed-off-by: Davidlohr Bueso <[email protected]>
Signed-off-by: Paul E. McKenney <[email protected]>
Reviewed-by: Jeremy Linton <[email protected]>
Tested-by: Jeremy Linton <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
kernel/locking/locktorture.c | 76 +++++++++++++++++++++++++-------------------
1 file changed, 44 insertions(+), 32 deletions(-)
diff --git a/kernel/locking/locktorture.c b/kernel/locking/locktorture.c
index d3de04b12f8c..babc67cfed69 100644
--- a/kernel/locking/locktorture.c
+++ b/kernel/locking/locktorture.c
@@ -641,8 +641,7 @@ static void __torture_print_stats(char *page,
{
bool fail = 0;
int i, n_stress;
- long max = 0;
- long min = statp[0].n_lock_acquired;
+ long max = 0, min = statp ? statp[0].n_lock_acquired : 0;
long long sum = 0;
n_stress = write ? cxt.nrealwriters_stress : cxt.nrealreaders_stress;
@@ -749,7 +748,7 @@ static void lock_torture_cleanup(void)
* such, only perform the underlying torture-specific cleanups,
* and avoid anything related to locktorture.
*/
- if (!cxt.lwsa)
+ if (!cxt.lwsa && !cxt.lrsa)
goto end;
if (writer_tasks) {
@@ -823,6 +822,13 @@ static int __init lock_torture_init(void)
firsterr = -EINVAL;
goto unwind;
}
+
+ if (nwriters_stress == 0 && nreaders_stress == 0) {
+ pr_alert("lock-torture: must run at least one locking thread\n");
+ firsterr = -EINVAL;
+ goto unwind;
+ }
+
if (cxt.cur_ops->init)
cxt.cur_ops->init();
@@ -846,17 +852,19 @@ static int __init lock_torture_init(void)
#endif
/* Initialize the statistics so that each run gets its own numbers. */
+ if (nwriters_stress) {
+ lock_is_write_held = 0;
+ cxt.lwsa = kmalloc(sizeof(*cxt.lwsa) * cxt.nrealwriters_stress, GFP_KERNEL);
+ if (cxt.lwsa == NULL) {
+ VERBOSE_TOROUT_STRING("cxt.lwsa: Out of memory");
+ firsterr = -ENOMEM;
+ goto unwind;
+ }
- lock_is_write_held = 0;
- cxt.lwsa = kmalloc(sizeof(*cxt.lwsa) * cxt.nrealwriters_stress, GFP_KERNEL);
- if (cxt.lwsa == NULL) {
- VERBOSE_TOROUT_STRING("cxt.lwsa: Out of memory");
- firsterr = -ENOMEM;
- goto unwind;
- }
- for (i = 0; i < cxt.nrealwriters_stress; i++) {
- cxt.lwsa[i].n_lock_fail = 0;
- cxt.lwsa[i].n_lock_acquired = 0;
+ for (i = 0; i < cxt.nrealwriters_stress; i++) {
+ cxt.lwsa[i].n_lock_fail = 0;
+ cxt.lwsa[i].n_lock_acquired = 0;
+ }
}
if (cxt.cur_ops->readlock) {
@@ -873,19 +881,21 @@ static int __init lock_torture_init(void)
cxt.nrealreaders_stress = cxt.nrealwriters_stress;
}
- lock_is_read_held = 0;
- cxt.lrsa = kmalloc(sizeof(*cxt.lrsa) * cxt.nrealreaders_stress, GFP_KERNEL);
- if (cxt.lrsa == NULL) {
- VERBOSE_TOROUT_STRING("cxt.lrsa: Out of memory");
- firsterr = -ENOMEM;
- kfree(cxt.lwsa);
- cxt.lwsa = NULL;
- goto unwind;
- }
-
- for (i = 0; i < cxt.nrealreaders_stress; i++) {
- cxt.lrsa[i].n_lock_fail = 0;
- cxt.lrsa[i].n_lock_acquired = 0;
+ if (nreaders_stress) {
+ lock_is_read_held = 0;
+ cxt.lrsa = kmalloc(sizeof(*cxt.lrsa) * cxt.nrealreaders_stress, GFP_KERNEL);
+ if (cxt.lrsa == NULL) {
+ VERBOSE_TOROUT_STRING("cxt.lrsa: Out of memory");
+ firsterr = -ENOMEM;
+ kfree(cxt.lwsa);
+ cxt.lwsa = NULL;
+ goto unwind;
+ }
+
+ for (i = 0; i < cxt.nrealreaders_stress; i++) {
+ cxt.lrsa[i].n_lock_fail = 0;
+ cxt.lrsa[i].n_lock_acquired = 0;
+ }
}
}
@@ -915,12 +925,14 @@ static int __init lock_torture_init(void)
goto unwind;
}
- writer_tasks = kzalloc(cxt.nrealwriters_stress * sizeof(writer_tasks[0]),
- GFP_KERNEL);
- if (writer_tasks == NULL) {
- VERBOSE_TOROUT_ERRSTRING("writer_tasks: Out of memory");
- firsterr = -ENOMEM;
- goto unwind;
+ if (nwriters_stress) {
+ writer_tasks = kzalloc(cxt.nrealwriters_stress * sizeof(writer_tasks[0]),
+ GFP_KERNEL);
+ if (writer_tasks == NULL) {
+ VERBOSE_TOROUT_ERRSTRING("writer_tasks: Out of memory");
+ firsterr = -ENOMEM;
+ goto unwind;
+ }
}
if (cxt.cur_ops->readlock) {
--
2.14.1
From: Josh Poimboeuf <[email protected]>
[ Upstream commit b9eab08d012fa093947b230f9a87257c27fb829b ]
When attempting to load a livepatch module, I got the following error:
module_64: patch_module: Expect noop after relocate, got 3c820000
The error was triggered by the following code in
unregister_netdevice_queue():
14c: 00 00 00 48 b 14c <unregister_netdevice_queue+0x14c>
14c: R_PPC64_REL24 net_set_todo
150: 00 00 82 3c addis r4,r2,0
GCC didn't insert a nop after the branch to net_set_todo() because it's
a sibling call, so it never returns. The nop isn't needed after the
branch in that case.
Signed-off-by: Josh Poimboeuf <[email protected]>
Acked-by: Naveen N. Rao <[email protected]>
Reviewed-and-tested-by: Kamalesh Babulal <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/powerpc/include/asm/code-patching.h | 1 +
arch/powerpc/kernel/module_64.c | 12 +++++++++++-
arch/powerpc/lib/code-patching.c | 5 +++++
3 files changed, 17 insertions(+), 1 deletion(-)
diff --git a/arch/powerpc/include/asm/code-patching.h b/arch/powerpc/include/asm/code-patching.h
index 2015b072422c..b4ab1f497335 100644
--- a/arch/powerpc/include/asm/code-patching.h
+++ b/arch/powerpc/include/asm/code-patching.h
@@ -30,6 +30,7 @@ int patch_branch(unsigned int *addr, unsigned long target, int flags);
int patch_instruction(unsigned int *addr, unsigned int instr);
int instr_is_relative_branch(unsigned int instr);
+int instr_is_relative_link_branch(unsigned int instr);
int instr_is_branch_to_addr(const unsigned int *instr, unsigned long addr);
unsigned long branch_target(const unsigned int *instr);
unsigned int translate_branch(const unsigned int *dest,
diff --git a/arch/powerpc/kernel/module_64.c b/arch/powerpc/kernel/module_64.c
index 183368e008cf..99407cf12ad5 100644
--- a/arch/powerpc/kernel/module_64.c
+++ b/arch/powerpc/kernel/module_64.c
@@ -494,7 +494,17 @@ static bool is_early_mcount_callsite(u32 *instruction)
restore r2. */
static int restore_r2(u32 *instruction, struct module *me)
{
- if (is_early_mcount_callsite(instruction - 1))
+ u32 *prev_insn = instruction - 1;
+
+ if (is_early_mcount_callsite(prev_insn))
+ return 1;
+
+ /*
+ * Make sure the branch isn't a sibling call. Sibling calls aren't
+ * "link" branches and they don't return, so they don't need the r2
+ * restore afterwards.
+ */
+ if (!instr_is_relative_link_branch(*prev_insn))
return 1;
if (*instruction != PPC_INST_NOP) {
diff --git a/arch/powerpc/lib/code-patching.c b/arch/powerpc/lib/code-patching.c
index d5edbeb8eb82..753d591f1b52 100644
--- a/arch/powerpc/lib/code-patching.c
+++ b/arch/powerpc/lib/code-patching.c
@@ -95,6 +95,11 @@ int instr_is_relative_branch(unsigned int instr)
return instr_is_branch_iform(instr) || instr_is_branch_bform(instr);
}
+int instr_is_relative_link_branch(unsigned int instr)
+{
+ return instr_is_relative_branch(instr) && (instr & BRANCH_SET_LINK);
+}
+
static unsigned long branch_iform_target(const unsigned int *instr)
{
signed long imm;
--
2.14.1
From: Mimi Zohar <[email protected]>
[ Upstream commit b7e27bc1d42e8e0cc58b602b529c25cd0071b336 ]
Custom policies can require file signatures based on LSM labels. These
files are normally created and only afterwards labeled, requiring them
to be signed.
Instead of requiring file signatures based on LSM labels, entire
filesystems could require file signatures. In this case, we need the
ability of writing new files without requiring file signatures.
The definition of a "new" file was originally defined as any file with
a length of zero. Subsequent patches redefined a "new" file to be based
on the FILE_CREATE open flag. By combining the open flag with a file
size of zero, this patch relaxes the file signature requirement.
Fixes: 1ac202e978e1 ima: accept previously set IMA_NEW_FILE
Signed-off-by: Mimi Zohar <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
security/integrity/ima/ima_appraise.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/security/integrity/ima/ima_appraise.c b/security/integrity/ima/ima_appraise.c
index 6830d2427e47..7bf8b005a178 100644
--- a/security/integrity/ima/ima_appraise.c
+++ b/security/integrity/ima/ima_appraise.c
@@ -207,7 +207,8 @@ int ima_appraise_measurement(enum ima_hooks func,
if (opened & FILE_CREATED)
iint->flags |= IMA_NEW_FILE;
if ((iint->flags & IMA_NEW_FILE) &&
- !(iint->flags & IMA_DIGSIG_REQUIRED))
+ (!(iint->flags & IMA_DIGSIG_REQUIRED) ||
+ (inode->i_size == 0)))
status = INTEGRITY_PASS;
goto out;
}
--
2.14.1
From: Michael Chan <[email protected]>
[ Upstream commit a8168b6cee6e9334dfebb4b9108e8d73794f6088 ]
On some dual port NICs, the 2 ports have to be configured with compatible
link speeds. Under some conditions, a port's configured speed may no
longer be supported. The firmware will send a message to the driver
when this happens.
Improve this logic that prints out the warning by only printing it if
we can determine the link speed that is no longer supported. If the
speed is unknown or it is in autoneg mode, skip the warning message.
Reported-by: Thomas Bogendoerfer <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Tested-by: Thomas Bogendoerfer <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/broadcom/bnxt/bnxt.c | 10 +++++++---
1 file changed, 7 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bnxt/bnxt.c b/drivers/net/ethernet/broadcom/bnxt/bnxt.c
index bbb3641eddcb..3aa993bbafd9 100644
--- a/drivers/net/ethernet/broadcom/bnxt/bnxt.c
+++ b/drivers/net/ethernet/broadcom/bnxt/bnxt.c
@@ -1498,12 +1498,16 @@ static int bnxt_async_event_process(struct bnxt *bp,
if (BNXT_VF(bp))
goto async_event_process_exit;
- if (data1 & 0x20000) {
+
+ /* print unsupported speed warning in forced speed mode only */
+ if (!(link_info->autoneg & BNXT_AUTONEG_SPEED) &&
+ (data1 & 0x20000)) {
u16 fw_speed = link_info->force_link_speed;
u32 speed = bnxt_fw_to_ethtool_speed(fw_speed);
- netdev_warn(bp->dev, "Link speed %d no longer supported\n",
- speed);
+ if (speed != SPEED_UNKNOWN)
+ netdev_warn(bp->dev, "Link speed %d no longer supported\n",
+ speed);
}
set_bit(BNXT_LINK_SPEED_CHNG_SP_EVENT, &bp->sp_event);
/* fall thru */
--
2.14.1
From: SeongJae Park <[email protected]>
[ Upstream commit 2adfa4210f8f35cdfb4e08318cc06b99752964c2 ]
The 'configinit.sh' script checks the format of optional argument for the
build directory, printing an error message if the format is not valid.
However, the error message uses the wrong variable, indicating an empty
string even though the user entered a non-empty (but erroneous) string.
This commit fixes the script to use the correct variable.
Fixes: c87b9c601ac8 ("rcutorture: Add KVM-based test framework")
Signed-off-by: SeongJae Park <[email protected]>
Signed-off-by: Paul E. McKenney <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/testing/selftests/rcutorture/bin/configinit.sh | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/tools/testing/selftests/rcutorture/bin/configinit.sh b/tools/testing/selftests/rcutorture/bin/configinit.sh
index 3f81a1095206..50a6371b2b2e 100755
--- a/tools/testing/selftests/rcutorture/bin/configinit.sh
+++ b/tools/testing/selftests/rcutorture/bin/configinit.sh
@@ -51,7 +51,7 @@ then
mkdir $builddir
fi
else
- echo Bad build directory: \"$builddir\"
+ echo Bad build directory: \"$buildloc\"
exit 2
fi
fi
--
2.14.1
From: Mahesh Bandewar <[email protected]>
[ Upstream commit 92ff42645028fa6f9b8aa767718457b9264316b4 ]
Packets that don't have dest mac as the mac of the master device should
not be entertained by the IPvlan rx-handler. This is mostly true as the
packet path mostly takes care of that, except when the master device is
a virtual device. As demonstrated in the following case -
ip netns add ns1
ip link add ve1 type veth peer name ve2
ip link add link ve2 name iv1 type ipvlan mode l2
ip link set dev iv1 netns ns1
ip link set ve1 up
ip link set ve2 up
ip -n ns1 link set iv1 up
ip addr add 192.168.10.1/24 dev ve1
ip -n ns1 addr 192.168.10.2/24 dev iv1
ping -c2 192.168.10.2
<Works!>
ip neigh show dev ve1
ip neigh show 192.168.10.2 lladdr <random> dev ve1
ping -c2 192.168.10.2
<Still works! Wrong!!>
This patch adds that missing check in the IPvlan rx-handler.
Reported-by: Amit Sikka <[email protected]>
Signed-off-by: Mahesh Bandewar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ipvlan/ipvlan_core.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/net/ipvlan/ipvlan_core.c b/drivers/net/ipvlan/ipvlan_core.c
index 627eb825eb74..c747ab652665 100644
--- a/drivers/net/ipvlan/ipvlan_core.c
+++ b/drivers/net/ipvlan/ipvlan_core.c
@@ -299,6 +299,10 @@ static int ipvlan_rcv_frame(struct ipvl_addr *addr, struct sk_buff **pskb,
if (dev_forward_skb(ipvlan->dev, skb) == NET_RX_SUCCESS)
success = true;
} else {
+ if (!ether_addr_equal_64bits(eth_hdr(skb)->h_dest,
+ ipvlan->phy_dev->dev_addr))
+ skb->pkt_type = PACKET_OTHERHOST;
+
ret = RX_HANDLER_ANOTHER;
success = true;
}
--
2.14.1
From: Dan Carpenter <[email protected]>
[ Upstream commit 65a12b3aafed5fc59f4ce41b22b752b1729e6701 ]
We should be finishing the loop with timeout set to zero but because
this is a post-op we finish with timeout == -1.
Fixes: 1082e2703a2d ("ASoC: NUC900/audio: add nuc900 audio driver support")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
sound/soc/nuc900/nuc900-ac97.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/sound/soc/nuc900/nuc900-ac97.c b/sound/soc/nuc900/nuc900-ac97.c
index b6615affe571..fde974d52bb2 100644
--- a/sound/soc/nuc900/nuc900-ac97.c
+++ b/sound/soc/nuc900/nuc900-ac97.c
@@ -67,7 +67,7 @@ static unsigned short nuc900_ac97_read(struct snd_ac97 *ac97,
/* polling the AC_R_FINISH */
while (!(AUDIO_READ(nuc900_audio->mmio + ACTL_ACCON) & AC_R_FINISH)
- && timeout--)
+ && --timeout)
mdelay(1);
if (!timeout) {
@@ -121,7 +121,7 @@ static void nuc900_ac97_write(struct snd_ac97 *ac97, unsigned short reg,
/* polling the AC_W_FINISH */
while ((AUDIO_READ(nuc900_audio->mmio + ACTL_ACCON) & AC_W_FINISH)
- && timeout--)
+ && --timeout)
mdelay(1);
if (!timeout)
--
2.14.1
From: Xose Vazquez Perez <[email protected]>
[ Upstream commit 4b3aec2bbbce1c35f50e7475a9fd78d24b9ea4ea ]
Add IBM 3542 and 3552, arrays: FAStT200 and FAStT500.
Add full STK OPENstorage family, arrays: 9176, D173, D178, D210, D220,
D240 and D280.
Add STK BladeCtlr family, arrays: B210, B220, B240 and B280.
These changes were done in multipath-tools time ago.
Cc: NetApp RDAC team <[email protected]>
Cc: Hannes Reinecke <[email protected]>
Cc: Christophe Varoqui <[email protected]>
Cc: Martin K. Petersen <[email protected]>
Cc: James E.J. Bottomley <[email protected]>
Cc: SCSI ML <[email protected]>
Cc: device-mapper development <[email protected]>
Signed-off-by: Xose Vazquez Perez <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/scsi/scsi_dh.c | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/drivers/scsi/scsi_dh.c b/drivers/scsi/scsi_dh.c
index 84addee05be6..a5e30e9449ef 100644
--- a/drivers/scsi/scsi_dh.c
+++ b/drivers/scsi/scsi_dh.c
@@ -56,10 +56,13 @@ static const struct scsi_dh_blist scsi_dh_blist[] = {
{"IBM", "1815", "rdac", },
{"IBM", "1818", "rdac", },
{"IBM", "3526", "rdac", },
+ {"IBM", "3542", "rdac", },
+ {"IBM", "3552", "rdac", },
{"SGI", "TP9", "rdac", },
{"SGI", "IS", "rdac", },
- {"STK", "OPENstorage D280", "rdac", },
+ {"STK", "OPENstorage", "rdac", },
{"STK", "FLEXLINE 380", "rdac", },
+ {"STK", "BladeCtlr", "rdac", },
{"SUN", "CSM", "rdac", },
{"SUN", "LCSM100", "rdac", },
{"SUN", "STK6580_6780", "rdac", },
--
2.14.1
From: Adiel Aloni <[email protected]>
[ Upstream commit e16ea4bb516bc21ea2202f2107718b29218bea59 ]
Enforce using PS_MANUAL_POLL in ps hwsim debugfs to trigger a poll,
only if PS_ENABLED was set before.
This is required due to commit c9491367b759 ("mac80211: always update the
PM state of a peer on MGMT / DATA frames") that enforces the ap to
check only mgmt/data frames ps bit, and then update station's power save
accordingly.
When sending only ps-poll (control frame) the ap will not be aware that
the station entered power save.
Setting ps enable before triggering ps_poll, will send NDP with PM bit
enabled first.
Signed-off-by: Adiel Aloni <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/mac80211_hwsim.c | 17 +++++++++++------
1 file changed, 11 insertions(+), 6 deletions(-)
diff --git a/drivers/net/wireless/mac80211_hwsim.c b/drivers/net/wireless/mac80211_hwsim.c
index 990c857992f6..d12c121806bf 100644
--- a/drivers/net/wireless/mac80211_hwsim.c
+++ b/drivers/net/wireless/mac80211_hwsim.c
@@ -728,16 +728,21 @@ static int hwsim_fops_ps_write(void *dat, u64 val)
val != PS_MANUAL_POLL)
return -EINVAL;
- old_ps = data->ps;
- data->ps = val;
-
- local_bh_disable();
if (val == PS_MANUAL_POLL) {
+ if (data->ps != PS_ENABLED)
+ return -EINVAL;
+ local_bh_disable();
ieee80211_iterate_active_interfaces_atomic(
data->hw, IEEE80211_IFACE_ITER_NORMAL,
hwsim_send_ps_poll, data);
- data->ps_poll_pending = true;
- } else if (old_ps == PS_DISABLED && val != PS_DISABLED) {
+ local_bh_enable();
+ return 0;
+ }
+ old_ps = data->ps;
+ data->ps = val;
+
+ local_bh_disable();
+ if (old_ps == PS_DISABLED && val != PS_DISABLED) {
ieee80211_iterate_active_interfaces_atomic(
data->hw, IEEE80211_IFACE_ITER_NORMAL,
hwsim_send_nullfunc_ps, data);
--
2.14.1
From: Chris Wilson <[email protected]>
[ Upstream commit 8516673a996870ea0ceb337ee4f83c33c5ec3111 ]
Before accessing the GGTT we must flush the PTE writes and make them
visible to the chipset, or else the indirect access may end up in the
wrong page. In commit 3497971a71d8 ("agp/intel: Flush chipset writes
after updating a single PTE"), we noticed corruption of the uploads for
pwrite and for capturing GPU error states, but it was presumed that the
explicit calls to intel_gtt_chipset_flush() were sufficient for the
execbuffer path. However, we have not been flushing the chipset between
the PTE writes and access via the GTT itself.
For simplicity, do the flush after any PTE update rather than try and
batch the flushes on a just-in-time basis.
References: 3497971a71d8 ("agp/intel: Flush chipset writes after updating a single PTE")
Signed-off-by: Chris Wilson <[email protected]>
Cc: Tvrtko Ursulin <[email protected]>
Cc: Mika Kuoppala <[email protected]>
Cc: [email protected]
Reviewed-by: Joonas Lahtinen <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/char/agp/intel-gtt.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/char/agp/intel-gtt.c b/drivers/char/agp/intel-gtt.c
index 0f7d28a98b9a..a7cc5b7be598 100644
--- a/drivers/char/agp/intel-gtt.c
+++ b/drivers/char/agp/intel-gtt.c
@@ -871,6 +871,8 @@ void intel_gtt_insert_sg_entries(struct sg_table *st,
}
}
wmb();
+ if (intel_private.driver->chipset_flush)
+ intel_private.driver->chipset_flush();
}
EXPORT_SYMBOL(intel_gtt_insert_sg_entries);
--
2.14.1
From: Luca Coelho <[email protected]>
[ Upstream commit c7976f5272486e4ff406014c4b43e2fa3b70b052 ]
In the ieee80211_setup_sdata() we check if the interface type is valid
and, if not, call BUG(). This should never happen, but if there is
something wrong with the code, it will not be caught until the bug
happens when an interface is being set up. Calling BUG() is too
extreme for this and a WARN_ON() would be better used instead. Change
that.
Signed-off-by: Luca Coelho <[email protected]>
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
net/mac80211/iface.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/net/mac80211/iface.c b/net/mac80211/iface.c
index a7aa54f45e19..fa7d757fef95 100644
--- a/net/mac80211/iface.c
+++ b/net/mac80211/iface.c
@@ -1520,7 +1520,7 @@ static void ieee80211_setup_sdata(struct ieee80211_sub_if_data *sdata,
break;
case NL80211_IFTYPE_UNSPECIFIED:
case NUM_NL80211_IFTYPES:
- BUG();
+ WARN_ON(1);
break;
}
--
2.14.1
From: Xose Vazquez Perez <[email protected]>
[ Upstream commit b369a0471503130cfc74f9f62071db97f48948c3 ]
Commit 56f3d383f37b ("scsi: scsi_devinfo: Add TRY_VPD_PAGES to HITACHI
OPEN-V blacklist entry") modified some Hitachi entries:
HITACHI is always supporting VPD pages, even though it's claiming to
support SCSI Revision 3 only.
The same should have been done also for HP-rebranded.
[mkp: checkpatch and tweaked commit message]
Cc: Hannes Reinecke <[email protected]>
Cc: Takahiro Yasui <[email protected]>
Cc: Matthias Rudolph <[email protected]>
Cc: Martin K. Petersen <[email protected]>
Cc: James E.J. Bottomley <[email protected]>
Cc: SCSI ML <[email protected]>
Signed-off-by: Xose Vazquez Perez <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/scsi/scsi_devinfo.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/scsi/scsi_devinfo.c b/drivers/scsi/scsi_devinfo.c
index 9545c40daa5e..43d4b30cbf65 100644
--- a/drivers/scsi/scsi_devinfo.c
+++ b/drivers/scsi/scsi_devinfo.c
@@ -180,7 +180,7 @@ static struct {
{"HITACHI", "6586-", "*", BLIST_SPARSELUN | BLIST_LARGELUN},
{"HITACHI", "6588-", "*", BLIST_SPARSELUN | BLIST_LARGELUN},
{"HP", "A6189A", NULL, BLIST_SPARSELUN | BLIST_LARGELUN}, /* HP VA7400 */
- {"HP", "OPEN-", "*", BLIST_REPORTLUN2}, /* HP XP Arrays */
+ {"HP", "OPEN-", "*", BLIST_REPORTLUN2 | BLIST_TRY_VPD_PAGES}, /* HP XP Arrays */
{"HP", "NetRAID-4M", NULL, BLIST_FORCELUN},
{"HP", "HSV100", NULL, BLIST_REPORTLUN2 | BLIST_NOSTARTONADD},
{"HP", "C1557A", NULL, BLIST_FORCELUN},
--
2.14.1
From: Dan Carpenter <[email protected]>
[ Upstream commit d5ac225c7d64c9c3ef821239edc035634e594ec9 ]
The cam->buffers[] array has cam->num_frames elements so the > needs to
be changed to >= to avoid going beyond the end of the array. The
->buffers[] array is allocated in cpia2_allocate_buffers() if you want
to confirm.
Fixes: ab33d5071de7 ("V4L/DVB (3376): Add cpia2 camera support")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/media/usb/cpia2/cpia2_v4l.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/media/usb/cpia2/cpia2_v4l.c b/drivers/media/usb/cpia2/cpia2_v4l.c
index 9caea8344547..d793c630f1dd 100644
--- a/drivers/media/usb/cpia2/cpia2_v4l.c
+++ b/drivers/media/usb/cpia2/cpia2_v4l.c
@@ -812,7 +812,7 @@ static int cpia2_querybuf(struct file *file, void *fh, struct v4l2_buffer *buf)
struct camera_data *cam = video_drvdata(file);
if(buf->type != V4L2_BUF_TYPE_VIDEO_CAPTURE ||
- buf->index > cam->num_frames)
+ buf->index >= cam->num_frames)
return -EINVAL;
buf->m.offset = cam->buffers[buf->index].data - cam->frame_buffer;
@@ -863,7 +863,7 @@ static int cpia2_qbuf(struct file *file, void *fh, struct v4l2_buffer *buf)
if(buf->type != V4L2_BUF_TYPE_VIDEO_CAPTURE ||
buf->memory != V4L2_MEMORY_MMAP ||
- buf->index > cam->num_frames)
+ buf->index >= cam->num_frames)
return -EINVAL;
DBG("QBUF #%d\n", buf->index);
--
2.14.1
From: Julien BOIBESSOT <[email protected]>
[ Upstream commit 77be4c878c72e411ad22af96b6f81dd45c26450a ]
Indeed musl doesn't define old SIGCLD signal name but only new one SIGCHLD.
SIGCHLD is the new POSIX name for that signal so it doesn't change
anything on other libcs.
This fixes this kind of build error:
usbipd.c: In function ‘set_signal’:
usbipd.c:459:12: error: 'SIGCLD' undeclared (first use in this function)
sigaction(SIGCLD, &act, NULL);
^~~~~~
usbipd.c:459:12: note: each undeclared identifier is reported only once
for each function it appears in
Makefile:407: recipe for target 'usbipd.o' failed
make[3]: *** [usbipd.o] Error 1
Signed-off-by: Julien BOIBESSOT <[email protected]>
Acked-by: Shuah Khan <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/usb/usbip/src/usbipd.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/tools/usb/usbip/src/usbipd.c b/tools/usb/usbip/src/usbipd.c
index a0972dea9e6c..193556507957 100644
--- a/tools/usb/usbip/src/usbipd.c
+++ b/tools/usb/usbip/src/usbipd.c
@@ -463,7 +463,7 @@ static void set_signal(void)
sigaction(SIGTERM, &act, NULL);
sigaction(SIGINT, &act, NULL);
act.sa_handler = SIG_IGN;
- sigaction(SIGCLD, &act, NULL);
+ sigaction(SIGCHLD, &act, NULL);
}
static const char *pid_file;
--
2.14.1
From: Ben Greear <[email protected]>
[ Upstream commit 8cec57f5277ef0e354e37a0bf909dc71bc1f865b ]
The 10.4 firmware defines this as a 3-bit field, as does the
mac80211 stack. The 4th bit is defined as CONF_IMPLICIT_BF
at least in the firmware header I have seen. This patch
fixes the ath10k wmi header to match the firmware.
Signed-off-by: Ben Greear <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/ath/ath10k/wmi.h | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/net/wireless/ath/ath10k/wmi.h b/drivers/net/wireless/ath/ath10k/wmi.h
index 1b243c899bef..9b8562ff6698 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.h
+++ b/drivers/net/wireless/ath/ath10k/wmi.h
@@ -5017,7 +5017,8 @@ enum wmi_10_4_vdev_param {
#define WMI_VDEV_PARAM_TXBF_MU_TX_BFER BIT(3)
#define WMI_TXBF_STS_CAP_OFFSET_LSB 4
-#define WMI_TXBF_STS_CAP_OFFSET_MASK 0xf0
+#define WMI_TXBF_STS_CAP_OFFSET_MASK 0x70
+#define WMI_TXBF_CONF_IMPLICIT_BF BIT(7)
#define WMI_BF_SOUND_DIM_OFFSET_LSB 8
#define WMI_BF_SOUND_DIM_OFFSET_MASK 0xf00
--
2.14.1
From: Christophe JAILLET <[email protected]>
[ Upstream commit bf59fddde1c3eab89eb8dca8f3d3dc097887d2bb ]
'ret' is know to be 0 at this point, because it has not been updated by the
the previous call to 'abx500_mask_and_set_register_interruptible()'.
Fix it by updating 'ret' before checking if an error occurred.
Fixes: 84edbeeab67c ("ab8500-charger: AB8500 charger driver")
Signed-off-by: Christophe JAILLET <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/power/supply/ab8500_charger.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/power/supply/ab8500_charger.c b/drivers/power/supply/ab8500_charger.c
index 5cee9aa87aa3..037e93224c38 100644
--- a/drivers/power/supply/ab8500_charger.c
+++ b/drivers/power/supply/ab8500_charger.c
@@ -3218,7 +3218,7 @@ static int ab8500_charger_init_hw_registers(struct ab8500_charger *di)
}
/* Enable backup battery charging */
- abx500_mask_and_set_register_interruptible(di->dev,
+ ret = abx500_mask_and_set_register_interruptible(di->dev,
AB8500_RTC, AB8500_RTC_CTRL_REG,
RTC_BUP_CH_ENA, RTC_BUP_CH_ENA);
if (ret < 0)
--
2.14.1
From: Li Dongyang <[email protected]>
[ Upstream commit 9c0a50022b8ac7e863e6ec8342fa476fe5d1d75c ]
We are testing if there is a match with the ses device in a loop by
calling ses_match_to_enclosure(), which will issue scsi receive
diagnostics commands to the ses device for every device on the same
host. On one of our boxes with 840 disks, it takes a long time to load
the driver:
[root@g1b-oss06 ~]# time modprobe ses
real 40m48.247s
user 0m0.001s
sys 0m0.196s
With the patch:
[root@g1b-oss06 ~]# time modprobe ses
real 0m17.915s
user 0m0.008s
sys 0m0.053s
Note that we still need to refresh page 10 when we see a new disk to
create the link.
Signed-off-by: Li Dongyang <[email protected]>
Tested-by: Jason Ozolins <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/scsi/ses.c | 11 +++++++----
1 file changed, 7 insertions(+), 4 deletions(-)
diff --git a/drivers/scsi/ses.c b/drivers/scsi/ses.c
index f1cdf32d7514..69046d342bc5 100644
--- a/drivers/scsi/ses.c
+++ b/drivers/scsi/ses.c
@@ -578,13 +578,16 @@ static void ses_enclosure_data_process(struct enclosure_device *edev,
}
static void ses_match_to_enclosure(struct enclosure_device *edev,
- struct scsi_device *sdev)
+ struct scsi_device *sdev,
+ int refresh)
{
+ struct scsi_device *edev_sdev = to_scsi_device(edev->edev.parent);
struct efd efd = {
.addr = 0,
};
- ses_enclosure_data_process(edev, to_scsi_device(edev->edev.parent), 0);
+ if (refresh)
+ ses_enclosure_data_process(edev, edev_sdev, 0);
if (scsi_is_sas_rphy(sdev->sdev_target->dev.parent))
efd.addr = sas_get_address(sdev);
@@ -615,7 +618,7 @@ static int ses_intf_add(struct device *cdev,
struct enclosure_device *prev = NULL;
while ((edev = enclosure_find(&sdev->host->shost_gendev, prev)) != NULL) {
- ses_match_to_enclosure(edev, sdev);
+ ses_match_to_enclosure(edev, sdev, 1);
prev = edev;
}
return -ENODEV;
@@ -727,7 +730,7 @@ static int ses_intf_add(struct device *cdev,
shost_for_each_device(tmp_sdev, sdev->host) {
if (tmp_sdev->lun != 0 || scsi_device_enclosure(tmp_sdev))
continue;
- ses_match_to_enclosure(edev, tmp_sdev);
+ ses_match_to_enclosure(edev, tmp_sdev, 0);
}
return 0;
--
2.14.1
From: Kieran Bingham <[email protected]>
[ Upstream commit a17d2d6cd9985ca09a9e384f1bc71d710f7e5203 ]
When used as part of a display pipeline, the VSP is stopped and
restarted explicitly by the DU from its suspend and resume handlers.
There is thus no need to stop or restart pipelines in the VSP suspend
and resume handlers, and doing so would cause the hardware to be
left in a misconfigured state.
Ensure that the VSP suspend and resume handlers do not affect DRM-based
pipelines.
Signed-off-by: Kieran Bingham <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/media/platform/vsp1/vsp1_drv.c | 16 ++++++++++++++--
1 file changed, 14 insertions(+), 2 deletions(-)
diff --git a/drivers/media/platform/vsp1/vsp1_drv.c b/drivers/media/platform/vsp1/vsp1_drv.c
index 57c713a4e1df..4ac1ff482a0b 100644
--- a/drivers/media/platform/vsp1/vsp1_drv.c
+++ b/drivers/media/platform/vsp1/vsp1_drv.c
@@ -509,7 +509,13 @@ static int __maybe_unused vsp1_pm_suspend(struct device *dev)
{
struct vsp1_device *vsp1 = dev_get_drvdata(dev);
- vsp1_pipelines_suspend(vsp1);
+ /*
+ * When used as part of a display pipeline, the VSP is stopped and
+ * restarted explicitly by the DU.
+ */
+ if (!vsp1->drm)
+ vsp1_pipelines_suspend(vsp1);
+
pm_runtime_force_suspend(vsp1->dev);
return 0;
@@ -520,7 +526,13 @@ static int __maybe_unused vsp1_pm_resume(struct device *dev)
struct vsp1_device *vsp1 = dev_get_drvdata(dev);
pm_runtime_force_resume(vsp1->dev);
- vsp1_pipelines_resume(vsp1);
+
+ /*
+ * When used as part of a display pipeline, the VSP is stopped and
+ * restarted explicitly by the DU.
+ */
+ if (!vsp1->drm)
+ vsp1_pipelines_resume(vsp1);
return 0;
}
--
2.14.1
From: Bart Van Assche <[email protected]>
[ Upstream commit a44c9d36509c83cf64f33b93f6ab2e63822c01eb ]
Since scsi_get_device_flags_keyed() callers do not check whether or not
the returned value is an error code, change that function such that it
returns a flags value even if the 'key' argument is invalid. Note:
since commit 28a0bc4120d3 ("scsi: sd: Implement blacklist option for
WRITE SAME w/ UNMAP") bit 31 is a valid device information flag so
checking whether bit 31 is set in the return value is not sufficient to
tell the difference between an error code and a flags value.
Signed-off-by: Bart Van Assche <[email protected]>
Cc: Christoph Hellwig <[email protected]>
Cc: Hannes Reinecke <[email protected]>
Cc: Johannes Thumshirn <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/scsi/scsi_devinfo.c | 7 +------
1 file changed, 1 insertion(+), 6 deletions(-)
diff --git a/drivers/scsi/scsi_devinfo.c b/drivers/scsi/scsi_devinfo.c
index 26e6b05d05fc..9545c40daa5e 100644
--- a/drivers/scsi/scsi_devinfo.c
+++ b/drivers/scsi/scsi_devinfo.c
@@ -596,17 +596,12 @@ int scsi_get_device_flags_keyed(struct scsi_device *sdev,
int key)
{
struct scsi_dev_info_list *devinfo;
- int err;
devinfo = scsi_dev_info_list_find(vendor, model, key);
if (!IS_ERR(devinfo))
return devinfo->flags;
- err = PTR_ERR(devinfo);
- if (err != -ENOENT)
- return err;
-
- /* nothing found, return nothing */
+ /* key or device not found: return nothing */
if (key != SCSI_DEVINFO_GLOBAL)
return 0;
--
2.14.1
From: Limin Zhu <[email protected]>
[ Upstream commit c61cfe49f0f0f0d1f8b56d0b045838d597e8c3a3 ]
(1) Change virtual interface operation in cfg80211 process reset and
reinitilize private data structure.
(2) Scan result event processed in main process will dereference private
data structure concurrently, ocassionly crash the kernel.
The cornel case could be trigger by below steps:
(1) wpa_cli mlan0 scan
(2) ./hostapd mlan0.conf
Cfg80211 asynchronous scan procedure is not all the time operated
under rtnl lock, here we add the protect to serialize the cfg80211
scan and change_virtual interface operation.
Signed-off-by: Limin Zhu <[email protected]>
Signed-off-by: Xinming Hu <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/marvell/mwifiex/cfg80211.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/net/wireless/marvell/mwifiex/cfg80211.c b/drivers/net/wireless/marvell/mwifiex/cfg80211.c
index 8677a53ef725..48d51be11f9b 100644
--- a/drivers/net/wireless/marvell/mwifiex/cfg80211.c
+++ b/drivers/net/wireless/marvell/mwifiex/cfg80211.c
@@ -1109,6 +1109,12 @@ mwifiex_cfg80211_change_virtual_intf(struct wiphy *wiphy,
struct mwifiex_private *priv = mwifiex_netdev_get_priv(dev);
enum nl80211_iftype curr_iftype = dev->ieee80211_ptr->iftype;
+ if (priv->scan_request) {
+ mwifiex_dbg(priv->adapter, ERROR,
+ "change virtual interface: scan in process\n");
+ return -EBUSY;
+ }
+
switch (curr_iftype) {
case NL80211_IFTYPE_ADHOC:
switch (type) {
--
2.14.1
From: Peter Ujfalusi <[email protected]>
[ Upstream commit de92436ac40ffe9933230aa503e24dbb5ede9201 ]
To avoid race with vchan_complete, use the race free way to terminate
running transfer.
Implement the device_synchronize callback to make sure that the terminated
descriptor is freed.
Signed-off-by: Peter Ujfalusi <[email protected]>
Acked-by: Eric Anholt <[email protected]>
Signed-off-by: Vinod Koul <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/dma/bcm2835-dma.c | 10 +++++++++-
1 file changed, 9 insertions(+), 1 deletion(-)
diff --git a/drivers/dma/bcm2835-dma.c b/drivers/dma/bcm2835-dma.c
index 6204cc32d09c..847f84a41a69 100644
--- a/drivers/dma/bcm2835-dma.c
+++ b/drivers/dma/bcm2835-dma.c
@@ -812,7 +812,7 @@ static int bcm2835_dma_terminate_all(struct dma_chan *chan)
* c->desc is NULL and exit.)
*/
if (c->desc) {
- bcm2835_dma_desc_free(&c->desc->vd);
+ vchan_terminate_vdesc(&c->desc->vd);
c->desc = NULL;
bcm2835_dma_abort(c->chan_base);
@@ -836,6 +836,13 @@ static int bcm2835_dma_terminate_all(struct dma_chan *chan)
return 0;
}
+static void bcm2835_dma_synchronize(struct dma_chan *chan)
+{
+ struct bcm2835_chan *c = to_bcm2835_dma_chan(chan);
+
+ vchan_synchronize(&c->vc);
+}
+
static int bcm2835_dma_chan_init(struct bcm2835_dmadev *d, int chan_id,
int irq, unsigned int irq_flags)
{
@@ -942,6 +949,7 @@ static int bcm2835_dma_probe(struct platform_device *pdev)
od->ddev.device_prep_dma_memcpy = bcm2835_dma_prep_dma_memcpy;
od->ddev.device_config = bcm2835_dma_slave_config;
od->ddev.device_terminate_all = bcm2835_dma_terminate_all;
+ od->ddev.device_synchronize = bcm2835_dma_synchronize;
od->ddev.src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES);
od->ddev.dst_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES);
od->ddev.directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV) |
--
2.14.1
From: "Rafael J. Wysocki" <[email protected]>
[ Upstream commit a8b149d32b663c1a4105273295184b78f53d33cf ]
It is possible to remove a cpufreq governor module after
cpufreq_parse_governor() has returned success in
store_scaling_governor() and before cpufreq_set_policy()
acquires a reference to it, because the governor list is
not protected during that period and nothing prevents the
governor from being unregistered then.
Prevent that from happening by acquiring an extra reference
to the governor module temporarily in cpufreq_parse_governor(),
under cpufreq_governor_mutex, and dropping it in
store_scaling_governor(), when cpufreq_set_policy() returns.
Note that the second cpufreq_parse_governor() call site is fine,
because it only cares about the policy member of new_policy.
Signed-off-by: Rafael J. Wysocki <[email protected]>
Acked-by: Viresh Kumar <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/cpufreq/cpufreq.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/cpufreq/cpufreq.c b/drivers/cpufreq/cpufreq.c
index 35e34c0e0429..94d42448d403 100644
--- a/drivers/cpufreq/cpufreq.c
+++ b/drivers/cpufreq/cpufreq.c
@@ -605,6 +605,8 @@ static int cpufreq_parse_governor(char *str_governor, unsigned int *policy,
*governor = t;
err = 0;
}
+ if (t && !try_module_get(t->owner))
+ t = NULL;
mutex_unlock(&cpufreq_governor_mutex);
}
@@ -723,6 +725,10 @@ static ssize_t store_scaling_governor(struct cpufreq_policy *policy,
return -EINVAL;
ret = cpufreq_set_policy(policy, &new_policy);
+
+ if (new_policy.governor)
+ module_put(new_policy.governor->owner);
+
return ret ? ret : count;
}
--
2.14.1
From: Axel Lin <[email protected]>
[ Upstream commit 8472b529e113e0863ea064fdee51bf73c3f86fd6 ]
Fix trivial copy/paste bug.
Signed-off-by: Axel Lin <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Fixes: ef1f09eca74a ("pwm: Add a driver for the STMPE PWM")
Signed-off-by: Thierry Reding <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/pwm/pwm-stmpe.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/pwm/pwm-stmpe.c b/drivers/pwm/pwm-stmpe.c
index e464582a390a..3439f1e902cb 100644
--- a/drivers/pwm/pwm-stmpe.c
+++ b/drivers/pwm/pwm-stmpe.c
@@ -145,7 +145,7 @@ static int stmpe_24xx_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
break;
case 2:
- offset = STMPE24XX_PWMIC1;
+ offset = STMPE24XX_PWMIC2;
break;
default:
--
2.14.1
From: Stephen Hemminger <[email protected]>
[ Upstream commit 72d24955b44a4039db54a1c252b5031969eeaac3 ]
When new veth is created, and GSO values have been configured
on one device, clone those values to the peer.
For example:
# ip link add dev vm1 gso_max_size 65530 type veth peer name vm2
This should create vm1 <--> vm2 with both having GSO maximum
size set to 65530.
Signed-off-by: Stephen Hemminger <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/veth.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/net/veth.c b/drivers/net/veth.c
index fbc853e64531..ee7460ee3d05 100644
--- a/drivers/net/veth.c
+++ b/drivers/net/veth.c
@@ -425,6 +425,9 @@ static int veth_newlink(struct net *src_net, struct net_device *dev,
if (ifmp && (dev->ifindex != 0))
peer->ifindex = ifmp->ifi_index;
+ peer->gso_max_size = dev->gso_max_size;
+ peer->gso_max_segs = dev->gso_max_segs;
+
err = register_netdevice(peer);
put_net(net);
net = NULL;
--
2.14.1
From: Christophe JAILLET <[email protected]>
[ Upstream commit 09edcb647542487864e23aa8d2ef26be3e08978a ]
If an error occurs when we enable the backup battery charging, we should
go through the error handling path directly.
Before commit db43e6c473b5 ("ab8500-bm: Add usb power path support") this
was the case, but this commit has added some code between the last test and
the 'out' label.
So, in case of error, this added code is executed and the error may be
silently ignored.
Fix it by adding the missing 'goto out', as done in all other error
handling paths.
Fixes: db43e6c473b5 ("ab8500-bm: Add usb power path support")
Signed-off-by: Christophe JAILLET <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/power/supply/ab8500_charger.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/power/supply/ab8500_charger.c b/drivers/power/supply/ab8500_charger.c
index 037e93224c38..48a11fd86a7f 100644
--- a/drivers/power/supply/ab8500_charger.c
+++ b/drivers/power/supply/ab8500_charger.c
@@ -3221,8 +3221,10 @@ static int ab8500_charger_init_hw_registers(struct ab8500_charger *di)
ret = abx500_mask_and_set_register_interruptible(di->dev,
AB8500_RTC, AB8500_RTC_CTRL_REG,
RTC_BUP_CH_ENA, RTC_BUP_CH_ENA);
- if (ret < 0)
+ if (ret < 0) {
dev_err(di->dev, "%s mask and set failed\n", __func__);
+ goto out;
+ }
if (is_ab8540(di->parent)) {
ret = abx500_mask_and_set_register_interruptible(di->dev,
--
2.14.1
From: Bjorn Andersson <[email protected]>
[ Upstream commit 8f52df50d9366f770a894d14ef724e5e04574e98 ]
The pointer returned by of_device_get_match_data() doesn't have the same
size as u32 on 64-bit architectures, causing a compile warning when
compile-testing the driver on such platform.
Cast the return value of of_device_get_match_data() to unsigned long and
then to u32 to silence this warning.
Fixes: 7f866986e705 ("leds: add PM8058 LEDs driver")
Signed-off-by: Bjorn Andersson <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/leds/leds-pm8058.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/leds/leds-pm8058.c b/drivers/leds/leds-pm8058.c
index a52674327857..8988ba3b2d65 100644
--- a/drivers/leds/leds-pm8058.c
+++ b/drivers/leds/leds-pm8058.c
@@ -106,7 +106,7 @@ static int pm8058_led_probe(struct platform_device *pdev)
if (!led)
return -ENOMEM;
- led->ledtype = (u32)of_device_get_match_data(&pdev->dev);
+ led->ledtype = (u32)(unsigned long)of_device_get_match_data(&pdev->dev);
map = dev_get_regmap(pdev->dev.parent, NULL);
if (!map) {
--
2.14.1
From: "Andrew F. Davis" <[email protected]>
[ Upstream commit e153db03c6b7a035c797bcdf35262586f003ee93 ]
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Fixes: 4341881d0562 ("ARM: dts: Add devicetree for Gumstix Pepper board")
Signed-off-by: Andrew F. Davis <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/am335x-pepper.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/am335x-pepper.dts b/arch/arm/boot/dts/am335x-pepper.dts
index 30e2f8770aaf..42b62f54e4b7 100644
--- a/arch/arm/boot/dts/am335x-pepper.dts
+++ b/arch/arm/boot/dts/am335x-pepper.dts
@@ -139,7 +139,7 @@
&audio_codec {
status = "okay";
- gpio-reset = <&gpio1 16 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
AVDD-supply = <&ldo3_reg>;
IOVDD-supply = <&ldo3_reg>;
DRVDD-supply = <&ldo3_reg>;
--
2.14.1
From: Manikanta Pubbisetty <[email protected]>
[ Upstream commit 424ea0d174e82365f85c6770225dba098b8f1d5f ]
It is required to update the teardown state of the peer when
a tdls link with that peer is terminated. This information is
useful for the target to perform some cleanups wrt the tdls peer.
Without proper cleanup, target assumes that the peer is connected and
blocks future connection requests, updating the teardown state of the
peer addresses the problem.
Tested this change on QCA9888 with 10.4-3.5.1-00018 fw version.
Signed-off-by: Manikanta Pubbisetty <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/ath/ath10k/mac.c | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 696b90270615..1e6e63dbd61c 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -6054,6 +6054,16 @@ static int ath10k_sta_state(struct ieee80211_hw *hw,
"mac vdev %d peer delete %pM sta %pK (sta gone)\n",
arvif->vdev_id, sta->addr, sta);
+ if (sta->tdls) {
+ ret = ath10k_mac_tdls_peer_update(ar, arvif->vdev_id,
+ sta,
+ WMI_TDLS_PEER_STATE_TEARDOWN);
+ if (ret)
+ ath10k_warn(ar, "failed to update tdls peer state for %pM state %d: %i\n",
+ sta->addr,
+ WMI_TDLS_PEER_STATE_TEARDOWN, ret);
+ }
+
ret = ath10k_peer_delete(ar, arvif->vdev_id, sta->addr);
if (ret)
ath10k_warn(ar, "failed to delete peer %pM for vdev %d: %i\n",
--
2.14.1
From: Sunil Goutham <[email protected]>
[ Upstream commit 87de083857aa269fb171ef0b39696b2888361c58 ]
on T81 there are only 4 cores, hence setting max queue count to 4
would leave nothing for XDP_TX. This patch fixes this by doubling
max queue count in above scenarios.
Signed-off-by: Sunil Goutham <[email protected]>
Signed-off-by: cjacob <[email protected]>
Signed-off-by: Aleksey Makarov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/cavium/thunder/nicvf_main.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/drivers/net/ethernet/cavium/thunder/nicvf_main.c b/drivers/net/ethernet/cavium/thunder/nicvf_main.c
index 8a37012c9c89..c75d4ea9342b 100644
--- a/drivers/net/ethernet/cavium/thunder/nicvf_main.c
+++ b/drivers/net/ethernet/cavium/thunder/nicvf_main.c
@@ -1576,6 +1576,11 @@ static int nicvf_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
nic->pdev = pdev;
nic->pnicvf = nic;
nic->max_queues = qcount;
+ /* If no of CPUs are too low, there won't be any queues left
+ * for XDP_TX, hence double it.
+ */
+ if (!nic->t88)
+ nic->max_queues *= 2;
/* MAP VF's configuration registers */
nic->reg_base = pcim_iomap(pdev, PCI_CFG_REG_BAR_NUM, 0);
--
2.14.1
From: "Andrew F. Davis" <[email protected]>
[ Upstream commit 7be4b5dc7ffa9499ac6ef33a5ffa9ff43f9b7057 ]
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Fixes: 14e3e295b2b9 ("ARM: dts: omap3-n900: Add TLV320AIC3X support")
Signed-off-by: Andrew F. Davis <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/omap3-n900.dts | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index 4d448f145ed1..6003b29c0fc0 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -510,7 +510,7 @@
tlv320aic3x: tlv320aic3x@18 {
compatible = "ti,tlv320aic3x";
reg = <0x18>;
- gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
+ reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; /* 60 */
ai3x-gpio-func = <
0 /* AIC3X_GPIO1_FUNC_DISABLED */
5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
@@ -527,7 +527,7 @@
tlv320aic3x_aux: tlv320aic3x@19 {
compatible = "ti,tlv320aic3x";
reg = <0x19>;
- gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
+ reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; /* 60 */
AVDD-supply = <&vmmc2>;
DRVDD-supply = <&vmmc2>;
--
2.14.1
From: "Eric W. Biederman" <[email protected]>
[ Upstream commit bbc3e471011417598e598707486f5d8814ec9c01 ]
When vfs_submount was added the test to limit automounts from
filesystems that with s_user_ns != &init_user_ns accidentially left
in follow_automount. The test was never about any security concerns
and was always about how do we implement this for filesystems whose
s_user_ns != &init_user_ns.
At the moment this check makes no difference as there are no
filesystems that both set FS_USERNS_MOUNT and implement d_automount.
Remove this check now while I am thinking about it so there will not
be odd booby traps for someone who does want to make this combination
work.
vfs_submount still needs improvements to allow this combination to work,
and vfs_submount contains a check that presents a warning.
The autofs4 filesystem could be modified to set FS_USERNS_MOUNT and it would
need not work on this code path, as userspace performs the mounts.
Fixes: 93faccbbfa95 ("fs: Better permission checking for submounts")
Fixes: aeaa4a79ff6a ("fs: Call d_automount with the filesystems creds")
Acked-by: Ian Kent <[email protected]>
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
fs/namei.c | 3 ---
1 file changed, 3 deletions(-)
diff --git a/fs/namei.c b/fs/namei.c
index 6cfb45f262aa..917e7996b9c3 100644
--- a/fs/namei.c
+++ b/fs/namei.c
@@ -1121,9 +1121,6 @@ static int follow_automount(struct path *path, struct nameidata *nd,
path->dentry->d_inode)
return -EISDIR;
- if (path->dentry->d_sb->s_user_ns != &init_user_ns)
- return -EACCES;
-
nd->total_link_count++;
if (nd->total_link_count >= 40)
return -ELOOP;
--
2.14.1
From: Lorenzo Colitti <[email protected]>
[ Upstream commit be8f8284cd897af2482d4e54fbc2bdfc15557259 ]
Currently it is possible to add or update socket policies, but
not clear them. Therefore, once a socket policy has been applied,
the socket cannot be used for unencrypted traffic.
This patch allows (privileged) users to clear socket policies by
passing in a NULL pointer and zero length argument to the
{IP,IPV6}_{IPSEC,XFRM}_POLICY setsockopts. This results in both
the incoming and outgoing policies being cleared.
The simple approach taken in this patch cannot clear socket
policies in only one direction. If desired this could be added
in the future, for example by continuing to pass in a length of
zero (which currently is guaranteed to return EMSGSIZE) and
making the policy be a pointer to an integer that contains one
of the XFRM_POLICY_{IN,OUT} enum values.
An alternative would have been to interpret the length as a
signed integer and use XFRM_POLICY_IN (i.e., 0) to clear the
input policy and -XFRM_POLICY_OUT (i.e., -1) to clear the output
policy.
Tested: https://android-review.googlesource.com/539816
Signed-off-by: Lorenzo Colitti <[email protected]>
Signed-off-by: Steffen Klassert <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
net/xfrm/xfrm_policy.c | 2 +-
net/xfrm/xfrm_state.c | 7 +++++++
2 files changed, 8 insertions(+), 1 deletion(-)
diff --git a/net/xfrm/xfrm_policy.c b/net/xfrm/xfrm_policy.c
index 5e89b7461f99..5b8fa6832687 100644
--- a/net/xfrm/xfrm_policy.c
+++ b/net/xfrm/xfrm_policy.c
@@ -1346,7 +1346,7 @@ EXPORT_SYMBOL(xfrm_policy_delete);
int xfrm_sk_policy_insert(struct sock *sk, int dir, struct xfrm_policy *pol)
{
- struct net *net = xp_net(pol);
+ struct net *net = sock_net(sk);
struct xfrm_policy *old_pol;
#ifdef CONFIG_XFRM_SUB_POLICY
diff --git a/net/xfrm/xfrm_state.c b/net/xfrm/xfrm_state.c
index 419bf5d463bd..13e0611a9085 100644
--- a/net/xfrm/xfrm_state.c
+++ b/net/xfrm/xfrm_state.c
@@ -1883,6 +1883,13 @@ int xfrm_user_policy(struct sock *sk, int optname, u8 __user *optval, int optlen
struct xfrm_mgr *km;
struct xfrm_policy *pol = NULL;
+ if (!optval && !optlen) {
+ xfrm_sk_policy_insert(sk, XFRM_POLICY_IN, NULL);
+ xfrm_sk_policy_insert(sk, XFRM_POLICY_OUT, NULL);
+ __sk_dst_reset(sk);
+ return 0;
+ }
+
if (optlen <= 0 || optlen > PAGE_SIZE)
return -EMSGSIZE;
--
2.14.1
From: Jagdish Gediya <[email protected]>
[ Upstream commit bccb06c353af3764ca86d9da47652458e6c2eb41 ]
Bufnum mask is used to calculate page position in the internal SRAM.
As IFC version 2.0.0 has 16KB of internal SRAM as compared to older
versions which had 8KB. Hence bufnum mask needs to be updated.
Signed-off-by: Jagdish Gediya <[email protected]>
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/mtd/nand/fsl_ifc_nand.c | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/drivers/mtd/nand/fsl_ifc_nand.c b/drivers/mtd/nand/fsl_ifc_nand.c
index d1570f512f0b..f8f12ccc6471 100644
--- a/drivers/mtd/nand/fsl_ifc_nand.c
+++ b/drivers/mtd/nand/fsl_ifc_nand.c
@@ -907,6 +907,13 @@ static int fsl_ifc_chip_init(struct fsl_ifc_mtd *priv)
if (ctrl->version == FSL_IFC_VERSION_1_1_0)
fsl_ifc_sram_init(priv);
+ /*
+ * As IFC version 2.0.0 has 16KB of internal SRAM as compared to older
+ * versions which had 8KB. Hence bufnum mask needs to be updated.
+ */
+ if (ctrl->version >= FSL_IFC_VERSION_2_0_0)
+ priv->bufnum_mask = (priv->bufnum_mask * 2) + 1;
+
return 0;
}
--
2.14.1
From: Miquel Raynal <[email protected]>
[ Upstream commit df467899da0b71465760b4e35127bce837244eee ]
Some drivers (like nand_hynix.c) call ->cmdfunc() with NAND_CMD_NONE
and a column address and expect the controller to only send address
cycles. Right now, the default ->cmdfunc() implementations provided by
the core do not filter out the command cycle in this case and forwards
the request to the controller driver through the ->cmd_ctrl() method.
The thing is, NAND controller drivers can get this wrong and send a
command cycle with a NAND_CMD_NONE opcode and since NAND_CMD_NONE is
-1, and the command field is usually casted to an u8, we end up sending
the 0xFF command which is actually a RESET operation.
Add conditions in nand_command[_lp]() functions to sending the initial
command cycle when command == NAND_CMD_NONE.
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/mtd/nand/nand_base.c | 9 +++++++--
1 file changed, 7 insertions(+), 2 deletions(-)
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index 21c03086bb7f..a3e86e52640a 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -715,7 +715,8 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
chip->cmd_ctrl(mtd, readcmd, ctrl);
ctrl &= ~NAND_CTRL_CHANGE;
}
- chip->cmd_ctrl(mtd, command, ctrl);
+ if (command != NAND_CMD_NONE)
+ chip->cmd_ctrl(mtd, command, ctrl);
/* Address cycle, when necessary */
ctrl = NAND_CTRL_ALE | NAND_CTRL_CHANGE;
@@ -744,6 +745,7 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
*/
switch (command) {
+ case NAND_CMD_NONE:
case NAND_CMD_PAGEPROG:
case NAND_CMD_ERASE1:
case NAND_CMD_ERASE2:
@@ -806,7 +808,9 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
}
/* Command latch cycle */
- chip->cmd_ctrl(mtd, command, NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE);
+ if (command != NAND_CMD_NONE)
+ chip->cmd_ctrl(mtd, command,
+ NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE);
if (column != -1 || page_addr != -1) {
int ctrl = NAND_CTRL_CHANGE | NAND_NCE | NAND_ALE;
@@ -842,6 +846,7 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
*/
switch (command) {
+ case NAND_CMD_NONE:
case NAND_CMD_CACHEDPROG:
case NAND_CMD_PAGEPROG:
case NAND_CMD_ERASE1:
--
2.14.1
From: Ganapathi Bhat <[email protected]>
[ Upstream commit ecd7eb7c2bcf99f6c23d68ad56ce15949da848a1 ]
We have to use start port, for TX/RX of single packet,
instead of current aggregating port. This will fix SDIO
CMD53(TX/RX) returning -ETIMEDOUT and halting the data path.
Fixes: 0cb52aac4d19 ("mwifiex: do not set multiport flag for tx/rx single packet")
Signed-off-by: Ganapathi Bhat <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/marvell/mwifiex/sdio.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/marvell/mwifiex/sdio.c b/drivers/net/wireless/marvell/mwifiex/sdio.c
index 8d601dcf2948..486b8c75cd1f 100644
--- a/drivers/net/wireless/marvell/mwifiex/sdio.c
+++ b/drivers/net/wireless/marvell/mwifiex/sdio.c
@@ -1458,7 +1458,7 @@ static int mwifiex_sdio_card_to_host_mp_aggr(struct mwifiex_adapter *adapter,
}
if (card->mpa_rx.pkt_cnt == 1)
- mport = adapter->ioport + port;
+ mport = adapter->ioport + card->mpa_rx.start_port;
if (mwifiex_read_data_sync(adapter, card->mpa_rx.buf,
card->mpa_rx.buf_len, mport, 1))
@@ -1891,7 +1891,7 @@ static int mwifiex_host_to_card_mp_aggr(struct mwifiex_adapter *adapter,
}
if (card->mpa_tx.pkt_cnt == 1)
- mport = adapter->ioport + port;
+ mport = adapter->ioport + card->mpa_tx.start_port;
ret = mwifiex_write_data_to_card(adapter, card->mpa_tx.buf,
card->mpa_tx.buf_len, mport);
--
2.14.1
From: Michael Hennerich <[email protected]>
[ Upstream commit 388b3b2b03701f3b3c10975c272892d7f78080df ]
This fixes undefined reference to struct adf7242_local *lp in
case DEBUG is defined.
Signed-off-by: Michael Hennerich <[email protected]>
Signed-off-by: Stefan Schmidt <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ieee802154/adf7242.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ieee802154/adf7242.c b/drivers/net/ieee802154/adf7242.c
index f355df7cf84a..1b980f12663a 100644
--- a/drivers/net/ieee802154/adf7242.c
+++ b/drivers/net/ieee802154/adf7242.c
@@ -888,7 +888,7 @@ static struct ieee802154_ops adf7242_ops = {
.set_cca_ed_level = adf7242_set_cca_ed_level,
};
-static void adf7242_debug(u8 irq1)
+static void adf7242_debug(struct adf7242_local *lp, u8 irq1)
{
#ifdef DEBUG
u8 stat;
@@ -932,7 +932,7 @@ static irqreturn_t adf7242_isr(int irq, void *data)
dev_err(&lp->spi->dev, "%s :ERROR IRQ1 = 0x%X\n",
__func__, irq1);
- adf7242_debug(irq1);
+ adf7242_debug(lp, irq1);
xmit = test_bit(FLAG_XMIT, &lp->flags);
--
2.14.1
From: Stephane Eranian <[email protected]>
[ Upstream commit db49a71798a38f3ddf3f3462703328dca39b1ac7 ]
(This is a patch has been sitting in the Intel CQM/CMT driver series for
a while, despite not depend on it. Sending it now independently since
the series is being discarded.)
When an event is in error state, read() returns 0 instead of sizeof()
buffer. In certain modes, such as interval printing, ignoring the 0
return value may cause bogus count deltas to be computed and thus
invalid results printed.
This patch fixes this problem by modifying read_counters() to mark the
event as not scaled (scaled = -1) to force the printout routine to show
<NOT COUNTED>.
Signed-off-by: Stephane Eranian <[email protected]>
Reviewed-by: David Carrillo-Cisneros <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Adrian Hunter <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Mathieu Poirier <[email protected]>
Cc: Paul Turner <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/perf/builtin-stat.c | 12 +++++++++---
tools/perf/util/evsel.c | 4 ++--
2 files changed, 11 insertions(+), 5 deletions(-)
diff --git a/tools/perf/builtin-stat.c b/tools/perf/builtin-stat.c
index c241167c76c9..5b60ec669e73 100644
--- a/tools/perf/builtin-stat.c
+++ b/tools/perf/builtin-stat.c
@@ -311,8 +311,12 @@ static int read_counter(struct perf_evsel *counter)
struct perf_counts_values *count;
count = perf_counts(counter->counts, cpu, thread);
- if (perf_evsel__read(counter, cpu, thread, count))
+ if (perf_evsel__read(counter, cpu, thread, count)) {
+ counter->counts->scaled = -1;
+ perf_counts(counter->counts, cpu, thread)->ena = 0;
+ perf_counts(counter->counts, cpu, thread)->run = 0;
return -1;
+ }
if (STAT_RECORD) {
if (perf_evsel__write_stat_event(counter, cpu, thread, count)) {
@@ -337,12 +341,14 @@ static int read_counter(struct perf_evsel *counter)
static void read_counters(void)
{
struct perf_evsel *counter;
+ int ret;
evlist__for_each_entry(evsel_list, counter) {
- if (read_counter(counter))
+ ret = read_counter(counter);
+ if (ret)
pr_debug("failed to read counter %s\n", counter->name);
- if (perf_stat_process_counter(&stat_config, counter))
+ if (ret == 0 && perf_stat_process_counter(&stat_config, counter))
pr_warning("failed to process counter %s\n", counter->name);
}
}
diff --git a/tools/perf/util/evsel.c b/tools/perf/util/evsel.c
index 539724c7d30b..bce80f866dd0 100644
--- a/tools/perf/util/evsel.c
+++ b/tools/perf/util/evsel.c
@@ -1221,7 +1221,7 @@ int perf_evsel__read(struct perf_evsel *evsel, int cpu, int thread,
if (FD(evsel, cpu, thread) < 0)
return -EINVAL;
- if (readn(FD(evsel, cpu, thread), count, sizeof(*count)) < 0)
+ if (readn(FD(evsel, cpu, thread), count, sizeof(*count)) <= 0)
return -errno;
return 0;
@@ -1239,7 +1239,7 @@ int __perf_evsel__read_on_cpu(struct perf_evsel *evsel,
if (evsel->counts == NULL && perf_evsel__alloc_counts(evsel, cpu + 1, thread + 1) < 0)
return -ENOMEM;
- if (readn(FD(evsel, cpu, thread), &count, nv * sizeof(u64)) < 0)
+ if (readn(FD(evsel, cpu, thread), &count, nv * sizeof(u64)) <= 0)
return -errno;
perf_evsel__compute_deltas(evsel, cpu, thread, &count);
--
2.14.1
From: Dedy Lansky <[email protected]>
[ Upstream commit 0f6edfe2bbbb59d161580cb4870fcc46f5490f85 ]
In case count is not multiple of 4, there is a read access in
wil_memcpy_toio_32() from outside src buffer boundary.
In wil_memcpy_fromio_32(), in case count is not multiple of 4, there is
a write access to outside dst io memory boundary.
Fix these issues with proper handling of the last 1 to 4 copied bytes.
Signed-off-by: Dedy Lansky <[email protected]>
Signed-off-by: Maya Erez <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/ath/wil6210/main.c | 20 +++++++++++++++++---
1 file changed, 17 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/ath/wil6210/main.c b/drivers/net/wireless/ath/wil6210/main.c
index 24b07a0ce6f7..f8bce58d48cc 100644
--- a/drivers/net/wireless/ath/wil6210/main.c
+++ b/drivers/net/wireless/ath/wil6210/main.c
@@ -129,9 +129,15 @@ void wil_memcpy_fromio_32(void *dst, const volatile void __iomem *src,
u32 *d = dst;
const volatile u32 __iomem *s = src;
- /* size_t is unsigned, if (count%4 != 0) it will wrap */
- for (count += 4; count > 4; count -= 4)
+ for (; count >= 4; count -= 4)
*d++ = __raw_readl(s++);
+
+ if (unlikely(count)) {
+ /* count can be 1..3 */
+ u32 tmp = __raw_readl(s);
+
+ memcpy(d, &tmp, count);
+ }
}
void wil_memcpy_fromio_halp_vote(struct wil6210_priv *wil, void *dst,
@@ -148,8 +154,16 @@ void wil_memcpy_toio_32(volatile void __iomem *dst, const void *src,
volatile u32 __iomem *d = dst;
const u32 *s = src;
- for (count += 4; count > 4; count -= 4)
+ for (; count >= 4; count -= 4)
__raw_writel(*s++, d++);
+
+ if (unlikely(count)) {
+ /* count can be 1..3 */
+ u32 tmp = 0;
+
+ memcpy(&tmp, s, count);
+ __raw_writel(tmp, d);
+ }
}
void wil_memcpy_toio_halp_vote(struct wil6210_priv *wil,
--
2.14.1
From: "Maciej S. Szmigiero" <[email protected]>
[ Upstream commit 01ca485171e3253f3aee555437519c0d316d4b0c ]
We need to make sure that only proper channel slots (in SACCST register)
are enabled at playback start time since some AC'97 CODECs (like VT1613 on
UDOO board) were observed requesting via SLOTREQ spurious ones just after
an AC'97 link is started but before the CODEC is configured by its driver.
When a bit for some channel slot is set in a SLOTREQ request then SSI sets
the relevant bit in SACCST automatically, which then 'sticks' until it is
manually unset.
The SACCST register is not writable directly, we have to use SACCDIS and
SACCEN registers to configure it instead (these aren't normal registers:
writing a '1' bit at some position in SACCEN sets the relevant bit in
SACCST; SACCDIS operates in a similar way but allows unsetting bits in
SACCST).
Theoretically, this should be necessary only for the very first playback
but since some CODECs are so untrustworthy and extra channel slots enabled
mean ruined playback let's play safe here and make sure that no extra
slots are enabled in SACCST every time a playback is started.
Signed-off-by: Maciej S. Szmigiero <[email protected]>
Acked-by: Nicolin Chen <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
sound/soc/fsl/fsl_ssi.c | 52 +++++++++++++++++++++++++++++++++++++++++++------
1 file changed, 46 insertions(+), 6 deletions(-)
diff --git a/sound/soc/fsl/fsl_ssi.c b/sound/soc/fsl/fsl_ssi.c
index 1c03490e1182..53e6c42e82f0 100644
--- a/sound/soc/fsl/fsl_ssi.c
+++ b/sound/soc/fsl/fsl_ssi.c
@@ -581,8 +581,54 @@ static void fsl_ssi_rx_config(struct fsl_ssi_private *ssi_private, bool enable)
fsl_ssi_config(ssi_private, enable, &ssi_private->rxtx_reg_val.rx);
}
+static void fsl_ssi_tx_ac97_saccst_setup(struct fsl_ssi_private *ssi_private)
+{
+ struct regmap *regs = ssi_private->regs;
+
+ /* no SACC{ST,EN,DIS} regs on imx21-class SSI */
+ if (!ssi_private->soc->imx21regs) {
+ /*
+ * Note that these below aren't just normal registers.
+ * They are a way to disable or enable bits in SACCST
+ * register:
+ * - writing a '1' bit at some position in SACCEN sets the
+ * relevant bit in SACCST,
+ * - writing a '1' bit at some position in SACCDIS unsets
+ * the relevant bit in SACCST register.
+ *
+ * The two writes below first disable all channels slots,
+ * then enable just slots 3 & 4 ("PCM Playback Left Channel"
+ * and "PCM Playback Right Channel").
+ */
+ regmap_write(regs, CCSR_SSI_SACCDIS, 0xff);
+ regmap_write(regs, CCSR_SSI_SACCEN, 0x300);
+ }
+}
+
static void fsl_ssi_tx_config(struct fsl_ssi_private *ssi_private, bool enable)
{
+ /*
+ * Why are we setting up SACCST everytime we are starting a
+ * playback?
+ * Some CODECs (like VT1613 CODEC on UDOO board) like to
+ * (sometimes) set extra bits in their SLOTREQ requests.
+ * When a bit is set in a SLOTREQ request then SSI sets the
+ * relevant bit in SACCST automatically (it is enough if a bit was
+ * set in a SLOTREQ just once, bits in SACCST are 'sticky').
+ * If an extra slot gets enabled that's a disaster for playback
+ * because some of normal left or right channel samples are
+ * redirected instead to this extra slot.
+ *
+ * A workaround implemented in fsl-asoc-card of setting an
+ * appropriate CODEC register so that slots 3 & 4 (the normal
+ * stereo playback slots) are used for S/PDIF seems to mostly fix
+ * this issue on the UDOO board but since this CODEC is so
+ * untrustworthy let's play safe here and make sure that no extra
+ * slots are enabled every time a playback is started.
+ */
+ if (enable && fsl_ssi_is_ac97(ssi_private))
+ fsl_ssi_tx_ac97_saccst_setup(ssi_private);
+
fsl_ssi_config(ssi_private, enable, &ssi_private->rxtx_reg_val.tx);
}
@@ -639,12 +685,6 @@ static void fsl_ssi_setup_ac97(struct fsl_ssi_private *ssi_private)
regmap_write(regs, CCSR_SSI_SACNT,
CCSR_SSI_SACNT_AC97EN | CCSR_SSI_SACNT_FV);
- /* no SACC{ST,EN,DIS} regs on imx21-class SSI */
- if (!ssi_private->soc->imx21regs) {
- regmap_write(regs, CCSR_SSI_SACCDIS, 0xff);
- regmap_write(regs, CCSR_SSI_SACCEN, 0x300);
- }
-
/*
* Enable SSI, Transmit and Receive. AC97 has to communicate with the
* codec before a stream is started.
--
2.14.1
From: "Paul E. McKenney" <[email protected]>
[ Upstream commit 2fe2582649aa2355f79acddb86bd4d6c5363eb63 ]
The rcutorture test suite occasionally provokes a splat due to invoking
rt_mutex_lock() which needs to boost the priority of a task currently
sitting on a runqueue that belongs to an offline CPU:
WARNING: CPU: 0 PID: 12 at /home/paulmck/public_git/linux-rcu/arch/x86/kernel/smp.c:128 native_smp_send_reschedule+0x37/0x40
Modules linked in:
CPU: 0 PID: 12 Comm: rcub/7 Not tainted 4.14.0-rc4+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
task: ffff9ed3de5f8cc0 task.stack: ffffbbf80012c000
RIP: 0010:native_smp_send_reschedule+0x37/0x40
RSP: 0018:ffffbbf80012fd10 EFLAGS: 00010082
RAX: 000000000000002f RBX: ffff9ed3dd9cb300 RCX: 0000000000000004
RDX: 0000000080000004 RSI: 0000000000000086 RDI: 00000000ffffffff
RBP: ffffbbf80012fd10 R08: 000000000009da7a R09: 0000000000007b9d
R10: 0000000000000001 R11: ffffffffbb57c2cd R12: 000000000000000d
R13: ffff9ed3de5f8cc0 R14: 0000000000000061 R15: ffff9ed3ded59200
FS: 0000000000000000(0000) GS:ffff9ed3dea00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000080686f0 CR3: 000000001b9e0000 CR4: 00000000000006f0
Call Trace:
resched_curr+0x61/0xd0
switched_to_rt+0x8f/0xa0
rt_mutex_setprio+0x25c/0x410
task_blocks_on_rt_mutex+0x1b3/0x1f0
rt_mutex_slowlock+0xa9/0x1e0
rt_mutex_lock+0x29/0x30
rcu_boost_kthread+0x127/0x3c0
kthread+0x104/0x140
? rcu_report_unblock_qs_rnp+0x90/0x90
? kthread_create_on_node+0x40/0x40
ret_from_fork+0x22/0x30
Code: f0 00 0f 92 c0 84 c0 74 14 48 8b 05 34 74 c5 00 be fd 00 00 00 ff 90 a0 00 00 00 5d c3 89 fe 48 c7 c7 a0 c6 fc b9 e8 d5 b5 06 00 <0f> ff 5d c3 0f 1f 44 00 00 8b 05 a2 d1 13 02 85 c0 75 38 55 48
But the target task's priority has already been adjusted, so the only
purpose of switched_to_rt() invoking resched_curr() is to wake up the
CPU running some task that needs to be preempted by the boosted task.
But the CPU is offline, which presumably means that the task must be
migrated to some other CPU, and that this other CPU will undertake any
needed preemption at the time of migration. Because the runqueue lock
is held when resched_curr() is invoked, we know that the boosted task
cannot go anywhere, so it is not necessary to invoke resched_curr()
in this particular case.
This commit therefore makes switched_to_rt() refrain from invoking
resched_curr() when the target CPU is offline.
Signed-off-by: Paul E. McKenney <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
kernel/sched/rt.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/kernel/sched/rt.c b/kernel/sched/rt.c
index f6d68ddfa2f3..c7b0d2e7a9aa 100644
--- a/kernel/sched/rt.c
+++ b/kernel/sched/rt.c
@@ -2206,7 +2206,7 @@ static void switched_to_rt(struct rq *rq, struct task_struct *p)
if (tsk_nr_cpus_allowed(p) > 1 && rq->rt.overloaded)
queue_push_tasks(rq);
#endif /* CONFIG_SMP */
- if (p->prio < rq->curr->prio)
+ if (p->prio < rq->curr->prio && cpu_online(cpu_of(rq)))
resched_curr(rq);
}
}
--
2.14.1
From: Yixun Lan <[email protected]>
[ Upstream commit 75eccf5ed83250c0aeaeeb76f7288254ac0a87b4 ]
According to the datasheet, in Meson-GXBB/GXL series,
The clock gate bit for SARADC is HHI_GCLK_MPEG2 bit[22],
while clock gate bit for SANA is HHI_GCLK_MPEG0 bit[10].
Test passed at gxl-s905x-p212 board.
The following published datasheets are wrong and should be updated
[1] GXBB v1.1.4
[2] GXL v0.3_20170314
Fixes: 738f66d3211d ("clk: gxbb: add AmLogic GXBB clk controller driver")
Tested-by: Xingyu Chen <[email protected]>
Signed-off-by: Yixun Lan <[email protected]>
Signed-off-by: Jerome Brunet <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/clk/meson/gxbb.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/clk/meson/gxbb.c b/drivers/clk/meson/gxbb.c
index 9d9af446bafc..37e05d6e010a 100644
--- a/drivers/clk/meson/gxbb.c
+++ b/drivers/clk/meson/gxbb.c
@@ -572,7 +572,7 @@ static MESON_GATE(gxbb_pl301, HHI_GCLK_MPEG0, 6);
static MESON_GATE(gxbb_periphs, HHI_GCLK_MPEG0, 7);
static MESON_GATE(gxbb_spicc, HHI_GCLK_MPEG0, 8);
static MESON_GATE(gxbb_i2c, HHI_GCLK_MPEG0, 9);
-static MESON_GATE(gxbb_sar_adc, HHI_GCLK_MPEG0, 10);
+static MESON_GATE(gxbb_sana, HHI_GCLK_MPEG0, 10);
static MESON_GATE(gxbb_smart_card, HHI_GCLK_MPEG0, 11);
static MESON_GATE(gxbb_rng0, HHI_GCLK_MPEG0, 12);
static MESON_GATE(gxbb_uart0, HHI_GCLK_MPEG0, 13);
@@ -623,7 +623,7 @@ static MESON_GATE(gxbb_usb0_ddr_bridge, HHI_GCLK_MPEG2, 9);
static MESON_GATE(gxbb_mmc_pclk, HHI_GCLK_MPEG2, 11);
static MESON_GATE(gxbb_dvin, HHI_GCLK_MPEG2, 12);
static MESON_GATE(gxbb_uart2, HHI_GCLK_MPEG2, 15);
-static MESON_GATE(gxbb_sana, HHI_GCLK_MPEG2, 22);
+static MESON_GATE(gxbb_sar_adc, HHI_GCLK_MPEG2, 22);
static MESON_GATE(gxbb_vpu_intr, HHI_GCLK_MPEG2, 25);
static MESON_GATE(gxbb_sec_ahb_ahb3_bridge, HHI_GCLK_MPEG2, 26);
static MESON_GATE(gxbb_clk81_a53, HHI_GCLK_MPEG2, 29);
--
2.14.1
From: Mohammed Shafi Shajakhan <[email protected]>
[ Upstream commit 62ca0690cd495bb7c1414cdf0cf790c2922a1d79 ]
In 'ath10k_ce_alloc_pipe' the compile time sanity check to
ensure that there is sufficient buffers in CE4 for HTT Tx
MSDU descriptors, but this did not take into account of the
case with 'peer flow control' enabled, fix this.
Cc: Michal Kazior <[email protected]>
Signed-off-by: Mohammed Shafi Shajakhan <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/ath/ath10k/ce.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/wireless/ath/ath10k/ce.c b/drivers/net/wireless/ath/ath10k/ce.c
index 0b4d79659884..041ef3be87b9 100644
--- a/drivers/net/wireless/ath/ath10k/ce.c
+++ b/drivers/net/wireless/ath/ath10k/ce.c
@@ -1059,7 +1059,7 @@ int ath10k_ce_alloc_pipe(struct ath10k *ar, int ce_id,
*/
BUILD_BUG_ON(2 * TARGET_NUM_MSDU_DESC >
(CE_HTT_H2T_MSG_SRC_NENTRIES - 1));
- BUILD_BUG_ON(2 * TARGET_10X_NUM_MSDU_DESC >
+ BUILD_BUG_ON(2 * TARGET_10_4_NUM_MSDU_DESC_PFC >
(CE_HTT_H2T_MSG_SRC_NENTRIES - 1));
BUILD_BUG_ON(2 * TARGET_TLV_NUM_MSDU_DESC >
(CE_HTT_H2T_MSG_SRC_NENTRIES - 1));
--
2.14.1
From: Jiri Kosina <[email protected]>
[ Upstream commit 9abd04af951e5734c9d5cfee9b49790844b734cf ]
ELO devices have one Button usage in GenDesk field, which makes hid-input map
it to BTN_LEFT; that confuses userspace, which then considers the device to be
a mouse/touchpad instead of touchscreen.
Fix that by unmapping BTN_LEFT and keeping only BTN_TOUCH in place.
Signed-off-by: Jiri Kosina <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/hid/hid-elo.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/hid/hid-elo.c b/drivers/hid/hid-elo.c
index 0cd4f7216239..5eea6fe0d7bd 100644
--- a/drivers/hid/hid-elo.c
+++ b/drivers/hid/hid-elo.c
@@ -42,6 +42,12 @@ static int elo_input_configured(struct hid_device *hdev,
{
struct input_dev *input = hidinput->input;
+ /*
+ * ELO devices have one Button usage in GenDesk field, which makes
+ * hid-input map it to BTN_LEFT; that confuses userspace, which then
+ * considers the device to be a mouse/touchpad instead of touchscreen.
+ */
+ clear_bit(BTN_LEFT, input->keybit);
set_bit(BTN_TOUCH, input->keybit);
set_bit(ABS_PRESSURE, input->absbit);
input_set_abs_params(input, ABS_PRESSURE, 0, 256, 0, 0);
--
2.14.1
From: Ville Syrjälä <[email protected]>
[ Upstream commit 593f4b19a094c4426bd1e1e3cbab87a48bd13c71 ]
HDMI 2.0 Appendix F suggest that we should keep sending the infoframe
when switching from 3D to 2D mode, even if the infoframe isn't strictly
necessary (ie. not needed to transmit the VIC or stereo information).
This is a workaround against some sinks that fail to realize that they
should switch from 3D to 2D mode when the source stop transmitting
the infoframe.
v2: Handle unpack() as well
Pull the length calculation into a helper
Cc: Shashank Sharma <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Thierry Reding <[email protected]>
Cc: Hans Verkuil <[email protected]>
Cc: [email protected]
Reviewed-by: Andrzej Hajda <[email protected]> #v1
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Shashank Sharma <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/video/hdmi.c | 51 +++++++++++++++++++++++++++++++--------------------
1 file changed, 31 insertions(+), 20 deletions(-)
diff --git a/drivers/video/hdmi.c b/drivers/video/hdmi.c
index 162689227a23..b73520aaf697 100644
--- a/drivers/video/hdmi.c
+++ b/drivers/video/hdmi.c
@@ -321,6 +321,17 @@ int hdmi_vendor_infoframe_init(struct hdmi_vendor_infoframe *frame)
}
EXPORT_SYMBOL(hdmi_vendor_infoframe_init);
+static int hdmi_vendor_infoframe_length(const struct hdmi_vendor_infoframe *frame)
+{
+ /* for side by side (half) we also need to provide 3D_Ext_Data */
+ if (frame->s3d_struct >= HDMI_3D_STRUCTURE_SIDE_BY_SIDE_HALF)
+ return 6;
+ else if (frame->vic != 0 || frame->s3d_struct != HDMI_3D_STRUCTURE_INVALID)
+ return 5;
+ else
+ return 4;
+}
+
/**
* hdmi_vendor_infoframe_pack() - write a HDMI vendor infoframe to binary buffer
* @frame: HDMI infoframe
@@ -341,19 +352,11 @@ ssize_t hdmi_vendor_infoframe_pack(struct hdmi_vendor_infoframe *frame,
u8 *ptr = buffer;
size_t length;
- /* empty info frame */
- if (frame->vic == 0 && frame->s3d_struct == HDMI_3D_STRUCTURE_INVALID)
- return -EINVAL;
-
/* only one of those can be supplied */
if (frame->vic != 0 && frame->s3d_struct != HDMI_3D_STRUCTURE_INVALID)
return -EINVAL;
- /* for side by side (half) we also need to provide 3D_Ext_Data */
- if (frame->s3d_struct >= HDMI_3D_STRUCTURE_SIDE_BY_SIDE_HALF)
- frame->length = 6;
- else
- frame->length = 5;
+ frame->length = hdmi_vendor_infoframe_length(frame);
length = HDMI_INFOFRAME_HEADER_SIZE + frame->length;
@@ -372,14 +375,16 @@ ssize_t hdmi_vendor_infoframe_pack(struct hdmi_vendor_infoframe *frame,
ptr[5] = 0x0c;
ptr[6] = 0x00;
- if (frame->vic) {
- ptr[7] = 0x1 << 5; /* video format */
- ptr[8] = frame->vic;
- } else {
+ if (frame->s3d_struct != HDMI_3D_STRUCTURE_INVALID) {
ptr[7] = 0x2 << 5; /* video format */
ptr[8] = (frame->s3d_struct & 0xf) << 4;
if (frame->s3d_struct >= HDMI_3D_STRUCTURE_SIDE_BY_SIDE_HALF)
ptr[9] = (frame->s3d_ext_data & 0xf) << 4;
+ } else if (frame->vic) {
+ ptr[7] = 0x1 << 5; /* video format */
+ ptr[8] = frame->vic;
+ } else {
+ ptr[7] = 0x0 << 5; /* video format */
}
hdmi_infoframe_set_checksum(buffer, length);
@@ -1161,7 +1166,7 @@ hdmi_vendor_any_infoframe_unpack(union hdmi_vendor_any_infoframe *frame,
if (ptr[0] != HDMI_INFOFRAME_TYPE_VENDOR ||
ptr[1] != 1 ||
- (ptr[2] != 5 && ptr[2] != 6))
+ (ptr[2] != 4 && ptr[2] != 5 && ptr[2] != 6))
return -EINVAL;
length = ptr[2];
@@ -1189,16 +1194,22 @@ hdmi_vendor_any_infoframe_unpack(union hdmi_vendor_any_infoframe *frame,
hvf->length = length;
- if (hdmi_video_format == 0x1) {
- hvf->vic = ptr[4];
- } else if (hdmi_video_format == 0x2) {
+ if (hdmi_video_format == 0x2) {
+ if (length != 5 && length != 6)
+ return -EINVAL;
hvf->s3d_struct = ptr[4] >> 4;
if (hvf->s3d_struct >= HDMI_3D_STRUCTURE_SIDE_BY_SIDE_HALF) {
- if (length == 6)
- hvf->s3d_ext_data = ptr[5] >> 4;
- else
+ if (length != 6)
return -EINVAL;
+ hvf->s3d_ext_data = ptr[5] >> 4;
}
+ } else if (hdmi_video_format == 0x1) {
+ if (length != 5)
+ return -EINVAL;
+ hvf->vic = ptr[4];
+ } else {
+ if (length != 4)
+ return -EINVAL;
}
return 0;
--
2.14.1
From: Emmanuel Grumbach <[email protected]>
[ Upstream commit 992172e3aec19e5b0ea5b757ba40a146b9282d1e ]
When we are in a search cycle, we try different combinations
of parameters. Those combinations are called 'columns'.
When we switch to a new column, we first need to check if
this column has a suitable rate, if not, we can't try it.
This means we must not erase the statistics we gathered
for the previous column until we are sure that we are
indeed switching column.
The code that tries to switch to a new column first sets
a whole bunch of things for the new column, and only then
checks that we can find suitable rates in that column.
While doing that, the code mistakenly erased the rate
statistics. This code was right until
struct iwl_scale_tbl_info grew up for TPC.
Fix this to make sure we don't erase the rate statistics
until we are sure that we can indeed switch to the new
column.
Note that this bug is really harmless since it causes a
change in the behavior only when we can't find any rate
in the new column which should really not happen. In the
case we do find a suitable we reset the rate statistics
a few lines later anyway.
Signed-off-by: Emmanuel Grumbach <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/intel/iwlwifi/mvm/rs.c | 4 +---
1 file changed, 1 insertion(+), 3 deletions(-)
diff --git a/drivers/net/wireless/intel/iwlwifi/mvm/rs.c b/drivers/net/wireless/intel/iwlwifi/mvm/rs.c
index 227c5ed9cbe6..0aea476ebf50 100644
--- a/drivers/net/wireless/intel/iwlwifi/mvm/rs.c
+++ b/drivers/net/wireless/intel/iwlwifi/mvm/rs.c
@@ -1867,12 +1867,10 @@ static int rs_switch_to_column(struct iwl_mvm *mvm,
struct rs_rate *rate = &search_tbl->rate;
const struct rs_tx_column *column = &rs_tx_columns[col_id];
const struct rs_tx_column *curr_column = &rs_tx_columns[tbl->column];
- u32 sz = (sizeof(struct iwl_scale_tbl_info) -
- (sizeof(struct iwl_rate_scale_data) * IWL_RATE_COUNT));
unsigned long rate_mask = 0;
u32 rate_idx = 0;
- memcpy(search_tbl, tbl, sz);
+ memcpy(search_tbl, tbl, offsetof(struct iwl_scale_tbl_info, win));
rate->sgi = column->sgi;
rate->ant = column->ant;
--
2.14.1
From: Simon Shields <[email protected]>
[ Upstream commit 1b377924841df1e13ab5b225be3a83f807a92b52 ]
Trats2 uses gpf2-1 as the panel reset GPIO. gpy4-5 was only used
on early revisions of the board.
Fixes: 420ae8451a22 ("ARM: dts: exynos4412-trats2: add panel node")
Signed-off-by: Simon Shields <[email protected]>
Acked-by: Marek Szyprowski <[email protected]>
Tested-by: Marek Szyprowski <[email protected]>
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/exynos4412-trats2.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts
index 41ecd6d465a7..75a60633efff 100644
--- a/arch/arm/boot/dts/exynos4412-trats2.dts
+++ b/arch/arm/boot/dts/exynos4412-trats2.dts
@@ -408,7 +408,7 @@
reg = <0>;
vdd3-supply = <&lcd_vdd3_reg>;
vci-supply = <&ldo25_reg>;
- reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpf2 1 GPIO_ACTIVE_HIGH>;
power-on-delay= <50>;
reset-delay = <100>;
init-delay = <100>;
--
2.14.1
From: Johannes Berg <[email protected]>
[ Upstream commit 1d5e9f80ab021e3e1f9436627a4ad07a143ccb2c ]
When channel contexts are used, there's no global power level
(the power_level is always 0). Use the per-interface TX power
in mac80211_hwsim to have a proper setting for both cases.
This fixes the bgscan_simple and bgscan_learn test cases when
the number of channels advertised by hwsim is >1 by default.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/mac80211_hwsim.c | 9 +++------
1 file changed, 3 insertions(+), 6 deletions(-)
diff --git a/drivers/net/wireless/mac80211_hwsim.c b/drivers/net/wireless/mac80211_hwsim.c
index 4b462dc21c41..990c857992f6 100644
--- a/drivers/net/wireless/mac80211_hwsim.c
+++ b/drivers/net/wireless/mac80211_hwsim.c
@@ -552,8 +552,6 @@ struct mac80211_hwsim_data {
/* wmediumd portid responsible for netgroup of this radio */
u32 wmediumd;
- int power_level;
-
/* difference between this hw's clock and the real clock, in usecs */
s64 tsf_offset;
s64 bcn_delta;
@@ -1208,7 +1206,9 @@ static bool mac80211_hwsim_tx_frame_no_nl(struct ieee80211_hw *hw,
if (info->control.rates[0].flags & IEEE80211_TX_RC_SHORT_GI)
rx_status.flag |= RX_FLAG_SHORT_GI;
/* TODO: simulate real signal strength (and optional packet loss) */
- rx_status.signal = data->power_level - 50;
+ rx_status.signal = -50;
+ if (info->control.vif)
+ rx_status.signal += info->control.vif->bss_conf.txpower;
if (data->ps != PS_DISABLED)
hdr->frame_control |= cpu_to_le16(IEEE80211_FCTL_PM);
@@ -1607,7 +1607,6 @@ static int mac80211_hwsim_config(struct ieee80211_hw *hw, u32 changed)
WARN_ON(data->channel && data->use_chanctx);
- data->power_level = conf->power_level;
if (!data->started || !data->beacon_int)
tasklet_hrtimer_cancel(&data->beacon_timer);
else if (!hrtimer_is_queued(&data->beacon_timer.timer)) {
@@ -2212,7 +2211,6 @@ static const char mac80211_hwsim_gstrings_stats[][ETH_GSTRING_LEN] = {
"d_tx_failed",
"d_ps_mode",
"d_group",
- "d_tx_power",
};
#define MAC80211_HWSIM_SSTATS_LEN ARRAY_SIZE(mac80211_hwsim_gstrings_stats)
@@ -2249,7 +2247,6 @@ static void mac80211_hwsim_get_et_stats(struct ieee80211_hw *hw,
data[i++] = ar->tx_failed;
data[i++] = ar->ps;
data[i++] = ar->group;
- data[i++] = ar->power_level;
WARN_ON(i != MAC80211_HWSIM_SSTATS_LEN);
}
--
2.14.1
From: Hamad Kadmany <[email protected]>
[ Upstream commit b819447dfc4bd120c9d6cd8521252d544fce8fe7 ]
Existing code that ignores connection events during
reset flow will never take effect since it locks the
same mutex taken by the reset flow.
In addition, in case of unsolicited disconnect events ignore
those as well since device is about to get reset.
Signed-off-by: Hamad Kadmany <[email protected]>
Signed-off-by: Maya Erez <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/ath/wil6210/wmi.c | 11 +++++++++--
1 file changed, 9 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/ath/wil6210/wmi.c b/drivers/net/wireless/ath/wil6210/wmi.c
index fae4f1285d08..94a356bbb6b9 100644
--- a/drivers/net/wireless/ath/wil6210/wmi.c
+++ b/drivers/net/wireless/ath/wil6210/wmi.c
@@ -501,16 +501,16 @@ static void wmi_evt_connect(struct wil6210_priv *wil, int id, void *d, int len)
assoc_resp_ielen = 0;
}
- mutex_lock(&wil->mutex);
if (test_bit(wil_status_resetting, wil->status) ||
!test_bit(wil_status_fwready, wil->status)) {
wil_err(wil, "status_resetting, cancel connect event, CID %d\n",
evt->cid);
- mutex_unlock(&wil->mutex);
/* no need for cleanup, wil_reset will do that */
return;
}
+ mutex_lock(&wil->mutex);
+
if ((wdev->iftype == NL80211_IFTYPE_STATION) ||
(wdev->iftype == NL80211_IFTYPE_P2P_CLIENT)) {
if (!test_bit(wil_status_fwconnecting, wil->status)) {
@@ -608,6 +608,13 @@ static void wmi_evt_disconnect(struct wil6210_priv *wil, int id,
wil->sinfo_gen++;
+ if (test_bit(wil_status_resetting, wil->status) ||
+ !test_bit(wil_status_fwready, wil->status)) {
+ wil_err(wil, "status_resetting, cancel disconnect event\n");
+ /* no need for cleanup, wil_reset will do that */
+ return;
+ }
+
mutex_lock(&wil->mutex);
wil6210_disconnect(wil, evt->bssid, reason_code, true);
mutex_unlock(&wil->mutex);
--
2.14.1
From: Hannes Reinecke <[email protected]>
[ Upstream commit 97d27b0dd015e980ade63fda111fd1353276e28b ]
sg_remove_sfp_usercontext() is clearing any sg requests, but needs to
take 'rq_list_lock' when modifying the list.
Reported-by: Christoph Hellwig <[email protected]>
Signed-off-by: Hannes Reinecke <[email protected]>
Reviewed-by: Johannes Thumshirn <[email protected]>
Tested-by: Johannes Thumshirn <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/scsi/sg.c | 12 ++++++++++--
1 file changed, 10 insertions(+), 2 deletions(-)
diff --git a/drivers/scsi/sg.c b/drivers/scsi/sg.c
index 6b6064dc3467..e6333cae8550 100644
--- a/drivers/scsi/sg.c
+++ b/drivers/scsi/sg.c
@@ -524,6 +524,7 @@ sg_read(struct file *filp, char __user *buf, size_t count, loff_t * ppos)
} else
count = (old_hdr->result == 0) ? 0 : -EIO;
sg_finish_rem_req(srp);
+ sg_remove_request(sfp, srp);
retval = count;
free_old_hdr:
kfree(old_hdr);
@@ -564,6 +565,7 @@ sg_new_read(Sg_fd * sfp, char __user *buf, size_t count, Sg_request * srp)
}
err_out:
err2 = sg_finish_rem_req(srp);
+ sg_remove_request(sfp, srp);
return err ? : err2 ? : count;
}
@@ -800,6 +802,7 @@ sg_common_write(Sg_fd * sfp, Sg_request * srp,
SCSI_LOG_TIMEOUT(1, sg_printk(KERN_INFO, sfp->parentdp,
"sg_common_write: start_req err=%d\n", k));
sg_finish_rem_req(srp);
+ sg_remove_request(sfp, srp);
return k; /* probably out of space --> ENOMEM */
}
if (atomic_read(&sdp->detaching)) {
@@ -812,6 +815,7 @@ sg_common_write(Sg_fd * sfp, Sg_request * srp,
}
sg_finish_rem_req(srp);
+ sg_remove_request(sfp, srp);
return -ENODEV;
}
@@ -1302,6 +1306,7 @@ sg_rq_end_io_usercontext(struct work_struct *work)
struct sg_fd *sfp = srp->parentfp;
sg_finish_rem_req(srp);
+ sg_remove_request(sfp, srp);
kref_put(&sfp->f_ref, sg_remove_sfp);
}
@@ -1846,8 +1851,6 @@ sg_finish_rem_req(Sg_request *srp)
else
sg_remove_scat(sfp, req_schp);
- sg_remove_request(sfp, srp);
-
return ret;
}
@@ -2194,12 +2197,17 @@ sg_remove_sfp_usercontext(struct work_struct *work)
struct sg_fd *sfp = container_of(work, struct sg_fd, ew.work);
struct sg_device *sdp = sfp->parentdp;
Sg_request *srp;
+ unsigned long iflags;
/* Cleanup any responses which were never read(). */
+ write_lock_irqsave(&sfp->rq_list_lock, iflags);
while (!list_empty(&sfp->rq_list)) {
srp = list_first_entry(&sfp->rq_list, Sg_request, entry);
sg_finish_rem_req(srp);
+ list_del(&srp->entry);
+ srp->parentfp = NULL;
}
+ write_unlock_irqrestore(&sfp->rq_list_lock, iflags);
if (sfp->reserve.bufflen > 0) {
SCSI_LOG_TIMEOUT(6, sg_printk(KERN_INFO, sdp,
--
2.14.1
From: "Subhransu S. Prusty" <[email protected]>
[ Upstream commit 12ee4022f67f8854061b46e5c0a7ad6258ab66c2 ]
Geminilake is Skylake family platform. So add it's id to skl_plus check.
Fixes: 126cfa2f5e15 ("ALSA: hda: Add Geminilake HDMI codec ID")
Signed-off-by: Subhransu S. Prusty <[email protected]>
Cc: Senthilnathan Veppur <[email protected]>
Cc: Vinod Koul <[email protected]>
Cc: Takashi Iwai <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
sound/pci/hda/hda_intel.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c
index 293f3f213776..c9b2dff38c3c 100644
--- a/sound/pci/hda/hda_intel.c
+++ b/sound/pci/hda/hda_intel.c
@@ -369,8 +369,10 @@ enum {
#define IS_KBL_LP(pci) ((pci)->vendor == 0x8086 && (pci)->device == 0x9d71)
#define IS_KBL_H(pci) ((pci)->vendor == 0x8086 && (pci)->device == 0xa2f0)
#define IS_BXT(pci) ((pci)->vendor == 0x8086 && (pci)->device == 0x5a98)
+#define IS_GLK(pci) ((pci)->vendor == 0x8086 && (pci)->device == 0x3198)
#define IS_SKL_PLUS(pci) (IS_SKL(pci) || IS_SKL_LP(pci) || IS_BXT(pci)) || \
- IS_KBL(pci) || IS_KBL_LP(pci) || IS_KBL_H(pci)
+ IS_KBL(pci) || IS_KBL_LP(pci) || IS_KBL_H(pci) || \
+ IS_GLK(pci)
static char *driver_short_names[] = {
[AZX_DRIVER_ICH] = "HDA Intel",
--
2.14.1
From: Michael Scott <[email protected]>
[ Upstream commit d2891c4d071d807f01cc911dc42a68f4568d65cf ]
When adding 6lowpan devices very rapidly we sometimes see a crash:
[23122.306615] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.9.0-43-arm64 #1 Debian 4.9.9.linaro.43-1
[23122.315400] Hardware name: HiKey Development Board (DT)
[23122.320623] task: ffff800075443080 task.stack: ffff800075484000
[23122.326551] PC is at expire_timers+0x70/0x150
[23122.330907] LR is at run_timer_softirq+0xa0/0x1a0
[23122.335616] pc : [<ffff000008142dd8>] lr : [<ffff000008142f58>] pstate: 600001c5
This was due to add_peer_chan() unconditionally initializing the
lowpan_btle_dev->notify_peers delayed work structure, even if the
lowpan_btle_dev passed into add_peer_chan() had previously been
initialized.
Normally, this would go unnoticed as the delayed work timer is set for
100 msec, however when calling add_peer_chan() faster than 100 msec it
clears out a previously queued delay work causing the crash above.
To fix this, let add_peer_chan() know when a new lowpan_btle_dev is passed
in so that it only performs the delay work initialization when needed.
Signed-off-by: Michael Scott <[email protected]>
Acked-by: Jukka Rissanen <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
net/bluetooth/6lowpan.c | 10 +++++++---
1 file changed, 7 insertions(+), 3 deletions(-)
diff --git a/net/bluetooth/6lowpan.c b/net/bluetooth/6lowpan.c
index 1904a93f47d5..de7b82ece499 100644
--- a/net/bluetooth/6lowpan.c
+++ b/net/bluetooth/6lowpan.c
@@ -755,7 +755,8 @@ static void set_ip_addr_bits(u8 addr_type, u8 *addr)
}
static struct l2cap_chan *add_peer_chan(struct l2cap_chan *chan,
- struct lowpan_btle_dev *dev)
+ struct lowpan_btle_dev *dev,
+ bool new_netdev)
{
struct lowpan_peer *peer;
@@ -786,7 +787,8 @@ static struct l2cap_chan *add_peer_chan(struct l2cap_chan *chan,
spin_unlock(&devices_lock);
/* Notifying peers about us needs to be done without locks held */
- INIT_DELAYED_WORK(&dev->notify_peers, do_notify_peers);
+ if (new_netdev)
+ INIT_DELAYED_WORK(&dev->notify_peers, do_notify_peers);
schedule_delayed_work(&dev->notify_peers, msecs_to_jiffies(100));
return peer->chan;
@@ -843,6 +845,7 @@ out:
static inline void chan_ready_cb(struct l2cap_chan *chan)
{
struct lowpan_btle_dev *dev;
+ bool new_netdev = false;
dev = lookup_dev(chan->conn);
@@ -853,12 +856,13 @@ static inline void chan_ready_cb(struct l2cap_chan *chan)
l2cap_chan_del(chan, -ENOENT);
return;
}
+ new_netdev = true;
}
if (!try_module_get(THIS_MODULE))
return;
- add_peer_chan(chan, dev);
+ add_peer_chan(chan, dev, new_netdev);
ifup(dev->netdev);
}
--
2.14.1
From: Masami Hiramatsu <[email protected]>
[ Upstream commit d0381c81c2f782fa2131178d11e0cfb23d50d631 ]
Set the pages which is used for kprobes' singlestep buffer
and optprobe's trampoline instruction buffer to readonly.
This can prevent unexpected (or unintended) instruction
modification.
This also passes rodata_test as below.
Without this patch, rodata_test shows a warning:
WARNING: CPU: 0 PID: 1 at arch/x86/mm/dump_pagetables.c:235 note_page+0x7a9/0xa20
x86/mm: Found insecure W+X mapping at address ffffffffa0000000/0xffffffffa0000000
With this fix, no W+X pages are found:
x86/mm: Checked W+X mappings: passed, no W+X pages found.
rodata_test: all tests were successful
Reported-by: Andrey Ryabinin <[email protected]>
Signed-off-by: Masami Hiramatsu <[email protected]>
Cc: Ananth N Mavinakayanahalli <[email protected]>
Cc: Anil S Keshavamurthy <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Brian Gerst <[email protected]>
Cc: David S . Miller <[email protected]>
Cc: Denys Vlasenko <[email protected]>
Cc: H. Peter Anvin <[email protected]>
Cc: Josh Poimboeuf <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Ye Xiaolong <[email protected]>
Link: http://lkml.kernel.org/r/149076375592.22469.14174394514338612247.stgit@devbox
Signed-off-by: Ingo Molnar <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/x86/kernel/kprobes/core.c | 4 ++++
arch/x86/kernel/kprobes/opt.c | 3 +++
2 files changed, 7 insertions(+)
diff --git a/arch/x86/kernel/kprobes/core.c b/arch/x86/kernel/kprobes/core.c
index 808ee7f566f8..b8d3f1b60331 100644
--- a/arch/x86/kernel/kprobes/core.c
+++ b/arch/x86/kernel/kprobes/core.c
@@ -409,6 +409,8 @@ static int arch_copy_kprobe(struct kprobe *p)
{
int ret;
+ set_memory_rw((unsigned long)p->ainsn.insn & PAGE_MASK, 1);
+
/* Copy an instruction with recovering if other optprobe modifies it.*/
ret = __copy_instruction(p->ainsn.insn, p->addr);
if (!ret)
@@ -423,6 +425,8 @@ static int arch_copy_kprobe(struct kprobe *p)
else
p->ainsn.boostable = -1;
+ set_memory_ro((unsigned long)p->ainsn.insn & PAGE_MASK, 1);
+
/* Check whether the instruction modifies Interrupt Flag or not */
p->ainsn.if_modifier = is_IF_modifier(p->ainsn.insn);
diff --git a/arch/x86/kernel/kprobes/opt.c b/arch/x86/kernel/kprobes/opt.c
index dc20da1c78f0..fa671b90c374 100644
--- a/arch/x86/kernel/kprobes/opt.c
+++ b/arch/x86/kernel/kprobes/opt.c
@@ -371,6 +371,7 @@ int arch_prepare_optimized_kprobe(struct optimized_kprobe *op,
}
buf = (u8 *)op->optinsn.insn;
+ set_memory_rw((unsigned long)buf & PAGE_MASK, 1);
/* Copy instructions into the out-of-line buffer */
ret = copy_optimized_instructions(buf + TMPL_END_IDX, op->kp.addr);
@@ -393,6 +394,8 @@ int arch_prepare_optimized_kprobe(struct optimized_kprobe *op,
synthesize_reljump(buf + TMPL_END_IDX + op->optinsn.size,
(u8 *)op->kp.addr + op->optinsn.size);
+ set_memory_ro((unsigned long)buf & PAGE_MASK, 1);
+
flush_icache_range((unsigned long) buf,
(unsigned long) buf + TMPL_END_IDX +
op->optinsn.size + RELATIVEJUMP_SIZE);
--
2.14.1
From: Jani Nikula <[email protected]>
[ Upstream commit 1d1c36650752b7fb81cee515a9bba4131cac4b7c ]
Since drm_edid_to_eld() knows the connector type, we can set the type in
ELD while at it. Most connectors this gets called on are not DP
encoders, and with the HDMI type being 0, this does not change behaviour
for non-DP.
For i915 having this in place earlier would have saved a considerable
amount of debugging that lead to the fix 2d8f63297b9f ("drm/i915: always
update ELD connector type after get modes"). I don't see other drivers,
even the ones calling drm_edid_to_eld() on DP connectors, setting the
connector type in ELD.
Cc: Alex Deucher <[email protected]>
Cc: Christian König <[email protected]>
Cc: Archit Taneja <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Russell King <[email protected]>
Cc: CK Hu <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Ben Skeggs <[email protected]>
Cc: Mark Yao <[email protected]>
Cc: Benjamin Gaignard <[email protected]>
Cc: Vincent Abriou <[email protected]>
Cc: Thierry Reding <[email protected]>
Cc: Eric Anholt <[email protected]>
Reviewed-by: Ville Syrjälä <[email protected]>
Reviewed-by: Alex Deucher <[email protected]>
Acked-by: Thierry Reding <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/d527b31619528c477c2c136f25cdf118bc0cfc1d.1509545641.git.jani.nikula@intel.com
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/gpu/drm/drm_edid.c | 9 +++++++--
1 file changed, 7 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/drm_edid.c b/drivers/gpu/drm/drm_edid.c
index c6b281aa762f..6b31e0474271 100644
--- a/drivers/gpu/drm/drm_edid.c
+++ b/drivers/gpu/drm/drm_edid.c
@@ -3347,8 +3347,7 @@ EXPORT_SYMBOL(drm_edid_get_monitor_name);
* @edid: EDID to parse
*
* Fill the ELD (EDID-Like Data) buffer for passing to the audio driver. The
- * Conn_Type, HDCP and Port_ID ELD fields are left for the graphics driver to
- * fill in.
+ * HDCP and Port_ID ELD fields are left for the graphics driver to fill in.
*/
void drm_edid_to_eld(struct drm_connector *connector, struct edid *edid)
{
@@ -3426,6 +3425,12 @@ void drm_edid_to_eld(struct drm_connector *connector, struct edid *edid)
}
eld[5] |= total_sad_count << 4;
+ if (connector->connector_type == DRM_MODE_CONNECTOR_DisplayPort ||
+ connector->connector_type == DRM_MODE_CONNECTOR_eDP)
+ eld[DRM_ELD_SAD_COUNT_CONN_TYPE] |= DRM_ELD_CONN_TYPE_DP;
+ else
+ eld[DRM_ELD_SAD_COUNT_CONN_TYPE] |= DRM_ELD_CONN_TYPE_HDMI;
+
eld[DRM_ELD_BASELINE_ELD_LEN] =
DIV_ROUND_UP(drm_eld_calc_baseline_block_size(eld), 4);
--
2.14.1
From: Dean Jenkins <[email protected]>
[ Upstream commit 27bfbc21a0c0f711fa5382de026c7c0700c9ea28 ]
There is a race condition between a thread calling bt_accept_dequeue()
and a different thread calling bt_accept_unlink(). Protection against
concurrency is implemented using sk locking. However, sk locking causes
serialisation of the bt_accept_dequeue() and bt_accept_unlink() threads.
This serialisation can cause bt_accept_dequeue() to obtain the sk from the
parent list but becomes blocked waiting for the sk lock held by the
bt_accept_unlink() thread. bt_accept_unlink() unlinks sk and this thread
releases the sk lock unblocking bt_accept_dequeue() which potentially runs
bt_accept_unlink() again on the same sk causing a crash. The attempt to
double unlink the same sk from the parent list can cause a NULL pointer
dereference crash due to bt_sk(sk)->parent becoming NULL on the first
unlink, followed by the second unlink trying to execute
bt_sk(sk)->parent->sk_ack_backlog-- in bt_accept_unlink() which crashes.
When sk is in the parent list, bt_sk(sk)->parent will be not be NULL.
When sk is removed from the parent list, bt_sk(sk)->parent is set to
NULL. Therefore, add a defensive check for bt_sk(sk)->parent not being
NULL to ensure that sk is still in the parent list after the sk lock has
been taken in bt_accept_dequeue(). If bt_sk(sk)->parent is detected as
being NULL then restart the loop so that the loop variables are refreshed
to use the latest values. This is necessary as list_for_each_entry_safe()
is not thread safe so causing a risk of an infinite loop occurring as sk
could point to itself.
In addition, in bt_accept_dequeue() increase the sk reference count to
protect against early freeing of sk. Early freeing can be possible if the
bt_accept_unlink() thread calls l2cap_sock_kill() or rfcomm_sock_kill()
functions before bt_accept_dequeue() gets the sk lock.
For test purposes, the probability of failure can be increased by putting
a msleep of 1 second in bt_accept_dequeue() between getting the sk and
waiting for the sk lock. This exposes the fact that the loop
list_for_each_entry_safe(p, n, &bt_sk(parent)->accept_q) is not safe from
threads that unlink sk from the list in parallel with the loop which can
cause sk to become stale within the loop.
Signed-off-by: Dean Jenkins <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
net/bluetooth/af_bluetooth.c | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/net/bluetooth/af_bluetooth.c b/net/bluetooth/af_bluetooth.c
index 1aff2da9bc74..5d3698170004 100644
--- a/net/bluetooth/af_bluetooth.c
+++ b/net/bluetooth/af_bluetooth.c
@@ -163,6 +163,9 @@ void bt_accept_enqueue(struct sock *parent, struct sock *sk)
}
EXPORT_SYMBOL(bt_accept_enqueue);
+/* Calling function must hold the sk lock.
+ * bt_sk(sk)->parent must be non-NULL meaning sk is in the parent list.
+ */
void bt_accept_unlink(struct sock *sk)
{
BT_DBG("sk %p state %d", sk, sk->sk_state);
@@ -181,11 +184,32 @@ struct sock *bt_accept_dequeue(struct sock *parent, struct socket *newsock)
BT_DBG("parent %p", parent);
+restart:
list_for_each_entry_safe(s, n, &bt_sk(parent)->accept_q, accept_q) {
sk = (struct sock *)s;
+ /* Prevent early freeing of sk due to unlink and sock_kill */
+ sock_hold(sk);
lock_sock(sk);
+ /* Check sk has not already been unlinked via
+ * bt_accept_unlink() due to serialisation caused by sk locking
+ */
+ if (!bt_sk(sk)->parent) {
+ BT_DBG("sk %p, already unlinked", sk);
+ release_sock(sk);
+ sock_put(sk);
+
+ /* Restart the loop as sk is no longer in the list
+ * and also avoid a potential infinite loop because
+ * list_for_each_entry_safe() is not thread safe.
+ */
+ goto restart;
+ }
+
+ /* sk is safely in the parent list so reduce reference count */
+ sock_put(sk);
+
/* FIXME: Is this check still needed */
if (sk->sk_state == BT_CLOSED) {
bt_accept_unlink(sk);
--
2.14.1
From: Masami Hiramatsu <[email protected]>
[ Upstream commit bd0b90676c30fe640e7ead919b3e38846ac88ab7 ]
Fix the kprobe-booster not to boost far call instruction,
because a call may store the address in the single-step
execution buffer to the stack, which should be modified
after single stepping.
Currently, this instruction will be filtered as not
boostable in resume_execution(), so this is not a
critical issue.
Signed-off-by: Masami Hiramatsu <[email protected]>
Cc: Ananth N Mavinakayanahalli <[email protected]>
Cc: Andrey Ryabinin <[email protected]>
Cc: Anil S Keshavamurthy <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Brian Gerst <[email protected]>
Cc: David S . Miller <[email protected]>
Cc: Denys Vlasenko <[email protected]>
Cc: H. Peter Anvin <[email protected]>
Cc: Josh Poimboeuf <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Ye Xiaolong <[email protected]>
Link: http://lkml.kernel.org/r/149076340615.22469.14066273186134229909.stgit@devbox
Signed-off-by: Ingo Molnar <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/x86/kernel/kprobes/core.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/x86/kernel/kprobes/core.c b/arch/x86/kernel/kprobes/core.c
index b55d07b9d530..808ee7f566f8 100644
--- a/arch/x86/kernel/kprobes/core.c
+++ b/arch/x86/kernel/kprobes/core.c
@@ -199,6 +199,8 @@ retry:
return (opcode != 0x62 && opcode != 0x67);
case 0x70:
return 0; /* can't boost conditional jump */
+ case 0x90:
+ return opcode != 0x9a; /* can't boost call far */
case 0xc0:
/* can't boost software-interruptions */
return (0xc1 < opcode && opcode < 0xcc) || opcode == 0xcf;
--
2.14.1
From: Rajendra Nayak <[email protected]>
[ Upstream commit a62ca337b36e31621b582cbe8f17d9404a48e120 ]
Fix a typo which caused both vfe0 and vfe1 powerdomains to be
named as vfe0.
Signed-off-by: Rajendra Nayak <[email protected]>
Fixes: 7e824d507909 ("clk: qcom: gdsc: Add mmcc gdscs for msm8996 family")
Signed-off-by: Stephen Boyd <[email protected]>
Signed-off-by: Michael Turquette <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/clk/qcom/mmcc-msm8996.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/clk/qcom/mmcc-msm8996.c b/drivers/clk/qcom/mmcc-msm8996.c
index ca97e1151797..3b171bef913a 100644
--- a/drivers/clk/qcom/mmcc-msm8996.c
+++ b/drivers/clk/qcom/mmcc-msm8996.c
@@ -2984,7 +2984,7 @@ static struct gdsc vfe1_gdsc = {
.cxcs = (unsigned int []){ 0x36ac },
.cxc_count = 1,
.pd = {
- .name = "vfe0",
+ .name = "vfe1",
},
.parent = &camss_gdsc.pd,
.pwrsts = PWRSTS_OFF_ON,
--
2.14.1
From: Johannes Thumshirn <[email protected]>
[ Upstream commit 28676d869bbb5257b5f14c0c95ad3af3a7019dd5 ]
Check for a valid direction before starting the request, otherwise we
risk running into an assertion in the scsi midlayer checking for valid
requests.
[mkp: fixed typo]
Signed-off-by: Johannes Thumshirn <[email protected]>
Link: http://www.spinics.net/lists/linux-scsi/msg104400.html
Reported-by: Dmitry Vyukov <[email protected]>
Signed-off-by: Hannes Reinecke <[email protected]>
Tested-by: Johannes Thumshirn <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/scsi/sg.c | 46 ++++++++++++++++++++++++++++++++++------------
1 file changed, 34 insertions(+), 12 deletions(-)
diff --git a/drivers/scsi/sg.c b/drivers/scsi/sg.c
index cd9537ddc19f..6b6064dc3467 100644
--- a/drivers/scsi/sg.c
+++ b/drivers/scsi/sg.c
@@ -663,18 +663,14 @@ sg_write(struct file *filp, const char __user *buf, size_t count, loff_t * ppos)
* is a non-zero input_size, so emit a warning.
*/
if (hp->dxfer_direction == SG_DXFER_TO_FROM_DEV) {
- static char cmd[TASK_COMM_LEN];
- if (strcmp(current->comm, cmd)) {
- printk_ratelimited(KERN_WARNING
- "sg_write: data in/out %d/%d bytes "
- "for SCSI command 0x%x-- guessing "
- "data in;\n program %s not setting "
- "count and/or reply_len properly\n",
- old_hdr.reply_len - (int)SZ_SG_HEADER,
- input_size, (unsigned int) cmnd[0],
- current->comm);
- strcpy(cmd, current->comm);
- }
+ printk_ratelimited(KERN_WARNING
+ "sg_write: data in/out %d/%d bytes "
+ "for SCSI command 0x%x-- guessing "
+ "data in;\n program %s not setting "
+ "count and/or reply_len properly\n",
+ old_hdr.reply_len - (int)SZ_SG_HEADER,
+ input_size, (unsigned int) cmnd[0],
+ current->comm);
}
k = sg_common_write(sfp, srp, cmnd, sfp->timeout, blocking);
return (k < 0) ? k : count;
@@ -753,6 +749,29 @@ sg_new_write(Sg_fd *sfp, struct file *file, const char __user *buf,
return count;
}
+static bool sg_is_valid_dxfer(sg_io_hdr_t *hp)
+{
+ switch (hp->dxfer_direction) {
+ case SG_DXFER_NONE:
+ if (hp->dxferp || hp->dxfer_len > 0)
+ return false;
+ return true;
+ case SG_DXFER_TO_DEV:
+ case SG_DXFER_FROM_DEV:
+ case SG_DXFER_TO_FROM_DEV:
+ if (!hp->dxferp || hp->dxfer_len == 0)
+ return false;
+ return true;
+ case SG_DXFER_UNKNOWN:
+ if ((!hp->dxferp && hp->dxfer_len) ||
+ (hp->dxferp && hp->dxfer_len == 0))
+ return false;
+ return true;
+ default:
+ return false;
+ }
+}
+
static int
sg_common_write(Sg_fd * sfp, Sg_request * srp,
unsigned char *cmnd, int timeout, int blocking)
@@ -773,6 +792,9 @@ sg_common_write(Sg_fd * sfp, Sg_request * srp,
"sg_common_write: scsi opcode=0x%02x, cmd_size=%d\n",
(int) cmnd[0], (int) hp->cmd_len));
+ if (!sg_is_valid_dxfer(hp))
+ return -EINVAL;
+
k = sg_start_req(srp, cmnd);
if (k) {
SCSI_LOG_TIMEOUT(1, sg_printk(KERN_INFO, sfp->parentdp,
--
2.14.1
From: Laxman Dewangan <[email protected]>
[ Upstream commit 250b76f43f57d578ebff5e7211eb2c73aa5cd6ca ]
The rate of the PWM calculated as follows:
hz = NSEC_PER_SEC / period_ns;
rate = (rate + (hz / 2)) / hz;
This has the precision loss in lower PWM rate.
Change this to have more precision as:
hz = DIV_ROUND_CLOSEST_ULL(NSEC_PER_SEC * 100, period_ns);
rate = DIV_ROUND_CLOSEST(rate * 100, hz)
Example:
1. period_ns = 16672000, PWM clock rate is 200 KHz.
Based on old formula
hz = NSEC_PER_SEC / period_ns
= 1000000000ul/16672000
= 59 (59.98)
rate = (200K + 59/2)/59 = 3390
Based on new method:
hz = 5998
rate = DIV_ROUND_CLOSE(200000*100, 5998) = 3334
If we measure the PWM signal rate, we will get more accurate
period with rate value of 3334 instead of 3390.
2. period_ns = 16803898, PWM clock rate is 200 KHz.
Based on old formula:
hz = 59, rate = 3390
Based on new formula:
hz = 5951, rate = 3360
The PWM signal rate of 3360 is more near to requested period
than 3333.
Signed-off-by: Laxman Dewangan <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/pwm/pwm-tegra.c | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/drivers/pwm/pwm-tegra.c b/drivers/pwm/pwm-tegra.c
index e4647840cd6e..7e8906d6ab7a 100644
--- a/drivers/pwm/pwm-tegra.c
+++ b/drivers/pwm/pwm-tegra.c
@@ -76,6 +76,7 @@ static int tegra_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
struct tegra_pwm_chip *pc = to_tegra_pwm_chip(chip);
unsigned long long c = duty_ns;
unsigned long rate, hz;
+ unsigned long long ns100 = NSEC_PER_SEC;
u32 val = 0;
int err;
@@ -95,9 +96,11 @@ static int tegra_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
* cycles at the PWM clock rate will take period_ns nanoseconds.
*/
rate = clk_get_rate(pc->clk) >> PWM_DUTY_WIDTH;
- hz = NSEC_PER_SEC / period_ns;
- rate = (rate + (hz / 2)) / hz;
+ /* Consider precision in PWM_SCALE_WIDTH rate calculation */
+ ns100 *= 100;
+ hz = DIV_ROUND_CLOSEST_ULL(ns100, period_ns);
+ rate = DIV_ROUND_CLOSEST(rate * 100, hz);
/*
* Since the actual PWM divider is the register's frequency divider
--
2.14.1
From: Alexey Kardashevskiy <[email protected]>
[ Upstream commit 1282ba7fc28dbc66c3f0e4aaafaaa228361d1ae5 ]
The existing SPAPR TCE driver advertises both VFIO_SPAPR_TCE_IOMMU and
VFIO_SPAPR_TCE_v2_IOMMU types to the userspace and the userspace usually
picks the v2.
Normally the userspace would create a container, attach an IOMMU group
to it and only then set the IOMMU type (which would normally be v2).
However a specific IOMMU group may not support v2, in other words
it may not implement set_window/unset_window/take_ownership/
release_ownership and such a group should not be attached to
a v2 container.
This adds extra checks that a new group can do what the selected IOMMU
type suggests. The userspace can then test the return value from
ioctl(VFIO_SET_IOMMU, VFIO_SPAPR_TCE_v2_IOMMU) and try
VFIO_SPAPR_TCE_IOMMU.
Signed-off-by: Alexey Kardashevskiy <[email protected]>
Signed-off-by: Alex Williamson <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/vfio/vfio_iommu_spapr_tce.c | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/drivers/vfio/vfio_iommu_spapr_tce.c b/drivers/vfio/vfio_iommu_spapr_tce.c
index 59b3f62a2d64..87ad0d72d8a9 100644
--- a/drivers/vfio/vfio_iommu_spapr_tce.c
+++ b/drivers/vfio/vfio_iommu_spapr_tce.c
@@ -1332,8 +1332,16 @@ static int tce_iommu_attach_group(void *iommu_data,
if (!table_group->ops || !table_group->ops->take_ownership ||
!table_group->ops->release_ownership) {
+ if (container->v2) {
+ ret = -EPERM;
+ goto unlock_exit;
+ }
ret = tce_iommu_take_ownership(container, table_group);
} else {
+ if (!container->v2) {
+ ret = -EPERM;
+ goto unlock_exit;
+ }
ret = tce_iommu_take_ownership_ddw(container, table_group);
if (!tce_groups_attached(container) && !container->tables[0])
container->def_window_pending = true;
--
2.14.1
From: David Carrillo-Cisneros <[email protected]>
[ Upstream commit 0973ad97c187e06aece61f685b9c3b2d93290a73 ]
Session sets a number parameters that rely on evlist. These parameters
are not used in pipe-mode and should not be set, since evlist is
unavailable. Fix that.
Signed-off-by: David Carrillo-Cisneros <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Paul Turner <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Simon Que <[email protected]>
Cc: Stephane Eranian <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
[ Check if file != NULL in perf_session__new(), like when used by builtin-top.c ]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/perf/util/session.c | 16 +++++++++++++---
1 file changed, 13 insertions(+), 3 deletions(-)
diff --git a/tools/perf/util/session.c b/tools/perf/util/session.c
index 97b4822fe7f0..7e0573e55a35 100644
--- a/tools/perf/util/session.c
+++ b/tools/perf/util/session.c
@@ -139,8 +139,14 @@ struct perf_session *perf_session__new(struct perf_data_file *file,
if (perf_session__open(session) < 0)
goto out_close;
- perf_session__set_id_hdr_size(session);
- perf_session__set_comm_exec(session);
+ /*
+ * set session attributes that are present in perf.data
+ * but not in pipe-mode.
+ */
+ if (!file->is_pipe) {
+ perf_session__set_id_hdr_size(session);
+ perf_session__set_comm_exec(session);
+ }
}
} else {
session->machines.host.env = &perf_env;
@@ -155,7 +161,11 @@ struct perf_session *perf_session__new(struct perf_data_file *file,
pr_warning("Cannot read kernel map\n");
}
- if (tool && tool->ordering_requires_timestamps &&
+ /*
+ * In pipe-mode, evlist is empty until PERF_RECORD_HEADER_ATTR is
+ * processed, so perf_evlist__sample_id_all is not meaningful here.
+ */
+ if ((!file || !file->is_pipe) && tool && tool->ordering_requires_timestamps &&
tool->ordered_events && !perf_evlist__sample_id_all(session->evlist)) {
dump_printf("WARNING: No sample_id_all support, falling back to unordered processing\n");
tool->ordered_events = false;
--
2.14.1
From: Alexey Kardashevskiy <[email protected]>
[ Upstream commit 3393af24b665cb0aea7353b05e522b03ab1e7d73 ]
This adds missing checking for kzalloc() return value.
Fixes: 4b6fad7097f8 ("powerpc/mm/iommu, vfio/spapr: Put pages on VFIO container shutdown")
Signed-off-by: Alexey Kardashevskiy <[email protected]>
Reviewed-by: David Gibson <[email protected]>
Signed-off-by: Alex Williamson <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/vfio/vfio_iommu_spapr_tce.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/drivers/vfio/vfio_iommu_spapr_tce.c b/drivers/vfio/vfio_iommu_spapr_tce.c
index 87ad0d72d8a9..70c748a5fbcc 100644
--- a/drivers/vfio/vfio_iommu_spapr_tce.c
+++ b/drivers/vfio/vfio_iommu_spapr_tce.c
@@ -195,6 +195,11 @@ static long tce_iommu_register_pages(struct tce_container *container,
return ret;
tcemem = kzalloc(sizeof(*tcemem), GFP_KERNEL);
+ if (!tcemem) {
+ mm_iommu_put(container->mm, mem);
+ return -ENOMEM;
+ }
+
tcemem->mem = mem;
list_add(&tcemem->next, &container->prereg_list);
--
2.14.1
From: Fugang Duan <[email protected]>
[ Upstream commit 9269e5560b261eb9ee157497890dc0948db76cf8 ]
Many boards use i2c/spi expander gpio as phy-reset-gpios and these
gpios maybe registered after fec port, driver should check the return
value of .of_get_named_gpio().
Signed-off-by: Fugang Duan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/freescale/fec_main.c | 26 ++++++++++++++++++--------
1 file changed, 18 insertions(+), 8 deletions(-)
diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c
index 917091871259..dd6e07c748f5 100644
--- a/drivers/net/ethernet/freescale/fec_main.c
+++ b/drivers/net/ethernet/freescale/fec_main.c
@@ -3209,7 +3209,7 @@ static int fec_enet_init(struct net_device *ndev)
}
#ifdef CONFIG_OF
-static void fec_reset_phy(struct platform_device *pdev)
+static int fec_reset_phy(struct platform_device *pdev)
{
int err, phy_reset;
bool active_high = false;
@@ -3217,7 +3217,7 @@ static void fec_reset_phy(struct platform_device *pdev)
struct device_node *np = pdev->dev.of_node;
if (!np)
- return;
+ return 0;
of_property_read_u32(np, "phy-reset-duration", &msec);
/* A sane reset duration should not be longer than 1s */
@@ -3225,8 +3225,10 @@ static void fec_reset_phy(struct platform_device *pdev)
msec = 1;
phy_reset = of_get_named_gpio(np, "phy-reset-gpios", 0);
- if (!gpio_is_valid(phy_reset))
- return;
+ if (phy_reset == -EPROBE_DEFER)
+ return phy_reset;
+ else if (!gpio_is_valid(phy_reset))
+ return 0;
active_high = of_property_read_bool(np, "phy-reset-active-high");
@@ -3235,7 +3237,7 @@ static void fec_reset_phy(struct platform_device *pdev)
"phy-reset");
if (err) {
dev_err(&pdev->dev, "failed to get phy-reset-gpios: %d\n", err);
- return;
+ return err;
}
if (msec > 20)
@@ -3244,14 +3246,17 @@ static void fec_reset_phy(struct platform_device *pdev)
usleep_range(msec * 1000, msec * 1000 + 1000);
gpio_set_value_cansleep(phy_reset, !active_high);
+
+ return 0;
}
#else /* CONFIG_OF */
-static void fec_reset_phy(struct platform_device *pdev)
+static int fec_reset_phy(struct platform_device *pdev)
{
/*
* In case of platform probe, the reset has been done
* by machine code.
*/
+ return 0;
}
#endif /* CONFIG_OF */
@@ -3422,6 +3427,7 @@ fec_probe(struct platform_device *pdev)
if (ret) {
dev_err(&pdev->dev,
"Failed to enable phy regulator: %d\n", ret);
+ clk_disable_unprepare(fep->clk_ipg);
goto failed_regulator;
}
} else {
@@ -3434,7 +3440,9 @@ fec_probe(struct platform_device *pdev)
pm_runtime_set_active(&pdev->dev);
pm_runtime_enable(&pdev->dev);
- fec_reset_phy(pdev);
+ ret = fec_reset_phy(pdev);
+ if (ret)
+ goto failed_reset;
if (fep->bufdesc_ex)
fec_ptp_init(pdev);
@@ -3495,8 +3503,10 @@ failed_init:
fec_ptp_stop(pdev);
if (fep->reg_phy)
regulator_disable(fep->reg_phy);
+failed_reset:
+ pm_runtime_put(&pdev->dev);
+ pm_runtime_disable(&pdev->dev);
failed_regulator:
- clk_disable_unprepare(fep->clk_ipg);
failed_clk_ipg:
fec_enet_clk_enable(ndev, false);
failed_clk:
--
2.14.1
From: Mark Rutland <[email protected]>
[ Upstream commit 7654137071fa706e5c91f4f27bc2a5cd7e435a9b ]
In armpmu_dispatch_irq() we look at arm_pmu::plat_device to acquire
platdata, so that we can defer to platform-specific IRQ handling,
required on some 32-bit parts. With the advent of ACPI we won't always
have a platform_device, and so we must avoid trying to dereference
fields from it.
This patch fixes up armpmu_dispatch_irq() to avoid doing so, introducing
a new armpmu_get_platdata() helper.
Signed-off-by: Mark Rutland <[email protected]>
Tested-by: Jeremy Linton <[email protected]>
Cc: Will Deacon <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/perf/arm_pmu.c | 12 +++++++++---
1 file changed, 9 insertions(+), 3 deletions(-)
diff --git a/drivers/perf/arm_pmu.c b/drivers/perf/arm_pmu.c
index b37b57294566..af82edc7fa5c 100644
--- a/drivers/perf/arm_pmu.c
+++ b/drivers/perf/arm_pmu.c
@@ -322,10 +322,16 @@ validate_group(struct perf_event *event)
return 0;
}
+static struct arm_pmu_platdata *armpmu_get_platdata(struct arm_pmu *armpmu)
+{
+ struct platform_device *pdev = armpmu->plat_device;
+
+ return pdev ? dev_get_platdata(&pdev->dev) : NULL;
+}
+
static irqreturn_t armpmu_dispatch_irq(int irq, void *dev)
{
struct arm_pmu *armpmu;
- struct platform_device *plat_device;
struct arm_pmu_platdata *plat;
int ret;
u64 start_clock, finish_clock;
@@ -337,8 +343,8 @@ static irqreturn_t armpmu_dispatch_irq(int irq, void *dev)
* dereference.
*/
armpmu = *(void **)dev;
- plat_device = armpmu->plat_device;
- plat = dev_get_platdata(&plat_device->dev);
+
+ plat = armpmu_get_platdata(armpmu);
start_clock = sched_clock();
if (plat && plat->handle_irq)
--
2.14.1
From: David Carrillo-Cisneros <[email protected]>
[ Upstream commit 1e0d4f0200e4dbdfc38d818f329d8a0955f7c6f5 ]
__perf_session__process_pipe_events reuses the same memory buffer to
process all events in the pipe.
When reordering is needed (e.g. -b option), events are not immediately
flushed, but kept around until reordering is possible, causing
memory corruption.
The problem is usually observed by a "Unknown sample error" output. It
can easily be reproduced by:
perf record -o - noploop | perf inject -b > output
Committer testing:
Before:
$ perf record -o - stress -t 2 -c 2 | perf inject -b > /dev/null
stress: info: [8297] dispatching hogs: 2 cpu, 0 io, 0 vm, 0 hdd
stress: info: [8297] successful run completed in 2s
[ perf record: Woken up 3 times to write data ]
[ perf record: Captured and wrote 0.000 MB - ]
Warning:
Found 1 unknown events!
Is this an older tool processing a perf.data file generated by a more recent tool?
If that is not the case, consider reporting to [email protected].
$
After:
$ perf record -o - stress -t 2 -c 2 | perf inject -b > /dev/null
stress: info: [9027] dispatching hogs: 2 cpu, 0 io, 0 vm, 0 hdd
stress: info: [9027] successful run completed in 2s
[ perf record: Woken up 3 times to write data ]
[ perf record: Captured and wrote 0.000 MB - ]
no symbols found in /usr/bin/stress, maybe install a debug package?
no symbols found in /usr/bin/stress, maybe install a debug package?
$
Signed-off-by: David Carrillo-Cisneros <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Paul Turner <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Simon Que <[email protected]>
Cc: Stephane Eranian <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/perf/util/ordered-events.c | 3 ++-
tools/perf/util/session.c | 1 +
2 files changed, 3 insertions(+), 1 deletion(-)
diff --git a/tools/perf/util/ordered-events.c b/tools/perf/util/ordered-events.c
index fe84df1875aa..e70e935b1841 100644
--- a/tools/perf/util/ordered-events.c
+++ b/tools/perf/util/ordered-events.c
@@ -79,7 +79,7 @@ static union perf_event *dup_event(struct ordered_events *oe,
static void free_dup_event(struct ordered_events *oe, union perf_event *event)
{
- if (oe->copy_on_queue) {
+ if (event && oe->copy_on_queue) {
oe->cur_alloc_size -= event->header.size;
free(event);
}
@@ -150,6 +150,7 @@ void ordered_events__delete(struct ordered_events *oe, struct ordered_event *eve
list_move(&event->list, &oe->cache);
oe->nr_events--;
free_dup_event(oe, event->event);
+ event->event = NULL;
}
int ordered_events__queue(struct ordered_events *oe, union perf_event *event,
diff --git a/tools/perf/util/session.c b/tools/perf/util/session.c
index 5d61242a6e64..97b4822fe7f0 100644
--- a/tools/perf/util/session.c
+++ b/tools/perf/util/session.c
@@ -1628,6 +1628,7 @@ static int __perf_session__process_pipe_events(struct perf_session *session)
buf = malloc(cur_size);
if (!buf)
return -errno;
+ ordered_events__set_copy_on_queue(oe, true);
more:
event = buf;
err = readn(fd, event, sizeof(struct perf_event_header));
--
2.14.1
From: Uwe Kleine-König <[email protected]>
[ Upstream commit e61c38d85b7392e033ee03bca46f1d6006156175 ]
If the UART is operated in DTE mode and UCR3_DCD or UCR3_RI are 1 (which
is the reset default) and the opposite side pulls the respective line to
its active level the irq triggers after it is requested in .probe.
These irqs were already disabled in .startup but this might be too late.
Also setup of the UFCR_DCEDTE bit (currently done in .set_termios) is
done very late which is critical as it also controls direction of some
pins.
So setup UFCR_DCEDTE earlier (in .probe) and also disable the broken
irqs in DTE mode there before requesting irqs.
Acked-by: Lucas Stach <[email protected]>
Signed-off-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/tty/serial/imx.c | 36 +++++++++++++++++++++++-------------
1 file changed, 23 insertions(+), 13 deletions(-)
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 521a6e450755..f575a33974fa 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -1316,19 +1316,10 @@ static int imx_startup(struct uart_port *port)
if (!is_imx1_uart(sport)) {
temp = readl(sport->port.membase + UCR3);
- /*
- * The effect of RI and DCD differs depending on the UFCR_DCEDTE
- * bit. In DCE mode they control the outputs, in DTE mode they
- * enable the respective irqs. At least the DCD irq cannot be
- * cleared on i.MX25 at least, so it's not usable and must be
- * disabled. I don't have test hardware to check if RI has the
- * same problem but I consider this likely so it's disabled for
- * now, too.
- */
- temp |= IMX21_UCR3_RXDMUXSEL | UCR3_ADNIMP |
- UCR3_DTRDEN | UCR3_RI | UCR3_DCD;
+ temp |= UCR3_DTRDEN | UCR3_RI | UCR3_DCD;
if (sport->dte_mode)
+ /* disable broken interrupts */
temp &= ~(UCR3_RI | UCR3_DCD);
writel(temp, sport->port.membase + UCR3);
@@ -1583,8 +1574,6 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios,
ufcr = readl(sport->port.membase + UFCR);
ufcr = (ufcr & (~UFCR_RFDIV)) | UFCR_RFDIV_REG(div);
- if (sport->dte_mode)
- ufcr |= UFCR_DCEDTE;
writel(ufcr, sport->port.membase + UFCR);
writel(num, sport->port.membase + UBIR);
@@ -2149,6 +2138,27 @@ static int serial_imx_probe(struct platform_device *pdev)
UCR1_TXMPTYEN | UCR1_RTSDEN);
writel_relaxed(reg, sport->port.membase + UCR1);
+ if (!is_imx1_uart(sport) && sport->dte_mode) {
+ /*
+ * The DCEDTE bit changes the direction of DSR, DCD, DTR and RI
+ * and influences if UCR3_RI and UCR3_DCD changes the level of RI
+ * and DCD (when they are outputs) or enables the respective
+ * irqs. So set this bit early, i.e. before requesting irqs.
+ */
+ writel(UFCR_DCEDTE, sport->port.membase + UFCR);
+
+ /*
+ * Disable UCR3_RI and UCR3_DCD irqs. They are also not
+ * enabled later because they cannot be cleared
+ * (confirmed on i.MX25) which makes them unusable.
+ */
+ writel(IMX21_UCR3_RXDMUXSEL | UCR3_ADNIMP | UCR3_DSR,
+ sport->port.membase + UCR3);
+
+ } else {
+ writel(0, sport->port.membase + UFCR);
+ }
+
clk_disable_unprepare(sport->clk_ipg);
/*
--
2.14.1
From: Johannes Berg <[email protected]>
[ Upstream commit 5cddd05c9cbe420436799716d009bc0372ef8268 ]
When receiving a frame, we currently pull in sizeof(*hdr) plus
some extra (crypto/snap), which is too much, most headers aren't
actually sizeof(*hdr) since that takes into account the 4-address
format but doesn't take into account QoS. As a result, a typical
frame will have 4 bytes of the payload in the SKB header already.
Fix this by calculating the correct header length, and now that
we have that, align the end of the SKB header to a multiple of 4
so that the IP header will be aligned properly when pulled in.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/intel/iwlwifi/mvm/rx.c | 18 +++++++++++++++---
1 file changed, 15 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/intel/iwlwifi/mvm/rx.c b/drivers/net/wireless/intel/iwlwifi/mvm/rx.c
index 0e60e38b2acf..b78e60eb600f 100644
--- a/drivers/net/wireless/intel/iwlwifi/mvm/rx.c
+++ b/drivers/net/wireless/intel/iwlwifi/mvm/rx.c
@@ -104,7 +104,20 @@ static void iwl_mvm_pass_packet_to_mac80211(struct iwl_mvm *mvm,
u8 crypt_len,
struct iwl_rx_cmd_buffer *rxb)
{
- unsigned int hdrlen, fraglen;
+ unsigned int hdrlen = ieee80211_hdrlen(hdr->frame_control);
+ unsigned int fraglen;
+
+ /*
+ * The 'hdrlen' (plus the 8 bytes for the SNAP and the crypt_len,
+ * but those are all multiples of 4 long) all goes away, but we
+ * want the *end* of it, which is going to be the start of the IP
+ * header, to be aligned when it gets pulled in.
+ * The beginning of the skb->data is aligned on at least a 4-byte
+ * boundary after allocation. Everything here is aligned at least
+ * on a 2-byte boundary so we can just take hdrlen & 3 and pad by
+ * the result.
+ */
+ skb_reserve(skb, hdrlen & 3);
/* If frame is small enough to fit in skb->head, pull it completely.
* If not, only pull ieee80211_hdr (including crypto if present, and
@@ -118,8 +131,7 @@ static void iwl_mvm_pass_packet_to_mac80211(struct iwl_mvm *mvm,
* If the latter changes (there are efforts in the standards group
* to do so) we should revisit this and ieee80211_data_to_8023().
*/
- hdrlen = (len <= skb_tailroom(skb)) ? len :
- sizeof(*hdr) + crypt_len + 8;
+ hdrlen = (len <= skb_tailroom(skb)) ? len : hdrlen + crypt_len + 8;
memcpy(skb_put(skb, hdrlen), hdr, hdrlen);
fraglen = len - hdrlen;
--
2.14.1
From: Jin Yao <[email protected]>
[ Upstream commit 32ccb130f5325abc81b32b1a538390f46e4860f6 ]
The kernel has a special check for a specific irq_vectors trace event.
TRACE_EVENT_PERF_PERM(irq_work_exit,
is_sampling_event(p_event) ? -EPERM : 0);
The perf-record fails for this irq_vectors event when it is present,
like when using a wildcard:
root@skl:/tmp# perf record -a -e irq_vectors:* sleep 2
Error:
You may not have permission to collect system-wide stats.
Consider tweaking /proc/sys/kernel/perf_event_paranoid,
which controls use of the performance events system by
unprivileged users (without CAP_SYS_ADMIN).
The current value is 2:
-1: Allow use of (almost) all events by all users
>= 0: Disallow raw tracepoint access by users without CAP_IOC_LOCK
>= 1: Disallow CPU event access by users without CAP_SYS_ADMIN
>= 2: Disallow kernel profiling by users without CAP_SYS_ADMIN
To make this setting permanent, edit /etc/sysctl.conf too, e.g.:
kernel.perf_event_paranoid = -1
This patch prints out the exact sub event that failed with EPERM for
wildcards to help in understanding what went wrong when this event is
present:
After the patch:
root@skl:/tmp# perf record -a -e irq_vectors:* sleep 2
Error:
No permission to enable irq_vectors:irq_work_exit event.
You may not have permission to collect system-wide stats.
......
Committer notes:
So we have a lot of irq_vectors events:
[root@jouet ~]# perf list irq_vectors:*
List of pre-defined events (to be used in -e):
irq_vectors:call_function_entry [Tracepoint event]
irq_vectors:call_function_exit [Tracepoint event]
irq_vectors:call_function_single_entry [Tracepoint event]
irq_vectors:call_function_single_exit [Tracepoint event]
irq_vectors:deferred_error_apic_entry [Tracepoint event]
irq_vectors:deferred_error_apic_exit [Tracepoint event]
irq_vectors:error_apic_entry [Tracepoint event]
irq_vectors:error_apic_exit [Tracepoint event]
irq_vectors:irq_work_entry [Tracepoint event]
irq_vectors:irq_work_exit [Tracepoint event]
irq_vectors:local_timer_entry [Tracepoint event]
irq_vectors:local_timer_exit [Tracepoint event]
irq_vectors:reschedule_entry [Tracepoint event]
irq_vectors:reschedule_exit [Tracepoint event]
irq_vectors:spurious_apic_entry [Tracepoint event]
irq_vectors:spurious_apic_exit [Tracepoint event]
irq_vectors:thermal_apic_entry [Tracepoint event]
irq_vectors:thermal_apic_exit [Tracepoint event]
irq_vectors:threshold_apic_entry [Tracepoint event]
irq_vectors:threshold_apic_exit [Tracepoint event]
irq_vectors:x86_platform_ipi_entry [Tracepoint event]
irq_vectors:x86_platform_ipi_exit [Tracepoint event]
#
And some may be sampled:
[root@jouet ~]# perf record -e irq_vectors:local* sleep 20s
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.020 MB perf.data (2 samples) ]
[root@jouet ~]# perf report -D | egrep 'stats:|events:'
Aggregated stats:
TOTAL events: 155
MMAP events: 144
COMM events: 2
EXIT events: 1
SAMPLE events: 2
MMAP2 events: 4
FINISHED_ROUND events: 1
TIME_CONV events: 1
irq_vectors:local_timer_entry stats:
TOTAL events: 1
SAMPLE events: 1
irq_vectors:local_timer_exit stats:
TOTAL events: 1
SAMPLE events: 1
[root@jouet ~]#
But, as shown in the tracepoint definition at the start of this message,
some, like "irq_vectors:irq_work_exit", may not be sampled, just counted,
i.e. if we try to sample, as when using 'perf record', we get an error:
[root@jouet ~]# perf record -e irq_vectors:irq_work_exit
Error:
You may not have permission to collect system-wide stats.
Consider tweaking /proc/sys/kernel/perf_event_paranoid,
<SNIP>
The error message is misleading, this patch will help in pointing out
what is the event causing such an error, but the error message needs
improvement, i.e. we need to figure out a way to check if a tracepoint
is counting only, like this one, when all we can do is to count it with
'perf stat', at most printing the delta using interval printing, as in:
[root@jouet ~]# perf stat -I 5000 -e irq_vectors:irq_work_*
# time counts unit events
5.000168871 0 irq_vectors:irq_work_entry
5.000168871 0 irq_vectors:irq_work_exit
10.000676730 0 irq_vectors:irq_work_entry
10.000676730 0 irq_vectors:irq_work_exit
15.001122415 0 irq_vectors:irq_work_entry
15.001122415 0 irq_vectors:irq_work_exit
20.001298051 0 irq_vectors:irq_work_entry
20.001298051 0 irq_vectors:irq_work_exit
25.001485020 1 irq_vectors:irq_work_entry
25.001485020 1 irq_vectors:irq_work_exit
30.001658706 0 irq_vectors:irq_work_entry
30.001658706 0 irq_vectors:irq_work_exit
^C 32.045711878 0 irq_vectors:irq_work_entry
32.045711878 0 irq_vectors:irq_work_exit
[root@jouet ~]#
But at least, when we use a wildcard, this patch helps a bit.
Signed-off-by: Yao Jin <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Kan Liang <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/perf/util/evsel.c | 8 +++++++-
1 file changed, 7 insertions(+), 1 deletion(-)
diff --git a/tools/perf/util/evsel.c b/tools/perf/util/evsel.c
index 8bc271141d9d..539724c7d30b 100644
--- a/tools/perf/util/evsel.c
+++ b/tools/perf/util/evsel.c
@@ -2400,11 +2400,17 @@ int perf_evsel__open_strerror(struct perf_evsel *evsel, struct target *target,
int err, char *msg, size_t size)
{
char sbuf[STRERR_BUFSIZE];
+ int printed = 0;
switch (err) {
case EPERM:
case EACCES:
- return scnprintf(msg, size,
+ if (err == EPERM)
+ printed = scnprintf(msg, size,
+ "No permission to enable %s event.\n\n",
+ perf_evsel__name(evsel));
+
+ return scnprintf(msg + printed, size - printed,
"You may not have permission to collect %sstats.\n\n"
"Consider tweaking /proc/sys/kernel/perf_event_paranoid,\n"
"which controls use of the performance events system by\n"
--
2.14.1
From: Mike Leach <[email protected]>
[ Upstream commit eeedc5421dd3b51de73e6106405c5c77f920f281 ]
Corrected to get the port numbering to allow programmable replicator driver
to operate correctly.
By convention, CoreSight devices number ports, not endpoints in
the .dts files:-
port {
reg<N>
endpoint {
}
}
Existing code read endpoint number - always 0x0, rather than the correct
port number.
Signed-off-by: Mike Leach <[email protected]>
Signed-off-by: Mathieu Poirier <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/hwtracing/coresight/of_coresight.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/hwtracing/coresight/of_coresight.c b/drivers/hwtracing/coresight/of_coresight.c
index 629e031b7456..09142e99e915 100644
--- a/drivers/hwtracing/coresight/of_coresight.c
+++ b/drivers/hwtracing/coresight/of_coresight.c
@@ -149,7 +149,7 @@ struct coresight_platform_data *of_get_coresight_platform_data(
continue;
/* The local out port number */
- pdata->outports[i] = endpoint.id;
+ pdata->outports[i] = endpoint.port;
/*
* Get a handle on the remote port and parent
--
2.14.1
From: Yuyang Du <[email protected]>
[ Upstream commit 9f20dfb44d03745d0d3cef2ffb3abf8d8024fa61 ]
This fixes the commit: 1cd8fd2887e1 ("usb: gadget: dummy_hcd: add
SuperSpeed support").
In the case of ClearPortFeature and USB_PORT_FEAT_POWER, simply clear
the right bit regardless of what the wValue is.
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Yuyang Du <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/usb/gadget/udc/dummy_hcd.c | 20 ++++++++------------
1 file changed, 8 insertions(+), 12 deletions(-)
diff --git a/drivers/usb/gadget/udc/dummy_hcd.c b/drivers/usb/gadget/udc/dummy_hcd.c
index b62a3de65075..ff4d6cac7ac0 100644
--- a/drivers/usb/gadget/udc/dummy_hcd.c
+++ b/drivers/usb/gadget/udc/dummy_hcd.c
@@ -2103,16 +2103,13 @@ static int dummy_hub_control(
}
break;
case USB_PORT_FEAT_POWER:
- if (hcd->speed == HCD_USB3) {
- if (dum_hcd->port_status & USB_PORT_STAT_POWER)
- dev_dbg(dummy_dev(dum_hcd),
- "power-off\n");
- } else
- if (dum_hcd->port_status &
- USB_SS_PORT_STAT_POWER)
- dev_dbg(dummy_dev(dum_hcd),
- "power-off\n");
- /* FALLS THROUGH */
+ dev_dbg(dummy_dev(dum_hcd), "power-off\n");
+ if (hcd->speed == HCD_USB3)
+ dum_hcd->port_status &= ~USB_SS_PORT_STAT_POWER;
+ else
+ dum_hcd->port_status &= ~USB_PORT_STAT_POWER;
+ set_link_state(dum_hcd);
+ break;
default:
dum_hcd->port_status &= ~(1 << wValue);
set_link_state(dum_hcd);
@@ -2283,14 +2280,13 @@ static int dummy_hub_control(
if ((dum_hcd->port_status &
USB_SS_PORT_STAT_POWER) != 0) {
dum_hcd->port_status |= (1 << wValue);
- set_link_state(dum_hcd);
}
} else
if ((dum_hcd->port_status &
USB_PORT_STAT_POWER) != 0) {
dum_hcd->port_status |= (1 << wValue);
- set_link_state(dum_hcd);
}
+ set_link_state(dum_hcd);
}
break;
case GetPortErrorCount:
--
2.14.1
From: Aleksandar Markovic <[email protected]>
[ Upstream commit 411dac79cc2ed80f7e348ccc23eb4d8b0ba9f6d5 ]
Add missing clearing of BLTZALL and BGEZALL emulation counters in
function mipsr2_stats_clear_show().
Previously, it was not possible to reset BLTZALL and BGEZALL
emulation counters - their value remained the same even after
explicit request via debugfs. As far as other related counters
are concerned, they all seem to be properly cleared.
This change affects debugfs operation only, core R2 emulation
functionality is not affected.
Signed-off-by: Aleksandar Markovic <[email protected]>
Reviewed-by: Paul Burton <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Patchwork: https://patchwork.linux-mips.org/patch/15517/
Signed-off-by: Ralf Baechle <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/mips/kernel/mips-r2-to-r6-emul.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/mips/kernel/mips-r2-to-r6-emul.c b/arch/mips/kernel/mips-r2-to-r6-emul.c
index 9a46e52864a1..9a4aed652736 100644
--- a/arch/mips/kernel/mips-r2-to-r6-emul.c
+++ b/arch/mips/kernel/mips-r2-to-r6-emul.c
@@ -2339,6 +2339,8 @@ static int mipsr2_stats_clear_show(struct seq_file *s, void *unused)
__this_cpu_write((mipsr2bremustats).bgezl, 0);
__this_cpu_write((mipsr2bremustats).bltzll, 0);
__this_cpu_write((mipsr2bremustats).bgezll, 0);
+ __this_cpu_write((mipsr2bremustats).bltzall, 0);
+ __this_cpu_write((mipsr2bremustats).bgezall, 0);
__this_cpu_write((mipsr2bremustats).bltzal, 0);
__this_cpu_write((mipsr2bremustats).bgezal, 0);
__this_cpu_write((mipsr2bremustats).beql, 0);
--
2.14.1
From: John Stultz <[email protected]>
[ Upstream commit dad3f793f20fbb5c0c342f0f5a0bdf69a4d76089 ]
I had seen some odd behavior with HiKey's usb-gadget interface
that I finally seemed to have chased down. Basically every other
time I plugged in the OTG port, the gadget interface would
properly initialize. The other times, I'd get a big WARN_ON
in dwc2_hsotg_init_fifo() about the fifo_map not being clear.
Ends up if we don't disconnect the gadget state, the fifo-map
doesn't get cleared properly, which causes WARN_ON messages and
also results in the device not properly being setup as a gadget
every other time the OTG port is connected.
So this patch adds a call to dwc2_hsotg_disconnect() in the
reset path so the state is properly cleared.
With it, the gadget interface initializes properly on every
plug in.
Cc: Wei Xu <[email protected]>
Cc: Guodong Xu <[email protected]>
Cc: Amit Pundir <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: John Youn <[email protected]>
Cc: Douglas Anderson <[email protected]>
Cc: Chen Yu <[email protected]>
Cc: Felipe Balbi <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: [email protected]
Acked-by: John Youn <[email protected]>
Signed-off-by: John Stultz <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/usb/dwc2/hcd.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/usb/dwc2/hcd.c b/drivers/usb/dwc2/hcd.c
index df5a06578005..dfc0566bb155 100644
--- a/drivers/usb/dwc2/hcd.c
+++ b/drivers/usb/dwc2/hcd.c
@@ -3220,6 +3220,7 @@ static void dwc2_conn_id_status_change(struct work_struct *work)
dwc2_core_init(hsotg, false);
dwc2_enable_global_interrupts(hsotg);
spin_lock_irqsave(&hsotg->lock, flags);
+ dwc2_hsotg_disconnect(hsotg);
dwc2_hsotg_core_init_disconnected(hsotg, false);
spin_unlock_irqrestore(&hsotg->lock, flags);
dwc2_hsotg_core_connect(hsotg);
--
2.14.1
From: Michael Ellerman <[email protected]>
[ Upstream commit 4868e3508d1934d28961f940ed6b9f1e347ab52c ]
setup_initial_memory_limit() is called from early_init_devtree(), which
runs prior to feature patching. If the kernel is built with CONFIG_JUMP_LABEL=y
and CONFIG_JUMP_LABEL_FEATURE_CHECKS=y then we will potentially get the
wrong value.
If we also have CONFIG_JUMP_LABEL_FEATURE_CHECK_DEBUG=y we get a warning
and backtrace:
Warning! mmu_has_feature() used prior to jump label init!
CPU: 0 PID: 0 Comm: swapper Not tainted 4.11.0-rc4-gccN-next-20170331-g6af2434 #1
Call Trace:
[c000000000fc3d50] [c000000000a26c30] .dump_stack+0xa8/0xe8 (unreliable)
[c000000000fc3de0] [c00000000002e6b8] .setup_initial_memory_limit+0xa4/0x104
[c000000000fc3e60] [c000000000d5c23c] .early_init_devtree+0xd0/0x2f8
[c000000000fc3f00] [c000000000d5d3b0] .early_setup+0x90/0x11c
[c000000000fc3f90] [c000000000000520] start_here_multiplatform+0x68/0x80
Fix it by using early_mmu_has_feature().
Fixes: c12e6f24d413 ("powerpc: Add option to use jump label for mmu_has_feature()")
Signed-off-by: Michael Ellerman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/powerpc/mm/tlb_nohash.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/powerpc/mm/tlb_nohash.c b/arch/powerpc/mm/tlb_nohash.c
index 050badc0ebd3..0b50019505a5 100644
--- a/arch/powerpc/mm/tlb_nohash.c
+++ b/arch/powerpc/mm/tlb_nohash.c
@@ -751,7 +751,7 @@ void setup_initial_memory_limit(phys_addr_t first_memblock_base,
* avoid going over total available memory just in case...
*/
#ifdef CONFIG_PPC_FSL_BOOK3E
- if (mmu_has_feature(MMU_FTR_TYPE_FSL_E)) {
+ if (early_mmu_has_feature(MMU_FTR_TYPE_FSL_E)) {
unsigned long linear_sz;
unsigned int num_cams;
--
2.14.1
From: David Daney <[email protected]>
[ Upstream commit 1ef0910cfd681f0bd0b81f8809935b2006e9cfb9 ]
If bpf_needs_clear_a() returns true, only actually clear it if it is
ever used. If it is not used, we don't save and restore it, so the
clearing has the nasty side effect of clobbering caller state.
Also, don't emit stack pointer adjustment instructions if the
adjustment amount is zero.
Signed-off-by: David Daney <[email protected]>
Cc: James Hogan <[email protected]>
Cc: Alexei Starovoitov <[email protected]>
Cc: Steven J. Hill <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Patchwork: https://patchwork.linux-mips.org/patch/15745/
Signed-off-by: Ralf Baechle <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/mips/net/bpf_jit.c | 16 ++++++++++++----
1 file changed, 12 insertions(+), 4 deletions(-)
diff --git a/arch/mips/net/bpf_jit.c b/arch/mips/net/bpf_jit.c
index 49a2e2226fee..248603739198 100644
--- a/arch/mips/net/bpf_jit.c
+++ b/arch/mips/net/bpf_jit.c
@@ -526,7 +526,8 @@ static void save_bpf_jit_regs(struct jit_ctx *ctx, unsigned offset)
u32 sflags, tmp_flags;
/* Adjust the stack pointer */
- emit_stack_offset(-align_sp(offset), ctx);
+ if (offset)
+ emit_stack_offset(-align_sp(offset), ctx);
tmp_flags = sflags = ctx->flags >> SEEN_SREG_SFT;
/* sflags is essentially a bitmap */
@@ -578,7 +579,8 @@ static void restore_bpf_jit_regs(struct jit_ctx *ctx,
emit_load_stack_reg(r_ra, r_sp, real_off, ctx);
/* Restore the sp and discard the scrach memory */
- emit_stack_offset(align_sp(offset), ctx);
+ if (offset)
+ emit_stack_offset(align_sp(offset), ctx);
}
static unsigned int get_stack_depth(struct jit_ctx *ctx)
@@ -625,8 +627,14 @@ static void build_prologue(struct jit_ctx *ctx)
if (ctx->flags & SEEN_X)
emit_jit_reg_move(r_X, r_zero, ctx);
- /* Do not leak kernel data to userspace */
- if (bpf_needs_clear_a(&ctx->skf->insns[0]))
+ /*
+ * Do not leak kernel data to userspace, we only need to clear
+ * r_A if it is ever used. In fact if it is never used, we
+ * will not save/restore it, so clearing it in this case would
+ * corrupt the state of the caller.
+ */
+ if (bpf_needs_clear_a(&ctx->skf->insns[0]) &&
+ (ctx->flags & SEEN_A))
emit_jit_reg_move(r_A, r_zero, ctx);
}
--
2.14.1
From: Kieran Bingham <[email protected]>
[ Upstream commit 1531a208ed861e4bd287444f9466ffcf98383de2 ]
The DRM object does not register the pipe with the WPF object. This is
used internally throughout the driver as a means of accessing the pipe.
As such this breaks operations which require access to the pipe from WPF
interrupts.
Register the pipe inside the WPF object after it has been declared as
the output.
Fixes: ff7e97c94d9f ("[media] v4l: vsp1: Store pipeline pointer in rwpf")
Signed-off-by: Kieran Bingham <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Signed-off-by: Laurent Pinchart <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/media/platform/vsp1/vsp1_drm.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/media/platform/vsp1/vsp1_drm.c b/drivers/media/platform/vsp1/vsp1_drm.c
index cd209dccff1b..8e2aa3f8e52f 100644
--- a/drivers/media/platform/vsp1/vsp1_drm.c
+++ b/drivers/media/platform/vsp1/vsp1_drm.c
@@ -596,6 +596,7 @@ int vsp1_drm_init(struct vsp1_device *vsp1)
pipe->bru = &vsp1->bru->entity;
pipe->lif = &vsp1->lif->entity;
pipe->output = vsp1->wpf[0];
+ pipe->output->pipe = pipe;
return 0;
}
--
2.14.1
From: Mitch Williams <[email protected]>
[ Upstream commit 004eb614c4d2fcc12a98714fd887a860582f203a ]
The client interface is only intended for use on devices that support
iWarp. Only register with the client if this is the case.
This fixes a panic when loading i40iw on X710 devices.
Signed-off-by: Mitch Williams <[email protected]>
Reported-by: Stefan Assmann <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/intel/i40e/i40e_main.c | 19 +++++++++++--------
1 file changed, 11 insertions(+), 8 deletions(-)
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index becffd15c092..57c7456a5751 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -11142,10 +11142,12 @@ static int i40e_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
round_jiffies(jiffies + pf->service_timer_period));
/* add this PF to client device list and launch a client service task */
- err = i40e_lan_add_device(pf);
- if (err)
- dev_info(&pdev->dev, "Failed to add PF to client API service list: %d\n",
- err);
+ if (pf->flags & I40E_FLAG_IWARP_ENABLED) {
+ err = i40e_lan_add_device(pf);
+ if (err)
+ dev_info(&pdev->dev, "Failed to add PF to client API service list: %d\n",
+ err);
+ }
#ifdef I40E_FCOE
/* create FCoE interface */
@@ -11323,10 +11325,11 @@ static void i40e_remove(struct pci_dev *pdev)
i40e_vsi_release(pf->vsi[pf->lan_vsi]);
/* remove attached clients */
- ret_code = i40e_lan_del_device(pf);
- if (ret_code) {
- dev_warn(&pdev->dev, "Failed to delete client device: %d\n",
- ret_code);
+ if (pf->flags & I40E_FLAG_IWARP_ENABLED) {
+ ret_code = i40e_lan_del_device(pf);
+ if (ret_code)
+ dev_warn(&pdev->dev, "Failed to delete client device: %d\n",
+ ret_code);
}
/* shutdown and destroy the HMC */
--
2.14.1
From: Leonid Yegoshin <[email protected]>
[ Upstream commit 5bba7aa4958e271c3ffceb70d47d3206524cf489 ]
Fix the problem of inaccurate identification of instructions BLEZL and
BGTZL in R2 emulation code by making sure all necessary encoding
specifications are met.
Previously, certain R6 instructions could be identified as BLEZL or
BGTZL. R2 emulation routine didn't take into account that both BLEZL
and BGTZL instructions require their rt field (bits 20 to 16 of
instruction encoding) to be 0, and that, at same time, if the value in
that field is not 0, the encoding may represent a legitimate MIPS R6
instruction.
This means that a problem could occur after emulation optimization,
when emulation routine tried to pipeline emulation, picked up a next
candidate, and subsequently misrecognized an R6 instruction as BLEZL
or BGTZL.
It should be said that for single pass strategy, the problem does not
happen because CPU doesn't trap on branch-compacts which share opcode
space with BLEZL/BGTZL (but have rt field != 0, of course).
Signed-off-by: Leonid Yegoshin <[email protected]>
Signed-off-by: Miodrag Dinic <[email protected]>
Signed-off-by: Aleksandar Markovic <[email protected]>
Reported-by: Douglas Leung <[email protected]>
Reviewed-by: Paul Burton <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Patchwork: https://patchwork.linux-mips.org/patch/15456/
Signed-off-by: Ralf Baechle <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/mips/kernel/mips-r2-to-r6-emul.c | 14 ++++++++++++--
1 file changed, 12 insertions(+), 2 deletions(-)
diff --git a/arch/mips/kernel/mips-r2-to-r6-emul.c b/arch/mips/kernel/mips-r2-to-r6-emul.c
index d8227f289d7f..9a46e52864a1 100644
--- a/arch/mips/kernel/mips-r2-to-r6-emul.c
+++ b/arch/mips/kernel/mips-r2-to-r6-emul.c
@@ -1096,10 +1096,20 @@ repeat:
}
break;
- case beql_op:
- case bnel_op:
case blezl_op:
case bgtzl_op:
+ /*
+ * For BLEZL and BGTZL, rt field must be set to 0. If this
+ * is not the case, this may be an encoding of a MIPS R6
+ * instruction, so return to CPU execution if this occurs
+ */
+ if (MIPSInst_RT(inst)) {
+ err = SIGILL;
+ break;
+ }
+ /* fall through */
+ case beql_op:
+ case bnel_op:
if (delay_slot(regs)) {
err = SIGILL;
break;
--
2.14.1
From: Zhilong Liu <[email protected]>
[ Upstream commit b670883bb9e55ba63a278d83e034faefc01ce2cf ]
md.c: it needs to release the mddev lock before
the array_size_store() returns.
Fixes: ab5a98b132fd ("md-cluster: change array_sectors and update size are not supported")
Signed-off-by: Zhilong Liu <[email protected]>
Reviewed-by: Guoqing Jiang <[email protected]>
Signed-off-by: Shaohua Li <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/md/md.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/md/md.c b/drivers/md/md.c
index 8ebf1b97e1d2..564da422c179 100644
--- a/drivers/md/md.c
+++ b/drivers/md/md.c
@@ -4826,8 +4826,10 @@ array_size_store(struct mddev *mddev, const char *buf, size_t len)
return err;
/* cluster raid doesn't support change array_sectors */
- if (mddev_is_clustered(mddev))
+ if (mddev_is_clustered(mddev)) {
+ mddev_unlock(mddev);
return -EINVAL;
+ }
if (strncmp(buf, "default", 7) == 0) {
if (mddev->pers)
--
2.14.1
From: Alexander Kochetkov <[email protected]>
[ Upstream commit 500d0aa918a2ea6bb918fee8adcf27dc2912bcd1 ]
The clocksource and the sched_clock provided by the arm_global_timer
are quite unstable because their rates depend on the cpu frequency.
On the other side, the arm_global_timer has a higher rating than the
rockchip_timer, it will be selected by default by the time framework
while we want to use the stable rockchip clocksource.
Let's disable the arm_global_timer in order to have the rockchip
clocksource selected by default.
Signed-off-by: Alexander Kochetkov <[email protected]>
Signed-off-by: Daniel Lezcano <[email protected]>
Reviewed-by: Heiko Stuebner <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/rk3188.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/boot/dts/rk3188.dtsi b/arch/arm/boot/dts/rk3188.dtsi
index 31f81b265cef..73a200914f0b 100644
--- a/arch/arm/boot/dts/rk3188.dtsi
+++ b/arch/arm/boot/dts/rk3188.dtsi
@@ -530,6 +530,7 @@
&global_timer {
interrupts = <GIC_PPI 11 0xf04>;
+ status = "disabled";
};
&local_timer {
--
2.14.1
From: Jayachandran C <[email protected]>
[ Upstream commit 7d05587c9e0e4611650bb403812e2d492c178a9f ]
On SMP systems, we see a lot of spurious TX interrupts when a
program generates a steady stream of output to the pl011 UART.
The problem can be easily seen when one CPU generates the output
while another CPU handles the pl011 interrupts, and the rate of
output is low enough not to fill the TX FIFO. The problem seems
to be:
-- CPU a -- -- CPU b --
(take port lock)
pl011_start_tx
pl011_start_tx_pio
enable TXIM in REG_IMSC -> causes uart tx intr (pl011_int)
pl011_tx_chars pl011_int
...tx chars, all done... (wait for port lock)
pl011_stop_tx .
disable TXIM .
(release port lock) -> (take port lock)
check for TXIM, not enabled
(release port lock)
return IRQ_NONE
Enabling the TXIM in pl011_start_tx_pio() causes the interrupt
to be generated and delivered to CPU b, even though pl011_tx_chars()
is able to complete the TX and then disable the tx interrupt.
Fix this by enabling TXIM only after pl011_tx_chars, if it is needed.
pl011_tx_chars will return a boolean indicating whether the TX
interrupts have to be enabled.
Debugged-by: Vijaya Kumar <[email protected]>
Signed-off-by: Jayachandran C <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/tty/serial/amba-pl011.c | 23 ++++++++++++++---------
1 file changed, 14 insertions(+), 9 deletions(-)
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index e2c33b9528d8..b42d7f1c9089 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -1302,14 +1302,15 @@ static void pl011_stop_tx(struct uart_port *port)
pl011_dma_tx_stop(uap);
}
-static void pl011_tx_chars(struct uart_amba_port *uap, bool from_irq);
+static bool pl011_tx_chars(struct uart_amba_port *uap, bool from_irq);
/* Start TX with programmed I/O only (no DMA) */
static void pl011_start_tx_pio(struct uart_amba_port *uap)
{
- uap->im |= UART011_TXIM;
- pl011_write(uap->im, uap, REG_IMSC);
- pl011_tx_chars(uap, false);
+ if (pl011_tx_chars(uap, false)) {
+ uap->im |= UART011_TXIM;
+ pl011_write(uap->im, uap, REG_IMSC);
+ }
}
static void pl011_start_tx(struct uart_port *port)
@@ -1389,25 +1390,26 @@ static bool pl011_tx_char(struct uart_amba_port *uap, unsigned char c,
return true;
}
-static void pl011_tx_chars(struct uart_amba_port *uap, bool from_irq)
+/* Returns true if tx interrupts have to be (kept) enabled */
+static bool pl011_tx_chars(struct uart_amba_port *uap, bool from_irq)
{
struct circ_buf *xmit = &uap->port.state->xmit;
int count = uap->fifosize >> 1;
if (uap->port.x_char) {
if (!pl011_tx_char(uap, uap->port.x_char, from_irq))
- return;
+ return true;
uap->port.x_char = 0;
--count;
}
if (uart_circ_empty(xmit) || uart_tx_stopped(&uap->port)) {
pl011_stop_tx(&uap->port);
- return;
+ return false;
}
/* If we are using DMA mode, try to send some characters. */
if (pl011_dma_tx_irq(uap))
- return;
+ return true;
do {
if (likely(from_irq) && count-- == 0)
@@ -1422,8 +1424,11 @@ static void pl011_tx_chars(struct uart_amba_port *uap, bool from_irq)
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&uap->port);
- if (uart_circ_empty(xmit))
+ if (uart_circ_empty(xmit)) {
pl011_stop_tx(&uap->port);
+ return false;
+ }
+ return true;
}
static void pl011_modem_status(struct uart_amba_port *uap)
--
2.14.1
From: Kieran Bingham <[email protected]>
[ Upstream commit 4461c84b52b4a952c657505ef7e4e06b016783df ]
With multiple inputs through the BRU it is feasible for the streams to
race each other at stream-on.
Multiple VIDIOC_STREAMON calls racing each other could have process
N-1 skipping over the pipeline setup section and then start the pipeline
early, if videobuf2 has already enqueued buffers to the driver for
process N but not called the .start_streaming() operation yet
In the case of the video pipelines, this
can present two serious issues.
1) A null-dereference if the pipe->dl is committed at the same time as
the vsp1_video_setup_pipeline() is processing
2) A hardware hang, where a display list is committed without having
called vsp1_video_setup_pipeline() first
Repair this issue, by ensuring that only the stream which configures the
pipeline is able to start it.
Signed-off-by: Kieran Bingham <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/media/platform/vsp1/vsp1_video.c | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/drivers/media/platform/vsp1/vsp1_video.c b/drivers/media/platform/vsp1/vsp1_video.c
index d351b9c768d2..743aa0febc09 100644
--- a/drivers/media/platform/vsp1/vsp1_video.c
+++ b/drivers/media/platform/vsp1/vsp1_video.c
@@ -792,6 +792,7 @@ static int vsp1_video_start_streaming(struct vb2_queue *vq, unsigned int count)
{
struct vsp1_video *video = vb2_get_drv_priv(vq);
struct vsp1_pipeline *pipe = video->rwpf->pipe;
+ bool start_pipeline = false;
unsigned long flags;
int ret;
@@ -802,11 +803,23 @@ static int vsp1_video_start_streaming(struct vb2_queue *vq, unsigned int count)
mutex_unlock(&pipe->lock);
return ret;
}
+
+ start_pipeline = true;
}
pipe->stream_count++;
mutex_unlock(&pipe->lock);
+ /*
+ * vsp1_pipeline_ready() is not sufficient to establish that all streams
+ * are prepared and the pipeline is configured, as multiple streams
+ * can race through streamon with buffers already queued; Therefore we
+ * don't even attempt to start the pipeline until the last stream has
+ * called through here.
+ */
+ if (!start_pipeline)
+ return 0;
+
spin_lock_irqsave(&pipe->irqlock, flags);
if (vsp1_pipeline_ready(pipe))
vsp1_video_pipeline_run(pipe);
--
2.14.1
From: NeilBrown <[email protected]>
[ Upstream commit 7471fb77ce4dc4cb81291189947fcdf621a97987 ]
When recoverying a single missing/failed device in a RAID6,
those stripes where the Q block is on the missing device are
handled a bit differently. In these cases it is easy to
check that the P block is correct, so we do. This results
in the P block be destroy. Consequently the P block needs
to be read a second time in order to compute Q. This causes
lots of seeks and hurts performance.
It shouldn't be necessary to re-read P as it can be computed
from the DATA. But we only compute blocks on missing
devices, since c337869d9501 ("md: do not compute parity
unless it is on a failed drive").
So relax the change made in that commit to allow computing
of the P block in a RAID6 which it is the only missing that
block.
This makes RAID6 recovery run much faster as the disk just
"before" the recovering device is no longer seeking
back-and-forth.
Reported-by-tested-by: Brad Campbell <[email protected]>
Reviewed-by: Dan Williams <[email protected]>
Signed-off-by: NeilBrown <[email protected]>
Signed-off-by: Shaohua Li <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/md/raid5.c | 13 ++++++++++++-
1 file changed, 12 insertions(+), 1 deletion(-)
diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c
index 475a7a1bcfe0..4493be50fc6a 100644
--- a/drivers/md/raid5.c
+++ b/drivers/md/raid5.c
@@ -3391,9 +3391,20 @@ static int fetch_block(struct stripe_head *sh, struct stripe_head_state *s,
BUG_ON(test_bit(R5_Wantcompute, &dev->flags));
BUG_ON(test_bit(R5_Wantread, &dev->flags));
BUG_ON(sh->batch_head);
+
+ /*
+ * In the raid6 case if the only non-uptodate disk is P
+ * then we already trusted P to compute the other failed
+ * drives. It is safe to compute rather than re-read P.
+ * In other cases we only compute blocks from failed
+ * devices, otherwise check/repair might fail to detect
+ * a real inconsistency.
+ */
+
if ((s->uptodate == disks - 1) &&
+ ((sh->qd_idx >= 0 && sh->pd_idx == disk_idx) ||
(s->failed && (disk_idx == s->failed_num[0] ||
- disk_idx == s->failed_num[1]))) {
+ disk_idx == s->failed_num[1])))) {
/* have disk failed, and we're requested to fetch it;
* do compute it
*/
--
2.14.1
From: Christopher James Halse Rogers <[email protected]>
[ Upstream commit 1769152ac64b0b07583f696b621624df2ca4c840 ]
Any use of the framebuffer will migrate it to VRAM, which is not sensible for
an imported dma-buf.
v2: Use DRM_DEBUG_KMS to prevent userspace accidentally spamming dmesg.
Reviewed-by: Michel Dänzer <[email protected]>
Reviewed-by: Christian König <[email protected]>
Signed-off-by: Christopher James Halse Rogers <[email protected]>
CC: [email protected]
Signed-off-by: Alex Deucher <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/gpu/drm/amd/amdgpu/amdgpu_display.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/gpu/drm/amd/amdgpu/amdgpu_display.c b/drivers/gpu/drm/amd/amdgpu/amdgpu_display.c
index 083e2b429872..15a2d8f3725d 100644
--- a/drivers/gpu/drm/amd/amdgpu/amdgpu_display.c
+++ b/drivers/gpu/drm/amd/amdgpu/amdgpu_display.c
@@ -533,6 +533,12 @@ amdgpu_user_framebuffer_create(struct drm_device *dev,
return ERR_PTR(-ENOENT);
}
+ /* Handle is imported dma-buf, so cannot be migrated to VRAM for scanout */
+ if (obj->import_attach) {
+ DRM_DEBUG_KMS("Cannot create framebuffer from imported dma_buf\n");
+ return ERR_PTR(-EINVAL);
+ }
+
amdgpu_fb = kzalloc(sizeof(*amdgpu_fb), GFP_KERNEL);
if (amdgpu_fb == NULL) {
drm_gem_object_unreference_unlocked(obj);
--
2.14.1
From: Christopher James Halse Rogers <[email protected]>
[ Upstream commit a294043b2fbd8de69d161457ed0c7a4026bbfa5a ]
Any use of the framebuffer will migrate it to VRAM, which is not sensible for
an imported dma-buf.
v2: Use DRM_DEBUG_KMS to prevent userspace accidentally spamming dmesg.
Reviewed-by: Michel Dänzer <[email protected]>
Reviewed-by: Christian König <[email protected]>
Signed-off-by: Christopher James Halse Rogers <[email protected]>
CC: [email protected]
Signed-off-by: Alex Deucher <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/gpu/drm/radeon/radeon_display.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/gpu/drm/radeon/radeon_display.c b/drivers/gpu/drm/radeon/radeon_display.c
index cdb8cb568c15..ca1caf405832 100644
--- a/drivers/gpu/drm/radeon/radeon_display.c
+++ b/drivers/gpu/drm/radeon/radeon_display.c
@@ -1352,6 +1352,12 @@ radeon_user_framebuffer_create(struct drm_device *dev,
return ERR_PTR(-ENOENT);
}
+ /* Handle is imported dma-buf, so cannot be migrated to VRAM for scanout */
+ if (obj->import_attach) {
+ DRM_DEBUG_KMS("Cannot create framebuffer from imported dma_buf\n");
+ return ERR_PTR(-EINVAL);
+ }
+
radeon_fb = kzalloc(sizeof(*radeon_fb), GFP_KERNEL);
if (radeon_fb == NULL) {
drm_gem_object_unreference_unlocked(obj);
--
2.14.1
From: Arnd Bergmann <[email protected]>
[ Upstream commit 7064dc7fc13b2994d33ae540ffb7a3a05ac463bf ]
I ran into a link error on ARM64 for lkdtm_rodata_do_nothing:
drivers/misc/built-in.o: In function `lkdtm_rodata_do_nothing':
:(.rodata+0x68c8): relocation truncated to fit: R_AARCH64_CALL26 against symbol `__sanitizer_cov_trace_pc' defined in .text section in kernel/built-in.o
I did not analyze this further, but my theory is that we would need a trampoline
to call __sanitizer_cov_trace_pc(), but the linker (correctly) only adds trampolines
for callers in executable sections.
Disabling KCOV for this one file avoids the build failure with no
other practical downsides I can think of.
The problem can only happen on kernels that contain both kcov and
lkdtm, so if we want to backport this, it should be in the earliest
version that has both (v4.8).
Fixes: 5c9a8750a640 ("kernel: add kcov code coverage")
Fixes: 9a49a528dcf3 ("lkdtm: add function for testing .rodata section")
Signed-off-by: Arnd Bergmann <[email protected]>
Acked-by: Dmitry Vyukov <[email protected]>
Acked-by: Kees Cook <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/misc/Makefile | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
index 31983366090a..2bf79ba4a39e 100644
--- a/drivers/misc/Makefile
+++ b/drivers/misc/Makefile
@@ -61,6 +61,8 @@ lkdtm-$(CONFIG_LKDTM) += lkdtm_perms.o
lkdtm-$(CONFIG_LKDTM) += lkdtm_rodata_objcopy.o
lkdtm-$(CONFIG_LKDTM) += lkdtm_usercopy.o
+KCOV_INSTRUMENT_lkdtm_rodata.o := n
+
OBJCOPYFLAGS :=
OBJCOPYFLAGS_lkdtm_rodata_objcopy.o := \
--set-section-flags .text=alloc,readonly \
--
2.14.1
From: Borislav Petkov <[email protected]>
[ Upstream commit 74f169090b6f36b867c9df0454366dd9af6f62d1 ]
MCG_CAP[63:9] bits are reserved on AMD. However, on an AMD guest, this
MSR returns 0x100010a. More specifically, bit 24 is set, which is simply
wrong. That bit is MCG_SER_P and is present only on Intel. Thus, clean
up the reserved bits in order not to confuse guests.
Signed-off-by: Borislav Petkov <[email protected]>
Cc: Joerg Roedel <[email protected]>
Cc: Paolo Bonzini <[email protected]>
Cc: Radim Krčmář <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/x86/kvm/svm.c | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/arch/x86/kvm/svm.c b/arch/x86/kvm/svm.c
index be644afab1bb..68381824c565 100644
--- a/arch/x86/kvm/svm.c
+++ b/arch/x86/kvm/svm.c
@@ -5448,6 +5448,12 @@ static inline void avic_post_state_restore(struct kvm_vcpu *vcpu)
avic_handle_ldr_update(vcpu);
}
+static void svm_setup_mce(struct kvm_vcpu *vcpu)
+{
+ /* [63:9] are reserved. */
+ vcpu->arch.mcg_cap &= 0x1ff;
+}
+
static struct kvm_x86_ops svm_x86_ops __ro_after_init = {
.cpu_has_kvm_support = has_svm,
.disabled_by_bios = is_disabled,
@@ -5563,6 +5569,7 @@ static struct kvm_x86_ops svm_x86_ops __ro_after_init = {
.pmu_ops = &amd_pmu_ops,
.deliver_posted_interrupt = svm_deliver_avic_intr,
.update_pi_irte = svm_update_pi_irte,
+ .setup_mce = svm_setup_mce,
};
static int __init svm_init(void)
--
2.14.1
From: Jim Mattson <[email protected]>
[ Upstream commit 28d06353881939703c34d82a1465136af176c620 ]
The userspace exception injection API and code path are entirely
unprepared for exceptions that might cause a VM-exit from L2 to L1, so
the best course of action may be to simply disallow this for now.
1. The API provides no mechanism for userspace to specify the new DR6
bits for a #DB exception or the new CR2 value for a #PF
exception. Presumably, userspace is expected to modify these registers
directly with KVM_SET_SREGS before the next KVM_RUN ioctl. However, in
the event that L1 intercepts the exception, these registers should not
be changed. Instead, the new values should be provided in the
exit_qualification field of vmcs12 (Intel SDM vol 3, section 27.1).
2. In the case of a userspace-injected #DB, inject_pending_event()
clears DR7.GD before calling vmx_queue_exception(). However, in the
event that L1 intercepts the exception, this is too early, because
DR7.GD should not be modified by a #DB that causes a VM-exit directly
(Intel SDM vol 3, section 27.1).
3. If the injected exception is a #PF, nested_vmx_check_exception()
doesn't properly check whether or not L1 is interested in the
associated error code (using the #PF error code mask and match fields
from vmcs12). It may either return 0 when it should call
nested_vmx_vmexit() or vice versa.
4. nested_vmx_check_exception() assumes that it is dealing with a
hardware-generated exception intercept from L2, with some of the
relevant details (the VM-exit interruption-information and the exit
qualification) live in vmcs02. For userspace-injected exceptions, this
is not the case.
5. prepare_vmcs12() assumes that when its exit_intr_info argument
specifies valid information with a valid error code that it can VMREAD
the VM-exit interruption error code from vmcs02. For
userspace-injected exceptions, this is not the case.
Signed-off-by: Jim Mattson <[email protected]>
Signed-off-by: Radim Krčmář <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/x86/kvm/x86.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c
index 4b19ec1da22d..3aaaf305420d 100644
--- a/arch/x86/kvm/x86.c
+++ b/arch/x86/kvm/x86.c
@@ -3070,7 +3070,8 @@ static int kvm_vcpu_ioctl_x86_set_vcpu_events(struct kvm_vcpu *vcpu,
return -EINVAL;
if (events->exception.injected &&
- (events->exception.nr > 31 || events->exception.nr == NMI_VECTOR))
+ (events->exception.nr > 31 || events->exception.nr == NMI_VECTOR ||
+ is_guest_mode(vcpu)))
return -EINVAL;
/* INITs are latched while in SMM */
--
2.14.1
From: Jeffy Chen <[email protected]>
[ Upstream commit 5e570373c015b60a68828b1cd9d475cb33d3be4b ]
We're trying to access vop registers here, so need to make sure
the pm domain is on.
Normally it should be enabled by the bootloader, but there's no
guarantee of it. And if we wanna do unbind/bind, it would also
cause the device to hang.
And this patch also does these:
1/ move vop_initial to the end of vop_bind for eaiser error handling.
2/ correct the err_put_pm_runtime of vop_enable.
Signed-off-by: Jeffy Chen <[email protected]>
Signed-off-by: Sean Paul <[email protected]>
Link: http://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/gpu/drm/rockchip/rockchip_drm_vop.c | 29 +++++++++++++++++++++--------
1 file changed, 21 insertions(+), 8 deletions(-)
diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
index c7eba305c488..6e3c4acb16ac 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
@@ -503,7 +503,7 @@ static int vop_enable(struct drm_crtc *crtc)
ret = pm_runtime_get_sync(vop->dev);
if (ret < 0) {
dev_err(vop->dev, "failed to get pm runtime: %d\n", ret);
- goto err_put_pm_runtime;
+ return ret;
}
ret = clk_enable(vop->hclk);
@@ -1348,10 +1348,16 @@ static int vop_initial(struct vop *vop)
return PTR_ERR(vop->dclk);
}
+ ret = pm_runtime_get_sync(vop->dev);
+ if (ret < 0) {
+ dev_err(vop->dev, "failed to get pm runtime: %d\n", ret);
+ return ret;
+ }
+
ret = clk_prepare(vop->dclk);
if (ret < 0) {
dev_err(vop->dev, "failed to prepare dclk\n");
- return ret;
+ goto err_put_pm_runtime;
}
/* Enable both the hclk and aclk to setup the vop */
@@ -1411,6 +1417,8 @@ static int vop_initial(struct vop *vop)
vop->is_enabled = false;
+ pm_runtime_put_sync(vop->dev);
+
return 0;
err_disable_aclk:
@@ -1419,6 +1427,8 @@ err_disable_hclk:
clk_disable_unprepare(vop->hclk);
err_unprepare_dclk:
clk_unprepare(vop->dclk);
+err_put_pm_runtime:
+ pm_runtime_put_sync(vop->dev);
return ret;
}
@@ -1519,12 +1529,6 @@ static int vop_bind(struct device *dev, struct device *master, void *data)
if (!vop->regsbak)
return -ENOMEM;
- ret = vop_initial(vop);
- if (ret < 0) {
- dev_err(&pdev->dev, "cannot initial vop dev - err %d\n", ret);
- return ret;
- }
-
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
dev_err(dev, "cannot find irq for vop\n");
@@ -1551,8 +1555,17 @@ static int vop_bind(struct device *dev, struct device *master, void *data)
pm_runtime_enable(&pdev->dev);
+ ret = vop_initial(vop);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "cannot initial vop dev - err %d\n", ret);
+ goto err_disable_pm_runtime;
+ }
+
return 0;
+err_disable_pm_runtime:
+ pm_runtime_disable(&pdev->dev);
+ vop_destroy_crtc(vop);
err_enable_irq:
enable_irq(vop->irq); /* To balance out the disable_irq above */
return ret;
--
2.14.1
From: Liam Beguin <[email protected]>
[ Upstream commit 9a1c779e6b06855e41099caa6f15b3b584dfa88c ]
This patch forces the frambuffer size to be aligned on kernel pages.
During the board startup, the splash screed did appear;
the "ts_test" program or our application were not able to start.
The following error message was reported:
error: failed to map framebuffer device to memory.
LinuxFB: driver cannot connect
The issue was discovered, on the LPC32xx platform, during the migration
of the LCD definition from the board file to the device tree.
Signed-off-by: Liam Beguin <[email protected]>
Signed-off-by: Sylvain Lemieux <[email protected]>
Cc: Vladimir Zapolskiy <[email protected]>
Cc: Russell King <[email protected]>
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/video/fbdev/amba-clcd.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/video/fbdev/amba-clcd.c b/drivers/video/fbdev/amba-clcd.c
index ec2671d98abc..89880b70cc28 100644
--- a/drivers/video/fbdev/amba-clcd.c
+++ b/drivers/video/fbdev/amba-clcd.c
@@ -892,8 +892,8 @@ static int clcdfb_of_dma_setup(struct clcd_fb *fb)
if (err)
return err;
- framesize = fb->panel->mode.xres * fb->panel->mode.yres *
- fb->panel->bpp / 8;
+ framesize = PAGE_ALIGN(fb->panel->mode.xres * fb->panel->mode.yres *
+ fb->panel->bpp / 8);
fb->fb.screen_base = dma_alloc_coherent(&fb->dev->dev, framesize,
&dma, GFP_KERNEL);
if (!fb->fb.screen_base)
--
2.14.1
From: John Johansen <[email protected]>
[ Upstream commit 622f6e3265707ebf02ba776ac6e68003bcc31213 ]
The path_max parameter determines the max size of buffers allocated
but it should not be setable at run time. If can be used to cause an
oops
root@ubuntu:~# echo 16777216 > /sys/module/apparmor/parameters/path_max
root@ubuntu:~# cat /sys/module/apparmor/parameters/path_max
Killed
[ 122.141911] BUG: unable to handle kernel paging request at ffff880080945fff
[ 122.143497] IP: [<ffffffff81228844>] d_absolute_path+0x44/0xa0
[ 122.144742] PGD 220c067 PUD 0
[ 122.145453] Oops: 0002 [#1] SMP
[ 122.146204] Modules linked in: vmw_vsock_vmci_transport vsock ppdev vmw_balloon snd_ens1371 btusb snd_ac97_codec gameport snd_rawmidi btrtl snd_seq_device ac97_bus btbcm btintel snd_pcm input_leds bluetooth snd_timer snd joydev soundcore serio_raw coretemp shpchp nfit parport_pc i2c_piix4 8250_fintek vmw_vmci parport mac_hid ib_iser rdma_cm iw_cm ib_cm ib_sa ib_mad ib_core ib_addr iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi autofs4 btrfs raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 multipath linear hid_generic usbhid hid crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel aes_x86_64 lrw gf128mul glue_helper ablk_helper cryptd vmwgfx psmouse mptspi ttm mptscsih drm_kms_helper mptbase syscopyarea scsi_transport_spi sysfillrect
[ 122.163365] ahci sysimgblt e1000 fb_sys_fops libahci drm pata_acpi fjes
[ 122.164747] CPU: 3 PID: 1501 Comm: bash Not tainted 4.4.0-59-generic #80-Ubuntu
[ 122.166250] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/02/2015
[ 122.168611] task: ffff88003496aa00 ti: ffff880076474000 task.ti: ffff880076474000
[ 122.170018] RIP: 0010:[<ffffffff81228844>] [<ffffffff81228844>] d_absolute_path+0x44/0xa0
[ 122.171525] RSP: 0018:ffff880076477b90 EFLAGS: 00010206
[ 122.172462] RAX: ffff880080945fff RBX: 0000000000000000 RCX: 0000000001000000
[ 122.173709] RDX: 0000000000ffffff RSI: ffff880080946000 RDI: ffff8800348a1010
[ 122.174978] RBP: ffff880076477bb8 R08: ffff880076477c80 R09: 0000000000000000
[ 122.176227] R10: 00007ffffffff000 R11: ffff88007f946000 R12: ffff88007f946000
[ 122.177496] R13: ffff880076477c80 R14: ffff8800348a1010 R15: ffff8800348a2400
[ 122.178745] FS: 00007fd459eb4700(0000) GS:ffff88007b6c0000(0000) knlGS:0000000000000000
[ 122.180176] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 122.181186] CR2: ffff880080945fff CR3: 0000000073422000 CR4: 00000000001406e0
[ 122.182469] Stack:
[ 122.182843] 00ffffff00000001 ffff880080946000 0000000000000000 0000000000000000
[ 122.184409] 00000000570f789c ffff880076477c30 ffffffff81385671 ffff88007a2e7a58
[ 122.185810] 0000000000000000 ffff880076477c88 01000000008a1000 0000000000000000
[ 122.187231] Call Trace:
[ 122.187680] [<ffffffff81385671>] aa_path_name+0x81/0x370
[ 122.188637] [<ffffffff813875dd>] profile_transition+0xbd/0xb80
[ 122.190181] [<ffffffff811af9bc>] ? zone_statistics+0x7c/0xa0
[ 122.191674] [<ffffffff81389b20>] apparmor_bprm_set_creds+0x9b0/0xac0
[ 122.193288] [<ffffffff812e1971>] ? ext4_xattr_get+0x81/0x220
[ 122.194793] [<ffffffff812e800c>] ? ext4_xattr_security_get+0x1c/0x30
[ 122.196392] [<ffffffff813449b9>] ? get_vfs_caps_from_disk+0x69/0x110
[ 122.198004] [<ffffffff81232d4f>] ? mnt_may_suid+0x3f/0x50
[ 122.199737] [<ffffffff81344b03>] ? cap_bprm_set_creds+0xa3/0x600
[ 122.201377] [<ffffffff81346e53>] security_bprm_set_creds+0x33/0x50
[ 122.203024] [<ffffffff81214ce5>] prepare_binprm+0x85/0x190
[ 122.204515] [<ffffffff81216545>] do_execveat_common.isra.33+0x485/0x710
[ 122.206200] [<ffffffff81216a6a>] SyS_execve+0x3a/0x50
[ 122.207615] [<ffffffff81838795>] stub_execve+0x5/0x5
[ 122.208978] [<ffffffff818384f2>] ? entry_SYSCALL_64_fastpath+0x16/0x71
[ 122.210615] Code: f8 31 c0 48 63 c2 83 ea 01 48 c7 45 e8 00 00 00 00 48 01 c6 85 d2 48 c7 45 f0 00 00 00 00 48 89 75 e0 89 55 dc 78 0c 48 8d 46 ff <c6> 46 ff 00 48 89 45 e0 48 8d 55 e0 48 8d 4d dc 48 8d 75 e8 e8
[ 122.217320] RIP [<ffffffff81228844>] d_absolute_path+0x44/0xa0
[ 122.218860] RSP <ffff880076477b90>
[ 122.219919] CR2: ffff880080945fff
[ 122.220936] ---[ end trace 506cdbd85eb6c55e ]---
Reported-by: Tetsuo Handa <[email protected]>
Signed-off-by: John Johansen <[email protected]>
Signed-off-by: James Morris <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
security/apparmor/lsm.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/security/apparmor/lsm.c b/security/apparmor/lsm.c
index 7d3a98b2d55a..02cc952b86aa 100644
--- a/security/apparmor/lsm.c
+++ b/security/apparmor/lsm.c
@@ -707,7 +707,7 @@ module_param_named(logsyscall, aa_g_logsyscall, aabool, S_IRUSR | S_IWUSR);
/* Maximum pathname length before accesses will start getting rejected */
unsigned int aa_g_path_max = 2 * PATH_MAX;
-module_param_named(path_max, aa_g_path_max, aauint, S_IRUSR | S_IWUSR);
+module_param_named(path_max, aa_g_path_max, aauint, S_IRUSR);
/* Determines how paranoid loading of policy is and how much verification
* on the loaded policy is done.
--
2.14.1
From: Jan Kara <[email protected]>
[ Upstream commit 71b0576bdb862e964a82c73327cdd1a249c53e67 ]
Currently canceling of delayed work that flushes old data using
cancel_old_flush() does not prevent work from being requeued. Thus
in theory new work can be queued after cancel_old_flush() from
reiserfs_freeze() has run. This will become larger problem once
flush_old_commits() can requeue the work itself.
Fix the problem by recording in sbi->work_queue that flushing work is
canceled and should not be requeued.
Signed-off-by: Jan Kara <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
fs/reiserfs/journal.c | 2 +-
fs/reiserfs/reiserfs.h | 1 +
fs/reiserfs/super.c | 21 +++++++++++++++------
3 files changed, 17 insertions(+), 7 deletions(-)
diff --git a/fs/reiserfs/journal.c b/fs/reiserfs/journal.c
index bc2dde2423c2..76108185854e 100644
--- a/fs/reiserfs/journal.c
+++ b/fs/reiserfs/journal.c
@@ -1959,7 +1959,7 @@ static int do_journal_release(struct reiserfs_transaction_handle *th,
* will be requeued because superblock is being shutdown and doesn't
* have MS_ACTIVE set.
*/
- cancel_delayed_work_sync(&REISERFS_SB(sb)->old_work);
+ reiserfs_cancel_old_flush(sb);
/* wait for all commits to finish */
cancel_delayed_work_sync(&SB_JOURNAL(sb)->j_work);
diff --git a/fs/reiserfs/reiserfs.h b/fs/reiserfs/reiserfs.h
index 5dcf3ab83886..6ca00471afbf 100644
--- a/fs/reiserfs/reiserfs.h
+++ b/fs/reiserfs/reiserfs.h
@@ -2948,6 +2948,7 @@ int reiserfs_allocate_list_bitmaps(struct super_block *s,
struct reiserfs_list_bitmap *, unsigned int);
void reiserfs_schedule_old_flush(struct super_block *s);
+void reiserfs_cancel_old_flush(struct super_block *s);
void add_save_link(struct reiserfs_transaction_handle *th,
struct inode *inode, int truncate);
int remove_save_link(struct inode *inode, int truncate);
diff --git a/fs/reiserfs/super.c b/fs/reiserfs/super.c
index e101d70d2327..dec6c93044fa 100644
--- a/fs/reiserfs/super.c
+++ b/fs/reiserfs/super.c
@@ -90,7 +90,9 @@ static void flush_old_commits(struct work_struct *work)
s = sbi->s_journal->j_work_sb;
spin_lock(&sbi->old_work_lock);
- sbi->work_queued = 0;
+ /* Avoid clobbering the cancel state... */
+ if (sbi->work_queued == 1)
+ sbi->work_queued = 0;
spin_unlock(&sbi->old_work_lock);
reiserfs_sync_fs(s, 1);
@@ -117,21 +119,22 @@ void reiserfs_schedule_old_flush(struct super_block *s)
spin_unlock(&sbi->old_work_lock);
}
-static void cancel_old_flush(struct super_block *s)
+void reiserfs_cancel_old_flush(struct super_block *s)
{
struct reiserfs_sb_info *sbi = REISERFS_SB(s);
- cancel_delayed_work_sync(&REISERFS_SB(s)->old_work);
spin_lock(&sbi->old_work_lock);
- sbi->work_queued = 0;
+ /* Make sure no new flushes will be queued */
+ sbi->work_queued = 2;
spin_unlock(&sbi->old_work_lock);
+ cancel_delayed_work_sync(&REISERFS_SB(s)->old_work);
}
static int reiserfs_freeze(struct super_block *s)
{
struct reiserfs_transaction_handle th;
- cancel_old_flush(s);
+ reiserfs_cancel_old_flush(s);
reiserfs_write_lock(s);
if (!(s->s_flags & MS_RDONLY)) {
@@ -152,7 +155,13 @@ static int reiserfs_freeze(struct super_block *s)
static int reiserfs_unfreeze(struct super_block *s)
{
+ struct reiserfs_sb_info *sbi = REISERFS_SB(s);
+
reiserfs_allow_writes(s);
+ spin_lock(&sbi->old_work_lock);
+ /* Allow old_work to run again */
+ sbi->work_queued = 0;
+ spin_unlock(&sbi->old_work_lock);
return 0;
}
@@ -2194,7 +2203,7 @@ error_unlocked:
if (sbi->commit_wq)
destroy_workqueue(sbi->commit_wq);
- cancel_delayed_work_sync(&REISERFS_SB(s)->old_work);
+ reiserfs_cancel_old_flush(s);
reiserfs_free_bitmap_cache(s);
if (SB_BUFFER_WITH_SB(s))
--
2.14.1
From: Phil Turnbull <[email protected]>
[ Upstream commit 540fca35e38d15777b310f450f63f056e63039f5 ]
FM10K_REMOVED expects a hardware address, not a 'struct fm10k_hw'.
Fixes: 5cb8db4a4cbc ("fm10k: Add support for VF")
Signed-off-by: Phil Turnbull <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/intel/fm10k/fm10k_ethtool.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/intel/fm10k/fm10k_ethtool.c b/drivers/net/ethernet/intel/fm10k/fm10k_ethtool.c
index 5241e0873397..7041d83d48bf 100644
--- a/drivers/net/ethernet/intel/fm10k/fm10k_ethtool.c
+++ b/drivers/net/ethernet/intel/fm10k/fm10k_ethtool.c
@@ -942,7 +942,7 @@ static void fm10k_self_test(struct net_device *dev,
memset(data, 0, sizeof(*data) * FM10K_TEST_LEN);
- if (FM10K_REMOVED(hw)) {
+ if (FM10K_REMOVED(hw->hw_addr)) {
netif_err(interface, drv, dev,
"Interface removed - test blocked\n");
eth_test->flags |= ETH_TEST_FL_FAILED;
--
2.14.1
From: Thor Thayer <[email protected]>
[ Upstream commit 25b223ddfe2a557307c05fe673e09d94ae950877 ]
The peripherals' RAS functionality only exist on the Arria10 SoCFPGA.
The Cyclone5 initialization generates EDAC warnings when the peripherals
aren't found in the device tree. Fix by checking for Arria10 in the init
functions.
Signed-off-by: Thor Thayer <[email protected]>
Cc: linux-edac <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Borislav Petkov <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/edac/altera_edac.c | 22 ++++++++++++++++++----
1 file changed, 18 insertions(+), 4 deletions(-)
diff --git a/drivers/edac/altera_edac.c b/drivers/edac/altera_edac.c
index 58d3e2b39b5b..61262a7a5c3a 100644
--- a/drivers/edac/altera_edac.c
+++ b/drivers/edac/altera_edac.c
@@ -1020,13 +1020,23 @@ out:
return ret;
}
+static int socfpga_is_a10(void)
+{
+ return of_machine_is_compatible("altr,socfpga-arria10");
+}
+
static int validate_parent_available(struct device_node *np);
static const struct of_device_id altr_edac_a10_device_of_match[];
static int __init __maybe_unused altr_init_a10_ecc_device_type(char *compat)
{
int irq;
- struct device_node *child, *np = of_find_compatible_node(NULL, NULL,
- "altr,socfpga-a10-ecc-manager");
+ struct device_node *child, *np;
+
+ if (!socfpga_is_a10())
+ return -ENODEV;
+
+ np = of_find_compatible_node(NULL, NULL,
+ "altr,socfpga-a10-ecc-manager");
if (!np) {
edac_printk(KERN_ERR, EDAC_DEVICE, "ECC Manager not found\n");
return -ENODEV;
@@ -1542,8 +1552,12 @@ static const struct edac_device_prv_data a10_sdmmceccb_data = {
static int __init socfpga_init_sdmmc_ecc(void)
{
int rc = -ENODEV;
- struct device_node *child = of_find_compatible_node(NULL, NULL,
- "altr,socfpga-sdmmc-ecc");
+ struct device_node *child;
+
+ if (!socfpga_is_a10())
+ return -ENODEV;
+
+ child = of_find_compatible_node(NULL, NULL, "altr,socfpga-sdmmc-ecc");
if (!child) {
edac_printk(KERN_WARNING, EDAC_DEVICE, "SDMMC node not found\n");
return -ENODEV;
--
2.14.1
From: Nate Watterson <[email protected]>
[ Upstream commit 5016bdb796b3726eec043ca0ce3be981f712c756 ]
Normally, calling alloc_iova() using an iova_domain with insufficient
pfns remaining between start_pfn and dma_limit will fail and return a
NULL pointer. Unexpectedly, if such a "full" iova_domain contains an
iova with pfn_lo == 0, the alloc_iova() call will instead succeed and
return an iova containing invalid pfns.
This is caused by an underflow bug in __alloc_and_insert_iova_range()
that occurs after walking the "full" iova tree when the search ends
at the iova with pfn_lo == 0 and limit_pfn is then adjusted to be just
below that (-1). This (now huge) limit_pfn gives the impression that a
vast amount of space is available between it and start_pfn and thus
a new iova is allocated with the invalid pfn_hi value, 0xFFF.... .
To rememdy this, a check is introduced to ensure that adjustments to
limit_pfn will not underflow.
This issue has been observed in the wild, and is easily reproduced with
the following sample code.
struct iova_domain *iovad = kzalloc(sizeof(*iovad), GFP_KERNEL);
struct iova *rsvd_iova, *good_iova, *bad_iova;
unsigned long limit_pfn = 3;
unsigned long start_pfn = 1;
unsigned long va_size = 2;
init_iova_domain(iovad, SZ_4K, start_pfn, limit_pfn);
rsvd_iova = reserve_iova(iovad, 0, 0);
good_iova = alloc_iova(iovad, va_size, limit_pfn, true);
bad_iova = alloc_iova(iovad, va_size, limit_pfn, true);
Prior to the patch, this yielded:
*rsvd_iova == {0, 0} /* Expected */
*good_iova == {2, 3} /* Expected */
*bad_iova == {-2, -1} /* Oh no... */
After the patch, bad_iova is NULL as expected since inadequate
space remains between limit_pfn and start_pfn after allocating
good_iova.
Signed-off-by: Nate Watterson <[email protected]>
Signed-off-by: Joerg Roedel <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/iommu/iova.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/iommu/iova.c b/drivers/iommu/iova.c
index e23001bfcfee..f106fd9782bf 100644
--- a/drivers/iommu/iova.c
+++ b/drivers/iommu/iova.c
@@ -138,7 +138,7 @@ static int __alloc_and_insert_iova_range(struct iova_domain *iovad,
break; /* found a free slot */
}
adjust_limit_pfn:
- limit_pfn = curr_iova->pfn_lo - 1;
+ limit_pfn = curr_iova->pfn_lo ? (curr_iova->pfn_lo - 1) : 0;
move_left:
prev = curr;
curr = rb_prev(curr);
--
2.14.1
From: Chen-Yu Tsai <[email protected]>
[ Upstream commit 68f37d862403e8f95337b2eca90af15d0b8cd5d7 ]
The DDR1 PLL on the A33 is an oddball amongst the A33 CCU clocks.
It is a clock multiplier, with the effective multiplier in the
range of 12 ~ 255 and no offset between the multiplier value and
the value programmed into the register.
Implement the zero offset and minimum value of 12 for this clock.
Fixes: d05c748bd730 ("clk: sunxi-ng: Add A33 CCU support")
Signed-off-by: Chen-Yu Tsai <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/clk/sunxi-ng/ccu-sun8i-a33.c | 18 +++++++++++-------
1 file changed, 11 insertions(+), 7 deletions(-)
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-a33.c b/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
index e1dc4e5b34e1..bdbaf26f551f 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
@@ -159,13 +159,17 @@ static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_de_clk, "pll-de",
BIT(28), /* lock */
CLK_SET_RATE_UNGATE);
-/* TODO: Fix N */
-static SUNXI_CCU_N_WITH_GATE_LOCK(pll_ddr1_clk, "pll-ddr1",
- "osc24M", 0x04c,
- 8, 6, /* N */
- BIT(31), /* gate */
- BIT(28), /* lock */
- CLK_SET_RATE_UNGATE);
+static struct ccu_mult pll_ddr1_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .mult = _SUNXI_CCU_MULT_OFFSET_MIN_MAX(8, 6, 0, 12, 0),
+ .common = {
+ .reg = 0x04c,
+ .hw.init = CLK_HW_INIT("pll-ddr1", "osc24M",
+ &ccu_mult_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
static const char * const cpux_parents[] = { "osc32k", "osc24M",
"pll-cpux" , "pll-cpux" };
--
2.14.1
From: Mauricio Faria de Oliveira <[email protected]>
[ Upstream commit 75106523f39751390b5789b36ee1d213b3af1945 ]
The commit 08024885a2a3 ("ses: Add power_status to SES device slot")
introduced the 'power_status' attribute to enclosure components and
the associated callbacks.
There are 2 callbacks available to get the power status of a device:
1) ses_get_power_status() for 'struct enclosure_component_callbacks'
2) get_component_power_status() for the sysfs device attribute
(these are available for kernel-space and user-space, respectively.)
However, despite both methods being available to get power status
on demand, that commit also introduced a call to get power status
in ses_enclosure_data_process().
This dramatically increased the total probe time for SCSI devices
on larger configurations, because ses_enclosure_data_process() is
called several times during the SCSI devices probe and loops over
the component devices (but that is another problem, another patch).
That results in a tremendous continuous hammering of SCSI Receive
Diagnostics commands to the enclosure-services device, which does
delay the total probe time for the SCSI devices __significantly__:
Originally, ~34 minutes on a system attached to ~170 disks:
[ 9214.490703] mpt3sas version 13.100.00.00 loaded
...
[11256.580231] scsi 17:0:177:0: qdepth(16), tagged(1), simple(0),
ordered(0), scsi_level(6), cmd_que(1)
With this patch, it decreased to ~2.5 minutes -- a 13.6x faster
[ 1002.992533] mpt3sas version 13.100.00.00 loaded
...
[ 1151.978831] scsi 11:0:177:0: qdepth(16), tagged(1), simple(0),
ordered(0), scsi_level(6), cmd_que(1)
Back to the commit discussion.. on the ses_get_power_status() call
introduced in ses_enclosure_data_process(): impact of removing it.
That may possibly be in place to initialize the power status value
on device probe. However, those 2 functions available to retrieve
that value _do_ automatically refresh/update it. So the potential
benefit would be a direct access of the 'power_status' field which
does not use the callbacks...
But the only reader of 'struct enclosure_component::power_status'
is the get_component_power_status() callback for sysfs attribute,
and it _does_ check for and call the .get_power_status callback,
(which indeed is defined and implemented by that commit), so the
power status value is, again, automatically updated.
So, the remaining potential for a direct/non-callback access to
the power_status attribute would be out-of-tree modules -- well,
for those, if they are for whatever reason interested in values
that are set during device probe and not up-to-date by the time
they need it.. well, that would be curious.
Well, to handle that more properly, set the initial power state
value to '-1' (i.e., uninitialized) instead of '1' (power 'on'),
and check for it in that callback which may do an direct access
to the field value _if_ a callback function is not defined.
Signed-off-by: Mauricio Faria de Oliveira <[email protected]>
Fixes: 08024885a2a3 ("ses: Add power_status to SES device slot")
Reviewed-by: Dan Williams <[email protected]>
Reviewed-by: Song Liu <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/misc/enclosure.c | 7 ++++++-
drivers/scsi/ses.c | 1 -
2 files changed, 6 insertions(+), 2 deletions(-)
diff --git a/drivers/misc/enclosure.c b/drivers/misc/enclosure.c
index cc91f7b3d90c..eb29113e0bac 100644
--- a/drivers/misc/enclosure.c
+++ b/drivers/misc/enclosure.c
@@ -148,7 +148,7 @@ enclosure_register(struct device *dev, const char *name, int components,
for (i = 0; i < components; i++) {
edev->component[i].number = -1;
edev->component[i].slot = -1;
- edev->component[i].power_status = 1;
+ edev->component[i].power_status = -1;
}
mutex_lock(&container_list_lock);
@@ -600,6 +600,11 @@ static ssize_t get_component_power_status(struct device *cdev,
if (edev->cb->get_power_status)
edev->cb->get_power_status(edev, ecomp);
+
+ /* If still uninitialized, the callback failed or does not exist. */
+ if (ecomp->power_status == -1)
+ return (edev->cb->get_power_status) ? -EIO : -ENOTTY;
+
return snprintf(buf, 40, "%s\n", ecomp->power_status ? "on" : "off");
}
diff --git a/drivers/scsi/ses.c b/drivers/scsi/ses.c
index 50adabbb5808..f1cdf32d7514 100644
--- a/drivers/scsi/ses.c
+++ b/drivers/scsi/ses.c
@@ -548,7 +548,6 @@ static void ses_enclosure_data_process(struct enclosure_device *edev,
ecomp = &edev->component[components++];
if (!IS_ERR(ecomp)) {
- ses_get_power_status(edev, ecomp);
if (addl_desc_ptr)
ses_process_descriptor(
ecomp,
--
2.14.1
From: Javier Martinez Canillas <[email protected]>
[ Upstream commit 5cf015d9cb02c360582b624497b0a1716881cf28 ]
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-wm8978.ko | grep alias
alias: i2c:wm8978
After this patch:
$ modinfo sound/soc/codecs/snd-soc-wm8978.ko | grep alias
alias: i2c:wm8978
alias: of:N*T*Cwlf,wm8978C*
alias: of:N*T*Cwlf,wm8978
Signed-off-by: Javier Martinez Canillas <[email protected]>
Acked-by: Charles Keepax <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
sound/soc/codecs/wm8978.c | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/sound/soc/codecs/wm8978.c b/sound/soc/codecs/wm8978.c
index 90b2d418ef60..cf761e2d7546 100644
--- a/sound/soc/codecs/wm8978.c
+++ b/sound/soc/codecs/wm8978.c
@@ -1071,9 +1071,16 @@ static const struct i2c_device_id wm8978_i2c_id[] = {
};
MODULE_DEVICE_TABLE(i2c, wm8978_i2c_id);
+static const struct of_device_id wm8978_of_match[] = {
+ { .compatible = "wlf,wm8978", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, wm8978_of_match);
+
static struct i2c_driver wm8978_i2c_driver = {
.driver = {
.name = "wm8978",
+ .of_match_table = wm8978_of_match,
},
.probe = wm8978_i2c_probe,
.remove = wm8978_i2c_remove,
--
2.14.1
From: Easwar Hariharan <[email protected]>
[ Upstream commit fb897ad315643e5dc1092a115b3cec914b66df9d ]
Attempting to read the status of a QSFP cable creates noise in the logs
and misses out on setting an appropriate Offline/Disabled Reason if the
cable is not plugged in. Check for this prior to attempting the read and
attendant retries.
Fixes: 673b975f1fba ("IB/hfi1: Add QSFP sanity pre-check")
Reviewed-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Easwar Hariharan <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/infiniband/hw/hfi1/chip.c | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/drivers/infiniband/hw/hfi1/chip.c b/drivers/infiniband/hw/hfi1/chip.c
index 4682909b021b..3be62ef154d1 100644
--- a/drivers/infiniband/hw/hfi1/chip.c
+++ b/drivers/infiniband/hw/hfi1/chip.c
@@ -9489,8 +9489,11 @@ static int test_qsfp_read(struct hfi1_pportdata *ppd)
int ret;
u8 status;
- /* report success if not a QSFP */
- if (ppd->port_type != PORT_TYPE_QSFP)
+ /*
+ * Report success if not a QSFP or, if it is a QSFP, but the cable is
+ * not present
+ */
+ if (ppd->port_type != PORT_TYPE_QSFP || !qsfp_mod_present(ppd))
return 0;
/* read byte 2, the status byte */
--
2.14.1
From: Geert Uytterhoeven <[email protected]>
[ Upstream commit ebf06af55c7594ed1fc18469a5cddf911c40e687 ]
The X2 crystal oscillator on the Koelsch development board provides a
74.25 MHz clock, not a 148.5 MHz clock.
Fixes: cd21cb46e14aae3a ("ARM: shmobile: koelsch: Add DU external pixel clocks to DT")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Acked-by: Laurent Pinchart <[email protected]>
Tested-by: Niklas Söderlund <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/r8a7791-koelsch.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index f8a7d090fd01..12841e9bab98 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -279,7 +279,7 @@
x2_clk: x2-clock {
compatible = "fixed-clock";
#clock-cells = <0>;
- clock-frequency = <148500000>;
+ clock-frequency = <74250000>;
};
x13_clk: x13-clock {
--
2.14.1
From: Chris Brandt <[email protected]>
[ Upstream commit 91a7c50cb4fabfba218549dfa84356069918bfbf ]
Technically, the Ethernet block is run off the 133MHz Bus (B) clock, not
the 33MHz Peripheral 0 (P0) clock.
Fixes: 969244f9c720 ("ARM: dts: r7s72100: add ethernet clock to device tree")
Signed-off-by: Chris Brandt <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/r7s72100.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/r7s72100.dtsi b/arch/arm/boot/dts/r7s72100.dtsi
index fb9ef9ca120e..959e3edf367b 100644
--- a/arch/arm/boot/dts/r7s72100.dtsi
+++ b/arch/arm/boot/dts/r7s72100.dtsi
@@ -112,7 +112,7 @@
#clock-cells = <1>;
compatible = "renesas,r7s72100-mstp-clocks", "renesas,cpg-mstp-clocks";
reg = <0xfcfe0430 4>;
- clocks = <&p0_clk>;
+ clocks = <&b_clk>;
clock-indices = <R7S72100_CLK_ETHER>;
clock-output-names = "ether";
};
--
2.14.1
From: Javier Martinez Canillas <[email protected]>
[ Upstream commit 71c314d7ef2442cd798584a3dece8151215e1777 ]
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-ssm4567.ko | grep alias
alias: acpi*:INT343B:*
alias: i2c:ssm4567
After this patch:
$ modinfo sound/soc/codecs/snd-soc-ssm4567.ko | grep alias
alias: acpi*:INT343B:*
alias: of:N*T*Cadi,ssm4567C*
alias: of:N*T*Cadi,ssm4567
alias: i2c:ssm4567
Signed-off-by: Javier Martinez Canillas <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
sound/soc/codecs/ssm4567.c | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/sound/soc/codecs/ssm4567.c b/sound/soc/codecs/ssm4567.c
index 2bb5a11c9ba1..a622623e8558 100644
--- a/sound/soc/codecs/ssm4567.c
+++ b/sound/soc/codecs/ssm4567.c
@@ -485,6 +485,14 @@ static const struct i2c_device_id ssm4567_i2c_ids[] = {
};
MODULE_DEVICE_TABLE(i2c, ssm4567_i2c_ids);
+#ifdef CONFIG_OF
+static const struct of_device_id ssm4567_of_match[] = {
+ { .compatible = "adi,ssm4567", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, ssm4567_of_match);
+#endif
+
#ifdef CONFIG_ACPI
static const struct acpi_device_id ssm4567_acpi_match[] = {
@@ -498,6 +506,7 @@ MODULE_DEVICE_TABLE(acpi, ssm4567_acpi_match);
static struct i2c_driver ssm4567_driver = {
.driver = {
.name = "ssm4567",
+ .of_match_table = of_match_ptr(ssm4567_of_match),
.acpi_match_table = ACPI_PTR(ssm4567_acpi_match),
},
.probe = ssm4567_i2c_probe,
--
2.14.1
From: Javier Martinez Canillas <[email protected]>
[ Upstream commit 9ba2da5f5d18daaa365ab5426b05e16f1d114786 ]
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-rt5645.ko | grep alias
alias: acpi*:10EC3270:*
alias: acpi*:10EC5640:*
alias: acpi*:10EC5650:*
alias: acpi*:10EC5648:*
alias: acpi*:10EC5645:*
alias: i2c:rt5650
alias: i2c:rt5645
After this patch:
$ modinfo sound/soc/codecs/snd-soc-rt5645.ko | grep alias
alias: of:N*T*Crealtek,rt5650C*
alias: of:N*T*Crealtek,rt5650
alias: of:N*T*Crealtek,rt5645C*
alias: of:N*T*Crealtek,rt5645
alias: acpi*:10EC3270:*
alias: acpi*:10EC5640:*
alias: acpi*:10EC5650:*
alias: acpi*:10EC5648:*
alias: acpi*:10EC5645:*
alias: i2c:rt5650
alias: i2c:rt5645
Signed-off-by: Javier Martinez Canillas <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
sound/soc/codecs/rt5645.c | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/sound/soc/codecs/rt5645.c b/sound/soc/codecs/rt5645.c
index 1ac96ef9ee20..959d53725cbd 100644
--- a/sound/soc/codecs/rt5645.c
+++ b/sound/soc/codecs/rt5645.c
@@ -3542,6 +3542,15 @@ static const struct i2c_device_id rt5645_i2c_id[] = {
};
MODULE_DEVICE_TABLE(i2c, rt5645_i2c_id);
+#ifdef CONFIG_OF
+static const struct of_device_id rt5645_of_match[] = {
+ { .compatible = "realtek,rt5645", },
+ { .compatible = "realtek,rt5650", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, rt5645_of_match);
+#endif
+
#ifdef CONFIG_ACPI
static const struct acpi_device_id rt5645_acpi_match[] = {
{ "10EC5645", 0 },
@@ -3904,6 +3913,7 @@ static void rt5645_i2c_shutdown(struct i2c_client *i2c)
static struct i2c_driver rt5645_i2c_driver = {
.driver = {
.name = "rt5645",
+ .of_match_table = of_match_ptr(rt5645_of_match),
.acpi_match_table = ACPI_PTR(rt5645_acpi_match),
},
.probe = rt5645_i2c_probe,
--
2.14.1
From: Arnd Bergmann <[email protected]>
[ Upstream commit bd737038d555468198495230f4233b9ba92e774c ]
With the new Tegra186 PMC driver merged, anything that relies on the previous
PMC driver fails to link when that is disabled:
arch/arm/mach-tegra/pm.o: In function `tegra_pm_set':
pm.c:(.text.tegra_pm_set+0x3c): undefined reference to `tegra_pmc_enter_suspend_mode'
arch/arm/mach-tegra/pm.o: In function `tegra_suspend_enter':
pm.c:(.text.tegra_suspend_enter+0x4): undefined reference to `tegra_pmc_get_suspend_mode'
arch/arm/mach-tegra/pm.o: In function `tegra_init_suspend':
pm.c:(.init.text+0x1c): undefined reference to `tegra_pmc_get_suspend_mode'
pm.c:(.init.text+0x74): undefined reference to `tegra_pmc_set_suspend_mode'
ERROR: tegra_powergate_sequence_power_up [drivers/ata/ahci_tegra.ko] undefined!
ERROR: tegra_powergate_power_off [drivers/ata/ahci_tegra.ko] undefined!
Making the definition depend on the presence of the driver makes it build
again, though that might not be the correct fix.
Reported-by: Krzysztof Kozlowski <[email protected]>
Fixes: 854014236290 ("soc/tegra: Implement Tegra186 PMC support")
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
include/soc/tegra/pmc.h | 29 +++++++++++++++++++++--------
1 file changed, 21 insertions(+), 8 deletions(-)
diff --git a/include/soc/tegra/pmc.h b/include/soc/tegra/pmc.h
index e9e53473a63e..6d2fe5045b13 100644
--- a/include/soc/tegra/pmc.h
+++ b/include/soc/tegra/pmc.h
@@ -26,12 +26,6 @@
struct clk;
struct reset_control;
-#ifdef CONFIG_PM_SLEEP
-enum tegra_suspend_mode tegra_pmc_get_suspend_mode(void);
-void tegra_pmc_set_suspend_mode(enum tegra_suspend_mode mode);
-void tegra_pmc_enter_suspend_mode(enum tegra_suspend_mode mode);
-#endif /* CONFIG_PM_SLEEP */
-
#ifdef CONFIG_SMP
bool tegra_pmc_cpu_is_powered(unsigned int cpuid);
int tegra_pmc_cpu_power_on(unsigned int cpuid);
@@ -108,7 +102,7 @@ int tegra_pmc_cpu_remove_clamping(unsigned int cpuid);
#define TEGRA_IO_RAIL_LVDS 57
#define TEGRA_IO_RAIL_SYS_DDC 58
-#ifdef CONFIG_ARCH_TEGRA
+#ifdef CONFIG_SOC_TEGRA_PMC
int tegra_powergate_is_powered(unsigned int id);
int tegra_powergate_power_on(unsigned int id);
int tegra_powergate_power_off(unsigned int id);
@@ -120,6 +114,11 @@ int tegra_powergate_sequence_power_up(unsigned int id, struct clk *clk,
int tegra_io_rail_power_on(unsigned int id);
int tegra_io_rail_power_off(unsigned int id);
+
+enum tegra_suspend_mode tegra_pmc_get_suspend_mode(void);
+void tegra_pmc_set_suspend_mode(enum tegra_suspend_mode mode);
+void tegra_pmc_enter_suspend_mode(enum tegra_suspend_mode mode);
+
#else
static inline int tegra_powergate_is_powered(unsigned int id)
{
@@ -157,6 +156,20 @@ static inline int tegra_io_rail_power_off(unsigned int id)
{
return -ENOSYS;
}
-#endif /* CONFIG_ARCH_TEGRA */
+
+static inline enum tegra_suspend_mode tegra_pmc_get_suspend_mode(void)
+{
+ return TEGRA_SUSPEND_NONE;
+}
+
+static inline void tegra_pmc_set_suspend_mode(enum tegra_suspend_mode mode)
+{
+}
+
+static inline void tegra_pmc_enter_suspend_mode(enum tegra_suspend_mode mode)
+{
+}
+
+#endif /* CONFIG_SOC_TEGRA_PMC */
#endif /* __SOC_TEGRA_PMC_H__ */
--
2.14.1
From: Javier Martinez Canillas <[email protected]>
[ Upstream commit 7b87463edf3e2c16d72eeea3d1cf3c12bb5487c6 ]
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-rt5677.ko | grep alias
alias: i2c:RT5677CE:00
alias: i2c:rt5676
alias: i2c:rt5677
After this patch:
$ modinfo sound/soc/codecs/snd-soc-rt5677.ko | grep alias
alias: of:N*T*Crealtek,rt5677C*
alias: of:N*T*Crealtek,rt5677
alias: i2c:RT5677CE:00
alias: i2c:rt5676
alias: i2c:rt5677
Signed-off-by: Javier Martinez Canillas <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
sound/soc/codecs/rt5677.c | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/sound/soc/codecs/rt5677.c b/sound/soc/codecs/rt5677.c
index abc802a5a479..65ac4518ad06 100644
--- a/sound/soc/codecs/rt5677.c
+++ b/sound/soc/codecs/rt5677.c
@@ -5035,6 +5035,12 @@ static const struct i2c_device_id rt5677_i2c_id[] = {
};
MODULE_DEVICE_TABLE(i2c, rt5677_i2c_id);
+static const struct of_device_id rt5677_of_match[] = {
+ { .compatible = "realtek,rt5677", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, rt5677_of_match);
+
static const struct acpi_gpio_params plug_det_gpio = { RT5677_GPIO_PLUG_DET, 0, false };
static const struct acpi_gpio_params mic_present_gpio = { RT5677_GPIO_MIC_PRESENT_L, 0, false };
static const struct acpi_gpio_params headphone_enable_gpio = { RT5677_GPIO_HP_AMP_SHDN_L, 0, false };
@@ -5294,6 +5300,7 @@ static int rt5677_i2c_remove(struct i2c_client *i2c)
static struct i2c_driver rt5677_i2c_driver = {
.driver = {
.name = "rt5677",
+ .of_match_table = rt5677_of_match,
},
.probe = rt5677_i2c_probe,
.remove = rt5677_i2c_remove,
--
2.14.1
From: Geert Uytterhoeven <[email protected]>
[ Upstream commit 1cd9028027c7a7c10b774df698c3cfafec6aa67d ]
The SSI-ALL gate clock is located in between the P clock and the
individual SSI[0-9] clocks, hence the former should be listed as their
parent.
Fixes: 072d326542e49187 ("ARM: dts: r8a7793: add MSTP10 clocks to device tree")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/r8a7793.dtsi | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index bd7ee309f509..e9625cb3bbaa 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -1234,8 +1234,11 @@
compatible = "renesas,r8a7793-mstp-clocks", "renesas,cpg-mstp-clocks";
reg = <0 0xe6150998 0 4>, <0 0xe61509a8 0 4>;
clocks = <&p_clk>,
- <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>,
- <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>,
+ <&mstp10_clks R8A7793_CLK_SSI_ALL>, <&mstp10_clks R8A7793_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7793_CLK_SSI_ALL>, <&mstp10_clks R8A7793_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7793_CLK_SSI_ALL>, <&mstp10_clks R8A7793_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7793_CLK_SSI_ALL>, <&mstp10_clks R8A7793_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7793_CLK_SSI_ALL>, <&mstp10_clks R8A7793_CLK_SSI_ALL>,
<&p_clk>,
<&mstp10_clks R8A7793_CLK_SCU_ALL>, <&mstp10_clks R8A7793_CLK_SCU_ALL>,
<&mstp10_clks R8A7793_CLK_SCU_ALL>, <&mstp10_clks R8A7793_CLK_SCU_ALL>,
--
2.14.1
From: Laurent Pinchart <[email protected]>
[ Upstream commit 6dd47cfd03a058d08b8caffb06194aa0eb109cf1 ]
The driver currently handles vblank events only when updating planes on
a CRTC. The atomic update API however allows requesting an event when
disabling a CRTC. This currently leads to event objects being leaked in
the kernel and to events not being sent out. Fix it.
Signed-off-by: Laurent Pinchart <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/gpu/drm/rcar-du/rcar_du_crtc.c | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
index 3322b157106d..1c4d95dea887 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
+++ b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
@@ -512,6 +512,13 @@ static void rcar_du_crtc_disable(struct drm_crtc *crtc)
rcar_du_crtc_stop(rcrtc);
rcar_du_crtc_put(rcrtc);
+ spin_lock_irq(&crtc->dev->event_lock);
+ if (crtc->state->event) {
+ drm_crtc_send_vblank_event(crtc, crtc->state->event);
+ crtc->state->event = NULL;
+ }
+ spin_unlock_irq(&crtc->dev->event_lock);
+
rcrtc->outputs = 0;
}
--
2.14.1
From: Geert Uytterhoeven <[email protected]>
[ Upstream commit d13d4e063d4a08eb1686e890e9183dde709871bf ]
The SSI-ALL gate clock is located in between the P clock and the
individual SSI[0-9] clocks, hence the former should be listed as their
parent.
Fixes: bcde372254386872 ("ARM: shmobile: r8a7790: add MSTP10 support on DTSI")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/r8a7790.dtsi | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index b6c6410ca384..262a51205aee 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -1437,8 +1437,11 @@
compatible = "renesas,r8a7790-mstp-clocks", "renesas,cpg-mstp-clocks";
reg = <0 0xe6150998 0 4>, <0 0xe61509a8 0 4>;
clocks = <&p_clk>,
- <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>,
- <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>,
+ <&mstp10_clks R8A7790_CLK_SSI_ALL>, <&mstp10_clks R8A7790_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7790_CLK_SSI_ALL>, <&mstp10_clks R8A7790_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7790_CLK_SSI_ALL>, <&mstp10_clks R8A7790_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7790_CLK_SSI_ALL>, <&mstp10_clks R8A7790_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7790_CLK_SSI_ALL>, <&mstp10_clks R8A7790_CLK_SSI_ALL>,
<&p_clk>,
<&mstp10_clks R8A7790_CLK_SCU_ALL>, <&mstp10_clks R8A7790_CLK_SCU_ALL>,
<&mstp10_clks R8A7790_CLK_SCU_ALL>, <&mstp10_clks R8A7790_CLK_SCU_ALL>,
--
2.14.1
From: Tobias Klauser <[email protected]>
[ Upstream commit d916d923724d59cde99ee588f15eec59dd863bbd ]
Including linux/unaligned/access_ok.h causes the allmodconfig build on
ia64 (and maybe others) to fail with the following warnings:
include/linux/unaligned/access_ok.h:7:19: error: redefinition of 'get_unaligned_le16'
include/linux/unaligned/access_ok.h:12:19: error: redefinition of 'get_unaligned_le32'
include/linux/unaligned/access_ok.h:17:19: error: redefinition of 'get_unaligned_le64'
include/linux/unaligned/access_ok.h:22:19: error: redefinition of 'get_unaligned_be16'
include/linux/unaligned/access_ok.h:27:19: error: redefinition of 'get_unaligned_be32'
include/linux/unaligned/access_ok.h:32:19: error: redefinition of 'get_unaligned_be64'
include/linux/unaligned/access_ok.h:37:20: error: redefinition of 'put_unaligned_le16'
include/linux/unaligned/access_ok.h:42:20: error: redefinition of 'put_unaligned_le32'
include/linux/unaligned/access_ok.h:42:20: error: redefinition of 'put_unaligned_le64'
include/linux/unaligned/access_ok.h:42:20: error: redefinition of 'put_unaligned_be16'
include/linux/unaligned/access_ok.h:42:20: error: redefinition of 'put_unaligned_be32'
include/linux/unaligned/access_ok.h:42:20: error: redefinition of 'put_unaligned_be64'
Fix these by including asm/unaligned.h instead and leave it up to the
architecture to decide how to implement unaligned accesses.
Fixes: 3194c6870158 ("NFC: nfcmrvl: add firmware download support")
Reported-by: kbuild test robot <[email protected]>
Link: https://lkml.org/lkml/2016/10/22/247
Cc: Vincent Cuissard <[email protected]>
Signed-off-by: Tobias Klauser <[email protected]>
Signed-off-by: Samuel Ortiz <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/nfc/nfcmrvl/fw_dnld.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/nfc/nfcmrvl/fw_dnld.c b/drivers/nfc/nfcmrvl/fw_dnld.c
index af62c4c854f3..b4f31dad40d6 100644
--- a/drivers/nfc/nfcmrvl/fw_dnld.c
+++ b/drivers/nfc/nfcmrvl/fw_dnld.c
@@ -17,7 +17,7 @@
*/
#include <linux/module.h>
-#include <linux/unaligned/access_ok.h>
+#include <asm/unaligned.h>
#include <linux/firmware.h>
#include <linux/nfc.h>
#include <net/nfc/nci.h>
--
2.14.1
From: Michal Kalderon <[email protected]>
[ Upstream commit 44531ba45dbf3c23cc7ae0934ec9b33ef340ac56 ]
When configuring the HW timers block we should set the number of CIDs
up until the last CID that require timers, instead of only those CIDs
whose protocol needs timers support.
Today, the protocols that require HW timers' support have their CIDs
before any other protocol, but that would change in future [when we
add iWARP support].
Signed-off-by: Michal Kalderon <[email protected]>
Signed-off-by: Yuval Mintz <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/qlogic/qed/qed_cxt.c | 32 ++++++++++++++++++++++++-------
1 file changed, 25 insertions(+), 7 deletions(-)
diff --git a/drivers/net/ethernet/qlogic/qed/qed_cxt.c b/drivers/net/ethernet/qlogic/qed/qed_cxt.c
index ed014bdbbabd..457e30427535 100644
--- a/drivers/net/ethernet/qlogic/qed/qed_cxt.c
+++ b/drivers/net/ethernet/qlogic/qed/qed_cxt.c
@@ -271,16 +271,34 @@ struct qed_tm_iids {
u32 per_vf_tids;
};
-static void qed_cxt_tm_iids(struct qed_cxt_mngr *p_mngr,
+static void qed_cxt_tm_iids(struct qed_hwfn *p_hwfn,
+ struct qed_cxt_mngr *p_mngr,
struct qed_tm_iids *iids)
{
- u32 i, j;
-
- for (i = 0; i < MAX_CONN_TYPES; i++) {
+ bool tm_vf_required = false;
+ bool tm_required = false;
+ int i, j;
+
+ /* Timers is a special case -> we don't count how many cids require
+ * timers but what's the max cid that will be used by the timer block.
+ * therefore we traverse in reverse order, and once we hit a protocol
+ * that requires the timers memory, we'll sum all the protocols up
+ * to that one.
+ */
+ for (i = MAX_CONN_TYPES - 1; i >= 0; i--) {
struct qed_conn_type_cfg *p_cfg = &p_mngr->conn_cfg[i];
- if (tm_cid_proto(i)) {
+ if (tm_cid_proto(i) || tm_required) {
+ if (p_cfg->cid_count)
+ tm_required = true;
+
iids->pf_cids += p_cfg->cid_count;
+ }
+
+ if (tm_cid_proto(i) || tm_vf_required) {
+ if (p_cfg->cids_per_vf)
+ tm_vf_required = true;
+
iids->per_vf_cids += p_cfg->cids_per_vf;
}
}
@@ -696,7 +714,7 @@ int qed_cxt_cfg_ilt_compute(struct qed_hwfn *p_hwfn)
/* TM PF */
p_cli = &p_mngr->clients[ILT_CLI_TM];
- qed_cxt_tm_iids(p_mngr, &tm_iids);
+ qed_cxt_tm_iids(p_hwfn, p_mngr, &tm_iids);
total = tm_iids.pf_cids + tm_iids.pf_tids_total;
if (total) {
p_blk = &p_cli->pf_blks[0];
@@ -1591,7 +1609,7 @@ static void qed_tm_init_pf(struct qed_hwfn *p_hwfn)
u8 i;
memset(&tm_iids, 0, sizeof(tm_iids));
- qed_cxt_tm_iids(p_mngr, &tm_iids);
+ qed_cxt_tm_iids(p_hwfn, p_mngr, &tm_iids);
/* @@@TBD No pre-scan for now */
--
2.14.1
From: Peter Zijlstra <[email protected]>
[ Upstream commit e0aad5b44ff5d28ac1d6ae70cdf84ca228e889dc ]
rt_mutex_waiter::prio is a copy of task_struct::prio which is updated
during the PI chain walk, such that the PI chain order isn't messed up
by (asynchronous) task state updates.
Currently rt_mutex_waiter_less() uses task state for deadline tasks;
this is broken, since the task state can, as said above, change
asynchronously, causing the RB tree order to change without actual
tree update -> FAIL.
Fix this by also copying the deadline into the rt_mutex_waiter state
and updating it along with its prio field.
Ideally we would also force PI chain updates whenever DL tasks update
their deadline parameter, but for first approximation this is less
broken than it was.
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
kernel/locking/rtmutex.c | 29 +++++++++++++++++++++++++++--
kernel/locking/rtmutex_common.h | 1 +
2 files changed, 28 insertions(+), 2 deletions(-)
diff --git a/kernel/locking/rtmutex.c b/kernel/locking/rtmutex.c
index 2c49d76f96c3..196cc460e38d 100644
--- a/kernel/locking/rtmutex.c
+++ b/kernel/locking/rtmutex.c
@@ -236,8 +236,7 @@ rt_mutex_waiter_less(struct rt_mutex_waiter *left,
* then right waiter has a dl_prio() too.
*/
if (dl_prio(left->prio))
- return dl_time_before(left->task->dl.deadline,
- right->task->dl.deadline);
+ return dl_time_before(left->deadline, right->deadline);
return 0;
}
@@ -704,7 +703,26 @@ static int rt_mutex_adjust_prio_chain(struct task_struct *task,
/* [7] Requeue the waiter in the lock waiter tree. */
rt_mutex_dequeue(lock, waiter);
+
+ /*
+ * Update the waiter prio fields now that we're dequeued.
+ *
+ * These values can have changed through either:
+ *
+ * sys_sched_set_scheduler() / sys_sched_setattr()
+ *
+ * or
+ *
+ * DL CBS enforcement advancing the effective deadline.
+ *
+ * Even though pi_waiters also uses these fields, and that tree is only
+ * updated in [11], we can do this here, since we hold [L], which
+ * serializes all pi_waiters access and rb_erase() does not care about
+ * the values of the node being removed.
+ */
waiter->prio = task->prio;
+ waiter->deadline = task->dl.deadline;
+
rt_mutex_enqueue(lock, waiter);
/* [8] Release the task */
@@ -831,6 +849,8 @@ static int rt_mutex_adjust_prio_chain(struct task_struct *task,
static int try_to_take_rt_mutex(struct rt_mutex *lock, struct task_struct *task,
struct rt_mutex_waiter *waiter)
{
+ lockdep_assert_held(&lock->wait_lock);
+
/*
* Before testing whether we can acquire @lock, we set the
* RT_MUTEX_HAS_WAITERS bit in @lock->owner. This forces all
@@ -958,6 +978,8 @@ static int task_blocks_on_rt_mutex(struct rt_mutex *lock,
struct rt_mutex *next_lock;
int chain_walk = 0, res;
+ lockdep_assert_held(&lock->wait_lock);
+
/*
* Early deadlock detection. We really don't want the task to
* enqueue on itself just to untangle the mess later. It's not
@@ -975,6 +997,7 @@ static int task_blocks_on_rt_mutex(struct rt_mutex *lock,
waiter->task = task;
waiter->lock = lock;
waiter->prio = task->prio;
+ waiter->deadline = task->dl.deadline;
/* Get the top priority waiter on the lock */
if (rt_mutex_has_waiters(lock))
@@ -1080,6 +1103,8 @@ static void remove_waiter(struct rt_mutex *lock,
struct task_struct *owner = rt_mutex_owner(lock);
struct rt_mutex *next_lock;
+ lockdep_assert_held(&lock->wait_lock);
+
raw_spin_lock(¤t->pi_lock);
rt_mutex_dequeue(lock, waiter);
current->pi_blocked_on = NULL;
diff --git a/kernel/locking/rtmutex_common.h b/kernel/locking/rtmutex_common.h
index e317e1cbb3eb..50848b460851 100644
--- a/kernel/locking/rtmutex_common.h
+++ b/kernel/locking/rtmutex_common.h
@@ -33,6 +33,7 @@ struct rt_mutex_waiter {
struct rt_mutex *deadlock_lock;
#endif
int prio;
+ u64 deadline;
};
/*
--
2.14.1
From: Petr Mladek <[email protected]>
[ Upstream commit 257ab443118bffc7fdcef38f49cf59be68a3e362 ]
Some console drivers code calls console_conditional_schedule()
that looks at @console_may_schedule. The value must be cleared
when the drivers are called from console_unlock() with
interrupts disabled. But rescheduling is fine when the same
code is called, for example, from tty operations where the
console semaphore is taken via console_lock().
This is why @console_may_schedule is cleared before calling console
drivers. The original value is stored to decide if we could sleep
between lines.
Now, @console_may_schedule is not cleared when we call
console_trylock() and jump back to the "again" goto label.
This has become a problem, since the commit 6b97a20d3a7909daa066
("printk: set may_schedule for some of console_trylock() callers").
@console_may_schedule might get enabled now.
There is also the opposite problem. console_lock() can be called
only from preemptive context. It can always enable scheduling in
the console code. But console_trylock() is not able to detect it
when CONFIG_PREEMPT_COUNT is disabled. Therefore we should use the
original @console_may_schedule value after re-acquiring
the console semaphore in console_unlock().
This patch solves both problems by moving the "again" goto label.
Alternative solution was to clear and restore the value around
call_console_drivers(). Then console_conditional_schedule() could
be used also inside console_unlock(). But there was a potential race
with console_flush_on_panic() as reported by Sergey Senozhatsky.
That function should be called only where there is only one CPU
and with interrupts disabled. But better be on the safe side
because stopping CPUs might fail.
Fixes: 6b97a20d3a7909 ("printk: set may_schedule for some of console_trylock() callers")
Link: http://lkml.kernel.org/r/[email protected]
Suggested-by: Tetsuo Handa <[email protected]>
Cc: Steven Rostedt <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Andrew Morton <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Jiri Slaby <[email protected]>
Cc: [email protected]
Cc: [email protected]
Reviewed-by: Sergey Senozhatsky <[email protected]>
Signed-off-by: Petr Mladek <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
kernel/printk/printk.c | 8 ++++++--
1 file changed, 6 insertions(+), 2 deletions(-)
diff --git a/kernel/printk/printk.c b/kernel/printk/printk.c
index 9c5b231684d0..ab6855a4218b 100644
--- a/kernel/printk/printk.c
+++ b/kernel/printk/printk.c
@@ -2342,7 +2342,7 @@ void console_unlock(void)
}
/*
- * Console drivers are called under logbuf_lock, so
+ * Console drivers are called with interrupts disabled, so
* @console_may_schedule should be cleared before; however, we may
* end up dumping a lot of lines, for example, if called from
* console registration path, and should invoke cond_resched()
@@ -2350,11 +2350,15 @@ void console_unlock(void)
* scheduling stall on a slow console leading to RCU stall and
* softlockup warnings which exacerbate the issue with more
* messages practically incapacitating the system.
+ *
+ * console_trylock() is not able to detect the preemptive
+ * context reliably. Therefore the value must be stored before
+ * and cleared after the the "again" goto label.
*/
do_cond_resched = console_may_schedule;
+again:
console_may_schedule = 0;
-again:
/*
* We released the console_sem lock, so we need to recheck if
* cpu is online and (if not) is there at least one CON_ANYTIME
--
2.14.1
From: Andrey Rusalin <[email protected]>
[ Upstream commit 068a496c4525c638ffab56449d905b88ef97fe32 ]
Change order of free_irq and dev unregistration.
It fixes situation when device already unregistered and
an interrupt happens and nobody can handle it.
Signed-off-by: Andrey Rusalin <[email protected]>
Signed-off-by: Samuel Ortiz <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/nfc/pn533/i2c.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/nfc/pn533/i2c.c b/drivers/nfc/pn533/i2c.c
index 1dc89248e58e..11d78b43cf76 100644
--- a/drivers/nfc/pn533/i2c.c
+++ b/drivers/nfc/pn533/i2c.c
@@ -242,10 +242,10 @@ static int pn533_i2c_remove(struct i2c_client *client)
dev_dbg(&client->dev, "%s\n", __func__);
- pn533_unregister_device(phy->priv);
-
free_irq(client->irq, phy);
+ pn533_unregister_device(phy->priv);
+
return 0;
}
--
2.14.1
From: lipeng <[email protected]>
[ Upstream commit 64ec10dc2ab8ef5bc6e76b1d4bc8203c08a6da1e ]
This patch fixes below ethtool configuration error:
localhost:~ # ethtool -X eth0 hkey XX:XX:XX...
Cannot set Rx flow hash configuration: Operation not supported
Signed-off-by: lipeng <[email protected]>
Reviewed-by: Yisen Zhuang <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c | 23 ++++++++++++++---------
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c | 9 ++++-----
2 files changed, 18 insertions(+), 14 deletions(-)
diff --git a/drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c b/drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c
index 2d0cb609adc3..b7c8433a7a37 100644
--- a/drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c
+++ b/drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c
@@ -773,8 +773,9 @@ static int hns_ae_get_rss(struct hnae_handle *handle, u32 *indir, u8 *key,
memcpy(key, ppe_cb->rss_key, HNS_PPEV2_RSS_KEY_SIZE);
/* update the current hash->queue mappings from the shadow RSS table */
- memcpy(indir, ppe_cb->rss_indir_table,
- HNS_PPEV2_RSS_IND_TBL_SIZE * sizeof(*indir));
+ if (indir)
+ memcpy(indir, ppe_cb->rss_indir_table,
+ HNS_PPEV2_RSS_IND_TBL_SIZE * sizeof(*indir));
return 0;
}
@@ -785,15 +786,19 @@ static int hns_ae_set_rss(struct hnae_handle *handle, const u32 *indir,
struct hns_ppe_cb *ppe_cb = hns_get_ppe_cb(handle);
/* set the RSS Hash Key if specififed by the user */
- if (key)
- hns_ppe_set_rss_key(ppe_cb, (u32 *)key);
+ if (key) {
+ memcpy(ppe_cb->rss_key, key, HNS_PPEV2_RSS_KEY_SIZE);
+ hns_ppe_set_rss_key(ppe_cb, ppe_cb->rss_key);
+ }
- /* update the shadow RSS table with user specified qids */
- memcpy(ppe_cb->rss_indir_table, indir,
- HNS_PPEV2_RSS_IND_TBL_SIZE * sizeof(*indir));
+ if (indir) {
+ /* update the shadow RSS table with user specified qids */
+ memcpy(ppe_cb->rss_indir_table, indir,
+ HNS_PPEV2_RSS_IND_TBL_SIZE * sizeof(*indir));
- /* now update the hardware */
- hns_ppe_set_indir_table(ppe_cb, ppe_cb->rss_indir_table);
+ /* now update the hardware */
+ hns_ppe_set_indir_table(ppe_cb, ppe_cb->rss_indir_table);
+ }
return 0;
}
diff --git a/drivers/net/ethernet/hisilicon/hns/hns_ethtool.c b/drivers/net/ethernet/hisilicon/hns/hns_ethtool.c
index 87d5c94b2810..8490cba230bd 100644
--- a/drivers/net/ethernet/hisilicon/hns/hns_ethtool.c
+++ b/drivers/net/ethernet/hisilicon/hns/hns_ethtool.c
@@ -1243,6 +1243,7 @@ hns_set_rss(struct net_device *netdev, const u32 *indir, const u8 *key,
{
struct hns_nic_priv *priv = netdev_priv(netdev);
struct hnae_ae_ops *ops;
+ int ret;
if (AE_IS_VER1(priv->enet_ver)) {
netdev_err(netdev,
@@ -1252,12 +1253,10 @@ hns_set_rss(struct net_device *netdev, const u32 *indir, const u8 *key,
ops = priv->ae_handle->dev->ops;
- /* currently hfunc can only be Toeplitz hash */
- if (key ||
- (hfunc != ETH_RSS_HASH_NO_CHANGE && hfunc != ETH_RSS_HASH_TOP))
+ if (hfunc != ETH_RSS_HASH_NO_CHANGE && hfunc != ETH_RSS_HASH_TOP) {
+ netdev_err(netdev, "Invalid hfunc!\n");
return -EOPNOTSUPP;
- if (!indir)
- return 0;
+ }
return ops->set_rss(priv->ae_handle, indir, key, hfunc);
}
--
2.14.1
From: Andrew Lunn <[email protected]>
[ Upstream commit d39004ab136ebb6949a7dda9d24376f3d6209295 ]
Breaking the include loop netdevice.h, dsa.h, devlink.h broke this
driver, it depends on includes brought in by these headers. Adding
linux/of.h fixes it.
Fixes: ed0e39e97d34 ("net: break include loop netdevice.h, dsa.h, devlink.h")
Signed-off-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/faraday/ftgmac100.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c
index 262587240c86..0437149f5939 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.c
+++ b/drivers/net/ethernet/faraday/ftgmac100.c
@@ -28,6 +28,7 @@
#include <linux/io.h>
#include <linux/module.h>
#include <linux/netdevice.h>
+#include <linux/of.h>
#include <linux/phy.h>
#include <linux/platform_device.h>
#include <net/ip.h>
--
2.14.1
From: Anton Blanchard <[email protected]>
[ Upstream commit a7a9dcd882a67b68568868b988289fce5ffd8419 ]
Early on in do_page_fault() we call store_updates_sp(), regardless of
the type of exception. For an instruction miss this doesn't make
sense, because we only use this information to detect if a data miss
is the result of a stack expansion instruction or not.
Worse still, it results in a data miss within every userspace
instruction miss handler, because we try and load the very instruction
we are about to install a pte for!
A simple exec microbenchmark runs 6% faster on POWER8 with this fix:
#include <stdlib.h>
#include <stdio.h>
#include <unistd.h>
int main(int argc, char *argv[])
{
unsigned long left = atol(argv[1]);
char leftstr[16];
if (left-- == 0)
return 0;
sprintf(leftstr, "%ld", left);
execlp(argv[0], argv[0], leftstr, NULL);
perror("exec failed\n");
return 0;
}
Pass the number of iterations on the command line (eg 10000) and time
how long it takes to execute.
Signed-off-by: Anton Blanchard <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/powerpc/mm/fault.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/powerpc/mm/fault.c b/arch/powerpc/mm/fault.c
index d0b137d96df1..9376e8e53bfa 100644
--- a/arch/powerpc/mm/fault.c
+++ b/arch/powerpc/mm/fault.c
@@ -294,7 +294,7 @@ int do_page_fault(struct pt_regs *regs, unsigned long address,
* can result in fault, which will cause a deadlock when called with
* mmap_sem held
*/
- if (user_mode(regs))
+ if (!is_exec && user_mode(regs))
store_update_sp = store_updates_sp(regs);
if (user_mode(regs))
--
2.14.1
From: Sinclair Yeh <[email protected]>
[ Upstream commit aa74f0687cfe998e59b20d6454f45e8aa4403c45 ]
1. When unsetting a mode, num_connector should be set to zero
2. The pixel_format field needs to be initialized as newer DRM internal
functions checks this field
3. Take the drm_modeset_lock_all() because vmw_fb_kms_detach() can
change current mode
Signed-off-by: Sinclair Yeh <[email protected]>
Reviewed-by: Thomas Hellstrom <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/gpu/drm/vmwgfx/vmwgfx_fb.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vmwgfx/vmwgfx_fb.c b/drivers/gpu/drm/vmwgfx/vmwgfx_fb.c
index d2d93959b119..aec6e9eef489 100644
--- a/drivers/gpu/drm/vmwgfx/vmwgfx_fb.c
+++ b/drivers/gpu/drm/vmwgfx/vmwgfx_fb.c
@@ -433,7 +433,7 @@ static int vmw_fb_kms_detach(struct vmw_fb_par *par,
set.y = 0;
set.mode = NULL;
set.fb = NULL;
- set.num_connectors = 1;
+ set.num_connectors = 0;
set.connectors = &par->con;
ret = drm_mode_set_config_internal(&set);
if (ret) {
@@ -821,7 +821,9 @@ int vmw_fb_off(struct vmw_private *vmw_priv)
flush_delayed_work(&par->local_work);
mutex_lock(&par->bo_mutex);
+ drm_modeset_lock_all(vmw_priv->dev);
(void) vmw_fb_kms_detach(par, true, false);
+ drm_modeset_unlock_all(vmw_priv->dev);
mutex_unlock(&par->bo_mutex);
return 0;
--
2.14.1
From: Felix Manlunas <[email protected]>
[ Upstream commit d6acfeb17d030bb3907e77c048b0e7783ad8e5a9 ]
vxlan dev currently ignores lowerdev's gso_max_size, which adversely
affects TSO performance of liquidio if it's the lowerdev. Egress TCP
packets' skb->len often exceed liquidio's advertised gso_max_size. This
may happen on other NIC drivers.
Fix it by assigning lowerdev's gso_max_size to that of vxlan dev. Might as
well do likewise for gso_max_segs.
Single flow TSO throughput of liquidio as lowerdev (using iperf3):
Before the patch: 139 Mbps
After the patch : 8.68 Gbps
Percent increase: 6,144 %
Signed-off-by: Felix Manlunas <[email protected]>
Signed-off-by: Satanand Burla <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/vxlan.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/drivers/net/vxlan.c b/drivers/net/vxlan.c
index 983e941bdf29..50570d779b01 100644
--- a/drivers/net/vxlan.c
+++ b/drivers/net/vxlan.c
@@ -2912,6 +2912,11 @@ static int vxlan_dev_configure(struct net *src_net, struct net_device *dev,
return -EINVAL;
}
+ if (lowerdev) {
+ dev->gso_max_size = lowerdev->gso_max_size;
+ dev->gso_max_segs = lowerdev->gso_max_segs;
+ }
+
if (conf->mtu) {
err = __vxlan_change_mtu(dev, lowerdev, dst, conf->mtu, false);
if (err)
--
2.14.1
From: Samuel Thibault <[email protected]>
[ Upstream commit 2ed2b8621be2708c0f6d61fe9841e9ad8b9753f0 ]
commit bbeddf52adc1 ("printk: move braille console support into
separate braille.[ch] files") introduced _braille_console_setup()
to outline the braille initialization code. There was however some
confusion over the value it was supposed to return. commit 2cfe6c4ac7ee
("printk: Fix return of braille_register_console()") tried to fix it
but failed to.
This fixes and documents the returned value according to the use
in printk.c: non-zero return means a parsing error, and thus this
console configuration should be ignored.
Signed-off-by: Samuel Thibault <[email protected]>
Cc: Aleksey Makarov <[email protected]>
Cc: Joe Perches <[email protected]>
Cc: Ming Lei <[email protected]>
Cc: Steven Rostedt <[email protected]>
Acked-by: Petr Mladek <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
kernel/printk/braille.c | 15 ++++++++-------
kernel/printk/braille.h | 13 ++++++++++---
2 files changed, 18 insertions(+), 10 deletions(-)
diff --git a/kernel/printk/braille.c b/kernel/printk/braille.c
index d5760c42f042..61d41ca41844 100644
--- a/kernel/printk/braille.c
+++ b/kernel/printk/braille.c
@@ -2,12 +2,13 @@
#include <linux/kernel.h>
#include <linux/console.h>
+#include <linux/errno.h>
#include <linux/string.h>
#include "console_cmdline.h"
#include "braille.h"
-char *_braille_console_setup(char **str, char **brl_options)
+int _braille_console_setup(char **str, char **brl_options)
{
if (!strncmp(*str, "brl,", 4)) {
*brl_options = "";
@@ -15,14 +16,14 @@ char *_braille_console_setup(char **str, char **brl_options)
} else if (!strncmp(*str, "brl=", 4)) {
*brl_options = *str + 4;
*str = strchr(*brl_options, ',');
- if (!*str)
+ if (!*str) {
pr_err("need port name after brl=\n");
- else
- *((*str)++) = 0;
- } else
- return NULL;
+ return -EINVAL;
+ }
+ *((*str)++) = 0;
+ }
- return *str;
+ return 0;
}
int
diff --git a/kernel/printk/braille.h b/kernel/printk/braille.h
index 769d771145c8..749a6756843a 100644
--- a/kernel/printk/braille.h
+++ b/kernel/printk/braille.h
@@ -9,7 +9,14 @@ braille_set_options(struct console_cmdline *c, char *brl_options)
c->brl_options = brl_options;
}
-char *
+/*
+ * Setup console according to braille options.
+ * Return -EINVAL on syntax error, 0 on success (or no braille option was
+ * actually given).
+ * Modifies str to point to the serial options
+ * Sets brl_options to the parsed braille options.
+ */
+int
_braille_console_setup(char **str, char **brl_options);
int
@@ -25,10 +32,10 @@ braille_set_options(struct console_cmdline *c, char *brl_options)
{
}
-static inline char *
+static inline int
_braille_console_setup(char **str, char **brl_options)
{
- return NULL;
+ return 0;
}
static inline int
--
2.14.1
From: Manish Jaggi <[email protected]>
[ Upstream commit b77d537d00d08fcf0bf641cd3491dd7df0ad1475 ]
Only apply the Cavium ACS quirk to devices with ID in the range
0xa000-0xa0ff. These are the on-chip PCI devices for CN81xx/CN83xx/CN88xx.
Fixes: b404bcfbf035 ("PCI: Add ACS quirk for all Cavium devices")
Reported-by: Alex Williamson <[email protected]>
Signed-off-by: Manish Jaggi <[email protected]>
Acked-by: David Daney <[email protected]>
Acked-by: Alex Williamson <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/pci/quirks.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index 0c9edc9d7c44..4c9fb8b323e8 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -4104,6 +4104,9 @@ static int pci_quirk_cavium_acs(struct pci_dev *dev, u16 acs_flags)
*/
acs_flags &= ~(PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_SV | PCI_ACS_UF);
+ if (!((dev->device >= 0xa000) && (dev->device <= 0xa0ff)))
+ return -ENOTTY;
+
return acs_flags ? 0 : 1;
}
--
2.14.1
From: Dan Carpenter <[email protected]>
[ Upstream commit ca42fb9e52d155547e6cf18cf26bce3e1a6af4ea ]
The nci_spi_send() function calls kfree_skb(skb) on both error and
success so this extra kfree_skb() is a double free.
Fixes: caf6e49bf6d0 ("NFC: nfcmrvl: add spi driver")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Samuel Ortiz <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/nfc/nfcmrvl/spi.c | 5 ++---
1 file changed, 2 insertions(+), 3 deletions(-)
diff --git a/drivers/nfc/nfcmrvl/spi.c b/drivers/nfc/nfcmrvl/spi.c
index a7faa0bcc01e..fc8e78a29d77 100644
--- a/drivers/nfc/nfcmrvl/spi.c
+++ b/drivers/nfc/nfcmrvl/spi.c
@@ -96,10 +96,9 @@ static int nfcmrvl_spi_nci_send(struct nfcmrvl_private *priv,
/* Send the SPI packet */
err = nci_spi_send(drv_data->nci_spi, &drv_data->handshake_completion,
skb);
- if (err != 0) {
+ if (err)
nfc_err(priv->dev, "spi_send failed %d", err);
- kfree_skb(skb);
- }
+
return err;
}
--
2.14.1
From: Eric Dumazet <[email protected]>
[ Upstream commit 142c6594acbcc32391af9c15f8cd65c6c177698f ]
Some device drivers reset their stats at down/up events, possibly
fooling bonding stats, since they operate with relative deltas.
It is nearly not possible to fix drivers, since some of them compute the
tx/rx counters based on per rx/tx queue stats, and the queues can be
reconfigured (ethtool -L) between the down/up sequence.
Lets avoid accumulating 'negative' values that render bonding stats
useless.
It is better to lose small deltas, assuming the bonding stats are
fetched at a reasonable frequency.
Fixes: 5f0c5f73e5ef ("bonding: make global bonding stats more reliable")
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/bonding/bond_main.c | 11 ++++++++---
1 file changed, 8 insertions(+), 3 deletions(-)
diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c
index 6b4b43319ffa..c3f3096b24ae 100644
--- a/drivers/net/bonding/bond_main.c
+++ b/drivers/net/bonding/bond_main.c
@@ -3331,12 +3331,17 @@ static void bond_fold_stats(struct rtnl_link_stats64 *_res,
for (i = 0; i < sizeof(*_res) / sizeof(u64); i++) {
u64 nv = new[i];
u64 ov = old[i];
+ s64 delta = nv - ov;
/* detects if this particular field is 32bit only */
if (((nv | ov) >> 32) == 0)
- res[i] += (u32)nv - (u32)ov;
- else
- res[i] += nv - ov;
+ delta = (s64)(s32)((u32)nv - (u32)ov);
+
+ /* filter anomalies, some drivers reset their stats
+ * at down/up events.
+ */
+ if (delta > 0)
+ res[i] += delta;
}
}
--
2.14.1
From: Takashi Sakamoto <[email protected]>
[ Upstream commit 2128f78f75a36a34dfef0e127273c2f820c5c904 ]
In IEC 61883-1, when two quadlets CIP header is used, the most significant
bit in second CIP header stands. However, packets from units with MOTU
protocol version 3 have a quirk without this flag. Current packet streaming
layer handles this as protocol error.
This commit adds a new enumeration constant for this quirk, to handle MOTU
protocol version 3.
Signed-off-by: Takashi Sakamoto <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
sound/firewire/amdtp-stream.c | 5 +++--
sound/firewire/amdtp-stream.h | 3 +++
2 files changed, 6 insertions(+), 2 deletions(-)
diff --git a/sound/firewire/amdtp-stream.c b/sound/firewire/amdtp-stream.c
index 9741757436be..d0ad61f563e2 100644
--- a/sound/firewire/amdtp-stream.c
+++ b/sound/firewire/amdtp-stream.c
@@ -471,8 +471,9 @@ static int handle_in_packet(struct amdtp_stream *s,
* This module supports 'Two-quadlet CIP header with SYT field'.
* For convenience, also check FMT field is AM824 or not.
*/
- if (((cip_header[0] & CIP_EOH_MASK) == CIP_EOH) ||
- ((cip_header[1] & CIP_EOH_MASK) != CIP_EOH)) {
+ if ((((cip_header[0] & CIP_EOH_MASK) == CIP_EOH) ||
+ ((cip_header[1] & CIP_EOH_MASK) != CIP_EOH)) &&
+ (!(s->flags & CIP_HEADER_WITHOUT_EOH))) {
dev_info_ratelimited(&s->unit->device,
"Invalid CIP header for AMDTP: %08X:%08X\n",
cip_header[0], cip_header[1]);
diff --git a/sound/firewire/amdtp-stream.h b/sound/firewire/amdtp-stream.h
index f7c054bc9d92..8136bd20c8b1 100644
--- a/sound/firewire/amdtp-stream.h
+++ b/sound/firewire/amdtp-stream.h
@@ -29,6 +29,8 @@
* @CIP_JUMBO_PAYLOAD: Only for in-stream. The number of data blocks in an
* packet is larger than IEC 61883-6 defines. Current implementation
* allows 5 times as large as IEC 61883-6 defines.
+ * @CIP_HEADER_WITHOUT_EOH: Only for in-stream. CIP Header doesn't include
+ * valid EOH.
*/
enum cip_flags {
CIP_NONBLOCKING = 0x00,
@@ -39,6 +41,7 @@ enum cip_flags {
CIP_SKIP_DBC_ZERO_CHECK = 0x10,
CIP_EMPTY_HAS_WRONG_DBC = 0x20,
CIP_JUMBO_PAYLOAD = 0x40,
+ CIP_HEADER_WITHOUT_EOH = 0x80,
};
/**
--
2.14.1
From: Geert Uytterhoeven <[email protected]>
[ Upstream commit 89675f36c9e17512812b9d14d9824f8ef92782c3 ]
The second channel of the display unit uses a different module clock
than the first channel.
Fixes: 46c4f13d04d729fa ("ARM: shmobile: r8a7794: Add DU node to device tree")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Acked-by: Laurent Pinchart <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/r8a7794.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index 6c0150dcf146..9bf2051dacdb 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -916,7 +916,7 @@
interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp7_clks R8A7794_CLK_DU0>,
- <&mstp7_clks R8A7794_CLK_DU0>;
+ <&mstp7_clks R8A7794_CLK_DU1>;
clock-names = "du.0", "du.1";
status = "disabled";
--
2.14.1
From: Roger Quadros <[email protected]>
[ Upstream commit e2d54fe76997301b49311bde7ba8ef52b47896f9 ]
It seems that if L3_INIT clkdomain is kept in HW_AUTO while usb_otg_ss
is in use then there are random chances that the usb_otg_ss module
will fail to completely idle. i.e. IDLEST = 0x2 instead of 0x3.
Preventing L3_INIT from HW_AUTO while usb_otg_ss module is in use
fixes this issue.
We don't know yet if usb_otg_ss instances 3 and 4 are affected by this
issue or not so don't add this flag for those instances.
Cc: Tero Kristo <[email protected]>
Signed-off-by: Roger Quadros <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/mach-omap2/omap_hwmod_7xx_data.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
index 1ab7096af8e2..39137231f2b2 100644
--- a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
@@ -2572,6 +2572,7 @@ static struct omap_hwmod dra7xx_usb_otg_ss1_hwmod = {
.class = &dra7xx_usb_otg_ss_hwmod_class,
.clkdm_name = "l3init_clkdm",
.main_clk = "dpll_core_h13x2_ck",
+ .flags = HWMOD_CLKDM_NOAUTO,
.prcm = {
.omap4 = {
.clkctrl_offs = DRA7XX_CM_L3INIT_USB_OTG_SS1_CLKCTRL_OFFSET,
@@ -2593,6 +2594,7 @@ static struct omap_hwmod dra7xx_usb_otg_ss2_hwmod = {
.class = &dra7xx_usb_otg_ss_hwmod_class,
.clkdm_name = "l3init_clkdm",
.main_clk = "dpll_core_h13x2_ck",
+ .flags = HWMOD_CLKDM_NOAUTO,
.prcm = {
.omap4 = {
.clkctrl_offs = DRA7XX_CM_L3INIT_USB_OTG_SS2_CLKCTRL_OFFSET,
--
2.14.1
From: Shikhar Dogra <[email protected]>
[ Upstream commit 6faecba0b3da7b617bf72bef422bf0d3bb6dfe7d ]
Seems like coefficient values for m, b and R under power have been
put in the wrong order. Rearranging them properly to get correct
values of coefficients for power.
For specs, please refer to table 7 (page 35) on
http://www.analog.com/media/en/technical-documentation/data-sheets/ADM1075.pdf
Fixes: 904b296f308d ("hwmon: (adm1275) Introduce configuration data structure for coeffcients")
Signed-off-by: Shikhar Dogra <[email protected]>
Signed-off-by: Guenter Roeck <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/hwmon/pmbus/adm1275.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/hwmon/pmbus/adm1275.c b/drivers/hwmon/pmbus/adm1275.c
index 3baa4f4a8c5e..d659a02647d4 100644
--- a/drivers/hwmon/pmbus/adm1275.c
+++ b/drivers/hwmon/pmbus/adm1275.c
@@ -101,8 +101,8 @@ static const struct coefficients adm1075_coefficients[] = {
[0] = { 27169, 0, -1 }, /* voltage */
[1] = { 806, 20475, -1 }, /* current, irange25 */
[2] = { 404, 20475, -1 }, /* current, irange50 */
- [3] = { 0, -1, 8549 }, /* power, irange25 */
- [4] = { 0, -1, 4279 }, /* power, irange50 */
+ [3] = { 8549, 0, -1 }, /* power, irange25 */
+ [4] = { 4279, 0, -1 }, /* power, irange50 */
};
static const struct coefficients adm1275_coefficients[] = {
--
2.14.1
From: Shaohua Li <[email protected]>
[ Upstream commit 06cceedcca67a93ac7f7aa93bbd9980c7496d14e ]
cgroup could be throttled to a limit but when all cgroups cross high
limit, queue enters a higher state and so the group should be throttled
to a higher limit. It's possible the cgroup is sleeping because of
throttle and other cgroups don't dispatch IO any more. In this case,
nobody can trigger current downgrade/upgrade logic. To fix this issue,
we could either set up a timer to wakeup the cgroup if other cgroups are
idle or make sure this cgroup doesn't sleep too long. Setting up a timer
means we must change the timer very frequently. This patch chooses the
latter. Making cgroup sleep time not too big wouldn't change cgroup
bps/iops, but could make it wakeup more frequently, which isn't a big
issue because throtl_slice * 8 is already quite big.
Signed-off-by: Shaohua Li <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
block/blk-throttle.c | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/block/blk-throttle.c b/block/blk-throttle.c
index a3ea8260c94c..3a4c9a3c1427 100644
--- a/block/blk-throttle.c
+++ b/block/blk-throttle.c
@@ -499,6 +499,17 @@ static void throtl_dequeue_tg(struct throtl_grp *tg)
static void throtl_schedule_pending_timer(struct throtl_service_queue *sq,
unsigned long expires)
{
+ unsigned long max_expire = jiffies + 8 * throtl_slice;
+
+ /*
+ * Since we are adjusting the throttle limit dynamically, the sleep
+ * time calculated according to previous limit might be invalid. It's
+ * possible the cgroup sleep time is very long and no other cgroups
+ * have IO running so notify the limit changes. Make sure the cgroup
+ * doesn't sleep too long to avoid the missed notification.
+ */
+ if (time_after(expires, max_expire))
+ expires = max_expire;
mod_timer(&sq->pending_timer, expires);
throtl_log(sq, "schedule timer. delay=%lu jiffies=%lu",
expires - jiffies, jiffies);
--
2.14.1
From: Jitendra Bhivare <[email protected]>
[ Upstream commit eb419229be58dc6d4a3a814116a265908e088c39 ]
scsi host12: BS_1377 : mgmt_invalidate_connection Failed for cid=256
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffff81332ebf>] __list_add+0xf/0xc0
PGD 0
Oops: 0000 [#1] SMP
Modules linked in:
...
CPU: 9 PID: 1542 Comm: iscsid Tainted: G ------------ T 3.10.0-514.el7.x86_64 #1
Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9, BIOS P89 09/12/2016
task: ffff88076f310fb0 ti: ffff88076bba8000 task.ti: ffff88076bba8000
RIP: 0010:[<ffffffff81332ebf>] [<ffffffff81332ebf>] __list_add+0xf/0xc0
RSP: 0018:ffff88076bbab8e8 EFLAGS: 00010046
RAX: 0000000000000246 RBX: ffff88076bbab990 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff880468badf58 RDI: ffff88076bbab990
RBP: ffff88076bbab900 R08: 0000000000000246 R09: 00000000000020de
R10: 0000000000000000 R11: ffff88076bbab5be R12: 0000000000000000
R13: ffff880468badf58 R14: 000000000001adb0 R15: ffff88076f310fb0
FS: 00007f377124a880(0000) GS:ffff88046fa40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 0000000771318000 CR4: 00000000001407e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffff88076bbab990 ffff880468badf50 0000000000000001 ffff88076bbab938
ffffffff810b128b 0000000000000246 00000000cf9b7040 ffff880468bac7a0
0000000000000000 ffff880468bac7a0 ffff88076bbab9d0 ffffffffa05a6ea3
Call Trace:
[<ffffffff810b128b>] prepare_to_wait+0x7b/0x90
[<ffffffffa05a6ea3>] beiscsi_mccq_compl_wait+0x153/0x330 [be2iscsi]
[<ffffffff810b1600>] ? wake_up_atomic_t+0x30/0x30
[<ffffffffa05981b1>] beiscsi_ep_disconnect+0x91/0x2d0 [be2iscsi]
[<ffffffffa0202ffa>] iscsi_if_ep_disconnect.isra.14+0x5a/0x70 [scsi_transport_iscsi]
[<ffffffffa02042fb>] iscsi_if_recv_msg+0x113b/0x14a0 [scsi_transport_iscsi]
[<ffffffff811dffd8>] ? __kmalloc_node_track_caller+0x58/0x290
[<ffffffffa02046ee>] iscsi_if_rx+0x8e/0x1f0 [scsi_transport_iscsi]
[<ffffffff815a351d>] netlink_unicast+0xed/0x1b0
[<ffffffff815a38fe>] netlink_sendmsg+0x31e/0x690
[<ffffffff815a03e4>] ? netlink_rcv_wake+0x44/0x60
[<ffffffff815a19e3>] ? netlink_recvmsg+0x1e3/0x450
beiscsi_mccq_compl_wait gets called even when MCC tag allocation failed
for mgmt_invalidate_connection. mcc_wait is not initialized for tag 0
so causes crash in prepare_to_wait.
Signed-off-by: Jitendra Bhivare <[email protected]>
Reviewed-by: Tomas Henzl <[email protected]>
Reviewed-by: Chris Leech <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/scsi/be2iscsi/be_cmds.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/scsi/be2iscsi/be_cmds.c b/drivers/scsi/be2iscsi/be_cmds.c
index be65da2988fb..838edbba8aec 100644
--- a/drivers/scsi/be2iscsi/be_cmds.c
+++ b/drivers/scsi/be2iscsi/be_cmds.c
@@ -246,6 +246,12 @@ int beiscsi_mccq_compl_wait(struct beiscsi_hba *phba,
{
int rc = 0;
+ if (!tag || tag > MAX_MCC_CMD) {
+ __beiscsi_log(phba, KERN_ERR,
+ "BC_%d : invalid tag %u\n", tag);
+ return -EINVAL;
+ }
+
if (beiscsi_hba_in_error(phba)) {
clear_bit(MCC_TAG_STATE_RUNNING,
&phba->ctrl.ptag_state[tag].tag_state);
--
2.14.1
From: "Kirill A. Shutemov" <[email protected]>
[ Upstream commit 591a3d7c09fa08baff48ad86c2347dbd28a52753 ]
0day testing by Fengguang Wu triggered this crash while running Trinity:
kernel BUG at include/linux/pagemap.h:151!
...
CPU: 0 PID: 458 Comm: trinity-c0 Not tainted 4.11.0-rc2-00251-g2947ba0 #1
...
Call Trace:
__get_user_pages_fast()
get_user_pages_fast()
get_futex_key()
futex_requeue()
do_futex()
SyS_futex()
do_syscall_64()
entry_SYSCALL64_slow_path()
It' VM_BUG_ON() due to false-negative in_atomic(). We call
page_cache_get_speculative() with disabled local interrupts.
It should be atomic enough.
So let's check for disabled interrupts in the VM_BUG_ON() condition
too, to resolve this.
( This got triggered by the conversion of the x86 GUP code to the
generic GUP code. )
Reported-by: Fengguang Wu <[email protected]>
Signed-off-by: Kirill A. Shutemov <[email protected]>
Cc: Andrew Morton <[email protected]>
Cc: Aneesh Kumar K.V <[email protected]>
Cc: Kirill A. Shutemov <[email protected]>
Cc: LKP <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
include/linux/pagemap.h | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/include/linux/pagemap.h b/include/linux/pagemap.h
index 7dbe9148b2f8..35f4c4d9c405 100644
--- a/include/linux/pagemap.h
+++ b/include/linux/pagemap.h
@@ -148,7 +148,7 @@ static inline int page_cache_get_speculative(struct page *page)
#ifdef CONFIG_TINY_RCU
# ifdef CONFIG_PREEMPT_COUNT
- VM_BUG_ON(!in_atomic());
+ VM_BUG_ON(!in_atomic() && !irqs_disabled());
# endif
/*
* Preempt must be disabled here - we rely on rcu_read_lock doing
@@ -186,7 +186,7 @@ static inline int page_cache_add_speculative(struct page *page, int count)
#if !defined(CONFIG_SMP) && defined(CONFIG_TREE_RCU)
# ifdef CONFIG_PREEMPT_COUNT
- VM_BUG_ON(!in_atomic());
+ VM_BUG_ON(!in_atomic() && !irqs_disabled());
# endif
VM_BUG_ON_PAGE(page_count(page) == 0, page);
page_ref_add(page, count);
--
2.14.1
From: Geert Uytterhoeven <[email protected]>
[ Upstream commit 403fe77e22eb72c962c3889efc9d4fa62e454737 ]
The second channel of the display unit uses a different module clock
than the first channel.
Fixes: 84e734f497cd48f6 ("ARM: dts: silk: add DU DT support")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Acked-by: Laurent Pinchart <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/r8a7794-silk.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts
index cf880ac06f4b..8874451fb914 100644
--- a/arch/arm/boot/dts/r8a7794-silk.dts
+++ b/arch/arm/boot/dts/r8a7794-silk.dts
@@ -425,7 +425,7 @@
status = "okay";
clocks = <&mstp7_clks R8A7794_CLK_DU0>,
- <&mstp7_clks R8A7794_CLK_DU0>,
+ <&mstp7_clks R8A7794_CLK_DU1>,
<&x2_clk>, <&x3_clk>;
clock-names = "du.0", "du.1", "dclkin.0", "dclkin.1";
--
2.14.1
From: Akinobu Mita <[email protected]>
[ Upstream commit 812613591cb652344186c4cd912304ed02138566 ]
When running the spi-loopback-test with slower clock rate like 10 KHz,
the test for 251 bytes transfer was failed. This failure triggered an
spi-omap2-mcspi's error message "DMA RX last word empty".
This message means that PIO for reading the remaining bytes due to the
DMA transfer length reduction is failed. This problem can be fixed by
polling OMAP2_MCSPI_CHSTAT_RXS bit in channel status register to wait
until the receive buffer register is filled.
Cc: Mark Brown <[email protected]>
Signed-off-by: Akinobu Mita <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/spi/spi-omap2-mcspi.c | 9 +++++----
1 file changed, 5 insertions(+), 4 deletions(-)
diff --git a/drivers/spi/spi-omap2-mcspi.c b/drivers/spi/spi-omap2-mcspi.c
index d5157b2222ce..a47cf638460a 100644
--- a/drivers/spi/spi-omap2-mcspi.c
+++ b/drivers/spi/spi-omap2-mcspi.c
@@ -454,6 +454,8 @@ omap2_mcspi_rx_dma(struct spi_device *spi, struct spi_transfer *xfer,
int elements = 0;
int word_len, element_count;
struct omap2_mcspi_cs *cs = spi->controller_state;
+ void __iomem *chstat_reg = cs->base + OMAP2_MCSPI_CHSTAT0;
+
mcspi = spi_master_get_devdata(spi->master);
mcspi_dma = &mcspi->dma_channels[spi->chip_select];
count = xfer->len;
@@ -549,8 +551,8 @@ omap2_mcspi_rx_dma(struct spi_device *spi, struct spi_transfer *xfer,
if (l & OMAP2_MCSPI_CHCONF_TURBO) {
elements--;
- if (likely(mcspi_read_cs_reg(spi, OMAP2_MCSPI_CHSTAT0)
- & OMAP2_MCSPI_CHSTAT_RXS)) {
+ if (!mcspi_wait_for_reg_bit(chstat_reg,
+ OMAP2_MCSPI_CHSTAT_RXS)) {
u32 w;
w = mcspi_read_cs_reg(spi, OMAP2_MCSPI_RX0);
@@ -568,8 +570,7 @@ omap2_mcspi_rx_dma(struct spi_device *spi, struct spi_transfer *xfer,
return count;
}
}
- if (likely(mcspi_read_cs_reg(spi, OMAP2_MCSPI_CHSTAT0)
- & OMAP2_MCSPI_CHSTAT_RXS)) {
+ if (!mcspi_wait_for_reg_bit(chstat_reg, OMAP2_MCSPI_CHSTAT_RXS)) {
u32 w;
w = mcspi_read_cs_reg(spi, OMAP2_MCSPI_RX0);
--
2.14.1
From: Mahesh Bandewar <[email protected]>
[ Upstream commit c4adfc822bf5d8e97660b6114b5a8892530ce8cb ]
bond_update_speed_duplex() retrieves speed and duplex settings. There
is a possibility of failure in retrieving these values but caller has
to assume it's always successful. This leads to having inconsistent
slave link settings. If these (speed, duplex) values cannot be
retrieved, then keeping the link UP causes problems.
The updated bond_update_speed_duplex() returns 0 on success if it
retrieves sane values for speed and duplex. On failure it returns 1
and marks the link down.
Signed-off-by: Mahesh Bandewar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/bonding/bond_main.c | 24 ++++++++++++++----------
1 file changed, 14 insertions(+), 10 deletions(-)
diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c
index 63d61c084815..6b4b43319ffa 100644
--- a/drivers/net/bonding/bond_main.c
+++ b/drivers/net/bonding/bond_main.c
@@ -371,9 +371,10 @@ down:
/* Get link speed and duplex from the slave's base driver
* using ethtool. If for some reason the call fails or the
* values are invalid, set speed and duplex to -1,
- * and return.
+ * and return. Return 1 if speed or duplex settings are
+ * UNKNOWN; 0 otherwise.
*/
-static void bond_update_speed_duplex(struct slave *slave)
+static int bond_update_speed_duplex(struct slave *slave)
{
struct net_device *slave_dev = slave->dev;
struct ethtool_link_ksettings ecmd;
@@ -383,24 +384,27 @@ static void bond_update_speed_duplex(struct slave *slave)
slave->duplex = DUPLEX_UNKNOWN;
res = __ethtool_get_link_ksettings(slave_dev, &ecmd);
- if (res < 0)
- return;
-
- if (ecmd.base.speed == 0 || ecmd.base.speed == ((__u32)-1))
- return;
-
+ if (res < 0) {
+ slave->link = BOND_LINK_DOWN;
+ return 1;
+ }
+ if (ecmd.base.speed == 0 || ecmd.base.speed == ((__u32)-1)) {
+ slave->link = BOND_LINK_DOWN;
+ return 1;
+ }
switch (ecmd.base.duplex) {
case DUPLEX_FULL:
case DUPLEX_HALF:
break;
default:
- return;
+ slave->link = BOND_LINK_DOWN;
+ return 1;
}
slave->speed = ecmd.base.speed;
slave->duplex = ecmd.base.duplex;
- return;
+ return 0;
}
const char *bond_slave_link_status(s8 link)
--
2.14.1
From: Felipe Balbi <[email protected]>
[ Upstream commit 1966b8657d058ecb95031809b607bf3fd1e01c10 ]
This bit is only supposed to be used with known
buggy PHYs, however some platforms might erroneously
set it. In order to avoid it, let's make sure this
bit is always cleared. If some PHY needs this, we
will need to add a quirk flag.
Signed-off-by: Felipe Balbi <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/usb/dwc3/core.c | 6 ++++++
drivers/usb/dwc3/core.h | 1 +
2 files changed, 7 insertions(+)
diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index fea446900cad..a0c2b8b6edd0 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -463,6 +463,12 @@ static int dwc3_phy_setup(struct dwc3 *dwc)
reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0));
+ /*
+ * Make sure UX_EXIT_PX is cleared as that causes issues with some
+ * PHYs. Also, this bit is not supposed to be used in normal operation.
+ */
+ reg &= ~DWC3_GUSB3PIPECTL_UX_EXIT_PX;
+
/*
* Above 1.94a, it is recommended to set DWC3_GUSB3PIPECTL_SUSPHY
* to '0' during coreConsultant configuration. So default value
diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index 884c43714456..bc3678e9dcb1 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -223,6 +223,7 @@
#define DWC3_GUSB3PIPECTL_PHYSOFTRST (1 << 31)
#define DWC3_GUSB3PIPECTL_U2SSINP3OK (1 << 29)
#define DWC3_GUSB3PIPECTL_DISRXDETINP3 (1 << 28)
+#define DWC3_GUSB3PIPECTL_UX_EXIT_PX (1 << 27)
#define DWC3_GUSB3PIPECTL_REQP1P2P3 (1 << 24)
#define DWC3_GUSB3PIPECTL_DEP1P2P3(n) ((n) << 19)
#define DWC3_GUSB3PIPECTL_DEP1P2P3_MASK DWC3_GUSB3PIPECTL_DEP1P2P3(7)
--
2.14.1
From: Taeung Song <[email protected]>
[ Upstream commit 6ebd2547dd24daf95a21b2bc59931de8502afcc3 ]
It is wrong way to read link name from a build-id file. Because a
build-id file is not anymore a symbolic link but build-id directory of
it is symbolic link, so fix it.
For example, if build-id file name gotten from
dso__build_id_filename() is as below,
/root/.debug/.build-id/4f/75c7d197c951659d1c1b8b5fd49bcdf8f3f8b1/elf
To correctly read link name of build-id, use the build-id dir path that
is a symbolic link, instead of the above build-id file name like below.
/root/.debug/.build-id/4f/75c7d197c951659d1c1b8b5fd49bcdf8f3f8b1
Signed-off-by: Taeung Song <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Fixes: 01412261d994 ("perf buildid-cache: Use path/to/bin/buildid/elf instead of path/to/bin/buildid")
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/perf/util/annotate.c | 10 +++++++++-
1 file changed, 9 insertions(+), 1 deletion(-)
diff --git a/tools/perf/util/annotate.c b/tools/perf/util/annotate.c
index 430d039d0079..a38227eb5450 100644
--- a/tools/perf/util/annotate.c
+++ b/tools/perf/util/annotate.c
@@ -1250,6 +1250,7 @@ static int dso__disassemble_filename(struct dso *dso, char *filename, size_t fil
{
char linkname[PATH_MAX];
char *build_id_filename;
+ char *build_id_path = NULL;
if (dso->symtab_type == DSO_BINARY_TYPE__KALLSYMS &&
!dso__is_kcore(dso))
@@ -1265,8 +1266,14 @@ static int dso__disassemble_filename(struct dso *dso, char *filename, size_t fil
goto fallback;
}
+ build_id_path = strdup(filename);
+ if (!build_id_path)
+ return -1;
+
+ dirname(build_id_path);
+
if (dso__is_kcore(dso) ||
- readlink(filename, linkname, sizeof(linkname)) < 0 ||
+ readlink(build_id_path, linkname, sizeof(linkname)) < 0 ||
strstr(linkname, DSO__NAME_KALLSYMS) ||
access(filename, R_OK)) {
fallback:
@@ -1278,6 +1285,7 @@ fallback:
__symbol__join_symfs(filename, filename_size, dso->long_name);
}
+ free(build_id_path);
return 0;
}
--
2.14.1
From: Pan Xinhui <[email protected]>
[ Upstream commit 3b5bf42b81d56085fd58692b5117f69aa77fdff7 ]
Once xmon is triggered by sysrq-x, it is enabled always afterwards even
if it is disabled during boot. This will cause a system reset interrupt
fail to dump. So keep xmon in its original state after exit.
We have several ways to set xmon on or off.
1) by a build config CONFIG_XMON_DEFAULT.
2) by a boot cmdline with xmon or xmon=early or xmon=on to enable xmon
and xmon=off to disable xmon. This value will override that in step 1.
3) by a debugfs interface, as proposed in this patchset.
And this value can override those in step 1 and 2.
Signed-off-by: Pan Xinhui <[email protected]>
Signed-off-by: Guilherme G. Piccoli <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/powerpc/xmon/xmon.c | 17 ++++++++++-------
1 file changed, 10 insertions(+), 7 deletions(-)
diff --git a/arch/powerpc/xmon/xmon.c b/arch/powerpc/xmon/xmon.c
index 760545519a0b..b975a256e606 100644
--- a/arch/powerpc/xmon/xmon.c
+++ b/arch/powerpc/xmon/xmon.c
@@ -74,6 +74,7 @@ static int xmon_gate;
#endif /* CONFIG_SMP */
static unsigned long in_xmon __read_mostly = 0;
+static int xmon_on = IS_ENABLED(CONFIG_XMON_DEFAULT);
static unsigned long adrs;
static int size = 1;
@@ -3244,6 +3245,8 @@ static void sysrq_handle_xmon(int key)
/* ensure xmon is enabled */
xmon_init(1);
debugger(get_irq_regs());
+ if (!xmon_on)
+ xmon_init(0);
}
static struct sysrq_key_op sysrq_xmon_op = {
@@ -3260,7 +3263,7 @@ static int __init setup_xmon_sysrq(void)
__initcall(setup_xmon_sysrq);
#endif /* CONFIG_MAGIC_SYSRQ */
-static int __initdata xmon_early, xmon_off;
+static int __initdata xmon_early;
static int __init early_parse_xmon(char *p)
{
@@ -3268,10 +3271,12 @@ static int __init early_parse_xmon(char *p)
/* just "xmon" is equivalent to "xmon=early" */
xmon_init(1);
xmon_early = 1;
- } else if (strncmp(p, "on", 2) == 0)
+ xmon_on = 1;
+ } else if (strncmp(p, "on", 2) == 0) {
xmon_init(1);
- else if (strncmp(p, "off", 3) == 0)
- xmon_off = 1;
+ xmon_on = 1;
+ } else if (strncmp(p, "off", 3) == 0)
+ xmon_on = 0;
else if (strncmp(p, "nobt", 4) == 0)
xmon_no_auto_backtrace = 1;
else
@@ -3283,10 +3288,8 @@ early_param("xmon", early_parse_xmon);
void __init xmon_setup(void)
{
-#ifdef CONFIG_XMON_DEFAULT
- if (!xmon_off)
+ if (xmon_on)
xmon_init(1);
-#endif
if (xmon_early)
debugger(NULL);
}
--
2.14.1
From: Davide Caratti <[email protected]>
[ Upstream commit add641e7dee31b36aee83412c29e39dd1f5e0c9c ]
after act_csum computes the checksum on skbs carrying GSO TCP/UDP packets,
subsequent segmentation fails because skb_needs_check(skb, true) returns
true. Because of that, skb_warn_bad_offload() is invoked and the following
message is displayed:
WARNING: CPU: 3 PID: 28 at net/core/dev.c:2553 skb_warn_bad_offload+0xf0/0xfd
<...>
[<ffffffff8171f486>] skb_warn_bad_offload+0xf0/0xfd
[<ffffffff8161304c>] __skb_gso_segment+0xec/0x110
[<ffffffff8161340d>] validate_xmit_skb+0x12d/0x2b0
[<ffffffff816135d2>] validate_xmit_skb_list+0x42/0x70
[<ffffffff8163c560>] sch_direct_xmit+0xd0/0x1b0
[<ffffffff8163c760>] __qdisc_run+0x120/0x270
[<ffffffff81613b3d>] __dev_queue_xmit+0x23d/0x690
[<ffffffff81613fa0>] dev_queue_xmit+0x10/0x20
Since GSO is able to compute checksum on individual segments of such skbs,
we can simply skip mangling the packet.
Signed-off-by: Davide Caratti <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
net/sched/act_csum.c | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/net/sched/act_csum.c b/net/sched/act_csum.c
index e0defcef376d..24a0c66394a0 100644
--- a/net/sched/act_csum.c
+++ b/net/sched/act_csum.c
@@ -180,6 +180,9 @@ static int tcf_csum_ipv4_tcp(struct sk_buff *skb, unsigned int ihl,
struct tcphdr *tcph;
const struct iphdr *iph;
+ if (skb_is_gso(skb) && skb_shinfo(skb)->gso_type & SKB_GSO_TCPV4)
+ return 1;
+
tcph = tcf_csum_skb_nextlayer(skb, ihl, ipl, sizeof(*tcph));
if (tcph == NULL)
return 0;
@@ -201,6 +204,9 @@ static int tcf_csum_ipv6_tcp(struct sk_buff *skb, unsigned int ihl,
struct tcphdr *tcph;
const struct ipv6hdr *ip6h;
+ if (skb_is_gso(skb) && skb_shinfo(skb)->gso_type & SKB_GSO_TCPV6)
+ return 1;
+
tcph = tcf_csum_skb_nextlayer(skb, ihl, ipl, sizeof(*tcph));
if (tcph == NULL)
return 0;
@@ -224,6 +230,9 @@ static int tcf_csum_ipv4_udp(struct sk_buff *skb, unsigned int ihl,
const struct iphdr *iph;
u16 ul;
+ if (skb_is_gso(skb) && skb_shinfo(skb)->gso_type & SKB_GSO_UDP)
+ return 1;
+
/*
* Support both UDP and UDPLITE checksum algorithms, Don't use
* udph->len to get the real length without any protocol check,
@@ -277,6 +286,9 @@ static int tcf_csum_ipv6_udp(struct sk_buff *skb, unsigned int ihl,
const struct ipv6hdr *ip6h;
u16 ul;
+ if (skb_is_gso(skb) && skb_shinfo(skb)->gso_type & SKB_GSO_UDP)
+ return 1;
+
/*
* Support both UDP and UDPLITE checksum algorithms, Don't use
* udph->len to get the real length without any protocol check,
--
2.14.1
From: Alexander Duyck <[email protected]>
[ Upstream commit 741b8b832a57402380be79d7d11a59eaf57fff3b ]
We need to reset skb back to NULL when we have freed it in the Rx cleanup
path. I found one spot where this wasn't occurring so this patch fixes it.
Change-ID: Iaca68934200732cd4a63eb0bd83b539c95f8c4dd
Signed-off-by: Alexander Duyck <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/intel/i40e/i40e_txrx.c | 1 +
drivers/net/ethernet/intel/i40evf/i40e_txrx.c | 1 +
2 files changed, 2 insertions(+)
diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.c b/drivers/net/ethernet/intel/i40e/i40e_txrx.c
index c5430394fac9..45b307d1858b 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_txrx.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.c
@@ -1820,6 +1820,7 @@ static int i40e_clean_rx_irq(struct i40e_ring *rx_ring, int budget)
*/
if (unlikely(i40e_test_staterr(rx_desc, BIT(I40E_RXD_QW1_ERROR_SHIFT)))) {
dev_kfree_skb_any(skb);
+ skb = NULL;
continue;
}
diff --git a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
index c03800d1000a..a951477a68b8 100644
--- a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
+++ b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
@@ -1262,6 +1262,7 @@ static int i40e_clean_rx_irq(struct i40e_ring *rx_ring, int budget)
*/
if (unlikely(i40e_test_staterr(rx_desc, BIT(I40E_RXD_QW1_ERROR_SHIFT)))) {
dev_kfree_skb_any(skb);
+ skb = NULL;
continue;
}
--
2.14.1
From: Jiada Wang <[email protected]>
[ Upstream commit 7f3ff14b7eb1ffad132117f08a1973b48e653d43 ]
sdma_disable_channel() cannot ensure dma is stopped to access
module's FIFOs. There is chance SDMA core is running and accessing
BD when disable of corresponding channel, this may cause sometimes
even after call of .sdma_disable_channel(), SDMA core still be
running and accessing module's FIFOs.
According to NXP R&D team a delay of one BD SDMA cost time (maximum
is 1ms) should be added after disable of the channel bit, to ensure
SDMA core has really been stopped after SDMA clients call
.device_terminate_all.
This patch introduces adds a new function sdma_disable_channel_with_delay()
which simply adds 1ms delay after call sdma_disable_channel(),
and set it as .device_terminate_all.
Signed-off-by: Jiada Wang <[email protected]>
Signed-off-by: Vinod Koul <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/dma/imx-sdma.c | 17 ++++++++++++++++-
1 file changed, 16 insertions(+), 1 deletion(-)
diff --git a/drivers/dma/imx-sdma.c b/drivers/dma/imx-sdma.c
index d1651a50c349..21726a270fc4 100644
--- a/drivers/dma/imx-sdma.c
+++ b/drivers/dma/imx-sdma.c
@@ -937,6 +937,21 @@ static int sdma_disable_channel(struct dma_chan *chan)
return 0;
}
+static int sdma_disable_channel_with_delay(struct dma_chan *chan)
+{
+ sdma_disable_channel(chan);
+
+ /*
+ * According to NXP R&D team a delay of one BD SDMA cost time
+ * (maximum is 1ms) should be added after disable of the channel
+ * bit, to ensure SDMA core has really been stopped after SDMA
+ * clients call .device_terminate_all.
+ */
+ mdelay(1);
+
+ return 0;
+}
+
static void sdma_set_watermarklevel_for_p2p(struct sdma_channel *sdmac)
{
struct sdma_engine *sdma = sdmac->sdma;
@@ -1828,7 +1843,7 @@ static int sdma_probe(struct platform_device *pdev)
sdma->dma_device.device_prep_slave_sg = sdma_prep_slave_sg;
sdma->dma_device.device_prep_dma_cyclic = sdma_prep_dma_cyclic;
sdma->dma_device.device_config = sdma_config;
- sdma->dma_device.device_terminate_all = sdma_disable_channel;
+ sdma->dma_device.device_terminate_all = sdma_disable_channel_with_delay;
sdma->dma_device.src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES);
sdma->dma_device.dst_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES);
sdma->dma_device.directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV);
--
2.14.1
From: Tommi Rantala <[email protected]>
[ Upstream commit 5a2342111c68e623e27ee7ea3d0492d8dad6bda0 ]
Valgrind was complaining:
$ valgrind ./perf list >/dev/null
==11643== Memcheck, a memory error detector
==11643== Copyright (C) 2002-2015, and GNU GPL'd, by Julian Seward et al.
==11643== Using Valgrind-3.12.0 and LibVEX; rerun with -h for copyright info
==11643== Command: ./perf list
==11643==
==11643== Conditional jump or move depends on uninitialised value(s)
==11643== at 0x4C30620: rindex (vg_replace_strmem.c:199)
==11643== by 0x49DAA9: build_id_cache__origname (build-id.c:198)
==11643== by 0x49E1C7: build_id_cache__valid_id (build-id.c:222)
==11643== by 0x49E1C7: build_id_cache__list_all (build-id.c:507)
==11643== by 0x4B9C8F: print_sdt_events (parse-events.c:2067)
==11643== by 0x4BB0B3: print_events (parse-events.c:2313)
==11643== by 0x439501: cmd_list (builtin-list.c:53)
==11643== by 0x497150: run_builtin (perf.c:359)
==11643== by 0x428CE0: handle_internal_command (perf.c:421)
==11643== by 0x428CE0: run_argv (perf.c:467)
==11643== by 0x428CE0: main (perf.c:614)
[...]
Additionally, a zero length result from readlink() is not very interesting.
Signed-off-by: Tommi Rantala <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/perf/util/build-id.c | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/tools/perf/util/build-id.c b/tools/perf/util/build-id.c
index e528c40739cc..993ef2762508 100644
--- a/tools/perf/util/build-id.c
+++ b/tools/perf/util/build-id.c
@@ -182,13 +182,17 @@ char *build_id_cache__origname(const char *sbuild_id)
char buf[PATH_MAX];
char *ret = NULL, *p;
size_t offs = 5; /* == strlen("../..") */
+ ssize_t len;
linkname = build_id_cache__linkname(sbuild_id, NULL, 0);
if (!linkname)
return NULL;
- if (readlink(linkname, buf, PATH_MAX) < 0)
+ len = readlink(linkname, buf, sizeof(buf) - 1);
+ if (len <= 0)
goto out;
+ buf[len] = '\0';
+
/* The link should be "../..<origpath>/<sbuild_id>" */
p = strrchr(buf, '/'); /* Cut off the "/<sbuild_id>" */
if (p && (p > buf + offs)) {
--
2.14.1
From: Long Li <[email protected]>
[ Upstream commit 414428c5da1c71986727c2fa5cdf1ed071e398d7 ]
A PCI_EJECT message can arrive at the same time we are calling
pci_scan_child_bus() in the workqueue for the previous PCI_BUS_RELATIONS
message or in create_root_hv_pci_bus(). In this case we could potentially
modify the bus from multiple places.
Properly lock the bus access.
Thanks Dexuan Cui <[email protected]> for pointing out the race condition
in create_root_hv_pci_bus().
Reported-by: Xiaofeng Wang <[email protected]>
Signed-off-by: Long Li <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Acked-by: K. Y. Srinivasan <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/pci/host/pci-hyperv.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/pci/host/pci-hyperv.c b/drivers/pci/host/pci-hyperv.c
index 43aa630f419a..d392a55ec0a9 100644
--- a/drivers/pci/host/pci-hyperv.c
+++ b/drivers/pci/host/pci-hyperv.c
@@ -1206,9 +1206,11 @@ static int create_root_hv_pci_bus(struct hv_pcibus_device *hbus)
hbus->pci_bus->msi = &hbus->msi_chip;
hbus->pci_bus->msi->dev = &hbus->hdev->device;
+ pci_lock_rescan_remove();
pci_scan_child_bus(hbus->pci_bus);
pci_bus_assign_resources(hbus->pci_bus);
pci_bus_add_devices(hbus->pci_bus);
+ pci_unlock_rescan_remove();
hbus->state = hv_pcibus_installed;
return 0;
}
@@ -1597,8 +1599,10 @@ static void hv_eject_device_work(struct work_struct *work)
pdev = pci_get_domain_bus_and_slot(hpdev->hbus->sysdata.domain, 0,
wslot);
if (pdev) {
+ pci_lock_rescan_remove();
pci_stop_and_remove_bus_device(pdev);
pci_dev_put(pdev);
+ pci_unlock_rescan_remove();
}
memset(&ctxt, 0, sizeof(ctxt));
--
2.14.1
From: Long Li <[email protected]>
[ Upstream commit d3a78d8bf759d8848339dcc367c4c1678b57a08b ]
hv_pci_devices_present() is called in hv_pci_remove() when we remove a PCI
device from the host, e.g., by disabling SR-IOV on a device. In
hv_pci_remove(), the bus is already removed before the call, so we don't
need to rescan the bus in the workqueue scheduled from
hv_pci_devices_present().
By introducing bus state hv_pcibus_removed, we can avoid this situation.
Reported-by: Xiaofeng Wang <[email protected]>
Signed-off-by: Long Li <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Acked-by: K. Y. Srinivasan <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/pci/host/pci-hyperv.c | 20 +++++++++++++++++---
1 file changed, 17 insertions(+), 3 deletions(-)
diff --git a/drivers/pci/host/pci-hyperv.c b/drivers/pci/host/pci-hyperv.c
index dafb4cdb2b7f..43aa630f419a 100644
--- a/drivers/pci/host/pci-hyperv.c
+++ b/drivers/pci/host/pci-hyperv.c
@@ -351,6 +351,7 @@ enum hv_pcibus_state {
hv_pcibus_init = 0,
hv_pcibus_probed,
hv_pcibus_installed,
+ hv_pcibus_removed,
hv_pcibus_maximum
};
@@ -1489,13 +1490,24 @@ static void pci_devices_present_work(struct work_struct *work)
put_pcichild(hpdev, hv_pcidev_ref_initial);
}
- /* Tell the core to rescan bus because there may have been changes. */
- if (hbus->state == hv_pcibus_installed) {
+ switch(hbus->state) {
+ case hv_pcibus_installed:
+ /*
+ * Tell the core to rescan bus
+ * because there may have been changes.
+ */
pci_lock_rescan_remove();
pci_scan_child_bus(hbus->pci_bus);
pci_unlock_rescan_remove();
- } else {
+ break;
+
+ case hv_pcibus_init:
+ case hv_pcibus_probed:
survey_child_resources(hbus);
+ break;
+
+ default:
+ break;
}
up(&hbus->enum_sem);
@@ -2170,6 +2182,7 @@ static int hv_pci_probe(struct hv_device *hdev,
hbus = kzalloc(sizeof(*hbus), GFP_KERNEL);
if (!hbus)
return -ENOMEM;
+ hbus->state = hv_pcibus_init;
/*
* The PCI bus "domain" is what is called "segment" in ACPI and
@@ -2312,6 +2325,7 @@ static int hv_pci_remove(struct hv_device *hdev)
pci_stop_root_bus(hbus->pci_bus);
pci_remove_root_bus(hbus->pci_bus);
pci_unlock_rescan_remove();
+ hbus->state = hv_pcibus_removed;
}
ret = hv_send_resources_released(hdev);
--
2.14.1
From: Kuninori Morimoto <[email protected]>
[ Upstream commit 6b8530cc056efd4a11b034ca5b1e9f7e9563f553 ]
R-Car Datasheet is indicating "SSICR.CKDV = 000 is invalid when
SSIWSR.WS_MODE = 1 or SSIWSR.CONT = 1".
Current driver will set CONT, thus, we shouldn't use CKDV = 000.
This patch fixup it.
Reported-by: Hiroyuki Yokoyama <[email protected]>
Signed-off-by: Kuninori Morimoto <[email protected]>
Tested-by: Hiroyuki Yokoyama <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
sound/soc/sh/rcar/ssi.c | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/sound/soc/sh/rcar/ssi.c b/sound/soc/sh/rcar/ssi.c
index a9a43acce30e..fefa6ad5de8b 100644
--- a/sound/soc/sh/rcar/ssi.c
+++ b/sound/soc/sh/rcar/ssi.c
@@ -232,6 +232,15 @@ static int rsnd_ssi_master_clk_start(struct rsnd_mod *mod,
*/
for (j = 0; j < ARRAY_SIZE(ssi_clk_mul_table); j++) {
+ /*
+ * It will set SSIWSR.CONT here, but SSICR.CKDV = 000
+ * with it is not allowed. (SSIWSR.WS_MODE with
+ * SSICR.CKDV = 000 is not allowed either).
+ * Skip it. See SSICR.CKDV
+ */
+ if (j == 0)
+ continue;
+
/*
* this driver is assuming that
* system word is 32bit x chan
--
2.14.1
From: Gao Feng <[email protected]>
[ Upstream commit c48367427a39ea0b85c7cf018fe4256627abfd9e ]
Because sysctl_tcp_adv_win_scale could be changed any time, so there
is one race in tcp_win_from_space.
For example,
1.sysctl_tcp_adv_win_scale<=0 (sysctl_tcp_adv_win_scale is negative now)
2.space>>(-sysctl_tcp_adv_win_scale) (sysctl_tcp_adv_win_scale is postive now)
As a result, tcp_win_from_space returns 0. It is unexpected.
Certainly if the compiler put the sysctl_tcp_adv_win_scale into one
register firstly, then use the register directly, it would be ok.
But we could not depend on the compiler behavior.
Signed-off-by: Gao Feng <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
include/net/tcp.h | 8 +++++---
1 file changed, 5 insertions(+), 3 deletions(-)
diff --git a/include/net/tcp.h b/include/net/tcp.h
index caf35e062639..18f029bcb8c7 100644
--- a/include/net/tcp.h
+++ b/include/net/tcp.h
@@ -1265,9 +1265,11 @@ void tcp_select_initial_window(int __space, __u32 mss, __u32 *rcv_wnd,
static inline int tcp_win_from_space(int space)
{
- return sysctl_tcp_adv_win_scale<=0 ?
- (space>>(-sysctl_tcp_adv_win_scale)) :
- space - (space>>sysctl_tcp_adv_win_scale);
+ int tcp_adv_win_scale = sysctl_tcp_adv_win_scale;
+
+ return tcp_adv_win_scale <= 0 ?
+ (space>>(-tcp_adv_win_scale)) :
+ space - (space>>tcp_adv_win_scale);
}
/* Note: caller must be prepared to deal with negative returns */
--
2.14.1
From: David Engraf <[email protected]>
[ Upstream commit 1b8955bc5ac575009835e371ae55e7f3af2197a9 ]
The scheduler clock framework may not use the correct timeout for the clock
wrap. This happens when a new clock driver calls sched_clock_register()
after the kernel called sched_clock_postinit(). In this case the clock wrap
timeout is too long thus sched_clock_poll() is called too late and the clock
already wrapped.
On my ARM system the scheduler was no longer scheduling any other task than
the idle task because the sched_clock() wrapped.
Signed-off-by: David Engraf <[email protected]>
Signed-off-by: John Stultz <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
kernel/time/sched_clock.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/kernel/time/sched_clock.c b/kernel/time/sched_clock.c
index a26036d37a38..382b159d8592 100644
--- a/kernel/time/sched_clock.c
+++ b/kernel/time/sched_clock.c
@@ -205,6 +205,11 @@ sched_clock_register(u64 (*read)(void), int bits, unsigned long rate)
update_clock_read_data(&rd);
+ if (sched_clock_timer.function != NULL) {
+ /* update timeout for clock wrap */
+ hrtimer_start(&sched_clock_timer, cd.wrap_kt, HRTIMER_MODE_REL);
+ }
+
r = rate;
if (r >= 4000000) {
r /= 1000000;
--
2.14.1
From: Andreas Pape <[email protected]>
[ Upstream commit a3a5129e122709306cfa6409781716c2933df99b ]
Consider the following situation which has been found in a test setup:
Gateway B has claimed client C and gateway A has the same backbone
network as B. C sends a broad- or multicast to B and directly after
this packet decides to send another packet to A due to a better TQ
value. B will forward the broad-/multicast into the backbone as it is
the responsible gw and after that A will claim C as it has been
chosen by C as the best gateway. If it now happens that A claims C
before it has received the broad-/multicast forwarded by B (due to
backbone topology or due to some delay in B when forwarding the
packet) we get a critical situation: in the current code A will
immediately unclaim C when receiving the multicast due to the
roaming client scenario although the position of C has not changed
in the mesh. If this happens the multi-/broadcast forwarded by B
will be sent back into the mesh by A and we have looping packets
until one of the gateways claims C again.
In order to prevent this, unclaiming of a client due to the roaming
client scenario is only done after a certain time is expired after
the last claim of the client. 100 ms are used here, which should be
slow enough for big backbones and slow gateways but fast enough not
to break the roaming client use case.
Acked-by: Simon Wunderlich <[email protected]>
Signed-off-by: Andreas Pape <[email protected]>
[[email protected]: fix conflicts with current version]
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
net/batman-adv/bridge_loop_avoidance.c | 20 ++++++++++++++++----
1 file changed, 16 insertions(+), 4 deletions(-)
diff --git a/net/batman-adv/bridge_loop_avoidance.c b/net/batman-adv/bridge_loop_avoidance.c
index e7f690b571ea..5419b1214abd 100644
--- a/net/batman-adv/bridge_loop_avoidance.c
+++ b/net/batman-adv/bridge_loop_avoidance.c
@@ -1964,10 +1964,22 @@ bool batadv_bla_tx(struct batadv_priv *bat_priv, struct sk_buff *skb,
/* if yes, the client has roamed and we have
* to unclaim it.
*/
- batadv_handle_unclaim(bat_priv, primary_if,
- primary_if->net_dev->dev_addr,
- ethhdr->h_source, vid);
- goto allow;
+ if (batadv_has_timed_out(claim->lasttime, 100)) {
+ /* only unclaim if the last claim entry is
+ * older than 100 ms to make sure we really
+ * have a roaming client here.
+ */
+ batadv_dbg(BATADV_DBG_BLA, bat_priv, "bla_tx(): Roaming client %pM detected. Unclaim it.\n",
+ ethhdr->h_source);
+ batadv_handle_unclaim(bat_priv, primary_if,
+ primary_if->net_dev->dev_addr,
+ ethhdr->h_source, vid);
+ goto allow;
+ } else {
+ batadv_dbg(BATADV_DBG_BLA, bat_priv, "bla_tx(): Race for claim %pM detected. Drop packet.\n",
+ ethhdr->h_source);
+ goto handled;
+ }
}
/* check if it is a multicast/broadcast frame */
--
2.14.1
From: Janusz Krzysztofik <[email protected]>
[ Upstream commit 54449af0e0b2ea43a8166611c95b730c850c3184 ]
After changes to v4l2_clk API introduced in v4.1 by commits a37462b919
'[media] V4L: remove clock name from v4l2_clk API' and 4f528afcfb
'[media] V4L: add CCF support to the v4l2_clk API', ov6650 sensor
stopped responding because v4l2_clk_get(), still called with
depreciated V4L2 clock name "mclk", started to return respective CCF
clock instead of the V4l2 one registered by soc_camera. Fix it by
calling v4l2_clk_get() with NULL clock name.
Created and tested on Amstrad Delta against Linux-4.7-rc3 with
omap1_camera fixes.
Signed-off-by: Janusz Krzysztofik <[email protected]>
Signed-off-by: Guennadi Liakhovetski <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/media/i2c/soc_camera/ov6650.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/media/i2c/soc_camera/ov6650.c b/drivers/media/i2c/soc_camera/ov6650.c
index 4bf2995e1cb8..8f85910eda5d 100644
--- a/drivers/media/i2c/soc_camera/ov6650.c
+++ b/drivers/media/i2c/soc_camera/ov6650.c
@@ -1033,7 +1033,7 @@ static int ov6650_probe(struct i2c_client *client,
priv->code = MEDIA_BUS_FMT_YUYV8_2X8;
priv->colorspace = V4L2_COLORSPACE_JPEG;
- priv->clk = v4l2_clk_get(&client->dev, "mclk");
+ priv->clk = v4l2_clk_get(&client->dev, NULL);
if (IS_ERR(priv->clk)) {
ret = PTR_ERR(priv->clk);
goto eclkget;
--
2.14.1
From: Baruch Siach <[email protected]>
[ Upstream commit 10b6c0c2e2bb8cd1be682f8d36ef597e3419cb88 ]
An alias name should have an index number even when it is the only of its type.
This allows U-Boot to add the local-mac-address property. Otherwise U-Boot
skips the alias.
Fixes: 6a93792774 ("ARM: bcm2835: dt: Add the ethernet to the device trees")
Signed-off-by: Baruch Siach <[email protected]>
Acked-by: Lubomir Rintel <[email protected]>
Reviewed-by: Eric Anholt <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/bcm283x-rpi-smsc9512.dtsi | 2 +-
arch/arm/boot/dts/bcm283x-rpi-smsc9514.dtsi | 2 +-
2 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/bcm283x-rpi-smsc9512.dtsi b/arch/arm/boot/dts/bcm283x-rpi-smsc9512.dtsi
index 12c981e51134..9a0599f711ff 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-smsc9512.dtsi
+++ b/arch/arm/boot/dts/bcm283x-rpi-smsc9512.dtsi
@@ -1,6 +1,6 @@
/ {
aliases {
- ethernet = ðernet;
+ ethernet0 = ðernet;
};
};
diff --git a/arch/arm/boot/dts/bcm283x-rpi-smsc9514.dtsi b/arch/arm/boot/dts/bcm283x-rpi-smsc9514.dtsi
index 3f0a56ebcf1f..dc7ae776db5f 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-smsc9514.dtsi
+++ b/arch/arm/boot/dts/bcm283x-rpi-smsc9514.dtsi
@@ -1,6 +1,6 @@
/ {
aliases {
- ethernet = ðernet;
+ ethernet0 = ðernet;
};
};
--
2.14.1
From: Andy Lutomirski <[email protected]>
[ Upstream commit 23b2a4ddebdd17fad265b4bb77256c2e4ec37dee ]
The x86 smpboot trampoline expects initial_page_table to have the
GDT mapped. If the GDT ends up in a virtually mapped per-cpu page,
then it won't be in the page tables at all until perc-pu areas are
set up. The result will be a triple fault the first time that the
CPU attempts to access the GDT after LGDT loads the perc-pu GDT.
This appears to be an old bug, but somehow the GDT fixmap rework
is triggering it. This seems to have something to do with the
memory layout.
Signed-off-by: Andy Lutomirski <[email protected]>
Cc: Ard Biesheuvel <[email protected]>
Cc: Boris Ostrovsky <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Brian Gerst <[email protected]>
Cc: Denys Vlasenko <[email protected]>
Cc: H. Peter Anvin <[email protected]>
Cc: Josh Poimboeuf <[email protected]>
Cc: Juergen Gross <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Matt Fleming <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Garnier <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/a553264a5972c6a86f9b5caac237470a0c74a720.1490218061.git.luto@kernel.org
Signed-off-by: Ingo Molnar <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/x86/kernel/setup.c | 15 ---------------
arch/x86/kernel/setup_percpu.c | 21 +++++++++++++++++++++
2 files changed, 21 insertions(+), 15 deletions(-)
diff --git a/arch/x86/kernel/setup.c b/arch/x86/kernel/setup.c
index 6b55012d02a3..d1a214287fe3 100644
--- a/arch/x86/kernel/setup.c
+++ b/arch/x86/kernel/setup.c
@@ -1200,21 +1200,6 @@ void __init setup_arch(char **cmdline_p)
kasan_init();
-#ifdef CONFIG_X86_32
- /* sync back kernel address range */
- clone_pgd_range(initial_page_table + KERNEL_PGD_BOUNDARY,
- swapper_pg_dir + KERNEL_PGD_BOUNDARY,
- KERNEL_PGD_PTRS);
-
- /*
- * sync back low identity map too. It is used for example
- * in the 32-bit EFI stub.
- */
- clone_pgd_range(initial_page_table,
- swapper_pg_dir + KERNEL_PGD_BOUNDARY,
- min(KERNEL_PGD_PTRS, KERNEL_PGD_BOUNDARY));
-#endif
-
tboot_probe();
map_vsyscall();
diff --git a/arch/x86/kernel/setup_percpu.c b/arch/x86/kernel/setup_percpu.c
index 2bbd27f89802..bbba27269fdd 100644
--- a/arch/x86/kernel/setup_percpu.c
+++ b/arch/x86/kernel/setup_percpu.c
@@ -287,4 +287,25 @@ void __init setup_per_cpu_areas(void)
/* Setup cpu initialized, callin, callout masks */
setup_cpu_local_masks();
+
+#ifdef CONFIG_X86_32
+ /*
+ * Sync back kernel address range. We want to make sure that
+ * all kernel mappings, including percpu mappings, are available
+ * in the smpboot asm. We can't reliably pick up percpu
+ * mappings using vmalloc_fault(), because exception dispatch
+ * needs percpu data.
+ */
+ clone_pgd_range(initial_page_table + KERNEL_PGD_BOUNDARY,
+ swapper_pg_dir + KERNEL_PGD_BOUNDARY,
+ KERNEL_PGD_PTRS);
+
+ /*
+ * sync back low identity map too. It is used for example
+ * in the 32-bit EFI stub.
+ */
+ clone_pgd_range(initial_page_table,
+ swapper_pg_dir + KERNEL_PGD_BOUNDARY,
+ min(KERNEL_PGD_PTRS, KERNEL_PGD_BOUNDARY));
+#endif
}
--
2.14.1
From: Tom Hromatka <[email protected]>
[ Upstream commit 0107042768658fea9f5f5a9c00b1c90f5dab6a06 ]
On systems with a large number of CPUs, running sysrq-<q> can cause
watchdog timeouts. There are two slow sections of code in the sysrq-<q>
path in timer_list.c.
1. print_active_timers() - This function is called by print_cpu() and
contains a slow goto loop. On a machine with hundreds of CPUs, this
loop took approximately 100ms for the first CPU in a NUMA node.
(Subsequent CPUs in the same node ran much quicker.) The total time
to print all of the CPUs is ultimately long enough to trigger the
soft lockup watchdog.
2. print_tickdevice() - This function outputs a large amount of textual
information. This function also took approximately 100ms per CPU.
Since sysrq-<q> is not a performance critical path, there should be no
harm in touching the nmi watchdog in both slow sections above. Touching
it in just one location was insufficient on systems with hundreds of
CPUs as occasional timeouts were still observed during testing.
This issue was observed on an Oracle T7 machine with 128 CPUs, but I
anticipate it may affect other systems with similarly large numbers of
CPUs.
Signed-off-by: Tom Hromatka <[email protected]>
Reviewed-by: Rob Gardner <[email protected]>
Signed-off-by: John Stultz <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
kernel/time/timer_list.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/kernel/time/timer_list.c b/kernel/time/timer_list.c
index ba7d8b288bb3..ef4f16e81283 100644
--- a/kernel/time/timer_list.c
+++ b/kernel/time/timer_list.c
@@ -16,6 +16,7 @@
#include <linux/sched.h>
#include <linux/seq_file.h>
#include <linux/kallsyms.h>
+#include <linux/nmi.h>
#include <asm/uaccess.h>
@@ -96,6 +97,9 @@ print_active_timers(struct seq_file *m, struct hrtimer_clock_base *base,
next_one:
i = 0;
+
+ touch_nmi_watchdog();
+
raw_spin_lock_irqsave(&base->cpu_base->lock, flags);
curr = timerqueue_getnext(&base->active);
@@ -207,6 +211,8 @@ print_tickdevice(struct seq_file *m, struct tick_device *td, int cpu)
{
struct clock_event_device *dev = td->evtdev;
+ touch_nmi_watchdog();
+
SEQ_printf(m, "Tick Device: mode: %d\n", td->mode);
if (cpu < 0)
SEQ_printf(m, "Broadcast device\n");
--
2.14.1
From: Brian King <[email protected]>
[ Upstream commit 66a0d59cdd12546ddf01d229de28b07ccf6d637f ]
Following a command abort or device reset, ipr's EH handlers wait for
the commands getting aborted to get sent back from the adapter prior to
returning from the EH handler. This fixes up some cases where the
completion handler was not getting called, which would have resulted in
the EH thread waiting until it timed out, greatly extending EH time.
Signed-off-by: Brian King <[email protected]>
Reviewed-by: Wendy Xiong <[email protected]>
Tested-by: Wendy Xiong <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/scsi/ipr.c | 16 ++++++++++++----
1 file changed, 12 insertions(+), 4 deletions(-)
diff --git a/drivers/scsi/ipr.c b/drivers/scsi/ipr.c
index 532474109624..c5bc41d97f84 100644
--- a/drivers/scsi/ipr.c
+++ b/drivers/scsi/ipr.c
@@ -836,8 +836,10 @@ static void ipr_sata_eh_done(struct ipr_cmnd *ipr_cmd)
qc->err_mask |= AC_ERR_OTHER;
sata_port->ioasa.status |= ATA_BUSY;
- list_add_tail(&ipr_cmd->queue, &ipr_cmd->hrrq->hrrq_free_q);
ata_qc_complete(qc);
+ if (ipr_cmd->eh_comp)
+ complete(ipr_cmd->eh_comp);
+ list_add_tail(&ipr_cmd->queue, &ipr_cmd->hrrq->hrrq_free_q);
}
/**
@@ -5947,8 +5949,10 @@ static void ipr_erp_done(struct ipr_cmnd *ipr_cmd)
res->in_erp = 0;
}
scsi_dma_unmap(ipr_cmd->scsi_cmd);
- list_add_tail(&ipr_cmd->queue, &ipr_cmd->hrrq->hrrq_free_q);
scsi_cmd->scsi_done(scsi_cmd);
+ if (ipr_cmd->eh_comp)
+ complete(ipr_cmd->eh_comp);
+ list_add_tail(&ipr_cmd->queue, &ipr_cmd->hrrq->hrrq_free_q);
}
/**
@@ -6338,8 +6342,10 @@ static void ipr_erp_start(struct ipr_ioa_cfg *ioa_cfg,
}
scsi_dma_unmap(ipr_cmd->scsi_cmd);
- list_add_tail(&ipr_cmd->queue, &ipr_cmd->hrrq->hrrq_free_q);
scsi_cmd->scsi_done(scsi_cmd);
+ if (ipr_cmd->eh_comp)
+ complete(ipr_cmd->eh_comp);
+ list_add_tail(&ipr_cmd->queue, &ipr_cmd->hrrq->hrrq_free_q);
}
/**
@@ -6365,8 +6371,10 @@ static void ipr_scsi_done(struct ipr_cmnd *ipr_cmd)
scsi_dma_unmap(scsi_cmd);
spin_lock_irqsave(ipr_cmd->hrrq->lock, lock_flags);
- list_add_tail(&ipr_cmd->queue, &ipr_cmd->hrrq->hrrq_free_q);
scsi_cmd->scsi_done(scsi_cmd);
+ if (ipr_cmd->eh_comp)
+ complete(ipr_cmd->eh_comp);
+ list_add_tail(&ipr_cmd->queue, &ipr_cmd->hrrq->hrrq_free_q);
spin_unlock_irqrestore(ipr_cmd->hrrq->lock, lock_flags);
} else {
spin_lock_irqsave(ioa_cfg->host->host_lock, lock_flags);
--
2.14.1
From: Kefeng Wang <[email protected]>
[ Upstream commit 70946723eeb859466f026274b29c6196e39149c4 ]
On old perf, when using 'perf probe -d' to delete an inexistent event,
it returns errno, eg,
-bash-4.3# perf probe -d xxx || echo $?
Info: Event "*:xxx" does not exist.
Error: Failed to delete events.
255
But now perf_del_probe_events() will always set ret = 0, different from
previous del_perf_probe_events(). After this, it returns errno again,
eg,
-bash-4.3# ./perf probe -d xxx || echo $?
"xxx" does not hit any event.
Error: Failed to delete events.
254
And it is more appropriate to return -ENOENT instead of -EPERM.
Signed-off-by: Kefeng Wang <[email protected]>
Acked-by: Masami Hiramatsu <[email protected]>
Cc: Hanjun Guo <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Wang Nan <[email protected]>
Fixes: dddc7ee32fa1 ("perf probe: Fix an error when deleting probes successfully")
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/perf/builtin-probe.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/tools/perf/builtin-probe.c b/tools/perf/builtin-probe.c
index f87996b0cb29..9a250c71840e 100644
--- a/tools/perf/builtin-probe.c
+++ b/tools/perf/builtin-probe.c
@@ -442,9 +442,9 @@ static int perf_del_probe_events(struct strfilter *filter)
}
if (ret == -ENOENT && ret2 == -ENOENT)
- pr_debug("\"%s\" does not hit any event.\n", str);
- /* Note that this is silently ignored */
- ret = 0;
+ pr_warning("\"%s\" does not hit any event.\n", str);
+ else
+ ret = 0;
error:
if (kfd >= 0)
--
2.14.1
From: Javier Martinez Canillas <[email protected]>
[ Upstream commit cf5cd9d4480a87da78768718cac194a71079b5cb ]
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
The compatible strings don't have a vendor prefix because that's how it's
used currently, and changing this will be a Device Tree ABI break.
Signed-off-by: Javier Martinez Canillas <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/input/keyboard/qt1070.c | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/drivers/input/keyboard/qt1070.c b/drivers/input/keyboard/qt1070.c
index 5a5778729e37..76bb51309a78 100644
--- a/drivers/input/keyboard/qt1070.c
+++ b/drivers/input/keyboard/qt1070.c
@@ -274,9 +274,18 @@ static const struct i2c_device_id qt1070_id[] = {
};
MODULE_DEVICE_TABLE(i2c, qt1070_id);
+#ifdef CONFIG_OF
+static const struct of_device_id qt1070_of_match[] = {
+ { .compatible = "qt1070", },
+ { },
+};
+MODULE_DEVICE_TABLE(of, qt1070_of_match);
+#endif
+
static struct i2c_driver qt1070_driver = {
.driver = {
.name = "qt1070",
+ .of_match_table = of_match_ptr(qt1070_of_match),
.pm = &qt1070_pm_ops,
},
.id_table = qt1070_id,
--
2.14.1
From: Satish Kharat <[email protected]>
[ Upstream commit 7ef539c88d7d394410d547c9f082d477093a2a22 ]
Fixing the IO stats update (Active IOs and IO completion) to prevent
"Number of Active IOs" from becoming negative in the fnistats output.
Signed-off-by: Satish Kharat <[email protected]>
Signed-off-by: Sesidhar Baddela <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/scsi/fnic/fnic_scsi.c | 16 ++++++++++------
1 file changed, 10 insertions(+), 6 deletions(-)
diff --git a/drivers/scsi/fnic/fnic_scsi.c b/drivers/scsi/fnic/fnic_scsi.c
index 44dd372aa7d3..c056b8111ad2 100644
--- a/drivers/scsi/fnic/fnic_scsi.c
+++ b/drivers/scsi/fnic/fnic_scsi.c
@@ -1127,12 +1127,6 @@ static void fnic_fcpio_itmf_cmpl_handler(struct fnic *fnic,
else
CMD_ABTS_STATUS(sc) = hdr_status;
- atomic64_dec(&fnic_stats->io_stats.active_ios);
- if (atomic64_read(&fnic->io_cmpl_skip))
- atomic64_dec(&fnic->io_cmpl_skip);
- else
- atomic64_inc(&fnic_stats->io_stats.io_completions);
-
if (!(CMD_FLAGS(sc) & (FNIC_IO_ABORTED | FNIC_IO_DONE)))
atomic64_inc(&misc_stats->no_icmnd_itmf_cmpls);
@@ -1173,6 +1167,11 @@ static void fnic_fcpio_itmf_cmpl_handler(struct fnic *fnic,
(((u64)CMD_FLAGS(sc) << 32) |
CMD_STATE(sc)));
sc->scsi_done(sc);
+ atomic64_dec(&fnic_stats->io_stats.active_ios);
+ if (atomic64_read(&fnic->io_cmpl_skip))
+ atomic64_dec(&fnic->io_cmpl_skip);
+ else
+ atomic64_inc(&fnic_stats->io_stats.io_completions);
}
}
@@ -1962,6 +1961,11 @@ int fnic_abort_cmd(struct scsi_cmnd *sc)
/* Call SCSI completion function to complete the IO */
sc->result = (DID_ABORT << 16);
sc->scsi_done(sc);
+ atomic64_dec(&fnic_stats->io_stats.active_ios);
+ if (atomic64_read(&fnic->io_cmpl_skip))
+ atomic64_dec(&fnic->io_cmpl_skip);
+ else
+ atomic64_inc(&fnic_stats->io_stats.io_completions);
}
fnic_abort_cmd_end:
--
2.14.1
From: Linus Walleij <[email protected]>
[ Upstream commit c2a736b698008d296c5010ec39077eeb5796109f ]
The moxart interrupt line flags were not respected in previous
driver: instead of assigning them per-consumer, a fixes mask
was set in the controller.
With the migration to a standard Faraday driver we need to
set up and handle the consumer flags correctly. Also remove
the Moxart-specific flags when switching to using real consumer
flags.
Extend the register window to 0x100 bytes as we may have a few
more registers in there and it doesn't hurt.
Tested-by: Jonas Jensen <[email protected]>
Signed-off-by: Jonas Jensen <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/moxart-uc7112lx.dts | 2 +-
arch/arm/boot/dts/moxart.dtsi | 17 +++++++++--------
2 files changed, 10 insertions(+), 9 deletions(-)
diff --git a/arch/arm/boot/dts/moxart-uc7112lx.dts b/arch/arm/boot/dts/moxart-uc7112lx.dts
index 10d088df0c35..4a962a26482d 100644
--- a/arch/arm/boot/dts/moxart-uc7112lx.dts
+++ b/arch/arm/boot/dts/moxart-uc7112lx.dts
@@ -6,7 +6,7 @@
*/
/dts-v1/;
-/include/ "moxart.dtsi"
+#include "moxart.dtsi"
/ {
model = "MOXA UC-7112-LX";
diff --git a/arch/arm/boot/dts/moxart.dtsi b/arch/arm/boot/dts/moxart.dtsi
index 1fd27ed65a01..64f2f44235d0 100644
--- a/arch/arm/boot/dts/moxart.dtsi
+++ b/arch/arm/boot/dts/moxart.dtsi
@@ -6,6 +6,7 @@
*/
/include/ "skeleton.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
compatible = "moxa,moxart";
@@ -36,8 +37,8 @@
ranges;
intc: interrupt-controller@98800000 {
- compatible = "moxa,moxart-ic";
- reg = <0x98800000 0x38>;
+ compatible = "moxa,moxart-ic", "faraday,ftintc010";
+ reg = <0x98800000 0x100>;
interrupt-controller;
#interrupt-cells = <2>;
interrupt-mask = <0x00080000>;
@@ -59,7 +60,7 @@
timer: timer@98400000 {
compatible = "moxa,moxart-timer";
reg = <0x98400000 0x42>;
- interrupts = <19 1>;
+ interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
clocks = <&clk_apb>;
};
@@ -80,7 +81,7 @@
dma: dma@90500000 {
compatible = "moxa,moxart-dma";
reg = <0x90500080 0x40>;
- interrupts = <24 0>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH>;
#dma-cells = <1>;
};
@@ -93,7 +94,7 @@
sdhci: sdhci@98e00000 {
compatible = "moxa,moxart-sdhci";
reg = <0x98e00000 0x5C>;
- interrupts = <5 0>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk_apb>;
dmas = <&dma 5>,
<&dma 5>;
@@ -120,7 +121,7 @@
mac0: mac@90900000 {
compatible = "moxa,moxart-mac";
reg = <0x90900000 0x90>;
- interrupts = <25 0>;
+ interrupts = <25 IRQ_TYPE_LEVEL_HIGH>;
phy-handle = <ðphy0>;
phy-mode = "mii";
status = "disabled";
@@ -129,7 +130,7 @@
mac1: mac@92000000 {
compatible = "moxa,moxart-mac";
reg = <0x92000000 0x90>;
- interrupts = <27 0>;
+ interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;
phy-handle = <ðphy1>;
phy-mode = "mii";
status = "disabled";
@@ -138,7 +139,7 @@
uart0: uart@98200000 {
compatible = "ns16550a";
reg = <0x98200000 0x20>;
- interrupts = <31 8>;
+ interrupts = <31 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clock-frequency = <14745600>;
--
2.14.1
From: Heiko Carstens <[email protected]>
[ Upstream commit 4fd4dd8bffb112d1e6549e0ff09e9fa3c8cc2b96 ]
Use MACHINE_FLAG_TOPOLOGY instead of MACHINE_HAS_TOPOLOGY when
clearing the bit that indicates if the machine provides topology
information (and if it should be used). Currently works anyway.
Fixes: 68cc795d1933 ("s390/topology: make "topology=off" parameter work")
Signed-off-by: Heiko Carstens <[email protected]>
Signed-off-by: Martin Schwidefsky <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/s390/kernel/early.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/s390/kernel/early.c b/arch/s390/kernel/early.c
index 29d87444a655..62578989c74d 100644
--- a/arch/s390/kernel/early.c
+++ b/arch/s390/kernel/early.c
@@ -372,7 +372,7 @@ static int __init topology_setup(char *str)
rc = kstrtobool(str, &enabled);
if (!rc && !enabled)
- S390_lowcore.machine_flags &= ~MACHINE_HAS_TOPOLOGY;
+ S390_lowcore.machine_flags &= ~MACHINE_FLAG_TOPOLOGY;
return rc;
}
early_param("topology", topology_setup);
--
2.14.1
From: Ravi Bangoria <[email protected]>
[ Upstream commit f0a30dca5f84fe8048271799b56677ac2279de66 ]
'*ntevs' contains number of elements present in 'tevs' array. If there
are no elements in array, 'tevs2' can be directly assigned to 'tevs'
without allocating more space. So the condition should be '*ntevs == 0'
not 'ntevs == 0'.
Signed-off-by: Ravi Bangoria <[email protected]>
Acked-by: Masami Hiramatsu <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Fixes: 42bba263eb58 ("perf probe: Allow wildcard for cached events")
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/perf/util/probe-event.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/tools/perf/util/probe-event.c b/tools/perf/util/probe-event.c
index 6a6f44dd594b..4d2e22f8bd94 100644
--- a/tools/perf/util/probe-event.c
+++ b/tools/perf/util/probe-event.c
@@ -3060,7 +3060,7 @@ concat_probe_trace_events(struct probe_trace_event **tevs, int *ntevs,
struct probe_trace_event *new_tevs;
int ret = 0;
- if (ntevs == 0) {
+ if (*ntevs == 0) {
*tevs = *tevs2;
*ntevs = ntevs2;
*tevs2 = NULL;
--
2.14.1
From: Johan Hovold <[email protected]>
[ Upstream commit ca260ece6a57dc7d751e0685f51fa2c55d851873 ]
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: a1030e92c150 ("[PATCH] zd1211rw: Convert installer CDROM device into WLAN device")
Cc: Daniel Drake <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/zydas/zd1211rw/zd_usb.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/net/wireless/zydas/zd1211rw/zd_usb.c b/drivers/net/wireless/zydas/zd1211rw/zd_usb.c
index c5effd6c6be9..01ca1d57b3d9 100644
--- a/drivers/net/wireless/zydas/zd1211rw/zd_usb.c
+++ b/drivers/net/wireless/zydas/zd1211rw/zd_usb.c
@@ -1278,6 +1278,9 @@ static int eject_installer(struct usb_interface *intf)
u8 bulk_out_ep;
int r;
+ if (iface_desc->desc.bNumEndpoints < 2)
+ return -ENODEV;
+
/* Find bulk out endpoint */
for (r = 1; r >= 0; r--) {
endpoint = &iface_desc->endpoint[r].desc;
--
2.14.1
From: "Mintz, Yuval" <[email protected]>
[ Upstream commit e50728effe1126eae39445ba144078b1305b7047 ]
The link information exists only on the leading hwfn,
but some of its derivatives [e.g., min/max rate] need to
be configured for each hwfn.
When re-basing the VF link view, use the leading hwfn
information as basis for all existing hwfns to allow
said configurations to stick.
Signed-off-by: Yuval Mintz <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/qlogic/qed/qed_sriov.c | 13 ++++++++++---
1 file changed, 10 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/qlogic/qed/qed_sriov.c b/drivers/net/ethernet/qlogic/qed/qed_sriov.c
index d2d6621fe0e5..48bc5c151336 100644
--- a/drivers/net/ethernet/qlogic/qed/qed_sriov.c
+++ b/drivers/net/ethernet/qlogic/qed/qed_sriov.c
@@ -3573,6 +3573,7 @@ static int qed_get_vf_config(struct qed_dev *cdev,
void qed_inform_vf_link_state(struct qed_hwfn *hwfn)
{
+ struct qed_hwfn *lead_hwfn = QED_LEADING_HWFN(hwfn->cdev);
struct qed_mcp_link_capabilities caps;
struct qed_mcp_link_params params;
struct qed_mcp_link_state link;
@@ -3589,9 +3590,15 @@ void qed_inform_vf_link_state(struct qed_hwfn *hwfn)
if (!vf_info)
continue;
- memcpy(¶ms, qed_mcp_get_link_params(hwfn), sizeof(params));
- memcpy(&link, qed_mcp_get_link_state(hwfn), sizeof(link));
- memcpy(&caps, qed_mcp_get_link_capabilities(hwfn),
+ /* Only hwfn0 is actually interested in the link speed.
+ * But since only it would receive an MFW indication of link,
+ * need to take configuration from it - otherwise things like
+ * rate limiting for hwfn1 VF would not work.
+ */
+ memcpy(¶ms, qed_mcp_get_link_params(lead_hwfn),
+ sizeof(params));
+ memcpy(&link, qed_mcp_get_link_state(lead_hwfn), sizeof(link));
+ memcpy(&caps, qed_mcp_get_link_capabilities(lead_hwfn),
sizeof(caps));
/* Modify link according to the VF's configured link state */
--
2.14.1
From: Andrey Vagin <[email protected]>
[ Upstream commit 88997e4208aea117627898e5f6f9801cf3cd42d2 ]
wanted_features is a set of features which have to be enabled if a
hardware allows that.
Currently when a vlan device is created, its wanted_features is set to
current features of its base device.
The problem is that the base device can get new features and they are
not propagated to vlan-s of this device.
If we look at bonding devices, they doesn't have this problem and this
patch suggests to fix this issue by the same way how it works for bonding
devices.
We meet this problem, when we try to create a vlan device over a bonding
device. When a system are booting, real devices require time to be
initialized, so bonding devices created without slaves, then vlan
devices are created and only then ethernet devices are added to the
bonding device. As a result we have vlan devices with disabled
scatter-gather.
* create a bonding device
$ ip link add bond0 type bond
$ ethtool -k bond0 | grep scatter
scatter-gather: off
tx-scatter-gather: off [requested on]
tx-scatter-gather-fraglist: off [requested on]
* create a vlan device
$ ip link add link bond0 name bond0.10 type vlan id 10
$ ethtool -k bond0.10 | grep scatter
scatter-gather: off
tx-scatter-gather: off
tx-scatter-gather-fraglist: off
* Add a slave device to bond0
$ ip link set dev eth0 master bond0
And now we can see that the bond0 device has got the scatter-gather
feature, but the bond0.10 hasn't got it.
[root@laptop linux-task-diag]# ethtool -k bond0 | grep scatter
scatter-gather: on
tx-scatter-gather: on
tx-scatter-gather-fraglist: on
[root@laptop linux-task-diag]# ethtool -k bond0.10 | grep scatter
scatter-gather: off
tx-scatter-gather: off
tx-scatter-gather-fraglist: off
With this patch the vlan device will get all new features from the
bonding device.
Here is a call trace how features which are set in this patch reach
dev->wanted_features.
register_netdevice
vlan_dev_init
...
dev->hw_features = NETIF_F_HW_CSUM | NETIF_F_SG |
NETIF_F_FRAGLIST | NETIF_F_GSO_SOFTWARE |
NETIF_F_HIGHDMA | NETIF_F_SCTP_CRC |
NETIF_F_ALL_FCOE;
dev->features |= dev->hw_features;
...
dev->wanted_features = dev->features & dev->hw_features;
__netdev_update_features(dev);
vlan_dev_fix_features
...
Cc: Alexey Kuznetsov <[email protected]>
Cc: Patrick McHardy <[email protected]>
Cc: "David S. Miller" <[email protected]>
Signed-off-by: Andrei Vagin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
net/8021q/vlan_dev.c | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/net/8021q/vlan_dev.c b/net/8021q/vlan_dev.c
index fbfacd51aa34..767144128b95 100644
--- a/net/8021q/vlan_dev.c
+++ b/net/8021q/vlan_dev.c
@@ -562,8 +562,7 @@ static int vlan_dev_init(struct net_device *dev)
NETIF_F_HIGHDMA | NETIF_F_SCTP_CRC |
NETIF_F_ALL_FCOE;
- dev->features |= real_dev->vlan_features | NETIF_F_LLTX |
- NETIF_F_GSO_SOFTWARE;
+ dev->features |= dev->hw_features | NETIF_F_LLTX;
dev->gso_max_size = real_dev->gso_max_size;
dev->gso_max_segs = real_dev->gso_max_segs;
if (dev->features & NETIF_F_VLAN_FEATURES)
--
2.14.1
From: Tomasz Kramkowski <[email protected]>
[ Upstream commit c3883fe06488a483658ba5d849b70e49bee15e7c ]
This patch fixes an issue in drivers/hid/hid-input.c where values
outside of the logical range are not clamped when "null state" bit of
the input control is not set.
This was discussed on the lists [1] and this change stems from the fact
due to the ambiguity of the HID specification it might be appropriate to
follow Microsoft's own interpretation of the specification. As noted in
Microsoft's documentation [2] in the section titled "Required HID usages
for digitizers" it is noted that values reported outside the logical
range "will be considered as invalid data and the value will be changed
to the nearest boundary value (logical min/max)."
This patch fixes an issue where the (1292:4745) Innomedia INNEX
GENESIS/ATARI reports out of range values for its X and Y axis of the
DPad which, due to the null state bit being unset, are forwarded to
userspace as is. Now these values will get clamped to the logical range
before being forwarded to userspace. This device was also used to test
this patch.
This patch expands on commit 3f3752705dbd ("HID: reject input outside
logical range only if null state is set").
[1]: http://lkml.kernel.org/r/[email protected]
[2]: https://msdn.microsoft.com/en-us/library/windows/hardware/dn672278(v=vs.85).asp
Signed-off-by: Tomasz Kramkowski <[email protected]>
Acked-by: Benjamin Tissoires <[email protected]>
Signed-off-by: Jiri Kosina <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/hid/hid-input.c | 21 ++++++++++++++-------
1 file changed, 14 insertions(+), 7 deletions(-)
diff --git a/drivers/hid/hid-input.c b/drivers/hid/hid-input.c
index 76f2527fbc60..40233315d5f5 100644
--- a/drivers/hid/hid-input.c
+++ b/drivers/hid/hid-input.c
@@ -1149,19 +1149,26 @@ void hidinput_hid_event(struct hid_device *hid, struct hid_field *field, struct
/*
* Ignore out-of-range values as per HID specification,
- * section 5.10 and 6.2.25.
+ * section 5.10 and 6.2.25, when NULL state bit is present.
+ * When it's not, clamp the value to match Microsoft's input
+ * driver as mentioned in "Required HID usages for digitizers":
+ * https://msdn.microsoft.com/en-us/library/windows/hardware/dn672278(v=vs.85).asp
*
* The logical_minimum < logical_maximum check is done so that we
* don't unintentionally discard values sent by devices which
* don't specify logical min and max.
*/
if ((field->flags & HID_MAIN_ITEM_VARIABLE) &&
- (field->flags & HID_MAIN_ITEM_NULL_STATE) &&
- (field->logical_minimum < field->logical_maximum) &&
- (value < field->logical_minimum ||
- value > field->logical_maximum)) {
- dbg_hid("Ignoring out-of-range value %x\n", value);
- return;
+ (field->logical_minimum < field->logical_maximum)) {
+ if (field->flags & HID_MAIN_ITEM_NULL_STATE &&
+ (value < field->logical_minimum ||
+ value > field->logical_maximum)) {
+ dbg_hid("Ignoring out-of-range value %x\n", value);
+ return;
+ }
+ value = clamp(value,
+ field->logical_minimum,
+ field->logical_maximum);
}
/*
--
2.14.1
From: Stefan Wahren <[email protected]>
[ Upstream commit bdd3c25423cb42171446940bca0946e0443e1a84 ]
Currently bcm2835_defconfig has CMA disabled which makes the
HDMI output on a Raspberry Pi 1 stop working during boot:
fb: switching to vc4drmfb from simple
Console: switching to colour dummy device 80x30
[drm] Initialized vc4 0.0.0 20140616 for soc:gpu on minor 0
[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[drm] Driver supports precise vblank timestamp query.
vc4-drm soc:gpu: failed to allocate buffer with size 9216000
vc4-drm soc:gpu: Failed to set initial hw configuration.
So enable CMA and DMA_CMA in bcm2835_defconfig.
Signed-off-by: Stefan Wahren <[email protected]>
Fixes: 4400d9ac05ee ("ARM: bcm2835: Enable the VC4 graphics driver in the defconfig")
Reviewed-by: Eric Anholt <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/configs/bcm2835_defconfig | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/configs/bcm2835_defconfig b/arch/arm/configs/bcm2835_defconfig
index 79de828e49ad..e32b0550a338 100644
--- a/arch/arm/configs/bcm2835_defconfig
+++ b/arch/arm/configs/bcm2835_defconfig
@@ -1,6 +1,5 @@
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SYSVIPC=y
-CONFIG_FHANDLE=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_BSD_PROCESS_ACCT=y
@@ -32,6 +31,7 @@ CONFIG_PREEMPT_VOLUNTARY=y
CONFIG_AEABI=y
CONFIG_KSM=y
CONFIG_CLEANCACHE=y
+CONFIG_CMA=y
CONFIG_SECCOMP=y
CONFIG_KEXEC=y
CONFIG_CRASH_DUMP=y
@@ -52,6 +52,7 @@ CONFIG_MAC80211=y
CONFIG_DEVTMPFS=y
CONFIG_DEVTMPFS_MOUNT=y
# CONFIG_STANDALONE is not set
+CONFIG_DMA_CMA=y
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_SCSI_CONSTANTS=y
@@ -62,7 +63,6 @@ CONFIG_USB_NET_SMSC95XX=y
CONFIG_ZD1211RW=y
CONFIG_INPUT_EVDEV=y
# CONFIG_LEGACY_PTYS is not set
-# CONFIG_DEVKMEM is not set
CONFIG_SERIAL_AMBA_PL011=y
CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
CONFIG_TTY_PRINTK=y
--
2.14.1
From: Yazen Ghannam <[email protected]>
[ Upstream commit 5204bf17031b69fa5faa4dc80a9dc1e2446d74f9 ]
When the MCA banks in __mcheck_cpu_init_generic() are polled for leftover
errors logged during boot or from the previous boot, its required to have
CPU features detected sufficiently so that the reading out and handling of
those early errors is done correctly.
If those features are not available, the decoding may miss some information
and get incomplete errors logged. For example, on SMCA systems the MCA_IPID
and MCA_SYND registers are not logged and MCA_ADDR is not masked
appropriately.
To cure that, do a subset of the basic feature detection early while the
rest happens in its usual place in __mcheck_cpu_init_vendor().
Signed-off-by: Yazen Ghannam <[email protected]>
Cc: Tony Luck <[email protected]>
Cc: linux-edac <[email protected]>
Cc: x86-ml <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
[ Massage commit message and simplify. ]
Signed-off-by: Borislav Petkov <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/x86/kernel/cpu/mcheck/mce.c | 30 ++++++++++++++++++------------
1 file changed, 18 insertions(+), 12 deletions(-)
diff --git a/arch/x86/kernel/cpu/mcheck/mce.c b/arch/x86/kernel/cpu/mcheck/mce.c
index b0cc7bd26ab5..dc39f5ace024 100644
--- a/arch/x86/kernel/cpu/mcheck/mce.c
+++ b/arch/x86/kernel/cpu/mcheck/mce.c
@@ -1692,30 +1692,35 @@ static int __mcheck_cpu_ancient_init(struct cpuinfo_x86 *c)
return 0;
}
-static void __mcheck_cpu_init_vendor(struct cpuinfo_x86 *c)
+/*
+ * Init basic CPU features needed for early decoding of MCEs.
+ */
+static void __mcheck_cpu_init_early(struct cpuinfo_x86 *c)
{
- switch (c->x86_vendor) {
- case X86_VENDOR_INTEL:
- mce_intel_feature_init(c);
- mce_adjust_timer = cmci_intel_adjust_timer;
- break;
-
- case X86_VENDOR_AMD: {
+ if (c->x86_vendor == X86_VENDOR_AMD) {
mce_flags.overflow_recov = !!cpu_has(c, X86_FEATURE_OVERFLOW_RECOV);
mce_flags.succor = !!cpu_has(c, X86_FEATURE_SUCCOR);
mce_flags.smca = !!cpu_has(c, X86_FEATURE_SMCA);
- /*
- * Install proper ops for Scalable MCA enabled processors
- */
if (mce_flags.smca) {
msr_ops.ctl = smca_ctl_reg;
msr_ops.status = smca_status_reg;
msr_ops.addr = smca_addr_reg;
msr_ops.misc = smca_misc_reg;
}
- mce_amd_feature_init(c);
+ }
+}
+static void __mcheck_cpu_init_vendor(struct cpuinfo_x86 *c)
+{
+ switch (c->x86_vendor) {
+ case X86_VENDOR_INTEL:
+ mce_intel_feature_init(c);
+ mce_adjust_timer = cmci_intel_adjust_timer;
+ break;
+
+ case X86_VENDOR_AMD: {
+ mce_amd_feature_init(c);
break;
}
@@ -1801,6 +1806,7 @@ void mcheck_cpu_init(struct cpuinfo_x86 *c)
machine_check_vector = do_machine_check;
+ __mcheck_cpu_init_early(c);
__mcheck_cpu_init_generic();
__mcheck_cpu_init_vendor(c);
__mcheck_cpu_init_clear_banks();
--
2.14.1
From: Nik Unger <[email protected]>
[ Upstream commit 5080f39e8c72e01cf37e8359023e7018e2a4901e ]
I recently reported on the netem list that iperf network benchmarks
show unexpected results when a bandwidth throttling rate has been
configured for netem. Specifically:
1) The measured link bandwidth *increases* when a higher delay is added
2) The measured link bandwidth appears higher than the specified limit
3) The measured link bandwidth for the same very slow settings varies significantly across
machines
The issue can be reproduced by using tc to configure netem with a
512kbit rate and various (none, 1us, 50ms, 100ms, 200ms) delays on a
veth pair between network namespaces, and then using iperf (or any
other network benchmarking tool) to test throughput. Complete detailed
instructions are in the original email chain here:
https://lists.linuxfoundation.org/pipermail/netem/2017-February/001672.html
There appear to be two underlying bugs causing these effects:
- The first issue causes long delays when the rate is slow and no
delay is configured (e.g., "rate 512kbit"). This is because SKBs are
not orphaned when no delay is configured, so orphaning does not
occur until *after* the rate-induced delay has been applied. For
this reason, adding a tiny delay (e.g., "rate 512kbit delay 1us")
dramatically increases the measured bandwidth.
- The second issue is that rate-induced delays are not correctly
applied, allowing SKB delays to occur in parallel. The indended
approach is to compute the delay for an SKB and to add this delay to
the end of the current queue. However, the code does not detect
existing SKBs in the queue due to improperly testing sch->q.qlen,
which is nonzero even when packets exist only in the
rbtree. Consequently, new SKBs do not wait for the current queue to
empty. When packet delays vary significantly (e.g., if packet sizes
are different), then this also causes unintended reordering.
I modified the code to expect a delay (and orphan the SKB) when a rate
is configured. I also added some defensive tests that correctly find
the latest scheduled delivery time, even if it is (unexpectedly) for a
packet in sch->q. I have tested these changes on the latest kernel
(4.11.0-rc1+) and the iperf / ping test results are as expected.
Signed-off-by: Nik Unger <[email protected]>
Signed-off-by: Stephen Hemminger <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
net/sched/sch_netem.c | 26 ++++++++++++++++++--------
1 file changed, 18 insertions(+), 8 deletions(-)
diff --git a/net/sched/sch_netem.c b/net/sched/sch_netem.c
index 9f7b380cf0a3..c73d58872cf8 100644
--- a/net/sched/sch_netem.c
+++ b/net/sched/sch_netem.c
@@ -462,7 +462,7 @@ static int netem_enqueue(struct sk_buff *skb, struct Qdisc *sch,
/* If a delay is expected, orphan the skb. (orphaning usually takes
* place at TX completion time, so _before_ the link transit delay)
*/
- if (q->latency || q->jitter)
+ if (q->latency || q->jitter || q->rate)
skb_orphan_partial(skb);
/*
@@ -530,21 +530,31 @@ static int netem_enqueue(struct sk_buff *skb, struct Qdisc *sch,
now = psched_get_time();
if (q->rate) {
- struct sk_buff *last;
+ struct netem_skb_cb *last = NULL;
+
+ if (sch->q.tail)
+ last = netem_skb_cb(sch->q.tail);
+ if (q->t_root.rb_node) {
+ struct sk_buff *t_skb;
+ struct netem_skb_cb *t_last;
+
+ t_skb = netem_rb_to_skb(rb_last(&q->t_root));
+ t_last = netem_skb_cb(t_skb);
+ if (!last ||
+ t_last->time_to_send > last->time_to_send) {
+ last = t_last;
+ }
+ }
- if (sch->q.qlen)
- last = sch->q.tail;
- else
- last = netem_rb_to_skb(rb_last(&q->t_root));
if (last) {
/*
* Last packet in queue is reference point (now),
* calculate this time bonus and subtract
* from delay.
*/
- delay -= netem_skb_cb(last)->time_to_send - now;
+ delay -= last->time_to_send - now;
delay = max_t(psched_tdiff_t, 0, delay);
- now = netem_skb_cb(last)->time_to_send;
+ now = last->time_to_send;
}
delay += packet_len_2_sched_time(qdisc_pkt_len(skb), q);
--
2.14.1
From: Arvind Yadav <[email protected]>
[ Upstream commit 0348aaa34412e24ebe622a2b1b013e68d6ae5412 ]
dss_init_ports() is not handling return errors from dpi_init_port() and
sdi_init_port(). It is also always returning 0 currently which results in
part of error handling code in dss_bind() being unused.
Fix dss_init_ports() to handle return errors from dpi_init_port() and
sdi_init_port().
Signed-off-by: Arvind Yadav <[email protected]>
Cc: [email protected]
[b.zolnierkie: fail early on errors, minor fixups]
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/video/fbdev/omap2/omapfb/dss/dss.c | 16 +++++++++++-----
1 file changed, 11 insertions(+), 5 deletions(-)
diff --git a/drivers/video/fbdev/omap2/omapfb/dss/dss.c b/drivers/video/fbdev/omap2/omapfb/dss/dss.c
index 47d7f69ad9ad..48c6500c24e1 100644
--- a/drivers/video/fbdev/omap2/omapfb/dss/dss.c
+++ b/drivers/video/fbdev/omap2/omapfb/dss/dss.c
@@ -941,11 +941,13 @@ static int dss_init_features(struct platform_device *pdev)
return 0;
}
+static void dss_uninit_ports(struct platform_device *pdev);
+
static int dss_init_ports(struct platform_device *pdev)
{
struct device_node *parent = pdev->dev.of_node;
struct device_node *port;
- int r;
+ int r, ret = 0;
if (parent == NULL)
return 0;
@@ -972,17 +974,21 @@ static int dss_init_ports(struct platform_device *pdev)
switch (port_type) {
case OMAP_DISPLAY_TYPE_DPI:
- dpi_init_port(pdev, port);
+ ret = dpi_init_port(pdev, port);
break;
case OMAP_DISPLAY_TYPE_SDI:
- sdi_init_port(pdev, port);
+ ret = sdi_init_port(pdev, port);
break;
default:
break;
}
- } while ((port = omapdss_of_get_next_port(parent, port)) != NULL);
+ } while (!ret &&
+ (port = omapdss_of_get_next_port(parent, port)) != NULL);
- return 0;
+ if (ret)
+ dss_uninit_ports(pdev);
+
+ return ret;
}
static void dss_uninit_ports(struct platform_device *pdev)
--
2.14.1
From: Chris Wilson <[email protected]>
[ Upstream commit 608b20506941969ea30d8c08dc9ae02bb87dbf7d ]
On vblank instant-off systems, we can get into a situation where the cost
of enabling and disabling the vblank IRQ around a drmWaitVblank query
dominates. And with the advent of even deeper hardware sleep state,
touching registers becomes ever more expensive. However, we know that if
the user wants the current vblank counter, they are also very likely to
immediately queue a vblank wait and so we can keep the interrupt around
and only turn it off if we have no further vblank requests queued within
the interrupt interval.
After vblank event delivery, this patch adds a shadow of one vblank where
the interrupt is kept alive for the user to query and queue another vblank
event. Similarly, if the user is using blocking drmWaitVblanks, the
interrupt will be disabled on the IRQ following the wait completion.
However, if the user is simply querying the current vblank counter and
timestamp, the interrupt will be disabled after every IRQ and the user
will enabled it again on the first query following the IRQ.
v2: Mario Kleiner -
After testing this, one more thing that would make sense is to move
the disable block at the end of drm_handle_vblank() instead of at the
top.
Turns out that if high precision timestaming is disabled or doesn't
work for some reason (as can be simulated by echo 0 >
/sys/module/drm/parameters/timestamp_precision_usec), then with your
delayed disable code at its current place, the vblank counter won't
increment anymore at all for instant queries, ie. with your other
"instant query" patches. Clients which repeatedly query the counter
and wait for it to progress will simply hang, spinning in an endless
query loop. There's that comment in vblank_disable_and_save:
"* Skip this step if there isn't any high precision timestamp
* available. In that case we can't account for this and just
* hope for the best.
*/
With the disable happening after leading edge of vblank (== hw counter
increment already happened) but before the vblank counter/timestamp
handling in drm_handle_vblank, that step is needed to keep the counter
progressing, so skipping it is bad.
Now without high precision timestamping support, a kms driver must not
set dev->vblank_disable_immediate = true, as this would cause problems
for clients, so this shouldn't matter, but it would be good to still
make this robust against a future kms driver which might have
unreliable high precision timestamping, e.g., high precision
timestamping that intermittently doesn't work.
v3: Patch before coffee needs extra coffee.
Testcase: igt/kms_vblank
Signed-off-by: Chris Wilson <[email protected]>
Cc: Ville Syrjälä <[email protected]>
Cc: Daniel Vetter <[email protected]>
Cc: Michel Dänzer <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Dave Airlie <[email protected]>,
Cc: Mario Kleiner <[email protected]>
Reviewed-by: Ville Syrjälä <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
Link: http://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/gpu/drm/drm_irq.c | 14 ++++++++++++--
1 file changed, 12 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/drm_irq.c b/drivers/gpu/drm/drm_irq.c
index 48a6167f5e7b..00c815a7c414 100644
--- a/drivers/gpu/drm/drm_irq.c
+++ b/drivers/gpu/drm/drm_irq.c
@@ -1202,9 +1202,9 @@ static void drm_vblank_put(struct drm_device *dev, unsigned int pipe)
if (atomic_dec_and_test(&vblank->refcount)) {
if (drm_vblank_offdelay == 0)
return;
- else if (dev->vblank_disable_immediate || drm_vblank_offdelay < 0)
+ else if (drm_vblank_offdelay < 0)
vblank_disable_fn((unsigned long)vblank);
- else
+ else if (!dev->vblank_disable_immediate)
mod_timer(&vblank->disable_timer,
jiffies + ((drm_vblank_offdelay * HZ)/1000));
}
@@ -1819,6 +1819,16 @@ bool drm_handle_vblank(struct drm_device *dev, unsigned int pipe)
wake_up(&vblank->queue);
drm_handle_vblank_events(dev, pipe);
+ /* With instant-off, we defer disabling the interrupt until after
+ * we finish processing the following vblank. The disable has to
+ * be last (after drm_handle_vblank_events) so that the timestamp
+ * is always accurate.
+ */
+ if (dev->vblank_disable_immediate &&
+ drm_vblank_offdelay > 0 &&
+ !atomic_read(&vblank->refcount))
+ vblank_disable_fn((unsigned long)vblank);
+
spin_unlock_irqrestore(&dev->event_lock, irqflags);
return true;
--
2.14.1
From: Oliver Neukum <[email protected]>
[ Upstream commit c4ba329cabca7c839ab48fb58b5bcc2582951a48 ]
There is a small window during which the an URB may
remain active after disconnect has returned. If in that case
already freed memory may be accessed and executed.
The fix is to poison the URB befotre the work is flushed.
Signed-off-by: Oliver Neukum <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/usb/misc/lvstest.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/usb/misc/lvstest.c b/drivers/usb/misc/lvstest.c
index d3d124753266..bd6e06ef88ac 100644
--- a/drivers/usb/misc/lvstest.c
+++ b/drivers/usb/misc/lvstest.c
@@ -433,6 +433,7 @@ static void lvs_rh_disconnect(struct usb_interface *intf)
struct lvs_rh *lvs = usb_get_intfdata(intf);
sysfs_remove_group(&intf->dev.kobj, &lvs_attr_group);
+ usb_poison_urb(lvs->urb); /* used in scheduled work */
flush_work(&lvs->rh_work);
usb_free_urb(lvs->urb);
}
--
2.14.1
From: Mohammed Shafi Shajakhan <[email protected]>
[ Upstream commit a28f6f27a88f047f03f04b9246ca260ebc91455e ]
Fetch target operating channel during potential radar detection when
the interface is just brought up, but no channel is assigned from
userspace. In this scenario rx_channel may not be having a valid pointer
hence fetch the target operating channel to avoid warnings as below
which can be triggered by the commands with DFS testing over longer run
comamnds:
iw wlan1 set type mesh
ifconfig wlan1 up (valid tgt_oper_chan only)
iw wlan1 cac trigger freq 5260 HT20 (valid rx_channel, tgt_oper_chan)
iw wlan1 cac trigger freq 5280 HT20
iw wlan1 cac trigger freq 5300 HT20
Once the CAC expires, current channel context will be removed and
we are only left with the fallback option of using 'target operating
channel'
Firmware and driver log:
ath: phy1: DFS: radar found on freq=5300: id=1, pri=1125, count=5,
count_false=4
ath: phy1: DFS: radar found on freq=5260: id=5, pri=3151, count=6,
count_false=11
ath: phy1: DFS: radar found on freq=5280: id=1, pri=1351, count=6,
count_false=4
ath: phy1: DFS: radar found on freq=5300: id=1, pri=1125, count=5,
count_false=4
ath10k_pci 0001:01:00.0: failed to derive channel for radar pulse,
treating as radar
ath10k_pci 0001:01:00.0: failed to derive channel for radar pulse,
treating as radar
Call trace:
WARNING: CPU: 1 PID: 2145 at
backports-20161201-3.14.77-9ab3068/net/wireless/chan.c:265
cfg80211_set_dfs_state+0x3c/0x88 [cfg80211]()
Workqueue: phy1 ieee80211_dfs_radar_detected_work
[mac80211]
[<c0320770>] (warn_slowpath_null) from [<bf79b90c>]
(cfg80211_set_dfs_state+0x3c/0x88 [cfg80211])
[<bf79b90c>] (cfg80211_set_dfs_state [cfg80211]) from
[<bf79697c>] (cfg80211_radar_event+0xc4/0x140 [cfg80211])
[<bf79697c>] (cfg80211_radar_event [cfg80211]) from
[<bf83c058>] (ieee80211_dfs_radar_detected_work+0xa8/0xb4 [mac80211])
[<bf83c058>] (ieee80211_dfs_radar_detected_work
[mac80211]) from [<c0339518>] (process_one_work+0x298/0x4a4)
Signed-off-by: Mohammed Shafi Shajakhan <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/ath/ath10k/wmi.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index 54df425bb0fc..e518b640aad0 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -3638,6 +3638,11 @@ static void ath10k_dfs_radar_report(struct ath10k *ar,
spin_lock_bh(&ar->data_lock);
ch = ar->rx_channel;
+
+ /* fetch target operating channel during channel change */
+ if (!ch)
+ ch = ar->tgt_oper_chan;
+
spin_unlock_bh(&ar->data_lock);
if (!ch) {
--
2.14.1
From: Mohammed Shafi Shajakhan <[email protected]>
[ Upstream commit ca07baab0b1e627ae1d4a55d190fb1c9d32a3445 ]
If DFS is not enabled in hostapd (ieee80211h=0) DFS channels shall
not be available for use even though the hardware may have the capability
to support DFS. With this configuration (DFS disabled in hostapd) trying to
bring up ath10k device in DFS channel for AP mode fails and trying to
simulate DFS in ath10k debugfs results in a warning in cfg80211 complaining
invalid channel and this should be avoided in the driver itself rather than
false propogating RADAR detection to mac80211/cfg80211. Fix this by
checking for the first vif 'is_started' state(should work for client mode
as well) as all the vifs shall be configured for the same channel
sys/kernel/debug/ieee80211/phy1/ath10k# echo 1 > dfs_simulate_radar
WARNING: at net/wireless/chan.c:265 cfg80211_radar_event+0x24/0x60
Workqueue: phy0 ieee80211_dfs_radar_detected_work [mac80211]
[<c022f2d4>] (warn_slowpath_null) from
[<bf72dab8>] (cfg80211_radar_event+0x24/0x60 [cfg80211])
[<bf72dab8>] (cfg80211_radar_event [cfg80211]) from
[<bf7813e0>] (ieee80211_dfs_radar_detected_work+0x94/0xa0 [mac80211])
[<bf7813e0>] (ieee80211_dfs_radar_detected_work [mac80211]) from
[<c0242320>] (process_one_work+0x20c/0x32c)
WARNING: at net/wireless/nl80211.c:2488 nl80211_get_mpath+0x13c/0x4cc
Workqueue: phy0 ieee80211_dfs_radar_detected_work [mac80211]
[<c022f2d4>] (warn_slowpath_null) from
[<bf72dab8>] (cfg80211_radar_event+0x24/0x60 [cfg80211])
[<bf72dab8>] (cfg80211_radar_event [cfg80211]) from
[<bf7813e0>] (ieee80211_dfs_radar_detected_work+0x94/0xa0 [mac80211])
[<bf7813e0>] (ieee80211_dfs_radar_detected_work [mac80211]) from
[<c0242320>] (process_one_work+0x20c/0x32c)
Signed-off-by: Mohammed Shafi Shajakhan <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/ath/ath10k/debug.c | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/drivers/net/wireless/ath/ath10k/debug.c b/drivers/net/wireless/ath/ath10k/debug.c
index 82a4c67f3672..6aa2b93497dd 100644
--- a/drivers/net/wireless/ath/ath10k/debug.c
+++ b/drivers/net/wireless/ath/ath10k/debug.c
@@ -1942,6 +1942,15 @@ static ssize_t ath10k_write_simulate_radar(struct file *file,
size_t count, loff_t *ppos)
{
struct ath10k *ar = file->private_data;
+ struct ath10k_vif *arvif;
+
+ /* Just check for for the first vif alone, as all the vifs will be
+ * sharing the same channel and if the channel is disabled, all the
+ * vifs will share the same 'is_started' state.
+ */
+ arvif = list_first_entry(&ar->arvifs, typeof(*arvif), list);
+ if (!arvif->is_started)
+ return -EINVAL;
ieee80211_radar_detected(ar->hw);
--
2.14.1
From: Quan Nguyen <[email protected]>
[ Upstream commit 11623fce0f9afef30c45e3f2120b063de3809a8f ]
This patch fixes the wrong logical OR operation by changing it to
bit-wise OR operation.
Fixes: 3bb502f83080 ("drivers: net: xgene: fix statistics counters race condition")
Signed-off-by: Iyappan Subramanian <[email protected]>
Signed-off-by: Quan Nguyen <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/apm/xgene/xgene_enet_main.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/apm/xgene/xgene_enet_main.c b/drivers/net/ethernet/apm/xgene/xgene_enet_main.c
index 8158d4698734..de1546a63a7f 100644
--- a/drivers/net/ethernet/apm/xgene/xgene_enet_main.c
+++ b/drivers/net/ethernet/apm/xgene/xgene_enet_main.c
@@ -537,9 +537,9 @@ static int xgene_enet_rx_frame(struct xgene_enet_desc_ring *rx_ring,
buf_pool->rx_skb[skb_index] = NULL;
/* checking for error */
- status = (GET_VAL(ELERR, le64_to_cpu(raw_desc->m0)) << LERR_LEN) ||
+ status = (GET_VAL(ELERR, le64_to_cpu(raw_desc->m0)) << LERR_LEN) |
GET_VAL(LERR, le64_to_cpu(raw_desc->m0));
- if (unlikely(status > 2)) {
+ if (unlikely(status)) {
dev_kfree_skb_any(skb);
xgene_enet_parse_error(rx_ring, netdev_priv(rx_ring->ndev),
status);
--
2.14.1
From: Iyappan Subramanian <[email protected]>
[ Upstream commit 0a0400c3094b5d5cedd479ddbf1329de74c09c4b ]
This patch fixes Rx checksum validation logic and
adds NETIF_F_RXCSUM flag.
Signed-off-by: Iyappan Subramanian <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/apm/xgene/xgene_enet_main.c | 27 +++++++++++++++---------
1 file changed, 17 insertions(+), 10 deletions(-)
diff --git a/drivers/net/ethernet/apm/xgene/xgene_enet_main.c b/drivers/net/ethernet/apm/xgene/xgene_enet_main.c
index de1546a63a7f..651f308cdc60 100644
--- a/drivers/net/ethernet/apm/xgene/xgene_enet_main.c
+++ b/drivers/net/ethernet/apm/xgene/xgene_enet_main.c
@@ -505,14 +505,24 @@ static netdev_tx_t xgene_enet_start_xmit(struct sk_buff *skb,
return NETDEV_TX_OK;
}
-static void xgene_enet_skip_csum(struct sk_buff *skb)
+static void xgene_enet_rx_csum(struct sk_buff *skb)
{
+ struct net_device *ndev = skb->dev;
struct iphdr *iph = ip_hdr(skb);
- if (!ip_is_fragment(iph) ||
- (iph->protocol != IPPROTO_TCP && iph->protocol != IPPROTO_UDP)) {
- skb->ip_summed = CHECKSUM_UNNECESSARY;
- }
+ if (!(ndev->features & NETIF_F_RXCSUM))
+ return;
+
+ if (skb->protocol != htons(ETH_P_IP))
+ return;
+
+ if (ip_is_fragment(iph))
+ return;
+
+ if (iph->protocol != IPPROTO_TCP && iph->protocol != IPPROTO_UDP)
+ return;
+
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
}
static int xgene_enet_rx_frame(struct xgene_enet_desc_ring *rx_ring,
@@ -555,10 +565,7 @@ static int xgene_enet_rx_frame(struct xgene_enet_desc_ring *rx_ring,
skb_checksum_none_assert(skb);
skb->protocol = eth_type_trans(skb, ndev);
- if (likely((ndev->features & NETIF_F_IP_CSUM) &&
- skb->protocol == htons(ETH_P_IP))) {
- xgene_enet_skip_csum(skb);
- }
+ xgene_enet_rx_csum(skb);
rx_ring->rx_packets++;
rx_ring->rx_bytes += datalen;
@@ -1725,7 +1732,7 @@ static int xgene_enet_probe(struct platform_device *pdev)
xgene_enet_setup_ops(pdata);
if (pdata->phy_mode == PHY_INTERFACE_MODE_XGMII) {
- ndev->features |= NETIF_F_TSO;
+ ndev->features |= NETIF_F_TSO | NETIF_F_RXCSUM;
spin_lock_init(&pdata->mss_lock);
}
ndev->hw_features = ndev->features;
--
2.14.1
From: Aaron Salter <[email protected]>
[ Upstream commit 96a39aed25e6559b160786117df124084feb9080 ]
Acquire NVM lock before reads on all devices. Previously, locks were
only used for X722 and later. Fixes an issue where simultaneous X710
NVM accesses were interfering with each other.
Change-ID: If570bb7acf958cef58725ec2a2011cead6f80638
Signed-off-by: Aaron Salter <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/intel/i40e/i40e_nvm.c | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/drivers/net/ethernet/intel/i40e/i40e_nvm.c b/drivers/net/ethernet/intel/i40e/i40e_nvm.c
index 954efe3118db..abe290bfc638 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_nvm.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_nvm.c
@@ -292,14 +292,14 @@ i40e_status i40e_read_nvm_word(struct i40e_hw *hw, u16 offset,
{
enum i40e_status_code ret_code = 0;
- if (hw->flags & I40E_HW_FLAG_AQ_SRCTL_ACCESS_ENABLE) {
- ret_code = i40e_acquire_nvm(hw, I40E_RESOURCE_READ);
- if (!ret_code) {
+ ret_code = i40e_acquire_nvm(hw, I40E_RESOURCE_READ);
+ if (!ret_code) {
+ if (hw->flags & I40E_HW_FLAG_AQ_SRCTL_ACCESS_ENABLE) {
ret_code = i40e_read_nvm_word_aq(hw, offset, data);
- i40e_release_nvm(hw);
+ } else {
+ ret_code = i40e_read_nvm_word_srctl(hw, offset, data);
}
- } else {
- ret_code = i40e_read_nvm_word_srctl(hw, offset, data);
+ i40e_release_nvm(hw);
}
return ret_code;
}
--
2.14.1
From: Lihong Yang <[email protected]>
[ Upstream commit c271dd6c391b535226cf1a81aaad9f33cb5899d3 ]
Currently ethtool -e will error out with a X722 interface
as its EEPROM has a scope limit at offset 0x5B9FFF.
This patch fixes the issue by setting the EEPROM length to
the scope limit to avoid NVM read failure beyond that.
Change-ID: I0b7d4dd6c7f2a57cace438af5dffa0f44c229372
Signed-off-by: Lihong Yang <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/intel/i40e/i40e_ethtool.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/drivers/net/ethernet/intel/i40e/i40e_ethtool.c b/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
index 92bc8846f1ba..f4569461dcb8 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
@@ -1135,6 +1135,11 @@ static int i40e_get_eeprom_len(struct net_device *netdev)
struct i40e_hw *hw = &np->vsi->back->hw;
u32 val;
+#define X722_EEPROM_SCOPE_LIMIT 0x5B9FFF
+ if (hw->mac.type == I40E_MAC_X722) {
+ val = X722_EEPROM_SCOPE_LIMIT + 1;
+ return val;
+ }
val = (rd32(hw, I40E_GLPCI_LBARCTRL)
& I40E_GLPCI_LBARCTRL_FL_SIZE_MASK)
>> I40E_GLPCI_LBARCTRL_FL_SIZE_SHIFT;
--
2.14.1
From: Quan Nguyen <[email protected]>
[ Upstream commit 4b72436dc3dd2457056b22d6f147777368c869fa ]
This patches fixes a typo in the argument to xgene_enet_wr_mdio_csr().
Signed-off-by: Quan Nguyen <[email protected]>
Signed-off-by: Iyappan Subramanian <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/phy/mdio-xgene.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/phy/mdio-xgene.c b/drivers/net/phy/mdio-xgene.c
index 92af182951be..7ed54707a0e7 100644
--- a/drivers/net/phy/mdio-xgene.c
+++ b/drivers/net/phy/mdio-xgene.c
@@ -229,7 +229,7 @@ static int xgene_xfi_mdio_write(struct mii_bus *bus, int phy_id,
val = SET_VAL(HSTPHYADX, phy_id) | SET_VAL(HSTREGADX, reg) |
SET_VAL(HSTMIIMWRDAT, data);
- xgene_enet_wr_mdio_csr(addr, MIIM_FIELD_ADDR, data);
+ xgene_enet_wr_mdio_csr(addr, MIIM_FIELD_ADDR, val);
val = HSTLDCMD | SET_VAL(HSTMIIMCMD, MIIM_CMD_LEGACY_WRITE);
xgene_enet_wr_mdio_csr(addr, MIIM_COMMAND_ADDR, val);
--
2.14.1
From: Quan Nguyen <[email protected]>
[ Upstream commit e026e700d940a1ea3d3bc84d92ac668b1f015462 ]
This patch fixes the hardware checksum settings by properly program
the classifier. Otherwise, packet may be received with checksum error
on X-Gene1 SoC.
Signed-off-by: Quan Nguyen <[email protected]>
Signed-off-by: Iyappan Subramanian <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c | 1 +
drivers/net/ethernet/apm/xgene/xgene_enet_hw.h | 1 +
2 files changed, 2 insertions(+)
diff --git a/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c b/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
index 5390ae89136c..71611bd6384b 100644
--- a/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
+++ b/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
@@ -560,6 +560,7 @@ static void xgene_enet_cle_bypass(struct xgene_enet_pdata *pdata,
xgene_enet_rd_csr(pdata, CLE_BYPASS_REG0_0_ADDR, &cb);
cb |= CFG_CLE_BYPASS_EN0;
CFG_CLE_IP_PROTOCOL0_SET(&cb, 3);
+ CFG_CLE_IP_HDR_LEN_SET(&cb, 0);
xgene_enet_wr_csr(pdata, CLE_BYPASS_REG0_0_ADDR, cb);
xgene_enet_rd_csr(pdata, CLE_BYPASS_REG1_0_ADDR, &cb);
diff --git a/drivers/net/ethernet/apm/xgene/xgene_enet_hw.h b/drivers/net/ethernet/apm/xgene/xgene_enet_hw.h
index 06e598c8bc16..c82faf1a88b8 100644
--- a/drivers/net/ethernet/apm/xgene/xgene_enet_hw.h
+++ b/drivers/net/ethernet/apm/xgene/xgene_enet_hw.h
@@ -163,6 +163,7 @@ enum xgene_enet_rm {
#define CFG_RXCLK_MUXSEL0_SET(dst, val) xgene_set_bits(dst, val, 26, 3)
#define CFG_CLE_IP_PROTOCOL0_SET(dst, val) xgene_set_bits(dst, val, 16, 2)
+#define CFG_CLE_IP_HDR_LEN_SET(dst, val) xgene_set_bits(dst, val, 8, 5)
#define CFG_CLE_DSTQID0_SET(dst, val) xgene_set_bits(dst, val, 0, 12)
#define CFG_CLE_FPSEL0_SET(dst, val) xgene_set_bits(dst, val, 16, 4)
#define CFG_MACMODE_SET(dst, val) xgene_set_bits(dst, val, 18, 2)
--
2.14.1
From: Changbin Du <[email protected]>
[ Upstream commit 4b0b3aa6a2756e6115fdf275c521e4552a7082f3 ]
Skip the sample which doesn't have branch_info to avoid segmentation
fault:
The fault can be reproduced by:
perf record -a
perf report -F cycles
Signed-off-by: Changbin Du <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Fixes: 0e332f033a82 ("perf tools: Add support for cycles, weight branch_info field")
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/perf/util/sort.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/tools/perf/util/sort.c b/tools/perf/util/sort.c
index 452e15a10dd2..031e64ce7156 100644
--- a/tools/perf/util/sort.c
+++ b/tools/perf/util/sort.c
@@ -846,6 +846,9 @@ static int hist_entry__mispredict_snprintf(struct hist_entry *he, char *bf,
static int64_t
sort__cycles_cmp(struct hist_entry *left, struct hist_entry *right)
{
+ if (!left->branch_info || !right->branch_info)
+ return cmp_null(left->branch_info, right->branch_info);
+
return left->branch_info->flags.cycles -
right->branch_info->flags.cycles;
}
@@ -853,6 +856,8 @@ sort__cycles_cmp(struct hist_entry *left, struct hist_entry *right)
static int hist_entry__cycles_snprintf(struct hist_entry *he, char *bf,
size_t size, unsigned int width)
{
+ if (!he->branch_info)
+ return scnprintf(bf, size, "%-.*s", width, "N/A");
if (he->branch_info->flags.cycles == 0)
return repsep_snprintf(bf, size, "%-*s", width, "-");
return repsep_snprintf(bf, size, "%-*hd", width,
--
2.14.1
From: Dmitry Safonov <[email protected]>
[ Upstream commit 3e6ef9c80946f781fc25e8490c9875b1d2b61158 ]
mmap(MAP_32BIT) is broken due to the dependency on the TIF_ADDR32 thread
flag.
For 64bit applications MAP_32BIT will force legacy bottom-up allocations and
the 1GB address space restriction even if the application issued a compat
syscall, which should not be subject of these restrictions.
For 32bit applications, which issue 64bit syscalls the newly introduced
mmap base separation into 64-bit and compat bases changed the behaviour
because now a 64-bit mapping is returned, but due to the TIF_ADDR32
dependency MAP_32BIT is ignored. Before the separation a 32-bit mapping was
returned, so the MAP_32BIT handling was irrelevant.
Replace the check for TIF_ADDR32 with a check for the compat syscall. That
solves both the 64-bit issuing a compat syscall and the 32-bit issuing a
64-bit syscall problems.
[ tglx: Massaged changelog ]
Signed-off-by: Dmitry Safonov <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: Andy Lutomirski <[email protected]>
Cc: Cyrill Gorcunov <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: "Kirill A. Shutemov" <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/x86/kernel/sys_x86_64.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/x86/kernel/sys_x86_64.c b/arch/x86/kernel/sys_x86_64.c
index 1119414ab419..c45923e70f82 100644
--- a/arch/x86/kernel/sys_x86_64.c
+++ b/arch/x86/kernel/sys_x86_64.c
@@ -100,7 +100,7 @@ out:
static void find_start_end(unsigned long flags, unsigned long *begin,
unsigned long *end)
{
- if (!test_thread_flag(TIF_ADDR32) && (flags & MAP_32BIT)) {
+ if (!in_compat_syscall() && (flags & MAP_32BIT)) {
/* This is usually used needed to map code in small
model, so it needs to be in the first 31bit. Limit
it to that. This means we need to move the
@@ -175,7 +175,7 @@ arch_get_unmapped_area_topdown(struct file *filp, const unsigned long addr0,
return addr;
/* for MAP_32BIT mappings we force the legacy mmap base */
- if (!test_thread_flag(TIF_ADDR32) && (flags & MAP_32BIT))
+ if (!in_compat_syscall() && (flags & MAP_32BIT))
goto bottomup;
/* requesting a specific address */
--
2.14.1
From: Al Cooper <[email protected]>
[ Upstream commit 3c51b9c7f1fae00c25f1e34da649a288e3fea1ae ]
Some Host Controller hardware blocks, like the OHCI, EHCI and SDIO
controllers, have hardware blocks that are not capable of doing 64 bit
DMA. These host controllers fail on boards with >3GB of memory because
the memory above 3GB is located physically >= 0x100000000 and can only
be accessed using 64 DMA. The way Linux is currently configured for
BRCMSTB systems, the memory given to drivers for DMA through functions
like dma_alloc_coherent() comes from CMA memory and CMA memory is taken
from the top of physical memory. When these drivers get a DMA buffer
with an address >=0x100000000, they end up dropping the upper 32 bit of
the address causing the hardware to DMA to incorrect memory, typically
BMEM (custom memory carveout). This issue was discovered on a
BCM97449SSV_DDR4 system with 4GB or memory.
The fix is to enable CONFIG_ZONE_DMA. On ARM systems this makes sure
that all DMA memory is located within the first 32 bits of address
space.
Signed-off-by: Al Cooper <[email protected]>
Signed-off-by: Florian Fainelli <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/mach-bcm/Kconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/mach-bcm/Kconfig b/arch/arm/mach-bcm/Kconfig
index a0e66d8200c5..403db76e3497 100644
--- a/arch/arm/mach-bcm/Kconfig
+++ b/arch/arm/mach-bcm/Kconfig
@@ -199,6 +199,7 @@ config ARCH_BRCMSTB
select BRCMSTB_L2_IRQ
select BCM7120_L2_IRQ
select ARCH_DMA_ADDR_T_64BIT if ARM_LPAE
+ select ZONE_DMA if ARM_LPAE
select SOC_BRCMSTB
select SOC_BUS
help
--
2.14.1
From: Prarit Bhargava <[email protected]>
[ Upstream commit fda78d7a0ead144f4b2cdb582dcba47911f4952c ]
The pci_bus_type .shutdown method, pci_device_shutdown(), is called from
device_shutdown() in the kernel restart and shutdown paths.
Previously, pci_device_shutdown() called pci_msi_shutdown() and
pci_msix_shutdown(). This disables MSI and MSI-X, which causes the device
to fall back to raising interrupts via INTx. But the driver is still bound
to the device, it doesn't know about this change, and it likely doesn't
have an INTx handler, so these INTx interrupts cause "nobody cared"
warnings like this:
irq 16: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.8.2-1.el7_UNSUPPORTED.x86_64 #1
Hardware name: Hewlett-Packard HP Z820 Workstation/158B, BIOS J63 v03.90 06/
...
The MSI disabling code was added by d52877c7b1af ("pci/irq: let
pci_device_shutdown to call pci_msi_shutdown v2") because a driver left MSI
enabled and kdump failed because the kexeced kernel wasn't prepared to
receive the MSI interrupts.
Subsequent commits 1851617cd2da ("PCI/MSI: Disable MSI at enumeration even
if kernel doesn't support MSI") and e80e7edc55ba ("PCI/MSI: Initialize MSI
capability for all architectures") changed the kexeced kernel to disable
all MSIs itself so it no longer depends on the crashed kernel to clean up
after itself.
Stop disabling MSI/MSI-X in pci_device_shutdown(). This resolves the
"nobody cared" unhandled IRQ issue above. It also allows PCI serial
devices, which may rely on the MSI interrupts, to continue outputting
messages during reboot/shutdown.
[bhelgaas: changelog, drop pci_msi_shutdown() and pci_msix_shutdown() calls
altogether]
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=187351
Signed-off-by: Prarit Bhargava <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
CC: Alex Williamson <[email protected]>
CC: David Arcari <[email protected]>
CC: Myron Stowe <[email protected]>
CC: Lukas Wunner <[email protected]>
CC: Keith Busch <[email protected]>
CC: Mika Westerberg <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/pci/pci-driver.c | 2 --
1 file changed, 2 deletions(-)
diff --git a/drivers/pci/pci-driver.c b/drivers/pci/pci-driver.c
index 802997e2ddcc..d81ad841dc0c 100644
--- a/drivers/pci/pci-driver.c
+++ b/drivers/pci/pci-driver.c
@@ -463,8 +463,6 @@ static void pci_device_shutdown(struct device *dev)
if (drv && drv->shutdown)
drv->shutdown(pci_dev);
- pci_msi_shutdown(pci_dev);
- pci_msix_shutdown(pci_dev);
/*
* If this is a kexec reboot, turn off Bus Master bit on the
--
2.14.1
From: Geert Uytterhoeven <[email protected]>
[ Upstream commit 5d6a2165abd4635ecf5ece3d02fe8677f00d32c5 ]
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 6f9314ce258c8504 ("ARM: dts: r8a7791: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/r8a7791.dtsi | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 162b55c665a3..64749080e639 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -74,9 +74,8 @@
next-level-cache = <&L2_CA15>;
};
- L2_CA15: cache-controller@0 {
+ L2_CA15: cache-controller-0 {
compatible = "cache";
- reg = <0>;
power-domains = <&sysc R8A7791_PD_CA15_SCU>;
cache-unified;
cache-level = <2>;
--
2.14.1
From: Alexander Potapenko <[email protected]>
[ Upstream commit e2f586bd83177d22072b275edd4b8b872daba924 ]
KMSAN (KernelMemorySanitizer, a new error detection tool) reports use of
uninitialized memory in selinux_socket_bind():
==================================================================
BUG: KMSAN: use of unitialized memory
inter: 0
CPU: 3 PID: 1074 Comm: packet2 Tainted: G B 4.8.0-rc6+ #1916
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
0000000000000000 ffff8800882ffb08 ffffffff825759c8 ffff8800882ffa48
ffffffff818bf551 ffffffff85bab870 0000000000000092 ffffffff85bab550
0000000000000000 0000000000000092 00000000bb0009bb 0000000000000002
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff825759c8>] dump_stack+0x238/0x290 lib/dump_stack.c:51
[<ffffffff818bdee6>] kmsan_report+0x276/0x2e0 mm/kmsan/kmsan.c:1008
[<ffffffff818bf0fb>] __msan_warning+0x5b/0xb0 mm/kmsan/kmsan_instr.c:424
[<ffffffff822dae71>] selinux_socket_bind+0xf41/0x1080 security/selinux/hooks.c:4288
[<ffffffff8229357c>] security_socket_bind+0x1ec/0x240 security/security.c:1240
[<ffffffff84265d98>] SYSC_bind+0x358/0x5f0 net/socket.c:1366
[<ffffffff84265a22>] SyS_bind+0x82/0xa0 net/socket.c:1356
[<ffffffff81005678>] do_syscall_64+0x58/0x70 arch/x86/entry/common.c:292
[<ffffffff8518217c>] entry_SYSCALL64_slow_path+0x25/0x25 arch/x86/entry/entry_64.o:?
chained origin: 00000000ba6009bb
[<ffffffff810bb7a7>] save_stack_trace+0x27/0x50 arch/x86/kernel/stacktrace.c:67
[< inline >] kmsan_save_stack_with_flags mm/kmsan/kmsan.c:322
[< inline >] kmsan_save_stack mm/kmsan/kmsan.c:337
[<ffffffff818bd2b8>] kmsan_internal_chain_origin+0x118/0x1e0 mm/kmsan/kmsan.c:530
[<ffffffff818bf033>] __msan_set_alloca_origin4+0xc3/0x130 mm/kmsan/kmsan_instr.c:380
[<ffffffff84265b69>] SYSC_bind+0x129/0x5f0 net/socket.c:1356
[<ffffffff84265a22>] SyS_bind+0x82/0xa0 net/socket.c:1356
[<ffffffff81005678>] do_syscall_64+0x58/0x70 arch/x86/entry/common.c:292
[<ffffffff8518217c>] return_from_SYSCALL_64+0x0/0x6a arch/x86/entry/entry_64.o:?
origin description: ----address@SYSC_bind (origin=00000000b8c00900)
==================================================================
(the line numbers are relative to 4.8-rc6, but the bug persists upstream)
, when I run the following program as root:
=======================================================
#include <string.h>
#include <sys/socket.h>
#include <netinet/in.h>
int main(int argc, char *argv[]) {
struct sockaddr addr;
int size = 0;
if (argc > 1) {
size = atoi(argv[1]);
}
memset(&addr, 0, sizeof(addr));
int fd = socket(PF_INET6, SOCK_DGRAM, IPPROTO_IP);
bind(fd, &addr, size);
return 0;
}
=======================================================
(for different values of |size| other error reports are printed).
This happens because bind() unconditionally copies |size| bytes of
|addr| to the kernel, leaving the rest uninitialized. Then
security_socket_bind() reads the IP address bytes, including the
uninitialized ones, to determine the port, or e.g. pass them further to
sel_netnode_find(), which uses them to calculate a hash.
Signed-off-by: Alexander Potapenko <[email protected]>
Acked-by: Eric Dumazet <[email protected]>
[PM: fixed some whitespace damage]
Signed-off-by: Paul Moore <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
security/selinux/hooks.c | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/security/selinux/hooks.c b/security/selinux/hooks.c
index c2da45ae5b2a..b8278f3af9da 100644
--- a/security/selinux/hooks.c
+++ b/security/selinux/hooks.c
@@ -4328,10 +4328,18 @@ static int selinux_socket_bind(struct socket *sock, struct sockaddr *address, in
u32 sid, node_perm;
if (family == PF_INET) {
+ if (addrlen < sizeof(struct sockaddr_in)) {
+ err = -EINVAL;
+ goto out;
+ }
addr4 = (struct sockaddr_in *)address;
snum = ntohs(addr4->sin_port);
addrp = (char *)&addr4->sin_addr.s_addr;
} else {
+ if (addrlen < SIN6_LEN_RFC2133) {
+ err = -EINVAL;
+ goto out;
+ }
addr6 = (struct sockaddr_in6 *)address;
snum = ntohs(addr6->sin6_port);
addrp = (char *)&addr6->sin6_addr.s6_addr;
--
2.14.1
From: Xunlei Pang <[email protected]>
[ Upstream commit 5bc329503e8191c91c4c40836f062ef771d8ba83 ]
When we are about to kexec a crash kernel and right then and there a
broadcasted MCE fires while we're still in the first kernel and while
the other CPUs remain in a holding pattern, the #MC handler of the
first kernel will timeout and then panic due to never completing MCE
synchronization.
Handle this in a similar way as to when the CPUs are offlined when that
broadcasted MCE happens.
[ Boris: rewrote commit message and comments. ]
Suggested-by: Borislav Petkov <[email protected]>
Signed-off-by: Xunlei Pang <[email protected]>
Signed-off-by: Borislav Petkov <[email protected]>
Acked-by: Tony Luck <[email protected]>
Cc: Naoya Horiguchi <[email protected]>
Cc: [email protected]
Cc: linux-edac <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/x86/include/asm/reboot.h | 1 +
arch/x86/kernel/cpu/mcheck/mce.c | 18 ++++++++++++++++--
arch/x86/kernel/reboot.c | 5 +++--
3 files changed, 20 insertions(+), 4 deletions(-)
diff --git a/arch/x86/include/asm/reboot.h b/arch/x86/include/asm/reboot.h
index 2cb1cc253d51..fc62ba8dce93 100644
--- a/arch/x86/include/asm/reboot.h
+++ b/arch/x86/include/asm/reboot.h
@@ -15,6 +15,7 @@ struct machine_ops {
};
extern struct machine_ops machine_ops;
+extern int crashing_cpu;
void native_machine_crash_shutdown(struct pt_regs *regs);
void native_machine_shutdown(void);
diff --git a/arch/x86/kernel/cpu/mcheck/mce.c b/arch/x86/kernel/cpu/mcheck/mce.c
index fe5cd6ea1f0e..b0cc7bd26ab5 100644
--- a/arch/x86/kernel/cpu/mcheck/mce.c
+++ b/arch/x86/kernel/cpu/mcheck/mce.c
@@ -48,6 +48,7 @@
#include <asm/tlbflush.h>
#include <asm/mce.h>
#include <asm/msr.h>
+#include <asm/reboot.h>
#include "mce-internal.h"
@@ -1078,9 +1079,22 @@ void do_machine_check(struct pt_regs *regs, long error_code)
* on Intel.
*/
int lmce = 1;
+ int cpu = smp_processor_id();
- /* If this CPU is offline, just bail out. */
- if (cpu_is_offline(smp_processor_id())) {
+ /*
+ * Cases where we avoid rendezvous handler timeout:
+ * 1) If this CPU is offline.
+ *
+ * 2) If crashing_cpu was set, e.g. we're entering kdump and we need to
+ * skip those CPUs which remain looping in the 1st kernel - see
+ * crash_nmi_callback().
+ *
+ * Note: there still is a small window between kexec-ing and the new,
+ * kdump kernel establishing a new #MC handler where a broadcasted MCE
+ * might not get handled properly.
+ */
+ if (cpu_is_offline(cpu) ||
+ (crashing_cpu != -1 && crashing_cpu != cpu)) {
u64 mcgstatus;
mcgstatus = mce_rdmsrl(MSR_IA32_MCG_STATUS);
diff --git a/arch/x86/kernel/reboot.c b/arch/x86/kernel/reboot.c
index ce020a69bba9..03f21dbfaa9d 100644
--- a/arch/x86/kernel/reboot.c
+++ b/arch/x86/kernel/reboot.c
@@ -769,10 +769,11 @@ void machine_crash_shutdown(struct pt_regs *regs)
#endif
+/* This is the CPU performing the emergency shutdown work. */
+int crashing_cpu = -1;
+
#if defined(CONFIG_SMP)
-/* This keeps a track of which one is crashing cpu. */
-static int crashing_cpu;
static nmi_shootdown_cb shootdown_callback;
static atomic_t waiting_for_crash_ipi;
--
2.14.1
From: Geert Uytterhoeven <[email protected]>
[ Upstream commit beffa8872a3680ef804eb0320ec77037170f4686 ]
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: ad53f5f00b095a0d ("ARM: dts: r8a7793: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/r8a7793.dtsi | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index 8d02aacf2892..bd7ee309f509 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -65,9 +65,8 @@
power-domains = <&sysc R8A7793_PD_CA15_CPU1>;
};
- L2_CA15: cache-controller@0 {
+ L2_CA15: cache-controller-0 {
compatible = "cache";
- reg = <0>;
power-domains = <&sysc R8A7793_PD_CA15_SCU>;
cache-unified;
cache-level = <2>;
--
2.14.1
From: Chen-Yu Tsai <[email protected]>
[ Upstream commit 7544860733d158e3edbf309f27e79e258c8f66bd ]
The way drm_of_find_possible_crtcs works is it tries to match the
remote-endpoint of the given node's various endpoints to all the
crtc's .port field. Thus we need to set drm_crtc.port to the output
port node of the underlying TCON.
Signed-off-by: Chen-Yu Tsai <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/gpu/drm/sun4i/sun4i_crtc.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/drivers/gpu/drm/sun4i/sun4i_crtc.c b/drivers/gpu/drm/sun4i/sun4i_crtc.c
index 4a192210574f..caba0311c86c 100644
--- a/drivers/gpu/drm/sun4i/sun4i_crtc.c
+++ b/drivers/gpu/drm/sun4i/sun4i_crtc.c
@@ -19,6 +19,7 @@
#include <linux/clk-provider.h>
#include <linux/ioport.h>
#include <linux/of_address.h>
+#include <linux/of_graph.h>
#include <linux/of_irq.h>
#include <linux/regmap.h>
@@ -136,5 +137,9 @@ struct sun4i_crtc *sun4i_crtc_init(struct drm_device *drm)
drm_crtc_helper_add(&scrtc->crtc, &sun4i_crtc_helper_funcs);
+ /* Set crtc.port to output port node of the tcon */
+ scrtc->crtc.port = of_graph_get_port_by_id(drv->tcon->dev->of_node,
+ 1);
+
return scrtc;
}
--
2.14.1
From: Thomas Petazzoni <[email protected]>
[ Upstream commit 2067e0a13cfe0b1bdca7b91bc5e4f2740b07d478 ]
On PPv2.2, the streaming mappings can be anywhere in the first 40 bits
of the physical address space. However, for the coherent mappings, we
still need them to be in the first 32 bits of the address space,
because all BM pools share a single register to store the high 32 bits
of the BM pool address, which means all BM pools must be allocated in
the same 4GB memory area.
Signed-off-by: Thomas Petazzoni <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2.c | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/drivers/net/ethernet/marvell/mvpp2.c b/drivers/net/ethernet/marvell/mvpp2.c
index 7e2ebfc565ee..28dcef283c69 100644
--- a/drivers/net/ethernet/marvell/mvpp2.c
+++ b/drivers/net/ethernet/marvell/mvpp2.c
@@ -6420,6 +6420,20 @@ static int mvpp2_probe(struct platform_device *pdev)
/* Get system's tclk rate */
priv->tclk = clk_get_rate(priv->pp_clk);
+ if (priv->hw_version == MVPP22) {
+ err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(40));
+ if (err)
+ goto err_mg_clk;
+ /* Sadly, the BM pools all share the same register to
+ * store the high 32 bits of their address. So they
+ * must all have the same high 32 bits, which forces
+ * us to restrict coherent memory to DMA_BIT_MASK(32).
+ */
+ err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
+ if (err)
+ goto err_mg_clk;
+ }
+
/* Initialize network controller */
err = mvpp2_init(pdev, priv);
if (err < 0) {
--
2.14.1
From: Mohammed Shafi Shajakhan <[email protected]>
[ Upstream commit c73f8c00330f59ce9b1ace9ff698aca83390d358 ]
Doing a channel switch via hostapd_cli seems to update
the new channel context for each VAP's appropriately as below
in 'ath10k_mac_update_vif_chan', hence we can safely suppress the
warning that shows up during this operation and dump the warning only
if no vaps are available for channel switch
hostapd_cli -i wlan0 chan_switch 5 5200
OK
ath10k_pci : mac chanctx switch n_vifs 3 mode 1
ath10k_pci : mac chanctx switch vdev_id 2 freq 5180->5200 width 0->0
ath10k_pci : mac chanctx switch vdev_id 1 freq 5180->5200 width 0->0
ath10k_pci : mac chanctx switch vdev_id 0 freq 5180->5200 width 0->0
Call Trace:
WARNING: backports-20161201-3.14.77-9ab3068/drivers/net/wireless/ath/ath10k/mac.c:7126
[<c022f2d4>] (warn_slowpath_null) from [<bf7f150c>]
(ath10k_reconfig_complete+0xe4/0x25c [ath10k_core])
[<bf7f150c>] (ath10k_reconfig_complete [ath10k_core])
[<bf7f35f0>] (ath10k_mac_vif_ap_csa_work+0x214/0x370 [ath10k_core])
[<bf7f38b8>] (ath10k_mac_op_change_chanctx+0x108/0x128 [ath10k_core])
[<bf782ac0>] (ieee80211_recalc_chanctx_min_def+0x30c/0x430 [mac80211])
[<bf7830a4>] (ieee80211_recalc_smps_chanctx+0x2ec/0x840 [mac80211])
[<bf7843e8>] (ieee80211_vif_use_reserved_context+0x7c/0xf8 [mac80211])
[<bf7843e8>] (ieee80211_vif_use_reserved_context [mac80211])
[<bf76e5d4>] (ieee80211_csa_finalize_work+0x5c/0x88 [mac80211])
Fixes: d7bf4b4aba05 ("ath10k: fix ar->rx_channel updating logic")
Signed-off-by: Mohammed Shafi Shajakhan <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/ath/ath10k/mac.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 17ab8efdac35..696b90270615 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -7070,7 +7070,7 @@ ath10k_mac_update_rx_channel(struct ath10k *ar,
lockdep_assert_held(&ar->data_lock);
WARN_ON(ctx && vifs);
- WARN_ON(vifs && n_vifs != 1);
+ WARN_ON(vifs && !n_vifs);
/* FIXME: Sort of an optimization and a workaround. Peers and vifs are
* on a linked list now. Doing a lookup peer -> vif -> chanctx for each
--
2.14.1
From: Geert Uytterhoeven <[email protected]>
[ Upstream commit a0504f0880c11da301dc2b5a5135bd02376e367e ]
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 7c4163aae3d8e5b9 ("ARM: dts: r8a7792: initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/r8a7792.dtsi | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index 713141d38b3e..0b50c6766867 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -58,9 +58,8 @@
next-level-cache = <&L2_CA15>;
};
- L2_CA15: cache-controller@0 {
+ L2_CA15: cache-controller-0 {
compatible = "cache";
- reg = <0>;
cache-unified;
cache-level = <2>;
power-domains = <&sysc R8A7792_PD_CA15_SCU>;
--
2.14.1
From: Chen-Yu Tsai <[email protected]>
[ Upstream commit 9d56defb44b15427f4342c543a70fb7886fc06f5 ]
The master bind function calls numerous drm functions which initialize
underlying structures. It also tries to bind the various components
of the display pipeline, some of which may add additional drm objects.
This patch adds proper cleanup functions in the error path of the
master bind function.
This requires the patch "drm/sun4i: Move drm_mode_config_cleanup call
to main driver", which splits out drm_mode_config_cleanup from
sun4i_framebuffer_free so we can call it separately.
Signed-off-by: Chen-Yu Tsai <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/gpu/drm/sun4i/sun4i_drv.c | 16 +++++++++++-----
1 file changed, 11 insertions(+), 5 deletions(-)
diff --git a/drivers/gpu/drm/sun4i/sun4i_drv.c b/drivers/gpu/drm/sun4i/sun4i_drv.c
index 1feec34ca9dd..9e77fc034e0a 100644
--- a/drivers/gpu/drm/sun4i/sun4i_drv.c
+++ b/drivers/gpu/drm/sun4i/sun4i_drv.c
@@ -145,7 +145,7 @@ static int sun4i_drv_bind(struct device *dev)
ret = component_bind_all(drm->dev, drm);
if (ret) {
dev_err(drm->dev, "Couldn't bind all pipelines components\n");
- goto free_drm;
+ goto cleanup_mode_config;
}
/* Create our layers */
@@ -153,7 +153,7 @@ static int sun4i_drv_bind(struct device *dev)
if (IS_ERR(drv->layers)) {
dev_err(drm->dev, "Couldn't create the planes\n");
ret = PTR_ERR(drv->layers);
- goto free_drm;
+ goto cleanup_mode_config;
}
/* Create our CRTC */
@@ -161,7 +161,7 @@ static int sun4i_drv_bind(struct device *dev)
if (!drv->crtc) {
dev_err(drm->dev, "Couldn't create the CRTC\n");
ret = -EINVAL;
- goto free_drm;
+ goto cleanup_mode_config;
}
drm->irq_enabled = true;
@@ -173,7 +173,7 @@ static int sun4i_drv_bind(struct device *dev)
if (IS_ERR(drv->fbdev)) {
dev_err(drm->dev, "Couldn't create our framebuffer\n");
ret = PTR_ERR(drv->fbdev);
- goto free_drm;
+ goto cleanup_mode_config;
}
/* Enable connectors polling */
@@ -181,10 +181,16 @@ static int sun4i_drv_bind(struct device *dev)
ret = drm_dev_register(drm, 0);
if (ret)
- goto free_drm;
+ goto finish_poll;
return 0;
+finish_poll:
+ drm_kms_helper_poll_fini(drm);
+ sun4i_framebuffer_free(drm);
+cleanup_mode_config:
+ drm_mode_config_cleanup(drm);
+ drm_vblank_cleanup(drm);
free_drm:
drm_dev_unref(drm);
return ret;
--
2.14.1
From: Geert Uytterhoeven <[email protected]>
[ Upstream commit 57a4fd420c6e8a04b6a87ff24d34250cd7c48f15 ]
The Cortex-A57 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 1561f20760ec96db ("arm64: dts: r8a7796: Add Renesas R8A7796 SoC support")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm64/boot/dts/renesas/r8a7796.dtsi | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 9217da983525..53d03cb144e4 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -36,9 +36,8 @@
enable-method = "psci";
};
- L2_CA57: cache-controller@0 {
+ L2_CA57: cache-controller-0 {
compatible = "cache";
- reg = <0>;
power-domains = <&sysc R8A7796_PD_CA57_SCU>;
cache-unified;
cache-level = <2>;
--
2.14.1
From: Chen-Yu Tsai <[email protected]>
[ Upstream commit 4c7f16d14a33a9cfb4af9cb780d8a73bcca64a92 ]
The TCON driver calls sun4i_tcon_init_regmap and sun4i_tcon_init_clocks
in its bind function. The former creates a regmap and writes to several
register to clear its configuration to a known default. The latter
initializes various clocks. This includes enabling the bus clock for
register access and creating the dotclock.
In order for the first step's writes to work, the bus clock must be
enabled which is done in the second step. but the dotclock's ops use
the regmap created in the first step.
Rearrange the function calls such that the clocks are initialized before
the regmap, and split out the dot clock creation to after the regmap is
initialized.
Fixes: 9026e0d122ac ("drm: Add Allwinner A10 Display Engine support")
Signed-off-by: Chen-Yu Tsai <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/gpu/drm/sun4i/sun4i_tcon.c | 22 +++++++++++++++-------
1 file changed, 15 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.c b/drivers/gpu/drm/sun4i/sun4i_tcon.c
index c6afb2448655..f2975a1525be 100644
--- a/drivers/gpu/drm/sun4i/sun4i_tcon.c
+++ b/drivers/gpu/drm/sun4i/sun4i_tcon.c
@@ -336,12 +336,11 @@ static int sun4i_tcon_init_clocks(struct device *dev,
}
}
- return sun4i_dclk_create(dev, tcon);
+ return 0;
}
static void sun4i_tcon_free_clocks(struct sun4i_tcon *tcon)
{
- sun4i_dclk_free(tcon);
clk_disable_unprepare(tcon->clk);
}
@@ -506,22 +505,28 @@ static int sun4i_tcon_bind(struct device *dev, struct device *master,
return ret;
}
+ ret = sun4i_tcon_init_clocks(dev, tcon);
+ if (ret) {
+ dev_err(dev, "Couldn't init our TCON clocks\n");
+ goto err_assert_reset;
+ }
+
ret = sun4i_tcon_init_regmap(dev, tcon);
if (ret) {
dev_err(dev, "Couldn't init our TCON regmap\n");
- goto err_assert_reset;
+ goto err_free_clocks;
}
- ret = sun4i_tcon_init_clocks(dev, tcon);
+ ret = sun4i_dclk_create(dev, tcon);
if (ret) {
- dev_err(dev, "Couldn't init our TCON clocks\n");
- goto err_assert_reset;
+ dev_err(dev, "Couldn't create our TCON dot clock\n");
+ goto err_free_clocks;
}
ret = sun4i_tcon_init_irq(dev, tcon);
if (ret) {
dev_err(dev, "Couldn't init our TCON interrupts\n");
- goto err_free_clocks;
+ goto err_free_dotclock;
}
ret = sun4i_rgb_init(drm);
@@ -530,6 +535,8 @@ static int sun4i_tcon_bind(struct device *dev, struct device *master,
return 0;
+err_free_dotclock:
+ sun4i_dclk_free(tcon);
err_free_clocks:
sun4i_tcon_free_clocks(tcon);
err_assert_reset:
@@ -542,6 +549,7 @@ static void sun4i_tcon_unbind(struct device *dev, struct device *master,
{
struct sun4i_tcon *tcon = dev_get_drvdata(dev);
+ sun4i_dclk_free(tcon);
sun4i_tcon_free_clocks(tcon);
}
--
2.14.1
From: Colin Ian King <[email protected]>
[ Upstream commit 6cc0c259d034c6ab48f4e12f505213988e73d380 ]
Add a sanity check that wid.val has been allocated, fixes a null
pointer deference on stamac when calling ether_add_copy.
Detected by CoverityScan, CID#1369537 ("Dereference null return value")
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/staging/wilc1000/host_interface.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/staging/wilc1000/host_interface.c b/drivers/staging/wilc1000/host_interface.c
index 6ab7443eabde..6326375b76ab 100644
--- a/drivers/staging/wilc1000/host_interface.c
+++ b/drivers/staging/wilc1000/host_interface.c
@@ -1930,6 +1930,8 @@ static s32 Handle_Get_InActiveTime(struct wilc_vif *vif,
wid.type = WID_STR;
wid.size = ETH_ALEN;
wid.val = kmalloc(wid.size, GFP_KERNEL);
+ if (!wid.val)
+ return -ENOMEM;
stamac = wid.val;
memcpy(stamac, strHostIfStaInactiveT->mac, ETH_ALEN);
--
2.14.1
From: Geert Uytterhoeven <[email protected]>
[ Upstream commit 65d0b7ed40f8a3a41a0ac5ed5ca4d1874c6aaf2d ]
The Cortex-A7 cache controller is an integrated controller, and thus the
device node representing it should not have a unit-addresses or reg
property.
Fixes: 34ea4b4a827b4ee7 ("ARM: dts: r8a7794: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/r8a7794.dtsi | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index 7e860d3737ff..6c0150dcf146 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -56,9 +56,8 @@
next-level-cache = <&L2_CA7>;
};
- L2_CA7: cache-controller@0 {
+ L2_CA7: cache-controller-0 {
compatible = "cache";
- reg = <0>;
power-domains = <&sysc R8A7794_PD_CA7_SCU>;
cache-unified;
cache-level = <2>;
--
2.14.1
From: Gabriel Krisman Bertazi <[email protected]>
[ Upstream commit 861078381ba56b56808113736000d9e7ead349c8 ]
If fbdev emulation is disabled, the QXL shutdown path will try to clean
a framebuffer that wasn't initialized, hitting the Oops below. The
problem is that even when FBDEV_EMULATION is disabled we allocate the
qfbdev strutucture, but we don't initialize it. The fix is to stop
allocating the memory, since it won't be used. This allows the existing
verification in the cleanup hook to do it's job preventing the oops.
Now that we don't allocate the unused fbdev structure, we need to be
careful when dereferencing it in the PM suspend hook.
[ 24.284684] BUG: unable to handle kernel NULL pointer dereference at 00000000000002e0
[ 24.285627] IP: mutex_lock+0x18/0x30
[ 24.286049] PGD 78cdf067
[ 24.286050] PUD 7940f067
[ 24.286344] PMD 0
[ 24.286649]
[ 24.287072] Oops: 0002 [#1] SMP
[ 24.287422] Modules linked in: qxl
[ 24.287806] CPU: 0 PID: 2328 Comm: bash Not tainted 4.10.0-rc5+ #97
[ 24.288515] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.3-20161025_171302-gandalf 04/01/2014
[ 24.289681] task: ffff88007c4c0000 task.stack: ffffc90001b58000
[ 24.290354] RIP: 0010:mutex_lock+0x18/0x30
[ 24.290812] RSP: 0018:ffffc90001b5bcb0 EFLAGS: 00010246
[ 24.291401] RAX: 0000000000000000 RBX: 00000000000002e0 RCX: 0000000000000000
[ 24.292209] RDX: ffff88007c4c0000 RSI: 0000000000000001 RDI: 00000000000002e0
[ 24.292987] RBP: ffffc90001b5bcb8 R08: fffffffffffffffe R09: 0000000000000001
[ 24.293797] R10: ffff880078d80b80 R11: 0000000000011400 R12: 0000000000000000
[ 24.294601] R13: 00000000000002e0 R14: ffffffffa0009c28 R15: 0000000000000060
[ 24.295439] FS: 00007f30e3acbb40(0000) GS:ffff88007fc00000(0000) knlGS:0000000000000000
[ 24.296364] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 24.296997] CR2: 00000000000002e0 CR3: 0000000078c7b000 CR4: 00000000000006f0
[ 24.297813] Call Trace:
[ 24.298097] drm_framebuffer_cleanup+0x1f/0x70
[ 24.298612] qxl_fbdev_fini+0x68/0x90 [qxl]
[ 24.299074] qxl_modeset_fini+0xd/0x30 [qxl]
[ 24.299562] qxl_pci_remove+0x22/0x50 [qxl]
[ 24.300025] pci_device_remove+0x34/0xb0
[ 24.300507] device_release_driver_internal+0x150/0x200
[ 24.301082] device_release_driver+0xd/0x10
[ 24.301587] unbind_store+0x108/0x150
[ 24.301993] drv_attr_store+0x20/0x30
[ 24.302402] sysfs_kf_write+0x32/0x40
[ 24.302827] kernfs_fop_write+0x108/0x190
[ 24.303269] __vfs_write+0x23/0x120
[ 24.303678] ? security_file_permission+0x36/0xb0
[ 24.304193] ? rw_verify_area+0x49/0xb0
[ 24.304636] vfs_write+0xb0/0x190
[ 24.305004] SyS_write+0x41/0xa0
[ 24.305362] entry_SYSCALL_64_fastpath+0x1a/0xa9
[ 24.305887] RIP: 0033:0x7f30e31d9620
[ 24.306285] RSP: 002b:00007ffc54b47e68 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 24.307128] RAX: ffffffffffffffda RBX: 00007f30e3497600 RCX: 00007f30e31d9620
[ 24.307928] RDX: 000000000000000d RSI: 0000000000da2008 RDI: 0000000000000001
[ 24.308727] RBP: 000000000070bc60 R08: 00007f30e3498760 R09: 00007f30e3acbb40
[ 24.309504] R10: 0000000000000073 R11: 0000000000000246 R12: 0000000000000001
[ 24.310295] R13: 0000000000000000 R14: 0000000000000000 R15: 00007ffc54b47f34
[ 24.311095] Code: 0e 01 e9 7b fe ff ff 66 90 66 2e 0f 1f 84 00 00 00 00 00
55 48 89 e5 53 48 89 fb e8 83 e8 ff ff 65 48 8b 14 25 40 c4 00 00 31 c0 <3e>
48 0f b1 13 48 85 c0 74 08 48 89 df e8 66 fd ff ff 5b 5d c3
[ 24.313182] RIP: mutex_lock+0x18/0x30 RSP: ffffc90001b5bcb0
[ 24.313811] CR2: 00000000000002e0
[ 24.314208] ---[ end trace 29669c1593cae14b ]---
Signed-off-by: Gabriel Krisman Bertazi <[email protected]>
Link: http://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Gerd Hoffmann <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/gpu/drm/qxl/qxl_fb.c | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/qxl/qxl_fb.c b/drivers/gpu/drm/qxl/qxl_fb.c
index 2cd879a4ae15..cdbb6e625f05 100644
--- a/drivers/gpu/drm/qxl/qxl_fb.c
+++ b/drivers/gpu/drm/qxl/qxl_fb.c
@@ -387,9 +387,11 @@ static const struct drm_fb_helper_funcs qxl_fb_helper_funcs = {
int qxl_fbdev_init(struct qxl_device *qdev)
{
+ int ret = 0;
+
+#ifdef CONFIG_DRM_FBDEV_EMULATION
struct qxl_fbdev *qfbdev;
int bpp_sel = 32; /* TODO: parameter from somewhere? */
- int ret;
qfbdev = kzalloc(sizeof(struct qxl_fbdev), GFP_KERNEL);
if (!qfbdev)
@@ -423,6 +425,8 @@ fini:
drm_fb_helper_fini(&qfbdev->helper);
free:
kfree(qfbdev);
+#endif
+
return ret;
}
@@ -438,6 +442,9 @@ void qxl_fbdev_fini(struct qxl_device *qdev)
void qxl_fbdev_set_suspend(struct qxl_device *qdev, int state)
{
+ if (!qdev->mode_info.qfbdev)
+ return;
+
drm_fb_helper_set_suspend(&qdev->mode_info.qfbdev->helper, state);
}
--
2.14.1
From: "Naveen N. Rao" <[email protected]>
[ Upstream commit 90ec5e89e393c76e19afc845d8f88a5dc8315919 ]
kretprobes can be registered by specifying an absolute address or by
specifying offset to a symbol. However, we need to ensure this falls at
function entry so as to be able to determine the return address.
Validate the same during kretprobe registration. By default, there
should not be any offset from a function entry, as determined through a
kallsyms_lookup(). Introduce arch_function_offset_within_entry() as a
way for architectures to override this.
Signed-off-by: Naveen N. Rao <[email protected]>
Acked-by: Masami Hiramatsu <[email protected]>
Cc: Ananth N Mavinakayanahalli <[email protected]>
Cc: Michael Ellerman <[email protected]>
Cc: Steven Rostedt <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/f1583bc4839a3862cfc2acefcc56f9c8837fa2ba.1487770934.git.naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
include/linux/kprobes.h | 1 +
kernel/kprobes.c | 13 +++++++++++++
2 files changed, 14 insertions(+)
diff --git a/include/linux/kprobes.h b/include/linux/kprobes.h
index e23392517db9..56a998f34bdd 100644
--- a/include/linux/kprobes.h
+++ b/include/linux/kprobes.h
@@ -266,6 +266,7 @@ extern int arch_init_kprobes(void);
extern void show_registers(struct pt_regs *regs);
extern void kprobes_inc_nmissed_count(struct kprobe *p);
extern bool arch_within_kprobe_blacklist(unsigned long addr);
+extern bool arch_function_offset_within_entry(unsigned long offset);
extern bool within_kprobe_blacklist(unsigned long addr);
diff --git a/kernel/kprobes.c b/kernel/kprobes.c
index a1a07cf1101f..2ede39e4227f 100644
--- a/kernel/kprobes.c
+++ b/kernel/kprobes.c
@@ -1834,12 +1834,25 @@ static int pre_handler_kretprobe(struct kprobe *p, struct pt_regs *regs)
}
NOKPROBE_SYMBOL(pre_handler_kretprobe);
+bool __weak arch_function_offset_within_entry(unsigned long offset)
+{
+ return !offset;
+}
+
int register_kretprobe(struct kretprobe *rp)
{
int ret = 0;
struct kretprobe_instance *inst;
int i;
void *addr;
+ unsigned long offset;
+
+ addr = kprobe_addr(&rp->kp);
+ if (!kallsyms_lookup_size_offset((unsigned long)addr, NULL, &offset))
+ return -EINVAL;
+
+ if (!arch_function_offset_within_entry(offset))
+ return -EINVAL;
if (kretprobe_blacklist_size) {
addr = kprobe_addr(&rp->kp);
--
2.14.1
From: Varsha Rao <[email protected]>
[ Upstream commit d351c2db5420bb17dcd2d9aac7ddb5f64c6d04b3 ]
BUG_ON() is replaced with WARN_ON() and EINVAL is returned, when
WARN_ON() is true. This fixes the following checkpatch issue:
Avoid crashing the kernel - try using WARN_ON & recovery code rather
than BUG() or BUG_ON().
Signed-off-by: Varsha Rao <[email protected]>
Reviewed-by: Samuel Thibault <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/staging/speakup/kobjects.c | 8 ++++++--
1 file changed, 6 insertions(+), 2 deletions(-)
diff --git a/drivers/staging/speakup/kobjects.c b/drivers/staging/speakup/kobjects.c
index e744aa9730ff..dea018cba094 100644
--- a/drivers/staging/speakup/kobjects.c
+++ b/drivers/staging/speakup/kobjects.c
@@ -834,7 +834,9 @@ static ssize_t message_show(struct kobject *kobj,
struct msg_group_t *group = spk_find_msg_group(attr->attr.name);
unsigned long flags;
- BUG_ON(!group);
+ if (WARN_ON(!group))
+ return -EINVAL;
+
spin_lock_irqsave(&speakup_info.spinlock, flags);
retval = message_show_helper(buf, group->start, group->end);
spin_unlock_irqrestore(&speakup_info.spinlock, flags);
@@ -846,7 +848,9 @@ static ssize_t message_store(struct kobject *kobj, struct kobj_attribute *attr,
{
struct msg_group_t *group = spk_find_msg_group(attr->attr.name);
- BUG_ON(!group);
+ if (WARN_ON(!group))
+ return -EINVAL;
+
return message_store_helper(buf, count, group);
}
--
2.14.1
From: Borislav Petkov <[email protected]>
[ Upstream commit 02d492e5dcb72c004d213756eb87c9d62a6d76a7 ]
When using perf stat on an AMD F15h system with the default hw events
attributes, some of the events don't get counted:
Performance counter stats for 'sleep 1':
0.749208 task-clock (msec) # 0.001 CPUs utilized
1 context-switches # 0.001 M/sec
0 cpu-migrations # 0.000 K/sec
54 page-faults # 0.072 M/sec
1,122,815 cycles # 1.499 GHz
286,740 stalled-cycles-frontend # 25.54% frontend cycles idle
<not counted> stalled-cycles-backend (0.00%)
^^^^^^^^^^^^
<not counted> instructions (0.00%)
^^^^^^^^^^^^
<not counted> branches (0.00%)
<not counted> branch-misses (0.00%)
1.001550070 seconds time elapsed
The reason is that we have the HW watchdog consuming one PMU counter and
when perf tries to schedule 6 events on 6 counters and some of those
counters are constrained to only a specific subset of PMCs by the
hardware, the event scheduling fails.
So issue a hint to disable the HW watchdog around a perf stat session.
Committer note:
Testing it...
# perf stat -d usleep 1
Performance counter stats for 'usleep 1':
1.180203 task-clock (msec) # 0.490 CPUs utilized
1 context-switches # 0.847 K/sec
0 cpu-migrations # 0.000 K/sec
54 page-faults # 0.046 M/sec
184,754 cycles # 0.157 GHz
714,553 instructions # 3.87 insn per cycle
154,661 branches # 131.046 M/sec
7,247 branch-misses # 4.69% of all branches
219,984 L1-dcache-loads # 186.395 M/sec
17,600 L1-dcache-load-misses # 8.00% of all L1-dcache hits (90.16%)
<not counted> LLC-loads (0.00%)
<not counted> LLC-load-misses (0.00%)
0.002406823 seconds time elapsed
Some events weren't counted. Try disabling the NMI watchdog:
echo 0 > /proc/sys/kernel/nmi_watchdog
perf stat ...
echo 1 > /proc/sys/kernel/nmi_watchdog
#
Signed-off-by: Borislav Petkov <[email protected]>
Acked-by: Ingo Molnar <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Robert Richter <[email protected]>
Cc: Vince Weaver <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/perf/builtin-stat.c | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/tools/perf/builtin-stat.c b/tools/perf/builtin-stat.c
index 688dea7cb08f..c241167c76c9 100644
--- a/tools/perf/builtin-stat.c
+++ b/tools/perf/builtin-stat.c
@@ -146,6 +146,7 @@ static aggr_get_id_t aggr_get_id;
static bool append_file;
static const char *output_name;
static int output_fd;
+static int print_free_counters_hint;
struct perf_stat {
bool record;
@@ -1109,6 +1110,9 @@ static void printout(int id, int nr, struct perf_evsel *counter, double uval,
counter->supported ? CNTR_NOT_COUNTED : CNTR_NOT_SUPPORTED,
csv_sep);
+ if (counter->supported)
+ print_free_counters_hint = 1;
+
fprintf(stat_config.output, "%-*s%s",
csv_output ? 0 : unit_width,
counter->unit, csv_sep);
@@ -1477,6 +1481,13 @@ static void print_footer(void)
avg_stats(&walltime_nsecs_stats));
}
fprintf(output, "\n\n");
+
+ if (print_free_counters_hint)
+ fprintf(output,
+"Some events weren't counted. Try disabling the NMI watchdog:\n"
+" echo 0 > /proc/sys/kernel/nmi_watchdog\n"
+" perf stat ...\n"
+" echo 1 > /proc/sys/kernel/nmi_watchdog\n");
}
static void print_counters(struct timespec *ts, int argc, const char **argv)
--
2.14.1
From: Jonas Gorski <[email protected]>
[ Upstream commit ccd0657c33b2c3701c5b14725284b7e671d3fb93 ]
Fix compilation by renaming argument dev to spi as expected by the code.
Fixes the following error:
drivers/spi/spi-bcm63xx.c: In function ‘bcm63xx_spi_max_length’:
drivers/spi/spi-bcm63xx.c:434:50: error: ‘spi’ undeclared (first use in this function)
struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
^~~
Fixes: 0135c03df914 ("spi/bcm63xx: make spi subsystem aware of message size limits")
Signed-off-by: Jonas Gorski <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/spi/spi-bcm63xx.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/spi/spi-bcm63xx.c b/drivers/spi/spi-bcm63xx.c
index caa733ec405c..7ee4b04a4a11 100644
--- a/drivers/spi/spi-bcm63xx.c
+++ b/drivers/spi/spi-bcm63xx.c
@@ -428,7 +428,7 @@ static irqreturn_t bcm63xx_spi_interrupt(int irq, void *dev_id)
return IRQ_HANDLED;
}
-static size_t bcm63xx_spi_max_length(struct spi_device *dev)
+static size_t bcm63xx_spi_max_length(struct spi_device *spi)
{
struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
--
2.14.1
From: Valtteri Heikkilä <[email protected]>
[ Upstream commit 3f3752705dbd50b66b66ad7b4d54fe33d2f746ed ]
This patch fixes an issue in drivers/hid/hid-input.c where USB HID
control null state flag is not checked upon rejecting inputs outside
logical minimum-maximum range. The check should be made according to USB
HID specification 1.11, section 6.2.2.5, p.31. The fix will resolve
issues with some game controllers, such as:
https://bugzilla.kernel.org/show_bug.cgi?id=68621
[[email protected]: shortened and fixed spelling in commit message]
Signed-off-by: Valtteri Heikkilä <[email protected]>
Signed-off-by: Tomasz Kramkowski <[email protected]>
Acked-By: Benjamin Tissoires <[email protected]>
Signed-off-by: Jiri Kosina <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/hid/hid-input.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/hid/hid-input.c b/drivers/hid/hid-input.c
index fb9ace1cef8b..76f2527fbc60 100644
--- a/drivers/hid/hid-input.c
+++ b/drivers/hid/hid-input.c
@@ -1156,6 +1156,7 @@ void hidinput_hid_event(struct hid_device *hid, struct hid_field *field, struct
* don't specify logical min and max.
*/
if ((field->flags & HID_MAIN_ITEM_VARIABLE) &&
+ (field->flags & HID_MAIN_ITEM_NULL_STATE) &&
(field->logical_minimum < field->logical_maximum) &&
(value < field->logical_minimum ||
value > field->logical_maximum)) {
--
2.14.1
From: Jonas Gorski <[email protected]>
[ Upstream commit 0135c03df914f0481c61f097c78d37cece84f330 ]
The bcm63xx SPI controller does not allow manual control of the CS
lines and will toggle it automatically before and after sending data,
so we are limited to messages that fit in the FIFO buffer. Since the CS
lines aren't available as GPIOs either, we will need to make slave
drivers aware of this limitation so they can handle them accordingly.
Signed-off-by: Jonas Gorski <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/spi/spi-bcm63xx.c | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/drivers/spi/spi-bcm63xx.c b/drivers/spi/spi-bcm63xx.c
index fee747030ee6..caa733ec405c 100644
--- a/drivers/spi/spi-bcm63xx.c
+++ b/drivers/spi/spi-bcm63xx.c
@@ -428,6 +428,13 @@ static irqreturn_t bcm63xx_spi_interrupt(int irq, void *dev_id)
return IRQ_HANDLED;
}
+static size_t bcm63xx_spi_max_length(struct spi_device *dev)
+{
+ struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
+
+ return bs->fifo_size;
+}
+
static const unsigned long bcm6348_spi_reg_offsets[] = {
[SPI_CMD] = SPI_6348_CMD,
[SPI_INT_STATUS] = SPI_6348_INT_STATUS,
@@ -541,6 +548,8 @@ static int bcm63xx_spi_probe(struct platform_device *pdev)
master->transfer_one_message = bcm63xx_spi_transfer_one;
master->mode_bits = MODEBITS;
master->bits_per_word_mask = SPI_BPW_MASK(8);
+ master->max_transfer_size = bcm63xx_spi_max_length;
+ master->max_message_size = bcm63xx_spi_max_length;
master->auto_runtime_pm = true;
bs->msg_type_shift = bs->reg_offsets[SPI_MSG_TYPE_SHIFT];
bs->msg_ctl_width = bs->reg_offsets[SPI_MSG_CTL_WIDTH];
--
2.14.1
Hello, Sasha!
Following 2 patches must be applied together with the patch:
5e0a39d0f727b35c8b7ef56ba0724c8ceb006297 clocksource/drivers/rockchip_timer: Implement clocksource timer
627988a66aee3c845aa2f1f874a3ddba8adb89d9 ARM: dts: rockchip: Add timer entries to rk3188 SoC
Alexander.
> 4 марта 2018 г., в 1:29, Sasha Levin <[email protected]> написал(а):
>
> From: Alexander Kochetkov <[email protected]>
>
> [ Upstream commit 500d0aa918a2ea6bb918fee8adcf27dc2912bcd1 ]
>
> The clocksource and the sched_clock provided by the arm_global_timer
> are quite unstable because their rates depend on the cpu frequency.
>
> On the other side, the arm_global_timer has a higher rating than the
> rockchip_timer, it will be selected by default by the time framework
> while we want to use the stable rockchip clocksource.
>
> Let's disable the arm_global_timer in order to have the rockchip
> clocksource selected by default.
>
> Signed-off-by: Alexander Kochetkov <[email protected]>
> Signed-off-by: Daniel Lezcano <[email protected]>
> Reviewed-by: Heiko Stuebner <[email protected]>
> Signed-off-by: Sasha Levin <[email protected]>
> ---
> arch/arm/boot/dts/rk3188.dtsi | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/arch/arm/boot/dts/rk3188.dtsi b/arch/arm/boot/dts/rk3188.dtsi
> index 31f81b265cef..73a200914f0b 100644
> --- a/arch/arm/boot/dts/rk3188.dtsi
> +++ b/arch/arm/boot/dts/rk3188.dtsi
> @@ -530,6 +530,7 @@
>
> &global_timer {
> interrupts = <GIC_PPI 11 0xf04>;
> + status = "disabled";
> };
>
> &local_timer {
> --
> 2.14.1
Hi Sasha,
Sasha Levin wrote:
> From: "Naveen N. Rao" <[email protected]>
>
> [ Upstream commit 90ec5e89e393c76e19afc845d8f88a5dc8315919 ]
>
Sorry if this is obvious, but why was this patch picked up for -stable?
I don't see the upstream commit tagging -stable, so curious why this was
done.
I don't think this patch should be pushed to -stable since this is not
really a bug fix. There are also other dependencies for this change (see
commit a64e3f35a45f4a, for instance), including how userspace (perf)
builds out the retprobe argument. As such, please drop this from -stable
(for 3.18. 4.4 and 4.9).
Thanks,
Naveen
On Sat, Mar 03, 2018 at 10:27:56PM +0000, Sasha Levin wrote:
> From: Jonas Gorski <[email protected]>
>
> [ Upstream commit 0135c03df914f0481c61f097c78d37cece84f330 ]
Why are there so many more patches for v4.9 than for more recent
kernels?
> The bcm63xx SPI controller does not allow manual control of the CS
> lines and will toggle it automatically before and after sending data,
> so we are limited to messages that fit in the FIFO buffer. Since the CS
> lines aren't available as GPIOs either, we will need to make slave
> drivers aware of this limitation so they can handle them accordingly.
This seems really aggressive for stable...
On Sat, Mar 03, 2018 at 10:29:00PM +0000, Sasha Levin wrote:
> From: Javier Martinez Canillas <[email protected]>
>
> [ Upstream commit 9ba2da5f5d18daaa365ab5426b05e16f1d114786 ]
>
> The driver doesn't have a struct of_device_id table but supported devices
> are registered via Device Trees. This is working on the assumption that a
> I2C device registered via OF will always match a legacy I2C device ID and
> that the MODALIAS reported will always be of the form i2c:<device>.
>
> But this could change in the future so the correct approach is to have an
> OF device ID table if the devices are registered via OF.
As the commit message itself says this is not fixing anything, it's
defence against future changes.
On Sat, Mar 03, 2018 at 10:29:01PM +0000, Sasha Levin wrote:
> From: Javier Martinez Canillas <[email protected]>
>
> [ Upstream commit 5cf015d9cb02c360582b624497b0a1716881cf28 ]
>
> The driver doesn't have a struct of_device_id table but supported devices
> are registered via Device Trees. This is working on the assumption that a
> I2C device registered via OF will always match a legacy I2C device ID and
> that the MODALIAS reported will always be of the form i2c:<device>.
>
> But this could change in the future so the correct approach is to have an
> OF device ID table if the devices are registered via OF.
Here also.
On Sat, Mar 03, 2018 at 10:29:00PM +0000, Sasha Levin wrote:
> From: Javier Martinez Canillas <[email protected]>
>
> [ Upstream commit 71c314d7ef2442cd798584a3dece8151215e1777 ]
>
> The driver doesn't have a struct of_device_id table but supported devices
> are registered via Device Trees. This is working on the assumption that a
> I2C device registered via OF will always match a legacy I2C device ID and
> that the MODALIAS reported will always be of the form i2c:<device>.
>
> But this could change in the future so the correct approach is to have an
> OF device ID table if the devices are registered via OF.
Same here.
On Mon, Mar 5, 2018 at 11:42 AM, Mark Brown <[email protected]> wrote:
> On Sat, Mar 03, 2018 at 10:29:00PM +0000, Sasha Levin wrote:
>> From: Javier Martinez Canillas <[email protected]>
>>
>> [ Upstream commit 9ba2da5f5d18daaa365ab5426b05e16f1d114786 ]
>>
>> The driver doesn't have a struct of_device_id table but supported devices
>> are registered via Device Trees. This is working on the assumption that a
>> I2C device registered via OF will always match a legacy I2C device ID and
>> that the MODALIAS reported will always be of the form i2c:<device>.
>>
>> But this could change in the future so the correct approach is to have an
>> OF device ID table if the devices are registered via OF.
>
> As the commit message itself says this is not fixing anything, it's
> defence against future changes.
That's correct.
These were just preparatory patches for a change in the I2C subsystem
to properly report OF module aliases [0]. So these will only be
relevant once [0] is merged, but that patch will never be backported
to a stable kernel.
[0]: https://patchwork.kernel.org/patch/10089425/
Best regards,
Javier
On Mon, Mar 05, 2018 at 02:19:42AM +0300, Alexander Kochetkov wrote:
>Hello, Sasha!
>
>Following 2 patches must be applied together with the patch:
>5e0a39d0f727b35c8b7ef56ba0724c8ceb006297 clocksource/drivers/rockchip_timer: Implement clocksource timer
>627988a66aee3c845aa2f1f874a3ddba8adb89d9 ARM: dts: rockchip: Add timer entries to rk3188 SoC
Hey Alexander,
A bit too much for stable, I'll just drop the patch. Thanks!
--
Thanks,
Sasha
On Mon, Mar 05, 2018 at 12:32:57PM +0530, Naveen N. Rao wrote:
>Hi Sasha,
>
>Sasha Levin wrote:
>>From: "Naveen N. Rao" <[email protected]>
>>
>>[ Upstream commit 90ec5e89e393c76e19afc845d8f88a5dc8315919 ]
>>
>
>Sorry if this is obvious, but why was this patch picked up for
>-stable? I don't see the upstream commit tagging -stable, so curious
>why this was done.
>
>I don't think this patch should be pushed to -stable since this is not
>really a bug fix. There are also other dependencies for this change
>(see commit a64e3f35a45f4a, for instance), including how userspace
>(perf) builds out the retprobe argument. As such, please drop this
>from -stable (for 3.18. 4.4 and 4.9).
Hi Naveen,
It's an automatic selection process that attempts to find commits that
should be in stable but weren't tagged as such.
I'll drop this patch, thanks!
--
Thanks,
Sasha
On Mon, Mar 05, 2018 at 10:23:10AM +0000, Mark Brown wrote:
>On Sat, Mar 03, 2018 at 10:27:56PM +0000, Sasha Levin wrote:
>> From: Jonas Gorski <[email protected]>
>>
>> [ Upstream commit 0135c03df914f0481c61f097c78d37cece84f330 ]
>
>Why are there so many more patches for v4.9 than for more recent
>kernels?
The v4.11..v4.14 range got processed, and all those commits are now
being pushed into 4.9 and older.
>> The bcm63xx SPI controller does not allow manual control of the CS
>> lines and will toggle it automatically before and after sending data,
>> so we are limited to messages that fit in the FIFO buffer. Since the CS
>> lines aren't available as GPIOs either, we will need to make slave
>> drivers aware of this limitation so they can handle them accordingly.
>
>This seems really aggressive for stable...
Why so?
--
Thanks,
Sasha
On Mon, Mar 05, 2018 at 10:42:03AM +0000, Mark Brown wrote:
>On Sat, Mar 03, 2018 at 10:29:00PM +0000, Sasha Levin wrote:
>> From: Javier Martinez Canillas <[email protected]>
>>
>> [ Upstream commit 9ba2da5f5d18daaa365ab5426b05e16f1d114786 ]
>>
>> The driver doesn't have a struct of_device_id table but supported devices
>> are registered via Device Trees. This is working on the assumption that a
>> I2C device registered via OF will always match a legacy I2C device ID and
>> that the MODALIAS reported will always be of the form i2c:<device>.
>>
>> But this could change in the future so the correct approach is to have an
>> OF device ID table if the devices are registered via OF.
>
>As the commit message itself says this is not fixing anything, it's
>defence against future changes.
I was under the impression that this refers to future HW changes rather
than code, I'll drop all 3. Thanks!
--
Thanks,
Sasha
On Mon, Mar 05, 2018 at 08:09:29PM +0000, Sasha Levin wrote:
> On Mon, Mar 05, 2018 at 10:42:03AM +0000, Mark Brown wrote:
> >As the commit message itself says this is not fixing anything, it's
> >defence against future changes.
> I was under the impression that this refers to future HW changes rather
> than code, I'll drop all 3. Thanks!
I think there were more than three - I stopped replying after a bunch of
these in the same pattern. ICBW though.
On Mon, Mar 05, 2018 at 08:07:46PM +0000, Sasha Levin wrote:
> On Mon, Mar 05, 2018 at 10:23:10AM +0000, Mark Brown wrote:
> >On Sat, Mar 03, 2018 at 10:27:56PM +0000, Sasha Levin wrote:
> >> The bcm63xx SPI controller does not allow manual control of the CS
> >> lines and will toggle it automatically before and after sending data,
> >> so we are limited to messages that fit in the FIFO buffer. Since the CS
> >> lines aren't available as GPIOs either, we will need to make slave
> >> drivers aware of this limitation so they can handle them accordingly.
> >This seems really aggressive for stable...
> Why so?
It's exposing more capability information but it's in the "how did this
ever work without the fix" range, and I'd worry that this might cause us
to do something like start exercising handling code in client drivers
that had never been tested. Not that I can immediately see any client
drivers in mainline that actually pay attention... :/
On 5 March 2018 at 21:35, Mark Brown <[email protected]> wrote:
> On Mon, Mar 05, 2018 at 08:07:46PM +0000, Sasha Levin wrote:
>> On Mon, Mar 05, 2018 at 10:23:10AM +0000, Mark Brown wrote:
>> >On Sat, Mar 03, 2018 at 10:27:56PM +0000, Sasha Levin wrote:
>
>> >> The bcm63xx SPI controller does not allow manual control of the CS
>> >> lines and will toggle it automatically before and after sending data,
>> >> so we are limited to messages that fit in the FIFO buffer. Since the CS
>> >> lines aren't available as GPIOs either, we will need to make slave
>> >> drivers aware of this limitation so they can handle them accordingly.
>
>> >This seems really aggressive for stable...
>
>> Why so?
>
> It's exposing more capability information but it's in the "how did this
> ever work without the fix" range, and I'd worry that this might cause us
> to do something like start exercising handling code in client drivers
> that had never been tested. Not that I can immediately see any client
> drivers in mainline that actually pay attention... :/
I would assume that most spi client drivers use short messages, so
they aren't affected unless the max message size is really short.
m25p80 on the other hand will do arbitrarily large transfers/reads, so
there it was supported first.
m25p80 supports max_transfer_size since 4,9, and max_message_size
since 4.11 with commit 9e276de6a367cde07c1a63522152985d4e5cca8b. So
that one would need to be backported as well for the max_message_size
being actually meaningful.
tinydrm-helpers also observes max_transfers_size since 4.11 with
commit 9f69eb5c36a644571cca6b2f8dc5f6a7cba04a8b where it was added,
but since this is a larger commit and not just a "bugfix" one, this
doesn't seem like a candidate for backporting.
Regards
Jonas
On Tue, Mar 06, 2018 at 02:42:43PM +0100, Jonas Gorski wrote:
> On 5 March 2018 at 21:35, Mark Brown <[email protected]> wrote:
> > It's exposing more capability information but it's in the "how did this
> > ever work without the fix" range, and I'd worry that this might cause us
> > to do something like start exercising handling code in client drivers
> > that had never been tested. Not that I can immediately see any client
> > drivers in mainline that actually pay attention... :/
> I would assume that most spi client drivers use short messages, so
> they aren't affected unless the max message size is really short.
> m25p80 on the other hand will do arbitrarily large transfers/reads, so
> there it was supported first.
There's a bunch of SPI drivers that do firmware downloads which I'd
expect to be affected, the limit the device has is tiny so it's
relatively easy to bump into it. It's very rare for devices to be so
limited so unfortunately client drivers don't generally check though.
On 6 March 2018 at 15:20, Mark Brown <[email protected]> wrote:
> On Tue, Mar 06, 2018 at 02:42:43PM +0100, Jonas Gorski wrote:
>> On 5 March 2018 at 21:35, Mark Brown <[email protected]> wrote:
>
>> > It's exposing more capability information but it's in the "how did this
>> > ever work without the fix" range, and I'd worry that this might cause us
>> > to do something like start exercising handling code in client drivers
>> > that had never been tested. Not that I can immediately see any client
>> > drivers in mainline that actually pay attention... :/
>
>> I would assume that most spi client drivers use short messages, so
>> they aren't affected unless the max message size is really short.
>> m25p80 on the other hand will do arbitrarily large transfers/reads, so
>> there it was supported first.
>
> There's a bunch of SPI drivers that do firmware downloads which I'd
> expect to be affected, the limit the device has is tiny so it's
> relatively easy to bump into it. It's very rare for devices to be so
> limited so unfortunately client drivers don't generally check though.
Well, at least for bcm63xx it's very rare to have something other than
a flash chip, a (broadcom) ethernet switch management interface, or a
SLIC/SLAC attached to the SPI controller. And AFAICT of these three
only the flash chip uses large SPI transfers. Furthermore, unless you
have a development board, you won't be able to attach anything
different to it. So the chance to bump into the limits with other
drivers is rather low.
I would assume that this is true for most systems with a limited SPI
controller. I would hope that most board designers are sensible enough
to not add devices that won't work ;-)
Regards
Jonas
On Tue, Mar 06, 2018 at 04:33:34PM +0100, Jonas Gorski wrote:
> I would assume that this is true for most systems with a limited SPI
> controller. I would hope that most board designers are sensible enough
> to not add devices that won't work ;-)
With things like firmware downloads the problem is that they can
generally work, they're just horribly inefficient since you have to
chunk them up into multiple operations rather than just pointing the
hardware at a big buffer and letting it get on with things (same problem
as with flash really).
Hi,
On Sun, Mar 4, 2018 at 6:28 AM, Sasha Levin
<[email protected]> wrote:
> From: Chen-Yu Tsai <[email protected]>
>
> [ Upstream commit 68f37d862403e8f95337b2eca90af15d0b8cd5d7 ]
>
> The DDR1 PLL on the A33 is an oddball amongst the A33 CCU clocks.
> It is a clock multiplier, with the effective multiplier in the
> range of 12 ~ 255 and no offset between the multiplier value and
> the value programmed into the register.
>
> Implement the zero offset and minimum value of 12 for this clock.
>
> Fixes: d05c748bd730 ("clk: sunxi-ng: Add A33 CCU support")
> Signed-off-by: Chen-Yu Tsai <[email protected]>
> Signed-off-by: Maxime Ripard <[email protected]>
> Signed-off-by: Sasha Levin <[email protected]>
> ---
> drivers/clk/sunxi-ng/ccu-sun8i-a33.c | 18 +++++++++++-------
> 1 file changed, 11 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-a33.c b/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
> index e1dc4e5b34e1..bdbaf26f551f 100644
> --- a/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
> +++ b/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
> @@ -159,13 +159,17 @@ static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_de_clk, "pll-de",
> BIT(28), /* lock */
> CLK_SET_RATE_UNGATE);
>
> -/* TODO: Fix N */
> -static SUNXI_CCU_N_WITH_GATE_LOCK(pll_ddr1_clk, "pll-ddr1",
> - "osc24M", 0x04c,
> - 8, 6, /* N */
> - BIT(31), /* gate */
> - BIT(28), /* lock */
> - CLK_SET_RATE_UNGATE);
> +static struct ccu_mult pll_ddr1_clk = {
> + .enable = BIT(31),
> + .lock = BIT(28),
As you undoubtedly noticed, this does not build. It needs commit
cf719012b232 ("clk: sunxi-ng: mult: Support PLL lock detection")
to be applied first. They were part of the same series.
Incidentally, how can we note these kinds of dependencies to make
life easier for stable kernel maintainers?
Thanks
ChenYu
> + .mult = _SUNXI_CCU_MULT_OFFSET_MIN_MAX(8, 6, 0, 12, 0),
> + .common = {
> + .reg = 0x04c,
> + .hw.init = CLK_HW_INIT("pll-ddr1", "osc24M",
> + &ccu_mult_ops,
> + CLK_SET_RATE_UNGATE),
> + },
> +};
>
> static const char * const cpux_parents[] = { "osc32k", "osc24M",
> "pll-cpux" , "pll-cpux" };
> --
> 2.14.1
On Tue, Mar 20, 2018 at 11:10:42AM +0800, Chen-Yu Tsai wrote:
>Hi,
>
>On Sun, Mar 4, 2018 at 6:28 AM, Sasha Levin
><[email protected]> wrote:
>> From: Chen-Yu Tsai <[email protected]>
>>
>> [ Upstream commit 68f37d862403e8f95337b2eca90af15d0b8cd5d7 ]
>>
>> The DDR1 PLL on the A33 is an oddball amongst the A33 CCU clocks.
>> It is a clock multiplier, with the effective multiplier in the
>> range of 12 ~ 255 and no offset between the multiplier value and
>> the value programmed into the register.
>>
>> Implement the zero offset and minimum value of 12 for this clock.
>>
>> Fixes: d05c748bd730 ("clk: sunxi-ng: Add A33 CCU support")
>> Signed-off-by: Chen-Yu Tsai <[email protected]>
>> Signed-off-by: Maxime Ripard <[email protected]>
>> Signed-off-by: Sasha Levin <[email protected]>
>> ---
>> drivers/clk/sunxi-ng/ccu-sun8i-a33.c | 18 +++++++++++-------
>> 1 file changed, 11 insertions(+), 7 deletions(-)
>>
>> diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-a33.c b/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
>> index e1dc4e5b34e1..bdbaf26f551f 100644
>> --- a/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
>> +++ b/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
>> @@ -159,13 +159,17 @@ static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_de_clk, "pll-de",
>> BIT(28), /* lock */
>> CLK_SET_RATE_UNGATE);
>>
>> -/* TODO: Fix N */
>> -static SUNXI_CCU_N_WITH_GATE_LOCK(pll_ddr1_clk, "pll-ddr1",
>> - "osc24M", 0x04c,
>> - 8, 6, /* N */
>> - BIT(31), /* gate */
>> - BIT(28), /* lock */
>> - CLK_SET_RATE_UNGATE);
>> +static struct ccu_mult pll_ddr1_clk = {
>> + .enable = BIT(31),
>> + .lock = BIT(28),
>
>As you undoubtedly noticed, this does not build. It needs commit
>cf719012b232 ("clk: sunxi-ng: mult: Support PLL lock detection")
>to be applied first. They were part of the same series.
Thanks for the heads up!
>Incidentally, how can we note these kinds of dependencies to make
>life easier for stable kernel maintainers?
Yes! There are more details in Documentation/process/stable-kernel-rules.rst:
"""
Additionally, some patches submitted via Option 1 may have additional patch
prerequisites which can be cherry-picked. This can be specified in the following
format in the sign-off area:
Cc: <[email protected]> # 3.3.x: a1f84a3: sched: Check for idle
Cc: <[email protected]> # 3.3.x: 1b9508f: sched: Rate-limit newidle
Cc: <[email protected]> # 3.3.x: fd21073: sched: Fix affinity logic
Cc: <[email protected]> # 3.3.x
Signed-off-by: Ingo Molnar <[email protected]>
The tag sequence has the meaning of:
git cherry-pick a1f84a3
git cherry-pick 1b9508f
git cherry-pick fd21073
git cherry-pick <this commit>
"""
--
Thanks,
Sasha
On Thu, Mar 22, 2018 at 12:14 AM, Sasha Levin
<[email protected]> wrote:
> On Tue, Mar 20, 2018 at 11:10:42AM +0800, Chen-Yu Tsai wrote:
>>Hi,
>>
>>On Sun, Mar 4, 2018 at 6:28 AM, Sasha Levin
>><[email protected]> wrote:
>>> From: Chen-Yu Tsai <[email protected]>
>>>
>>> [ Upstream commit 68f37d862403e8f95337b2eca90af15d0b8cd5d7 ]
>>>
>>> The DDR1 PLL on the A33 is an oddball amongst the A33 CCU clocks.
>>> It is a clock multiplier, with the effective multiplier in the
>>> range of 12 ~ 255 and no offset between the multiplier value and
>>> the value programmed into the register.
>>>
>>> Implement the zero offset and minimum value of 12 for this clock.
>>>
>>> Fixes: d05c748bd730 ("clk: sunxi-ng: Add A33 CCU support")
>>> Signed-off-by: Chen-Yu Tsai <[email protected]>
>>> Signed-off-by: Maxime Ripard <[email protected]>
>>> Signed-off-by: Sasha Levin <[email protected]>
>>> ---
>>> drivers/clk/sunxi-ng/ccu-sun8i-a33.c | 18 +++++++++++-------
>>> 1 file changed, 11 insertions(+), 7 deletions(-)
>>>
>>> diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-a33.c b/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
>>> index e1dc4e5b34e1..bdbaf26f551f 100644
>>> --- a/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
>>> +++ b/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
>>> @@ -159,13 +159,17 @@ static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_de_clk, "pll-de",
>>> BIT(28), /* lock */
>>> CLK_SET_RATE_UNGATE);
>>>
>>> -/* TODO: Fix N */
>>> -static SUNXI_CCU_N_WITH_GATE_LOCK(pll_ddr1_clk, "pll-ddr1",
>>> - "osc24M", 0x04c,
>>> - 8, 6, /* N */
>>> - BIT(31), /* gate */
>>> - BIT(28), /* lock */
>>> - CLK_SET_RATE_UNGATE);
>>> +static struct ccu_mult pll_ddr1_clk = {
>>> + .enable = BIT(31),
>>> + .lock = BIT(28),
>>
>>As you undoubtedly noticed, this does not build. It needs commit
>>cf719012b232 ("clk: sunxi-ng: mult: Support PLL lock detection")
>>to be applied first. They were part of the same series.
>
> Thanks for the heads up!
>
>>Incidentally, how can we note these kinds of dependencies to make
>>life easier for stable kernel maintainers?
>
> Yes! There are more details in Documentation/process/stable-kernel-rules.rst:
>
>
> """
> Additionally, some patches submitted via Option 1 may have additional patch
> prerequisites which can be cherry-picked. This can be specified in the following
> format in the sign-off area:
>
> Cc: <[email protected]> # 3.3.x: a1f84a3: sched: Check for idle
> Cc: <[email protected]> # 3.3.x: 1b9508f: sched: Rate-limit newidle
> Cc: <[email protected]> # 3.3.x: fd21073: sched: Fix affinity logic
> Cc: <[email protected]> # 3.3.x
> Signed-off-by: Ingo Molnar <[email protected]>
>
> The tag sequence has the meaning of:
>
> git cherry-pick a1f84a3
> git cherry-pick 1b9508f
> git cherry-pick fd21073
> git cherry-pick <this commit>
> """
I know about these, and add them when I can. What I'm asking about is
if a fix and its prerequisites are sent as part of a larger series for
-next, then none of the prerequisites would be in Linus' tree, and I
can't use this format. What then? Mention the prerequisite patches'
subjects in the commit log?
We tend to bunch fixes into -next if they aren't critical (such as
a faulty clock that doesn't have any in tree users yet) or related
to the current -rc series.
Thanks
ChenYu
On Thu, Mar 22, 2018 at 12:19:18AM +0800, Chen-Yu Tsai wrote:
>On Thu, Mar 22, 2018 at 12:14 AM, Sasha Levin
><[email protected]> wrote:
>> On Tue, Mar 20, 2018 at 11:10:42AM +0800, Chen-Yu Tsai wrote:
>>>Hi,
>>>
>>>On Sun, Mar 4, 2018 at 6:28 AM, Sasha Levin
>>><[email protected]> wrote:
>>>> From: Chen-Yu Tsai <[email protected]>
>>>>
>>>> [ Upstream commit 68f37d862403e8f95337b2eca90af15d0b8cd5d7 ]
>>>>
>>>> The DDR1 PLL on the A33 is an oddball amongst the A33 CCU clocks.
>>>> It is a clock multiplier, with the effective multiplier in the
>>>> range of 12 ~ 255 and no offset between the multiplier value and
>>>> the value programmed into the register.
>>>>
>>>> Implement the zero offset and minimum value of 12 for this clock.
>>>>
>>>> Fixes: d05c748bd730 ("clk: sunxi-ng: Add A33 CCU support")
>>>> Signed-off-by: Chen-Yu Tsai <[email protected]>
>>>> Signed-off-by: Maxime Ripard <[email protected]>
>>>> Signed-off-by: Sasha Levin <[email protected]>
>>>> ---
>>>> drivers/clk/sunxi-ng/ccu-sun8i-a33.c | 18 +++++++++++-------
>>>> 1 file changed, 11 insertions(+), 7 deletions(-)
>>>>
>>>> diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-a33.c b/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
>>>> index e1dc4e5b34e1..bdbaf26f551f 100644
>>>> --- a/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
>>>> +++ b/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
>>>> @@ -159,13 +159,17 @@ static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_de_clk, "pll-de",
>>>> BIT(28), /* lock */
>>>> CLK_SET_RATE_UNGATE);
>>>>
>>>> -/* TODO: Fix N */
>>>> -static SUNXI_CCU_N_WITH_GATE_LOCK(pll_ddr1_clk, "pll-ddr1",
>>>> - "osc24M", 0x04c,
>>>> - 8, 6, /* N */
>>>> - BIT(31), /* gate */
>>>> - BIT(28), /* lock */
>>>> - CLK_SET_RATE_UNGATE);
>>>> +static struct ccu_mult pll_ddr1_clk = {
>>>> + .enable = BIT(31),
>>>> + .lock = BIT(28),
>>>
>>>As you undoubtedly noticed, this does not build. It needs commit
>>>cf719012b232 ("clk: sunxi-ng: mult: Support PLL lock detection")
>>>to be applied first. They were part of the same series.
>>
>> Thanks for the heads up!
>>
>>>Incidentally, how can we note these kinds of dependencies to make
>>>life easier for stable kernel maintainers?
>>
>> Yes! There are more details in Documentation/process/stable-kernel-rules.rst:
>>
>>
>> """
>> Additionally, some patches submitted via Option 1 may have additional patch
>> prerequisites which can be cherry-picked. This can be specified in the following
>> format in the sign-off area:
>>
>> Cc: <[email protected]> # 3.3.x: a1f84a3: sched: Check for idle
>> Cc: <[email protected]> # 3.3.x: 1b9508f: sched: Rate-limit newidle
>> Cc: <[email protected]> # 3.3.x: fd21073: sched: Fix affinity logic
>> Cc: <[email protected]> # 3.3.x
>> Signed-off-by: Ingo Molnar <[email protected]>
>>
>> The tag sequence has the meaning of:
>>
>> git cherry-pick a1f84a3
>> git cherry-pick 1b9508f
>> git cherry-pick fd21073
>> git cherry-pick <this commit>
>> """
>
>I know about these, and add them when I can. What I'm asking about is
>if a fix and its prerequisites are sent as part of a larger series for
>-next, then none of the prerequisites would be in Linus' tree, and I
>can't use this format. What then? Mention the prerequisite patches'
>subjects in the commit log?
>
>We tend to bunch fixes into -next if they aren't critical (such as
>a faulty clock that doesn't have any in tree users yet) or related
>to the current -rc series.
Just including the subjects would be fine too.
--
Thanks,
Sasha